Linear DRG - LV Owner's Manual

DRG-LV			DESCRIPTION		The DRG has a “F” connector for attaching an antenna. The				STEP 1 Open receiver case. To open case,
			The DRG-LV	is a digital receiver designed for use with	receiver is supplied with a 9-inch local antenna, a three foot				squeeze sides of case and rotate upward.
DRG-2LV			automatic gate operators or systems where a remote antenna		75 ohm coaxial cable, and a bulkhead			connector for
					mounting the antenna outside the gate operator enclosure.
			is needed. The DRG-2LV will operate two gates, one gate and
			an obstacle sensor or channel one can open the gate and
			channel two can close the gate.		RECEIVER
			All of the Delta-3 transmitters, including the two and
								3-FOOT
DIGITAL			four-channel transmitters, are compatible with the the DRG.					CABLE
			The Delta-3 radio format provides 256 different digital codes.
GATE			The codes are set using the 8-position coding switches in the					CASE SCREWS
RECEIVER			units. In order to avoid the possibility of duplicating codes in
			adjacent systems, factory set codes should not be used.
Installation Instructions			The receivers can operate from 10.2-16 VDC or 12-16 VAC
			and are normally powered from the gate operator. The relay					MOUNTING
			contact(s) are rated at 5 amps @ 30 volts AC/DC NEC Class					HARDWARE
			2 circuit.
						LOCAL		NUT
						ANTENNA	BULKHEAD	WASHER	SQUEEZE BOTH SIDES AT TABS
							CONNECTOR		AND TILT UPWARD
[phone] ∙ www.linearcorp.com
STEP 2A	DRG-LV code setting. To set a		STEP 2B	DRG-2LV code setting. Select any	STEP 3	Transmitter code setting. Locate			STEP 4 Connect receiver relay output.
code, select any valid combination of ON and			valid combination of ON and OFF positions for		the coding switch on the transmitter and set the				Connect the appropriate channel wires (Ch. 1 -
OFF positions for the switch keys numbered 1- 8.			each of the switch keys numbered 1 - 8. Use a		eight keys identical to those on the desired				two gray wires), (Ch. 2 - two yellow wires) to the
Use a paper clip to set the eight keys.			different code combination than that used for		channel of the receiver. Be sure they match				appropriate activation terminals on the gate
			channel one switch.		exactly. I f	u s i n g a t w o	o r f o u r - c h a n n e l		operator.
SET CODE					transmitter, refer to the coding instructions
					included with the transmitter for proper system					GATE OPERATOR
SWITCH KEYS			SET CHANNEL TWO		coding.				DRG		MANUAL ACCESS
			CODE SWITCH KEYS						Digital Gate Receiver		REQUEST
CHANNEL ONE
SWITCH KEYS			CHANNEL TWO		REMOVE BATTERY
					ACCESS DOOR					1	COMMON
			SWITCH KEYS
							SWITCHES IN		CHANNEL	2	RELAY
							TRANSMITTER		ONE
									GRAY
										3 12 V RADIO POWER
THIS SWITCH			THIS SWITCH
HAS 2, 3 & 6 ON										OBSTACLE INPUT
			HAS 2, 4 & 6 ON			CODING
DO NOT USE:						SWITCH			YELLOW	1	COMMON
								THIS SWITCH
			DO NOT USE:						CHANNEL
ALL ON; ALL OFF;									TWO
			ALL ON; ALL OFF;					HAS 2, 3 & 6 ON		2	OBSTACLE
ALT ON/OFF, OR OFF/ON
			ALT ON/OFF, OR OFF/ON
STEP 5	C o n n e c t r e c e i v e r t o p o w e r .		STEP 6	Mounting the receiver. U s e t h e	STEP 7	Connect antenna. C o n n e c t t h e			LINEAR LIMITED WARRANTY
Connect the red power input wire to the 12V radio			screws provided to mount the receiver within the		coaxial cable to the “F” connector on the receiver.				This product is warranted to the consumer against defects in material and workmanship
									for one year from the date of purchase. This warranty applies to first retail buyers of
power and the black wire to the common terminal			operator housing. This provides protection from		Drill a 3/8" hole on the top of the operator housing				new devices. Warrantor will repair, or at its option, replace, any device it finds that
									requires service under this warranty, and will return the repaired or replaced device to
on the gate operator. Alternately connect wires to			the elements. Secure case with case screws.		for the bulkhead connector. Insert the connector				the consumer at the warrantor’s cost. For warranty service and shipping instructions
a 12-16 VAC transformer.					and secure it with the nut and lock washer.				contact warrantor at the address shown below. Devices must be sent to warrantor for
									service at owner’s expense. The remedies provided by this warranty are exclusive.
					Connect the cable and antenna to the operator.				Implied warranties under state law are to the one year period of this written warranty.
									Some states do not allow limitations on how long an implied warranty lasts, so the above
									limitation may not apply to you. In order to be protected by this warranty, save your
	GATE OPERATOR								proof of purchase and send copy with equipment should repair be required. This
									warranty gives you specific legal rights, and you may also have other rights which vary
									from state to state.
		MANUAL		MOUNT RECEIVER			SLIDE WEATHER		All products returned for warranty service require a Return Product Authorization Number
									(RPA#). Contact Linear Technical Services at 1-800-421-1587 for an RPA# and other
		ACCESS REQUEST					RESISTANT CAP
				INSIDE GATE					important details.
DRG					CONNECT COAXIAL		OVER CONNECTION
									IMPORTANT !!!
				HOUSING
Digital Gate Receiver					CABLE TO "F"
		OBSTACLE							Linear radio controls provide a reliable communications link and fill an important need
					CONNECTOR
	BLACK						INSERT BULKHEAD		in portable wireless signaling. However, there are some limitations which must be
									observed.
	1	COMMON					CONNECTOR THROUGH		For U.S. installations only: The radios are required to comply with FCC Rules and
							OPERATOR HOUSING		Regulations as Part 15 devices. As such, they have limited transmitter power and
	2	RELAY							therefore limited range.
	RED								A receiver cannot respond to more than one transmitted signal at a time and may be
		12 V RADIO POWER							blocked by radio signals that occur on or near their operating frequencies, regardless of
	3			SECURE CASE			SECURE CONNECTOR		code settings.
				CLOSED WITH TWO			TO HOUSING USING		Changes or modifications to the device may void FCC compliance.
				SCREWS AT BOTTOM			WASHER AND NUT		Infrequently used radio links should be tested regularly to protect against undetected
									interference or fault.
	INPUT VOLTAGE REQUIREMENT			OF CASE
							CONNECT CABLE TO		A general knowledge of radio and its vagaries should be gained prior to acting as a
	10.2-16 VOLT DC or 12-16 VAC
							BULKHEAD CONNECTOR		wholesale distributor or dealer, and these facts should be communicated to the ultimate
									users.
									Copyright © 1999 Linear Corporation		216267 B