LG Electronics 42LM3450, 42LM345T-ZA, 42LM345S User Manual

0 (0)

Printed in KoreaP/NO : MFL67360737 (1209-REV00)

CHASSIS : LD21B

MODEL : 42LM3450/345S/345T

MODEL : 42LM3450/345S/345T-ZA

CAUTION

BEFORE SERVICING THE CHASSIS,

READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

LED LCD TV

SERVICE MANUAL

North/Latin America http://aic.lgservice.com

Europe/Africa http://eic.lgservice.com

Asia/Oceania http://biz.lgservice.com

Internal Use Only

- 2 -

Only for training and service purposes

CONTENTS

CONTENTS .............................................................................................. 2

SAFETY PRECAUTIONS ........................................................................ 3

SERVICING PRECAUTIONS ................................................................... 4

SPECIFICATION ...................................................................................... 6

ADJUSTMENT INSTRUCTION ............................................................. 11

BLOCK DIAGRAM ................................................................................. 17

EXPLODED VIEW .................................................................................. 20

SCHEMATIC CIRCUIT DIAGRAM ..............................................................

- 3 -

Only for training and service purposes

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in the

Schematic Diagram and Exploded View.

It is essential that these special safety parts should be replaced with the same components as recommended in this manual to prevent

Shock, Fire, or other Hazards.

Do not modify the original design without permission of manufacturer.

General Guidance

An isolation Transformer should always be used during the

servicing of a receiver whose chassis is not isolated from the AC

power line. Use a transformer of adequate power rating as this

protects the technician from accidents resulting in personal injury

from electrical shocks.

It will also protect the receiver and it's components from being

damaged by accidental shorts of th e cir cuitry that may be

inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this TV receiver is blown,

replace it with the specified.

When replacing a high wattage resistor (Oxide Metal Film Resistor,

over 1 W), keep the resistor 10 mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Before returning the receiver to the customer,

always perform an AC leakage current check on the exposed

metallic parts of the cabinet, such as antennas, terminals, etc., to

be sure the set is safe to operate without damage of electrical

shock.

Leakage Current Cold Check(Antenna Cold Check)

With the instrument AC plug removed from AC source, connect an

electrical jumper across the two AC plug prongs. Place the AC

switch in the on position, connect one lead of ohm-meter to the AC

plug prongs tied together and touch other ohm-meter lead in turn to

each exposed metallic parts such as antenna terminals, phone

jacks, etc.

If the exposed metallic part has a return path to the chassis, the

measured resistance should be between 1 MΩ and 5.2 MΩ.

When the exposed metal has no return path to the chassis the

reading must be infinite.

An other abnormality exists that must be corrected before the

receiver is returned to the customer.

Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.

Do not use a line Isolation Transformer during this check.

Connect 1.5 K / 10 watt resistor in parallel with a 0.15 uF capacitor

between a known good earth ground (Water Pipe, Conduit, etc.)

and the exposed metallic parts.

Measure the AC voltage across the resistor using AC voltmeter

with 1000 ohms/volt or more sensitivity.

Reverse plug the AC cord into the AC outlet and repeat AC voltage

measurements for each exp ose d metallic par t. Any voltage

measured must not exceed 0.75 volt RMS which is corresponds to

0.5 mA.

In case any measurement is out of the limits specified, there is

possibility of shock hazard and the set must be checked and

repaired before it is returned to the customer.

Leakage Current Hot Check circuit

IMPORTANT SAFETY NOTICE

SAFETY PRECAUTIONS

- 4 -

Only for training and service purposes

SERVICING PRECAUTIONS

CAUTION: Before servicing receivers covered by this service

manual and its supplements and addenda, read and follow the

SAFETY PRECAUTIONS on page 3 of this publication.

NOTE: If unforeseen circumstances create conict between the

following servicing precautions and any of the safety precautions

on page 3 of this publication, always follow the safety precautions.

Remember: Safety First.

General Servicing Precautions

1. Always unplug the receiver AC power cord from the AC power

source before;

a. Removing or reinstalling any component, circuit board mod-

ule or any other receiver assembly.

b. Disconnecting or reconnecting any receiver electrical plug or

other electrical connection.

c. Connecting a test substitute in parallel with an electrolytic

capacitor in the receiver.

CAUTION: A wrong part substitution or incorrect polarity

installation of electrolytic capacitors may result in an explo-

sion hazard.

2. Test high voltage only by measuring it with an appropriate

high voltage meter or other voltage measuring device (DVM,

FETVOM, etc) equipped with a suitable high voltage probe.

Do not test high voltage by "drawing an arc".

3. Do not spray chemicals on or near this receiver or any of its

assemblies.

4. Unless specied otherwise in this service manual, clean

electrical contacts only by applying the following mixture to the

contacts with a pipe cleaner, cotton-tipped stick or comparable

non-abrasive applicator; 10 % (by volume) Acetone and 90 %

(by volume) isopropyl alcohol (90 % - 99 % strength)

CAUTION: This is a ammable mixture.

Unless specied otherwise in this service manual, lubrication of

contacts in not required.

5. Do not defeat any plug/socket B+ voltage interlocks with which

receivers covered by this service manual might be equipped.

6. Do not apply AC power to this instrument and/or any of its

electrical assemblies unless all solid-state device heat sinks are

correctly installed.

7. Always connect the test receiver ground lead to the receiver

chassis ground before connecting the test receiver positive

lead.

Always remove the test receiver ground lead last.

8. Use with this receiver only the test xtures specied in this

service manual.

CAUTION: Do not connect the test xture ground strap to any

heat sink in this receiver.

Electrostatically Sensitive (ES) Devices

Some semiconductor (solid-state) devices can be damaged eas-

ily by static electricity. Such components commonly are called

Electrostatically Sensitive (ES) Devices. Examples of typical ES

devices are integrated circuits and some eld-effect transistors

and semiconductor “chip” components. The following techniques

should be used to help reduce the incidence of component dam-

age caused by static by static electricity.

1. Immediately before handling any semiconductor component or

semiconductor-equipped assembly, drain off any electrostatic

charge on your body by touching a known earth ground. Alter-

natively, obtain and wear a commercially available discharging

wrist strap device, which should be removed to prevent poten-

tial shock reasons prior to applying power to the unit under test.

2. After removing an electrical assembly equipped with ES

devices, place the assembly on a conductive surface such as

aluminum foil, to prevent electrostatic charge buildup or expo-

sure of the assembly.

3. Use only a grounded-tip soldering iron to solder or unsolder ES

devices.

4. Use only an anti-static type solder removal device. Some solder

removal devices not classied as “anti-static” can generate

electrical charges sufcient to damage ES devices.

5. Do not use freon-propelled chemicals. These can generate

electrical charges sufcient to damage ES devices.

6. Do not remove a replacement ES device from its protective

package until immediately before you are ready to install it.

(Most replacement ES devices are packaged with leads electri-

cally shorted together by conductive foam, aluminum foil or

comparable conductive material).

7. Immediately before removing the protective material from the

leads of a replacement ES device, touch the protective material

to the chassis or circuit assembly into which the device will be

installed.

CAUTION: Be sure no power is applied to the chassis or circuit,

and observe all other safety precautions.

8. Minimize bodily motions when handling unpackaged replace-

ment ES devices. (Otherwise harmless motion such as the

brushing together of your clothes fabric or the lifting of your

foot from a carpeted oor can generate static electricity suf-

cient to damage an ES device.)

General Soldering Guidelines

1. Use a grounded-tip, low-wattage soldering iron and appropriate

tip size and shape that will maintain tip temperature within the

range or 500 °F to 600 °F.

2. Use an appropriate gauge of RMA resin-core solder composed

of 60 parts tin/40 parts lead.

3. Keep the soldering iron tip clean and well tinned.

4. Thoroughly clean the surfaces to be soldered. Use a mall wire-

bristle (0.5 inch, or 1.25 cm) brush with a metal handle.

Do not use freon-propelled spray-on cleaners.

5. Use the following unsoldering technique

a. Allow the soldering iron tip to reach normal temperature.

(500 °F to 600 °F)

b. Heat the component lead until the solder melts.

c. Quickly draw the melted solder with an anti-static, suction-

type solder removal device or with solder braid.

CAUTION: Work quickly to avoid overheating the circuit

board printed foil.

6. Use the following soldering technique.

a. Allow the soldering iron tip to reach a normal temperature

(500 °F to 600 °F)

b. First, hold the soldering iron tip and solder the strand against

the component lead until the solder melts.

c. Quickly move the soldering iron tip to the junction of the

component lead and the printed circuit foil, and hold it there

only until the solder ows onto and around both the compo-

nent lead and the foil.

CAUTION: Work quickly to avoid overheating the circuit

board printed foil.

d. Closely inspect the solder area and remove any excess or

splashed solder with a small wire-bristle brush.

- 5 -

Only for training and service purposes

IC Remove/Replacement

Some chassis circuit boards have slotted holes (oblong) through

which the IC leads are inserted and then bent at against the cir-

cuit foil. When holes are the slotted type, the following technique

should be used to remove and replace the IC. When working with

boards using the familiar round hole, use the standard technique

as outlined in paragraphs 5 and 6 above.

Removal

1. Desolder and straighten each IC lead in one operation by

gently prying up on the lead with the soldering iron tip as the

solder melts.

2. Draw away the melted solder with an anti-static suction-type

solder removal device (or with solder braid) before removing

the IC.

Replacement

1. Carefully insert the replacement IC in the circuit board.

2. Carefully bend each IC lead against the circuit foil pad and

solder it.

3. Clean the soldered areas with a small wire-bristle brush.

(It is not necessary to reapply acrylic coating to the areas).

"Small-Signal" Discrete Transistor

Removal/Replacement

1. Remove the defective transistor by clipping its leads as close

as possible to the component body.

2. Bend into a "U" shape the end of each of three leads remaining

on the circuit board.

3. Bend into a "U" shape the replacement transistor leads.

4. Connect the replacement transistor leads to the corresponding

leads extending from the circuit board and crimp the "U" with

long nose pliers to insure metal to metal contact then solder

each connection.

Power Output, Transistor Device

Removal/Replacement

1. Heat and remove all solder from around the transistor leads.

2. Remove the heat sink mounting screw (if so equipped).

3. Carefully remove the transistor from the heat sink of the circuit

board.

4. Insert new transistor in the circuit board.

5. Solder each transistor lead, and clip off excess lead.

6. Replace heat sink.

Diode Removal/Replacement

1. Remove defective diode by clipping its leads as close as pos-

sible to diode body.

2. Bend the two remaining leads perpendicular y to the circuit

board.

3. Observing diode polarity, wrap each lead of the new diode

around the corresponding lead on the circuit board.

4. Securely crimp each connection and solder it.

5. Inspect (on the circuit board copper side) the solder joints of

the two "original" leads. If they are not shiny, reheat them and if

necessary, apply additional solder.

Fuse and Conventional Resistor

Removal/Replacement

1. Clip each fuse or resistor lead at top of the circuit board hollow

stake.

2. Securely crimp the leads of replacement component around

notch at stake top.

3. Solder the connections.

CAUTION: Maintain original spacing between the replaced

component and adjacent components and the circuit board to

prevent excessive component temperatures.

Circuit Board Foil Repair

Excessive heat applied to the copper foil of any printed circuit

board will weaken the adhesive that bonds the foil to the circuit

board causing the foil to separate from or "lift-off" the board. The

following guidelines and procedures should be followed whenever

this condition is encountered.

At IC Connections

To repair a defective copper pattern at IC connections use the

following procedure to install a jumper wire on the copper pattern

side of the circuit board. (Use this technique only on IC connec-

tions).

1. Carefully remove the damaged copper pattern with a sharp

knife. (Remove only as much copper as absolutely necessary).

2. carefully scratch away the solder resist and acrylic coating (if

used) from the end of the remaining copper pattern.

3. Bend a small "U" in one end of a small gauge jumper wire and

carefully crimp it around the IC pin. Solder the IC connection.

4. Route the jumper wire along the path of the out-away copper

pattern and let it overlap the previously scraped end of the

good copper pattern. Solder the overlapped area and clip off

any excess jumper wire.

At Other Connections

Use the following technique to repair the defective copper pattern

at connections other than IC Pins. This technique involves the

installation of a jumper wire on the component side of the circuit

board.

1. Remove the defective copper pattern with a sharp knife.

Remove at least 1/4 inch of copper, to ensure that a hazardous

condition will not exist if the jumper wire opens.

2. Trace along the copper pattern from both sides of the pattern

break and locate the nearest component that is directly con-

nected to the affected copper pattern.

3. Connect insulated 20-gauge jumper wire from the lead of the

nearest component on one side of the pattern break to the lead

of the nearest component on the other side.

Carefully crimp and solder the connections.

CAUTION: Be sure the insulated jumper wire is dressed so the

it does not touch components or sharp edges.

- 6 -

Only for training and service purposes

SPECIFICATION

NOTE : Specifications and others are subject to change without notice for improvement

1. Application range

This specification is applied to the LCD TV used LD21B

chassis.

2. Requirement for Test

Each part is tested as below without special appointment.

1) Temperature: 25 °C ± 5 °C(77 °F ± 9 °F), CST: 40 °C ± 5 °C

2) Relative Humidity: 65 % ± 10 %

3) Power Voltage

: Standard input voltage (AC 100-240 V~, 50/60 Hz)

* Standard Voltage of each products is marked by models.

4) Specification and performance of each parts are followed

ea ch drawing and s pe cificatio n b y p art number in

accordance with BOM.

5) The receiver must be operated for about 5 minutes prior to

the adjustment.

3. Test method

1) Performance: LGE TV test method followed

2) Demanded other specification

- Safety : CE, IEC specification

- EMC : CE, IEC

4. Model General Specification

No. Item Specication Remarks

1 Market EU(PAL Market-37Countries) DTV & Analog (Total 37 countries)

DTV (MPEG2/4, DVB-T) :37 countries

UK/Italy/Germany/France/Spain/Sweden/Finland/Nether-

lands/ Belgium/Luxemburg/ Greece/Denmark/Czech/

Austria /Hungary/Swiss/Croatia/Turkey

Norway/Slovenia/Poland/Ukraine/Portugal/Ireland/Morocco/

Latvia/Estonia/Lithania/Rumania/Bulgaria/Russia/Slovakia

Bosnia/Serbia/Albania/Kazakhstan/Belarus

DTV (MPEG2/4, DVB-T2): 8 countries

UK/Denmark/Sweden/Finland/Norway/Ireland/Ukraine/

Kazakhstan

DTV (MPEG2/4, DVB-C): 37 countries

UK/Italy/Germany/France/Spain/Sweden/Finland/

Netherlands/Belgium/Luxemburg/Greece/Denmark/Czech/

Austria /Hungary/Swiss/Croatia/Turkey Norway/Slovenia/

Poland/Ukraine/Portugal/Ireland/Morocco/ Latvia/Estonia/

Lithania/Rumania/Bulgaria/Russia/SlovakiaBosnia/Serbia/

Albania/Kazakhstan/Belarus

DTV (MPEG2/4,DVB-S): 29 countries

Italy/Germany/France/Spain/Netherlands/ Belgium/

Luxemburg/ Greece/ Czech/Austria /Hungary/Swiss/

Croatia/Turkey/Slovenia/Poland/Portugal/ Morocco/Latvia/

Estonia/Lithuania/Rumania/Bulgaria/Russia/Slovakia

Bosnia/Serbia/Albania/ Belarus

Supported satellite : 22 satellites

HISPASAT 1C/1D, ATLANTIC BIRD 2, NILESAT 101/102,

ATLANTIC BIRD 3, AMOS 2/3, THOR 5/6, IRIUS 4,

EUTELSAT-W3A, EUROBIRD 9A, EUTELSAT-W2A,

HOTBIRD 6/8/9, EUTELSAT-SESAT, ASTRA 1L/H/M/

KR, ASTRA 3A/3B, BADR 4/6, ASTRA 2D, EUROBIRD 3,

EUTELSAT-W7, HELLASSAT 2, EXPRESS AM1, TURK-

SAT 2A/3A, INTERSAT10

- 7 -

Only for training and service purposes

No. Item Specication Remarks

2 Broadcasting system

1) PAL-BG

2) PAL-DK

3) PAL-I/I’

4) SECAM L/L’

5) DVB-T/T2/C/S

3 Receiving system

Analog : Upper Heterodyne

Digital : COFDM, QAM

► DVB-T

- Guard Interval(Bitrate_Mbit/s)

1/4, 1/8, 1/16, 1/32

- Modulation : Code Rate

QPSK : 1/2, 2/3, 3/4, 5/6, 7/8

16-QAM : 1/2, 2/3, 3/4, 5/6, 7/8

64-QAM : 1/2, 2/3, 3/4, 5/6, 7/8

► DVB-T2

- Guard Interval(Bitrate_Mbit/s)

1/4, 1/8, 1/16, 1/32, 1/128, 19/128, 19/256,

- Modulation : Code Rate

QPSK : 1/2, 2/5, 2/3, 3/4, 5/6

16-QAM : 1/2, 2/5, 2/3, 3/4, 5/6

64-QAM : 1/2, 2/5, 2/3, 3/4, 5/6

256-QAM : 1/2, 2/5, 2/3, 3/4, 5/6

► DVB-C

- Symbolrate : 4.0Msymbols/s to 7.2Msymbols/s

- Modulation : 16QAM, 64-QAM, 128-QAM and 256-QAM

► DVB-S/S2

- symbolrate

DVB-S2 (8PSK / QPSK) : 2 ~ 45Msymbol/s

DVB-S (QPSK) : 2 ~ 45Msymbol/s

- viterbi

DVB-S mode : 1/2, 2/3, 3/4, 5/6, 7/8

DVB-S2 mode : 1/2, 2/3, 3/4, 3/5, 4/5, 5/6, 8/9, 9/10

4 Scart Jack (1EA) PAL, SECAM Scart 1 Jack is Full scart and support RF-OUT(analog).

5 Video Input RCA(1EA) PAL, SECAM, NTSC 4 System : PAL, SECAM, NTSC, PAL60

6 Component Input (1EA)

Y/Cb/Cr

Y/Pb/Pr

7 RGB Input RGB-PC

Analog(D-SUB 15PIN)

Some models (LD21A,LD21C) are not supported.

8 HDMI Input (3EA)

HDMI1-DTV/DVI

HDMI2-DTV

HDMI3-DTV

PC(HDMI version 1.3)

Support HDCP

The number of Input ports is different by model.

9 Audio Input (2EA)

RGB/DVI Audio

Component & AV

In case of the RGB/DVI Audio input,

Some models(LD21A,LD21C) are not supported.

Component & AV’s audio input is used by common port.

10 SDPIF out (1EA) SPDIF out Some models(LD21A,LD21C) are not supported.

11 Earphone out (1EA)

Antenna, AV1, AV2, Component, RGB,

HDMI1, HDMI2, HDMI3

Some models(LD21A,LD21C) are not supported.

12 USB (1EA or 2EA)

EMF,

DivX HD,

For SVC (download)

JPEG, MP3, DivX HD

LM58, CM96: 2EA

LS56, LS35, CS46, LS,34, LM34 : 1EA

13 DVB

DVB-T

CI : UK, Finland, Denmark, Norway, Sweden, Russia,

Spain, Ireland, Luxemburg, Belgium, Netherland

CI+ : France(Canal+), Italy(DGTVi)

DVB-C

CI : Switzerland, Austria, Slovenia, Hungary, Bulgaria

CI+ : Switzerland(UPC,Cablecom), Netherland(Ziggo),

Germany(KDG,CWB), Finland(labwise)

DVB-S CI + : Germany(Astra HD+ )

14 Ethernet (1EA) DLNA(Wired, DMP only) Some models (LD21A,LD21C) are not supported.

- 8 -

Only for training and service purposes

5. Video resolutions (2D)

5.1. Component Input (Y, CB/PB, CR/PR)

5.2. RGB Input (PC) - HD Model

No. Resolution H-freq(kHz) V-freq(Hz) Pixel clock(MHz) Proposed

1 720*576 15.625 50.00 13.5 SDTV ,DVD 576I

2 720*480 15.73 60.00 13.5135 SDTV ,DVD 480I

3 720*480 15.73 59.94 13.50 SDTV ,DVD 480I

4 720*576 31.25 50.00 27.00 SDTV 576P

5 720*480 31.50 60.00 27.027 SDTV 480P

6 720*480 31.47 59.94 27.00 SDTV 480P

7 1280*720 37.50 50.00 74.25 HDTV 720P

8 1280*720 45.00 60.00 74.25 HDTV 720P

9 1280*720 44.96 59.94 74.176 HDTV 720P

10 1920*1080 28.125 50.00 74.25 HDTV 1080I

11 1920*1080 33.75 60.00 74.25 HDTV 1080I

12 1920*1080 33.72 59.94 74.176 HDTV 1080I

13 1920*1080 56.25 50.00 148.50 HDTV 1080P

14 1920*1080 67.50 60.00 148.50 HDTV 1080P

15 1920*1080 67.432 59.94 148.352 HDTV 1080P

16 1920*1080 27.00 24.00 74.25 HDTV 1080P

17 1920*1080 26.97 23.94 74.176 HDTV 1080P

18 1920*1080 33.75 30.00 74.25 HDTV 1080P

19 1920*1080 33.71 29.97 74.176 HDTV 1080P

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed DDC

1 640*480 31.469 59.94 25.17 VESA(VGA) O

2 800*600 37.879 60.31 40.00 VESA(SVGA) O

3 1024*768 48.363 60.00 65.00 VESA(XGA) O

4 1152*864 54.348 60.053 80.00 VESA O

5.3. RGB Input (PC) - FHD Model

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed DDC

1 640*350 31.468 70.09 25.17 EGA X

2 720*400 31.469 70.08 28.32 DOS O

3 640*480 31.469 59.94 25.17 VESA(VGA) O

4 800*600 37.879 60.31 40.00 VESA(SVGA) O

5 1024*768 48.363 60.00 65.00 VESA(XGA) O

6 1152*864 54.348 60.053 80.00 VESA O

7 1360*768 47.712 60.015 85.50 VESA (WXGA) O

8 1920*1080 67.5 60 148.5 HDTV 1080P O

- 9 -

Only for training and service purposes

5.4. HDMI Input(PC/DTV)

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed Remark

PC(DVI) DDC

1 640*350 31.468 70.09 25.17 EGA X

2 720*400 31.469 70.08 28.32 DOS O

3 640*480 31.469 59.94 25.17 VESA(VGA) O

4 800*600 37.879 60.31 40.00 VESA(SVGA) O

5 1024*768 48.363 60.00 65.00 VESA(XGA) O

6 1152*864 54.348 60.053 80.00 VESA O

7 1360*768 47.712 60.015 85.50 VESA (WXGA) O

8 1280*1024 63.981 60.020 108.0 VESA (SXGA) O FHD only

9 1920*1080 67.50 60.00 148.5 HDTV 1080P O FHD only

DTV

1 720*480 31.47 59.94 27.00 SDTV 480P

2 720*480 31.50 60.00 27.027 SDTV 480P

3 720*576 31.250 50.00 27.00 SDTV 576P

4 1280*720 37.50 50.00 74.25 HDTV 720P

5 1280*720 45.00 60.00 74.25 HDTV 720P

6 1280*720 44.96 59.94 74.176 HDTV 720P

7 1920*1080 28.125 50.00 74.25 HDTV 1080I

8 1920*1080 33.75 60.00 74.25 HDTV 1080I

9 1920*1080 33.72 59.94 74.176 HDTV 1080I

10 1920*1080 56.250 50.00 148.50 HDTV 1080P

11 1920*1080 67.50 60.00 148.50 HDTV 1080P

12 1920*1080 67.432 59.94 148.352 HDTV 1080P

13 1920*1080 27.00 24.00 74.25 HDTV 1080P

14 1920*1080 26.97 23.976 74.176 HDTV 1080P

15 1920*1080 33.75 30.00 74.25 HDTV 1080P

- 10 -

Only for training and service purposes

6. Video resolutions (3D)

6.1. HDMI Input

No. Resolution H-freq(kHz) V-freq(Hz) Pixel clock(MHz) Proposed 3D input proposed mode

1. 1920*1080 53.95 / 54 23.98 / 24 148.35/148.5 HDTV 1080P Frame packing

2. 1280*720 89.9 / 90 59.94/60 148.35/148.5 HDTV 720P Frame packing

3. 1280*720 75 50 148.5 HDTV 720P Frame packing

4 1920*1080 67.5 60 148.5 HDTV 1080P Side by Side(half), Top and bottom

5 1920*1080 56.3 50 148.5 HDTV 1080P Side by Side(half), Top and bottom

6 1280*720 45 60 74.25 HDTV 720P Side by Side(half), Top and Bottom

7 1280*720 37.5 50 74.25 HDTV 720P Side by Side(half), Top and Bottom

8 1920*1080 33.7 60 74.25 HDTV 1080i Side by Side(half), Top and Bottom

9 1920*1080 28.125 50 74.25 HDTV 1080i Side by Side(half), Top and Bottom

10 1920*1080 27 24 74.25 HDTV 1080P Side by Side(half), Top and Bottom

11 1920*1080 33.7 30 89.1 HDTV 1080P Side by Side(half), Top and Bottom

6.2. RF 3D Input(DTV)

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed 3D input proposed mode

1. 1280*720 37.500 50 74.25 HDTV 720P Side by Side, Top & Bottom

2. 1920*1080 28.125 50 74.25 HDTV 1080I Side by Side, Top & Bottom

6.3. USB Input

6.4. RGB-PC Input

6.5. DLNA Input

6.6. 3D Input mode

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed 3D input proposed mode

1. 1920*1080 33.75 30.000 74.25 HDTV 1080P

Side by Side, Top & Bottom **support

MPO(Photo)

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed 3D input proposed mode

1. 1920*1080 66.587 59.93 148.50 HDTV 1080p Side by Side, Top & Bottom

No. Resolution H-freq(kHz) V-freq.(Hz) Pixel clock(MHz) Proposed 3D input proposed mode

1. 1920*1080 33.75 30 74.25 HDTV 1080p Side by Side, Top & Bottom

No. Side by Side Top & Bottom Single Frame Sequential Frame Packing

- 11 -

Only for training and service purposes

ADJUSTMENT INSTRUCTION

1. Application Range

This specification sheet is applied to all of the LCD TV with

LD21B chassis.

2. Designation

(1) The adjustment is according to the order which is designated

and which must be followed, according to the plan

which

can be changed only on agreeing.

(2) Power adjustment : Free Voltage.

(3) Magnetic Field Condition: Nil.

(4) Input signal Unit: Product Specification Standard.

(5) Reserve after operation : Above 5 Minutes (Heat Run)

Temperature : at 25 °C ± 5 °C

Relative humidity : 65 ± 10 %

Input voltage : 220 V, 60 Hz

(6) Adjustment equipments: Color Analyzer(CA-210 or CA-110),

DDC Adjustment Jig, Service remote control.

(7) Push the "IN STOP" key - For memory initialization.

3. Main PCB check process

▪ APC - After Manual-Insert, executing APC

* Boot file Download

(1) Execute ISP program "Mstar ISP Utility" and then click

"Config" tab.

(2) Set as below, and then click "Auto Detect" and check "OK"

message.

If "Error" is displayed, check connection between computer,

jig, and set.

(3) Click "Read" tab, and then load download file(XXXX.bin)

by clicking "Read"

(4) Click "Connect" tab. If "Can't" is displayed, check connection

between computer, jig, and set.

(5) Click "Auto" tab and set as below.

(6) Click "Run".

(7) After downloading, check "OK" message.

* USB DOWNLOAD

(1) Put the USB Stick to the USB socket.

(2) Automatically detecting update file in USB Stick.

- If your downloaded program version in USB Stick is Low,

it didn't work. But your downloaded version is High, USB

data is automatically detecting.

(3) Show the message "Copying files from memory".

(4) Updating is starting.

(5) Updating Completed, The TV will restart automatically.

(6) If your TV is turned on, check your updated version and

Tool option. (explain the Tool option, next stage)

* If downloading version is more high than your TV have, TV

can lost all channel data. In this case, you have to channel

recover. if all channel data is cleared, you didn’t have a DTV/

ATV test on production line.

* After downloading, have to adjust Tool Option again.

(1) Push "IN-START" key in service remote control.

(2) Select "Tool Option 1" and push "OK" key.

(3) Punch in the number. (Each model has their number)

(1)

filexxx.bin

(4)

(5)

(6)

(7)...........OK

filexxx.bin

(2)

(3)

Please Check the Speed :

To use speed between

from 200KHz to 400KHz

Case1 : Software version up

1. After downloading S/W by USB , TV set will reboot

automatically.

2. Push “In-stop” key.

3. Push “Power on” key.

4. Function inspection

5. After function inspection, Push “In-stop” key.

Case2 : Function check at the assembly line

1. When TV set is entering on the assembly line, Push

“In-stop” key at rst.

2. Push “Power on” key for turning it on.

→ If you push “Power on” key, TV set will recover

channel information by itself.

3. After function inspection, Push “In-stop” key.

- 12 -

Only for training and service purposes

3.1. ADC Process

(1) ADC

- Enter Service Mode by pushing "ADJ" key,

- Enter Internal ADC mode by pushing "►" key at "7. ADC

Calibration".

<Caution> Using "power on" key of the Adjustment remote

control, power on TV.

* ADC Calibration Protocol (RS232)

Adjust Sequence

▪ aa 00 00 [Enter Adjust Mode]

▪ xb 00 40 [Component1 Input (480i)]

▪ ad 00 10 [Adjust 480i Comp1]

▪ xb 00 60 [RGB Input (1024*768)] (only LD21B)

▪ ad 00 10 [Adjust 1024*768 RGB] (only LD21B)

▪ aa 00 90 End Adjust mode

* Required equipment : Adjustment remote control.

3.2. EDID Download

▪ After enter Service Mode by pushing "ADJ" key.

▪ Enter EDID D/L menu.

▪ Enter "START" by pushing "OK" key.

<Caution> Never connect HDMI && D-sub cable when EDID

downloaded.

3.3. EDID data

(1) FHD RGB EDID data (RGB input : only LD21B support)

(2) FHD HDMI EDID data

(3) Detail EDID Options are below

a. Product ID

b. Serial No: Controlled on production line.

c. Month, Year: Controlled on production line:

ex) Week : '01' -> '01'

Year : '2012' -> '16' fix

d. Model Name(Hex):

cf) TV set’s model name in EDID data is below.

e. Checksum: Changeable by total EDID data.

f. Vendor Specific(HDMI)

EZ ADJUST

0. Tool Option1

1. Tool Option2

. Tool Option3

. Tool Option4

. Tool Option 5

. Country Group

6. Area Option

. ADC Calibration ඖ

8. White Balance

. 10 Point WB

. Test Pattern

1. EDID D/L

2. Sub B/C

3. Touch Sensitivity Setting

ADC Calibration

ADC Comp 480i NG

ADC Comp 1080p NG

ADC RGB NG

Start Reset

NO Item CMD 1 CMD 2 Data 0

Enter

Adjust MODE

Adjust

‘Mode In’

A A 0 0

When transfer the ‘Mode In’,

Carry the command.

ADC adjust ADC Adjust A D 1 0

Automatically adjustment

(The use of a internal pattern)

0 1 2 3 4 5 6 7 8 9 A B C D E F

00 00 FF FF FF FF FF FF 00 1E 6D a b

10 c 01 03 68 A0 5A 78 0A EE 91 A 3 54 4C 99 26

20 0F 5 0 5 4 A1 0 8 0 0 31 40 45 40 61 40 71 4 0 81 80

30 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C

40 45 00 A0 5A 00 00 0 0 1E 66 21 50 B0 51 00 1B 3 0

50 40 70 36 00 A0 5A 00 0 0 0 0 1E 0 0 0 0 00 FD 00 3A

60 3E 1E 53 10 00 0A 2 0 20 20 20 20 20 d

70 d 00 e

0 1 2 3 4 5 6 7 8 9 A B C D E F

00 00 FF FF FF FF FF FF 00 1E 6D a b

10 c 01 03 80 A0 5A 78 0A EE 91 A3 54 4C 99 26

20 0F 50 54 A1 08 00 31 40 45 40 61 40 71 40 81 80

30 01 01 01 01 01 01 02 3A 80 18 71 38 2D 40 58 2C

40 45 00 A0 5A 00 00 00 1E 66 21 50 B0 51 00 1B 30

50 40 70 36 00 A0 5A 00 00 00 1E 00 00 00 FD 00 3A

60 3E 1E 53 10 00 0A 20 20 20 20 20 20 d

70 d 01 e

80 02 03 33 F1 4E 10 9F 04 13 05 14 03 02 12 20 21

90 22 15 01 26 15 07 50 09 57 07 f

A0 80 1E 20 C0 0E 01 40 0A 0F 08 10 18 10 98 10 58

B0 10 38 10 01 1D 80 18 71 1C 16 20 58 2C 25 00 20

C0 C2 31 00 00 9E 01 1D 00 72 51 D0 1E 20 6E 28 55

D0 00 20 C2 31 00 00 1E 02 3A 80 18 71 38 2D 40 58

E0 2C 45 00 A0 5A 00 00 00 1E 01 1D 00 BC 52 D0 1E

F0 20 B8 28 55 40 C4 8E 21 00 00 1E 00 00 00 00 e

EZ ADJUST

0. Tool Option1

1. Tool Option2

. Tool Option3

. Tool Option4

. Tool Option 5

. Country Group

6. Area Option

7. ADC Calibration

ඖ

8. White Balance

. 10 Point WB

. Test Pattern

1. EDID D/L

2. Sub B/C

3. Touch Sensitivity Setting

EDID D/L

HDMI1

HDMI2

HDMI3

RGB

Start Reset

MODEL NAME HEX EDID Table DDC Function

HD/FHD Model 0001 01 00 Analog/Digital

Model name MODEL NAME(HEX)

LG TV 00 00 00 FC 00 4C 47 20 54 56 0A 20 20 20 20 20 20 20 (LG TV)

EDID C/S data

FHD

HDMI RGB

Check sum

(Hex)

Block 0 43 5C

Block 1

23 (HDMI1)

-13 (HDMI2)

03 (HDMI3)

Input Model name(HEX)

HDMI1 78030C001000

HDMI2 78030C002000

HDMI3 78030C003000

- 13 -

Only for training and service purposes

3.4 Function Check

- Check display and sound

■ Check Input and Signal items.

1) TV

2) AV (SCART / CVBS)

3) COMPONENT (480i)

4) RGB(PC: 1024 x 768 @ 60hz)(* RGB input: LD21B only

support)

5) HDMI

6) PC Audio In (* except LD21A chassis model)

* Display and Sound check is executed by Remote control.

Not to push the INSTOP key after completion if the function

inspection.

4. Total Assembly line process

4.1. Adjustment Preparation

▪ W/B Equipment condition

CA210

: CCFL/EEFL -> CH9, Test signal: Inner pattern(80IRE)

LED -> CH14, Test signal: Inner pattern(80IRE)

▪ If it is executed W/B adjustment in 2~3 minutes H/run, it is

adjusted by Target data

▪ Edge LED W/B Table in process of time (LGD module & 65”

AUO module)

* Connecting picture of the measuring instrument

(On Automatic control)

Inside PATTERN is used when W/B is controlled. Connect to

auto controller or push Adjustment R/C POWER ON →

Enter the mode of White-Balance, the pattern will come out.

* Auto-control interface and directions

(1) Adjust in the place where the influx of light like floodlight

around is blocked. (illumination is less than 10 lux).

(2) Adhere closely the Color analyzer(CA210) to the module

less than 10 cm distance, keep it with the surface of the

Module and Color analyzer's prove vertically.(80° ~ 100°).

(3) Aging time

- After aging start, keep the power on (no suspension of

power supply) and heat-run over 5 minutes.

- Using 'no signal' or 'POWER ONLY' or the others, check

the back light on.

▪ Auto adjustment Map(using RS-232C to USB cable)

RS-232C COMMAND

[CMD ID DATA]

Wb 00 00 White Balance Start

Wb 00 ff White Balance End

Color Temperature : COOL, Medium, Warm.

One of R Gain/G Gain/ B Gain should be kept on 0xC0, and

adjust other two lower than C0.(When R/G/B Gain are all

C0, it is the FULL Dynamic Range of Module)

Mode Temp Coordinate spec Target

Cool 13,000k

X=0.269 (±0.002)

Y=0.273 (±0.002)

X=0.271

Y=0.276

Inner pattern

(204gray,

80IRE)

Medium 9,300k

X=0.285 (±0.002)

Y=0.293 (±0.002)

X=0.287

Y=0.296

Warm 6,500k

X=0.313 (±0.002)

Y=0.329 (±0.002)

X=0.315

Y=0.332

Aging

time

(Min)

Cool Medium Warm

X y x y x y

269 273 285 293 313 329

1 0-2 280 287 296 307 320 337

2 3-5 279 285 295 305 319 335

3 6-9 277 284 293 304 317 334

4 10-19 276 283 292 303 316 333

5 20-35 274 280 290 300 314 330

6 36-49 272 277 288 297 312 327

7 50-79 271 275 287 295 311 325

8 80-119 270 274 286 294 310 324

9 Over 120 269 273 285 293 309 323

Full White Pattern

CA-210

COLOR

ANALYZER

TYPE : CA-210

RS-232C Communication

RS-232C COMMAND

[CMD ID DATA]

MIN

CENTER

(DEFAULT)

MAX

Cool Mid Warm Cool Mid Warm

R Gain jg Ja jd 00 172 192 192 192

G Gain jh Jb je 00 172 192 192 192

B Gain ji Jc jf 00 192 192 172 192

R Cut 64 64 64 128

G Cut 64 64 64 128

B Cut 64 64 64 128

- 14 -

Only for training and service purposes

* Manual W/B process using adjust Remote control.

▪ After enter Service Mode by pushing "ADJ" key,

▪ Enter White Balance by pushing "

►

" key at "8. White

Balance".

* After you finished all adjustments, Press "In-start" key and

compare Tool option and Area option value with its BOM, if

it is correctly same then unplug the AC cable. If it is not

same, then correct it same with BOM and unplug AC cable.

For correct it to the model's module from factory Jig model.

* Push the "IN STOP" key after completing the function

inspection. And Mechanical Power Switch must be set

“ON”.

4.2. EYE-Q function check

(1) Turn on TV.

(2) Press EYE key of Adjustment remote control.

(3) Cover the Eye Q II sensor on the front of the using your

hand and wait for 6 seconds.

(4) Confirm that R/G/B value is lower than 10 of the "Raw

Data (Sensor data, Back light)". If after 6 seconds, R/G/B

value is not lower than 10, replace Eye Q II sensor.

(5) Remove your hand from the Eye Q II sensor and wait for 6

seconds.

(6) Confirm that "ok" pop up. If change is not seen, replace

Eye Q II sensor.

4.3. 3D function test

(Pattern Generator MSHG-600, MSPG-6100[Support HDMI1.4])

* HDMI mode NO. 872 , pattern No.83

(1) Please input 3D test pattern like below. (HDMI mode No.

872 , pattern No.83)

(2) When 3D OSD appear automatically , then select OK key.

(3) Don't wear a 3D Glasses, Check the picture like below.

4.4. IR emitter inspection

(1) Start 3D pattern inspection.

(2) If IR emitter signal is correctly received to IR receiver, the

lamp of IR tester turn on.

EZ ADJUST

0. Tool Option1

1. Tool Option2

2. Tool Option3

3. Tool Option4

4. Tool Option5

5. Country Group

6. Area Option

7. ADC Calibration

8. White Balance ►

9. 10 Point WB

10. Test Pattern

11. EDID D/L

12. Sub B/C

13. Touch Sensitivity Setting

White Balance

Color Temp.

R-Gain

G-Gain

B-Gain

R-Cut

G-Cut

B-Cut

Test-Pattern

Backlight

Reset

Cool

172

192

100

To Set

- 15 -

Only for training and service purposes

4.5. Outgoing condition Configuration

■ When pressing IN-STOP key by SVC remocon, Red LED

are blinked alternatively. And then automatically turn off.

(Must not AC power OFF during blinking)

5. HI-POT Test

5.1. HI-POT auto-check preparation

- Check the POWER cable and SIGNAL cable insertion condition

5.2. HI-POT auto-check

(1) Pallet moves in the station. (POWER CORD / AV CORD is

tightly inserted)

(2) Connect the AV JACK Tester.

(3) Controller (GWS103-4) on.

(4) HI-POT test (Auto)

- If Test is failed, Buzzer operates.

- If Test is passed, GOOD Lamp on and move to next proc-

ess automatically.

5.3. Checkpoint

(1) Test voltage

- Touchable Metal : 3KV / min at 100mA

- SIGNAL : 3KV / min at 100mA

(2) TEST time: 1 second. (case : mass production )

(3) TEST POINT

- Touchable Metal => LIVE & NEUTRAL : Touchable Metal.

- SIGNAL => LIVE & NEUTRAL : SIGNAL.

6. Model name & Serial number D/L

▪ Press "Power on" key of service remote control.

(Baud rate : 115200 bps)

▪ Connect USB to RS232 Signal Cable to USB Jack.

▪ Write Serial number.

▪ Must check the serial number at the Diagnostics of SET UP

menu. (Refer to below).

6.1. Signal Table

CMD : A0h

LENGTH : 85~94h (1~16 bytes)

ADH : EEPROM Sub Address high (00~1F)

ADL : EEPROM Sub Address low (00~FF)

Data : Write data

CS : CMD + LENGTH + ADH + ADL + Data_1 +...+ Data_n

Delay : 20ms

6.2. Comand Set

* Description

FOS Default write : <7mode data> write

Vtotal, V_Frequency, Sync_Polarity, Htotal, Hstart, Vstart, 0,

Phase

Data write : Model Name and Serial Number write in EEPROM,.

6.3. Method & notice

(1) Serial number D/L is using of scan equipment.

(2) Sett ing of scan equ ipm ent operated by Manufac turing

Technology Group.

(3) Serial number D/L must be conformed when it is produced in

production line, because serial number D/L is mandatory by

D-book 4.0.

* Manual Download(Model Name and Serial Number)

If the TV set is downloaded by OTA or Service man, sometimes

model name or serial number is initialized.(Not always)

There is impossible to download by bar code scan, so It need

Manual download.

1) Press the "Instart" key of Adjustment remote control.

2) Go to the menu "6.Model Number D/L" like below photo.

3) Input the Factory model name or Serial number like photo.

4) Check the model name Instart menu.

→

Factory name displayed.

(ex 32LV3400-ZG)

5) Check the Diagnostics.(DTV country only) → Buyer model

displayed.(ex 32LV3400-ZG)

CMD LENGTH ADH ADL DATA_1 . . . Data_n CS DELAY

Adjust mode CMD(hex) LENGTH(hex) Des cription

EEPROM WRITE A0h 84h+n n-bytes Write (n = 1~16)

- 16 -

Only for training and service purposes

7. MAC Address & CI+ key download

7.1 MAC Address

7.1.1 Equipment & Condition

▪ Play file : Serial.exe

▪ MAC Address edit

▪ Input Start / End MAC address

7.1.2 Download method

(1) Communication Prot connection

Connection : PCBA (USB Port) → USB to Serial Adapter

(UC-232A) → RS-232C cable → PC(RS-232C port)

* Caution : LJ21* chassis support only UC-232A driver. (only

use this one. )

(2) MAC Address & CI+ Key Download

▪ Set CI+ Key path Directory at Start Mac & CI+ Download

Programme

▪ Com 1,2,3,4 and 115200(Baudrate)

▪ Port connection button click(1)

▪ Push the (2) MAC Address write.

▪ At success Download, check the OK (3).

▪ Start CI+ Key Download, Push the (4).

▪ Check the OK or NG.

7.2 LAN Inspection

7.2.1. Equipment & Condition

▪ Each other connection to LAN Port of IP Hub and Jig

7.2.2. LAN inspection solution

▪ LAN Port connection with PCB

▪ Network setting at MENU Mode of TV

▪ Setting automatic IP

▪ Setting state confirmation

-> If automatic setting is finished, you confirm IP and MAC

Address.

7.3. LAN PORT INSPECTION(PING TEST)

Connect SET -> LAN port == PC -> LAN Port

7.3.1. Equipment setting

(1) Play the LAN Port Test PROGRAM.

(2) Input IP set up for an inspection to Test Program.

*IP Number : 12.12.2.2

7.3.2. LAN PORT inspection (PING TEST)

(1) Play the LAN Port Test Program.

(2) Connect each other LAN Port Jack.

(3) Play Test (F9) button and confirm OK Message.

(4) Remove LAN cable.

GP4_LOW

SET PC

- 17 -

Only for training and service purposes

Ethernet

RGB PC

SPDIF

Component1

HDMI1/2(DVI)

PC/DVI Audi I

IF +/-

TU_CVBS

SIF

L/R

LG2111A

IC101

SERIAL FLASH

IC1401 (8M bit)

MX25L8005M2I

LVDS

(FHD/50Hz)

Audio AMP

STA380BWE

USB1

DP/DM

SPK L/R

X-tal

24M

FPC(51P)

I2S

SPDIF

CVBS, Y/Pb/Pr, L/R

RGB/H/V

Rear

TMDS

DDR3 Add.

DDR3 Data

SPI

Side

NAND FLASH

IC102 (2Gbit)

PCM_A[0:7]

TMDS

HDMI3

DDR3 1Gb

IC1202

H5TQ1G63BFR

DDR3 1Gb

IC1201

H5TQ1G63BFR

CONTROL

IR & LED /

SOFT TOUCH

(TACT SWITCH)

SENSOR

_SCL/SDA

LED_R

KEY1

KEY2

M24M01-HRMN6TP

IC104 256Kbit

I2C

Except of

LS3500/CS460

F-SCART

SC1_CVBS_IN

SC1_R/G/B

FE_ VOUT

CI Slot

74LCX244

Buffer

TS_DATA[0:7]

PCM_DATA[0:7]

FE_TS_DATA[0:7]

PCM_A[8:14]

USB2

DP/DM

EPHY

TDSS

G101D

(LGIT)

BLOCK DIAGRAM

Applied Model : 42LM3450

+ 38 hidden pages