LG T1107TEFT0 Instruction manual

Washing Machine

OWNER'S MANUAL

MODELS : T1107TEFT0

Please read this manual carefully before operating your set. Retain it for future reference.

Record model name and serial number of the set.

Quote this information to your dealer when you require service.

P/No.: MFL62207707

4

<![if ! IE]>

<![endif]>Introduction

Safety Information

Read carefully and thoroughly through this booklet as it contains important safety information that will protect the user from unexpected dangers and prevent potential damages to the product.

This booklet is divided into 2 parts : Warning and Caution.

:This is a warning sign specifying user’s applications which might be dangerous.

:This is a sign specifying ‘Strictly Forbidden’ applications.

WARNING : Failure to comply with the instructions under this sign may result in major physical injuries or death.

CAUTION : Failure to comply with the instructions under this sign may result in minor physical injuries or damages to the product.

	WATER	WARNING
	HEATER
	SAFETY

•Under certain conditions hydrogen gas may be produced in a water heater that has not been used for two weeks or more. Hydrogen gas can be explosive under these circumstances.

If the HOT water has not been used for two weeks or more, prevent the possibility of damage or injury by turning on all Hot water faucets and allowing them to run for several minutes. Do this before using any electrical appliance which is connected to the HOT water system. This simple procedure will allow any built-up hydrogen gas to escape. Since the gas is flammable, do not smoke or use an open flame or appliance during this process.

	PROPER	CAUTION
	INSTALLATION

•The base opening must not be obstructed by carpeting when the washing machine is installed on a carpeted floor.

•Install or store where it will not be exposed to temperatures below freezing or exposed to the weather.

If the product is exposed to such conditions, electric shock, fire, break down or deformation may occur.

•Properly ground washer to conform with all governing codes and ordinances. Follow details in Installation Instructions.

If not grounded properly, break down and leakage of electricity may occur, which may cause electric shock.

•Must be positioned so that the plug is accessible.

If the plug is placed between the wall and the machine, it may get damaged, possibly causing fire or electric shock.

•Make sure the plug is completely pushed into the outlet.

Failure to do so may cause electric shock and fire due to overheating.

Safety Information

	YOUR	WARNING
	LAUNDRY
	AREA	• Keep the area underneath and around your appliances free of combustible
		materials such as lint, paper, rags, chemical, etc.

Operating with such materials around the machine may trigger explosion or fire.

•Close supervision is necessary if this appliance is used by or near children. Do not allow children to play on, with, or inside this or any other appliance.

There is potential danger that children might drown in the tub.

Do not touch the power plug with a wet hand.

It will cause electric shock

Do not put your hand, foot or anything under the washing machine while the washing machine is in operation.

There is a rotating mechanism under the machine, so you could be injured.

	WHEN USING	CAUTION
	THE WASHER

•Use this appliance only for its intended purpose as described in this Owner’s Manual.

•The laundry process can reduce the flame retardancy of fabrics. To avoid such a result, carefully follow the garment manufacturer’s wash and care instructions.

•To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect the washer at the household distribution panel by removing the fuse or switching off the cirduit breaker before attempting any maintenance or cleaning.

NOTE : Pressing Power button to turn off does NOT disconnect the appliance from the power supply.

•Make sure that drainage is working properly.

If water is not drained properly, your floor may get flooded. Flooded floors may induce electricity leakage, further resulting in electric shock or fire.

•If, during spinning, opening the lid does not stop the tub within about 15 seconds, immediately discontinue operating the machine.

Call for repair. A machine that spins with its door open may cause injuries.

Never reach into washer while it is moving.

Wait until the machine has completely stopped before opening the lid.

Even slow rotation can cause injury.

Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug.

Operating with a damaged plug may cause electric shock.

Do not use water hotter than 50°C.

Use of excessively hot water may cause damage to fabrics or cause leakage of water.

5

<![if ! IE]>

<![endif]>Introduction

6

<![if ! IE]>

<![endif]>Introduction

Safety Information

	WHEN USING	WARNING
	THE WASHER

Do not use a plug socket and wiring equipment for more than their rated capacity.

Exceeding the limit may lead to electric shock, fire , break down, and/or deformation of parts.

Do not mix chlorine bleach with ammonia or acids such as vinegar and/or rust remover.

Mixing different chemicals can produce toxic gases which may cause death.

Do not wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with combustible or explosive substances (such as wax, oil, paint, gasoline, drycleaning solvents, kerosene, etc). Do not add these substances to the wash water.

Do not use or place these substances around your washer or dryer during operation.

		It may ignite or explode.
	WHEN NOT	CAUTION
	IN USE

•Turn off water faucets to relieve pressure on hoses and valves and to minimize leakage if a break or rupture should occur. Check the condition of the fill hoses; they may need replacement after 5years.

•When the air temperature is high and the water temperature is low, condensation may occur and thus wet the floor.

•Wipe off dirt or dust on the contacts of the power plug.

Using unclean power plug may cause fire.

•Before discarding a washer, or removing it from service, remove the washer lid to prevent children from hiding inside.

Children may be trapped and suffocated if the lid is left intact.

Do not attempt to repair or replace any part of this appliance unless specifically recommended in this Owner’s Manual, or in published user-repair instructions that you understand and have the skills to carry out.

Operating the machine with improperly replaced parts may be a cause for fire or electric shock.

Do not tamper with controls.

It may lead to electric shock, fire , break down, deformation.

Do not yank the power cord in an attempt to disconnect the power plug. Securely hold the power plug to unplug the machine.

Failure to observe these instructions may cause electric shock or fire due to short-circuit .

When you are cleaning the washing machine, do not apply water directly to any part of the washing machine.

It will cause short circuit and electric shock.

Identification of Parts

Body

POWDER AND LIQUID

DETERGENT BOX

LINT FILTER

Clean regularly to stop linting on the clothes load.

BLEACH

DISPENSER

FUNCTION

SELECTOR

TUB

START/PAUSE

BUTTON

Use to start or stop the washing machine temporarily.

ADJUSTABLE LEGS

Use to level the washing machine for correct balance & spin operation.

WATER SUPPLY HOSE

Make sure the water does not leak.

POWER PLUG

If the supply cord is

damaged, it must be

replaced by the

manufacturer or its

service agents or

similarly qualified

person in order to avoid a hazard.

DRAIN HOSE for pump model

Check if the drain hose is hung up before operating the washing machine.

DRAIN HOSE

for non pump model

BASE

Accessories

Water supply hoses Drain hose Anti-rat cover (option)

or

or

1 Each for COLD and HOT water

NOTE

7

<![if ! IE]>

<![endif]>Introduction

“ ” Part can be different according to the model.

8

<![if ! IE]>

<![endif]>Introduction

Function Information

Our machine provides various washing methods which suits various conditions and types of laundry.

Different types of laundry washing

FUZZY(Normal) Wash

Use this Program for everyday washing e.g. sheets, towels, T-shirts. (refer to page 16)

JEANS Wash

Use this Program for heavily soiled durable garments e.g. overalls, jeans.

Thick and heavy clothes or those which are excessively dirty like jeans or working uniforms can be washed. (refer to page 16)

EXTRA CLEANING

Use this program to get better rising performance. (refer to page 16)

WOOL Wash

Wool clothes (lingerie, wool, etc.) which may be easily damaged can be washed. (refer to page 16)

The fibers of machine washable woolens have been specifically modified to prevent felting when they are machine washed. Most handknitted garments are not made of machine washable wool and we recommend that you hand wash them

•Before washing your woolens check the care label for the washing instructions.

•When washing woolens use a mild Detergent recommended for washing wool.

•Hand washed woolens may be spun in a washing machine to reduce the time they take to dry.

•To dry woolens lay down them flat on a towel and pat into shape. Dry woolens out of direct sunlight.

(The heat and tumble action of a dryer may cause shrinkage or felting of woolen garments.)

Some wool underlays and sheepskin products can be washed in a washing machine but may cause pump blockages. (Ensure that the whole article is suitable for machine washing and not just the backing material.)

You may wish to handwash these articles and place them in the machine to spin dry.

FAVORITE Wash

This setting allows you to store your FAVORITE wash conditions in the normal cycle memory. (refer to page 19)

SILENT Wash

Use this program to wash quietly at night. (refer to page 20)

Washing according to the condition of laundry

QUICK WASH

QUICK WASH can be selected to wash lightly soiled clothes of less than 2.0 kg in a short time. (refer to page 16)

SOAK Wash

SOAK Wash can be selected to wash heavily soiled laundry by soaking in water for some time to remove dirt and grime. (refer to page 18)

Other washing method

TUB CLEAN

Use this program to clean the inside of washing machine especially Inner tub & Outer tub . (refer to page 21)

DELAY START Wash

DELAY START Wash is used to delay the finishing time of the operation.

The number of hours to be delayed can be set by the user accordingly. (refer to page 24)

OPTION WASH

When the user needs only SPIN, RINSE/SPIN, RINSE, WASH/RINSE, WASH, WASH/RINSE/SPIN, SOAK/WASH/RINSE/SPIN. (refer to page 23)

Preparation Before Washing

Care Labels

* Look for a care label on your clothes. This will tell you about the fabric content of your garment and how it should be washed.

Sort clothes into loads that can be washed with the same wash cycle, Water Temperature and spin speed.

Sorting

To get the best results, different fabrics need to be washed in different ways.

• SOIL (Heavy, Normal, Light)	Separate clothes according to the type and amount of soil.
• COLOR (Whites, Lights, Darks)	Separate white fabrics from colored fabrics.
• LINT (Lint producers, Collectors)	Separate lint producers and lint collectors.
Lint Producers	Terry cloth, Chenille, Towels, Nappies, Diapers
Lint Collectors	Synthetics, Corduroy, Permanent Press, Socks

Check before Loading

• Check all pockets to make sure that they are empty. Things such as nails, hairclips, matches,
pens, coins, and keys can damage both your washer and your clothes.
• Mend any torn garments or loose buttons. Tears or holes may become larger during washing.
• Remove belts, underwires, etc. to prevent damage to the machine or your clothes.
• Pretreat any dirt and stains.
• Make sure the clothes are washable in water.	WIRE

•Check the washing instructions.

•Remove tissue in pockets.

Pretreatment on stains or heavy soil

•Pretreat shirt collars and cuffs with a pre-wash product or liquid Detergent when placing them in the washer. Before washing treat special stains with bar soaps, liquid Detergent or a paste of water and granular Detergent.

•Use a pretreat soil and stain remover.

Treat stains AS SOON AS POSSIBLE. The longer they are left the harder they are to remove.

(For more detail refer to page13)

Loading

Do not wash fabrics containing flammable materials (waxes, cleaning fluids, etc.).

Load Size

The WATER LEVEL should just cover the clothes. Adjust the load size accordingly. Loosely load clothes no higher than the top row of holes in the washer tub. To add items after washer has started, press Start button and submerge additional items. Close the lid and press Start button again to restart.

Light and Large-sized clothing

WARNING

Fire Hazard

Never place items in the washer that are dampened with gasoline or other flammable fluids.

No washer can completely remove oil.

Do not dry anything that has ever had any type of oil on it (including cooking oils).

Doing so can result in death, explosion, or fire.

Clothes like downs and woollens are light weight, large and float easily. Use a nylon net and wash them in a small amount of water. If the laundry floats during the wash cycle, it may become damaged. Use dissolved Detergent to prevent the Detergent from clumping.

Long laundry items

Use nylon nets for long, DELICATE items. For laundry with long strings or long length , a net will prevent tangling during washing. Fasten zippers, hook, and strings to make sure that these items don't snag on other clothes.

Nylon net is not supplied by LG.

9

<![if ! IE]>

<![endif]>hasW to gStartin eforeB

Special Guide for Stain Removal

WARNING

■Do not use or mix liquid chlorine bleach with other household chemicals such as toilet cleaners, rust removers, acid or products containing ammonia. These mixtures can produce dangerous fumes which can cause serious injury or death.

■To reduce the risk of fire or serious injury to persons or property, comply with the basic warnings listed below:

• Read and comply with all instructions on stain removal products.

•Keep stain removal products in their original labeled containers and out of children’s reach.

•Thoroughly wash any utensil used.

•Do not combine stain removal products, especially ammonia and chlorine bleach. Dangerous fumes may result.

•Never wash items which have been previously cleaned in, washed in, soaked in or spotted with gasoline, dry cleaning solvents or other flammable or explosive substances because they give off vapors that could ignite or explode.

•Never use highly flammable solvents, such as gasoline, inside the home. Vapors can explode on contact with flames or sparks.

13

<![if ! IE]>

<![endif]>hasW to gStartin eforeB

For successful stain removal:

•Remove stains promptly.

•Determine the kind of stain, then follow the recommended treatment in the stain removal chart below.

•To pretreat stains, use a prewash product, liquid Detergent, or a paste made from granular Detergent and water.

•Use COLD water on unknown stains because HOT water can set stains.

•Check care label instructions for treatments to avoid on specific fabrics.

•Check for colorfastness by testing stain remover on an inside seam.

•Rinse and wash items after stain removal.

Follow fabric care label instructions

		Stain Removal
	STAIN	TREATMENT
	Adhesive tape, chewing gum,	Apply ice. Scrape off excess. Place stain face down on paper towels. Saturate with prewash stain remover or
	rubber cement	nonflammable dry cleaning fluid.
	Baby formula, dairy products, egg	Use product containing enzymes to pretreat or soak stains.
	Beverages (coffee, tea, soda, juice,	Pretreat stain. Wash using COLD water and bleach safe for fabric.
	alcoholic beverages)
	Blood	Rinse with COLD water. Rub with bar soap. Or pretreat or soak with product containing enzymes. Wash using
		bleach safe for fabric.
	Candle wax, crayon	Scrape off surface wax. Place stain face down between paper towels. Press with warm iron until wax is absorbed.
		Replace paper towels frequently. Treat remaining stain with prewash stain remover or nonflammable dry cleaning
		fluid. Hand wash to remove solvent. Wash using bleach safe for fabric.
	Chocolate	Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.
	Collar or cuff soil, cosmetics	Pretreat with prewash stain remover or rub with bar soap.
	Dye transfer on white fabric	Use packaged color remover. Wash using bleach safe for fabric.
	Grass	Pretreat or soak in WARM water using product containing enzymes. Wash using bleach safe for fabric.
	Grease, oil, tar (butter, fats, salad	Scrape residue from fabric. Pretreat. Wash using hottest water safe for fabric. For heavy stains and tar, apply
	dressing, cooking oils, car grease,	nonflammable dry cleaning fluid to back of stain. Replace towels under stain frequently. Rinse throughly. Wash
	motor oils)	using hottest water safe for fabric.
	Ink	Some inks may be impossible to remove. Washing may set some inks. Use prewash stain remover, denatured
		alcohol or nonflammable dry cleaning fluid.
	Mildew, scorch	Wash with chlorine bleach if safe for fabric. Or, soak in oxygen bleach and HOT water before washing. Badly
		mildewed fabrics may be permanently damaged.
	Mud	Brush off dry mud. Pretreat or soak with product containing enzymes.
	Mustard, tomato	Pretreat with prewash stain remover. Wash using bleach safe for fabric.
	Nail polish	May be impossible to remove. Place stain face down on paper towels. Apply nail polish remover to back of stain.
		Repeat, replacing paper towels frequently. Do not use on acetate fabrics.
	Paint, varnish	WATER BASED : Rinse fabric in cool water while stain is wet. Wash. Once paint is dry, it cannot be removed,
		OIL BASED AND VARNISH : Use solvent recommended on can label. Rinse throughly before washing.
	Rust, brown or yellow	For spots, use rust remover safe for fabric. For discoloration of an entire load, use phosphate Detergent and
	discoloration	nonchlorine bleach. Do not use chlorine bleach because it may intensify discoloration.
	Shoe polish	LIQUID : Pretreat with a paste of granular Detergent and water. PASTE : Scrape residue from fabric. Pretreat with
		prewash stain remover or nonflammable dry cleaning fluid. Rub Detergent into dampened area, Wash using bleach
		safe for fabric.

16

<![if ! IE]>

<![endif]>Washing Program s

Washing Programs

Washing

POWER

Add

Add

the

Programs

AUTO OFF

the Detergent

laundry

1

2

4

(Normal Wash)

Used for normal loads, this

• Add the

appropriate

mode automatically selects the

most

appropriate conditions

quantity

of Detergent as

and

completes

the

sequence

indicated by the WATER

in one operation. The built-in

LEVEL next to

sensor detects the size of the

WATER DETERGENT.

load and the ideal wash

Or follow the Detergent

power and wash, rinse and

manufacturer’s

spin times are set accordingly.

instructions

1

3

2

5

Use this program for washing

•

Select

the

•

Use

neutral

delicate fabrics such as lingerie

and woolens. (wash only “water

WOOL

Detergent

washable” clothes)

program

on

appropriate for the

Before washing your woolens

the Control

laundry.

panel.

•

When washing

check the care label

for the

woolens use a mild

washing instructions.

Detergent

(wash only water washable

recommended for

clothes)

washing wool.

1

3

2

5

Use this mode when washing

• Select the

• Add the

appropriate

lightly soiled clothes

for a short

QUICK

quantity

of Detergentsa

time. The highly recommended

WASH

indicated by the

program on

WATER LEVEL next to

laundry amount

is under

2.0kg.

the Control

WATER DETERGENT.

panel.

Or follow the Detergent

manufacturer’s

instructions

1

3

2

5

Use Jean program when

• Spread

• Select the

washing Jeans of different

sizes

the jean

JEANS

evenly in

program on

the tub

the Control

panel.

1

3

2

5

Use this program to increase

rising performance.

•

Select the

This

would include

underwear

EXTRA

and

baby clothes.

CLEANING

If someone has

sensitive skin or

program on

skin

trouble,use

this

program.

the Control

panel.

START

Close the lid

Finish

Caution & Note

PAUSE

•

If water is already in the tub, or putting

3

5

6

wet laundry into the tub before starting

• The pulsator rotates for

• Water will be

• When the wash

•

will increase the WATER LEVEL.

With lightweight bulky loads, WATER

8 seconds to detect the

supplied for 2

program ends, the

•

LEVEL can be set low.

laundry load.

minutes after the

buzzer will ring

Changes to Water Temperature

• Then the WATER LEVEL

start of the wash to

for 10 seconds

(HOT/COLD) and wash level are

and the amount of

supplement the

before the Power

possible during operation.

Detergent to be used

water the laundry

goes off

(refer to page 14)

will be shown and

has absorbed.

automatically.

water will be supplied.

•

When setting the WATER LEVEL

4

6

7

manually, do not set to Medium to

prevent damage to laundry.

•

Washing with HOT water may damage

the laundry (Water is set to cold

automatically). Ensure that the load is

•

under 2kg.

In order to avoid damage to laundry,

the spin cycle may appear slow.

This also avoids wrinkles and clothing

may still contain some water. This is

normal.

•

When static pressure of water is more

than 2kg/cm2, the QUICK WASH course

4

6

7

will be within 19min.

4

6

7

4

6

7

17

<![if ! IE]>

<![endif]>ramsgPro ginhasW

FAVORITE Wash

Pressing the FAVORITE button allows you to store your FAVORITE wash conditions in the normal cycle memory and then recall it for use at a later time.

1 Press the POWER (AUTO OFF) button to turn power on.

POWER

AUTO OFF

2 Select the FAVORITE program.

19

<![if ! IE]>

<![endif]>ramsgPro ginhasW

3 Select your FAVORITE wash conditions.

•Press the TEMP. button to select wash Water Temperature.

•Press the WATER button to select

WATER.

•Press the WASH button, the RINSE button & the SPIN button to select wash time, rinse time & spin time respectively you want to store.

4 Press the START/PAUSE button to store & start your FAVORITE wash cycle. Power turns off automatically after wash.

START

PAUSE

NOTE

To recall your FAVORITE cycle.

1.Press POWER on.

2.Select the FAVORITE cycle by pressing the PROGRAM.

3.Press the START/PAUSE button. Then the wash cycle starts.

20

<![if ! IE]>

<![endif]>Washing Programs

SILENT Wash

Use this program to wash quietly in SILENT especially during late night and dawn.

1 Press the POWER (AUTO OFF) button to turn power on.

POWER

AUTO OFF

2 Press the PROGRAM button to select SILENT program.

3 Add the laundry into the washing tub.

4 Press the START/PAUSE button.

START

PAUSE

5 Add the Detergent and close the lid.

NOTE

•SILENT program takes longer washing time than FUZZY(Normal) program.

•To reduce noise in spinning, spin rpm is lower than normal spinning rpm. So the laundry has more moisture than normal.

TUB CLEAN

If scrud is allowed to build-up in the machine it can result in stains on your clothes or unpleasant smell in your washer.

Scrud is the way build-up that can occur within any washer when the fabric softener comes into contact with Detergent, and according to particular degree of dirtiness or quality of water to be use, in these case, use this program to clean inner tub and outer tub.

1 Press the POWER (AUTO OFF) button to turn power on.

	POWER
	AUTO OFF
2	Press the PROGRAM button to select the TUB CLEAN program.
		Ex-Large WATER is set automatically.
3	Press the START/PAUSE button.	• Left time is displayed.

START

PAUSE

4 After 10 minutes of water supplement. Add the oxygenated bleach (about 300 m ).

•Do not use Detergent box.

•Do not place any laundry inside tub.

	5	Close the lid.	• When the lid is open the machine will not operate, and an
			alarm signal will remind you to close the lid.

NOTE

•Before using this program remove lint inside lint filter.

•When using this program, do not place any laundry inside tub.

•This program takes about 3 hours to be completed.

•After using this program, remove dirt inside filter.

•After finishing this program, open the lid of wash to remove irritant odor.

•Do not pour bleach into the tub directly. It might cause damage the tub.

•Do not leave diluted oxygenated bleach inside tub for long time.

It rusts the tub must drain the remained diluted oxygenated water out.

•Use this program once for every month.

•Do not use this program repeatedly.

21

<![if ! IE]>

<![endif]>ramgPro Function ldditionaA

22

<![if ! IE]>

<![endif]>Additional Function Program

AIR DRY

AIR DRY for your laundary.

1 Press the POWER (AUTO OFF) button to turn power on.

POWER

AUTO OFF

2 Press the AIR DRY button to select the desired timing.

3 Press the START/PAUSE button.

START

PAUSE

4 Closed the lid.

NOTE

■Select "Air Dry" 30min TUB DRY

-Use this mode to keep inner tub from getting moldy caused by remaining moisture.

-Do not place any laundry inside tub.

-Use this mode once a week.

Caution) For better performance, put drain hose down to the floor so that water inside will be completely drained out.

■Select “Air Dry” above 1 hour

-Use this mode to reduce the drying time by minimizing remaining moisture on the laundry.

-In general, this is very effective on synthetic items(100% polyester).

-Do place laundry which is evenly distributed(Under 2kg).

- For normal clothes : Select 1 hour

- For synthetic items(100% polyester): Select 2 hours or 3 hours(on some models)

Option Washing

When you only need the Wash, Wash/Rinse or Rinse cycles, these can be set manually.

1 Press the POWER (AUTO OFF) button to turn power on.

POWER

AUTO OFF

2	Only Wash	Only Rinse	Only Spin
	Press the WASH button to	Press the RINSE button to	Press the SPIN button to
	select the desired timing.	select the desired times of	select the desired times of
		rinse.	spin.
	Only Wash,Rinse	Only Rinse,Spin	Only Drain
	Press the WASH button to	Press the RINSE button to	When you want to only
	select the desired timing.	select the desired times of	drain, wait until the water
		rinse.	in the washing tub drains
			completely.
	Press the RINSE button to
	select the desired times of	Press the SPIN button to
	rinse.	select the desired times of
		spin.
	You can use this option
	for preventing wrinkles of
	laundry

3 Press the WATER button, to control the water level according to the amount of laundry. If you do not choose anything, it is set the middle water level automatically.

4 Add the laundry into the washing tub.

5 Press the START/PAUSE button.

START

PAUSE

6 Add the detergent and close the lid.

NOTE

•When a Wash, Wash/Rinse or Rinse only option is selected, after the wash is completed the water will not be drained off. If you wish to drain the water, press SPIN button and wait until the water in the tub has drained completely. Then press the START/PAUSE button.

•If you do not specify the water level, then Medium will be automatically selected.

•If only Rinse is selected, the process will start from Water Supply.

23

<![if ! IE]>

<![endif]>ramgPro Function ldditionaA

24

<![if ! IE]>

<![endif]>Additional Function Program

DELAY START (RESERVATION) Wash

DELAY START (RESERVATION) Wash is used to delay the finishing time of the operation. The hours to be delayed can be set by the user accordingly.

The time on the display is the finishing time , not the start time.

1	Press the POWER (AUTO OFF) button to turn power on.
			POWER
			AUTO OFF
2	Press the PROGRAM button to select the washing program.
				• Select the program for laundry on the Control panel.
				This program will not work in WOOL and TUB CLEAN
				Program.
3	Press the DELAY START (RESERVATION) button.
				• The light will ‘DELAY’ turn on and
				‘TIME LEFT’	will be marked.
				• Press the button repeatedly to set the desired finishing time.
				For example, To finish washing in 9 hours from now, by
				make the number 9:00 pressing the DELAY START
				(RESERVATION ) button repeatedly.
				(RES.=DELAY)
4	Add the Detergent.			• The appropriate quantity of Detergent marked next to the

WATER of WATER•DETERGENT.

•When the lid is open the machine will not operate, and an alarm signal will remind you to close the lid

	5	Add the laundry and press the START/PAUSE button.
		START	• When you press the START/PAUSE button the light will
			blink.
		PAUSE
	6	Close the lid.	• Water will be supplied for 2 minutes after the start of the
			wash to supplement the water the laundry has absorbed.

Finish	• The washing will be finished according to the delayed time.

NOTE

•Finishing time can be delayed from 3~48 hours. Delaying from3~12 hours can be done in 1 hour time intervals and from 12~48 hours in 2 hour time intervals.

•If the lid is open, the machine will not work, and an alarm signal will alarm to remind you to close the lid.

•To select washing time, rinsing times, spinning time, water level, hot/cold or wash power manually, press the DELAY START (RESERVATION) button and select the desired option. Then press the START/PAUSE button.

•When the laundry cannot be taken out immediately after the wash program ends, it is better to omit the spinning program . (The laundry will be wrinkled if left for a long time after spinning.)