DVD Portable Player |
PVD1075/PVD1079 |
|
All version |
Service Manual
TABLE OF CONTENTS
Chapter
Technical Specification & Service Tips…………..……….. 1
Safety Instructions…………………………………………….. 2
Instruction for Use………………………………………………3
Mechanical Instructions………………………………………. 4
Troubleshooting …………………………………………………5
Overall Block Diagram………………………………………….6
Electrical Diagram……………………………………………… 7
Exploded View Diagram & Service Part List………………. 8
Revision List……………………………………………………. 9
©Copyright 2005 Philips Consumer Electronics B.V. Eindhoven, The Netherlands All rights reserved. No part of this publication may by reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronics, mechanical, photocopying, or otherwise without the prior permission of Philips
3141 785 32201
Version 1.1
1.0 TECHNICAL SPECIFICATION
General
Dimensions (W x H x D):
Weight:
Power & Battery
Power supply voltage: |
AC 100V-240V |
|
DC 9V/ 2A |
Power consumption: |
18W |
Operating temp. & RH: |
0 to +45 degC / 30 – 90% RH |
Battery voltage (Li-ion) |
7.4V |
Battery capacity |
3200mAH |
Charging time (power off) |
6 hours |
Charging time (power on) |
8 hours |
Playtime (DVB-T TV |
180mins |
receiving |
|
Audio – Earphone out (w/ 2 x 16ohm loading)
Output voltage 1kHz: |
1.5V typical |
THD 200, 1k, 1.8k, 20kHz |
0.2% typical |
Dynamic range: 1kHz |
>70dB |
Signal/Noise ratio: 1kHz |
>75dB |
Frequency response 0.2- |
+/-3dB |
20kHz): |
|
Channel Separation 1kHz |
>55dB |
Channel Balance 1kHz |
<2dB |
Audio – Speaker Out (impedance = 4)
Speaker Diameter |
41.5 +/- 0.5mm |
Output Power 1kHz |
>/= 2W |
Channel Separation 1kHz |
>30dB |
Signal/Noise ratio: 1kHz |
>62dB |
Distortion 250 – 10k Hz |
<2% |
Channel Balance 1kHz |
<3dB |
Hum |
<250uW |
Residual Signal |
< 25uW |
THD |
<2dB |
Pixel specification
Zero bright-dot & max. 3 dark-dots
1.0 TECHNICAL SPECIFICATION
Procedure on how to check the software version of the Portable TV
1.Power on the set and make sure there is no media device in it
2.Press MENU key on top of the set, and then press “1 -> 4 -> 0 -> 0” by remote control within 3 seconds (if failed, you need to retry the input process)
1.0 TECHNICAL SPECIFICATION
Procedure on how to upgrade the software of the Portable TV
For the best performance of your Portable TV. Check www.philips.com/support for latest software upgrades available.
A) MPEG firmware upgrade
1.Unzip the PHILIPS.ROM
2.Drag-n-drop to USB drive
3.Power on the main set with AC/DC adaptor
4.Insert USB drive to the USB port of the main set
5.The set will detect the updated firmware
6.Press “OK” button on remote control to confirm and proceed
7.After upgrade completed, the set will power off, and you can remove the USD drive
Warning: Do not unplug the AC adaptor during firmware upgrade to prevent flash corrupt of the set!!
B) PANEL firmware upgrade
8.Unzip the PHILIPS.ROM (different file from step 1)
9.Drag-n-drop to USB drive
10.Power on the main set with AC/DC adaptor
11.Insert USB drive to the USB port of the main set
12.The set will detect the updated firmware
13.Press “OK” button on remote control to confirm and proceed
14.After upgrade completed, the set will power off, and you can remove the USD drive
Warning: Do not unplug the AC adaptor during firmware upgrade to prevent flash corrupt of the set!!
2.0 SAFTETY INSTRUCTIONS
GB WARNING
ESD
NL WAARSCHUWING
All ICs and many other semi-conductors are susceptible to electrostatic discharges (ESD). Careless handling during repair can reduce life drastically.
When repairing, make sure that you are connected with the same potential as the mass of the set via a wrist wrap with resistance. Keep components and tools also at this potential.
Alle IC’s en vele andere halfgeleiders zijn gevoelig voor electrostatische ontladingen (ESD).
Onzorgvuldig behandelen tijdens reparatie kan de levensduur drastisch doen verminderen. Zorg ervoor dat u tijdens reparatie via een polsband met weerstand verbonden bent met hetzelfde potentiaal als de massa van het apparaat.
Houd componenten en hulpmiddelen ook op ditzelfde potentiaal.
FATTENTION
Tous les IC et beaucoup d’autres semi-conducteurs sont sensibles aux décharges statiques (ESD).
Leur longévité pourrait être considérablement écourtée par le fait qu’aucune précaution n’est prise à leur manipulation.
Lors de réparations, s’assurer de bien être relié au même potentiel que la masse de l’appareil et enfiler le bracelet serti d’une résistance de sécurité.
Veiller à ce que les composants ainsi que les outils que l’on utilise soient également à ce potentiel.
GB
DWARNUNG
Alle ICs und viele andere Halbleiter sind empfindlich gegenüber elektrostatischen Entladungen (ESD).
Unsorgfältige Behandlung im Reparaturfall kan die Lebensdauer drastisch reduzieren. Veranlassen Sie, dass Sie im Reparaturfall über ein Pulsarmband mit Widerstand verbunden sind mit dem gleichen Potential wie die Masse des Gerätes.
Bauteile und Hilfsmittel auch auf dieses gleiche Potential halten.
IAVVERTIMENTO
Tutti IC e parecchi semi-conduttori sono sensibili alle scariche statiche (ESD).
La loro longevità potrebbe essere fortemente ridatta in caso di non osservazione della più grande cauzione alla loro manipolazione.
Durante le riparazioni occorre quindi essere collegato allo stesso potenziale che quello della massa dell’apparecchio tramite un braccialetto a resistenza.
Assicurarsi che i componenti e anche gli utensili con quali si lavora siano anche a questo potenziale.
Safety regulations require that the set be restored to its original condition and that parts which are identical with those specified, be used.
“Pour votre sécurité, ces documents doivent être utilisés par des spécialistes agréés, seuls habilités à réparer votre appareil en panne”.
NL
Veiligheidsbepalingen vereisen, dat het apparaat bij reparatie in
zijn oorspronkelijke toestand wordt teruggebracht en dat onderdelen, identiek aan de gespecificeerde, worden toegepast.
CLASS 1
LASER PRODUCT
3122 110 03420
F
Les normes de sécurité exigent que l’appareil soit remis à l’état d’origine et que soient utiliséés les piéces de rechange identiques à celles spécifiées.
D
Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu beachten. Der Original zustand des Geräts darf nicht verändert werden; für Reparaturen sind Original-Ersatzteile zu verwenden.
GB Warning !
Invisible laser radiation when open.
Avoid direct exposure to beam.
SVarning !
Osynlig laserstrålning när apparaten är öppnad och spärren är urkopplad. Betrakta ej strålen.
I
Le norme di sicurezza esigono che l’apparecchio venga rimesso nelle condizioni originali e che siano utilizzati i pezzi di ricambio identici a quelli specificati.
"After servicing and before returning set to customer perform a leakage current measurement test from all exposed metal parts to earth ground to assure no shock hazard exist. The leakage current must not exceed 0.5mA."
SF Varoitus !
Avatussa laitteessa ja suojalukituksen ohitettaessa olet alttiina näkymättömälle laserisäteilylle. Älä katso säteeseen!
DK Advarse !
Usynlig laserstråling ved åbning når sikkerhedsafbrydere er ude af funktion. Undgå udsaettelse for stråling.
2.1 ESD PROTECTION
When the power supply is being turned on, you may not remove this laser cautions label. If it removes, radiation of laser
may be received.
PREPARATION OF SERVICING
Pickup Head consists of a laser diode that is very susceptible to external static electrocity. Although it operates properly after replacement, if it was subject to electrostatic discharge during replacement, its life might be shortened. When replacing, use a conductive mat, soldering iron with ground wire,etc. to protect the laser diode form damage by static electricity.
And also, the LSI and IC are same as above.
Ground conductive wrist strap for body.
Soldering iron with ground wire or ceramic type
Conductive mat
1M
The ground resistance between the ground line and the ground is less than 10
SAFTY NOTICE
SAFTY PRECAUTIONS
LEAKAGE CURRENT CHECK
Plug the AC line cord directly into a 120V AC outlet (do not use an isolation transformer for this check). Use an AC voltmeter, having 5000 per volt or more sensitivity. Connect a 1500 10W resistor,paralleled by a 0.15uF 150V AC capacitor between a knomn good earth ground (water pipe, conduit, etc.) and all exposed metal parts of cabinet (antennas, handle bracket, metal cabinet screwheads, metal overlays, control shafts, etc.).
Measure the AC voltage across the 1500 resistor. The test must be conducted with the AC switch on and then repeated with the AC switch off. The AC voltage indicated by the meter may not exceed 0.3V.A reading exceeding 0.3V indicates that a dangerous potential exists, the fault must be located and corrected. Repeat the above test with the DVD VIDEO PLAYER power plug reversed.
NEVER RETURN A DVD VIDEO PLAYER TO THE CUSTOMER WITHOUT TAKING NECESSARY CORRECTIVE ACTION.
READING SHOULD NOT EXCEED 0.3V
DVD VIDEO PLAYER |
AC VOLTMETER |
|
(5000 per volt |
||
|
||
|
or more sensitivity) |
|
|
Good earth ground |
|
1500 |
such as a water pipe, |
|
conduit, etc. |
||
10W |
|
0.15uF 150V AC
AC OUTLET
Test all exposed metal.
Voltmeter Hook-up for Leakage Current Check
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
3.0 INSTRUCTION FOR USE
4.0 MECHANICAL INSTRUCTION
A) Separate the main set into four modules
1 |
Remove the screws on panel |
|
back cabinet. |
|
|
2 |
Remove the screws on stand |
|
back cabinet. |
|
|
3 |
Open the stand back cabinet |
|
and pull out all wires |
|
connection on main board. |
|
|
4 |
Separate the stand back |
|
cabinet with main board and |
|
tuner board on it. |
|
|
4.0 MECHANICAL INSTRUCTION
5 Open the panel back cabinet and panel front cabinet, pull out the wires connection on LCD board.
6 Separate the panel front cabinet.
7 Turn to the backside of the stand front cabinet, remove two PU foams near the hinge, and remove the screws on hinge and bush hinge
8 Separate the wires and hinge, then will get the panel back cabinet
Panel back |
Stand front |
cabinet |
cabinet |
4.0 MECHANICAL INSTRUCTION
B) Separate the parts inside panel front cabinet
9 Remove the screws and separate all parts.
C) Separate the parts inside panel back cabinet
10 Remove the Key board from the panel back cabinet
11
4.0 MECHANICAL INSTRUCTION
D) Separate the parts inside stand front cabinet
12 Remove the screws on the plate metal EMI, and separate them
13 Remove the screws on the speaker bracket ear to separate them from stand front cabinet
14