26LT670H
32LT670H
37LT670H
42LT670H
Lodging Guest Interactive Pro:Centric™ TVs
Commercial Mode Setup Guide
Note: Selected features shown in this guide may not be available on all models.
EXPERIENCED INSTALLER
Automated Installation Routine Wizard pages 11 – 13
Custom Master TV Setup pages 14 – 17
Cloning Information pages 28 – 36
FTG Mode of Operation pages 37 – 48
|
|
© Copyright 2012 LG Electronics U.S.A., Inc. |
P/N: 206-4213 (Rev A) |
|
|
For Customer Support/Service, please call:
1-888-865-3026
The latest product information and documentation is available online at: www.LGsolutions.com/products
MODEL and SERIAL NUMBER
The model and serial numbers of this TV are located on the back of the cabinet. For future reference, LG suggests that you record those numbers here:
Model No._________________ Serial No._______________
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USERSERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
POWER CORD POLARIZATION:
This product is equipped with a 3-wire grounding-type alternating current power plug. This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the 3-wire grounding-type plug.
NOTE TO CABLE/TV INSTALLER:
This reminder is provided to call the cable TV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.
REGULATORY INFORMATION:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
Do not attempt to modify this product in any way without written authorization from LG Electronics U.S.A., Inc. Unauthorized modification could void the user’s authority to operate this product.
COMPLIANCE:
The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632, USA • Phone: 1-201-816-2000
Marketed and Distributed in the United States by LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632
2 |
© Copyright 2012 LG Electronics U.S.A., Inc. |
206-4213 |
IMPORTANT SAFETY INSTRUCTIONS
1.Read these instructions.
2.Keep these instructions.
3.Heed all warnings.
4.Follow all instructions.
5.Do not use this apparatus near water.
6.Clean only with dry cloth.
7.Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.
8.Do not install near any heat sources, such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10.Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point where it exits from the apparatus.
11.Only use attachments/accessories specified by the manufacturer.
12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer or sold with the apparatus. When a cart is used, use caution when moving the cart/ apparatus combination in order to avoid injury from tip-over.
PORTABLE CART WARNING
13.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
14.Never touch this apparatus or antenna during a thunder or lighting storm.
15.When mounting a TV on the wall, make sure not to install the TV by the hanging power and signal cables on the back of the TV.
16.Do not allow an impact shock or any objects to fall into the product, and do not drop objects onto the screen.
17.Power Cord
Caution: It is recommended that appliances be placed upon a dedicated circuit; that is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page in the Owner’s Manual to be certain.
Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as twisting, kinking, or pinching or being closed in a door or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
Do not use a damaged or loose power cord. Be sure to grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the TV.
18.Overloading
Do not connect too many appliances to the same AC power outlet as this could result in fire or electric shock. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in fire or electric shock.
19.Outdoor Use/Wet Location
Warning: To reduce the risk of fire or electrical shock, do not expose this product to rain,
moisture or other liquids.
Do not touch the TV with wet hands. Do not install this product near flammable objects such as gasoline or candles or expose the TV to direct air conditioning.
Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc., on or over the apparatus (e.g., on shelves above the unit).
20.Grounding
Ensure that you connect the earth ground wire to prevent possible electric shock (i.e., a TV with a three-prong grounded AC plug must be connected to a three-prong grounded AC outlet). If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightning rods, or gas pipes.
21.Disconnect Device
The mains plug is the disconnecting device. The plug must remain readily operable.
As long as this unit is connected to the AC wall outlet, it is not disconnected from the AC power source even if you turn off this unit by SWITCH.
(Continued on next page)
206-4213 |
3 |
IMPORTANT SAFETY INSTRUCTIONS
(Continued from previous page)
22.Outdoor Antenna Grounding
If an outside antenna or cable system is connected to the product, follow the precautions below.
An outdoor antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits or where it can come into contact with such power lines or circuits as death or serious injury can occur.
Be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges.
Article 810 of the National Electrical Code (NEC) in the U.S.A. provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna-discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
Antenna Grounding According to NEC, ANSI/NFPA 70
Ground Clamp |
Antenna Lead in Wire |
|
|
|
Antenna Discharge Unit |
|
(NEC Section 810-20) |
|
Grounding Conductor |
Electric Service |
(NEC Section 810-21) |
|
|
Equipment |
Ground Clamps |
|
|
|
Power Service Grounding |
|
Electrode System (NEC |
|
Art 250, Part H) |
23.Cleaning
When cleaning, unplug the power cord and wipe gently with a soft cloth to prevent scratching. Do not spray water or other liquids directly on the TV as electric shock may occur. Do not clean with chemicals such as alcohol, thinners or benzene.
24.Transporting Product
Make sure the TV is turned Off and unplugged and that all cables have been removed. It may take two or more people to carry larger TVs. Do not press against or put stress on the front panel of the TV during transport.
25.Ventilation
Install the TV where there is proper ventilation. Do not install in a confined space such as a bookcase. Do not cover the TV with cloth or other materials (e.g., plastic) while it is plugged in. Do not install in excessively dusty places.
26.Do not touch the ventilation openings, as they may become hot while the TV is operating.
27.If you smell smoke or other odors coming from the TV or hear strange sounds, unplug the power cord, and contact an authorized service center.
28.Do not press against the front panel of the TV with your hand or a sharp object (e.g., a nail, pencil, or pen) or make a scratch on it.
29.Keep the product away from direct sunlight.
30.Dot Defect
The LCD panel is a high technology product with resolution of two million to six million pixels. In a very few cases, you could see fine dots on the screen while you are viewing the TV. Those dots are deactivated pixels and do not affect the performance and reliability of the TV.
31.Generated Sound
“Cracking”: A cracking noise that occurs while the TV is On or when it is turned Off is generated by plastic thermal contraction due to temperature and humidity. This noise is
common for products where thermal deformation is required.
Electrical circuit humming/panel buzzing: A low level noise is generated from a high-speed switching circuit, which supplies a large amount of current to operate a product. It varies depending on the product. This generated sound does not affect the performance and reliability of the product.
32.For LCD TV
If the TV feels cold to the touch, there may be a small “flicker” when it is turned On. This is normal; there is nothing wrong with the TV. Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they have no adverse effect on the TV’s performance. Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may produce some temporary distortion effects on the screen.
4 |
206-4213 |
Table of Contents
Safety Warnings . . . . . . . . . . . . . . . . . 2 Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . . 3 – 4 Table of Contents . . . . . . . . . . . . . . . . 5 Commercial Mode Overview . . . . . . . . . . . 6 – 8 Setup Checklist . . . . . . . . . . . . . . . . 6 Pass-through Mode . . . . . . . . . . . . . . . 6 FTG Mode . . . . . . . . . . . . . . . . . . 8 Remote Management in FTG Mode . . . . . . . . 8 Pro:Centric Operation . . . . . . . . . . . . . 9 – 10 Pro:Centric TV Interactive Menu Features . . . . . . 9 Pro:Centric Interactive Menu Navigation . . . . . . . 9 Pro:Centric Setup . . . . . . . . . . . . . . . 10
Automated Installation Routine Wizard . . . . . 11 – 13 Pro:Centric Auto Configuration . . . . . . . . . . 11 Pro:Centric Manual Configuration . . . . . . . . . 12 USB Configuration . . . . . . . . . . . . . . . 13
Custom Master TV Setup . . . . . . . . . . 14 – 17 Before You Begin . . . . . . . . . . . . . . . 14 Cloning Methods . . . . . . . . . . . . . . . 14 Clonable TV Setup Menu Features . . . . . . . . 14 Custom Master TV Setup Procedure . . . . . . . . 15
Installer Menu . . . . . . . . . . . . . . . 18 – 26 Accessing the Installer Menu . . . . . . . . . . . 18 Using the Installer Menu . . . . . . . . . . . . 19 Exiting the Installer Menu and Activating Updates . . 19
Channel Icons / Custom Text Labels
(2-5-4 + MENU Mode) . . . . . . . . . . . . . . 27 Cloning Overview . . . . . . . . . . . . . . . 28
USB Cloning Procedures . . . . . . . . . . . 29 – 32
Learning / Teaching a Master TV Setup using
a USB Memory Device / .tlx File . . . . . . . . . 29
Learning / Teaching a Master TV Setup using
a USB Memory Device / .tll File . . . . . . . . . . 31
Clone Programmer Cloning Procedures . . . . . 33 – 36
Learning / Teaching a Master TV Setup using
a TLL-1100A Clone Programmer . . . . . . . . . 33
Learning / Teaching a Master TV Setup using
an LT2002 Clone Programmer . . . . . . . . . . 35
FTG Mode of Operation Overview . . . . . . . 37 – 38 FTG Mode via CPU or EBL . . . . . . . . . . . 37 Determining the TV Operating Mode . . . . . . . . 38
FTG Mode via CPU . . . . . . . . . . . . . 39 – 43
Creating an FTG Configuration File using the
FTG File Manager . . . . . . . . . . . . . . . 39 Teaching FTG Configuration to a TV . . . . . . . . 41 Learning an FTG Configuration File from a TV . . . . 42 Optional Manual Configuration / TV Setup . . . . . 43
FTG Mode via EBL (Local Configuration) . . . . . . 44 FTG File Manager Utilities Overview . . . . . . . 45 – 48 FTG File Manager Main Screen . . . . . . . . . 45 FTG Channel Map Configuration Utility . . . . . . . 46 FTG Channel Map Editor . . . . . . . . . . . . 47 FTG Installer Menu Configuration Utility . . . . . . 48 Remote Jack Pack / TV Connections & Setup . . . . . 49
References
Upgrading TV/PTC Software using a USB Memory
Device . . . . . . . . . . . . . . . . . . . . 50
Downloading a Splash Screen using a USB Memory
Device . . . . . . . . . . . . . . . . . . . . 51 Power Consumption Settings . . . . . . . . . . . 52 TV Aux Input Configuration . . . . . . . . . . . . 53 b-LAN Setup & Overview . . . . . . . . . . . . . 54 RJP Model List & Input Auto-sensing Hierarchy . . . . 55 Restoring Factory Defaults on the TV(s) . . . . . . . 56 TV Zone Restrictions . . . . . . . . . . . . . . . 57 LT670H Rear and Side Jack Panels . . . . . . . . . 58 Installer Remote Control Typical Key Functions . . . . 59
Troubleshooting . . . . . . . . . . . . . . . 60 – 63 General Troubleshooting . . . . . . . . . . . . 60 Troubleshooting Flow Chart . . . . . . . . . . . 61
Commercial Mode Check / FTG Operation Troubleshooting . . . . . . . . . . . . . . . . 62
Clone Programmer Troubleshooting . . . . . . . . 63 Glossary of Terms . . . . . . . . . . . . . . . . 64
Document Revision History / Open Source Software Notice 65 Back Cover . . . . . . . . . . . . . . . . . . 66
Notes
•Installer Menu content is intended for use primarily by qualified TV electronics technicians.
•Refer to the Quick Reference Guide for additional information on TV installation, features, specifications, maintenance, and safety instructions.
•Design and specifications subject to change without prior notice.
206-4213 |
5 |
Commercial Mode Overview
This document describes how to set up LT670H Pro:Centric™ TVs for Commercial Mode operation. LG commercial TV functionality is based on “ownership” of the Channel Map; that is, the Channel Map resides in the TV’s CPU, Protocol Translator Card (PTC), or embedded b-LAN™ (EBL) module, or it resides externally from the TV (i.e., in a device from the solution provider).
These TV models are capable of Free-To-Guest (FTG) Mode operation via the TV CPU. Alternatively, the EBL module can be configured either for Pass-through Mode (default) or FTG Mode. When neither the CPU nor EBL is in FTG Mode, these TV models also allow external control via the TV’s MPI port.
Setup Checklist
Note: This document provides information specific to Commercial Mode operation. Refer to the Owner’s Manual for detailed information on TV installation and hardware and cable connections.
Installation
__ Unpack TV and all accessories.
__ Install batteries in the Installer Remote. __ Install TV on VESA mount or stand.
Note: It may be advisable to make all cable connections before installing on VESA mount or stand, as appropriate.
Hardware Connections
__ Install any additional hardware as appropriate to your institution, LAN, etc.
Pass-through Mode
Cable Connections
__ Make all rear jack panel and MPI card slot connections, as appropriate.
Commercial Mode Setup
__ Complete appropriate procedures as described in this document for Commercial Mode operation.
This mode allows you to configure individual TVs for Pro:Centric or FTG Mode via CPU operation and/ or create a Master TV Setup for cloning purposes for TVs that are to remain in Pass-through Mode. This mode also allows external control via the GAME CONTROL/MPI port on the TV rear jack panel.
There are two methods for configuring individual TVs that are currently in Pass-through Mode: either using the Automated Installation Routine Wizard or the Custom Master TV Setup procedure as described in this document.
Automated Installation Routine Wizard
The Automated Installation Routine Wizard provides Auto or Manual options for configuring essential items for Pro:Centric operation and also provides an option for using a USB memory device to configure the TV for FTG Mode via CPU. Use the Installer Remote to make selections and complete each step. See “Automated Installation Routine Wizard” on pages 11 to 13 for detailed information.
Custom Master TV Setup
The Custom Master TV Setup procedure enables you to create a customized Master TV Setup for cloning purposes. Use the Installer Remote to configure Installer Menu items as required for TV operation and set up TV features (Channel, Picture, Audio, etc.). See “Custom Master TV Setup” on pages 14 to 17 for detailed information.
6 |
206-4213 |
Commercial Mode Overview (Cont.)
Installer Menu
To create a Master TV Setup, you will need to know how to access the commercial controller (PTC) Installer Menu and make changes to the default values as required. If necessary, familiarize yourself with the Installer Menu and how to make and save changes. Refer to pages 18 to 26 for information on accessing the Installer Menu and for detailed descriptions of the Installer Menu items.
xxLT670H PTC INSTALLER MENU CPU-CTV
000 INSTALLER SEQ 000
TV Setup Menus
On-screen setup menus control the features of the TV. Use the Installer Remote to access the TV setup menus, and set the TV features to the desired configuration for the end user.
Cloning
Cloning refers to the process of capturing a Master TV Setup and transferring it to a Target TV— both TVs must be in Pass-through Mode and both TVs must be identical models. The Master TV’s clonable setup menu features should be configured as part of the Master TV Setup. If there are features in the Master TV’s setup—channel icons or labels, digital font options, etc.—that are not set or that are set incorrectly, those features also will not be set or will be set incorrectly in the Target TVs. Refer to pages 28 to 36 for detailed information on cloning requirements and procedures.
UPN |
000-000-000-000 |
ASIC D279 |
PTC |
V1.00.009 |
CPU V3.17.00 |
|
|
|
Typical Installer Menu
PICTURE |
AUDIO |
CHANNEL |
TIME |
LOCK |
OPTION |
INPUT |
MY MEDIA |
TV Setup Menus
External MPI Control
To control the TV using an external MPI control device, you must use the TV’s GAME CONTROL/MPI port for communication purposes. In these TVs, Installer Menu item 118 POWER SAVINGS controls the power circuitry for both the embedded b-LAN module and the GAME CONTROL/MPI port; therefore, to ensure that the GAME CONTROL/MPI port circuitry is powered, thus enabling MPI communication, Installer Menu item 118 POWER SAVINGS must be set appropriately. See Installer Menu item descriptions as well as Reference section, “b-LAN Setup & Overview,” for further information.
Note: These TV models are not equipped with MPI card slots.
206-4213 |
7 |
Commercial Mode Overview (Cont.)
FTG Mode
This mode enables Pro:Idiom ® decryption and also allows logical channel mapping of physical channels to remove the need for dash tuning. TV operation in FTG Mode is based on which element of the TV owns the FTG Logical Channel Map—the CPU or the EBL. Understanding the application in which the TV will be used is vital in determining the owner.
As indicated above, FTG mode operation in the LT670H models can be provided either by the TV CPU or EBL. These are two separate and distinct FTG Modes of operation, each with its own unique advantages and requirements as described later in this document. When the TV CPU is configured with an FTG Channel Map, the CPU controls the operation of the TV, and when the EBL is configured with an FTG Channel Map, the EBL controls the operation of the TV.
Once it is determined whether the TV CPU or the EBL will own the FTG Channel Map, configuration can begin. Configuration of either requires a PC application—the LG FTG File Manager for the TV CPU or the LG FTG Device Configuration Application for the EBL. Each application provides utilities that enable you to create/edit an FTG Channel Map and configure Installer Menu settings. See pages 37 to 48 for further information on FTG Mode operation and configuration.
Remote Management in FTG Mode
When the TV is configured for FTG Mode via CPU, remote management of the FTG Channel Map and FTG Installer Menu settings is provided by a Pro:Centric server. Refer to the Pro:Centric™ Server Admin Client User Guide for further information.
When the TV is configured for FTG Mode via EBL, the b-LAN module, which is internal to the TV, allows hotel/institution head end equipment (for example, an FMA-LG101) with b-LAN technology to communicate with the TV to provide remote management of the FTG Channel Map and FTG Installer Menu settings. See Reference section, “b-LAN Setup & Overview,” for further information.
8 |
206-4213 |
Pro:Centric Operation
Pro:Centric TV Interactive Menu Features
When running the Pro:Centric application, the interactive Pro:Centric TV enables guests to locate and select television entertainment using an interactive channel guide, check the daily weather, and view hotel and surrounding amenities via custom billboards and points-of-interest maps.
Pro:Centric application features include:
•Portal and information screens/pages (including a “Welcome” page) that include branding logos.
•An optional customized user interface (custom “skins”).
•Billboards and points-of-interest maps that can be customized to focus on hotel amenities, local attractions and businesses, restaurants, news, events, etc.
•An optional Weather billboard that includes a local radar map, current conditions, and a four day forecast.
•An interactive channel guide that provides a channel list with channel icons. An electronic program guide (EPG) is an optional feature that displays up to three days of programming information viewable by channel and time.
•Video spooling that enables the hotel to deliver a video file to guest TVs for promotion and information purposes.
The Pro:Centric server Admin Client web editor/content wizard is provided for customer configuration of portal messages and billboards/maps.
Note: Customized content is typically defined by the service integrator and/or hotel administrators. LG does not provide hotel-specific content.
Pro:Centric Interactive Menu Navigation
Use the Pro:Centric TV remote control to operate both interactive menus and regular TV features. Press PORTAL on the remote to access the interactive menus.
Note: Interactive menu options may vary, depending on Pro:Centric features enabled for the site. The following are default interactive menus.
Channel Guide
Shows available TV networks and logical channels. When available, EPG data provides additional channel and program information.
Information
Typically displays information on hotel amenities, for example, restaurants, in-room dining, business centers, facilities, etc., as well as information on local weather and attractions.
Help
Provides help for navigating the interactive menus.
Watch TV
Removes the interactive menu from the screen and returns to the previously tuned TV channel.
206-4213 |
9 |
Pro:Centric Operation (Cont.)
Pro:Centric Setup
Administration and management options for the Pro:Centric server are described in detail in the Pro:Centric™ Server Admin Client User Guide. This document describes only those settings that must be specified on the TVs.
On the TVs, the Data Channel must be set appropriately to enable Pro:Centric remote management/ administration facilities, while the Pro:Centric Application Mode must be set appropriately to enable the Pro:Centric application.
•Remote management/administration (TV E-Z Installation): The Pro:Centric server Admin Client provides remote management/administration facilities for downloading splash screens and software/firmware updates as well as facilities for downloading the FTG Channel Map and FTG Installer Menu settings for TVs that are in FTG Mode via CPU.
•Pro:Centric application: The application, which operates in conjunction with FTG and PPV Modes, comprises the Pro:Centric interactive menus/features described on the previous page. Pro:Centric application settings are managed via the Pro:Centric Admin Client.
The Data Channel and Pro:Centric Application Mode can be set using one of the following methods:
•When the TV is in a factory default state, the Automated Installation Routine Wizard provides Auto or Manual options for configuring both the Data Channel and the Pro:Centric Application Mode.
The Automated Installation Routine Wizard also provides a USB Configuration option that enables you to configure a TV for FTG Mode via CPU using an FTG Configuration (.tlx) file stored on a USB memory device. The FTG Configuration file incorporates FTG Installer Menu settings, which includes Installer Menu items 098 PRO:CENTRIC and 119 DATA CHANNEL.
Refer to “Automated Installation Routine Wizard” on pages 11 to 13 for further information on the Automated Installation Routine Wizard options.
•If the TV is in Pass-through Mode, set Installer Menu items 098 PRO:CENTRIC and 119 DATA CHANNEL) to the appropriate values. Refer to “Installer Menu” information on pages 18 to 26 for further information. Also, as necessary, refer to “Custom Master TV Setup” information on pages 14 to 17 and/or cloning information on pages 28 to 36.
•If the TV is in FTG Mode (via CPU or EBL), use the appropriate software to update Installer Menu items 098 PRO:CENTRIC and 119 DATA CHANNEL and then transfer the FTG Installer Menu settings to the TV in accordance with the FTG Mode of configuration. Refer to FTG Mode information on pages 37 to 48 for further information.
10 |
206-4213 |
Automated Installation Routine Wizard
The Automated Installation Routine Wizard will appear on |
|
|
|
|
|
|
|
Welcome |
|
|
Move OK |
|
|
the screen each time the TV is turned ON, until one of its |
|
|
|
|
|
|
configuration methods has been completed or the wizard is |
|
|
Please select configuration method. |
|
||
exited. The wizard’s Welcome screen provides a selection of |
|
|
|
|
|
|
configuration methods: Auto or Manual options for configuring |
|
|
|
Pro:Centric Auto |
|
|
essential items for Pro:Centric operation and also an option |
|
|
|
Pro:Centric Manual |
|
|
for using a USB memory device to configure the TV for FTG |
|
|
|
USB Configuration |
|
|
Mode via CPU. This section describes each of the Automated |
|
|
|
Exit |
|
|
Installation Routine Wizard options. |
|
|
|
|
|
|
Note: If it has been completed or exited and therefore does not |
|
|
|
|
|
|
display, the Automated Installation Routine Wizard can be re-activated; |
|
|
|
|
|
|
however, this requires that factory defaults be restored on the TV(s). |
|
|
|
|
|
|
Refer to Reference section, “Restoring Factory Defaults on the TV(s),” |
|
|
|
|
|
|
for further information. |
|
|
|
|
|
|
Note: If you plan to create a Master TV Setup using the procedure on pages 14 to 17, be sure to exit the Automated Installation Routine Wizard in order to avoid setting modes that may restrict the custom setup procedure.
Note: If any of the configuration steps fails, you will see an “Incomplete” screen with an indication of the failure. You will then have the opportunity to reinitiate the current configuration process, select another configuration method (for example to select Pro:Centric Manual instead of Auto configuration), or exit the Automated Installation Routine Wizard.
Caution: Do NOT unplug the TV power cord or remove the antenna cable during any of the configuration processes, as doing so will interrupt the current step and may corrupt the configuration data.
To exit the Automated Installation Routine Wizard, use the Up/Down arrow keys on the Installer Remote to select/highlight Exit. Then, press OK.
Pro:Centric Auto Configuration
When selected, this option enables the TV to use a search algorithm to automatically determine the type of Pro:Centric network, the Data Channel, and the Pro:Centric Application Mode. The TV then looks for the Pro:Centric application and maintenance (E-Z Installation) files to download.
Note: If you intend to use the Pro:Centric server for remote management only of E-Z Installation (splash screen, configuration, or firmware) data downloads, use the “Pro:Centric Manual” option described on the following page.
Use the Up/Down arrow keys on the Installer Remote to select/ highlight Pro:Centric Auto from the Automated Installation Routine Wizard Welcome screen. Then, press OK.
The Pro:Centric Auto Configuration will proceed with a series of automated steps to configure the TV for Pro:Centric operation and to download the Pro:Centric application and E-Z Installation data. The Auto Configuration screen (see example at right) shows overall progress, as well as the progress and/or values for each of the individual installation steps. Note that some steps may require up to 15 minutes.
When the Pro:Centric Auto Configuration is complete, the wizard exits, and the TV will turn OFF.
|
Auto Configuration |
|
|
|
Prev. |
|
|
|
|
|
|
Processing Pro:Centric Configuration. |
|
|
|
|
|
|
|
|
Step 2 may take up to 15 min(s). |
|
|
|
|
|
|
|
|
Please wait... |
|
|
|
|
|
|
|
|
|
|
10% |
|
|
|
|
|
Step 1 |
Detecting the type of Pro:Centric network |
: |
RF |
|
||
|
|
Step 2 |
Locating the Pro:Centric Server |
: |
In Progress |
|
||
|
|
Step 3 |
Determining the Pro:Centric mode |
: |
|
|
|
|
|
|
Step 4 |
Downloading the application files |
: |
|
|
|
|
|
|
Step 5 |
Downloading the maintenance files |
: |
|
|
|
|
|
|
Step 6 |
Saving the Pro:Centric confiugration |
: |
|
|
|
|
Warning - Do not remove AC power or the signal cables during these steps
206-4213 |
11 |
Automated Installation Routine Wizard (Cont.)
Pro:Centric Manual Configuration
If you already know the required Data Channel and Pro:Centric Application Mode settings for the TV, you may streamline the setup process by entering this data manually.
1.Use the Up/Down arrow keys on the Installer Remote to select/highlight Pro:Centric Manual from the Automated Installation Routine Wizard Welcome screen. Then, press
OK.
2.The first Manual Configuration Screen (see example at right) enables you to specify the following data:
•Pro:Centric Mode: Use the Left/Right arrow keys to select the appropriate Pro:Centric Application Mode (GEM, FLASH, or Configuration Only).
•Channel Number: Either directly enter or use the Left/Right arrow keys to select the Data Channel.
Note: For remote management only, select the Pro:Centric Mode “Configuration Only” option to search for TV E-Z Installation (splash screen, configuration, or firmware) data downloads. Pro:Centric application data will not be downloaded.
Note: Select the “Back” button from the Manual Configuration screen or press the
key on the Installer Remote, if desired, to return to the Welcome screen.
3.Once you have specified the data as indicated above, you have two options:
•To save the data entered and exit the wizard, use the arrow keys to select Save and Exit, and then press OK. The Pro:Centric application and/or E-Z Installation data will be downloaded to the TV at a later time. This option is useful, in particular, if the Pro:Centric server is not yet set up.
•To initiate a real-time download of Pro:Centric application and/or E-Z Installation data, use the arrow keys to select Next, and then press OK.
Note: Signal must be detected on the Data Channel from the Pro:Centric server in order for you to select “Next” (you should see a “Data Channel found” message below the signal strength indicator).
The Pro:Centric Manual Configuration will proceed with the remaining Pro:Centric application and/or E-Z Installation data download steps, as shown on the second Manual Configuration screen (see example at right). When the Pro:Centric Manual Configuration is complete, the wizard exits, and the TV will turn OFF.
|
Manual Configuration |
|
|
|
|
Move OK |
Prev. |
|
|||
|
|
Pro:Centric Mode |
< |
GEM |
> |
|
|
|
|||
|
|
Channel Number |
|
|
1 |
|
|
|
|
|
|
|
|
Signal Strength |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
0% |
|
|
||||
|
|
|
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
||
|
|
BACK |
|
Save and Exit |
|
|
NEXT |
|
|
||
|
|
|
|
|
|
|
|
|
|
|
|
|
Manual Configuration |
|
|
Prev. |
|
|
||||
|
|
|
|
Processing Pro:Centric Configuration. |
|
|
|
|
||
|
|
|
|
Step 4 may take up to 5 min(s). |
|
|
|
|
|
|
|
|
|
|
Please wait... |
|
|
|
|
|
|
|
|
|
|
|
|
|
50% |
|
|
|
|
Step 1 |
Detecting the type of Pro:Centric network |
: |
RF |
|
|||||
|
Step 2 |
Locating the Pro:Centric Server |
: |
DIGITAL 75 |
|
|||||
|
Step 3 |
Determining the Pro:Centric mode |
: |
GEM |
|
|||||
|
Step 4 |
Downloading the application files |
: |
In Progress |
|
|||||
|
Step 5 |
Downloading the maintenance files |
: |
|
|
|
|
|||
|
Step 6 |
Saving the Pro:Centric confiugration |
: |
|
|
|
|
|||
Warning - Do not remove AC power or the signal cables during these steps
12 |
206-4213 |
Automated Installation Routine Wizard (Cont.)
USB Configuration
This section describes how to configure a TV for FTG Mode via CPU operation using an FTG Configuration (.tlx) file loaded on a USB memory device.
Note: Refer to the Free-To-Guest (FTG) File Manager User Guide and/or “Creating an FTG Configuration File using the FTG File Manager” on pages 39 to 40 for information on creating an FTG Configuration (.tlx) file.
Note: This procedure assumes that the FTG Configuration file contains an FTG Channel Map. If not, any Installer Menu and/or TV setup menu settings contained in the file will be transferred to the TV (as with typical cloning); however, the TV will remain in Pass-through Mode and will not be configured for FTG Mode via CPU.
1.Plug the USB memory device that contains the FTG Configuration (.tlx) file into the Target LT670H TV USB IN port.
2.Use the Up/Down arrow keys on the Installer Remote to select/highlight USB Configuration from the Automated Installation Routine Wizard Welcome screen. Then, press OK.
3.In the Accessing USB Storage Device window, use the Up/ Down arrow keys to select the FTG Configuration file you wish to use to configure this TV, and then press OK.
The TV will show configuration progress in a new window. Do NOT remove the USB device until configuration is complete. When the configuration is complete, the TV will briefly display a “Complete” window and then exit the Automated Installation Routine Wizard.
4.Remove the USB memory device, and verify that the FTG Configuration is resident on the Target TV.
The Target TV CPU is now in FTG Mode.
Note: After the configuration process is complete, the TV tunes according to the Start Channel setting in the Installer Menu. If a Start Channel is specified, the TV will tune to that channel; otherwise, the TV will tune to the lowest logical channel in the FTG Channel Map.
Accessing USB Storage Device |
Move |
OK |
Prev. |
Please select configuration file (*.tlx)
xxLT670H-UA00005.TLX
USB Configuration
Configuring TV
Please wait... |
95% |
|||
|
|
|
|
|
|
|
|
|
|
Warning - Do not remove the USB device during this process
206-4213 |
13 |
Custom Master TV Setup
This section describes how to create a customized Master TV Setup for cloning purposes when the TV is in Pass-through Mode.
Note: Refer to FTG Mode information on pages 37 to 48 for details on entering FTG Mode and configuring/ editing the FTG Channel Map and FTG Installer Menu settings.
Note: Cloning requirements and procedures are described in detail on pages 28 to 36.
Before You Begin
•It is recommended that you disconnect all Aux inputs if you intend to run Auto Tuning (Channel Search). Under certain conditions, Auto Tuning is disabled if there is an Aux input active.
•Determine which cloning tool—USB memory device or clone programmer—is appropriate for your application; several of the Master TV Setup procedure steps are dependent on the cloning tool to be used. See “Cloning Methods” at right for further information.
•If you intend to use a USB memory device, determine the type of file—either the new “.tlx” file format or the legacy “.tll” file format—to use for cloning purposes; several of the Master TV Setup procedure steps are dependent on the desired file type. See “Cloning Methods” at right for further information.
•If the Automated Installation Routine Wizard appears on the screen, exit the wizard before beginning/continuing the Custom Master TV Setup procedure.
Cloning Methods
See also “Clonable TV Setup Menu Features” list below.
Using a USB Memory Device / .tlx File
•The .tlx file format clones Installer Menu settings and all TV sources’ (analog, digital, AV1, HDMI, etc.) clonable setup menu settings.
•Not intended for cloning an auto-tuned/edited Channel Map, as the channel lineup is converted to a logical FTG Channel Map when saved (Learned) from a TV to a .tlx file. If the .tlx file with the FTG Channel Map is then used for Teaching purposes, all Target TVs will be configured for FTG Mode via CPU.
Using a USB Memory Device / .tll File
The .tll file format clones the contents of the commercial controller (PTC) memory, including an auto-tuned/edited Channel Map, Installer Menu settings, and one TV source’s (analog, digital, or Aux) clonable setup menu settings.
Using a Clone Programmer (TLL-1100A or LT2002)
Both the TLL-1100A and LT2002 clone the contents of the commercial controller (PTC) memory, including an auto-tuned/ edited Channel Map, Installer Menu settings, and one TV source’s (analog or Aux) clonable setup menu settings.
Clonable TV Setup Menu Features
Channel |
Audio |
Option |
Auto Tuning (Channel Lineup) |
Auto Volume |
Menu Language |
Manual Tuning |
Clear Voice |
Audio Language |
Channel Edit |
Sound Mode |
Caption |
Channel Label |
Balance |
Lock |
Picture |
TV Speaker |
|
Time |
Movie Rating |
|
Picture Mode |
TV Rating – Children |
|
|
Auto Clock |
TV Rating – General |
|
Auto Off (Sleep Timer) |
|
|
|
|
Note: Some menu options vary between analog and digital channels and Aux inputs.
14 |
206-4213 |
Custom Master TV Setup (Cont.)
Custom Master TV Setup Procedure
1.Turn ON the TV.
If the Automated Installation Routine Wizard appears on the screen when you turn ON the TV, use the Up/Down arrow keys on the Installer Remote to select Exit from the Welcome screen, and press OK to exit the wizard.
2.Set Installer Menu items.
This step provides specific instruction only on the Installer Menu items
that should be set on a Master TV. Refer to pages 18 to 26 for detailed |
|
|
|
|
|
|
|
|||
|
|
xxLT670H PTC INSTALLER MENU |
|
|
||||||
information on all Installer Menu items. |
|
|
|
|
||||||
|
|
|
CPU-CTV |
|
|
|
||||
a) |
Use the Installer Remote to access the PTC Installer Menu (see |
|
|
|
|
|
|
|
||
|
“Accessing the Installer Menu” on page 18 for further information). |
|
|
000 |
INSTALLER SEQ |
000 |
|
|
||
|
The next step depends on whether the Automated Installation |
|
|
|
|
|
|
|
||
|
Routine Wizard appeared when you turned ON the TV: |
|
|
|
|
|
|
|
||
|
|
|
UPN 000-000-000-000 |
ASIC D279 |
|
|
||||
|
• |
If the wizard did appear, the TV is in a factory default state, and |
|
|
|
|
||||
|
|
|
PTC |
V1.00.009 |
CPU V3.17.00 |
|
|
|||
|
|
you can proceed to set Installer Menu items. Go to step (c). |
|
|
|
|
|
|
|
|
|
• |
If the wizard did not appear, go to step (b). |
|
|
|
Typical Installer Menu |
||||
b) |
Set Installer Menu item 117 FACT DEFAULT to 001 and press |
|
|
|
||||||
Note: The Installer Menu header will vary |
||||||||||
|
OK on the Installer Remote. |
|||||||||
|
depending on the TV you are setting up. |
|||||||||
|
This clears all Installer Menu custom settings, channel lineup, etc. |
|||||||||
|
|
|
|
|
|
|
|
|||
|
and restores the factory default settings. The value will change |
|
|
|
|
|
|
|
||
|
|
117 |
FACT DEFAULT |
000 |
|
|
||||
|
back to 0 after the PTC has been restored to factory default |
|
|
|
||||||
|
|
|
|
|
|
|
|
|||
|
condition. This step ensures that the TV Channel Memory will be |
|
|
|
|
|
|
|||
|
|
003 |
BAND/AFC |
001 |
|
|
||||
|
the active channel lineup. |
|
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|||
c) Set Installer Menu item 003 BAND/AFC, as appropriate.
• Broadcast: Set to 000. |
• HRC: Set to 002. |
Adjust the values for these Installer Menu items, as required.
• CATV: Set to 001 (default). |
• IRC: Set to 003. |
d)Set any other Installer Menu items that affect your TV programming network to the required configuration. For example, enable/disable Aux inputs, set a Start Channel, etc.
e)After you have adjusted all Installer Menu item settings as required, press OK once on the Installer Remote to save your changes; then, press OK again to exit the menu.
Note: If you performed step (b) above to restore factory defaults, the Automated Installation Routine Wizard will re-activate as soon as you exit the Installer Menu. Exit the wizard (see step 1), and then continue with step 3.
3.Set up TV features.
On-screen setup menus control the features of the TV. Press MENU SETTINGS on the Installer Remote to access the TV setup menus, and then set Channel, Picture, Audio, Lock, Time, etc. options to the desired configurations. See “Clonable TV Setup Menu Features” list on previous page and also notes on the following page.
PICTURE |
AUDIO |
CHANNEL |
TIME |
LOCK |
OPTION |
INPUT |
MY MEDIA |
Use the TV setup menus to set the TV features to the desired configuration for the end user.
(Continued on next page)
206-4213 |
15 |
Custom Master TV Setup (Cont.)
(Continued from previous page)
Note: If you intend to clone the PTC, remember that only one TV source’s clonable setup menu settings will be cloned. Thus, for a clone programmer, the TV setup menu settings should be applicable to either an analog channel or Aux input, while for a USB device / .tll file, the TV setup menu settings should be applicable to the analog or digital channel or Aux input to which the Target TV will be set during the Teaching process.
Note: If desired and if appropriate depending on the cloning method to be used (see “Cloning Methods” on page 14), you can run Auto Tuning (see step 4) prior to completing this step.
4. (Optional) Run Auto Tuning.
Note: If you intend to use a USB memory device / .tlx file for cloning purposes, DO NOT run Auto Tuning. If you
Teach a .tlx file with an auto-tuned/edited Channel Map to a Target TV, this will put the Target TV in FTG Mode via CPU. Proceed to step 6 to verify the TV setup. (Steps 5 and 6 are not applicable for .tlx files.)
If you run Auto Tuning with the intention to clone the resulting Channel Map, you must use a USB memory device / .tll file or a clone programmer for this cloning purpose.
a)To search for all available analog and digital channels, go to the Channel Menu, select the Auto Tuning option, and follow the on-screen instructions.
b)Use the Channel Edit option in the Channel Menu to edit the channel lineup, as necessary, to include only free to guest (nonencrypted) channels.
•Add/delete channels per your system requirements.
•Use the Channel Label option in the Channel Menu to select the appropriate trademark/icon for each channel’s Channel-Time on-screen display. Icons are available for familiar channels, such as ABC, CBS, NBC, etc. Identifiable labels (icons) should enable the end user to readily know what common networks are available.
Note: If you intend to clone the PTC and Installer Menu item 103 ATSC TUNE MODE is set for Physical Channel tuning (default and recommended setting), channels with minor channel numbers higher than 255 will not transfer correctly in step 5. If item 103 is set for Virtual Channel tuning and either the major or minor channel numbers are higher than 255, the channel(s) will not transfer correctly in step 5.
Note: If you intend to clone the PTC, you can add the channel icons in this step or as described in step 6. Also in step 6, you can add custom text labels for channels without icons.
CHANNEL |
Move |
OK |
• Auto Tuning |
|
|
• Manual Tuning |
|
|
• Channel Edit |
|
|
• Channel Label |
|
|
(Optional) Use Channel Menu options to run Auto Tuning, edit channels, and select channel icons.
(Continued on next page)
16 |
206-4213 |
Custom Master TV Setup (Cont.)
(Continued from previous page)
5.Transfer the TV setup menu settings to the commercial controller (PTC): 2-5-5 + MENU Mode
Note: This step is essential for successful cloning using a USB memory device /
.tll file or a clone programmer. Without this step, the PTC will not contain any of the TV setup menu settings.
Note: The maximum number of channels (analog, digital, and Aux inputs) that can be transferred to the PTC is 141. An attempt to transfer more than 141 channels of any combination will result in a Channel Map of exactly 141 channels; any extra channels will not be available in the PTC Channel Map. For example, if you enabled three Aux inputs in the Installer Menu and Auto Tuning found 141 channels, you must edit the Channel Map to decrease the number of analog/digital channels to (at most) 138.
a)After the TV channel lineup has been edited and channel label icons added, tune to the channel (source) for which you wish to transfer TV setup menu settings.
Note: If you intend to use a clone programmer for cloning purposes, this must be either an analog channel or Aux input.
b)Access the Installer Menu, and press 2-5-5 + MENU SETTINGS on the Installer Remote to initiate the transfer of the Master TV Setup to the PTC. The TV exits the Installer Menu and then tunes through the channels in the channel lineup during the transfer. When the transfer is complete, the TV tunes back to the channel that was tuned before the transfer began.
6.(Optional) Add Custom Channel and Aux Input Labels: 2-5-4 + MENU Mode
Note: 2-5-4 + MENU Mode enables you to add/edit channel icons and custom text labels in the PTC once the Master TV Setup has been transferred as described in the previous step.
Access the Installer Menu, and press 2-5-4 + MENU SETTINGS on the Installer Remote. Add/edit custom text labels and/or change icons for the Channel-Time on-screen displays (see 2-5-4 + MENU procedural information on page 27). Note that broadcast digital channels often already have a broadcaster generated label. When you are finished, press MENU SETTINGS to exit 2-5-4 + MENU Mode.
7.Verify the TV setup.
As applicable, verify that the channel lineup, channel icons, and custom text labels are correct. Also, make sure the TV features are set per your requirements.
8.(Recommended) Lock the channel lineup.
Access the Installer Menu. Set item 028 CH. OVERIDE to 000 and press OK to lock the channel lineup and restrict access to the TV setup menus. Press OK again to save your changes and exit the Installer Menu.*
The Master TV Setup is now ready to be copied to the predetermined cloning tool—a USB memory device (.tlx or .tll file) or a clone programmer. See cloning procedures in this document.
DIGITAL 19-3
MONO STEREO SAP
WXYZ
Custom text label “WXYZ” created in 2-5-4 + MENU Mode.
028 CH. OVERIDE |
000 |
After verifying the TV Setup, set Installer Menu item 028 CH. OVERIDE to 000.*
* This step prevents end users from accessing channel settings (i.e., the Channel Menu will be inaccessible/ grayed out).
206-4213 |
17 |
Installer Menu
Use the Installer Menu to set up, change, or view operational settings. Refer to the table starting on the next page for brief descriptions of Installer Menu items. More detailed descriptions follow the table listing.
Accessing the Installer Menu
1.Turn ON the TV.
If the Automated Installation Routine Wizard appears on the screen when you turn ON the TV, use the Up/Down arrow keys on the Installer Remote to select Exit from the Welcome screen, and press OK to exit the wizard.
xxLT670H PTC INSTALLER MENU CPU-CTV
2. Using an Installer Remote, press MENU SETTINGS repeatedly |
|
|
|
|
|
|
000 |
INSTALLER SEQ |
000 |
|
|
until the on-screen display of the TV setup menus (if the TV is |
|
|
|
|
|
in Pass-through Mode) or the Function Menu (if the TV is not in |
|
|
|
|
|
Pass-through Mode) no longer toggles, and then press the |
|
|
|
|
|
UPN |
000-000-000-000 |
ASIC D279 |
|
||
Installer Menu entry sequence (e.g., 9-8-7-6) + OK to access the |
|
||||
PTC |
V1.00.009 |
CPU V3.17.00 |
|
||
Installer Menu. |
|
|
|
|
|
|
|
|
|
||
Note: The default Installer Menu entry sequence is “9876”; |
|
Typical Installer Menu |
|
||
however, if Installer Menu item 000 INSTALLER SEQUENCE |
|
|
|||
has been modified, the entry sequence may be one of three additional options. See Installer Menu detailed descriptions for further information.
The Installer Menu opens with item 000 INSTALLER SEQ 000.
Note: If the password (entry sequence) is not entered or registered correctly, you will see the message “ENTER PASSWORD 0000” at the top of the screen instead of the Installer Menu header. Once you re-enter the correct password (e.g., press 9-8-7-6 + OK), the Installer Menu will display.
Note: If the TV is not in Pass-through Mode, the Installer Menu is accessible as read-only.
As part of the Installer Menu header, two 3-character acronyms are displayed to indicate the TV’s current configuration mode. The table below lists all possible mode identifiers for these TV models.
Acronym |
Description |
CPU-CTV |
Pass-through Mode with Channel Map in CPU |
CPU-FTG |
FTG Mode via CPU |
EBL-FTG |
FTG Mode via EBL |
EBL-LNT |
LodgeNet PPV Mode |
MPI-EXT |
External MPI Control |
PTC-CTV |
Pass-through Mode with Channel Map in PTC |
|
|
18 |
206-4213 |
Installer Menu (Cont.)
Using the Installer Menu
Refer to the table on pages 20 and 21 for an overview of the available Installer Menu items, including their item numbers, functions, value ranges, and default values.
Installer Menu items not relevant to these TV models are not present in the Installer Menu; therefore, some numbers are missing. For example, item 006 will not appear. In addition, items that are dependent on other Installer Menu item settings will not be initially accessible. For example, item 046 STRT AUX SRCE will not display in the Installer Menu unless item 004 STRT CHANNEL is set to 0.
Navigation within the Installer Menu
Use the Up/Down arrow keys on the Installer Remote to sequence through the available menu items, or access an item directly by keying in the item number and then pressing MENU SETTINGS. For example, to access the SLEEP TIMER option, which is item 015, press 0-1-5 + MENU.
Changing Installer Menu Settings
To change an Installer Menu item value, use the Left/Right arrow keys on the Installer Remote, or enter a valid value directly. To save the new setting, press OK, or use the Up/Down arrow keys to navigate to a new Installer Menu item if you have additional items to edit. Note that invalid values will not be saved.
Exiting the Installer Menu and Activating Updates
After you have adjusted all required Installer Menu item settings, press OK once on the Installer Remote to save your changes; then, press OK again to exit the Installer Menu. Any changes you make will be stored in non-volatile memory.
Note: Each time you exit the Installer Menu in Pass-through Mode, all V-Chip (Parental Control) settings in the TV are reset to their default values; that is, the Lock System, if previously enabled from the Lock setup menu (see the Owner’s Manual for additional information), will now be disabled, and the individual Parental Control settings will be restored to default values.
206-4213 |
19 |
Installer Menu (Cont.)
Installer Menu Items 000 through 075
Menu |
Function |
Value Range |
Default Value |
Brief Description of Function and Comments |
|
Item |
|||||
000 |
INSTALLER SEQ |
0 ~ 3 |
0 |
Leave default set to 0. |
|
001 |
POWER MANAGE |
0 ~ 7 |
0 |
Sets number of hours of no activity before automatic shutoff. |
|
002 |
AC ON |
0 / 1 |
0 |
Set to 1 to enable Auto Turn ON when AC power is applied. |
|
003 |
BAND/AFC |
0 ~ 3 |
1 |
Selects Tuning Band: 0=Broadcast, 1=CATV, 2=HRC, 3=IRC |
|
004 |
STRT CHANNEL |
0 ~ 127, 255 |
255 |
Channel tuned when TV is turned ON. (Set to 255 to tune to channel |
|
tuned before TV turned OFF.) |
|||||
|
|
|
|
||
005 |
CHAN LOCK |
0 / 1 |
0 |
If set to 1, cannot tune from current channel. |
|
007 |
STRT VOLUME |
0 ~ 63, 255 |
255 |
Volume level when TV is turned ON. (Set to 255 to use volume level |
|
before TV turned OFF.) |
|||||
|
|
|
|
||
008 |
MIN VOLUME |
0 ~ 63 |
0 |
Sets minimum allowable volume setting. |
|
009 |
MAX VOLUME |
0 ~ 63 |
63 |
Sets maximum allowable volume setting. |
|
010 |
MUTE DISABLE |
0 / 1 |
0 |
Set to 1 to disable Mute Function. |
|
011 |
KEY DEFEAT |
0 / 1 |
0 |
Set to 1 to disable menu navigation keys on display panel. |
|
015 |
SLEEP TIMER |
0 / 1 |
1 |
Set to 1 to enable Sleep Timer. |
|
016 |
EN TIMER |
0 / 1 |
0 |
Set to 1 to enable On/Off Timers. |
|
017 |
ALARM |
0 / 1 |
1 |
Set to 1 to enable Alarm. |
|
020 |
FEATURE LEVEL |
0, 16 ~ 24 |
0 |
Determines an additional IR code scheme to which the TV will respond. |
|
021 |
V-CHIP |
0 / 1 |
1 |
Set to 1 to enable V-Chip (Parental Control) functions. |
|
022 |
MAX BLK HRS |
0 ~ 99 |
12 |
Sets number of V-Chip blocking hours. |
|
023 |
CAPTION LOCK |
0 / 1 |
0 |
Set to 1 to retain caption setting set before TV turned OFF. |
|
028 |
CH. OVERIDE |
0 / 1 |
1 |
If set to 0, limits direct access to favorite channels. |
|
029 |
OLD OCV |
0 / 1 |
0 |
Set to 1 to change MPI operation to OCV. |
|
030 |
ACK MASK |
0 / 1 |
0 |
If set to 1, enables ACK feature of MPI. |
|
031 |
POLL RATE |
20 ~ 169 |
94 |
Selects poll rate for MPI. |
|
032 |
TIMING PULSE |
186 ~ 227 |
207 |
Sets baud rate for MPI. |
|
035 |
HDMI1 ENABLE |
0 / 1 |
1 |
Set to 0 to disable HDMI 1. Set to 1 enable HDMI 1. |
|
039 |
REAR AUX EN. |
0 / 1 |
1 |
Set to 1 to enable display panel Video 1 input jack. |
|
041 |
SIMPLINK EN |
0 ~ 3 |
0 |
Determines the status of the SIMPLINK feature. (See detailed descriptions.) |
|
046 |
STRT AUX SRCE |
1, 3 ~ 5, 7, 255 |
7 |
Sets the starting Aux source (if item 004 STRT CHANNEL is set to 0). |
|
047 |
AUX STATUS |
0 / 1 |
0 |
Set to 1 for MPI Aux source to be reported as a channel number instead of |
|
Channel 0. |
|||||
|
|
|
|
||
053 |
DIS. CH-TIME |
0 / 1 |
0 |
Set to 1 to disable Channel-Time display. |
|
069 |
EN. CH-T COL. |
0 / 1 |
1 |
Set to 1 to enable custom color for the Channel-Time display. |
|
070 |
FOR. CH-TIME |
0 ~ 7 |
2 |
Chooses custom foreground color for the Channel-Time display. |
|
071 |
BCK. CH-TIME |
0 ~ 7 |
2 |
Chooses custom background color for the Channel-Time display. |
|
073 |
CH NOT AVBLE |
0 / 1 |
0 |
If set to 1 and item 028 CH. OVERIDE is set to 0, “NOT AVAILABLE” message |
|
is displayed if user direct tunes a channel that is not in the favorite channel list. |
|||||
|
|
|
|
||
075 |
REVERT CH |
0 / 1 |
0 |
If set to 1 and loss of MPI communication occurs, TV tunes to Start Channel. |
20 |
206-4213 |
Loading...