GP1A05/GP1A22LC/GP1A23LC/GP1A25LC
GP1A05/GP1A22LC/
GP1A23LC/GP1A25LC
■ Features
1.Uses 3-pin connector terminal
2.High sensing accuracy ( Slit width : 0.5mm )
3.Wide gap between light emitter and detector ( 5mm )
OPIC Photointerrupter with Connector
■ Applications
1.Copiers, Printers
2.Facsimiles
* “ OPIC ” ( Optical IC ) is a trademark of SHARP Corporation. An OPIC consists of a light-detecting element and signal-processing circuit integrated onto a single chip.
■ Outline Dimensions |
(Unit : mm ) |
GP1A05
2.0 |
|
|
3.5 |
11.0 |
|
φ 3.0± 0.1Depth2.0 |
φ 4.2 ± 0.2 |
|
34.0 |
(10.4) |
7.0 |
15.0 |
Slit width 0.5 |
3.5 |
5.0 5.0 |
|
10.5 |
|
3 |
|
2 |
1 |
1 |
VCC |
|
|
|
|
|
|
2 GND |
|
3.0 7.5 |
|
|
|
|
|
3 |
VO |
|
(2.5) |
|
(2.5) |
|
|
||
C0.5 |
|
|
|
||||
φ 4.0+ 0 |
|
|
|
|
|
|
|
|
- 0.1 |
|
* Unspecified tolerances shall be as follows ; |
||||
|
|
|
|||||
|
|
1.0 |
Dimensions(d) Tolerance |
||||
|
|
|
|
d < 4.0 |
|
± 0.2 |
|
3.5 |
|
± |
4.0<=d < 16.0 |
|
± 0.3 |
||
|
5.5 |
|
|||||
12.0± 0.1 |
|
16 <= d |
|
± 0.5 |
|||
11.0± 0.1 |
|
* ( ) : Reference dimensions |
|||||
|
|
|
JAPAN AMP made |
Recommended connectors |
EI 3-pin connector 171825-3 |
on the inserted side |
|
172053-3 etc. |
GP1A23LC (Same as GP1A05 except connector )
11.0± 0.3
3 2 1
(2.5) (2.5)
5.5 ± 1.0
1 VCC
2 GND
3 VO
*( ): Reference dimensions
JAPAN SOLDERLESS TERMINAL MSG. CO., LTD. made connector BS3P-SHF-1AA
Recommended connectors on the inserted side
Housing : (H3P-SHF-AA ) etc
Terminal : (SHF-001T-0.8SS ) etc.
GP1A22LC (Same as GP1A05 except connector )
|
0.3 |
|
|
|
|
± |
|
|
|
|
11.0 |
|
|
|
MAX 2 |
3 |
2 |
1 |
|
1.0 |
|
|||
1 |
|
1 |
VCC |
|
|
|
|
||
|
|
|
2 |
GND |
|
|
|
3 |
VO |
|
(2.5) |
(2.5) |
|
|
|
* ( ) : Reference dimensions |
( 9.2 ) |
|
2 protrusion of connector |
|
|
from holder: MAX.1.0 |
|
1.0 |
1 JAPAN SOLDERLESS |
|
TERMINAL MSG. CO., |
|
|
± |
|
|
LTD. made connector |
|
|
5.5 |
|
|
B3P-SHF-1AA |
|
|
|
|
|
|
Recommended connectors |
|
|
on the inserted side |
|
|
Housing : H3P-SHF-AA |
|
|
Terminal : SHF-001T-0.8SS |
|
|
etc. |
GP1A25LC (Same as GP1A05 except connector ) |
11.0± 0.3
2
3 |
1 |
|
(2.5) (2.5)
(5.9)
(9.9)
1VCC
2GND
3VO
*( ) : Reference dimensions
MOLEX JAPAN CO., LTD. made connector 5267-03A
Recommended connectors on the inserted side Housing : 5264-03 Terminal : 5263PBT
Recommended connectors on the inserted side are show on the following 3rd page.
“In the absence of confirmation by device specification sheets, SHARP takes no responsibility for any defects that occur in equipment using any of SHARP's devices, shown in catalogs, data books, etc. Contact SHARP in order to obtain the latest version of the device specification sheets before using any SHARP's device”.
GP1A05/GP1A22LC/GP1A23LC/GP1A25LC
Internal connection diagram ( Common to 4 models )
|
1 |
|
|
Voltage regulator |
|
|
|
|
2 |
1 |
VCC |
Amp. |
2 |
GND |
|
|
|
3 |
VO |
|
3 |
|
|
■ Absoulte Maximum Ratlngs |
|
|
(Ta = 25˚C ) |
|||||
|
|
|
|
|
|
|
|
|
|
|
Parameter |
|
Symbol |
Rating |
|
Unit |
|
|
Supply |
|
GP1A05 |
|
V CC |
- 0.5 to + 10 |
|
V |
|
voltage |
GP1A22LC / GP1A23LC / GP1A25LC |
|
- 0.5 to + 8 |
|
|||
|
|
|
|
|
||||
*1Output voltage |
|
|
V O |
- 0.5 to + 28 |
|
V |
||
*2Low level output current |
|
|
IOL |
50 |
|
mA |
||
*3Operating temperature |
|
|
T opr |
- 20 to + 75 |
|
˚C |
||
*3Storage |
GP1A05 / GP1A22LC / GP1A23LC |
|
T stg |
- 40 to + 85 |
|
˚C |
||
tempera- |
|
|
|
|
|
|||
|
GP1A25LC |
|
- 30 to + 85 |
|
||||
ture |
|
|
|
|
|
|||
*1 |
Collector-emitter voltage of output transistor |
|
|
|
|
|||
*2 |
Collector current of output transistor |
|
|
|
|
|||
*3 |
The connector should be plugged in/out at normal temperature. |
|
|
|
|
■ Electro-optical Characteristics |
|
( Unless otherwise specified, Vcc = 5V, Ta = 25˚C) |
|||||
|
|
|
|
|
|
|
|
Parameter |
Symbol |
Conditions |
MIN. |
TYP. |
MAX. |
Unit |
|
Operating supply voltage |
V CC |
|
4.5 |
- |
5.5 |
V |
|
Low level supply current |
ICCL |
Light beam uninterrupted |
- |
- |
30 |
mA |
|
Low level output voltage |
V OL |
Light beam uninterrupted,I OL= 16mA |
- |
- |
0.35 |
V |
|
High level supply current |
I CCH |
Light beam interrupted |
- |
- |
30 |
mA |
|
High level output voltage |
V OH |
Light beam interrupted,RL = 47k Ω |
V CC x 0.9 |
- |
- |
V |
|
*5 Response frequency |
f |
*4RL= 47k Ω |
- |
- |
3 000 |
Hz |
|
*4 No DC output is allowed.
*5 Response frequency is measured with the disk shown below being rotated.( Unit : mm )
Disk
0.5
.5 0
2.0