Linear MTR3, MTR1 User Manual

				DESCRIPTION				1	Refer to the instructions provided with the garage door opener to set it
		MTR1	The Linear PRO Access digital transmitter is a wireless radio control designed						into “learn” mode.
			for use with automatic garage and gate operators.						• Press the opener’s LEARN BUTTON for 1 second and release.
			Each of the transmitter buttons will send a unique code when pressed. One						• The opener should BEEP and the LIGHT should BLINK once.
	PRO ACCESSTM	MTR3							• The RED LED will remain lit in Learn Mode for 15 seconds.
			button can be used to activate the individual’s garage door opener, a second
									While the RED LED is lit, PRESS and HOLD the transmitter’s START/
	1 and 3 Button Transmitter		button can operate an access gate, a third button can activate an additional					2
			garage door operator.						STOP key until the opener BEEPS and the light BLINKS once.
	Operation Instructions		Linear PRO Access transmitters and receivers do not contain a typical “coding						PREPARING TO ADD OR REMOVE A REMOTE
			switch”. Each transmitter is permanently coded at the factory. The receiver is
									1 PRESS THE	2 PRESS THE DESIRED
			programmed by “learning” a transmitter’s unique digital code. The receiver will
									LEARN BUTTON	REMOTE BUTTON
			activate only from the “memorized” transmitters.							WHILE RED LED IS ON
			The transmitter is powered by a Type CR2032 “coin-cell” battery. They should						THE RED LED
			last at least 1 year with normal use. The indicator light on the transmitter will						WILL GLOW FOR
									15 SECONDS
			glow when the unit is activated. If the indicator lights dimly, or not at all when					After programming, test the transmitter
			transmitting, the battery needs to be replaced. To conserve battery life, an							BE SURE THE DOOR OR
								from various locations. Be sure the		GATE AREA IS CLEAR!
			internal timer limits the transmission duration to 20 seconds if a transmitter					door or gate areas are clear. Activate
			button is held down.
	GTO Access Systems, LLC							the transmitter and verify that the
	[phone] • [phone]							remote triggers the operator(s).
	www.gtoaccess.com
		VISOR CLIP INSTALLATION							LIMITED WARRANTY
	The visor clip can be installed for horizontal or vertical mounting. Slide the visor clip into one of the slots shown.					This product is warranted to the consumer against defects in material and workmanship for one year from the date of purchase.
						This warranty applies to first retail buyers of new devices. Warrantor will repair, or at its option, replace, any device it finds that
						requires service under this warranty, and will return the repaired or replaced device to the consumer at the warrantor’s cost. For
						warranty service and shipping instructions contact warrantor at the address shown below. Devices must be sent to warrantor
						for service at owner’s expense. The remedies provided by this warranty are exclusive. Implied warranties under state law are to
						the one year period of this written warranty. Some states do not allow limitations on how long an implied warranty lasts, so the
						above limitation may not apply to you. In order to be protected by this warranty, save your proof of purchase and send copy with
						equipment should repair be required. This warranty gives you specific legal rights, and you may also have other rights which
						vary from state to state.
		REPLACING THE BATTERY				All products returned for warranty service require a Return Product Authorization Number (RPA#). Contact Linear Technical
						Service at 1-800-543-1236 for an RPA# and other important details.
	When the indicator light on the remote glows dimly, or fails to light at all when								IMPORTANT !!!
	the remote is activated, the battery needs replacing.		1	2	3	Linear PRO Access radio controls provide a reliable communications link and fill an important need in portable wireless signaling.
	Follow the steps in the diagram and use caution to keep batteries away from					However, there are some limitations which must be observed.
						• For U.S. installations only: The radios are required to comply with FCC Rules and Regulations as Part 15 devices. As such, they
	children.
							have limited transmitter power and therefore limited range.
	Replace old battery with a fresh CR2032 Lithium battery.					•	A receiver cannot respond to more than one transmitted signal at a time and may be blocked by radio signals that occur on or
							near their operating frequencies, regardless of code settings.
	Properly dispose of old batteries. Many electronic stores and supermarkets					•	Changes or modifications to the device may void FCC compliance.
			4	5	6	•	Infrequently used radio links should be tested regularly to protect against undetected interference or fault.
	have battery recycling bins.
						• A general knowledge of radio and its vagaries should be gained prior to acting as a wholesale distributor or dealer, and these
	Never dispose of batteries in fire because they could explode.						facts should be communicated to the ultimate users.
						WARNING: Changes, modifications or adjustments not expressly approved by GTO Access Systems, LLC could void the user’s
	WARNING					authority to operate this equipment. There Are No User Serviceable Parts.
						NOTICE: This device complies with part 15 of the FCC rules and with Industry Canada license-exempt RSS standard(s).
						Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept
	KEEP BATTERIES OUT REACH OF CHILDREN. Swallowing batteries can lead to serious injury or death.					any interference, including interference that may cause undesired operation of the device.
	If you suspect someone has swallowed a battery, go to the hospital immediately. Do not induce					Le présent appareil est conforme aux CNR d’Industrie Canada applicables aux appareils radio exempts de licence. L’exploitation
	vomiting or eat or drink anything.					est autorisée aux deux conditions suivantes : (1) l’appareil ne doit pas produire de brouillage, et (2) l’utilisateur de l’appareil doit
	For more information, call the National Battery Ingestion Hotline: [phone].					accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.
	The battery identification number for this product is CR2032.
						Copyright © 2016 GTO Access Systems, LLC				Document Number: 10014570 REV A