Livarno 103756-14-01-BS, 103756-14-02-BS User Manual
LED LIGHT STRIP
LED LIGHT STRIP
Operation and Safety Notes
IAN 103756
103756-14-01-BS
1 x
1
1 x
1
2
4 3
103756-14-02-BS
4
2 x
6
1 x
5
1 2
3
5 6
6 5
1 x
103756-14-01-BS
A
103756-14-02-BS
103756-14-02-BS
B C
1 x
7
410 mm
8
2 x
545 mm
9
2 x
50 mm
103756-14-02-BS
10
2 x
15 mm
11
53 mm
2 x
27 mm
12
9
9
D E
103756-14-02-BS103756-14-02-BS
LED LIGHT STRIP
Q
Proper use
The under-unit lights
103756-14-01-BS and
103756-14-02-BS are intended
for providing illumination and
for mounting on furniture.
Underunit light 103756-14-02-BS
can also be mounted on walls.
The product may only be used
indoors in dry rooms. The lamps
cannot be
be mounted
flammable surfaces. This device
is intended for use only in a
domestic, private household
environment.
Q
eplaced. The light can
on all normally
Description of
parts and features
103756-14-01-BS
1
Drill hole
2
LED
3
ON/OFF switch (“Touch
switch” )
4
Socket for connecting lead
5
Plug-in mains adapter with
connection lead (length
approx. 2 m)
6
Screw
103756-14-02-BS
1
ON/OFF switch
2
Socket for connecting lead
3
LED
4
Protective cap
5
Drill hole for wall mounting
6
Slot for mounting rail
7
Connecting lead with mains
plug
8
Extension lead
9
Mounting rail
10
Dowel
11
Screw for wall mounting
12
Screw for under cabinet
installation
Q
Technical data
103756-14-01-BS
Operating voltage:
Lamps:
LED:
Nominal power: max. 3 W
Protection
category:
Main adapter:
Rated voltage,
primary: 100–240V ~
Rated voltage,
secondary: 12V
Protection class:
Main adapter (model no.:
LPS03-120-0250-3) CE
standard tested.
103756-14-02-BS
Operating voltage:
Lamps:
LED:
Nominal power: max. 3 W
Protection
category:
Q
Safety
12 V
6 x power LED
6 x
0.5 W
50–60 Hz
250 mA
230–240 V ~
50 Hz
4 x power LED
4 x
0.5 W
Safety
advice
The right to claim under the
guarantee shall be rendered
invalid in respect of damage
caused by the non-observance
of these operating instructions!
No liability is
consequent damage!
liability is accepted for
to property or persons caused
by improper handling or nonobservance of the safety
advice!
accepted for
No
damage
J This appliance can be used
by children aged from 8
years and above and
persons with reduced
physical, sensory or mental
capabilities or lack of
experience and knowledge
if they have been given
supervision or instruction
concerning use of the
appliance in a safe way
and understand the hazards
involved. Children shall not
play with the appliance.
Cleaning and user
maintenance shall not be
made by children without
supervision.
J Do not allow the lamp or
the packaging materials to
lie around unattended.
Plastic film or bags,
Styrofoam etc. can turn into
dangerous toys for children.
J
Do not operate the lamp in
J Do not expose the lamp to
J Do not attach the light to
LED cannot be replaced.
CAUTION!
DANGER OF
EXPLOSION!
potentially explosive
environments in which there
are inflammable vapours,
gases or dusts.
direct sunlight, rain, snow or
ice. Failure to observe this
advice may result in
damage to the product.
damp or conductive
substrates.
To avoid danger
to life from
electric shock
GB/IE GB/IEGB/IEGB/IE
J Never use your lamp if you
discover that it is damaged
in any way.
J In the event of damage,
repairs or other problems
with the lamp, please
contact the Service Centre
or an electrician.
J Before installation, switch
off the electrical circuit at
the circuit breaker box or
remove the fuse from the
fuse box.
J Never let the lamp come
into contact with water or
other liquids.
J Never open or insert
anything into electrical
fittings or equipment. Doing
this sort of thing can lead to
a serious danger to life from
electric shock.
J Before assembly, ensure
that the mains voltage
available corresponds to
the operating voltage
necessary of the light
(103756-14-01-BS: 100 - 240 V ∼;
103756-14-02-BS: 230 - 240 V ∼) .
J Use Model 103756-14-01-BS
only with the supplied
plug-in mains adapter.
Failure to comply with this
instruction will invalidate
any warranty claims.
To avoid danger
of fire and injury
J RISK OF INJURY! Check
every bulb and lampshade
for damage immediately
upon unpacking. Do not fit
the light if the bulbs and / or
lampshades are faulty. If
they are, contact the service
point for a replacement.
DANGER
OF ELECTRIC SHOCK!
DANGER OF DAMAGE
TO PROPERTY!
DANGER OF INJURY!
Ensure that you do not strike
electrical cables, gas or
water pipes when you are
drilling into the wall. If
necessary, check the wall
using a suitable detector
before you drill.
J
RISK OF
INJURY FROM
BURNS! Ensure
the lamp has been switched
off and allowed to cool
before
you touch it. In this
way you
danger of burns.
will avoid the
Bulbs give
off a lot of heat around the
top of the lamp.
J Do not use this light for
dimmers or electronic
switches. It is not suitable
for these purposes.
Working safely
J Install the lamp so that it is
protected from moisture,
wind and dirt.
J Make careful preparations
for the assembly and take
sufficient time. Clearly lay
out all components and any
additional tools or materials
that might be required so
that they are readily to
hand.
J Remain alert at all times
and always watch what you
are doing. Always proceed
with caution and do not
assemble the lamp if you
cannot concentrate or feel
unwell.
Q
Installation and
operation
Q
Installing light
103756-14-01-BS
j Measure the space for
installation of the light. Use
a spirit level to position it
correctly.
j Mark the position of the drill
1
holes
in the under
cabinet light.
j Mark the two mounting
holes at a distance of
362 mm apart.
j Drill the holes, ø approx.
2 mm, depth approx.
10 mm.
j Position the under cabinet
light according to the drilled
holes and tighten the
6
screws
.
j Plug the connecting lead
5
into the socket 4.
j Plug the mains plug of the
connecting lead
5
into a
socket. Your under cabinet
light is now ready for
operation.
Note: Only use the lamp
with the mains adapter it
was delivered with
(LPS03-120-0250-3).
Damage due to use of a
different adapter is not
covered by the guarantee.
Q
Installing light
103756-14-02-BS
j Use the mounting rails 9
(see also Fig. B) and the
12
screws
installation.
j Measure the space for
installation of the light. Use
a spirit level to position it
correctly.
for under cabinet
Mark where you wish to
drill and pre-drill the holes.
j Mark the distance of
533 mm for the two fixing
holes. Drill the holes: ø
approx. 2 mm, approx.
10 mm deep.
Note: The supplied screws
are for standard installation
under wall cabinets and are
not suitable for every type
of wall. If installing on
concrete walls, for example,
you will need to use special
dowels and screws.
Information on suitable
installation material can be
obtained from specialist
stores.
j First screw only one of the
mounting rails
9
in the predrilled positions with the
supplied screws
12
.
j Place the under cabinet
light flat on the mounting
surface and push it onto the
mounting rail
stop in the slot
9
up to the
6
(see Fig. C).
j Push the second mounting
9
rail
into the slot 6 on
the under cabinet light so
that the drilled hole is
visible. Tighten the screw in
this position (see Fig. D).
j Now push the under
cabinet light a little to the
right. Both mounting rails
9
should now be firmly
positioned (see Fig. E).
Check that the under
cabinet light is fitted
securely.
j Plug the connecting lead
7
into the socket 2.
j Plug the mains plug of the
connecting lead
7
into a
socket. Your under cabinet
light is now ready for
operation.
Q
Mounting model
103756-14-02-BS
on a wall
j Measure up the wall or
mounting surface for drilling
the holes. Use a spirit level
to improve accuracy.
j Mark the two mounting
holes a distance of approx.
432 mm apart.
j Now drill the mounting
holes (ø approx. 6 mm,
depth approx. 30 mm).
CAUTION! Make sure that
you do not damage any
electrical cables during this
operation.
j Insert the supplied dowels
10
into the drilled holes.
Insert the supplied screws
11
into the dowels and
tighten them. Let them
project a distance of about
1.3 mm from the wall or
mounting surface.
j Attach the light to the
11
screws
appropriate wall mounting
holes
j Plug the connection cable
with mains plug
socket for the connection
cable
j Plug the connection cable
with mains plug
mains socket. Your light is
now ready for operation.
Extensions
j Note: Ensure that no more
than 3 under-unit lights of the
same type (103756-14-02-BS)
are connected together in
series. Install each
additional light at a
using the
5
.
2
.
7
into the
7
into the
distance of approx. 15 cm
as described.
j Remove the protective cap
4
by unscrewing the
screw. Connect the two
under-unit lights to the
2
socket
extension lead
using the
8
. Then
you only need one connection lead
7
for the power
supply.
j CAUTION! First ensure
that all the under-unit lights
are connected by an
extension lead
8
before
you insert the mains lead
into the mains socket.
Q
Maintenance and
Cleaning
Allow the lamp to cool down
completely.
DANGER
TO LIFE FROM
SHOCK! Before carrying
out any tasks on the lamp,
switch off the electrical
circuit at the circuit breaker
box or remove the fuse from
the fuse box.
j CAUTION! Do not use
solvents, petrol etc.
TO LIFE FROM
SHOCK! For reasons of
electrical safety, the light
must never be cleaned with
water or other fluids or be
immersed in water. When
cleaning, only use a dry,
lint-free cloth.
Q
Disposal
The packaging and
ancillary packing
consist entirely of
ELECTRIC
DANGER
ELECTRIC
environmentally-friendly
materials. They can be disposed
of at your local recycling facility.
The symbol of the
wheelie bin with the
line through it means
that, in the European Union, the
product has to be disposed of in
a separate refuse collection.
This applies to the product and
to all components bearing this
symbol. Products marked in this
way may not be disposed of
along with normal domestic
waste but have to be handed in
at a recycling collection point
for electrical and electronic
appliances. Recycling
helps to reduce the consumption
of raw materials and to ease the
burden on the environment.
Q
Warranty
The device has been
manufactured to strict quality
guidelines and meticulously
examined before delivery. In the
event of product defects you
have legal rights against the
retailer of this product. Your
legal rights are not limited in
any way by our warranty
detailed below.
The warranty for this device is 3
years from the date of purchase.
Should this device show any
fault in materials or manufacture
within three years from the date
of purchase, we will repair or
replace it - at our choice - free
of charge to you.
The warranty period begins on
the date of purchase. Please
keep the original sales receipt in
a safe location. This document is
required as your proof of
purchase. This warranty
becomes void if the device has
been damaged or improperly
used or maintained.
The warranty applies to faults in
material or manufacture. This
warranty does not cover
product parts subject to normal
wear, thus possibly considered
consumables (e.g. batteries) or
for damage to fragile parts, e.g.
switches, rechargeable batteries
or glass parts.
GB/IEGB/IEGB/IEGB/IEGB/IEGB/IEGB/IE
IAN 103756
OWIM GmbH & Co. KG
Stiftsbergstraße 1
D-74167 Neckarsulm
Model no.: 103756-14-01-BS /
103756-14-02-BS
Version: 10 / 2014
6
Loading...