Mitsubishi GT25-05PCO-2, GT25-05PCO, GT21-07WPCO, GT21-10WPCO, GT20-15PCO User Manual

GOT2000 Series Protective Cover for Oil

for GT27/GT25/GT23/GT2107

User's Manual

GT20-15PCO GT25-05PCO GT20-12PCO GT25-05PCO-2 GT20-10PCO GT25T-07WPCO GT20-08PCO

GT21-10WPCO

GT21-07WPCO

Thank you for choosing Mitsubishi Electric Graphic Operation Terminal (GOT).

Prior to use, please read both this manual and detailed manual thoroughly to fully understand the product.

MODEL GT20/GT25-PCO-U-JE

MODEL

CODE 1D7MH8

IB(NA)-0800498-E(1903)MEE

© 2013 MITSUBISHI ELECTRIC CORPORATION

SAFETY PRECAUTIONS

(Always read these precautions before using this equipment.)

Before using this product, please read this manual and the relevant manuals introduced in this manual carefully and pay full attention to safety to handle the product correctly.

The precautions given in this manual are concerned with this product.

In this manual, the safety precautions are ranked as "WARNING" and "CAUTION".

WARNING	Indicates that incorrect handling may cause hazardous
	conditions, resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous

CAUTION conditions, resulting in medium or slight personal injury or physical damage.

Note that the CAUTION level may lead to a serious accident according to the circumstances.

Always follow the precautions of both levels because they are important to personal safety.

Please save this manual to make it accessible when required and always forward it to the end user.

[MOUNTING PRECAUTIONS]

WARNING

Be sure to shut off all phases of the external power supply used by the system before mounting or removing the GOT main unit to/from the panel.

Not doing so can cause the unit to fail or malfunction.

CAUTION

When mounting the GOT to the control panel, tighten the mounting screws in the specified torque range.

Undertightening can cause the GOT to drop, short circuit or malfunction. Overtightening can cause a drop, short circuit or malfunction due to the damage of the screws or the GOT.

[STARTUP AND MAINTENANCE PRECAUTIONS]

CAUTION

Daily check the protective cover for oil with eyes.

When you find extreme dirt or scratches on the surface, immediately replace it with new one.

Using the protective cover for oil with decreased visibility may cause malfunction.

[DISPOSAL PRECAUTIONS]

CAUTION

 When disposing of this product, treat it as industrial waste.

[TRANSPORTATION PRECAUTIONS]

CAUTION

When fumigants that contain halogen materials such as fluorine, chlorine, bromine, and iodine are used for disinfecting and protecting wooden packaging from insects, they cause malfunction when entering our products. Please take necessary precautions to ensure that remaining materials from fumigant do not enter our products, or treat packaging with methods other than fumigation (heat method).

Additionally, disinfect and protect wood from insects before packing products.

Manuals

The following shows manuals relevant to this product.

	Manual name	Manual number
		(Model code)
	GOT2000 Series User's Manual (Hardware)	SH-081194ENG
	(Sold separately)	(1D7MJ5)

For detailed manuals and relevant manuals, refer to the e-Manual or PDF manuals stored in the DVD-ROM for the screen design software used.

The latest manuals are also available from MITSUBISHI ELECTRIC FA Global Website (www.MitsubishiElectric.com/fa).

Packing List

The following items are included.

Model	Product	Quantity
GT20-15PCO	Protective cover for oil	1
GT20-12PCO
GT20-10PCO
GT20-08PCO
GT21-10WPCO	GOT2000 Series Protective Cover for Oil
GT21-07WPCO	for GT27/GT25/GT23/GT2107 User's Manual	1
GT25-05PCO	(This manual)
GT25-05PCO-2

Referenced Standard: GB/T15969.2 (Requirement of Chinese standardized law)

1. OVERVIEW

This user’s manual explains GOT 2000 series protective cover for oil (hereinafter referred to as the protective cover for oil).

Use of the protective cover for oil improves oil resistance and chemical resistance of the GOT. *1

*1: It is not the one to guarantee all customer's environments.

Moreover, it is not likely to be able to use it in the environment to which oil or the medicine splashes for a long time and the environment with which Oilmist is filled.

The following table shows the protective covers for oil and the screen sizes for the applicable GOT

Model	Screen sizes for the applicable GOTs
GT20-15PCO	15”
GT20-12PCO	12.1”
GT20-10PCO	10.4”
GT20-08PCO	8.4”
GT21-10WPCO	10.1” wide screen
GT21-07WPCO	7” wide screen
GT25-05PCO	5.7” (except GT2505)
GT25-05PCO-2	5.7” (GT2505)
GT25T-07WPCO	7” wide screen (rugged model)

2.SPECIFICATIONS

2.1Performance specifications

The performance specifications of the protective cover for oil are indicated below. The general specifications of the protective cover for oil are the same as those of the GOT.

For the general specifications of the GOT, refer to the GOT2000 Series User's Manual (Hardware).

Item	GT20-15PCO		GT20-12PCO			GT20-10PCO				GT20-08PCO
Level of					IP67F
	Caution: Oil or the medicine might not be able to splash for a long time,
protection
	and to use it in the environment with which Oilmist is filled.
Material		Cover: Nitrile rubber, Display: PET sheet
Weight	0.31(0.68)		0.21(0.46)			0.20(0.44)				0.16(0.35)
Item	GT21-10WPCO					GT21-07WPCO
Level of					IP67F
	Caution: Oil or the medicine might not be able to splash for a long time,
protection
	and to use it in the environment with which Oilmist is filled.
Material		Cover: Nitrile rubber, Display: PET sheet
Weight	0.14(0.30)					0.09(0.20)
Item	GT25-05PCO				GT25-05PCO-2			GT25T-07WPCO
Level of					IP67F
	Caution: Oil or the medicine might not be able to splash for a long time,
protection
	and to use it in the environment with which Oilmist is filled.
Material		Cover: Nitrile rubber, Display: PET sheet
Weight	0.09(0.20)				0.09(0.20)			0.15(0.33)
										Unit: kg(lb)

POINT

For installing the GOT with the protective cover for oil, the control panel thickness must be 1.6 to 3mm because of the cover thickness. (Control panel thickness without the cover: 1.6 to 4mm)

2.2 Oil resistance, chemical resistance

The protective cover for oil is made of materials with high oil and chemical resistance so that the cover can be used in various oil and chemical atmospheres. Because oils, including cutting oils, contain a small amount of additives depending on oil products, oil resistance of the cover cannot be stated.

Prior to use the cover, test the cover in operating environments, and then check the oil and chemical resistance of the cover.

Test contents and oil resistance of cover

The protective cover for oil is soaked in the following oils for 2000 hours, and then oil resistance of the cover is checked.

		Change in		Adhesion
Oil type	Product	appearanceand	between cover			Oil resistance
		dimension		and sheet
Water-insoluble	Grinding oil	No change		No change
cutting oil	(Yushiron oil CL35)
Water-soluble	Grinding oil
	(Noritake cool CG-	No change		No change
cutting oil
	50P)
3. EXTERNAL DIMENSIONS
		Protective
		cover for oil
H
						GOT
	W				D
Dimensions	GT20-15PCO	GT20-12PCO GT20-10PCO				GT20-08PCO
W	409	372		314		252
	(16.10)	(14.65)	(12.36)			(9.92)
H	314.5	261		233		209
	(12.38)	(10.28)		(9.96)		(9.18)
D	12.5	12		12		12
	(0.49)	(0.47)		(0.47)		(0.47)
Dimensions	GT21-10WPCO			GT21-07WPCO
W	263(10.35)				200(7.87)
H	205(8.07)				153(6.02)
D	12(0.47)				12(0.47)
Dimensions	GT25-05PCO	GT25-05PCO-2			GT25W-07WPCO
W	178(7.01)	175(6.89)				225(8.86)
H	154(6.06)	153.5(6.04)				169(6.65)
D	12(0.47)	12(0.47)				12(0.47)

Unit: mm (inch)

4. INSTALLATION AND REMOVAL PROCEDURE

POINT

For attaching the protective cover for oil to the GOT already mounted on the control panel, follow the procedures as below.

•Remove the GOT from the control panel.

Make sure to externally shut off all phases of the power supply and remove all cables from the GOT in advance.

•Clean dirt off surfaces of the GOT and control panel.

4.1 install the protective cover

For attaching the protective cover for oil, refer to the example of the GT2712.

1)Position the POWER LED frame of the cover to the POWER LED on the GOT front face, and the direction of the cover is decided

GOT

POWER LED

POWER LED Window

Protective cover for oil

2)One corner of the cover is pulled outside, and it hangs it on the corner of the front panel of GOT.

Please do not pull the oil cover more than the necessity, and do not bend it extremely. The seat part and the rubber part in the display part might flake off.

The corner is hung.

GOT

Protective cover for oil

3)From the place where the cover is hung, hang the corner of the cover sequentially and attach the entire edge of the cover to cover rubber packing parts in the back of the front panel of the GOT.

(It is the order of the arrow from A side to D side.)

The corner on the left is hung and the oil cover is hung from A side to D side on the starting point sequentially.

D

C

A

B

POINT

Please confirm all surroundings.

Whether the rubber packing part is surely covered to prevent going into such as the liquids in the board.

Make sure that corners of protective cover for oil match those of GOT front.

4)Mount the GOT onto the control panel.

When the control panel is dirty, clean the control panel.

The panel cutting dimensions and mounting screw tightening torque with the protective cover for oil are the same as those without the cover.

For mounting the GOT on the control panel, refer to the GOT2000 Series User's Manual (Hardware)

		GOT
	Protective	Panel cut dimensions
	cover for oil
		Mounting metal fixture
		Control panel

4.2 Removing the protective cover

Perform the reverse procedure to attaching the protective cover for oil.

5. PRECAUTIONS FOR USE

1)The protective cover for oil is a consumable product.

Check the cover for scratch, damage or dirt at regular intervals, and replace with new one if necessary.

2)Do not push the protective cover for oil with pointed tools, including mechanical pencils and screwdrivers.

Doing so causes scratches and damages of the cover.

3)Do not clean the protective cover for oil with bleaches, thinners, organic solvents, corrosive chemicals, and others.

Doing so causes changes in shape and color of the cover.

4)When the protective cover for oil is attached to the GOT, do not stretch and bend the cover too much.

Doing so may cause a separation between the sheet and rubber.

5)Do not place or use the protective cover for oil in direct sunshine.

When the protective cover for oil gets dusts, wipe the dusts off with a damp cloth.

6)When the protective cover00000 for oil is used, the USB connector on the GOT front face cannot be used.

7)When the protective cover for oil is used, the human sensor does not correctly operate.

Disable the human sensor with the utility.

For the human sensor setting, refer to the GOT2000 Series User's Manual (Hardware).

8)Do not attach and remove the protective cover for oil frequently. Doing so reduces oil resistance and chemical resistance.

9)It is not the one to guarantee all customer's environments.

Moreover, it is not likely to be able to use it in the environment to which oil splashes for a long time and the environment with which Oilmist is filled.

Warranty

Mitsubishi Electric will not be held liable for damage caused by factors found not to be the cause of Mitsubishi Electric; machine damage or lost profits caused by faults in the Mitsubishi Electric products; damage, secondary damage, accident compensation caused by special factors unpredictable by Mitsubishi Electric; damages to products other than Mitsubishi Electric products; and to other duties.

For safe use

•This product has been manufactured as a general-purpose part for general industries, and has not been designed or manufactured to be incorporated in a device or system used in purposes related to human life.

•Before using the product for special purposes such as nuclear power, electric power, aerospace, medicine or passenger movement vehicles, consult with Mitsubishi Electric.

•This product has been manufactured under strict quality control. However, when installing the product where major accidents or losses could occur if the product fails, install appropriate backup or failsafe functions in the system.

Country/Region		Sales office/Tel
USA		Mitsubishi Electric Automation, Inc.
		500 Corporate Woods Parkway, Vernon Hills, IL 60061, U.S.A.
		Tel: [phone]
Brazil		Mitsubishi Electric do Brasil Comercio e Servicos Ltda.
		Avenida Adelino Cardana, 293, 21 andar, Bethaville, Barueri SP,
		Brasil CEP 06401-147
		Tel: [phone]
Mexico		Mitsubishi Electric Automation, Inc. Mexico Branch
		Mariano Escobedo #69, Col. Zona Industrial, Tlalnepantla Edo. Mexico, C.P.54030
		Tel: [phone]
Germany		Mitsubishi Electric Europe B.V. German Branch
		Mitsubishi-Electric-Platz 1, 40882 Ratingen, Germany
		Tel: [phone]
UK		Mitsubishi Electric Europe B.V. UK Branch
		Travellers Lane, Hatfield, Hertfordshire, AL10 8XB, U.K.
		Tel: [phone]
Italy		Mitsubishi Electric Europe B.V. Italian Branch
		Centro Direzionale Colleoni - Palazzo Sirio, Viale Colleoni 7,
		Agrate Brianza (MB), Italy
		Tel: [phone]
Spain		Mitsubishi Electric Europe B.V. Spanish Branch
		Carretera de Rubi 76-80-Apdo.420, 08190 Sant Cugat del Valles (Barcelona), Spain
		Tel: [phone]
France		Mitsubishi Electric Europe B.V. French Branch
		25, Boulevard des Bouvets, 92741 Nanterre Cedex, France
		Tel: [phone]
Czech		Mitsubishi Electric Europe B.V. Czech Branch
		Avenir Business Park, Radlicka 751/113e, 158 00 Praha 5, Czech Republic
		Tel: [phone]
Turkey		Mitsubishi Electric Turkey A.S. Umraniye Branch
		Serifali Mahallesi Nutuk Sokak No:5, TR-34775 Umraniye / Istanbul, Turkey
		Tel: [phone]
Poland		Mitsubishi Electric Europe B.V. Polish Branch
		ul. Krakowska 50, 32-083 Balice, Poland
		Tel: [phone]
Russia		Mitsubishi Electric (Russia) LLC St. Petersburg Branch
		Piskarevsky pr. 2, bld 2, lit “Sch”, BC “Benua”, office 720;
		RU-195027 St. Petersburg, Russia
		Tel: [phone]
South Africa		Adroit Technologies
		20 Waterford Office Park, 189 Witkoppen Road, Fourways, Johannesburg, South Africa
		Tel: [phone]
China		Mitsubishi Electric Automation (China) Ltd.
		No.1386 Hongqiao Road, Mitsubishi Electric Automation Center, Shanghai, China
		Tel: [phone]
Taiwan		SETSUYO ENTERPRISE CO., LTD.
		6F, No.105, Wugong 3rd Road, Wugu District, New Taipei City 24889, Taiwan
		Tel: [phone]
Korea		Mitsubishi Electric Automation Korea Co., Ltd.
		7F-9F, Gangseo Hangang Xi-tower A, 401, Yangcheon-ro, Gangseo-Gu,
		Seoul 07528, Korea
		Tel: [phone]
Singapore		Mitsubishi Electric Asia Pte. Ltd.
		307 Alexandra Road, Mitsubishi Electric Building, Singapore 159943
		Tel: [phone]
Thailand		Mitsubishi Electric Factory Automation (Thailand) Co., Ltd.
		12th Floor, SV.City Building, Office Tower 1, No. 896/19 and 20 Rama 3 Road,
		Kwaeng Bangpongpang, Khet Yannawa, Bangkok 10120, Thailand
		Tel: [phone] to 31
Indonesia		PT. Mitsubishi Electric Indonesia
		Gedung Jaya 11th Floor, JL. MH. Thamrin No.12, Jakarta Pusat 10340, Indonesia
		Tel: [phone]
Vietnam		Mitsubishi Electric Vietnam Co., LTD. Ho Chi Minh Head Office
		Unit 01-04, 10th Floor, Vincom Center, 72 Le Thanh Ton Street, District 1,
		Ho Chi Minh City, Vietnam
		Tel: [phone]
India		Mitsubishi Electric India Pvt. Ltd. Pune Branch
		Emerald House, EL -3, J Block, M.I.D.C., Bhosari, Pune - 411026, Maharashtra, India
		Tel: [phone]
Australia		Mitsubishi Electric Australia Pty. Ltd.
		348 Victoria Road, P.O. Box 11, Rydalmere, N.S.W. 2116, Australia
		Tel: [phone]

HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN NAGOYA WORKS : 1-14, YADA-MINAMI 5-CHOME, HIGASHI-KU, NAGOYA, JAPAN

When exported from Japan, this manual does not require application to the Ministry of Economy, Trade and Industry for service transaction permission.

Specifications subject to change without notice. Printed in Japan, March 2019.