Magellan eXplorist 200 User Manual

Magellan eXplorist 200

Reference

Manual

Topics:

•eXplorist 200 GPS Receiver

•Using the eXplorist 200

•Starting Up

•Navigation Screens

•Points of Interest

•Routes

•Track Logs

•Preferences

•Specifications

•Accessories

•Contacting Magellan Support

*** Warnings ***

IN THE INTEREST OF SAFETY, DO NOT USE THIS NAVIGATION DEVICE WHILE DRIVING

A VEHICLE.

Please do not try to change any settings on the Magellan® eXplorist™ while driving. Come to a complete stop or have a passenger make any changes. Taking your eyes off the road is dangerous and can result in an accident in which you or others could be injured.

USE GOOD JUDGMENT

This product is an excellent navigation aid, but it does not replace the need for careful orienteering and good judgment. Never rely solely on one device for navigating.

USE CARE

The Global Positioning System (GPS) is operated by the U.S. Government, which is solely responsible for the accuracy and maintenance of the GPS network. The accuracy of position fixes can be affected by the periodic adjustments to GPS satellites made by the U.S. government and is subject to change in accordance with the Department of Defense civil GPS user policy and the Federal Radionavigation Plan. Accuracy can also be affected by poor satellite geometry and obstructions, such as buildings and large trees.

USE PROPER ACCESSORIES

Use only Magellan cables and antennas; the use of non-Magellan cables and antennas may severely degrade performance or damage the receiver, and will void the warranty.

LICENSE AGREEMENT

Thales Navigation grants you, the purchaser, the right to use the software supplied in and with Thales Navigation GPS products (the “SOFTWARE”) in the normal operation of the equipment in accordance with the terms of the End User License Agreement that is included with the product.

The SOFTWARE is the property of Thales Navigation and/or its suppliers and is protected by United States copyright laws and international treaty provisions; therefore, you must treat the SOFTWARE like any other copyright material.

You may not use, copy, modify, reverse engineer or transfer this SOFTWARE except as expressly provided in the license. All rights not expressly granted are reserved by Thales Navigation and/or its suppliers.

* * *

No part of this guide may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose other than the purchaser’s personal use without the prior written permission of Thales Navigation.

* * *

Operation is subject to the following two conditions: (1) this device may not cause interference, and

(2) this device must accept any interference, including interference that may cause undesired operation of the device.

© 2004 Thales Navigation, Inc. All rights reserved.

The Magellan Logo, Magellan, eXplorist and TrueFix are trademarks of Thales Navigation.

631182-01 C

Table of Contents
		i

eXplorist 200 GPS Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

Features of the Magellan eXplorist GPS Receiver. . . . . . . . . . . . . . . . . . 1

Button Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Installing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

Using the eXplorist 200 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Going to a Destination . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Saving Your Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Tracing Your Steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Additional Features. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Starting Up. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Turning the eXplorist On . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Turning the eXplorist Off . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Turning the Display Backlight On/Off . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Using the eXplorist for the First Time . . . . . . . . . . . . . . . . . . . . . . . . . 10

Conclusion. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

Navigation Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Accessing the Navigation Screens . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Map Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Map Screen Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Changing Map Scale . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Map Screen Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

Showing or Hiding Map Information . . . . . . . . . . . . . . . . . . . . . . . 16

Customizing the Map Information . . . . . . . . . . . . . . . . . . . . . . . . . 17

Changing the Map Orientation . . . . . . . . . . . . . . . . . . . . . . . . . . . 18

Changing the Primary Usage. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

Compass Screen. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Compass Screen Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20

Customizing the Information Fields . . . . . . . . . . . . . . . . . . . . . . . . 21

Position Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Position Screen Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22

Resetting the Trip Odometer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Satellite Status Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24

Table of Contents
		ii

Points of Interest . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Marking Your Position . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Quick-Marking Your Position. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25

Marking Your Position (Personalized). . . . . . . . . . . . . . . . . . . . . . . 26

Making POIs for Locations Other Than Your Present Position . . . . . . . . 27

Marking a Position by Entering Coordinates . . . . . . . . . . . . . . . . . . 27

Marking a Position using the Map Cursor. . . . . . . . . . . . . . . . . . . . 28

Marking a Position from a Map Object. . . . . . . . . . . . . . . . . . . . . . 28

The POI Database. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29

Searching for a User-Entered POI . . . . . . . . . . . . . . . . . . . . . . . . . 29

Searching for a Preloaded POI using Nearest . . . . . . . . . . . . . . . . . 30

Searching for a Preloaded POI using Alphabetical . . . . . . . . . . . . . 31

Editing a User-Created POI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

Deleting a User-Created POI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

Viewing a User-Created POI on the Map Screen . . . . . . . . . . . . . . . . . 34

Copying a Preloaded POI. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

Viewing a Preloaded POI on the Map Screen. . . . . . . . . . . . . . . . . . . . 36

Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

GOTO Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37

Creating a GOTO Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

Creating a GOTO Route from the Map Cursor . . . . . . . . . . . . . . . . . 39

Creating a GOTO Route to a Map Object . . . . . . . . . . . . . . . . . . . . 40

Multi-Leg Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41

Creating a Multi-leg Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

Activating/Deactivating a Route. . . . . . . . . . . . . . . . . . . . . . . . . . . 43

Changing the Destination Leg of an Active Route . . . . . . . . . . . . . . 44

Editing a Saved Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45

Reversing a Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

Deleting a Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

Copying a Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Viewing a Route on the Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

Table of Contents
		iii

Track Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Track Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50

Stopping and Resuming Active Track Logging . . . . . . . . . . . . . . . . 51

Starting a New Active Track Log . . . . . . . . . . . . . . . . . . . . . . . . . . 52

Saving an Active Track Log. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53

Creating a BackTrack Route . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

Clearing the Active Track . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Converting the Track Log to a Route . . . . . . . . . . . . . . . . . . . . . . . 56

Viewing the Track Log on the Map. . . . . . . . . . . . . . . . . . . . . . . . . 57

Working with Saved Track Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Following Saved Track Logs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Reversing a Saved Track Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58

Deleting a Saved Track Log . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59

Preferences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 60

Restarting the GPS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 61

Setting the Map Units. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

Selecting Navigational Units of Measure . . . . . . . . . . . . . . . . . . . . 63

Selecting the North Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . 64

Selecting the Coordinate System. . . . . . . . . . . . . . . . . . . . . . . . . . 65

Selecting the Map Datum. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

Using the Power Management Tool. . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Setting the Power-Off Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67

Setting the Light Timer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

Personalizing the eXplorist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

Selecting Languages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Clearing Memory . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Clearing All Track Logs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Clearing All User-Entered POIs and Routes . . . . . . . . . . . . . . . . . . 72

Clearing All Routes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72

Clearing All Track Logs, User-Entered POIs, and Routes . . . . . . . . . 72

Reseting the eXplorist to Factory Defaults . . . . . . . . . . . . . . . . . . . 73

Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Contacting Magellan Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

eXplorist 200 GPS Receiver		1

Features of the Magellan eXplorist GPS receiver:

•	Built-in background map	•	TrueFix™ GPS technology
• Preloaded points of interest		• 3 meter accuracy (WAAS/EGNOS)
•	Rugged design, rubber-protected	•	Multiple track logs
•	8 MB of background map	• Stores up to 500 points of interest
• Superior tracking with 14 parallel channels			and 20 routes

• 14 hour+ battery life on 2 AA batteries	• Pocket-sized and waterproof to IPX-7

Antenna

On/Off Button

Display Backlight

Button

ENTER

Arrow Joystick

ZOOM OUT

ZOOM IN

MENU

NAV

GOTO

MARK

ESCAPE

eXplorist 200 GPS Receiver (front)

eXplorist 200 GPS Receiver
		2

Button Descriptions:

On/Off

Backlight

ENTER

ESCAPE

ZOOM IN

ZOOM OUT

MENU

NAV

MARK

GOTO

Arrow joystick

Turns the eXplorist on or off.

Turns the display backlight on. Sequences from off to low to high intensity.

Used to access highlighted menu items or accept highlighted buttons.

Cancels data inputs.

Closes the accessed function and goes back to the last viewed screen.

Steps backward through the navigation screens.

Used on the Map screen to zoom in on the map displayed. The map display can be zoomed in to 100 ft. (35.0 m).

Also used to quickly step through the list of POIs when doing an alphabetical search.

Used on the Map screen to zoom out on the map displayed. The map display can be zoomed out to 1700 mi (2700 km).

Also used to quickly step through the list of POIs when doing an alphabetical search.

Brings up a menu with available options. Options can be selected by using the arrow joystick to highlight the option and pressing ENTER to access it.

Steps through the navigation screens. (Map screen > Compass screen > Position screen > Satellite Status screen)

Used to save your present position as a point of interest. Points of interest that you save are stored in the My Points of Interest portion of the database.

Creates a one-leg route from your present position to a destination selected from the Points of Interest database or by using the cursor on the background map.

Pans the cursor on the Map screen.

Moves the highlight bar to select menu options and data-entry fields.

eXplorist 200 GPS Receiver
		3

Wrist Lanyard

Strap Mounting

Hole

	Battery Door
	Fastener
	(Unscrew to
	open battery
	door to install
Battery Door	batteries.)

eXplorist 200 GPS Receiver (back)

eXplorist 200 GPS Receiver
		4

Installing the Batteries

The eXplorist 200 uses two AA batteries that are installed as shown in the accompanying diagram. Be sure to observe the proper polarity when installing the batteries.

Under normal operating conditions you can expect to get more than 14 hours of battery life when using fresh batteries.

Tips on conserving battery life:

•Turn the eXplorist off when not in use. Whether you are moving or standing still, the eXplorist is constantly calculating position fixes and using power at the same rate. If you are going to be at the same position for any length of time, turn the eXplorist off.

•Use the Power Timer to automatically turn the eXplorist off. The Power Timer option allows you to set a time that the eXplorist will automatically turn off when none of the buttons have been pressed and you are not moving for a selected time. You can select from 5, 10, 30 or 60 minutes.

•Use the display backlight sparingly. The most severe drain on the batteries is the use of the display backlight. You will notice a drastic drop in battery life with the backlight display on continuously. You should use the Light Timer to set a time interval that the display backlight will automatically turn off when none of the buttons have been pressed.

Setting the Power Timer

From any Nav screen press MENU. Highlight Preferences and press ENTER. Highlight Pwr Management and press ENTER twice. Use the arrow joystick to select 5 Minutes, 10 Minutes, 30 Minutes, 60 Minutes or Off. Press ENTER. Press NAV to return to the last viewed navigation screen.

Setting the Light Timer

From any Nav screen press MENU. Highlight Preferences and press ENTER. Highlight Pwr Management and press ENTER. Use the down arrow to highlight the Light Timer field. Press ENTER. Use the arrow joystick to select 30 Seconds, 1 Minute, 2 Minutes, 4 Minutes, 10 Minutes or Timer Off. Press ENTER. Press NAV to return to the last viewed navigation screen.

Using the eXplorist 200		5

The eXplorist 200 uses information from the GPS satellites orbiting the earth to provide you with detailed information about your exact location. This is the foundation that your eXplorist will use to provide you with the necessary information to arrive at your destination.

Going to a Destination

The most common use of your eXplorist will be to provide you with the navigation tools you’ll need to arrive at your chosen destination. The simplest route, and the one used most, is a GOTO route. This is a route that is computed as a straight line from where you are to where you want to go.

Step One: Compute Your Position

The basic operation of your eXplorist is to use the GPS satellites to compute your present position. This is done internally in the software of your eXplorist. The only thing that you need to do is to give your eXplorist a clear view of the sky so that it can receive the signals from the satellites.

Do:

•Point the antenna up toward the sky.

•Maintain a clear view of the sky.

Don’t:

•Cover the antenna with your hand or other objects.

•Point the antenna down.

•Stand under trees or other heavy foliage.

•Stand where the satellite signals are being blocked by large obstructions (such as buildings, in a narrow canyon, etc.)

If you find that the eXplorist is not computing a position, just move to a place that has a better view of the sky.

Anytime that you want to view the status of the satellites and their signal strength, switch to the Satellite Status screen. Here, you will graphically see the satellites and their relative signal strength. You need at least three satellites with good signal strength (indicated by black bars) to compute your position. A computed position with only three satellites is termed a 2D position fix. When you are getting a 2D position fix, your elevation is not being computed. To add elevation to your position fix, you need at least four satellites with good signal strength. Positions that use four or more satellites are called 3D position fixes.

3D Position Fix

Tracking 7....

Using the eXplorist 200
		6

Step Two: Where Do You Want To Go?

Now that the eXplorist knows where you are, you need to tell it where you want to go. There are many different ways you can do this, but the simplest and most commonly used is a “GOTO” route. This is a one-leg route with a beginning (where you are now) and a destination (where you want to go). The destination is selected by using the Points of Interest database. This database has two main options: positions you have saved (My Points of Interest) or points of interest that have been preloaded into your eXplorist (Background Map).

Creating a GOTO route is as simple as pressing the GOTO button and selecting the destination from the points of interest database.

Step Three: Calculating Movement

As you move, your eXplorist is constantly calculating new positions, comparing the new position to the previous position and calculating such things as heading and speed. This is all done in the eXplorist’s software communicating with the satellites and is instantaneously shown on your display.

Step Four: Providing Directions

Your eXplorist constantly computes a direct line from your present position to your destination. From there, it will provide you instructions to guide you along that straight path. Unless you are on a large body of water, it will be unlikely that you will be able to follow these instructions exactly. To compensate for that, your eXplorist automatically updates the route, providing you with up-to-date information about getting to your destination.

GOTO routes are the simplest and most commonly used feature of your eXplorist 200. With just the GOTO button the eXplorist will provide you with the tools needed to get to any point of interest stored in your database.

Saving Your Position

Another commonly used feature of the eXplorist is saving your position to the points of interest database. This feature is accessed by pressing the MARK button. When saving your position, you can also add attributes such as the icon or a name for the point of interest. This will help you to find this spot in the future when accessing it from the points of interest database.

Suppose that you have set up camp for the night. Tomorrow, you plan on doing some nature exploring and you want to be able to come back to the campsite when you are done. Press the MARK button and set the name of the point of interest to “Camp”.

After your hiking is done, simply use the GOTO button and select “Camp” from the list of My Points of Interest. It’s that simple to find your way back.

While out fishing on the lake, you come across the perfect spot for catching your limit. Next year, you want to be able to come back to this same spot. Turn on your eXplorist; and after it has computed your position, press the MARK button to save it. This time you can enter the name “Catfish1” and save your point of interest. Next year, you can be back at the same hot spot with just a press of the GOTO button.

Using the eXplorist 200
		7

A simpler example, and one you can do at just about any time, is finding your car in that ocean of other cars in the shopping mall parking lot. Just park your car, step outside and let your eXplorist compute your position. (Make sure that you have a clear view of the sky.) Using the MARK button, save this position with the name “Car”. When you are done shopping, just go outside the mall and create a GOTO with the destination “Car”. No matter where you parked, your eXplorist will guide you back, simply and easily.

Tracing Your Steps

Hikers, mountain bikers and outdoor enthusiasts often need the option of leaving a trail of breadcrumbs that they can follow back to where they started. The eXplorist has a feature called BackTrack that enables you to do just that.

It was mentioned earlier that your eXplorist is constantly computing your present position and that you can save your position by using the MARK button. Now, imagine that your eXplorist automatically saved your computed positions as you moved along the trail. Pretty soon there would be a set of saved positions, like breadcrumbs, that represents the trail you have taken. This is exactly what the eXplorist does. It saves the computed positions as hidden points of interest and strings them together to represent your travels. This is called your Track, and the hidden points of interest are your Track Log.

Your eXplorist enables you to use this Track, reverse it and navigate you along the same path that you followed to get you back to your destination.

You might drive to the ranger station and follow the trail that leads you to the waterfalls you have been wanting to see. With your eXplorist turned on and able to compute position fixes, you continue along the trail. The trail winds along and has many smaller trails attached to it. As the day progresses you arrive at the falls. When it’s time to head back to your car, you access your Track Logs list and select the Active Track log. Now, press MENU, highlight BackTrack and press ENTER. Your eXplorist will now seamlessly guide you along the path, tracing your footsteps, back to where you started.

Another nice feature of Track Logs, which you may find useful, is that you are able to save the Track Logs and recall them at any time. In the above example, at the waterfall, you could save that track and use it anytime you wanted to go back.

Using the eXplorist 200
		8

Additional Features

Your Magellan eXplorist contains all of the features that you would expect from a high-quality Magellan-brand handheld navigation device, as well as many more to make your outdoor experience more enjoyable. You have the ability to customize the navigation screens, enabling you to view the information that is important to you. The eXplorist makes full use of the Map screens, enabling you to graphically see your position, the route you are navigating, the path you have trekked (Track), and points of interest icons. There is a builtin odometer so that you can log the length of your journey. User preferences enable you to set up and maintain your eXplorist so that it fits your needs and requirements. The eXplorist gives you all of this and more in an easy-to-use, portable navigation tool that includes built-in help files that you can access in the great outdoors.

Magellan eXplorist 200 with optional

swivel mounting bracket

Summary

Go from this...

to this...

with this.

Starting Up		9

Turning the eXplorist On

To turn the eXplorist on, press the POWER button on the top right side. To prevent the eXplorist from being turned on accidentally, draining the batteries, you need to press ENTER when the Startup screen is displayed. You have approximately 30 seconds between pressing the POWER button and pressing the ENTER button, otherwise the eXplorist will automatically turn itself off.

Turning the eXplorist Off

To turn the eXplorist off, press the POWER button on the top right side.

There is a 5-second countdown after you press the POWER button. If you change your mind and decide to leave the eXplorist on, just press the ESC button. If you press the POWER button during this countdown period, the eXplorist will immediately turn off.

Turning the Display Backlight On/Off

The display backlight has three levels of intensity: off, low and high. When the eXplorist is first turned on, the display backlight is off. Press the LIGHT button on the top left side of the eXplorist to turn the backlight on low. Pressing the LIGHT button a second time sets the backlight to high. To turn off the backlight, press the LIGHT button again.

Backlight intensity changes each time you press the LIGHT button.

REMEMBER: Using the display backlight causes severe drain on the batteries.

Finding Satellites

Tracking 0...

Starting Up
		10

Using the eXplorist for the First Time

Turn the eXplorist on. Press the Power button. When the Startup screen is displayed, press

ENTER.

Select Language. When you turn on the eXplorist for the first time, you are given the option of selecting one of the ten languages that can be used.

You can change the language selection at any time by accessing Menu > Preferences > Languages.

Tip: If you accidentally change the language but you can’t read the text and need to change it back, press the NAV button until the Satellite Status screen is displayed. Press MENU. Use the Arrow joystick to highlight the fourth line and press ENTER. Use the Arrow joystick to highlight the fifth line and press ENTER. The Language Select screen will be displayed.

Read Warning. When you agree to the warning statement, press ENTER to continue.

Language

English

Français

Deutsch

Nederlands

Suomi

Español

Italiano

Português

Svenska

Norsk

PRESS

Use arrow joystick to move the highlight up and down.

Press ENTER to accept

WARNING!

All data is provided for reference only.

You assume full responsibility and risk when using this device.

PRESS

TO AGREE

Press ENTER to continue

Compute Initial Position. For this operation, it is best if you are outside and have a clear, unobstructed view of the sky. Without a clear view, this will take much longer and could result in the eXplorist being unable to compute the initial position

automatically.

The eXplorist begins to compute your initial position. This may take a few minutes while it is doing a cold start.

Normally, when you first turn the eXplorist on it will compute your position in a matter of seconds when able to do a warm start. (An explanation of cold start vs. warm start is provided following this section.)

The Satellite Status screen is displayed, showing you the progress of the collection of satellite data.

Satellite Status screen shows how many satellites are being tracked, as well as the relative strength of the signal.

Starting Up
		11

The Satellite Status screen will continuously update, and you will be able to graphically see how well your eXplorist is performing.

3D Position Fix

Tracking 7....

When the eXplorist has enough information to compute a position fix, the Satellite Status screen is replaced with the Map screen. The arrow cursor in the center of the Map screen represents your position. As you move, the arrow will point in the direction you are traveling.

Tip: Use the ZOOM IN and ZOOM OUT buttons to change the map scale so that you can see your present position better.

Cumberland River
		62
River	62
641
Heading		Speed
060 M		48.0	M
			H

If the eXplorist is unable to compute your initial fix in a few minutes: If the eXplorist determines that it is unable to track the satellites within a few minutes, it will present you with the following screens in an effort to better determine its

approximate location.	Region
Select Region. Use the arrow joystick to highlight the region that
you are located in. With the region highlighted, press the ENTER
button.	Enter Coord
	USA
	Americas
	Europe
	Asia East
	Asia West

Select Area. This displays a list of areas for the region you selected. Use the Arrow joystick to highlight the area that applies to you, and press the ENTER button.

Area

Alabama

Alaska

Arizona

Arkansas

California

Colorado

Starting Up
		12

Enter Current Time. Use the arrow joystick to enter the current time.

Arrow Joystick Up: Increases the highlighted number Arrow Joystick Down: Decreases the highlighted number

Arrow Joystick Right: Moves the highlight one character to the right Arrow Joystick Left: Moves the highlight one character to the left

Time

37° 00.000N 119° 00.000W

0FT

09:06AM

16 JAN 04

Toggle between AM and PM by moving the arrow joystick up or down when

Done

AM or PM is highlighted.

When you have entered the correct time, press ENTER.	The latitude and longitude
	that represents the center
	of the region and area you
	selected is displayed.

Enter the Date. Use the Arrow joystick to set the date displayed to the current date.

Arrow Joystick Up: Increases the highlighted number Arrow Joystick Down: Decreases the highlighted number

Arrow Joystick Right: Moves the highlight one character to the right Arrow Joystick Left: Moves the highlight one character to the left

When the month is highlighted, use the arrow joystick up or down to scroll through the list of months.

Date

37°00.000N

119°00.000W

0FT

10:16AM

16 JAN 04

Done

When you have entered the correct date, press ENTER.

Accept Information. The Done button is highlighted at the bottom of the display. Review the information you entered; if correct, press ENTER.

Tip: If the time or the date is incorrect, you can fix it now. Use the Arrow joystick to highlight the time or the date field that you want to change. With the field highlighted, press ENTER. You can now change the information using the same technique used before.

The Satellite Status screen is displayed again and the eXplorist will try to compute your position using the information you just provided.

Tip: If you notice that the satellite signal-strength bars are still not changing, try moving to a new location where you have a clearer view of the sky.

As before, when the eXplorist computes the initial position, the Map screen will be displayed, with your computed position indicated by the arrow cursor in the middle of the display.

Date

37° 00.000N

119° 00.000W

0FT

10:16AM

21 MAY 04

Done

Finding Satellites

Tracking 0...

Starting Up
		13

Cold vs. Warm Start. When the eXplorist is turned on, one of the first things it does is to find out which satellites are overhead, along with their relative position. It does this by using a built-in satellite almanac. This almanac, when given the current date, time and approximate position, can provide the eXplorist with information on which satellites are overhead and their approximate relationship to the eXplorist. Now with information on satellite availability, the eXplorist can begin setting its internal satellite channels to receive satellite transmissions.

Cold Start. Cold start is defined as when the eXplorist does not have an approximate position to use when referring to its almanac. This can occur when:

•The eXplorist is turned on for the first time after purchase. The memory is cleared prior to shipping so that any position that may have been in the eXplorist is set to a null value.

•If you have cleared the eXplorist's memory, (found in Preferences) all of the memory will be cleared and the last computed position will be set to a null value.

•If you have traveled with your eXplorist with it turned off, the last position saved may be so far away that when the eXplorist begins looking for satellites, the ones it is expecting to find are not there. (As a rule of thumb, any time you move for more than 500 mi [804.7 km] with the eXplorist turned off, there is a good chance that it will start up using a cold start.

A cold start should take no more than 2-3 minutes to compute the initial position fix.

Warm Start. Warm starts are when the last position calculated before the eXplorist was turned off is still in memory and you are in the same approximate position. Most of the time that the eXplorist is turned on, it will be in its warmstart mode. With a clear view of the sky, the eXplorist should compute its position in a matter of seconds.

Conclusion

This concludes the initial startup procedure for the Magellan eXplorist 200. Once the Map screen is displayed, you have successfully initialized the eXplorist and are ready to go.

Now would be a good time to familiarize yourself with the different navigation screens (using the NAV button) and to set any preferences that may be different from the factory defaults.

Navigation Screens		14

Accessing the Navigation Screens

The eXplorist has three navigation screens, as well as a Satellite Status screen that can be accessed by pressing the NAV button. Each screen provides the same information in a different format, giving you the choice of choosing the screen that best suits your needs.

	To: Canyon			Location
Glendora	Speed	Distance		34°06.556N
	4.3 MH	5.84MI		117°49.563W
210	NAV		NAV
	San Dimas
				Elevation	Accuracy
ent				1292 FT	25FT
				Date/Time
10	10		ESC	01 FEB 04
	ESC
vina
1.60mi				03:30:36 PM
Heading	Speed			Trip Odometer	Battery

o	4.3	M	M
352 M		H	0000.0 I

			3D Position Fix
			Tracking 7....
ESC							ESC
NAV						NAV

Tip: The ESC button will also set through the navigation screens, just like the NAV button but in the reverse order.

Map Screen

The first, and most commonly used, screen is the Map screen. The Map screen displays your position, as well as POIs and any background map data for the area displayed.

Highlights of the Map screen:

•Use the zoom in/out buttons to change the scale.

•The arrow cursor in the middle of the display indicates your position and, if moving, points in the direction you are heading.

•Press MARK to save your position.

•Use the Arrow joystick to move the cursor. The arrow cursor changes to a crosshair cursor, with any available information about the position of the cursor at the bottom of the display. You can also save the position of the crosshair cursor as a POI by pressing the MARK button.

•Press ESC when you are done panning with the crosshair cursor to display your present position with the arrow cursor.

•Press MENU and select Hide Map Info or Show Map Info to turn the information boxes at the bottom of the screen on or off.

•Press MENU and select Customize page to change the information displayed at the bottom of the screen.

•Press MENU and select Map Setup to change the orientation of the screen and the primary usage (land or marine).

	Navigation Screens
				15
	Map Screen Overview

Route

Marker

Track Indicator

Map Scale

Data Field 1

Glendora

210 San Dimas

ent
vina		10
	10
1.60mi
Heading	Speed
o	4.3	M
352 M		H

Position Cursor

Pan Cursor (used when in Cursor Mode)

Hourglass (used when position is unknown and eXplorist is trying to compute the position)

Data Field 2

Changing Map Scale

Press the Zoom In or the Zoom Out buttons to change how much of the map is displayed on the screen. The map scale indicator in the bottom left corner of the map indicates the relative distance between the two end-points of the scale. The scale can be changed from 1700 mi (2700 km) to 100 ft (35.0 m).

Tip: Press and hold the Zoom In or the Zoom Out buttons to rapidly step through the map scales.

Map Screen Modes

The Map screen has two modes that it can be in: position or cursor. In the Position mode the Map screen displays your position, indicated by the arrow icon in the center of the map. The arrow not only displays your position but also,

when moving, will point in the direction you are heading.

The Position mode is the default mode for the Map screen.	Glendora
Whenever you enter the Map screen it will be in the Position	210	San Dimas
mode.	ent

vina		10
	10
1.60mi
Heading	Speed
o	4.3	M
352 M		H

The Map screen in the Position Mode

Navigation Screens
		16

In the Cursor mode, you have a cursor icon displayed that you can use to pan around the map. The information displayed at the bottom of the screen provides you with the heading and distance of the cursor from your present position. In the Cursor mode you can:

•scroll around the map, checking available information for areas on the map not displayed around your present position

•create a POI for the position indicated by the cursor

•create a GOTO route to the position indicated by the cursor location

•get detailed information about POIs or map objects found at the cursor location

30

San Dimas

10

10

Pomona

57

60

1.60mi 60

Cursor
o	M
114 M	7.31I

The Map screen in the Cursor Mode

These options will be explained in the section of this manual on creating POIs and GOTO routes.

To enter the Cursor mode, use the Arrow joystick to move the cursor. As soon as the joystick is moved, a crosshair cursor is displayed and the bottom of the screen changes to provide information about the cursor position.

To exit the cursor mode, press the ESC button. When pressed, the Map screen is returned to the Position mode, with your present position displayed in the center of the screen.

Showing or Hiding Map Information

The information at the bottom of the Map screen provides you with information that can be used to assist you in navigating to your destination. However, you may want to display more of the map and may not need this information. The eXplorist gives you the capability to turn this information on or off.

1.While viewing the Map screen, press MENU.

2.With Hide Map Info or Show Map Info highlighted, press ENTER.

Glendora

210 San Dimas

ent

10

vina

10

1.60mi

Heading Speed

o	4.3	M
352 M		H

Glendora
210	San Dimas
ent
vina	10
	10
alley
	57
1.60mi	I-210

The Map screen with map information shown

The Map screen with map information hidden

Navigation Screens
		17

Customizing the Map Information

The information displayed at the bottom of the screen can be customized to change what is shown in the two map information fields. You can select from:

•Bearing

•Distance

•Speed [default]

•Heading [default]

•ETA (Estimated Time of Arrival)

•ETE (Estimated Time Enroute)

•Elevation

•Time

•Date

To customize the map information:

1.While viewing the Map screen, press MENU.

2.Use the Arrow joystick to highlight Customize page.

3.Press ENTER.

4.The title bar for one of the fields is highlighted. Use the Arrow joystick to highlight the title bar for the field you want to customize.

5.Press ENTER.

6.Highlight the information you want displayed from the list.

7.Press ENTER.

8.The highlight will automatically jump to the other field. Go back to step 5 to change the information displayed for this field.

9.When the information to be displayed is chosen, press ESC to exit the customize function.

Customize page

Glendora
Bearing
Distance	San Dimas
210

Speed

Heading

ent ETA

ETE

vina Elevation

10

10

Time

1.60mi

Date

Heading Speed

o	4.3	M
352 M		H

Navigation Screens
		18

Changing the Map Orientation

The default orientation for the Map screen is North Up. This means that the top of the display represents true north. This orientation can be changed so that the top of the display is more useful to you. You can choose from:

•North Up [default]. This orientates the top of the map display to represent true north.

•Course Up. In course up, the top of the map displays the direction to your destination. (When there is not an active route, the top of the display indicates true north.)

•Track Up. In track up, the top of the map display changes to reflect your heading. (If you are not moving, the top of the display indicates true north.)

Note: In Course Up and Track Up, a north indicator is displayed in the upper right corner of the display. This arrow points in the direction of true north.

To change the map orientation:

1.While viewing the Map screen, press MENU.

2.Use the Arrow joystick to highlight Map Setup.

3.Press ENTER.

4.Use the Arrow joystick to highlight the Orientation field.

5.Press ENTER.

	6.	Use the Arrow joystick to highlight North Up,		Orientation
		Course Up or Track Up.
				North Up
	7.	Press ENTER.		Course Up
				Track Up

8.Press MAP to return to the Map screen.

Navigation Screens
		19

Changing the Primary Usage

The Map screen can be changed to be primarily used on land (default) or marine.

When in land usage, land areas are displayed as white areas on the display and water is displayed as dark gray.

The opposite is true when the map is set for marine usage. (Water is white and land areas are displayed as dark gray.)

This is provided as an option to provide you with the ability to view the text and map details more easily, depending on where you are navigating.

To change the primary usage:

1.While viewing the Map screen, press MENU.

2.Use the Arrow joystick to highlight Map Setup.

3.Press ENTER.

4.Use the Arrow joystick to highlight the Primary Usage field.

5.Press ENTER.

6.Use the Arrow joystick to highlight Marine or Land.

7.Press ENTER.

8.Press NAV to return to the Map screen.

South Lake Tahoe

Rocky Slo

50

88

50

89

88

3.50mi

Heading Speed

030°M 48.0M

H

The Map screen with the primary usage in Land

South Lake Tahoe
50	Rocky Slo
	88
50
89
	88
3.50mi
Heading	Speed
030°M	M
	48.0H

The Map screen with the primary usage in Marine

Navigation Screens
		20

Compass Screen

The Compass screen provides an easy-to-use graphical compass that should be familiar to most GPS users.

Highlights of the Compass screen:

•With an active route, the top of the Compass screen displays the name of the destination.

•Press MENU and select Customize page to change the information displayed at the top of the screen.

•When there is no active route, the graphical compass performs like a standard compass, indicating to your heading as referenced to true north. (Note: You must be moving at least 0.5 mph for the compass to display heading information.)

•With an active route, the compass graphically displays an icon representing your destination. The compass arrow points in the direction you are heading when you are moving.

Compass Screen Overview

Destination	To: VIEW
	Speed		Distance
	2.8	M	0.84	M
Data Field 1		H		I	Data Field 2
Destination Icon			N
	W		E
Moon Locator			S
Icon					Sun Locator Icon

The top of the screen (the header bar) displays the name of the destination if you have an active route. Without an active route, the destination name is blank.

Also, two navigation information fields (customizable) are displayed.

When there is no active route, the graphical compass indicates the direction you are travelling. (When you are not moving, the compass points to the last computed heading.) When there is an active route, an icon representing the destination is displayed outside the compass diameter, with the compass arrow pointing in the direction you are heading. When the compass arrow points directly to the destination icon, you are going in the direction of your destination.