GE PSW26SGRBSS, PSW23PSRASS, PSS29NGPAWW, PSS29NGPACC, PSS29NGPABB Owner’s Manual

...

0 (0)

°v,,,q

vvvvvv.GEAppliances.com

Safety Instructions ........... 2-4

Operating Instructions

Automatic Icemaker ........... 14

Care and Cleaning .......... 16, 17

Crispers and Pans ............. 13

CustomCool r'*. ............... 7, 8

Ice and _A'ater Dispenser ........ 15

Refligerator Doors ............ 12

Replacing the Light Bulbs ....... 18

Shelves and Bins ........... 10, 11

Temperature Controls ........... 5

TurboCooF _ ................... 6

_A'ater Fiher . .................. 9

Installation Instructions

Installing the Refligerator . . . .98-31 Moving the Refligeramr . .... 24-27 Preparing to Install

the Refligerator . .............. 93

Trim Kits and Panels ........ 19-92

Wamr Line Installation ...... 39-34

Models23,25,26,27 and29

ProfileC6te fiC6te

Rdfrigdrateurs

La section fran_aise commence a la page 46

Profile Lado a Lado

Refrigeradores

Troubleshooting Tips ....... 36-38

Normal Operating Sounds ...... 35

Consumer Support

Consumer Support ..... Back Cover

Performance Data Sheet ........ 41

Product Registration ........ 43, 44 State of Calitbrnia ¼'ater

Treatment Device Certificate ..... 49

Warranty (Canadian) ........... 39

VVarrantv (U.S.) ............... 40

Write the model and serial numbers here:

Model #

Serial #

La secci6n en espa#ol empieza en /a pagina 88

Find these numbers on a label inside the refligerator compartment at the top on the right side.

200D2600P023 49-60238-3 11-03Jfl

IMPORTANTSAFETYINFORMATION. READALLINSTRUCTIONSBEFOREUSING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner's Manual.

SAFETYPRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

This refi_igerator must be properly installed and located in accordance with the Installation

Instructions before it is used.

Do not allow children to climb, st;rod or hang on the shelves in the reti_igerato_: They could

damage the refrigerator and seriously iqjm'e themselves.

Do not touch the cold sm_i_ces in the fl'eezer compartment when hands are damp or wet. Skin

may stick to these extremely cold sudaces.

Do not store or use gasoline or other flammable \:q)o_s and liquids in the vicini F ot this or any other appliance.

In refl_igerato_ with automatic icemake_,

avoid contact with the moving parts of the ejector mechanism, or with the heating element

located on the bottom oI the icemake_; Do not place finge_ or hands on the automatic

icemaking mechanism while the refl]gerator is plugged in.

Keep finget_ out ot the "pinch point" areas; clearances between the doo_ and between

the doo_ and cabinet are necessarily small. Be caretul closing doo_ when children are

in the area.

Unplug the refl_igerator before cleaning and

making repai_.

NOTE."Westronglyrecommendthatany servicingbe performedby aqualified individual

Setting either or both controls to 0 (off) does not remove power to the light circuit.

Do not refl'eeze frozen foods which have thawed completel>

_ Mwa_:s clean the CustomCooY_Tray after thawing

fi_od.

DANGER!RISKOFCHILDENTRAPMENT

PROPERDISPOSALOFTHEREFRIGERATOR

GEAppliances.com

Child entrapment and suffocation are not i)rol)lems of the past.Junked or abandoned refl_igeratm_ are

still dangerous...even if they will sit for "just a few days." If you are getting rid of yore" old refrigerator,

please follow the instructions below to help prevent accidents.

Before YouThrowAway YourOldRefrigerator

Refrigerants

M1 refl_igeration prodtu'ts contnin refl'igerants, which trader federal law must be removed prior to product disposal. If wm are getting rid of an

old refrigeration product, check with the company handling the disposal about what

1() do.

or Freezer:

Take off the dome.

I,eave the shelxes in place so that children max not easilx climb inside.

USEOFEXTENSIONCORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.

However; ifxou must use an extension cord, it is absolutely necessary that it be a Ui,-listed (in the United States) or a (;SA-listed (in Canada), B-wire grotmding type appliance extension cord haxing a grotmding

type i)lug and outlet and that the electrical rating of the cord be 15 amperes (minimmn) and 12(1 xolts.

IMPORTANTSAFETYINFORMATION. READALLINSTRUCTIONSBEFOREUSING.

WARNING!

HOWTOCONNECTELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For

personal safety this appflance must be properly grounded.

Tile power cord of this appliance is equipped

with a 3-prong (grounding) plug which mates with a stnndard 3-prong (grotmding) wall outlet

to minimize tile possibility of electric shock hazard from this appliance.

Have tile wall outlet and circuit checked by a qualNed electridan to make sure tile outlet is

propedy grotmded.

If tile outlet is a standard 2-prong outlet, it is gmr personal responsibility and obligation to have it

replaced with a propedy grotmded %prong wall outlet.

Tile refl-igerator should always be phlgged into its own individual electrical outlet which has a _oltage rating that matches tile rating plate.

This provides tile best pedimnance and also I_rexents oxerloading, house wiring circuits which

could cause a fire hazard fl'om oxerheated wires.

Never tmi_lug your, refl'igerator, bx, I)tilling, on tile power cord. Mways grip ph/g firefly and pull straight

out fl'om tile outlet.

Repair or replace immediately all power cords that have become fl'aved or otherwise damaged. Do not

use a cord that sho_:s cracks or abrasion damage along its length or at either end.

\4lien moving tile reflJgerator away fl'oin tile wall, be carefld not to roll over or damage tile power cord.

USEOFADAPTERPLUGS(Ad_pterplug_notpermittedinco_odo)

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an adapter plug.

However; if'you, must use an adapter; where local codes pemfit, a temporary connection may be made

to a properly grotmded 2-prong wall outlet by use of a UI Aisted adapter a\:lilable at most local

1/_1 I'(1W_lI'e stores.

Tile linger slot in tile adapter must be aligned with tile larger slot in tile wall outlet to provide proper

polarity in tile com_ection of tile power cord.

When disconnecting tile power cord ti'om tile

adapte_; alwa):s hold tile adaI)ter in place with one hand while pulling tile power cord i)lug with tile other hand. If this is not done, tile adapter gromM

temfinal is very likely to break with repeated use.

If the adapter grotmd temfinal breaLs, DO NOT

USEthe refrigerator tmtil a proper grotmd has

been established.

Attaching the adapter ground terminal to a wall outlet cover screw does not ground the appliance unless the

cover screw is metal, and not ihsu/ated, and the waft outlet is grounded through the house wiring. Youshould

have the circuit checked by a qualified electric&n to make sure the outlet is properly grounded

READANDFOLLOWTHISSAFETYINFORMATIONCAREFULLY.

SAVETHESEINSTRUCTIONS

Aboutthe temperaturecontrols. GEAppliances.com

The temperature controls are preset in the factory at 37°1:for the

refrigerator compartment and O°Ffor the freezer compartment. Allow

24 hours for the temperature to stabilize to the preset recommended

settings.

The temperature controls can display both the SET temperature

as well as the actual temperature in the refrigerator and freezer.

The actual temperature may vary slightly from the SETtemperature

based on usage and operating environment. Setting either or both controls to OFFstops cooling in both the freezer

and refrigerator compartments, but does not shut off electrical power to the refrigerator.

temperature controls. If this film was not removed during installation, remove it now.

NOTE: The refrigerator is shipped with protective film covering the

Tochange the temperature, press and release the WARMER or COLDERpad. Tile SETlight will come

on and tile display will show tile set temI)eratm'e. To change tile temperatm'e, tap either tile

WARMER or COLDERpad until tile desired

temperatm'e is displayed. Refl'igerator temperatm'es can be ac!justed between 34°F and 44°F and tile

fl'eezer temperatm'es can be ac!iusted between

-6°F and +6°E

Once tile desired temperature has been set, tile temperatm'e display will retm'n to tile actual

refl-igerator and fl'eezer temperatm'es after 5 seconds. Several ac!iusnnents may be required.

Each time you a(!itlSt controls, allow 24 hotli's t0I" tile refl-igerator to reach tile temperatm'e you have set.

Toturn thecooling system off,tap tile WARMER pad

for either tile refl-igerator or tile fl'eezer tmtil tile display shows OFF. To turn the unit back on, press tile

COLDERpad fin" either tile refrigerator or fl'eeze_:

The SETlight will illuminate on the side w)u selected. Then press the COLDERpad again (on the

side where the SErlight is illuminated) and it will go to tile preset points of O°Ftor tile fl'eezer and

37°ElOr tile refl-igerato_: Setting either or both controls to OFFstops cooling in both the fl'eezer

and refrigerator compartments, but does not shut off electrical power to tile refl-igerato_:

PerformanceAk FlowSystem

Tile Perl0mmnce M>Flow System is designed to maximize temperature control in tile refrigerator

and fl'eezer comparmlents. This unique special teatm'e consists _ff tile Mr Tower along tile back

wall of tile refrigerator and tile Mr Tmmel on tile

bottom portion of tile fl'eezer rear wall. Placing fi_od in fl'ont ot tile louvers on these components will not

affect pe_fommnce. Mthough tile Mr Tower and tile ?dr Tmmel can be removed, doing so will affect

temperatm'e pedomlance. (For removal instructions, on-line, 24 horn's a da> contact us at

GEAl)pliances.com or call 800.GE.CARES. In Canada, contact us at geappliances.ca or call

1.800.361.3400.)

AboutTurboCooLTM

How it Works

TurboCool rapidly cools the retiigerator

compartment in order to more quickly cool fl_ods. Use TurboCoolwhen adding a

TurboCool

large amount of food to the refligerator compartment, putting away fi)ods after they

have been sitting out at room temperature or when putting away warn/lettove_. It can

also be used if the refl_igerator has been

without power tot an extended period.

Once acti\:_md, the compressor will turn oil immediately and the rims will cycle on and off at high speed as needed fiw eight hom_.

The compressor will continue to run until the refligerator compartment cools to

approximately 34°F (1 °C), then it will cycle on and off to maintain this setting. Mter 8

hom_, or if TurboCoolis pressed again, the refl_igerator compartment will return to

the original setting.

How to Use

Press TurboCooL The refrigerator temperature display Mll show ]'C.

_Mter TurboCoo/is complete, the

refl_igerator compartment will return to the original setting.

NOTES:The refligerator temperatm'e

cannot be changed dining

TurboCooL

The fl'eezer temperatm'e is not affected during TurboCooL

_41_en opening the refrigerator door (hmng TurboCool,the tiros

will continue to run if they have

cycled on.

AboutCustomCooU CEApplia,ces.com

• SET ExpressThaw ExpressChi/I SelectTemp

How it Works

Tile CustomCoolTMfeature is a system ot daml)e_, a tim, a temperature themfistor

and a heatex: Depending on tile fimction selected, a combination oI these will be

used to quickly chill items, thaw items or hold tile pan at a specific temperature.

Tile pan is tightly sealed to prevent tile pan's temperature ti'om causing temperature

fluctuations in tile rest of tile reli_igeratm: The controls for this pan are located at the

top of tile reti_igerator with tile temperatm'e

controls.

ExpressThaw_

ExpressChillT"

How to Use

O EmpF tile pan. Place tile (3hill/Thaw

tray in tile pan. Place tile items on tile

tray and close tile pan completel>

@ Select tile Expressrhawj _ExpressChilF_

or SelectTemp_ pad. The display and

SErlight will come on. Tap tile pad until the light appeax_ next to the

desired setting. Use the chart to detemfine tile best setting to use.

To stop a teatm'e before it is finished, tap that teatm'e's pad

tmtil no options are selected and

the display is off. During ExpressThawTM and

ExpressChilE_tile displa_ on tile

controls will co/rot down tile time in the cycle.

How to Remove and Replace the Drawer

Toremove:

Pull tile drawer out to tile stop position.

i,ift tile fl'ont of the drawer up and out

of the wire holder:

O I,ifl tile back of tile drawer up and out.

_Mter tile ExpressThaw _ cycle is

complete, tile pan will reset to tile ME/ITsetting (31°F) to hel I) preserve

thawed items tmtil tile)' are used.

Tile displayed actual temperatm'e of

the CustomCoolpan may _mT slightly

ti'om tile SETtemperamre based on

usage and operating enviromnent.

NOTE"For food safety reasons, it is recommended that foods be wral)ped in plastic wrap when using ExpressThawY

This will help contain meat juices and

improve thawing pe_fimnance.

Toreplace:

Place the back ot the drawer in the wire

holdex; making sure the wire holder

fits into the grooves on the back ot

tile pan.

@ i,ower tile ti'ont (ff tile drawer into tile

wire holder:

Popwire into groove

0 Pull tile bottom of tile wire holder

fi)rward tmtil tile wire pops into tile

grooxe located OIT tile bottolll of

tile (h'awe_:

AboutCustomCool7

CustomCoolTM Chart

NOTE: Results may vary depending on packaging, starting temperature and other food traits.

0.5 Lb. (4 hours)

Hambtuger Patties (0.5 lb) h,Mividually _Vrapped

Filet Mignon (0.5 lb)

1.0 Lb. (6 hours)

Chicken Breasts (1.0 lb)

Ground Beef (1.0 lb) Steak (1.0 lb)

2.0 Lbs. (10 hours)

Chicken Breasts (2.0 lbs)

Ground Beef (2.0 lbs) Steak (2.0 lbs)

3.0 Lbs. (12 hours)

Chicken Breasts (3.0 lbs)

Ground Beef (3.0 lbs) Steak (3.0 lbs)

15 Minutes

1 Beverage Can (12 oz) 2 Small,Juice Boxes (6-8 oz each)

30 Minutes

2 to 6 Beverage Cans (12 oz each)

2 Plastic 20 oz Bottles of Beverage 4 to 6 Small,Juice Boxes

(C_8 oz each)

3 Foil Juice Packets Wine (750 ml bottle)

45 Minutes

2 I,iter of Beverage 1/2 Gallon of, Juice

Gelatin-1 package

Citrus Setting (43°F)

Oranges, I,emons, I,imes, Pineapple, Cantah)upe

Beans, (_tlCtlillbelN, Tomatoes,

Peppe_, Eggplant, Squash

Produce Setting (35°F)

Strawberries, Raspberries, Kiwifl'tfit, Pea_s, Cherries, Blackberries,

Grapes, Plums, Nectarines, Apples _sparagus, Broccoli, Corn,

Mushrooms, Spinach, Cauliflower; I¢ade,Green Onion, Beets, Onions

Meat Setting (31°F)

Raw Meat, Fish and Poultry

Aboutthe water filter.(onsomemodels) GEAppliances.com

Cartridge

HOlder

Place flTetop of flTecartridge up inside the cartridge holder and

slowly turn it to the right.

RESETWATERFILTER

HOLD3SECS

Water Filter Cartridge

Yhe water filter cartridge is located in the

back Iq_per fight corner of tile l'eflJgel'ator

COil/l);I I'tlllent.

When to Replace the Filter

Yhere is a l'eplacelnent indicator light tot

the water filter Cal'tridge oI] the dispel]sel:

Yhis light will tm'n orange to tell you that w)u need to replace the filter soon.

Yhe filter cartridge should be replaced

when the replacement indicator light turns

red o1" if the flow of water to the dispenser

or i(-eI[laker decreases.

Installing the Filter Cartridge

0 If you are re )lacino the cartridge, ti_t

remo',e the old one by slowl} tm'ning it to the left. Do net pull d_)wn on the

cartridge. A small amount ot water may drip down.

_Fill the replacement cartridge with

water ti'om the tap to allow fbr better flow fl'om the dispenser immediately

after installation.

IJning up the arrow on the cartridge

and the cartridge holder; place the top of the new cartridge up inside

the holder; Do not push it up into the holder;

0 Run water fl'om the dispenser fbr

3 mimKes (about 1½ gallons) to clear the s)_stem and prevent sputtering.

0 Press and hold the RESETWATERFILTER

pad on the dispenser for 3 see(rods.

NOTE" A newEqnstalled wamr filmr cartridge may cause water to spurt flom

the dispense_:

Filter Bypass Plug

Y()u must use the filter bypass plug when a replacement filter cartridge is not

available. The dispenser and the icemaker

will not operate without the filter or filter

bypass plug.

Replacement Filters:

To order additional filter cartridges

in _e United States, visit our Website,

GEAppliances.cem,or call

GE Parts and Accessories, 800.626.2002.

Suggested Retail $34.95 USD Customers in Canada should consult

the yellow pages tot the nearest Camco Service Center:

Slowly mrn it to the right m]til the filter cartridge stops. DO NOTOVERTIGHTEN.

_s v(>u mrn the cartridge, it will automatically raise itself into position.

Cartridge will rotate about 1/4 turn.

Abouttheshelvesandbins.

Not all features are on all models.

Refrigerator Door Bins and Freezer Door Tilt-Out Bins

Large Bins

The larger reti-igerator door bins and freezer tilt-out door bins are ac!justable.

Toremove: lift the ti'ont of the bin straight

up, then lift up and out.

Refrigeratorbin

Freezer tilt-out bin

Toreplace or relecate: Engage the back side

of the bin in the molded supports on the

(loo_: Then push down on the front of the bin. Bin will lock in place.

Small Bins

Toremove: i,ifi the fi'ont of the bin strai,,ht

up then out.

Toreplace: Position the bin abo_e the

rectangular molded supports on the doo_:

Then slide the bin down onto the support

to lock it in place.

Thesnuggerhelps prevent tipping, spilling

or sliding of small items stored on the door shelf. Place a finger on either side of the

snugger near the rear and move it back and forth to fit your needs.

Donotblock

CAUTION:Be

carefulwhenplaclbg itemsinthetopbin.

Makesurethat itemsdonotblock orfaillbtotheice

chute.

Topfreezer bin

Press tab and pull shelf forward to remove

Slide-Out Spillproof Shelf

The slide-out spillproof shelf a11o_:s you to reach items stored behind othe_s. The

spedal edges are designed to hel I) prevent spills ti'om dripping to lower shelves.

Toremove:

Slide the shelf out until it reaches the stop,

then press down on the tab and slide the shelf straight out.

Toreplace or relocate:

I,ine the shelf up with the supports and slide it into place. The shelf can be

repositioned when the door is at 90 ° or

more. To reposition the shelf, slide the shelf past the stops and angle downward. Slide shelf down to the desired position, line up

with the supports and slide into place.

Make sure you push the shelvesall the way back in before you close the door.

OuickSpace TM Sheff

This shelf splits in half and slides under itself for storage _ff tall items on the shelf

below.

On some models, this shelf cannot be used in the lowest position.

This shelf can be removed and replaced

or relocatedj ust like Slide-Out Spillproof Shelves.

Not all features are on all models.

Freezer Baskets

Toremove, push the basket all the way to the

back of the fl'eeze_: i,ifl (II) until the back pins are disengaged. I,ifl the entire basket

up and pull out.

GEAppliances.com

Makesureyoupushthebasketsall the wayback in beforeyouclosethe door

(i; ¸ : (:)/ j

(

Sfide-Out Freezer Shelves

Toremove, slide out to the stop position,

lift the front past the stop position and slide out.

Fixed Freezer Shelves

There are two types of fixed

fl'eezer shelves.

Toremove this type ofshelf"

O I,itt the shelf tlI) at the left side.

Bring the shelf otlt.

Toremove this type of shelf"

i,itt tlI) the left side of the shelf and slide it left into the center of the shelf

SUl)ports.

@ Rotate the right side of the shelf tlI)

and out of the shelf supports.

Makesureyoupushtheshelvesall the wayback in beforeyouclosethe door

NOTE FORDISPENSER MODEL& Ill order to take fllll a(h'ant;ige of the flit-out ice bin,

only store items on tile shelf below the ice bin that are no taller than the lowest point

on the bin.

Door Wine/Beverage Rack (onsomemodels)

This rack holds tlI) to 5 cans, one botde of Mne or one 2-liter bottle of soda.

The rack hangs from the sides of the dairx bin.

Toremove:

Emp_ the wine/bmerage rack.

_ Holcling the bottonl of the dairy bin

• . ,y

hft the fi'(mt strmght up, then lilt tlI)

and Otlt.

_To detach the rack fi'om the (laiI_' bin

pull the racks side wires out of the holes on each side of the dairy bin.

Toreplace:

Reattach the rack to the sides of the bin.

Engage the 1)ack side of the bin ill the molded SUl)ports on the do(n:

Then push down on the fi'ont of the

1)in. Tile bin will lock into I)lace.

Abouttherefrigeratordoors.

iii

_ iii i

When the door is only partially open,

it will automatically close. Beyond flTisstop flTedoor will stay open.

Refrigerator Doors

Tile reti_igerator (loo_ may teel different than the ones you are used to. The special

door opening/closing teatuI'e nlakes sure tile/loo_ close all tile way and are securely

sealed.

When opening and closing tile door you will notice a stop position. If tile door is

opened past this stop point, tile door will i'elllain open to allow VOtl to load and

/mh)ad fi)od more easily. When the door is only partially open, it will automatically

close.

Door Alignment

1t (h)o_ are tmexen, a(!iust tile retrigerator (h)o_:

LTsing a 7/16" socket wrench, turn tile

door a(!iusting screw to the right to raise tile doo_; to tile left to lower it.

(A nflon I)lug, imbedded in tile

threads _ffthe pin, prevents the pin ti'om turning unless a wrench is used.)

Tile resistance you ti_el at tile stop position will be reduced as tile door

is loaded with fi)od.

AJier one or two ttlrns of the wI'ench,

oI)en..... and close the refrigerator, door

and check the alignment at the top of

tile dooiN.

Toremovetbebase

grille,opentbedoers, removethescrewat

eachendoftbebase grilleandthenpul[

tbegrillestraightout.

Aboutthe crispersandpans. GEAppliances.com

Not all features are on all models.

Fruit and Vegetable Crispers

Excess water that Inav acculnulate ill the bottom of the (h'awe_ should be wiped (h_':

On some models, the bottom drawer has

lull extension slides that allow flfll access

to the drawei:

i_ii_i!_

HI _ LO

Adjustable Humidity Crispers

Slide the control all the way to the HIsetting

to provide high hulnidi_; recolnlnended fin" most vegetables.

Convertible Meat Pan

The convertible ineat pan has its own cold air duct to allow a sti'ealn of cold air fl'om

the fl'eezer colnl)artment to flow to the pan.

The variable temperature control regulates

the air flow ti'oln the (_lilnate KeepeI:

Aboutcrisperremoval

Slide the control all the way to the LO settin,,_ to proxide lower hulnidi_' lexels

i'ecolnlnellded fi)i" most fl'uits.

Set the control to the coldest setting to store fl'esh ineats.

Set the control to coldto convert the pan to hernial refl_igerator telnl)erature and

provide extra vegetable storage space. The cold air duct is turned ofl_ ¼_riable settings

between these extrelnes can be selected.

Not all features are on all models.

Crisper Removal

Crispei_ can easily be removed by pulling

tile drawer straight out and lifting the drawer up and over the stop location.

If the door l)revents you fl'oln taking out the (h'awei_, fiI_t ti T to remove the door

bins. If this does not offer enough clearance, the refrigerator will need to

be rolled torward until the door opens enough to slide the drawei_ ()tit. In soine

cases, when you roll the refl_igerator ()tit,

you will need to inove the reflJgerator

to the left or right as you roll it ()tit.

Abouttheautomaticicemaker.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Automatic Icemaker

On dispenser models,

to access ice or reach the power switch:

o Lift thebin, then pull it

forward until the bin stops.

Lower the bin to access ice or reach the power switch.

NOTE:In order to take full advantage of the tilt-out ice bin, only store items

on the shelf below the ice bin that are no taller than the Iowest point

on the bhT.

The icemaker will produce seven cubes per cycle---aI)I)roMmately ] 00-130 cubes in a 94-hem" period, depending on fl'eezer

COilli)ai'tulent teilll)ei'attH'e _ i'OOill

temperatm'e, nmnber ot door openings and other use conditions.

If the reti_igerator is operated betore the water connect.ion is made to the icemaket;

set the power switch in the 0 (Off)position. When the reti-igerator has been com_ected

to the water suI)I)ly, set the power switch to the I (on) position.

The icemaker will fill with water when it cools to ] 5°F (-10°(7). A newly installed

refi{gemtor may take 12 to 24 hems to begin

making ice cubes. You will hear a buzzing sotmd each time

the icemaker fills with water Throw away the first troy batches of ice to

allow the water line to clea_:

Be sm'e nothing interteres with the sweep of the teeler amL

X'_hen the bin fills to the lexel of the teeler am_, the icemaker will stop producing

ice. It is nom_al fi)r sexeral cubes to be

joined together:

If ice is not t/se(l fl'eqtlenfl}; old ice cubes PowerLight FeelerArm

will become cloudy, taste stale and shrink.

Special note about dispenser models:

Dispenser models have a tilt-out ice bin.

The bin can be tilted out as shown in the illustrations, and it will hold itself up

while you take ice ()tit or ttlFn the icemaker power switch on and off'. Be

sm'e to put the bin back in place before

closing the doo_:

To restore your ice level from an empty bucket stage, the following steps are

recommended:

12 hom_ after the fi_t batch of ice

has fidlen into the bin, dispense 3 to 4 cubes.

@ _MteI"an additional 6 hom_, dispense

3 to 4 cubes again.

These steps will restore your ice level in the shortest amount of time.

]cemaker

Green

NOTE:/n homes with lower-than-averagewater pressure,you mayhear the icemakercycle multiple

times whenmak/bg onebatchof ice.

o Lift thebin,thenpull it

forwarduntilthebinstops.

Lift andpull forward again

to remove the bin.

Removing Ice Bin (dispensermodels)

CAUTlON: The ice bin is heavy when full.

before removing the bin.

When replacing the bin, be sure to press it

fimfl) into place. If it does not go all the wax back remoxe it and rotate the dfixe

thel,o,,e,swit,htotheO l,ositi..

mechanism 1/4 ttlFn. Then push the bin back again.

Dispenser Models only

Aboutthe ice and water dispenser.(onsomemodels) GEAppliances.com

ToUse the Dispenser

i _'

QUICKICE ,

DoorAlarm

This pad turns tile night light in tile dispenser

on and off. The light

also coi/les on when

tile dispenser cradle is pressed. If this light bm'ns out, it should be

replaced with a 6 watt

12V maximmn bulb.

When you need ice

in a ht_rry, press this pad to speed up ice

production. This will increase ice production

for tile following 48 hours or tmtil you press the pad again.

SpillShelf

Select CUBED ICE ,__:_"CRUSHEDICE I_ DispenserLight

WATER

Press the glass gentl} against the top ot

the dispenser cradle. Tile spill shelf is not selfkh'aining.

To reduce water s )otting, tile shelf and LIGHT its grille should be cleaned regularly.

If no water is dispensed when the refngeretor is

first instafled, there may be air in the water line

system. Pressthe dispenser arm for at least two Quick Ice

minutes to remove trapped air from the water

fine and to fill the water system. Toflush out ..............................................................

impurities in the waterline, throwaway the first ..........................................................

six glassfuls of water

CAUTION: Never put fingers or any other

objects into the ice crusher discharge opening.

I,_7-

Lockingthe Dispenser

• Press the LOCKCONTROL

pad fin 3 seconds to

,o kco..olt"ep..eldispe.se,To..d

mflock, press and

LOCKCONTROL hold the pad again

HOLD3 SECS

Important Facts About Your Dispenser

Do not add ice Ii'om trays or bags to tile storage drawer It may not crush or

dispense well.

Avoid overfilling glass with ice and use of

narrow glasses. Backed-up ice can jam the chute or cause tile door in tile chute to

fl'eeze shut. If ice is blocking the chute, poke it through with a wooden spoon.

Beverages and ti)()(ls should not be quick-chilled in the ice storage drawen

Cans, bottles or food packages in the

storage dI'aWeI" Ill,IV catlse tile icemaker

or auger to jain.

To keep dispensed ice ti'om missing the glass, put the glass close to, but not

touching, the dispenser opening.

for 3 seconds.

DOOR ALARM

Some crushed ice may be dispensed even though you selected CUBEDICE.

This happens occasionally when a fi_w cubes acddentally get directed to

tile crusher.

_Mier crushed ice is dispensed, some

water may drip ti'om tile chute.

Sometimes a small mo/md of snow will form on tile door in tile ice chute. This

condition is n(mnal and usually occtli's

when you have dispensed crushed ice

repeatedly. The snow will evenmalh' evapoi'ate.

To set tile alamo, press this pad tmtil tile

indicator light comes

on. This alam_ will solmd il either door is

open JOi" I//oI'e than

3 minutes. The light goes out and the beeping stops when

you close the (loon

Careand cleaning of the refrigerator.

Cleaning the Outside

The dispenser drip area, beneath tile giille,

should be _ped dIT: _,\_ter left in this area may lea',e deposits. Remo',e the deposits by

Dispenser drip area.

adding undiluted vinegar to the well. Soak

until tile deposits disappear or become

loose enotlgh to iJnse _l_';iv.

The dispenser cradle. Before cleaning, lock

tile dispenser by pressing and holding tile LOCKCONTROLpad tot 3 seconds. Clean

with wam_ water and baking soda solution--about a tnblespoon (15 ml) of

baking soda to a quart (l liter) of wateI:

Rinse thoroughly and wipe dry.

The deer handles and trim. Clean with

a cloth dampened with soapy wateI:

Dry with a soft cloth.

The stainless steel panels and door handles

(oil sonle models) can be cleaned with a commercially a\:filable stainless steel cleanei: A spra)_on stainless steel cleaner

works best.

Do not use appliance wax or polish on the stainless steel,

Keep theoutsideclean.Wipe Mth a clean cloth lightly dampened Mth kitchen

appliance wax or mild liquid dish detergent. Dry and polish with a clean, soft cloth.

Donot wipethe refrigeratorwith a soileddish cloth orwet towel.Thesemayleavearesidue

thatcanerodethepainLDonotusescouring pads,powderedcleaners,bleachorcleaners

containingbleachbecausetheseproductscan scratchandweakenthepaint finish.

Cleaning the Inside

Tohelp prevent odors, leave an open bc,x ,':4

baking soda in tile fl'esh ti)od and fl'eezer

COII/l)_l i'tiilents.

Unplug the refrigerator before cleaning. If this

is not practical, wiing excess moisture ()/It

of sponge or cloth when cleaning around

switches, lights or controls.

Lrse w;mn wamr and baking soda solution--

about a tablespoon (15 ml) of baking soda

to a quart (1 liter) (ff wami: This both cleans and neutralizes odois, Rinse and

wipe dry:

Useofanycleaningsolutionotherthanthat

which isrecommended,especiallythosethat

containpetroleumdistillates,can crackor damagethe interioroftherefrigerator.

Avoidcleaningcoldglassshelveswith hotwater becausethe extremetemperaturedifference

maycausethemtobreak.Handleglassshelves carefuflgBumpingtemperedglasscancause

it to shatter Donot washanyplastic refngeratorparts

in thedishwasher

Thechili/thawtrayis dishwashersafe.

Behind the Refrigerator

Be careful when moving the refl_igerator away fl'om the wall. _dl types of floor

coverings can be damaged, particularly cushioned coverings and those with

enlbossed S/li]_lces.

Pull the refl_igerator straight out and return it m position by pushing it straight in.

Moving the refl_igerator in a side direction may result in damage to the floor covering

or refl_igerato_:

Preparing for Vacation

For long ;;ications or absences, YelllOve

food and uI_plug the refl_igerato_: Clean the interior with a baking soda solution of one

tablespoon (15 ml) of baking soda to one quart (l liter) of water: i,eave the (loo_

open.

Set the icemaker power switch to the 0 (off) position and shut off the water supply to

the refl_igeratm:

GEAppliances.com

When pushing the refrigerator back, make sure

you don't roll over the power cord or icemaker

supply line.

If the temperatm'e can drop below fl'eezing, have a qualified servicer drain the water

supply s)'stem to prevent serious property damage due to flooding.

Preparing to Move

Secure all loose items such as shelves and (h'awe_ by taping them securely in place

to prevent damage.

X4]_en using a hand track to move the

refl_igeratot; do not rest the fl'ont or back _ffthe reti_igerator against the hand truck.

This could damage the refrigerator. Handle only fl'om the sides of the refl_igeratm:

Be sure the refn)erator stays in an upn)ht position during moving.

Replacingthelightbulbs.

Setting the controls to OFFdoes not remove power to the light circuit.

Refrigerator Compartment--Upper Light

Tabs

Unplug the refl'igerator.

The bulbs are located at the top ot the

compartment, inside the light shield. On some models, a screw at the fl'ont of

the light shield will have to be removed.

To remoxe the light shield, press in on

the tabs on the sides of the shield and slide fin'ward and out.

Refrigerator Compartment--Lower Light

This hght is located above the top drawe_

O Unplug the refligerato_:

0 Remo'_e the comertible meat drawer

control knob b) pulling straight out.

lift the light shield up and pull it out.

Freezer Compartment

O _Mier repladng the bulb with an

appliance bulb of the same or lower wattage, replace the light shield and screws (on some models). When

replacing the light shield, make sure that the tabs at the back ot the shield

fit into the slots at the back of the light shield housing.

Plug the refl_igerator back in.

@ _Mter replacing the bulb xfith an

appliance bulb of the same c,r lower wattage, replace the shield and

the knob.

Plug the refrigerator back in.

O Unplug the refligeraun: O Remoxe the shelfjtlst aboxe the light

shield. (The shelf will be easier to remoxe if it is emptied fi_t.) On some models, a screw at the top of the light

shield will need to be remoxed.

To remoxe the light shield, press in on the sides, and lift up and out.

Dispenser

Unplug the refl_igeratox: The bulb is located on the dispenser

trader the control panel.

Remove the light bulb by turning it counterclockwise.

Replace the bull) with an appliance

bulb of the same or lower wattage, and reinstall the light shield. When

reinstalling the light shield, make sure the top tabs snap securely

into place. Replace the screw

(on some Inodels).

Reinstall the shelf and plug the refrigerator back in.

O Replace the bulb with a bulb of the

SaIlle size aIld watta(*e

Plug the refrigerator back in.

Trimkits anddecoratorpanels.

For CustomStgM°'models

Read theseinstructions completely and carefully.

BeforeYouBegin

Some models are equipped with trim kits that aflow you to install door panels. You can order pre-cut black, white, bisque or stainless steel decorator panels from GE Parts and Accessories,

800.626.2002,or you can add wood panels to match your kitchen cabinets.

Panels less than 1/4" (6 mm) thick

When installing wood panels less than ]/4" (6 ram) thick, you need to create a filler panel, such as ]/8"

cardboard, that Mll fit between the ti_ce of the door and the wood panel. If you are installing the pre-cut decorator panels, pre-cut filler panels are included in the kit. The coml)ined thickness of the decorator

or wood panel and the filler panel should be 1/4" (6 ram).

PanelsI/4" thickorless

1/4"max

3/4" (19 mm) or Raised Panel

A raised panel design screwed or glued to a 1/4" (6 ram) thick backing, or a ./4 (19 ram) routed board can be used. The raised portion of the panel must be tid)ricated to i)ennit clearances of at least _2" (5. l cm)

from the handle side tot fingertip clearance.

•/4 (l 9 ram) max, xdll require that the outer :5/16" (8 ram) ofPanels thicker than 1/4" (6 ram), uI) to 3 "

panel perimeter be no thicker than 1/4" (6 ram).

Weightlimitationsfor custompanels."

FreshFood38Ibs. (17kg)max. FreezerDoor28Ibs. (13kg)max.

Panelsthickerthan1/4"(6ram)

1/4" (6ITllrl)max

3/4" (19ram) Panel tor

Appeara,,c _]l

1/4"(6ram)

ThickBacking

Door

Trimkits anddecoratorpanels.

Dimensions for Custom Wood Panels

FreezerPanel

WithoutDispenser

Cut 1/8" out "-_I _.-(3mm)

__iii I I

5/16"

(Smm}

67_2" (170.gcm)

FRONT

4._. 141_Z' i, (36.8cm)

FreezerPanel

WithDispenser

Cut 1/8" out --_f f_'-(3 irlm}

i i

177X' {45.4cm)

FRONT

. 141_Z' .--,

(36.8 cm)

33_" (85.4cm)

{

FreshFoodPanel

1/8" Cut

(3n/m)"-_f f"- out

FRONT

191_2" _..__

(49.5cm)

67%Z'

(170.9cm)

' ' 5/16" I....{ (8ram)

The areas at the top of the panels need to be cut out of the panels.

Insertingthe doorpanels.

Read these instructions completely and carefully.

0 Insert the Freezer Panel and FreshFood Panel

(_arefully push the ti'eezer panel in until it slides If your model has a dispense_; this step only applies into the slot behind the door handle. Push the filler to the fl'esh fi)od panel and top fl'eezer panel.

panel (required with some door panels) in behind the decorator panel. Repeat fin" fl'esh fi_od panel.

0 Insert the Bottom Freezer Panel (on dispenser models).

(_areftfll) push the panel in tmtil it slides into the (reqtfired with some door panels) in behind the slot behind the door handle. Push the filler panel decorator panel.

Attach the TopTrimon the Freezer and Fresh FoodDoors.

The Top Trim can be fi_tmd inside the reii_Jgerator each (loo_: Hand tighten only. Make sm'e that the compartment, top of each panel fits snugly behind the lip of the

_]th a T-20 Torxdrive_; attach the Top Trim, using Top Trim. two scre_:s on each Top Trim piece, to the top oI

Cut-Out

SideTrim

Insertingthe doorpanels.

O Install the Side Trim.

These pieces are tucked inside the reti_gerator door handle.

Donot removetheprotectivefilmon theoutsideof theSideTrimuntil theSideTrimis instated.

Fit the bottom of the Side Trim under the Bottom Trim as illustrated.

Hold the Side Trim against the fl'ont ti_ce of the decorator panels and fit the Side Trim under

the Top Trim. Make sure the magnetically attached Side TYim is fitted correctly and that _m are

satisfied with the appearance of all the parts.

Installation

Refrigerator

Instructions

I Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com

BEFORE YOU BEGIN

Read these instructions completely and carefully.

• IMPORTANT - Savethese

instructions for local inspector's use.

• IMPORTANT - Observeall

governing codes and ordinances.

• Note to Installer - Be sure to leave these instructions with the Consumer.

• Note to Consumer - Keep these instructions for future reference.

• Skill level - Installation of this appliance requires basic mechanical skills.

• Completion time - Refrigerator Installation

• Proper installation is the responsibility of the installer.

In Canada, call 1.800.361.3400 or Visit our Website at: geappliances.ca

30 minutes Water Line Installation

30 minutes

Models 23, 25, 26, 27 & 29

PREPARATION WATER SUPPLY TO THE ICEMAKER

If the refrigerator has an icemaker, it will have

to be connected to a cold water line. A GE water supply kit (containing tubing, shutoff

valve, fittings and instructions) is available at extra cost from your dealer, by visiting our Website at GEAppliances.com (in Canada at geappliances.ca) or from Parts and

Accessories, 800.626.2002 (in Canada

1.888.261.3055).

TOOLS YOU WILL NEED

3/8" and 5/16" Socket 1/2" and 7/16" Wrench

• Product failure due to improper installation is not covered under the Warranty.

If the refrigerator has already been installed, remove the base grille (see Step 2 in Moving

the Refrigerator), then skip to Step 5 in

Installing the Refrigerator.

Plastic Putty Knife

Phillips Head Screwdriver

Installation Instructions

MOVING THE REFRIGERATOR

[] LOADING THE RERIGERATOR

ONTO A HAND TRUCK

Leave all tape and door pads on doors

until the refrigerator is in its final location. To move the refrigerator, use a padded

hand truck. Center the refrigerator on the hand truck and secure the strap around

the refrigerator. DO NOT OVERTIGHTEN

THE STRAP.

If the refrigerator must go through any entrance that is less than 38"

wide, the doors must be removed.

Proceed to Step 3. DO NOT remove the handles.

If all entrances are more than 38" wide, skip to Installing

the Refrigerator.

[] DISCONNECT THE WATER

COUPLING (on some models)

If the refrigerator has a water dispenser, there is a water line from the cabinet into

the bottom hinge on the freezer door that must be disconnected.

To disconnect, push in on the white collar of the coupling and pull out the tubing.

White collar

[] REMOVE THE BASE GRILLE

Remove the grille by removing the two Phillips head screws.

Bottom

freezer

hinge

Installation Instructions

[] DISCONNECT THE POWER

COUPLING (on some models)

If the refrigerator has a water dispenser,

there is a power line (harness) from the

cabinet into the bottom hinge on the freezer door that must be disconnected.

To disconnect pull apart at the coupling.

[] DISCONNECT THE ELECTRICAL

CONNECTORS (on some models)

If the refrigerator has a refreshment center, there are electrical connectors

(harnesses) from the cabinet into the

bottom hinge on the refrigerator door

that must be disconnected.

To disconnect, pull apart each connector.

[] CLOSE THE FREEZER AND

REFRIGERATOR DOORS

[] REMOVE THE FREEZER DOOR

[] Remove the freezer door top hinge cover

by either squeezing it and pulling it up or by prying it off with a plastic putty knife.

Bottom

refrigerator hinge

[] Remove the two 5/16" hex head screws,

then lift the hinge straight up to free the hinge pin. 5/16" hex head

[] Open the freezer door to 90. °

90 °

Installation Instructions

MOVING THE REFRIGERATOR (CONT.)

[]

REMOVE THE

FREEZER DOOR (cont.)

[]

As one person slowly lifts the freezer door up and off the bottom hinge, the second person should carefully guide the water line and power line (harness) through the bottom hinge.

[] REMOVE THE

REFRIGERATOR DOOR (cont.)

[] Remove the two 5/16" hex head screws,

then lift the hinge straight up to free the hinge pin.

[] Open the refrigerator door to 90. °

5/16" hex head

[] Set the door on a non-scratching surface

with the inside up.

[] REMOVE THE

REFRIGERATOR DOOR

[] Remove the refrigerator door top hinge

cover by either squeezing it and pulling it up or by prying it off with a plastic putty knife.

_ H

90 °

Installation Instructions

[] REMOVE THE

REFRIGERATOR DOOR (cont.)

[] Lift the refrigerator door up and off the

bottom hinge. If the refrigerator has a refreshment

center, one person should slowly lift the door up and off the bottom hinge and the second person should carefully guide the electrical lines (harnesses) through the bottom hinge.

[] REPLACING THE DOORS

To replace the doors, simply reverse steps 3 through 8.

However, please note the following:

* When lowering the doors onto the

bottom hinges, make sure the second person carefully guides the tube and harnesses through the holes in the hinges.

• When connecting the water line, make sure you insert the tubing all the way

to the mark.

Refreshment Center Models Only

[] Set the door on a non-scratching surface

with the inside up.

Mark

• Do not pinch the tubing and harnesses

when placing the doors on the bottom

hinges.

• When connecting the power line and

the electrical lines (refreshment center

models only), be sure that the

connectors are seated together fully.

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

• Do not install the refrigerator where the temperature will go below 60°F (16°C)

because it will not run often enough to maintain proper temperatures.

• Do not install the refrigerator where the temperature will go above 100°F (37°C)

because it will not perform properly.

• Install it on a floor strong enough to

support it fully loaded.

CLEARANCES

Allow the following clearances for ease of installation, proper air circulation and plumbing and electrical connections:

23' 25/26/27' and 29'

Sides 1/8" (4 mm) 1/8" (4 mm) Top 1" (25 mm) 1" (25 mm)

Back 1/2" (13 mm) 1" (25 mm)

DIMENSIONS AND SPECIFICATIONS

(for CustomStyle TM models)

70¼"(178.4cm

91.4cm)

Water Electrical

24"(61 cm)

Cabinet

/4" (19ram)Airspace

(1/2"[13lem]Gap+

1/4" [6mm]WallPlates)

25" (63.5cm} Countertop

Installation Instructions

[] CONNECTING THE REFRIGERATOR

TO THE HOUSE WATER LINE (icemaker and dispenser models)

A cold water supply is required for automatic icemaker and dispenser operation. If there is not a cold water supply, you will need to provide one. See Installing the Water Line section.

NOTES:

Before making the connection to the refrigerator, be sure the refrigerator power cord is not plugged into the wall

outlet.

• If your refrigerator does not have a water filter, we recommend installing

one if your water supply has sand or particles that could clog the screen of

the refrigerator's water valve. Install it

in the water line near the refrigerator. If using GE SmartConnect TMRefrigerator

Tubing Kit, you will need an additional tube (WX08X10002) to connect the filter.

Do not cut plastic tube to install filter.

[] If you are using copper tubing, place a

compression nut and ferrule (sleeve) onto

the end of the tubing coming from the

house cold water supply.

If you are using the GE SmartConnect TM

tubing, the nuts are already assembled to the tubing.

[] If you are using copper tubing, insert

the end of the tubing into the refrigerator

connection, at the back of the refrigerator, as far as possible. While holding the

tubing, tighten the fitting.

If you are using GE SmartConnect TM

tubing, insert the molded end of the

tubing into the refrigerator connection,

at the back of the refrigerator, and tighten

the compression nut until it is hand tight.

Then tighten one additional turn with a

wrench. Overtightening may cause leaks.

[] Fasten the tubing into the clamp provided

to hold it in position. You may need to pry open the clamp.

Tubing Clamp 1/4" Tubing

1/4"

Compression

Ferrule

(sleeve)

Refrigerator Connection

SmartConnect TMTubing

[] TURN ON THE WATER SUPPLY

Turn the water on at the shutoff valve (house water supply) and check for

any leaks.

[] PLUG IN THE REFRIGERATOR

Before plugging in the refrigerator, make sure the icemaker power switch is set to the 0 (off) position.

See the grounding information attached to the power cord.

Installation Instructions

INSTALLING THE REFRIGERATOR (CONT,)

[] PUT THE REFRIGERATOR

IN PLACE

Move the refrigerator to its final location.

[] LEVEL THE REFRIGERATOR

The refrigerator can be leveled by adjusting the rollers located near the bottom hinges.

_"""""_ Rol Iers

[] LEVEL THE REFRIGERATOR

(cont.)

To adjust the rollers on 23' models:

Turn the front roller adjusting

screws clockwise to raise the

refrigerator,

counterclockwise Roller adjusting screws

to lower it. Use a 3/8" hex socket or wrench, or an adjustable

wrench. These models also have rear adjustable

rollers so you can align the refrigerator with your kitchen cabinets. Use a long-

handled 5/16" socket wrench to turn the screws for the rear rollers--clockwise to

raise the refrigerator, counterclockwise to lower it.

Raise

Rollers have three purposes:

• Rollers adjust so the door closes easily when opened about halfway. (Raise the

front about 5/8" [16 mm] from the floor.)

• Rollers adjust so the refrigerator is firmly positioned on the floor and does

not wobble.

• Rollers allow you to move the

refrigerator away from the wall for

cleaning.

To adjust the rollers on 25/26/27' and 29' models:

adjusting screws

clockwise to --

Tumtheroer I11

raise the -------

counterclockwise

refrigerator, ___

to lower it. Use a

3/8" hex socket _ [] __

or wrench, or an _\ adjustable

wrench. Roller adjusting screw

[] LEVEL THE DOORS

Adjust the refrigerator door to make the doors even at the top.

To align:

[]

Using a 7/16" wrench, turn the door adjusting screw to the right to raise the door, to the left to lower it.

NOTE:

A nylon plug, imbedded in the threads of the pin, prevents the pin from turning

unless a wrench is used.

[]

After one or two turns of the wrench, open and close the refrigerator door and check the alignment at the top of the doors.

Doors should be even at top

+ 102 hidden pages