Livarno 1225-022L, 1252-022L User Manual [en, de, cs]

0 (0)

LED  FLOOR LAMP

LED  FLOOR LAMP

LED  STOJACÍ LAMPA

Operation  and Safety Notes

Pokyny 

pro obsluhu a bezpečnostní pokyny

LED  STOJACA LAMPA

LED -STEHLEUCHTE

Pokyny  pre obsluhu a bezpečnostné pokyny

Bedienungs - und Sicherheitshinweise

IAN 65147

Before  reading, unfold the page containing the illustrations and familiarise yourself with all functions of the device.

Před  čtením si otevřete stranu s obrázky a potom se seznamte se všemi funkcemi přístroje.

Pred  čítaním si odklopte stranu s obrázkami a potom sa oboznámte so všetkými funkciami prístroja.

Klappen  Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen Funktionen  des Gerätes vertraut.

GB

Operation and Safety Notes

Page

5

CZ

Pokyny pro obsluhu a bezpečnostní pokyny

Strana

8

SK

Pokyny pre obsluhu a bezpečnostné pokyny

Strana

11

DE / AT / CH

Bedienungsund Sicherheitshinweise

Seite

15

Livarno 1225-022L, 1252-022L User Manual

 

10

1

1225-022L

 

2

 

 

 

 

3

 

 

4

5a

 

5

 

 

 

 

6

5b

 

 

 

7

1

 

 

 

 

2

1252-022L

10

3

 

 

 

9

 

 

8

 

5a

 

 

 

 

4

5b

 

5

 

 

6

 

7

 

 

 

 

 

 

 

Introduction / Safety

 

LED Floor Lamp

 

Lower stand tube section

 

5b

 

 

 

 

6

Mains plug

 

 

Introduction

7

Stand

 

 

8

Counterweight (model 1252-022L)

 

 

 

 

 

Locking lever (model 1252-022L)

 

 

 

 

9

 

 

Congratulations on your new product.

 

Lamp arm

 

 

 

10

 

 

 

 

 

 

You have selected a high quality product.

 

 

 

 

 

Please be sure to carefully read the com-

 

Technical Data

 

 

 

 

plete operating instructions. Fold out the page with

 

 

the illustrations. These instructions are part of the

 

 

 

 

product and contain important information on setup

Model no.:

1225-022L or 1252-022L

 

and handling. Always follow all safety instructions.

Operating voltage:

230 V 50 Hz

 

Before using this product for the first time verify the

Illuminant:

2 LED modules, each

 

correct voltage and that all parts are properly in-

 

 

approx. 5 Watts (LEDs not

 

stalled. Should you have any questions or you are

 

 

replaceable)

 

unsure about operating the product, please contact

Base:

ø 26.0 cm

 

the dealer or service centre. Please keep these in-

Total height, arm 90°:

approx. 1.25 m

 

structions in a safe place and pass them on third

Protection class:

II / 

 

parties as applicable.

 

 

 

Intended use

This light is only suitable for indoor use in dry and enclosed spaces. This product is intended for private household use only.

Scope of delivery

Check immediately after unpacking that the parts are complete and that the product is in proper condition.

1 Floor lamp, model 1225-022L or 1252-022L 1 Base

1 Adjustment lever

1 Counterweight (model 1252-022L)

1 Instructions for use

Parts description

1ON / OFF switch

2Reflector

3Adjustment lever

4Retaining sleeve

5Stand tube

5a Upper stand tube section

Safety

Safety information

Damage due to failure to comply with these operating instructions will invalidate the guarantee! We assume no liability for consequential damage! We assume no liability for material damage or personal injury due to improper handling or failure to comply with the safety instructions!

Avoid the risk of fatal injury from electric shock

Check the light for damage every time before you use it. Never use the light if it shows any signs of damage.

CAUTION! A damaged light means danger of death from electric shock. In the event of damage, repairs or other problems with the light please contact the service centre or a qualified electrician.

To prevent hazards, a damaged flexible outer lead on this lamp must be replaced by the manufacturer, its service representative or an equally qualified professional!

GB 5

Safety / Start-up

Before use, verify the available mains voltage corresponds with the operating voltage of the lamp (230 V ).

Ensure that the light does not come into contact with water or other liquids under any circumstances.

Always unplug from the mains before assembling, disassembling, cleaning, or if the lamp will not be used for extended periods.

Never open any of the components of the electrical equipment or insert any objects into the same components. This will pose a risk of fatal injury from electric shock.

The illuminant is not replaceable.

This light is not suitable for dimmer or electronic switches.

Prevent fire and injury hazards

RISK OF INJURY! Check every illuminant for damage immediately upon unpacking. Do not install the light if the illuminants are defective.

In this case contact the service centre for a replacement.

Do not look directly into the light source (light bulb, LED etc.).

Do not leave the light or packaging material lying unattended. Plastic film or bags, plastic parts etc. can turn into dangerous toys for children.

Do not cover the lamp or the mains plug with objects. Excessive heat can result in a fire. Never leave the lamp unattended whilst in use.

Safe working

Mount the light so that it is protected from moisture and dirt.

Carefully prepare for assembly and allow yourself adequate time. Organise all parts and any necessary additional tools or materials before starting so they are easy to reach.

Always be attentive! Always pay attention to what you are doing and use common sense. Never assemble the lamp if you are unfocused or feel unwell.

6 GB

Start-up

Mounting the light

Note: When assembling the stand tube 5 be sure not to damage the mains lead inside the lamp.

Unfold the floor lamp.

Insert the upper stand tube section 5a into the lower stand tube section 5b.

Carefully pull the mains lead out of the stand tube 5 .

Tighten the retaining sleeve 4 to secure the stand tube 5 .

Screw the lower stand tube section 5b clockwise into the base 7 .

Model 1252-022L: Tighten the counterweight 8 at the end of the lamp arm 10 .

Screw the adjustment lever 3 onto the reflector 2 .

Plug the mains plug 6 into a properly installed socket.

Your light is now ready to use.

Adjusting the height

Loosen the retaining sleeve 4 .

Adjust the floor lamp to the desired height. Tighten the retaining sleeve 4 .

Note: Retighten the retaining sleeve 4 if it loosens and the lamp adjusts in height.

Switching the lamp on / off

Switch the lamp on or off using the ON / OFF switch 1 on the reflector 2 .

Adjusting the reflector

Note: Only adjust the reflector 2 with the light switched off.

Note: Retighten the locking lever 9 if the lamp arm 10 on model 1252-022L changes in position.

Start-up / Maintenance and Cleaning / Disposal / Information

Allow the lamp to cool off completely.

Turn the lamp arm 10 to the desired position. Turn the reflector 2 to the desired angle.

Maintenance and Cleaning

DANGER OF ELECTRIC SHOCK! First unplug the mains plug 6 from the socket.

CAUTION! DANGER OF BURN INJURIES!

Allow the lamp to cool down completely.

DANGER OF ELECTRIC SHOCK! For electrical safety, never clean the light with water or other liquids, or immerse it in water.

Do not use solvents, benzene or similar substances. They could damage the light. Only use a dry, lint-free cloth for cleaning.

Disposal

The package and packaging materials consist entirely of environmentally friendly materials. They can be disposed of at your local recycling facility.

The symbol of the wheelie bin with the

line through it means that, in the European Union, the product has to be disposed

of in a separate refuse collection. This applies to the product and to all components bearing this symbol. Do not dispose of products bearing this symbol in your normal household waste, but instead they must be taken for recycling to a collection site for electrical and electronic appliances. Recycling helps to reduce the consumption of raw materials and protects the environment.

Information

Warranty

been carefully produced under strict quality control. Within the warranty period we shall rectify without charge all material and manufacturing defects. In the event of a defect arising during the warranty period, please send the appliance to the listed Service Centre address, making reference to the following article number: 1225-022L / 1252-022L.

Wear parts (such as bulbs) and damage caused by improper handling, non-observance of the operating instructions or unauthorised interference are excluded from the warranty. The performance of services under the warranty does not extend or renew the warranty period.

Manufacturer / Service

Briloner Leuchten GmbH Im Kissen 2,

59929 Brilon, Germany

Tel.: +49 (0) 29 61 / 97 12–0 Fax: +49 (0) 29 61 / 97 12–199 E-mail: Info@briloner.de www.briloner.de

IAN 65147

Please have your receipt and the article number (e.g. IAN 12345) ready as your proof of purchase when enquiring about your product.

Declaration of conformity

This product fulfils the requirements of the applicable European and national directives (Electromagnetic Compatibility 2004 / 108 / EC, Low Voltage Directive 2006 / 95 / EC, Ecodesign Directive 2009 / 125/EC, RoHS Directive 2011 / 65 / EU). Conformity has been demonstrated. The relevant declarations and documents are held by the manufacturer.

You receive a 36 month warranty on this product, valid from the date of purchase. The appliance has

GB 7

Loading...
+ 14 hidden pages