LG SPJ9B-W, SJ9 User Manual

OWNER’S MANUAL

SJ9

SMART Hi-Fi

AUDIO

Wireless Multi-room Sound Bar

Please read this manual carefully before operating your set and retain it for future reference. To view the instructions of advanced features, visit http://www.lg.com and then download Owner’s Manual. Some of the content in this manual may differ from your unit.

MODEL

SJ9 (SJ9, SPJ9B-W)

www.lg.com

Copyright © 2017 LG Electronics Inc. All Rights Reserved.

1

Started Getting

2 Getting Started

	Safety Information			product identification and supply ratings, please refer
				NOTICE: For safety marking information including
				to the main label on the bottom or the other surface
				of the product.
		CAUTION
		RISK OF ELECTRIC SHOCK		CAUTION concerning the Power Cord
		DO NOT OPEN
				The Power Plug is the disconnecting device.In case
	CAUTION: TO REDUCE THE RISK OF ELECTRIC
				of an emergency, the Power Plug must remain readily
	SHOCK DO NOT REMOVE COVER (OR BACK)
				accessible.
	NO USER-SERVICEABLE PARTS INSIDE REFER
				Check the specification page of this owner’s manual
	SERVICING TO QUALIFIED SERVICE PERSONNEL.
				to be certain of the current requirements.

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous

voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and

maintenance (servicing) instructions in the literature accompanying the product.

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

WARNING: Do not install this equipment in a confined space such as a book case or similar unit.

CAUTION: Do not use high voltage products around this product. (ex. Electrical swatter)This product may malfunction due to electrical shock.

CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus.

CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings shall be never be blocked by placing the product on a bed, sofa, rug or other similar surface.This product shall not be placed in a builtin installation such as a bookcase or rack unless

proper ventilation is provided or the manufacturer’s instruction has been adhered to.

Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your device, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the device, and have the cord replaced with an exact replacement part by an authorized service center. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the device.

CAUTION: No naked flame sources, such as lighted candles, should be placed on the apparatus.

Getting Started	3

This device is equipped with a portable battery or	Symbols
accumulator.

Safety way to remove the battery from the equipment: Remove the old battery or battery pack, follow the steps in reverse order than the assembly. To prevent contamination of the environment and bring on possible threat to human and animal health, the old battery or the battery put it in the appropriate container at designated collection points. Do not dispose of batteries or battery together with other waste.It is recommended that you use local, free reimbursement systems batteries and accumulators. The battery should not be exposed to excessive heat such as sunshine, fire or the like.

~Refers to alternating current (AC).

0	Refers to direct current (DC).
	Refers to class II equipment.
1	Refers to stand-by.

!Refers to “ON” (power).

Refers to dangerous voltage.

1

Started Getting

4 Table of Contents

Table of Contents		31	Connecting the speakers to your Home
			Network (Additional)
		31	–  Connecting the additional speaker to your
			network with a LAN cable
1	Getting Started	33	–  Connecting the additional speaker to your
			network via the Wi-Fi Setup Method
2	Safety Information	35	Using the Bridge
6	Main Features	35	–  Use as a root device (wired to the home
6	Introduction		router)
7	Remote control	37	–  Use as a wireless extender
8	Front panel	38	Using Media Server for PC
8	Rear panel	38	–  Music Flow PC Software for windows
9	Installing the sound bar
9	Mounting the main unit on a wall	3	Operating
2	Connecting	40	Enjoying the Music with Music Flow Player app
		40	–  Overview of Home menu
11	Organizing cables	41	–  Overview of the side menu
11	Wireless subwoofer connection	42	–  Playing a song
12	Connecting to your TV	43	–  Overview of Playback
12	–  Using an OPTICAL cable	45	Different ways of listening to music
13	–  LG Sound Sync	45	–  Group Playback
14	–  Using an HDMI cable	46	–  Surround Sound Mode (Home Cinema
15	–  ARC (Audio Return Channel) function		Mode)
15	–  What is SIMPLINK?	48	–  Seamless playback
16	–  Additional information for HDMI	49	Setting the Speaker with Music Flow Player
17	Optional equipment connection		app
17	–  DOLBY ATMOS®	49	–  Overview of setting menu
18	–  HDMI connection	49	–  [General] Menu
18	–  OPTICAL IN connection	50	–  [Speakers] Menu
19	–  PORTABLE IN connection	51	–  [Alarms/Sleep Timer] Menu
20	Initial Multi-Room Setup	51	–  [Account management] Menu
20	–  Wired connection (Music Flow Mesh	51	–  [Time Zone] Menu
	Network Connection)	52	–  [Advanced Settings] Menu
20	–  Wireless connection (Standard Wireless	54	–  [Chromecast] Menu
	Connection)	54	–  [Version Info.] Menu
20	Installing “Music Flow Player” App	54	–  [Open source licenses] Menu
21	–  Starting with Music Flow Player app	55	Using a BLUETOOTH Wireless Technology
22	Connecting the speaker to your Home	55	–  About BLUETOOTH
	Network	55	–  BLUETOOTH profiles
22	–  Simple Connection (EZ Setup)	55	–  Listening to Music of a BLUETOOTH Device
23	–  Connecting the speaker to your network	57	–  BLUETOOTH connection lock (BT LOCK)
	with a LAN cable	57	Other operations
25	–  Connecting the speaker to your Network	57	–  Using your TV remote control
	via the Wi-Fi Setup Method (Android)	57	–  AV Sync
28	–  Connecting the speaker to your Network	58	–  Turn off the sound temporarily
	via the Wi-Fi Setup Method (iOS)	58	–  Sleep timer setting

58 –  Auto display Dimmer

58–  Displaying input source information

58–  Auto power down

58–  AUTO POWER On/Off

59–  Auto function change

60Sound adjustment

60–  Adjust volume level automatically

60–  Adjust the Treble/Bass/Subwoofer

60–  Night mode

61Standby mode

61 –  Standby mode

61 –  Network standby mode

61 –  BLUETOOTH standby mode

61 Reset the Speaker

61 –  Resetting the speaker

4 Troubleshooting

62Troubleshooting

62–  General

63–  Network

64–  Application and PC Software

64–  NOTES to use wireless

65–  NOTES to release Demo mode

5 Appendix

66 File requirement

66Trademarks and licenses

67Specifications

69 Handling the Speaker

69Important Information Relating to Network Services

70TERMS OF USE

Table of Contents

5

1

2

3

4

5

Some of the content in this manual may differ from Music Flow Player app depending on the application’s version.

1

Started Getting

6 Getting Started

Main Features

Made for iPod/iPhone/iPad or Android device

Enjoys music from iPod/iPhone/iPad or Android device with simple connection.

LG Sound Sync

Controls volume level of this unit by the remote control of your LGTV that is compatible with LG Sound Sync.

Introduction

Symbol used in this manual

,,Note

Indicates special notes and operating features.

>>Caution

Indicates cautions for preventing possible damages from abuse.

Music Flow Player application

Listens to music stored on your smart device.

You can control this speaker with your iPod touch/ iPhone/iPad or Android device via Music Flow Player app.This speaker and your smart device must be connected to the same network. Visit Apple “App Store” or Google “Play Store” or use the QR code shown below to search for “Music Flow Player” app. For detailed information, refer to page 20.

(Android OS)

(Apple iOS)

yy Depending on the application’s version and the settings of smart device, Music Flow Player app may not be operated normally.

yy Some smart devices may not be compatible with this speaker.

BLUETOOTH®

Listens to music stored on your Bluetooth device.

Getting Started	7

Remote control			• • • • • • • • • • • • • •A•
			1(Power) : Switches the unit ON or OFF.
			F : Selects the function and the input source.
			Input source / Function Display

Replacement of Battery

Remove the battery cover on the rear of the remote control, and insert the battery with 4and 5 matched correctly.

Wi-Fi	WI-FI
Optical
ARC	OPT/HDMI ARC
LG Sound Sync (Wired)
Bluetooth	BT
LG Sound Sync (Wireless)	LG TV
HDMI IN	HDMI IN
Portable	PORTABLE

SOUND EFFECT : Selects a sound effect mode. (Mute) : Mutes the sound.

: Set Night mode to On to reduce the sound intensity and improve fineness and softness.

: Adjusts sound level ofTreble, Bass and Subwoofer. (Page 60)

VOL o/p: Adjusts speaker volume.

• • • • • • • • • • • • • •B•

C/V(Skip) : Skips Fast backward or Forward. dM(Play/Pause) : Starts playback. / Pauses playback.

INFO :

-Displays the input source information.

-Displays the connected Bluetooth device name on

Bluetooth function.

REPEAT : Listen to your music repeatedly.

AUTO VOL : Turns on or off the AUTO VOLUME mode.

AV SYNC :

-Synchronizes the audio and video.

-ControlsTV remote. (Page 57)

SLEEP : Sets the system to turn off automatically at a specified time.

AUTO POWER :

-Turns on or off AUTO POWER function. (Page 58)

-Turns on or off the Bluetooth connection lock. (Page 57)

1

Started Getting

8 Getting Started

Front panel

1

Started Getting

ALED indicator	DThe buttons are located on the rear.
Shows connection status.
BRemote sensor
CDisplay window

Rear panel

A1(Standby)

F (Function): Selects the function and input source. (WI-FI, OPT/HDMI ARC, BT, LGTV,

HDMI IN, PORTABLE)

-/+ (Volume)

(Wi-Fi): Connects initial Music Flow product to your network wirelessly.

(Add): Adds the additional Music Flow

BUSB (Service only) : S/W download connector

CLAN port

DPORTABLE IN connector EOPTICAL IN connector

FHDMI OUT (TV ARC) : Connect to HDMIIN (ARC) onTV.

GHDMI IN

product to your network.

(In case that one or more Music Flow product is connected.)

Getting Started	9

Installing the sound bar

You can hear the sound by connecting the unit to the other device :TV, Blu-ray disc player, DVD player, etc.

Place the unit in front of theTV and connect it to the device you want. (Refer to pp. 12 - 33)

You can place the wireless subwoofer anywhere in your room. But it is better to place the subwoofer near the main unit.Turn it slightly toward the center of the room to reduce the wall reflections.

Mounting the main unit on a wall

1

You can mount the main unit on a wall.

Started Getting

>>Caution

yy For best performance of wireless connection such as Bluetooth or wireless subwoofer, do not install the unit on Metallic furniture because wireless connection communicates through a module positioned on the bottom of the unit.

yy Be careful not to make scratches on the surface of the Unit /Subwoofer when installing or moving them.

,,Note

For the convenient button usage, it is recommended to take some distance between the soundbar and yourTV when you install the sound bar.

>>Caution

Because it is difficult to make a connection after installing this unit, you should connect the cables before installation.

Preparation materials

Unit

Wall bracket install guide Wall bracket

Screws

(Not supplied)

Screws (A)

Wall plug

10 Getting Started

1. Match theTV’s BOTTOM EDGE of Wall bracket	5. Put the unit on the brackets to match screw
install guide with the bottom ofTV and attach to	holes on the bottom of the unit.
the position.

1

Started Getting

2.When you mount it on a wall (concrete), use the wall plugs. You should drill some holes. A guide sheet (Wall bracket install guide) is supplied to drill. Use the sheet to check the point to drill.

6. Fix the unit with the screws firmly.

3.Remove the Wall bracket install guide.

4.Fix the brackets with screws (A) as shown in the illustration below.

,,Note

,,Note

To detach the unit, perform it in reverse order.

>>Caution

yy Do not install this unit upside down.It can damage the parts of this unit or be the cause of personal injury.

yy Do not hang onto the installed unit and avoid any impact to the unit.

yy Secure the unit firmly to the wall so that it does not fall off.If the unit falls off, it may result in an injury or damage to the product.

yy When the unit is installed on a wall, please make sure that a child does not pull any of connecting cables, as it may cause it to fall.

Screws (A) and Wall Plugs are not supplied for mounting the unit. We recommend the Hilti (HUD-1 6 x 30) for the mounting.

Getting Started 11

Organizing cables

You can organize the cable with cable ties.

1.Hold the cables together with cable ties as shown below.

2.Tighten cable ties.

Wireless subwoofer connection

LED indicator of wireless subwoofer

LED Color	Status
Green	The connection is trying.
(Blink)
Green	The connection is completed.
Red	The wireless subwoofer is in
	standby mode or the connection
	is failed.
Off (No	The power cord of wireless
display)	subwoofer is disconnected.

Setting up the wireless subwoofer for the first time

1.Connect the power cord of the sound bar and the wireless subwoofer to the outlet.

2.Turn on the sound bar.The sound bar and the wireless subwoofer will be automatically connected.

Manually pairing wireless subwoofer

When your connection is not completed, you can check red LED on the wireless subwoofer and the wireless subwoofer does not make sound.To solve the problem, follow the steps below.

1.Press Pairing button on the rear of the wireless subwoofer.

-- The green LED on the front of the wireless subwoofer blinks quickly.

2. Turn on the sound bar.

1

Started Getting

3. Pairing is completed.

-- The green LED on the front of the wireless subwoofer turns on.

2

Connecting

12 Connecting

,,Note

yy It takes a few seconds (and may take longer) for the main unit and the subwoofer to communicate with each other and make sounds.

yy The closer the main unit and the subwoofer, the better sound quality.It is recommended to install the main unit and the subwoofer as close as possible and avoid the cases below.

-- There is an obstacle between the main unit and the subwoofer.

-- There is a device using same frequency with this wireless connection such as a medical equipment, a microwave or a wireless LAN device.

-- Keep the sound bar and the subwoofer away from the device (ex. wireless router, microwave oven, etc.) over 1 m to prevent wireless interference.

> 1 m

Connecting to your TV

Please connect with this unit andTV using the optical digital cable or HDMI cable considering the state of the TV.

Using an OPTICAL cable

1.Connect the OPTICALIN jack on the back of the unit to OPTICAL OUT jack on theTV using an

OPTICAL cable.

Optical cable

2.Select the input source to OPT/HDMI ARC by pressing F button on the remote or unit repeatedly.

You can see “OPTICAL” on the display window if connecting normally between this unit and your

TV.

,,Note

yy Before connecting the optical cable, be sure to remove the protection plug cover if your cable has the cover.

yy You can enjoy theTV audio through the speakers of this unit.In the case of someTV models, you must select the external speaker option from theTV menu. (For details, reference yourTV user manual.)

yy Set up the sound output of TV to listen to the sound through this unit :

TV setting menu [[Sound] [[TV Sound output] [[External speaker (Optical)]

yy Details of TV setting menu vary depending on the manufacturers or models of yourTV.

yy If this unit is connected by OPTICAL and ARC at the same time, the ARC signal is a high priority.

Connecting 13

LG Sound Sync

With wired connection

You can control some functions of this unit by yourTV’s remote control with LG Sound Sync.It is compatible with the LGTV that is supported LG

Sound Sync. Make sure of the LG Sound Sync logo on yourTV.

Controllable function by LGTV’s remote control : Volume up/down, mute

Refer to theTV’s instruction manual for the details of LG Sound Sync.

Make one of the following connections, depending on the capabilities of your equipment.

,,Note

yy You can also use the remote control of this unit while using LG Sound Sync.If you useTV's remote control again, the unit synchronizes with theTV.

yy When the connection fails, make sure of the condition of theTV and power.

yy Make sure of the condition of this unit and the connection in the cases below when using LG Sound Sync.

-- The unit is turned off.

-- Changing the function to the others. -- Disconnecting the optical cable.

yy The amount of time to turn off this unit is different depending on yourTV when you set AUTO POWER function to ON.

1.Connect your LGTV to the unit by using an optical cable.

Optical cable

2.Set up the sound output ofTV to listen to the sound through this unit :

TV setting menu [[Sound] [[TV Sound output] [[LG Sound Sync (Optical)]

3.Turn on the unit by pressing 1on the remote control or 1on the unit.

4.Select OPT/HDMI ARC function by using F on the remote control or F on the unit until the function is selected.

You can see “LG OPT” on the display window if connecting normally between this unit and your

TV.

,,Note

Details ofTV setting menu vary depending on the manufacturers or models of yourTV.

2

Connecting

2

Connecting

14 Connecting

With wireless connection

1.Turn on the unit by pressing 1on the remote control or 1on the unit.

2.Select LGTV function by using F on the remote control or F on the unit until the function is selected.

3.Set up LG Sound Sync (Wireless) on theTV. Refer to theTV’s instruction manual.

“PAIRED” appears on the display window for about 3 seconds and then you can see “LGTV” on the display window if connecting normally between this unit and yourTV.

,,Note

yy If you turned off the unit directly by pressing 1(Power), LG Sound Sync (Wireless) will be disconnected.

yy If yourTV and this unit are connected through LG Sound Sync (Wireless), this unit will be Network standby mode regardless of the status of network connection when this unit is turned off. Check dimmed white LED on the unit.

Using an HDMI cable

If you connect this unit to aTV that supports HDMI CEC and ARC (Audio Return Channel), you can enjoy theTV audio through the speakers of this unit without connecting the optical cable.

1.Connect the HDMI OUT (TV ARC) jack on the back of the unit to ARC jack on theTV using an

HDMI cable.

HDMI cable

2.Select the input source to OPT/HDMI ARC by pressing F button on the remote or unit repeatedly.

You can see “ARC” on the display window if connecting normally between this unit and your

TV.

,,Note

yy You can enjoy theTV audio through the speakers of this unit.In the case of someTV models, you must select the external speaker option from theTV menu. (For details, reference yourTV user manual.)

yy Set up the sound output of TV to listen to the sound through this unit :

TV setting menu [[Sound] [[TV Sound output] [[External speaker (HDMI ARC)]

yy Details of TV setting menu vary depending on the manufacturers or models of yourTV.

yy Depending on your LGTV model, you may need to turn on the SIMPLINK function on your LGTV.

yy When you return to ARC function from another function, you need to select the input source to OPT/HDMI ARC.Then this unit changes to ARC function automatically.

Connecting 15

ARC (Audio Return Channel) function

The ARC function enables an HDMI capableTV to send the audio stream to HDMI OUT of the unit.

To use this function :

-- YourTV must support the HDMI-CEC and ARC function and the HDMI-CEC and ARC must be set to On.

-- The setting method of HDMI-CEC and ARC may differ depending on theTV. For details about ARC function, refer to yourTV manual.

-- You must use the HDMI cable (Type A, High Speed HDMI™ cable with Ethernet).

-- You must connect the HDMI OUT on the unit with HDMIIN of theTV that supports ARC function using an HDMI cable.

-- You can connect only one Sound bar toTV compatible with ARC.

What is SIMPLINK?

Some functions of this unit are controlled by the TV’s remote control when this unit and LGTV’s with SIMPLINK are connected through HDMI connection.

Controllable functions by LGTV’s remote control : Power on/off, volume up/down, etc.

Refer to theTV owner’s manual for the details of SIMPLINK function.

LGTV’s with SIMPLINK function has the logo as shown above.

,,Note

yy Depending on the state of the unit, some SIMPLINK operation may differ from your purpose or not work.

yy Depending on aTV or a player which is connected with this unit, SIMPLINK operation may differ from your purpose.

2

Connecting

2

Connecting

16 Connecting

Additional information for HDMI

yy When you connect an HDMI or DVI compatible device make sure of the following:

-Try switching off the HDMI/DVI device and this player. Next, switch on the HDMI/DVI device and leave it for around 30 seconds, then switch on this player.

-The connected device’s video input is set correctly for this unit.

-The connected device is compatible with

720 x 576p (or 480p), 1280 x 720p,

1920 x 1080i, 1920 x 1080p, 4096 x 2160p or 3080 x 2160p video input.

yy Not all HDCP-compatible HDMI or DVI devices will work with this player.

-The picture will not be displayed properly with non-HDCP device.

,,Note

yy If a connected HDMI device does not accept the audio output of the player, the HDMI device’s audio sound may be distorted or may not output.

yy Changing the resolution when the connection has already been established may result in malfunctions.To solve the problem, turn off the player and then turn it on again.

yy When the HDMI connection with HDCP is not verified,TV screen is changed to black screen. In this case, check the HDMI connection, or disconnect the HDMI cable.

yy If there are noises or lines on the screen, please check the HDMI cable (length is generally limited to 4.5 m(15 ft).

yy You cannot change the video resolution in the HDMIIN mode. Change the video resolution of the connected component.

yy If the video output signal is abnormal when your personal computer is connected to HDMI IN jack, change the resolution of your personal computer to 576p (or 480p), 720p, 1080i or 1080p.

HDMI cable Checklist

Some HDMI cables have poor signal transmission, which can cause problems with sound and video transmission.

Even after HDMI cable connections, if no sound, sound interrupted, noise occurring from the sound bar and/or no video, no smooth video on yourTV, the HDMI cable may be the problem.

Use the cable marked with the premium HDMI certification logo. Also make sure that the your using cable is a certifiedType A, Ethernet high-speed

HDMI™ cable.

STANDARD HDMI CABLE WITH ETHERNET	(X)
HIGH SPEED HDMI CABLE	(X)
HIGH SPEED HDMI CABLE WITH ETHERNET	(O)

Connection through HDMI Cable*

Your television must support the newest HDMI features (HDMI CEC1) / ARC (Audio Return Channel)) to fully enjoy the Live broadcasting channel with audio system through an HDMI cable. Unless your TV supports these HDMI features, the audio system should be connected through an OPTICAL cable.

1) HDMI CEC (High-Definition MultimediaInterface Consumer Electronics Control)

Consumer Electronics Control (CEC) is an HDMI feature designed to allow the user to command and control the CEC-enabled devices, that are connected through HDMI by using only one of their remote controls.

* Trade names for CEC are SimpLink (LG) , Anynet+ (Samsung), BRAVIA Sync (Sony), EasyLink (Philips), etc.

Connecting 17

Optional equipment connection

DOLBY ATMOS®

What is DOLBY ATMOS®?

Dolby Atmos gives you amazing experience you’ve never before by overhead sound, and all the richness, clarity, and power of Dolby sound.

For using DOLBY ATMOS®

yy DOLBY ATMOS® is available only in HDMIIN and ARC mode.

-- To use DOLBY ATMOS® in ARC mode, yourTV has to support DOLBY ATMOS®.

yy It is needed to set up an audio output on external devices (Blu-ray disc player,TV etc.) to “No incoding” such as “Bitstream”, “Auto” or “Bypass”.

-- If you can select audio output sampling rate, set it to 192 kHz.

1.Connect HDMIIN jack on the back of the unit to HDMI OUT jack on the external device such as Blu-ray disc player, DVD player, etc.

2.Connect HDMI OUT (TV ARC) jack on the back of the unit to HDMIIN jack on theTV.

3.Set the input source to HDMIIN or OPT/HDMI ARC. Press repeatedly F on the remote control or F on the unit until the function is selected.

-- If you select HDMIIN, you can hear the sound from the external device. Select it when playing the external device.

-- If you select OPT/HDMI ARC, you can hear the sound from yourTV. Select it when watching the TV.

You can see “DOLBY ATMOS”on the display window if connecting normally between this sound bar and yourTV and DOLBY ATMOS contents is played.

,,Note

yy DOLBY ATMOS® supports 5.1.2 channel.

yy This unit supports 4K passthrough. When you play a disc which has a 4K video signal, this unit delivers the signal to yourTV.

yy If the sound bar does not sound or the video onTV is not smooth, the HDMI cable may be the problem. Refer to the HDMI cable checklist. (Page 16)

2

Connecting

2

Connecting

18 Connecting

HDMI connection

You can enjoy the sound from the external device which is connected to HDMIIN jack on this unit.

To the Blu-ray disc player,

DVD player, etc.

1.Connect HDMIIN jack on the back of the unit to HDMI OUT jack on the audio device such as Bluray disc player, DVD player, etc.

2.Set the input source to HDMIIN. Press repeatedly F on the remote control or F on the unit until the function is selected.

OPTICAL IN connection

Connect an optical output jack of external devices to the OPTICALIN jack.

Optical cable

To the optical output jack of external device

1.Connect the OPTICALIN jack on the back of the unit to optical out jack of your external device.

2.Select the input source to OPT/HDMI ARC by pressing F button on the remote or unit repeatedly.

You can see “OPTICAL” on the display window if connecting normally between this unit and your device.

,,Note

Before connecting the optical cable, be sure to remove the protection plug cover if your cable has the cover.

Connecting 19

PORTABLE IN connection

Optional equipment connection

You can enjoy both sound and picture from the

external device you connect.

Listening to music from your portable player

The unit can be used to play the music from many types of portable players or external devices.

1.Connect the portable player to the PORTABLEIN connector of the unit.

2.Turn the power on by pressing 1(Power).

3.Select the PORTABLE function by pressing F on the remote control or F on the unit until the function is selected.

4.Turn on the portable player or external device and start playing it.

2

Connecting

OR

1.Connect HDMIIN jack of yourTV to HDMI OUT jack on the external device such as Blu-ray disc player, DVD player, etc.

2.Connect the OPTICALIN jack on the back of the unit to OPTICAL OUT jack on theTV using an

OPTICAL cable.

Or connect the HDMI OUT (TV ARC) jack on the back of the unit to HDMIIN (ARC) jack on theTV using an HDMI cable.

3.Set the input source to OPT/HDMI ARC. Press repeatedly F on the remote control or F on the unit until the function is selected.

,,Note

If the sound bar does not sound or the video onTV is not smooth, the HDMI cable may be the problem. Refer to the HDMI cable checklist.

(Page 16)

2

Connecting

20 Connecting

Initial Multi-Room Setup

When installing the Music Flow product for the first time, you can choose two types of connection as below.

Wired connection (Music Flow Mesh Network Connection)

Connect your speaker to the home router using LAN cable.

Then you can connect the additional Music Flow products (Optional) to your home network wirelessly. Refer to “Connecting the speakers to your Home Network (Additional)” on page 31.

LAN Cable

Wireless connection (Standard Wireless Connection)

When the wired connection is unavailable between your speaker and home router, this unit offers music streaming service within home router’s Wi-Fi coverage.

Connect one of the your speaker to the home router wirelessly.

Then you can connect the additional Music Flow products (Optional) to your home network wirelessly. Refer to “Connecting the speakers to your Home Network (Additional)” on page 31.

Wireless signal

Installing “Music Flow

Player” App

Through Apple “App Store” or Google “Play Store”

1.Tap the Apple “App Store” icon or Google “Play Store” icon.

2.Type in “Music Flow Player” in the search bar and tap “Search”.

3.Select “Music Flow Player” in the search result list to download.

,,Note

yy Music Flow Player app will be available in version of the software as follow; Android OS : Ver 4.0 (ICS) (or later) iOS O/S : Ver 6.0 (or later)

yy Depending on the device, “Music Flow Player” app may not work.

Through QR code

Install “Music Flow Player” app through QR code. Scan the QR code using the scanning application.

(Android OS)

(Apple iOS)

Connecting 21

,,Note

yy Make sure that your smart device is connected to the internet.

yy Make sure that your smart device has a scanning application.If you don’t have, download it from Apple “App Store” icon or Google “Play Store”.

Starting with Music Flow Player app

When you launch Music Flow Player app for the first time, the terms of use and Chromecast Service appear on the screen.

1.Check the contents of terms of use and select [Accept].

3.Select [Connect product] to install the speaker you’ve purchased.

Refer to “Connecting the speaker to your Home Network” on page 22.

,,Note

If you want to return to the terms of use screen, initialize the Music Flow Player app on the smart device’s setting menu.

2.Check the contents of Chromecast Service and select [Accept].

2

Connecting

2

Connecting

22 Connecting

Connecting the speaker to your Home Network

Using a wired network provides the best performance, because the attached devices connect directly to the network without radio frequency interference.

Please refer to the documentation for your network device for further instructions.

Preparation

yy Make sure that wireless network environment using a router is installed at your home.

yy Make sure that the speaker and the smart device are connected to the same router.

Requirements

yy Wireless router

yy Smart device (Android or iOS)

,,Note

yy Make sure that DHCP’s server is activated on wireless router.

yy If you cannot connect the speaker with your router, go to setting of the router and then make sure that “Allow wireless client to see each other and access my local network” box is unchecked.

Simple Connection (EZ Setup)

Preparation

yy For Simple Connection, Wi-Fi network condition is needed.

yy Make sure that the Bluetooth setting on your smart device in on.

yy Select WI-FI function by using F on the remote control or F on the sound bar.

,,Note

yy Simple Connection is supported by Bluetooth Ver 4.0 (or higher).

yy If Simple Connection screen is not displayed on the screen, connect the unit by the other way. Please refer to “Connecting the speaker to your network with a LAN cable” (page 23) or “Connecting the speaker to your Network via the Wi-Fi Setup Method” (page 25 or page 28)

1. Plug in the desired device, and tap [Next].

2.App searches for the speaker and connects it automatically,Tap [Next].

or