PHILIPS PT927, PT927CC, PT925, PT923, PT923CC User Manual
...
PT927
PT927CC
PT925
PT923
PT923CC
PT920
PT877
PT876
PT875
PT870
User manual
1
PT927, PT927CC, PT925, PT923, PT923CC, PT920, PT877, PT876, PT875, PT870
English 6
Dansk 22 Deutsch 39
Ελληνικα 56
Español 74 Suomi 91 Français 108 Italiano 125 Nederlands 142 Norsk 159 Português 176 Svenska 193 Türkçe 210
6 English
Introduction
Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips.com/welcome.
Please read this user manual, as it contains information about the wonderful features of this shaver as well as some tips to make shaving easier and more enjoyable.
General description (Fig. 1)
A Shaver
1Protection cap
2Shaving unit
3Shaving unit release button
4Trimmer
5Trimmer release slide
6Shaver on/off button
7Shaving head symbol
8Battery symbol
BCharging stand (PT927/PT925/PT923/PT920/PT876/PT875 only)
CAdapter
DJet Clean System (PT927CC/PT923CC only)
1Locking lever
2Shaver holder
3Cleaning chamber release button
4Jet Clean System on/off button
5 Cleaning symbol and‘fluid low’ symbol
6 Battery symbol
EJet Clean solution (HQ200)
FCleaning brush
GStorage pouch (PT927CC/PT927/PT925/PT923CC/PT920/PT876 only)
Note:You can find the type number on the back of the shaver.
Important
Read this user manual carefully before you use the shaver, the Jet Clean
System (PT927CC/PT923CC only) and the charging stand (PT927/ PT925/PT923/PT920/PT876/PT875 only). Save the user manual for future reference.
Danger
-- Keep the adapter dry.
Warning
-- The adapter contains a transformer. Do not cut off the adapter to replace it with another plug, as this causes a hazardous situation.
-- The shaver and the Jet Clean System are not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of these appliances by a person responsible for their safety.
English 7
-- .Children should be supervised to ensure that they do not play with the shaver and the Jet Clean System.
-- Always unplug the shaver before you clean it under the tap.
Caution
-- Never immerse the shaver in water.
-- Never immerse the Jet Clean System or the charging stand in water nor rinse it under the tap.
-- Do not use the shaver in the bath or in the shower.
-- Never use water hotter than 80°C to rinse the shaver.
-- Be careful with hot water.Always check if the water is not too hot, to prevent your hands from getting burnt.
-- The shaver, the Jet Clean System, the charging stand and the other accessories are not dishwasher-proof.
-- Water may leak from the socket at the bottom of the shaver when you rinse it.This is normal and not dangerous because all electronics are enclosed in a sealed power unit inside the shaver.
-- Do not use the shaver, Jet Clean System, adapter, charging stand or any other part if it is damaged, as this may cause injury.Always replace a damaged adapter, charging stand or part with one of the original type.
-- Use, charge and store the shaver and the Jet Clean System at a temperature between 10°C and 35°C.
-- Always place and use the shaver and the Jet Clean System on a surface that is fluid-resistant.
-- Only use the adapter, charging stand and accessories supplied.
-- Always put the protection cap on the shaver to prevent damage and to avoid dirt accumulation in the shaving heads.
-- Only use the Jet Clean System with the original Jet Clean solution (HQ200).
-- Always place the Jet Clean System on a stable, level and horizontal surface to prevent leakage.
-- When the Jet Clean System is ready for use, do not move it to prevent leakage.
-- The Jet Clean System thoroughly cleans but does not disinfect your shaver, therefore do not share the shaver with others.
-- Empty the cleaning chamber of the Jet Clean System and clean the cleaning chamber thoroughly by rinsing it with hot tap water every 15 days.
-- If the shaver and the Jet Clean System are subjected to a major change in temperature, pressure or humidity, let them acclimatise for
30 minutes before you use them.
8 English
Compliance with standards
-- This Philips appliance complies with all applicable standards and regulations regarding exposure to electromagnetic fields (EMF) can be safely cleaned under the tap.
General
-- The appliance is equipped with an automatic voltage selector and is suitable for mains voltages ranging from 100 to 240 volts.
-- The adapter transforms 100-240 volts to a safe low voltage of less than 24 volts.
Charging
It takes approx. 1 hour to fully charge the shaver.
When you charge the shaver for the first time or after a long period of disuse, let it charge until the white battery lights up continuously.
A fully charged shaver provides up to 60 (PT927CC/PT927/ PT925/PT923/ PT923CC/PT920) or 50 shaving minutes (PT877/PT876/PT875/PT870). The shaving time may be less than 60(PT927CC/PT927/PT925/PT923/ PT923CC/PT920) or 50 shaving minutes (PT877/PT876/PT875/PT870) as a result of your shaving behaviour, your cleaning habits or your beard type.
Charge indications
Battery low
-- When the battery is almost empty (when there are only 5 or fewer shaving minutes left), the battery light starts to flash orange.
-- When you switch off the shaver, the battery light continues to flash orange for a few seconds.
Quick charging
-- When you start charging the empty battery, the battery light flashes white and orange.
Note:When the battery light flashes white and orange towards only white,you can have a quick shave of three minutes.
Charging
-- When the shaver is charging, the battery light flashes white.
English 9
Battery fully charged
-- When the battery is fully charged, the battery light lights up white continuously.
Note:After approx.30 minutes,the battery light goes out to save energy.
Charging with the adapter
Do not charge the shaver in a closed pouch (PT927CC/PT927/PT925/ PT923CC/PT923/PT920/PT877 only).
1Put the small plug in the shaver.
2Put the adapter in the wall socket.
,, The battery symbol show the charging status of the shaver (see section ‘Charge indications’ in this chapter).
Charging in the charging stand (PT927/PT925/PT923/PT920/ PT876/PT875 only)
1Put the small plug in the charging stand.
2Put the adapter in the wall socket.
3Place the shaver in the charging stand.
,, The battery symbol show the charging status of the shaver (see section ‘Charge indications’ in this chapter).
Charging in the Jet Clean System (PT927CC/PT923CC only)
1Put the small plug in the Jet Clean System.
2Put the adapter in the wall socket.
3Place the shaver without protection cap upside down in the shaver holder.
Note:The shaver cannot be placed in the Jet Clean System when the protection cap is on the shaving unit.
10 English
4 Push down the locking lever completely to lock the shaver into place.
,, The battery symbol on the Jet Clean System flashes to indicate that the shaver is being charged.
Note:When the Jet Clean System is performing the cleaning program,the battery symbol is out.
,, When the battery is fully charged, the battery symbol on the Jet Clean System lights up continuously.
Note:After approx.30 minutes,the battery symbol goes out to save energy.
5 To remove the shaver from the Jet Clean System, move the locking lever upwards until it does not go any further and remove the shaver.
Using the shaver
Note:You can also use the appliance directly from the mains.Simply connect the shaver to the mains.
Shaving
1 Press the on/off button once to switch on the shaver.
2 Move the shaving heads over your skin. Make circular movements.
-- Your skin may need 2 or 3 weeks to get accustomed to the Philips shaving system.
3 Press the on/off button once to switch off the shaver.
4 Clean the shaver (see chapter ‘Cleaning and maintenance’).
Trimming
You can use the trimmer to groom your sideburns and moustache.
1 Press the on/off button once to switch on the shaver.
English 11
2Push the trimmer slide downwards to open the trimmer. ,, You can now start trimming.
3After trimming, close the trimmer and switch off the shaver.
Cleaning and maintenance
Never use compressed air, scouring pads, abrasive cleaning agents or aggressive liquids such as petrol or acetone to clean the shaver, the charging stand (PT927/PT925/PT923/PT920/PT876/PT875 only) and the Jet Clean System (PT927CC/PT923CC only).
-- The best and most hygienic way to clean the shaver is in the Jet Clean System (PT927CC/PT923CC only).You can also rinse the shaver under the tap or clean it with the cleaning brush supplied.
-- Clean the shaver after every shave for optimal shaving performance. -- Regular cleaning guarantees better shaving performance.
-- For the best cleaning results, we advise you to use the Philips Cleaning spray (HQ110) and (PT927CC/PT923CC only) the Jet Clean solution (HQ200).
-- Be careful with hot water.Always check if the water is not too hot, to prevent your hands from getting burnt.
Note:Water may leak from the socket at the bottom of the shaver when you rinse it.This is normal and not dangerous because all electronics are enclosed in a sealed power unit inside the shaver.
Cleaning the shaving unit under the tap
1Switch off the shaver and disconnect it from the mains.
2Press the release button to open the shaving unit.
3Rinse the shaving unit and hair chamber under a hot tap for 30 seconds.
Be careful with hot water.Always check if the water is not too hot, to prevent your hands from getting burnt.
12 English
-- Rinse the hair chamber and the inside of the shaving unit.
-- Rinse the outside of the shaving unit.
4 Close the shaving unit and shake off excess water.
Be careful not to hit the shaving unit against anything while shaking off excess water.
Never dry the shaving unit and the hair chamber with a towel or tissue, as this may damage the shaving heads and the coupling spindles.
5Open the shaving unit again and leave it open to let the shaver dry completely.
Cleaning the shaving unit with the cleaning brush
1 Switch off the shaver and disconnect it from the mains. 2 Press the release button to open the shaving unit.
3 Pull the shaving unit off the shaver.
|
4 Turn the lock anticlockwise (A) and remove the retaining frame (B). |
|
English 13
5Remove and clean one shaving head at a time. Each shaving head consists of a cutter and a guard.
Note:Do not clean more than one cutter and guard at a time,since they are all matching sets.If you accidentally mix up the cutters and guards,it may take several weeks before optimal shaving performance is restored.
-- Remove the cutter from the shaving guard and clean it with the brush.
-- Clean the inside and outside of the shaving guard with the brush.
6 Put the shaving heads back into the shaving unit.
Note:Make sure that the projections of the shaving heads fit exactly into the recesses.
7Put the retaining frame back into the shaving unit (A)and turn the lock clockwise (B).
8Insert the lug of the shaving unit into the slot in the top of the shaver. Then close the shaving unit.
Note:If the shaving unit does not close smoothly,check if you have inserted the shaving heads properly and if the retaining frame is locked.
14 English
Cleaning the shaving unit in the Jet Clean System (PT927CC/PT923CC only)
The Jet Clean System cleans the shaving unit.
Preparing the Jet Clean System for use
Note:Fill the cleaning chamber before first use and when the‘fluid low’symbol flashes to indicate that the fluid level is too low.When the fluid level drops below the minimum level,the cleaning symbol and the‘fluid low’symbol start to flash and the shaver holder returns to its starting position
1
,,
2
3
Simultaneously press the release buttons on both sides of the cleaning chamber (A).Then lift the Jet Clean System off the cleaning chamber (B).
The cleaning chamber remains behind.
Unscrew the cap from the bottle with Jet Clean solution (HQ200) and remove the airtight seal.
Fill the cleaning chamber with Jet Clean solution (HQ200) up to the MAX indication.
Note:Make sure the cleaning chamber is always filled above the MIN indication.
4 Place the Jet Clean System back onto the cleaning chamber (‘click’).
Make sure that the release buttons snap back into place.
When the cleaning chamber is filled with Jet Clean solution, do not move it to prevent leakage.
5Put the small plug in the Jet Clean System and put the adapter in the wall socket.
,, The shaver holder automatically moves to its highest position.
The Jet Clean System is now ready for use.
Using the Jet Clean System
1Place the shaver without protection cap upside down in the shaver holder. Push down the locking lever completely to lock the shaver into place.
,, The battery symbol on the Jet Clean System goes on to indicate that the shaver is being charged.
Note:The shaver cannot be placed in the Jet Clean System when the protection cap is on the shaving unit.
English 15
2Press the on/off button on the Jet Clean System to start the cleaning program.
,, The battery symbol on the Jet Clean System goes out.
,, During the cleaning program,the cleaning symbol starts to flash and the shaver is automatically lowered into the cleaning fluid.
,, The shaver automatically switches on and off several times and moves up and down.
,, The cleaning symbol flashes throughout the cleaning program,which takes approx. 8 minutes.
,, After the cleaning program, the battery symbol on the Jet Clean System goes on to indicate that the shaver is being charged.
Note:If you press the on/off button of the Jet Clean System during the cleaning program, the program aborts and resets.In this case,the cleaning stops flashing and the shaver holder returns to its starting position.The shaver may still be wet and dirty,because the cleaning program has not been finished.
Note:If you remove the adapter from the wall socket during the cleaning program,the program aborts.The shaver holder remains in its current position. When you put the adapter back into the wall socket, the shaver holder moves to its highest position.
Note:When the fluid level drops below the minimum level,the cleaning symbol and the‘fluid low’symbol start to flash with intervals and the shaver holder returns to its starting position
Cleaning the Jet Clean System
Empty the cleaning chamber and clean it thoroughly by rinsing it with hot tap water every 15 days if you use the Jet Clean System daily. Otherwise empty and clean the cleaning chamber at least once a month.
1 Clean the outside of the Jet Clean System with a moist cloth.
Never immerse the Jet Clean System in water, nor rinse it under the tap.
2 Simultaneously press the release buttons on both sides of the Jet Clean System (A).Then lift the Jet Clean System off the cleaning chamber (B).
,, The cleaning chamber remains behind.
3 Pour any remaining cleaning fluid out of the cleaning chamber.
You can simply pour the cleaning fluid down the sink, this is not harmful to the environment.
4 Rinse the cleaning chamber under a hot tap.
Be careful with hot water.Always check if the water is not too hot, to prevent your hands from getting burnt.
The cleaning chamber is not dishwasher-proof.
16 English
5 Fill the cleaning chamber with Jet Clean solution (HQ200) up to the MAX indication.
Note:Make sure the cleaning chamber is always filled above the MIN indication.
6 Place the Jet Clean System back onto the cleaning chamber (‘click’).
Make sure that the release buttons snap back into place.
Cleaning the trimmer with the cleaning brush
Clean the trimmer every time you have used it.
1 Switch off the shaver and disconnect it from the mains. 2 Push the trimmer slide downwards to open the trimmer.
3Clean the trimmer with the short-bristled side of the cleaning brush. Brush up and down along the trimmer teeth.
4Close the trimmer (‘ click’).
Tip:For optimal trimming performance,lubricate the trimmer teeth with a drop of sewing machine oil every six months.
English 17
Storage
There are several ways to store the shaver or to take it with you when you travel:
-- Put the protection cap on the shaver after use to prevent damage and to avoid dirt accumulation in the shaving heads.
-- Store the shaver in the pouch supplied (PT927CC/PT927/PT925/ PT923CC/PT923/PT920/PT876 only).
-- Store the shaver in the charging stand (PT927/PT923/PT920/PT876/ PT875 only).
-- Put the shaver in the Jet Clean System (PT927CC/PT923CC only).
Make sure the protection cap is not on the shaving unit.
Note:If you do not want the shaver to charge while it is stored it in the Jet Clean System,just leave the locking lever in upright position.
Replacement
For maximum shaving performance, we advise you to replace the shaving heads every two years.
Replacement reminder
The shaving head symbol will light up to indicate that the shaving heads need to be replaced. Replace damaged shaving heads right away.
Only replace the shaving heads with original HQ9 Philips Shaving Heads (PT927CC/PT927/PT925/PT923CC/PT923/PT920) or HQ8 Philips Shaving Heads (PT877/PT876/PT875/PT870).
1The shaving head symbol lights up orange continuously.
2Switch off the shaver. Disconnect the shaver from the mains and remove it from the Jet Clean System (PT927CC/PT923CC).
3Press the release button to open the shaving unit.
4Pull the shaving unit off the shaver.
5Turn the lock anticlockwise (A) and remove the retaining frame (B).
6Remove the shaving heads and place new ones in the shaving unit.
18 English
Note:Make sure that the projections of the shaving heads fit exactly into the recesses.
7 Put the retaining frame back into the shaving unit (A) and turn the lock clockwise (B).
8 Insert the lug of the new shaving unit into the slot in the top of the shaver.Then close the shaving unit.
Note:If the shaving unit does not close smoothly,check if you have inserted the shaving heads properly and if the retaining frame is locked.
9 Press and hold the on/off button for 5 seconds to reset the replacement reminder on the shaver.The orange light goes out.
5 sec.
English 19
Ordering accessories
To retain the top performance of your shaver, make sure you clean it regularly and replace its shaving heads at the recommended time.
Shaving heads
-- We advise you to replace your shaving heads every two years. Always replace with HQ9 Philips Shaving Heads (PT927CC/PT927/PT925/ PT923CC/PT923/PT920) or HQ8 Philips Shaving Heads (PT877/ PT876/PT875/PT870).
Cleaning
-- PT927CC/PT923CC only: use Jet Clean solution (HQ200) for regular cleaning of the shaving heads.
-- Use Cleaning spray (HQ110) to clean the shaving heads thoroughly.
Environment
-- Do not throw away the shaver and the Jet Clean System (PT927CC/ PT923CC only) with the normal household waste at the end of their life, but hand them in at an official collection point for recycling. By doing this, you help to preserve the environment.
-- The built-in rechargeable shaver battery contains substances that may pollute the environment. Always remove the battery before you discard or hand in the shaver at an official collection point. Dispose of the battery at an official collection point for batteries. If you have trouble removing the battery, you can also take the appliance to a
Philips service centre.The staff of this centre will remove the battery for you and will dispose of it in an environmentally safe way.
Removing the rechargeable shaver battery
Only remove the rechargeable battery when you discard the shaver. Make sure the rechargeable battery is completely empty when you remove it.
1Disconnect the shaver from the mains, remove it from the Jet Clean
System (specific types only) or remove it from the charging stand (specific types only).
2Let the shaver operate until it stops.
3Undo the screws in the back of the shaver and in the hair chamber.
4Remove the front panel and the back panel.
5Bend the 6 hooks aside and take out the power unit.
20 English
Be careful, the hooks are sharp. 6 Remove the battery.
Be careful, the battery strips are sharp.
Do not put the shaver back into the plugged-in Jet Clean System
(specific types only) or charging stand (specific types only) after you have removed the rechargeable battery.
Do not connect the shaver to the mains again after you have removed the rechargeable battery.
Guarantee and support
If you need information or support, please visit www.philips.com/ support or read the worldwide guarantee leaflet.
Guarantee restrictions
The shaving heads (cutters and guards) are not covered by the terms of the international guarantee because they are subject to wear.
Troubleshooting
This chapter summarises the most common problems you could encounter with the appliance. If you are unable to solve the problem with the information below, visit www.philips.com/support for a list of frequently asked questions or contact the Consumer Care Centre in your country.
Problem |
Possible cause |
Solution |
|
|
|
The shaver does |
The Jet Clean System (PT927CC/ |
Clean the shaver thoroughly before you |
not shave as well |
PT923CC only) has not cleaned the |
continue shaving. If necessary, clean and |
as it used to. |
shaver properly because the cleaning |
refill the cleaning chamber (see chapter |
|
fluid in the cleaning chamber is soiled |
‘Cleaning and maintenance’). |
|
or the cleaning fluid level is too low. |
|
The shaving heads are damaged or worn.
Long hairs obstruct the shaving heads.
Replace the shaving heads (see chapter
‘Replacement’).
Clean the shaving heads one by one (see section ‘Cleaning the shaving unit with the cleaning brush’ in chapter‘Cleaning and maintenance’).
|
You have not inserted the shaving |
|
heads properly. |
The shaver does |
The rechargeable battery is empty. |
not work when I |
|
press the on/off |
|
button. |
|
Make sure that the projections of the shaving heads fit exactly into the recesses (see section‘Cleaning and maintenance’).
Recharge the battery (see chapter
‘Charging’) or connect the shaver to the mains.
|
|
English 21 |
Problem |
Possible cause |
Solution |
|
|
|
|
The temperature of the shaver is too |
As soon as the temperature of the shaver |
|
high. In this case, the shaver does not |
has dropped sufficiently, you can switch |
|
work. |
on the shaver again. |
The shaver is not |
The cleaning fluid in the cleaning |
Empty and rinse the cleaning chamber |
entirely clean after |
chamber is soiled. |
(see chapter‘Cleaning and maintenance’). |
I clean it in the |
|
|
Jet Clean System |
|
|
(PT927CC/ |
|
|
PT923CC only). |
|
|
The cleaning fluid level is too low. If the fluid volume in the cleaning chamber drops below the minimum
level during the cleaning program, the program aborts.The cleaning symbol and the‘fluid low’ symbol flash at intervals and the holder returns to its starting position.
Refill the cleaning chamber with cleaning fluid up to the MAX level (see chapter ‘Cleaning and maintenance’).
|
You have used another cleaning fluid |
|
than the original Philips cleaning fluid. |
|
You have not closed the locking lever |
|
of the Jet Clean System properly, or |
|
you have not placed the shaver in the |
|
Jet Clean Shaver properly. In these |
|
cases the Jet Clean System starts to |
|
operate, but the cleaning program is |
|
not performed properly. |
The Jet |
The Jet Clean System is not connected |
Clean System |
to the mains. |
(PT927CC/ |
|
PT923CC |
|
only) does not |
|
work when I press |
|
the on/off button. |
|
Only use Jet Clean solution HQ200.
Place the shaver without protection cap in the Jet Clean System properly. Close the locking lever properly.
Put the small plug in the Jet Clean System and put the adapter in the wall socket.
Water leaks from |
This is normal and not dangerous. |
the shaver after |
|
cleaning. |
|
During rinsing some water may collect between the power unit and the housing.
After rinsing this water flows out through the socket.The power unit is completely watertight so water cannot reach the electronic parts of the shaver.Your shaver continues to be absolutely safe.
22 Dansk
Introduktion
Tillykke med dit køb og velkommen til Philips! For at få fuldt udbytte af den support, Philips tilbyder, skal du registrere dit produkt på www.philips.com/ welcome.
Vi beder dig læse brugervejledningen igennem, da den indeholder oplysninger om shaverens unikke funktioner og tips til at gøre barbering nemmere og sjovere.
Generel beskrivelse (fig. 1)
A Shaver
1Beskyttelseskappe
2Skærhoved
3Udløserknap til skærhoved
4Trimmer
5Udløser til trimmer
6Shaver tænd/sluk-knap
7Shaverhovedsymbol
8Batterisymbol
BOpladeenhed (kun PT927/PT925/PT923/PT920/PT876/PT875)
CAdapter
DJet Clean-system (PT927CC/PT923CC)
1Låseklemme
2Holder til shaver
3Udløserknap til rensekammer
4Tænd/sluk-knap til Jet Clean-systemet
5Rengøringssymbol og symbol for “lav væskestand”
6Batterisymbol
EJet Clean Solution (HQ200)
FRensebørste
GOpbevaringsetui (kun PT927CC/PT927/PT925/PT923CC/PT920/ PT876)
Bemærk:Du kan finde typenummeret bag på shaveren.
Vigtigt
Læs denne brugervejledning grundigt, før du tager shaveren, Jet Cleansystemet (kun PT927CC/PT923CC) og opladeenheden (kun PT927/ PT925/PT923/PT920/PT876/PT875) i brug. Gem brugervejledningen til senere brug.
Fare
-- Hold adapteren tør.
Advarsel
-- Adapteren indeholder en transformer. Adapteren må ikke klippes af og udskiftes med et andet stik, da dette vil forårsage en farlig situation.
-- Shaveren og Jet Clean-systemet er ikke beregnet til at blive brugt af personer (herunder børn) med nedsatte fysiske og mentale evner, nedsat følesans eller manglende erfaring og viden, medmindre de er blevet vejledt eller instrueret i disse apparaters anvendelse af en person, der er ansvarlig for deres sikkerhed.
Dansk 23
-- Shaveren og Jet Clean-systemet bør holdes uden for børns rækkevidde for at sikre, at de ikke kan komme til at lege med apparaterne.
-- Tag altid stikket ud af shaveren, inden den skylles under vandhanen.
Forsigtig
-- Kom aldrig shaveren ned i vand.
-- Kom aldrig Jet Clean-systemet eller opladeenheden ned i vand, og undgå at skylle dem under hanen.
-- Brug ikke shaveren i badet eller under bruseren.
-- Rens aldrig shaveren med vand, der er varmere end 80°C.
-- Vær forsigtig med varmt vand. Kontroller altid, at vandet ikke er for varmt, så du ikke skolder dine hænder.
-- Shaveren, Jet Clean-systemet, opladeenheden og det øvrige tilbehør tåler ikke opvaskemaskine.
-- Når shaveren rengøres, kan der dryppe lidt vand ud af stikket i bunden. Dette er helt normalt og ganske ufarligt, da al elektronikken er indkapslet i en forseglet motorenhed inde i shaveren.
-- Brug ikke shaveren, Jet Clean-systemet, adapteren, opladeenheden eller det øvrige tilbehør, hvis det er beskadiget, da dette kan forårsage personskade. Du skal altid erstatte en beskadiget adapter, opladeenhed eller anden del med en tilsvarende original type.
-- Brug, oplad og opbevar din shaver og Jet Clean-systemet ved en temperatur mellem 10°C og 35°C.
-- Du skal altid placere og bruge shaveren og Jet Clean-systemet på et underlag, der kan tåle at blive vådt.
-- Brug kun den medfølgende adapter og opladeenhed og det medfølgende tilbehør.
-- Sæt altid beskyttelseskappen på shaveren for at undgå skader og ophobning af støv i skærene.
-- Brug kun Jet Clean-systemet med den originale Jet Clean Solution (HQ200).
-- Placer altid Jet Clean-systemet på et stabilt, plant og vandret underlag for at undgå lækage.
-- For at undgå udsivende væske må Jet Clean-systemet ikke flyttes, når det er klar til brug.
-- Jet Clean-systemet renser din shaver meget grundigt, men desinficerer den ikke. Derfor bør du ikke dele shaveren med andre.
-- Tøm Jet Clean-systemets rensekammer, og rengør rensekammeret grundigt ved at sætte det under den varme hane hver 15. dag.
-- Hvis shaveren og Jet Clean-systemet udsættes for store temperatursvingninger, tryk eller fugtighed, skal du lade det akklimatisere sig i 30 minutter, inden det tages i brug.
24 Dansk
Overholdelse af standarder
-- Dette Philips-apparat overholder alle gældende standarder og regler angående eksponering for elektromagnetiske felter (EMF) og kan skylles under rindende vand uden risiko.
Generelt
-- Apparatet er udstyret med automatisk spændingstilpasning til netspændinger mellem 100 og 240 volt.
-- Adapteren omformer 100 - 240 Volt til en sikker lavspænding under 24 Volt.
Opladning
Det tager ca. 1 time at oplade shaveren helt.
Når shaveren oplades for første gang eller efter en længere pause, skal den oplades, indtil den hvide batteriindikator lyser konstant.
En fuldt opladet shaver giver op til 60 (PT927CC/PT927/PT925/PT923/ PT923CC/PT920) eller 50 minutters barbering (PT877/PT876/PT875/ PT870).
Brugstiden kan være kortere end 60 (PT927CC/PT927/PT925/PT923/ PT923CC/PT920) eller 50 minutters barbering (PT877/PT876/PT875/
PT870) afhængigt af dine barberingsvaner, rensevaner eller din skægtype.
Opladningsindikatorer
Lavt batteriniveau
-- Når batteriet næsten er afladet (når der kun er 5 minutter eller færre tilbage til barbering), blinker batteriindikatoren orange.
-- Når du slukker for shaveren, forsætter batteriindikatoren med at blinke orange i nogle sekunder.
Lynopladning
-- Når du oplader det tomme batteri, blinker batteriindikatoren hvidt og orange.
Bemærk:Når batteriindikatoren blinker hvidt og orange og begynder kun at blinke hvidt,kan du få en hurtig barbering på tre minutter.
Opladning
-- Når shaveren oplades, blinker batteriindikatoren hvidt.
Dansk 25
Batteri fuldt opladet
-- Når batteriet er fuldt opladet, lyser batteriindikatoren konstant hvidt.
Bemærk:Efter ca.30 minutter slukker batteriindikatoren for at spare på energien.
Opladning med adapter
Shaveren må ikke oplades i et lukket etui (kun PT927CC/PT927/PT925/ PT923CC/PT923/PT920/PT877).
1Sæt det lille stik i shaveren.
2Slut adapteren til stikkontakten.
,, Batterisymbolet viser opladningsstatus for shaveren (se afsnittet “Opladningsindikatorer” i dette kapitel).
Opladning i opladeenheden (kun PT927/PT925/PT923/PT920/ PT876/PT875)
1Sæt det lille stik i opladeenheden.
2Slut adapteren til stikkontakten.
3Placér shaveren i opladeenheden.
,, Batterisymbolet viser opladningsstatus for shaveren (se afsnittet “Opladningsindikatorer” i dette kapitel).
Opladning i Jet Clean-systemet (kun PT927CC/PT923CC)
1Sæt det lille stik i Jet Clean-systemet.
2Slut adapteren til stikkontakten.
3Placer shaveren på hovedet i holderen uden beskyttelseskappe.
Bemærk:Shaveren kan ikke sættes i Jet Clean-systemet med påsat beskyttelseskappe.
26 Dansk
4 Skub låseklemmen helt ned for at låse shaveren fast
,, Batterisymbolet på Jet Clean-systemet blinker for at vise, at shaveren er ved at blive opladet.
Bemærk:Når Jet Clean-systemet udfører renseprogrammet,er batterisymbolet slukket.
,, Når batteriet er fuldt opladet, lyser batterisymbolet på Jet Cleansystemet konstant.
Bemærk:Efter ca.30 minutter slukker batterisymbolet for at spare på energien.
5 Du fjerner shaveren fra Jet Clean-systemet ved at trykke låseklemmen opad, så langt den kan komme, og fjerne shaveren.
Brug af shaveren
Bemærk:Du kan også anvende apparatet med strøm fra stikkontakten.Du skal blot tilslutte shaveren til stikkontakten.
Barbering
1 Tryk én gang på tænd/sluk-knappen for at tænde for shaveren.
2 Bevæg skærhovederne hen over huden i cirkulære bevægelser.
-- Vær opmærksom på, at der kan gå 2-3 uger, før din hud helt har vænnet sig til Philips’ barberingssystem.
3 Tryk én gang på tænd/sluk-knappen for at slukke for shaveren. 4 Rengør shaveren (se afsnittet “Rengøring og vedligeholdelse”).
Dansk 27
Trimning
Trimmeren kan bruges til pleje af bakkenbarter og moustache.
1Tryk én gang på tænd/sluk-knappen for at tænde for shaveren.
2Tryk trimmerens skydekontakt nedad for at åbne trimmeren. ,, Trimningen kan nu påbegyndes.
3Efter trimning skal du lukke trimmeren og slukke for shaveren.
Rengøring og vedligeholdelse
Brug aldrig trykluft, skuresvampe, slibende rengøringsmidler eller skrappe væsker som f.eks. benzin, acetone eller lignende til rengøring af shaveren, opladeenheden (kun PT927/PT925/PT923/PT920/PT876/PT875) og Jet Clean-systemet (kun PT927CC/PT923CC).
-- Den bedste og mest hygiejniske måde at rengøre shaveren på er ved hjælp af Jet Clean-systemet (kun PT927CC/PT923CC). Men shaveren kan også skylles under vandhanen eller rengøres med den medfølgende børste.
-- Rengør shaveren efter hver barbering for at bevare den optimale barberingsevne.
-- Regelmæssig rengøring sikrer det bedste barberingsresultat.
-- For at opnå det bedste rengøringsresultat anbefaler vi, at du bruger
Philips Cleaning Spray (HQ110) og (kun PT927CC/PT923CC) Jet Clean Solution (HQ200).
-- Vær forsigtig med varmt vand. Kontroller altid, at vandet ikke er for varmt, så du ikke skolder dine hænder.
Bemærk:Når shaveren rengøres,kan der dryppe lidt vand ud af stikket i bunden.Dette er helt normalt og ganske ufarligt,da al elektronikken er indkapslet i en forseglet motorenhed inde i shaveren.
28 Dansk
Rengøring af skærhovedet under rindende vand
1 Sluk for shaveren, og tag den ud af stikket.
2 Tryk på udløserknappen og luk skærhovedet op.
3 Skyl skærhovedet og skægkammeret i varmt rindende vand i
30 sekunder.
Vær forsigtig med varmt vand. Kontroller altid, at vandet ikke er for varmt, så du ikke skolder dine hænder.
-- Rens skægkammeret og indersiden af skærhovedet.
-- Skyl skærhovedets yderside.
4 Luk skærhovedet, og ryst overskydende vand væk.
Pas på, at skærhovedet ikke støder mod andre ting, når du ryster overskydende vand væk.
Skærhovedet og skægkammeret må ikke tørres med et håndklæde eller køkkenrulle, da dette kan beskadige skærene og koblingsakslerne.
5Åbn skærhovedet igen, og lad det stå åbent, indtil shaveren er helt tør.
Rengøring af skærhovedet med rengøringsbørsten
1 Sluk for shaveren, og tag den ud af stikket.
2 Tryk på udløserknappen og luk skærhovedet op.
3 Træk skærhovedet af shaveren.
Dansk 29
|
4 Drej låsen mod uret (A), og tag samlerammen af (B). |
|
5 Fjern og rens et skær ad gangen. Hvert skær består af en kniv og en lamelkappe.
Bemærk:Rens kun ét skær ad gangen,da knive og lamelkapper er slebet parvis.Kommer man ved en fejltagelse til at blande knive og lamelkapper,kan det tage flere uger,før shaveren igen barberer optimalt.
-- Tag skærene ud af skærkappen, og rengør dem med børsten.
-- Rengør inderog yderside af skærkappen med børsten.
6 Sæt skærene tilbage i skærhovedet.
Bemærk:Sørg for,at de små tappe passer præcist ned i recesserne.
7 Sæt samlerammen tilbage i skærhovedet (A), og drej den med uret (B).
30 Dansk
8 Placer tappen på skærhovedet i rillerne øverst på shaveren. Luk derefter skærhovedet.
Bemærk:Hvis skærhovedet ikke lukker uden modstand,skal du kontrollere,at du har placeret skærene korrekt,og at samlerammen er låst.
Rengøring af skærhovedet i Jet Clean-systemet (kun PT927CC/
PT923CC)
Jet Clean-systemet renser skærhovedet.
Klargøring af Jet Clean-systemet
Bemærk:Fyld rensekammeret,inden du bruger modulet første gang,og når “lav væskestand”blinker for at indikere,at væskestanden er for lav.Når væskeniveauet er under minimumsmarkeringen,begynder rengøringssymbolet og symbolet for“lav væskestand”at blinke,og shaverens holder vender tilbage til startposition.
1Tryk samtidigt på udløserknapperne på begge sider af rensekammeret (A). Løft derefter Jet Clean-systemet af rensekammeret (B).
,, Rensekammeret bliver tilbage.
2 Skru låget af flasken med Jet Clean Solution (HQ200),og fjern den lufttætte lukning.
3 Fyld rensekammeret med Jet Clean Solution (HQ200) op til MAXmærket.
Bemærk:Sørg for,at rensekammeret altid er fyldt til op over MIN-mærket.
4 Sæt Jet Clean-systemet tilbage på rensekammeret (“klik”).
Kontrollér, at udløserknapperne klikker tilbage på plads.
For at undgå udsivende væske må rensekammeret ikke flyttes,når det er fyldt med Jet Clean Solution.
5 Sæt det lille stik i Jet Clean-systemet, og sæt adapteren i en stikkontakt.
,, Shaverens holder flyttes automatisk til højeste indstilling.
Jet Clean-systemet er nu klar til brug.
Loading...