BL220 series,
BL230 series
BL240 series
instructions
HEAD OFFICE: Kenwood Limited, 1-3 Kenwood Business Park, New Lane, Havant, Hampshire PO9 2NH
English |
2 - 6 |
w´¸∂ |
7-01 |
41089/1
English
|
|
|
|
Use your blender for soups, drinks, |
|
|
|
|
|
|
|
|
|
pâtés, mayonnaise, breadcrumbs, |
|
|
|
|
biscuit crumbs, chopping nuts and |
|
|
|
|
crushing ice. Use your mill (if |
|
|
|
|
supplied) for milling herbs, nuts, |
|
|
|
|
coffee beans and purées. |
a |
b |
|
|
before using your Kenwood |
|
|
appliance |
||
|
|
|
● |
Read these instructions carefully and |
|
|
retain for future reference. |
||
|
|
|
|
|
|
|
|
● Remove all packaging and any |
|
|
|
|
|
labels. |
|
|
|
● Wash the parts: see ‘care and |
|
|
|
|
|
cleaning’. |
|
|
|
safety |
|
|
|
|
|
|
|
|
|
● Switch off and unplug: |
|
|
|
|
● |
before fitting or removing parts; |
|
|
|
● |
when not in use; |
|
|
|
● |
before cleaning. |
|
|
|
● Never fit the blade unit to the |
|
|
|
|
power unit without the |
|
|
|
|
blender goblet or mill jar |
|
|
|
|
fitted. |
|
|
|
|
● Always unplug the appliance before |
|
|
|
|
putting your hands or utensils in the |
|
|
|
|
goblet. |
|
|
|
|
● Always take care when handling the |
|
|
|
blade assembly and avoid touching |
||
|
|
|
the cutting edge of the blades when |
|
|
|
cleaning. |
||
|
|
|
● Only operate the blender with the lid |
|
|
|
|
in place. |
|
|
● Only use the goblet with the blade |
|||
|
|
|||
|
|
|
assembly supplied. |
|
|
|
|
● Never let the power unit, cord or |
|
|
|
|
plug get wet. |
|
|
|
|
● Never use a damaged appliance. |
|
|
|
|
Get it checked or repaired: see |
|
|
|
|
‘service and customer care’. |
|
|
|
● Never use an unauthorised |
||
|
|
|
||
|
|
|
attachment. |
|
|
|
|
● Liquids should be allowed to cool to |
|
|
|
|
room temperature before blending. |
|
|
|
|
● Never leave the appliance |
|
|
|
|
unattended when it is operating. |
|
●When removing the blender or mill from the power unit:
●wait until the blades have completely stopped;
●don’t accidentally unscrew the goblet or mill jar from the blade assembly.
●Never run the blender empty.
●Never blend more than the maximum capacity stated in the recommended speed chart.
●To ensure long life of your blender, do not run it for longer than 60 seconds or the mill for longer than 30 seconds in any 5 minute period.
●Smoothie recipes - never blend frozen ingredients that have formed a solid mass during freezing, break it up before adding to the goblet.
●Don’t use the blender as a storage container. Keep it empty before and after use.
●Always use the blender on a secure, dry level surface.
●Never place this appliance on or near a hot gas or electric burner or where it could touch a heated appliance.
●Important - The skirt on the base of the glass goblet is fitted during manufacture and no attempt should be made to remove it.
●Misuse of your blender can result in injury.
●This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
●Children should be supervised to ensure that they do not play with the appliance.
●Only use the appliance for its intended domestic use. Kenwood will not accept any liability if the appliance is subject to improper use, or failure to comply with these instructions.
2
before plugging in
●Make sure your electricity supply is the same as the one shown on the underside of the appliance.
Important - UK only
●The wires in the cord are coloured as follows:
Blue = Neutral Brown = Live.
●The appliance must be protected by a 3A approved (BS1362) fuse.
Note:
●For non-rewireable plugs the fuse cover MUST be refitted when replacing the fuse. If the fuse cover is lost then the plug must not be used until a replacement can be obtained. The correct fuse cover is identified by colour and a replacement may be obtained from your Kenwood Authorised Repairer (see Service).
●If a non-rewireable plug is cut off it must be DESTROYED IMMEDIATELY.An electric shock hazard may arise if an unwanted non-rewireable plug is inadvertently inserted into a 13A socket outlet.
●This appliance conforms to EC directive 2004/108/EC on Electromagnetic Compatibility and EC regulation no. 1935/2004 of 27/10/2004 on materials intended for contact with food.
key
blender
blade assembly
filler cap
lid
a)plastic = locking lid
b)glass = push fit
goblet
sealing ring
blade assembly
power unit
speed control + pulse mill (if supplied)
mill jar
sealing ring (if supplied)
blade assembly (if supplied)
mill lid
Note: A separate blade assembly for the mill will not be supplied with all models, the sealing ring and and blade assembly and are identical and interchangeable.
to use your blender
1Fit the sealing ring into the blade unit - ensuring the seal is located
correctly in the grooved area.
●Leaking will occur if the seal is damaged or incorrectly fitted.
2Screw the blade assembly onto the goblet . Refer to the graphics on
the underside of the blade unit as follows:-
- unlocked position
- locked position
To ensure the blade assembly is fully tightened check that the 
on the goblet aligns with the 
on the blade assembly. The blender will not operate if incorrectly assembled.
3Put your ingredients into the goblet.
4Fit the filler cap to the lid.
a glass goblet - Fit the lid by pushing down until secure.
b plastic goblet - Fit the lid onto the goblet and turn clockwise until it clicks.
5Place the blender onto the power
unit and turn clockwise until it clicks .
3
Loading...