Loading...
Projection Television Users Guide
For Models:
HD-61Z585
HD-52Z585
HD-61Z575
HD-52Z575
Illustration of HD-52Z575 and RM-C15G
Important Note:
In the spaces below, enter the model and serial number of your television (located at the rear of the television cabinet). Staple your sales receipt or invoice to the inside cover of this guide. Keep this user’s guide in a convenient place for future reference. Keep the carton and original packaging for future use.
Model Number:
Serial Number:
LCT1611-001A-A 0504TNH-II-IM
Important Safety Precautions
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: To reduce the risk of electric shock. Do not remove cover (or back). No user serviceable parts inside. Refer servicing to qualified service personnel.
The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS TV SET TO RAIN OR MOISTURE.
CAUTION: TO INSURE PERSONAL SAFETY, OBSERVE THE FOLLOWING RULES REGARDING THE USE OF THIS UNIT.
1.Operate only from the power source specified on the unit.
2.Avoid damaging the AC plug and power cord.
3.Avoid Improper installation and never position the unit where good ventilation is unattainable.
4.Do not allow objects or liquid into the cabinet openings.
5.In the event of trouble, unplug the unit and call a service technician. Do not attempt to repair it yourself or remove the rear cover.
Changes or modifications not approved by JVC could void the warranty.
*When you don’t use this TV set for a long period of time, be sure to disconnect both the power plug from the AC outlet and antenna for your safety.
*To prevent electric shock do not use this polarized plug with an extension cord, receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure.
NOTICE (for USA)
This product has a High Intensity Discharge (HID) lamp that contains a small amount of mercury. It also contains lead in some components. Disposal of these materials may be regulated in your community due to environmental considerations. For disposal or recycling information, please contact your local authorities, or the Electronics Industries Alliance: http://www.eiae.org
2
•As an “ENERGY STAR®” partner, JVC has
determined that this product or product model meets the “ENERGY STAR®” guidelines for energy efficiency.
IMPORTANT SAFETY INSTRUCTIONS
1)Read these instructions.
2)Keep these instructions.
3)Heed all warnings.
4)Follow all instructions.
5)Do not use this apparatus near water.
6)Clean only with dry cloth.
7)Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
8)Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.
9)Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.
10)Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.
11)Only use attachments/accessories specified by the manufacturer.
12)Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
3
13)Unplug this apparatus during lightning storms or when unused for long periods of time.
14)Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15)Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus.
16)Avoid improper installation and never position the unit where good ventilation is impossible. When installing this TV, distance recommendations must be maintained between the set and the wall, as well as inside a tightly enclosed area or piece of furniture. Keep to the minimum distance guidelines shown for safe operation.
200 mm |
200 mm |
150 mm |
150 mm |
50 mm
17)Cautions for installation
—Do not tilt the TV towards the left or right, or towards the back.
—Install the TV in a corner on the floor so as to keep cords out of the way.
—The TV will generate a slight amount of heat during operation. Ensure that sufficient space is available around the TV to allow satisfactory cooling.
4
Warnings
Screen Burn-in
By displaying fi xed images for extended periods of time, can leave a subtle but permanent ghost image in your picture. This is referred to as "burn-in". To avoid this, mix your viewing pattern.
Examples include, but are not limited to the following:
•Stock-market report bars
•Shopping channel logos and pricing displays
•Video game patterns or scoreboards
•Bright station logos
•Internet web sites or other computer-style images.
•DVD discs, video tapes, laser discs
•Broadcast, cable, satellite channels or digital television tuners/converters.
For example...
TV on |
TV off |
XYZ |
XYZ |
Caring for the Cabinet
Normally, light dusting with a soft, non-scratching duster will keep your TV clean.
If you wish to wipe down the television, first unplug it. Then wipe gently with a soft cloth, slightly moistened with water. You can add a few drops of mild liquid detergent to the water to help remove spots of oily dirt.
•DO NOT allow liquid to enter the TV through the ventilation slots.
•DO NOT use strong or abrasive cleaners on the TV.
•DO NOT spray liquids or cleaners directly on the TV’s surface.
•DO NOT rub or scrub the TV harshly. Wipe the set gently with a soft cloth.
Caring for the Screen
The screen is treated with an electrostatic-proof coating. When it gets dirty, wipe it gently with a soft cloth. If the screen is very dirty, wipe it down with a cloth dipped in a diluted kitchen cleaner and thoroughly wrung-out. Then wipe immediately after with a clean, dry cloth.
Do not apply alcohol, organic solvents (like acetone), acidic or alkaline cleansers to the screen. These will remove the coating layer and cause discolorations.
Do not push or hit the screen. This could cause scratches on the screen surface and image distortions.
5
Warnings
Thank you for purchasing JVC’s model HD-61Z585 , HD-52Z585, HD-61Z575 or HD-52Z575 HDTV-ready projection television which uses the high-quality HD-ILA projection system. This is one of the highest quality and most technologically advanced televisions available today. It is recommended that you read this instruction manual before using your television in order to learn about it’s many features. Cautions related to the safe use of the device and important information which will help you to be able to use this device for a long time is in the Appendix. Once again, thank you for purchasing this television and please enjoy using it.
In order to use the television for a long time
This television uses a lamp to project the picture onto the screen. Before using this television, please read the safety cautions and information about this television which are summarized below.
1. When the power is turned on, the warming up commences
This television uses a lamp to project the picture onto the screen. Once the lamp has warmed up, you can enjoy the pictures at their full brightness. What happens when the power is turned on is explained below. Immediately after the power is turned on, since the lamp has not had time to warm up, the picture is displayed only dimly on the screen. As the lamp warms up, the picture becomes brighter. It takes approximately one minute for the lamp to warm up to it’s normal operating temperature. There are 2 LED indicators on the front panel of the television that can be used as a guide. When the POWER button is pressed, the Lamp LED indicator blinks in orange for approximately 1 minute at approximately every 2 seconds, and then goes out.
Note: It is impossible to turn the power off during this period. After 1 or more minutes have passed, you can turn off the power.
2. Cooling the inside of the television and the lamp
Cooling is also performed while the television is being shut down.
When the POWER button is pressed to turn off the power, the following operations are performed. When the television is turned off, the picture on the screen disappears. Once the screen is dark, cooling is performed for approximately 90 seconds. When the cooling is being performed, the Lamp LED indicator on the front panel blinks in orange at approximately every 3 seconds. The television can not be operated while the cooling is being performed.
After the cooling has been performed for 90 seconds, the power is turned off. Do not remove the electrical plug until after the cooling process has completed. If the electrical plug is removed before the cooling process has completed, the internal circuits and lamp may overheat leading to the life of the lamp being shortened and the possibility of malfunctions.
Do not block the ventilation holes.
Do not block the ventilation holes while the power is turned on. Do not block the air intake holes behind the speaker grills.
3. The lamp is a consumable item
Replace the lamp when it has blown or when the picture becomes dark. The lamp is a user replaceable item. The lamp must be recycled. For a detailed explanation on how to recycle the lamp, refer to the Appendix and the instructions that are included with the replacement lamp kit. The life of the lamp changes depending on the atmospheric temperature and altitude in which the TV is being used.
6
Warnings
4. The television requires a lot of electrical power
It is recommended that the television is connected directly to the wall socket, and not to another device. When connecting the television to a wall socket that is being used by another device, or when using an extension cord, be careful not to exceed the electrical capacity of the socket.
Do not turn the power on and off repeatedly in a short amount of time.
It subjects the television and the lamp to stress and may lead to malfunctions and the life of the lamp being shortened.
5. The screen is made of plastic
Handle the screen very carefully as it can scratch easily. Do not rub, hit or press on it with any hard objects. When the screen is dirty, gently wipe it with a soft cloth. Refer to the Appendix for details on how to clean the screen.
6. Caution! Warm air from the air ducts
This unit has an air duct for cooling. The duct will blow warm air while the television is operating. When placing the television, make sure not to locate it too close to wallpaper. The warm air could cause the color of the wallpaper to change. Also, take care to keep children and pets away from the warm air ducts. Long exposure to the warm air from the ducts could cause a minor burn.
7. Caution! Moving this television
When lifting this television, Do not hold by the screen frame. Holding the screen frame could cause it to detach, causing the television to fall.
8. Do not replace the lamp immediately after use
The lamp becomes extremely hot during use. If the lamp is touched immediately after use before it has a chance to cool down, there is a danger of burns. Be careful when handling the lamp.
9. Do not touch the lamp glass
If the lamp is used when there is dirt from fi ngers on the lamp glass, there is a possibility of the lamp breaking. Be careful not to touch the lamp glass.
10. ILA element characteristics
Do not project still pictures or pictures that have still segments for a long period of time. The still parts of the picture may remain on the screen. This is a characteristic of ILA elements and not a malfunction. The picture will disappear over time.
11. Condensation
When a heater is turned on or the television is moved from a cold place to a hot place, droplets of water may form on the lamp and screen. This is called condensation. If the television is used while this condensation is still present, the picture may seem distorted, and the inside of the screen may become dirty. In this case, wait until the condensation has gone before using the television.
12. Do not open the rear cabinet of this television
This television has a DIGITAL-IN terminal. Opening up the rear cabinet will violate the copyright of the program or software shown on the television. Please do not open the rear cabinet.
13. Usable Time
Do not keep the TV on for more than 24 hours consecutively. There is a possibility of the life of the TV being shortened.
7
Important Safety Precautions . 2
Warnings . . . . . . . . . . . . 5
Quick Setup . . . . . . . . . . . 9
Unpacking your TV . . . . . . . . . . . . 9 TV Models . . . . . . . . . . . . . . . . 10 TV Remote Control . . . . . . . . . . . 11 Getting Started . . . . . . . . . . . . . 12 The Remote Control . . . . . . . . . . 12 Connecting Your Devices . . . . . . . 13 Interactive Plug In Menu . . . . . . . . 22
Remote Programming . . . . . 25
Setting CATV, VCR and DVD Codes . . . 25
CATV or Satellite Codes . . . . . . . . 25
VCR Codes . . . . . . . . . . . . . . 26
DVD Codes . . . . . . . . . . . . . . 27
Search Codes . . . . . . . . . . . . . 28
Onscreen Menus . . . . . . . . 29
Using the Guide . . . . . . . . . . . . . 29
Onscreen Menu System . . . . . . . . . 30
Initial Setup . . . . . . . . . . 32
Auto Tuner Setup . . . . . . . . . . . . 32
Channel Summary . . . . . . . . . . . . 32
V-Chip . . . . . . . . . . . . . . . . . . 34
Set Lock Code . . . . . . . . . . . . . 40
Auto Demo . . . . . . . . . . . . . . . 41
Language . . . . . . . . . . . . . . . . 41
Closed Caption . . . . . . . . . . . . . 42
Auto Shut Off . . . . . . . . . . . . . . 42
XDS ID . . . . . . . . . . . . . . . . . 43
Noise Muting . . . . . . . . . . . . . . 43
Front Panel Lock . . . . . . . . . . . . 43
V1 Smart Input . . . . . . . . . . . 44
Video Input Label . . . . . . . . . . 44
Position Adjustment . . . . . . . . . . . 45
Power Indicator . . . . . . . . . . . . . 45
TV Speaker . . . . . . . . . . . . . . 46
Audio Out . . . . . . . . . . . . . . 46
Digital-In . . . . . . . . . . . . . . . . . 47
Digital-In Audio . . . . . . . . . . . . . 47
Center CH Input . . . . . . . . . . . . . 47
Picture Adjust . . . . . . . . . 48
Picture Settings . . . . . . . . . . . . . 48 Adjust Picture Settings . . . . . . . . . 48 Color Temperature . . . . . . . . . . . . 48 Digital Noise Clear . . . . . . . . . . . . 49 Natural Cinema . . . . . . . . . . . 49 Color Management . . . . . . . . . . . 49 Dynamic Gamma . . . . . . . . . . . 50 Reset . . . . . . . . . . . . . . . . . . 50
Table of Contents
Sound Adjust . . . . . . . . . 51
Sound Settings . . . . . . . . . . . . . 51 Adjust Sound Settings . . . . . . . . . 51 MTS (Multi-channel Sound) . . . . . . . 51 Reset . . . . . . . . . . . . . . . . 51
Clock Timers . . . . . . . . . . 52
Set Clock . . . . . . . . . . . . . . |
. . 52 |
On/Off Timer . . . . . . . . . . . . . |
. . 53 |
Lamp Reset . . . . . . . . . . . . . . 54 |
|
Button Functions . . . . . . . 55 |
|
Multi Screen Function . . . . . . . . |
. . 55 |
Index . . . . . . . . . . . . . . . . |
. . 55 |
Twin . . . . . . . . . . . . . . . . . 55 |
|
Freeze . . . . . . . . . . . . . . . . |
. . 56 |
Swap . . . . . . . . . . . . . . . |
. . 56 |
Select . . . . . . . . . . . . . . . . |
. . 56 |
Power . . . . . . . . . . . . . . . . |
. . 57 |
Number Buttons . . . . . . . . . . . |
. . 57 |
Tune . . . . . . . . . . . . . . . 57 |
|
Input . . . . . . . . . . . . . . . . . |
. . 57 |
Digital-In . . . . . . . . . . . . . . . 57 |
|
Return+/TV . . . . . . . . . . . . . |
. . 58 |
Sound . . . . . . . . . . . . . . . . |
. . 58 |
Muting . . . . . . . . . . . . . . . . |
. . 58 |
Video Status . . . . . . . . . . . . . |
. . 59 |
TheaterPro D6500K . . . . . . . . . |
. . 59 |
Sleep Timer . . . . . . . . . . . . . |
. . 59 |
Display . . . . . . . . . . . . . . . |
. . 60 |
C.C. . . . . . . . . . . . . . . . . . |
. . 60 |
Aspect . . . . . . . . . . . . . . . |
. . 61 |
Aspect Ratios . . . . . . . . . . . |
. . 61 |
Menu . . . . . . . . . . . . . . . . |
. . 62 |
OK . . . . . . . . . . . . . . . . . |
. . 62 |
Back . . . . . . . . . . . . . . . . . |
. . 62 |
Channel +/- . . . . . . . . . . . . . 62 |
|
Volume +/- . . . . . . . . . . . . . 62 |
|
TV/CATV Slide Switch . . . . . . . . |
. . 63 |
VCR/DVD Slide Switch . . . . . . . |
. . 63 |
VCR Buttons . . . . . . . . . . . . . |
. . 63 |
DVD Buttons . . . . . . . . . . . . . |
. . 63 |
Light . . . . . . . . . . . . . . . . . |
. . 63 |
Appendices . . . . . . . . . . 64
No Program . . . . . . . . . . . . . . 64 Troubleshooting . . . . . . . . . . . . . 65 Changing The Lamp . . . . . . . . . . 67 Replacement Lamp Kit . . . . . . . . 68 Lamp Messages . . . . . . . . . . . . 68 How To Replace The Lamp . . . . . . . 69 Warning LED Messages . . . . . . . . 72 Specifications . . . . . . . . . . . . . . 73 Warranty . . . . . . . . . . . . . . 74 Notes . . . . . . . . . . . . . . . . . 76
8
Quick Setup |
Unpacking your TV |
|
|
Thank you for your purchase of a JVC Color Television. Before you begin setting up your new television, please check to make sure you have all of the following items. In addition to this guide, your television box should include:
1 Television |
1 Remote Control |
||||
|
TV CATV |
VCR |
DVD |
ASPECT |
POWER |
|
|
|
|
|
|
|
|
MULTI SCREEN |
|
||
|
TWIN |
|
|
INDEX |
|
|
FREEZE |
SWAP |
SELECT |
|
|
|
INPUT 1 |
1 |
|
2 |
3 |
|
V1 |
|
|||
|
INPUT 2 |
4 |
|
5 |
6 |
|
V2 |
|
|||
|
INPUT 3 |
|
|
|
|
|
V3 |
7 |
|
8 |
9 |
|
INPUT 4 |
|
|
0 |
|
|
V4 |
|
|
|
|
|
DIGITAL-IN |
THEATER |
|
VIDEO |
|
|
PRO |
|
STATUS |
||
|
D-IN |
|
|
|
|
|
SLEEP TIMER DISPLAY |
SOUND |
LIGHT |
||
|
MUTING |
|
|
|
C.C. |
|
|
|
CH |
|
|
|
VOL |
OK VOL |
|||
|
|
|
CH |
|
|
|
MENU |
|
|
|
BACK |
|
VCR CHANNEL |
|
VCR / DVD |
|
|
|
PREV |
NEXT |
|
POWER |
TV / VCR |
|
REW |
|
PLAY |
FF |
|
|
REC |
STOP |
PAUSE |
||
|
OPEN CLOSE |
|
STILL PAUSE |
||
|
|
RM-C15G |
|
||
Two AA
Batteries
Alkaline AA |
Alkaline AA |
Note: Your television and/or remote control may differ from the examples illustrated here.
Once you have unpacked your television, the next step is to connect it to your antenna/ cable or satellite system and to connect the audio/video devices you want to use with your television. To make these connections you will use plugs like the ones illustrated below.
Coaxial Cables
Used to connect an external antenna or cable TV system to your TV.
S-Video Cable
Used to make video connections with S-Video VCRs, Camcorders and DVD players.
Component Cables
Composite Cables
Audio Cables
Used to connect audio/ video devices like VCRs, DVD players, stereo amplifiers, game consoles, etc.
AV CompuLink Cable
Used to connect JVC
AV CompuLink capable components for an automated home theater.
We recommend that before you start using your new television, you read your entire User’s Guide so you can learn about your new television’s many great features. If you’re anxious to start using your television right away, a quick setup guide follows on the next few pages.
9
Quick Setup |
TV Models |
|
|
NOTE: Before you connect your television to another device, please refer to the proper diagrams for your specific TV and remote. These will help assist you in understanding how to connect your television to another device, as well as use the remote to set up your television.
Rear Panel Diagram
MODELS:
HD-61Z585
HD-52Z585
HD-61Z575
HD-52Z575
CENTER CHANNEL |
INPUT-2 |
|
||
|
|
|||
INPUT |
|
|
||
|
|
Y |
VIDEO |
|
AV COMPULINK III |
L |
Pb |
L |
|
|
|
|
||
AUDIO |
|
AUDIO |
||
|
R |
Pr |
R |
|
|
S-VIDEO |
S-VIDEO |
|
|
VIDEO |
|
|
|
|
(DIGITAL) |
|
|
|
|
AUDIO |
OVER |
OVER |
|
|
(DIGITAL) |
|
|
Y |
|
|
|
|
||
|
VIDEO |
VIDEO |
|
|
|
L |
L |
Pb |
|
DIGITAL IN |
I |
I |
|
|
AUDIO |
AUDIO |
|
||
|
I |
|
||
|
I |
|
||
|
R |
Pr |
||
|
R |
|||
|
|
|||
|
INPUT-3 |
INPUT-1 |
|
|
UNPLUG THE POWER CORD FROMAC OUTLET |
|
|
||
BEFORE REMOVING THE REAR COVER |
|
|
|
|
When the rear cover is removed, follow "CAUTIONATDISASSEMBLY" |
|
|
||
procedure in the service manual before plugging theTV's power |
|
|
|
|
cord into anAC outlet. Failure to follow the procedure will result |
|
|
|
|
in PERMANENTdamage to some of the television features. |
|
|
|
|
DÉBRANCHEZ LE CORDON DE LAPRISE DE COURANT |
|
|
|
|
C.A.AVANTDE RETIRER LE COUVERCLEARRIÈRE. |
|
SUBWOOFER |
||
Une fois le couvercle arrière déposé suivez l procédure |
|
OUT |
|
|
«ATTENTION LORS DU DÉMONTAGE » décrite dans une |
|
|
||
prise c.a. L'omission de suivre la procédure causera des |
|
|
|
|
dommages PERMANENTS à certaines fonctions du téléviseur. |
|
|
75Ω |
|
|
|
L |
||
Licensed from BBE Sound, Inc. under USP4638258, 4482866 |
(VHF/UHF) |
|||
|
||||
and 5510752. |
|
AUDIO OUTPUT |
||
BBE is a registered trademark of BBE Sound, Inc. |
|
|||
Sous licence de BBE Sound, Inc. |
|
R |
|
|
BBE est une marque de fabrique déposée de BBE Sound, Inc. |
|
|||
Autorizado con licencia de BBE Sound, Inc.
BBE es une marca comercial registrada de BBE Sound, Inc.
Front Panel Diagram |
Side Panel Diagram |
LAMP |
|
POWER |
MENU INPUT 4 |
|
S-VIDEO |
|
OPERATE |
LAMP |
|
+ |
|
OVER |
|
CHANNEL |
|
– |
LAMP LED |
VIDEO |
|
POWER |
+ |
POWER LED |
L/MONO |
|
VOLUME |
|
– |
|
R |
|
AUDIO |
• For information on the LED, see page 72.
MODELS: HD-61Z585, HD-52Z585, HD-61Z575, HD-52Z575
10
Quick Setup |
TV Remote Control |
|
|
TV CATV |
VCR |
DVD |
|
POWER |
|
|
|
|
ASPECT |
|
|
|
MULTI SCREEN |
|
|||
TWIN |
|
|
INDEX |
|
|
FREEZE |
SWAP |
SELECT |
|
||
INPUT 1 |
1 |
|
|
2 |
3 |
V1 |
|
|
|||
INPUT 2 |
4 |
|
|
5 |
6 |
V2 |
|
|
|||
INPUT 3 |
7 |
|
|
8 |
9 |
V3 |
|
|
|||
INPUT 4 |
|
|
|
0 |
RETURN+ |
V4 |
TUNE |
|
TV |
||
DIGITAL-IN |
THEATER |
|
|
VIDEO |
|
PRO |
|
|
STATUS |
||
D-IN |
|
|
|
|
|
SLEEP TIMER DISPLAY |
SOUND |
LIGHT |
|||
|
+ |
|
|
|
|
MUTING |
|
|
|
|
C.C. |
|
|
CH |
|
C.C. |
|
|
|
|
|
||
VOL |
OK |
VOL |
|||
|
|
|
|
||
|
|
CH |
|
|
|
MENU |
|
|
|
|
BACK |
VCR CHANNEL |
|
VCR / DVD |
|||
PREV |
NEXT |
|
POWER |
TV / VCR |
|
REW |
|
PLAY |
|
FF |
|
REC |
STOP |
|
PAUSE |
||
OPEN CLOSE |
|
|
STILL PAUSE |
||
|
RM-C15G |
|
|
||
RM-C15G
MODELS:
HD-61Z585
HD-52Z585
HD-61Z575
HD-52Z575
• For information on remote control buttons, see pages 55 - 63.
11
Quick Setup |
Getting Started |
|
|
Getting Started
These quick setup pages will provide you, in three easy steps, with the basic information you need to begin using your new television right away.
If you have questions, or for more detailed information on any of these steps, please consult other sections of this manual.
Step 1 – The Remote Control
Before you can operate your remote control, you first need to install the batteries (included).
Slide the cover on the back of the remote down towards the bottom of the remote control. Insert two batteries (included) carefully noting the “+” and “–” markings, placing the “–” end in the
unit first. Slide the cover back into place.
When you change the batteries, try to complete the task within three minutes. If you take longer than three minutes, the remote control codes for your VCR, DVD, and/or cable box/satellite receiver may have to be reset. See pages 25 - 28.
Key Feature Buttons
The four key feature buttons at the center of the remote can be used for basic operation of the television. The top and bottom buttons will scan forward and back through the available channels. To move rapidly through the channels using
JVC’s Hyperscan feature, press and hold CH+ or CH–. The channels will zip by at a rate of five channels per second. The right and left buttons will turn the volume up or down. These buttons are also marked with four arrows and are used with JVC’s onscreen menu system. To use the onscreen menus, press the MENU button.
MUTING |
C.C. |
CH C.C.
VOL OK VOL
CH
MENU |
BACK |
12
|
|
|
Quick Setup |
Connections |
|
|
|
|
Basic Operation
Turn the television on and off by pressing the POWER button at the top right corner of the remote. The POWER LED will light blue. If this is the first time you are turning on the TV, the interactive plug-in menu appears.
•Make sure the TV/CATV switch is set to TV. Move the switch to CATV only if you need to operate a cable box.
•Slide the VCR/DVD selector switch to VCR to control a VCR. Slide to DVD to control a DVD player. Please see pages 25 to 28 for instructions on
programming your remote control to operate a cable box, VCR or DVD player.
POWER
TV CATV
VCR DVD
Note:
• If the lamp replacement message appears when you turn the television ON, see page 68.
Step 2 – Connecting Your Devices
Please follow the flow chart below to determine which connection setup is right for you. Then, refer to the appropriate diagrams to connect your television to other devices that you may have. After you are finished connecting your devices, plug the power cord into the nearest power outlet and turn on the TV.
A VCR is not necessary for operation of the television. If you follow these diagrams and the television does not work properly, contact your local cable operator.
•To connect a DVD player, see Diagram #3. A DVD player is optional.
•If you have a satellite television system, please refer to the satellite TV manual.
Do you use a Cable TV Box?
Yes |
No |
Do you have a VCR? |
Do you have a VCR? |
|
|
Yes |
No |
Yes |
No |
Diagram #2 Diagram #1 |
Diagram #3 Diagram #1 |
13
Quick Setup |
Connections |
|
|
Diagram #1
Note:
Cable or Antenna
Output
|
Coaxial Cable |
75Ω |
OR |
(VHF/UHF) |
OUT IN
TV Rear Panel
Cable Box
•If you do not have a cable box, connect the cable wire from the wall outlet into the back of the TV.
Diagram #2
S-VIDEO |
S-VIDEO |
|
OVER |
OVER |
|
|
|
Y |
VIDEO |
VIDEO |
|
L |
L |
Pb |
I
I
AUDIO |
AUDIO |
|
|
I |
|
||
I |
|
||
R |
Pr |
||
R |
|||
|
INPUT-3 INPUT-1
TV Rear Panel
75Ω
(VHF/UHF)
OR
VCR
IN
IN
OUT
R L V
OUT
OUT IN
Cable Box
Notes:
Cable or Antenna
Output
Coaxial Cable
OUT OUT |
IN |
Two-Way
Splitter
•If your VCR is a mono sound unit, it will have only one audio out jack. Connect it to the LEFT AUDIO INPUT on the front of the TV.
•Use the S-Video connection if possible for superior picture quality.
•Your VCR must be turned on to view premium cable channels.
14
Quick Setup |
Connections |
|
|
Notes:
•Green, blue and red are the most common colors for DVD cables. Some models may vary colors. Please consult the user’s manual for your DVD player for more information.
•Be careful not to confuse the red DVD cable with the red audio cable. It is best to complete one set of connections (DVD or audio output) before starting the other to avoid accidentally switching the cables.
•You may also connect the DVD player to Input 1.
Diagram #3
|
Coaxial Cable |
Cable or Antenna |
|
||
|
|
|
|
|
|
|
|
|
|
Output |
|
|
Two-Way Splitter |
|
|
||
|
IN |
|
|
|
|
OUT OUT |
|
|
|
|
|
|
|
|
|
TV Rear Panel |
|
|
|
|
75Ω |
|
|
|
|
|
(VHF/UHF) |
|
|
|
|
|
|
INPUT-2 |
|
|
|
|
|
Y |
VIDEO |
|
R |
L |
V |
Pb |
L |
|
|
AUDIO |
|||
|
IN |
|
|
|
|
IN |
|
|
Pr |
R |
|
|
|
|
|||
|
|
|
|
||
OUT |
OUT |
|
|
S-VIDEO |
|
|
|
|
|
||
|
|
|
|
|
|
VCR |
|
|
OR |
OVER |
|
|
|
|
|
||
|
|
|
|
|
|
|
|
|
|
|
Y |
|
|
|
|
VIDEO |
|
|
|
|
|
L |
Pb |
|
|
|
|
I |
|
|
|
|
|
AUDIO |
|
|
|
|
|
I |
Pr |
|
|
|
|
R |
|
|
|
|
|
INPUT-1 |
|
|
Y |
|
Green |
|
PB |
|
Blue |
AUDIO OUT |
PR |
|
Red |
R L |
OUT |
DVD Player (OPTIONAL) |
|
15
Quick Setup |
Connections |
|
|
Connecting to JVC AV Compu Link
JVC’s AV CompuLink feature makes playing video tapes or DVDs totally automatic. Simply insert a pre-recorded tape into your JVC brand VCR or DVD into your JVC DVD player and the device will automatically turn on and begin playback. At the same time, using the
AV CompuLink, the VCR or DVD player sends a signal to the television telling it to turn on and switch to the proper video input.
•The AV CompuLink cable may be included with the JVC AV CompuLink unit you wish to connect. If it is not, contact JVC Parts Department at (800)-882-2345, or www.jvcservice.com for part # EWP 805-012.
•AV CompuLink can only be used with JVC brand products.
AV CompuLink Cable
To Connect: Plug one end of the AV CompuLink cable into the AV COMPULINK INPUT on your VCR, DVD, or other CompuLink device. Plug the other end of the AV CompuLink cable into the AV COMPULINK at the rear of the television.
Note:
•The AV CompuLink cable has a male 3.5 mm (mono) plug on each end.
VCR
AV COMPULINK III
IN
V L R
IN
OUT
OUT
AV CompuLink
TV Rear Panel
Notes:
•In order for the VCR playback to begin automatically, the recording tabs must be removed from the VHS tape. If the tab is in place, automatic switching will occur when you push the VCR’s PLAY button.
•If your JVC brand VCR has “A code/B code remote control switching” (see your VCR’s instruction book), using VCR A code will switch the TV to input 1.
•Refer to your DVD instruction book for detailed connection information.
•To connect a JVC HiFi receiver or amplifier for a completely automated home theater, see the receiver connection instructions for detailed connection information.
•AV CompuLink is compatible with select AV CompuLink receivers.
16
Quick Setup |
Connections |
|
|
Connecting to a Camcorder
You may connect a camcorder, game console or other equipment to your television by using the side input jacks (Input 4) located on the side of the television. You can also connect these using the television’s rear input jacks, using the same instructions.
MENU |
INPUT 4 |
|
S-VIDEO |
OPERATE
+
OVER
CHANNEL |
- OR - |
CAMCORDER |
–
VIDEO
+
L/MONO
VOLUME
–
R
AUDIO
1)Connect a yellow composite cable from the camcorder VIDEO OUT, into the VIDEO IN on the side of the TV, OR connect an S-Video cable from the side of the TV to the camcorder.
2)Connect a white cable from the camcorder LEFT AUDIO OUT, into the LEFT AUDIO IN on the side of the TV.
3)Connect a red cable from the camcorder RIGHT AUDIO OUT, into the RIGHT AUDIO IN on the side of the TV.
Note:
•If your camcorder is a mono sound model it will have only one AUDIO OUT. Connect it to the L/MONO on the side of the TV.
17
Quick Setup |
Connections |
|
|
Connecting to the Surround Amplifier
In multi-channel sound such as 5.1 channel, the speech characters are played back from the center speaker.
A center speaker in a movie theater is set in back of the screen so it can recreate a conversation scene in the movie more naturally. By using your TV's speaker as the center speaker, you can obtain the same sound effect as in a movie theater in you home theater sound system.
Front |
Front |
Surround |
TV Rear Panel
CENTERCHANNEL
INPUT
L
AUDIO
R 
CENTER CHANNEL OUTPUT
(VARIABLE OUTPUT)
1)Connect the Pin cable from the TV's CENTER CHANNEL INPUT terminal to the surround amplifier's CENTER CHANNEL OUTPUT terminal.
Note:
• Please read the benefit of this feature on page 47.
Connecting to an External Amplifier
Subwoofer Out - Use a powered subwoofer with the surround feature to simulate a home theater system. Simply connect the subwoofer to the back of the TV.
TV Rear Panel
SUBWOOFER |
Speaker |
Speaker |
Powered |
OUT |
|||
L |
|
Amplifier |
Subwoofer |
|
|
||
AUDIO OUTPUT |
|
|
|
R |
|
|
|
1)Connect a white cable from the LEFT AUDIO OUTPUT on the back of the TV to the LEFT AUDIO INPUT on the amplifier.
2)Connect a red cable from the RIGHT AUDIO OUTPUT on the back of the TV to the RIGHT AUDIO INPUT on the amplifier.
3)Connect a black cable from the SUBWOOFER OUT on the back of the TV to the LINE INPUT of the subwoofer.
Notes:
•Refer to your amplifier’s manual for more information.
•You can use AUDIO OUTPUT for your home theater system.
18
Quick Setup |
Connections |
|
|
Connecting to a Digital TV Receiver
By connecting a Digital TV Receiver, high definition pictures can be displayed on your TV in their digital form.
TV Rear Panel
DTV Decoder
DIGITAL OUT |
AUDIO OUT |
R L
HDMI to DVI Cable
|
CENTER CHANNEL |
|
INPUT |
AV COMPULINK III |
L |
|
|
|
AUDIO |
|
R |
VIDEO |
|
(DIGITAL) |
|
AUDIO |
|
(DIGITAL) |
|
DIGITAL IN |
|
After the connections have been made, tighten the screw to secure the cables.
1)Connect the HDMI to DVI Cable from the DIGITAL OUT on the back of your DTV decoder, to the DIGITAL-IN on the back of your television.
2)Connect a red cable from the DTV decoder RIGHT AUDIO OUT, to the RIGHT AUDIO DIGI- TAL-IN on the back of your television.
3)Connect a white cable from the DTV decoder LEFT AUDIO OUT, to the LEFT AUDIO DIGI- TAL-IN on the back of your television.
•The digital-in terminal is not compatible with the picture signal of a personal computer.
•Use a HDMI to DVI cable (commercially available) in order to digitally connect the television with a DTV decoder.
Notes:
•If 480p signals (640x480 or 720x480) are displayed on the screen, the horizontal balance may be slightly shifted. Access the “DIGITAL-IN” in the initial setup menu to adjust it. (Refer to page 47.)
•When you do the above connection, set DIGITAL-IN AUDIO in the Initial Setup menu to ANALOG. See "DIGITAL-IN AUDIO", page 47.
19
Quick Setup |
Connections |
|
|
Connecting to a HDMI Compatible Device
By connecting a HDMI compatible device, high definition pictures can be displayed on your TV in their digital form. Some HDMI devices can include DVD players, D-VHS or any HDMI compatible device.
HDMI (High Definition Multimedia Interface) is the first industry supported, uncompressed, all digital audio/video interface. HDMI provides and interface between any audio/video source, such as a set-top box, DVD player, A/V receiver or an audio and/or video monitor, such as a digital television (DTV).
HDMI Compatible Device
|
|
|
CENTER CHANNEL |
|
|
|
INPUT |
DIGITAL OUT |
AUDIO OUT |
|
|
|
L |
R |
L |
|
|
AV COMPULINK III |
|
|
|
|
AUDIO |
|
|
|
R |
|
|
VIDEO |
|
|
|
(DIGITAL) |
|
|
|
AUDIO |
|
|
|
(DIGITAL) |
|
HDMI Cable
DIGITAL IN
TV Rear Panel
1)Connect the HDMI Cable from the DIGITAL OUT on the back of your DTV or HDMI device, to the DIGITAL-IN on the back of your television.
Note:
•When you do the above connection, set DIGITAL-IN AUDIO in the Initial Setup menu to DIGITAL. See "DIGITAL-IN AUDIO", page 47.
20
Quick Setup |
Connections |
|
|
Connecting to an AV Receiver using your television's V1 Smart Input
By connecting your AV Receiver to your television's V1 Smart Input, you can watch picture sources from many different devices, without having to change or use the other input connections on your TV. This allows you to free up the other input connections so you can connect more devices to your television.
AV Receiver
MONITOR |
Y |
|
OUT |
||
|
||
|
PB |
|
|
PR |
|
|
MONITOR OUT |
S-VIDEO |
|
OVER |
|
|
Y |
VIDEO |
|
L |
Pb |
I |
|
AUDIO |
|
I |
Pr |
R |
|
INPUT-1 |
|
TV Rear Panel
1)Connect an S-Video Cable from the AV Receiver's MONITOR OUT, to the S-Video INPUT-1 on the back of your television.
2)Connect a Yellow Composite Cable from the AV Receiver's MONITOR OUT, into the VIDEO INPUT-1 on the back of your television.
3)Connect a Green Component Cable from the AV Receiver's Y MONITOR OUT, into the Y VIDEO INPUT-1 on the back of your television.
4)Connect a Blue Component Cable from the AV Receiver's PB MONITOR OUT, into the Pb VIDEO INPUT-1 on the back of your television.
5)Connect a Red Component Cable from the AV Receiver's PR MONITOR OUT, into the Pr VIDEO INPUT-1 on the back of your television.
Note:
•Please refer to your AV Receiver instruction manual for more information on connecting your speakers and other devices like a DVD player.
•Use your AV Receiver's remote to switch to the different devices you have connected.
•Some AV Receivers may not respond when the V1 Smart Input function is turned on.
•If you have video connections for each input device connected to your AV Receiver, you should not connect them using both S-Video and Composite connection at the same time when you are using V1 Input as the V1 Smart Input. In this case we recommend using the S-Video connection.
21
Quick Setup |
Plug-In Menu |
|
|
Step 3 – The Interactive Plug In Menu
When you turn your television on for the first time the interactive plug-in menu will appear. The plug-in menu helps you to get your TV ready to use by letting you set your preferences for:
•The language in which you want the onscreen menus to appear.
•Setting the TV’s clock to the correct time so your timer functions will work properly. You can choose “AUTO” or “MANUAL” for setting the clock.
•The auto tuner setup of which channels you wish to receive.
We recommend you complete the interactive plug-in items before you start using your television.
Notes:
•The interactive plug-in menu setting does not appear if your TV has been turned on before. In this case use the onscreen menus to perform these settings. See pages 41, 52, 32.
•If you press the Menu button while setting up the interactive plug-in menu, it will skip over it.
Language
After the “JVC INTERACTIVE PLUG IN MENU” has been displayed, the TV automatically switches to the LANGUAGE settings. You can choose to view your onscreen menus in three languages: English, French (Français) or Spanish (Español).
LANGUAGE/LANGUE/IDIOMA |
|
|
|
|
|
|
|
|
ENGLISH |
|
|
|
NEXT |
|
|
|
|
|
|
|
SELECT OPERATE |
MENU EXIT |
|
®To choose a language: (English, Français or Español)
†To NEXT (To set clock)
(To be continued...)
22
Quick Setup |
Plug-In Menu |
|
|
Auto Clock Set
Before you use any of your TV’s timer functions, you must first set the clock. You may precisely set your clock using the XDS time signal broadcast by most public broadcasting stations. If you do not have this in your area, you will have to set the clock manually. See manual clock set below. To set the clock using the XDS signal:
SET CLOCK
|
MODE |
AUTO |
|
|
TIME |
-- : -- -- |
|
|
TIME ZONE |
ATLANTIC |
|
|
D.S.T. |
ON |
|
|
|
NEXT |
|
|
|
|
|
|
SELECT OPERATE |
MENU EXIT |
|
®To choose AUTO
†To TIME ZONE
®To select your time zone: (Atlantic, Eastern, Central, Mountain, Pacific, Alaska or Hawaii)
†To move to D.S.T. (Daylight Savings Time)
®To turn D.S.T. ON or OFF
†To NEXT (To Auto Tuner Setup)
Notes:
•D.S.T. can be used only for US and Canada when it is set to ON in the SET CLOCK menu.
•Only when the MODE set to AUTO, the Daylight Savings Time feature automatically adjusts your TV’s clock for Daylight Savings. The clock will move forward one hour at 2:00 am on the first Sunday in April. The clock will move back one hour at 2:00 am on the last Sunday in October.
•You will have to reset the clock after a power interruption. You must set the clock before operating any timer functions.
Manual Clock Set
To set your clock manually (without using the XDS signal), choose MANUAL. If you choose AUTO, see auto clock set above.
SET CLOCK
|
MODE |
|
MANUAL |
|
|
TIME |
|
-- : -- -- |
|
|
TIME ZONE |
|
ATLANTIC |
|
|
D.S.T. |
|
ON |
|
|
|
START CLOCK |
|
|
|
|
|
|
|
|
SELECT |
OPERATE |
MENU EXIT |
|
®To choose MANUAL
†To TIME
®To set the hour
†To minute
®To set the minute
†To Start Clock
Note:
•You will have to reset the clock after a power interruption. You must set the clock before operating any timer functions.
(To be continued...)
23
Quick Setup |
Plug-In Menu |
|
|
Auto Tuner Setup
In auto tuner setup, the TV automatically scans through all available channels, memorizing the active ones and skipping over blank ones or channels with weak signals. This means when you scan (using the CHANNEL +/– buttons) you will receive only clear, active channels.
AUTO TUNER SETUP
|
TUNER MODE |
CABLE |
|
|
START |
|
|
|
|
|
|
|
SELECT OPERATE |
MENU EXIT |
|
®To choose CABLE or AIR (or SKIP when you skip Auto Tuner Setup)
†To START
Press the OK button
NOW
PROGRAMMING !
48
Programming will take approximately 1 to 2 minutes.
When the setup is finished, THANK YOU!! SETUP IS NOW COMPLETE is displayed. Your quick setup is now complete. You can now begin watching your television, or you can continue on in this guide for more information on programming your remote control, or using the
JVC onscreen menu system to customize your television viewing experience.
Notes:
•Noise muting will not work during Auto Tuner Setup.
•Skip appears only for interactive plug-in menu.
Cable Box and Satellite Users: After your auto tuner setup is complete, you may, (depending on the type of hookup), have only 1 channel, usually 3 or 4 in the auto tuner memory. This is normal.
STOP The Quick Setup is complete
24
Remote Programming
Setting the CATV, VCR and DVD Codes
You can program your remote to operate your cable box, satellite receiver, VCR or DVD player by using the instructions and codes listed below. If the equipment does not respond to any of the codes listed below or to the code search function, use the remote control supplied by the manufacturer.
Cable Box or Satellite Codes
The remote control is programmed with cable box and satellite codes for power on/off, channel up/down, and 10 key operation.
1)Find the cable box or satellite brand from the list of codes shown below.
2)Slide the 2-way selector switch to “CATV”.
3)Press and hold down the DISPLAY button, then enter the first code number listed with the 10 key pad.
4)Release the DISPLAY button, and confirm the operation of the cable box/satellite receiver.
•If your cable or satellite box does not respond to the first code, try the others listed. If it does not respond to any code, try the search codes function, on page 28.
Cable Box |
Codes |
Cable Box |
Codes |
Digital |
Codes |
|
|
|
|
|
|
|
|
ABC |
024 |
Puser |
032 |
Satellite |
|
|
Systems |
|
|||||
Archer |
032, 025 |
RCA |
061, 070 |
Echostar |
100, 113, 114, |
|
|
|
|
|
|||
Cableview |
051, 032 |
Realistic |
032 |
(Dish Network) |
115 |
|
|
|
|
|
|||
Citizen |
022, 051 |
Regal |
058, 064, 040, |
|
|
|
Express VU |
100, 113 |
|||||
|
|
|
041, 042, 045, |
|||
Curtis |
058, 059 |
|
|
|
||
|
068 |
G.E. |
106 |
|||
|
|
|
||||
Diamond |
024, 032, 025 |
|
||||
Regency |
034 |
|
|
|||
|
|
G.I. |
108, 120, 121, |
|||
Eagle |
029 |
|||||
Rembrandt |
037, 032, 051, |
|
122 |
|||
|
|
|
||||
Eastern |
034 |
|
||||
|
038 |
|
|
|||
|
|
|
|
|
||
GC Brand |
032, 051 |
|
|
Gradiente |
112 |
|
Samsung |
051 |
|||||
Gemini |
022, 043 |
|
|
|
|
|
Scientific Atlanta |
057, 058, 059 |
Hitachi |
104, 111 |
|||
|
|
|||||
General |
065, 024, 025, |
|||||
|
|
|
|
|||
SLMark |
051, 047 |
HNS (Hughes) |
104 |
|||
Instrument/Jerrold |
026, 027, 020, |
|||||
|
021, 022, 057, |
Sprucer |
051, 056 |
Magnavox |
102, 103 |
|
|
023, 072, 074 |
|
|
|||
|
Stargate |
032, 051 |
|
|
||
|
Panasonic |
105 |
||||
Hamlin |
040, 041, 042, |
|
|
|||
Telecaption |
067 |
|
|
|||
|
045, 058, 064 |
Philips |
102, 103, 116 |
|||
|
|
|
||||
Hitachi |
049, 024 |
Teleview |
047, 051 |
|
|
|
Primestar |
108 |
|||||
|
|
|
|
|||
Macom |
049, 050, 051, |
Texscan |
044 |
|
|
|
Proscan |
106, 109, 110 |
|||||
|
054 |
|
|
|||
|
Tocom |
035, 036, 066, |
|
|
||
|
RCA |
106, 109, 110 |
||||
|
|
|||||
Magnavox |
033 |
|||||
|
074 |
|||||
|
|
|
||||
|
Sony |
107 |
||||
|
|
|
|
|||
Memorex |
030 |
|
|
|||
Toshiba |
050, 048 |
|
|
|||
|
|
Star Choice |
104, 108 |
|||
Movietime |
032, 051 |
|||||
|
|
|||||
Unika |
032, 025 |
|||||
|
|
|
|
|||
Oak |
039, 037, 048 |
Toshiba |
101, 104, 117, |
|||
|
|
|||||
|
|
Universal |
022, 032 |
|
118, 119 |
|
Panasonic |
055, 056, 060, |
|
||||
|
|
|
|
|||
|
071, 073 |
Videoway |
052 |
Uniden |
102, 103 |
|
Paragon |
063 |
|
|
|
|
|
Viewstar |
029, 030 |
|
|
|||
|
|
|
|
|||
Philips |
028, 029, 030, |
|
|
|
|
|
Zenith |
063, 046 |
|
|
|||
|
052, 053, 031, |
|
|
|
|
|
|
Zenith/Drake |
046 |
|
|
||
|
069 |
|
|
|||
|
Satellite |
|
|
|
||
|
|
|
|
|
||
Pioneer |
047, 062 |
|
|
|
||
|
|
|
|
|||
|
|
|
|
|
|
|
Pulsar |
051, 032 |
|
|
|
|
|
|
|
|
|
|
|
25
Remote Programming
VCR Codes
The remote control is programmed with VCR codes for power on/off, play, stop, fast-forward, rewind, pause, record, channel up/down operation.
1)Find the VCR brand from the list of codes shown below.
2)Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “VCR”.
3)Press and hold down the DISPLAY button, then enter the first code number listed with the 10 key pad.
4)Release the DISPLAY button, and confirm the operation of the VCR.
•If your VCR does not respond to the first code, try the others listed. If it does not respond to any of the codes, try the search codes function on page 28.
•After you program your remote, some VCR buttons may not work properly. If so, use the VCR’s remote.
•To record, hold down the REC button on the remote and press PLAY.
VCR |
Codes |
VCR |
Codes |
VCR |
Codes |
||
Admiral |
035 |
|
Marantz |
003, 004, 005 |
|
Samsung |
037, 060, 062, |
|
|
|
|
|
|
|
033, 089 |
Aiwa |
027, 032, 095 |
|
Marta |
064 |
|
|
|
|
|
|
|
|
|
Samtron |
089 |
Akai |
029, 072, 073, |
|
Memorex |
024, 067 |
|
||
|
|
|
|
||||
|
074 |
|
|
|
|
Sansui |
003, 026, 020, |
|
|
MGA |
038, 040, 047, |
|
|||
Audio Dynamic |
003, 005 |
|
|
048, 041, 042 |
|
|
052 |
|
|
|
|
|
|
Sanyo |
063, 067, 091, |
Bell & Howell |
063, 071 |
|
Minolta |
058, 045, 093 |
|
||
|
|
|
071 |
||||
|
|
|
|
|
|
|
|
Broksonic |
020, 026, 094 |
|
Mitsubishi |
038, 040, 047, |
|
|
|
|
|
Scott |
059, 060, 062, |
||||
Canon |
023, 025 |
|
|
048, 041, 042, |
|
||
|
|
|
|
067, 038, 040, |
|||
|
|
078, 090 |
|
|
|||
CCE |
043 |
|
|
|
|
047, 048, 026, |
|
|
Multitech |
047, 027, 062 |
|
|
|||
Citizen |
064 |
|
|
|
020 |
||
|
|
|
|
|
|||
|
NEC |
003, 004, 005, |
|
|
|||
|
|
|
|
Sears |
063, 064, 065, |
||
Craig |
063, 029, 064 |
|
|||||
|
|
|
|
000 |
|
|
066, 058 |
Curtis Mathes |
045, 024, 027, |
|
|
|
|||
|
Olympic |
024, 023 |
|
|
|
||
|
093 |
|
|
Sharp |
035, 036, 080, |
||
|
|
|
|
|
|||
|
|
Optimus |
028, 021, 035, |
|
|||
Daewoo |
043, 059, 024, |
|
|
|
088 |
||
|
|
064 |
|
|
|||
|
092 |
|
|
|
Shintom |
075 |
|
|
|
Orion |
026, 020 |
|
|||
DBX |
003, 004, 005 |
|
|
|
|
||
|
|
Signature 2000 |
027, 035 |
||||
|
|
|
Panasonic |
023, 024, 021, |
|
||
Dimensia |
045, 093 |
|
|
|
|
||
|
|
022 |
|
Singer |
075 |
||
|
|
|
|
|
|||
Emerson |
043, 026, 077, |
|
|
||||
|
Penney |
024, 058, 045, |
|
Sony |
028, 029, 030, |
||
|
061, 025, 042, |
|
|
||||
|
|
|
063, 003, 004, |
|
|
053, 054, 055 |
|
|
020, 076 |
|
|
|
|
||
|
|
|
005, 093 |
|
|
|
|
|
|
|
|
|
SV 2000 |
027 |
|
Fisher |
063, 066, 067, |
|
|
||||
|
Pentax |
058, 005, 045, |
|
||||
|
|
|
|
||||
|
065, 071, 091 |
|
|
Sylvania |
031, 023, 024, |
||
|
|
|
093 |
|
|||
|
|
|
|
|
|
027 |
|
Funai |
027, 026, 020, |
|
|
|
|
|
|
|
Philco |
031, 024, 027, |
|
|
|||
|
|
Symphonic |
027, 081 |
||||
|
000 |
|
|
023, 026, 020, |
|
||
|
|
|
|
|
|
||
|
|
|
|
Tashiro |
064 |
||
G.E. |
033, 045, 024 |
|
|
043 |
|
||
|
|
|
|
|
|||
|
|
|
|
|
|
Tatung |
003, 004, 005 |
Go Video |
037, 051, 049, |
|
Philips |
031, 023, 024, |
|
||
|
050, 089 |
|
|
086 |
|
Teac |
003, 004, 027, |
|
|
|
Pioneer |
023 |
|
|
005 |
Goldstar |
064 |
|
|
||||
|
|
|
|
|
|
Technics |
021, 022, 023, |
|
|
|
Proscan |
045, 058, 023, |
|
||
Gradiente |
083, 084, 081, |
|
|||||
|
|
024, 031, 046, |
|
|
024 |
||
|
000, 001 |
|
|
|
|
||
|
|
|
059, 060, 093, |
|
Teknika |
024, 027, 070 |
|
|
|
|
|
|
|||
Hitachi |
023, 045, 058, |
|
|
||||
|
|
033, 087 |
|
||||
|
|
|
|
|
|||
|
|
|
|
|
|||
|
093, 027, 081 |
|
Quasar |
021, 022, 023, |
|
Thomson |
033, 096 |
|
|
|
|
||||
Instant Replay |
024, 023 |
|
|
024 |
|
|
|
|
|
|
Toshiba |
059, 046, 079 |
|||
|
|
|
Radio Shack |
033, 024, 063, |
|
||
Jensen |
003 |
|
|
|
|
||
|
|
Vector Research |
005 |
||||
|
|
036, 067, 040, |
|
||||
|
|
|
|
|
|||
JVC |
003, 004, 005, |
|
|
|
|
|
|
|
|
027 |
|
Wards |
035, 036, 067, |
||
|
000, 001, 002, |
|
|
|
|||
|
|
RCA |
033, 045, 058, |
|
|
044, 064 |
|
|
006, 007 |
|
|
|
|||
|
|
|
023, 024, 031, |
|
Yamaha |
063, 003, 004, |
|
|
|
|
|
|
|||
Kenwood |
003, 004, 064, |
|
|
046, 059, 060, |
|
|
005 |
|
005 |
|
|
083, 084, 085, |
|
Zenith |
044, 082, 064, |
LG |
064 |
|
|
087, 093, 096 |
|
|
094 |
|
Realistic |
024, 063, 036, |
|
|
|
||
|
|
|
|
|
|
||
|
|
|
|
|
|
||
LXI |
027, 064, 058, |
|
|
067, 040, 027 |
|
|
|
|
065, 066, 063, |
|
|
|
|
|
|
|
067 |
|
|
|
|
|
|
Magnavox |
031, 023, 024, |
|
|
|
|
|
|
|
086 |
|
|
|
|
|
|
26
Remote Programming
DVD Codes
The remote control is programmed with DVD codes for power on/off, play, stop, fast-forward, rewind, previous/next chapter, tray open/close, and still/pause operation.
1)Find the DVD player brand from the list of codes shown below.
2)Slide the first 2-way selector switch to “TV” and the other 2-way selector switch to “DVD”.
3)Press and hold down the DISPLAY button, then enter the first code number listed with the 10 key pad.
4)Release the DISPLAY button, and confirm the operation of the DVD player.
•If your DVD player does not respond to the first code, try the others listed. If it does not respond to any of the codes, try the search codes function on page 28.
•After you program your remote, some DVD buttons may not work properly. If so, use the DVD player’s remote.
DVD Player |
Codes |
DVD Player |
Codes |
DVD Player |
Codes |
Aiwa |
043 |
Mintek |
057 |
Sharp |
028 |
|
|
|
|
|
|
Apex |
040, 054, |
Mitsubishi |
025 |
Silvania |
038 |
|
055 |
|
|
|
|
|
|
|
|
|
|
Bose |
058 |
Next Base |
056 |
SMC |
048 |
|
|
|
|
|
|
Denon |
020, 037 |
Onkyo |
041, 052 |
Sony |
024, 045, |
|
|
|
|
|
046, 047 |
|
|
|
|
|
|
Funai |
038 |
Oritron |
044 |
Technics |
020 |
|
|
|
|
|
|
Go–Video |
032 |
Panasonic |
020 |
Thomson |
021 |
Harman |
053 |
Philips |
023, 036 |
Toshiba |
023 |
Kardon |
|
|
|
|
|
Hitachi |
031 |
Pioneer |
022 |
Venturer |
051 |
|
|
|
|
|
|
JVC |
000 |
Polk Audio |
036 |
Vialta |
050 |
Kenwood |
035, 020 |
Raite |
033 |
Wave |
042 |
|
|
|
|
|
|
KLH |
051 |
RCA |
021, 026 |
Yamaha |
020, 049 |
Konka |
039 |
Sampo |
034 |
Zenith |
027, 032 |
Koss |
050 |
Samsung |
030 |
|
|
|
|
|
|
|
|
27
Loading...