GE CZS25TSESS, GSCS3PGXSS, GZS23HSESS, GZS23HGEWW, GSCF3PGXBB Owner's Manual

GEAppliances.com

Refrigerators

Side by Side

Safety Instructions . . . . . . . . . . . . . . . . .2–3

Operating Instructions

Automatic Icemaker. . . . . . . . . . . . . . . . . . 12,13

Care and Cleaning . . . . . . . . . . . . . . . . . . . 15,16

Crispers and Pans . . . . . . . . . . . . . . . . . . . . . . .11

ExpressChill™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Ice and Water Dispenser . . . . . . . . . . . . . . . .14

Refrigerator Doors . . . . . . . . . . . . . . . . . . . . . .10

Replacing the Light Bulbs. . . . . . . . . . . . . 16,17

Shelves and Bins . . . . . . . . . . . . . . . . . . . . . . .8, 9

Temperature Controls . . . . . . . . . . . . . . . . . . . . 4

TurboCool™ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

ClimateKepper2 . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Water Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Installation Instructions

Installing the Refrigerator. . . . . . . . . . . . 23–26 Moving the Refrigerator . . . . . . . . . . . . . 19–22 Preparing to Install

the Refrigerator . . . . . . . . . . . . . . . . . . . . . . . . .18 Water Line Installation . . . . . . . . . . . . . . 27–29

Troubleshooting Tips . . . . . . . . . . . . 31–33

Normal Operating Sounds . . . . . . . . . . . . . . .30

Consumer Support

Consumer Support . . . . . . . . . . . . . Back Cover

Performance Data Sheet . . . . . . . . . . . . . 34,35

State of California Water

Treatment Device Certificate. . . . . . . . . . . . .36

Warranty (U.S.) . . . . . . . . . . . . . . . . . . . . . . . . . .37

Warranty (Canadian) . . . . . . . . . . . . . . . . . . . .38

Product Registration (Canadian) . . . . . . . . . 39

Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40

Write the model and serial numbers here:

Model # _________________________

Serial # __________________________

Find these numbers on a label inside the refrigerator compartment at the top on the right side.

Owner’s Manual

and Installation

Models 22, 23, 25,26,27 and 29

Côte à Côte

Réfrigérateurs

Manuel d’utilisation et d’installation

La section française commence à la page 40

Lado a Lado

Refrigeradores

Manual del propietario e instalación

La sección en español empieza en la página 75

200D8074P051 49-60646-2 06-13 GE

IMPORTANT SAFETY INFORMATION.

READ ALL INSTRUCTIONS BEFORE USING.

WARNING!

Use this appliance only for its intended purpose as described in this Owner’s Manual.

SAFETY PRECAUTIONS

When using electrical appliances, basic safety precautions should be followed, including the following:

This refrigerator must be properly installed and located in accordance with the Installation Instructions before it is used.

Do not allow children to climb, stand or hang on the shelves in the refrigerator. They could damage the refrigerator and seriously injure themselves.

Do not touch the cold surfaces in the freezer compartment when hands are damp or wet. Skin may stick to these extremely cold surfaces.

Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

In refrigerators with automatic icemakers, avoid contact with the moving parts of the ejector mechanism, or with the heating element located on the bottom of the icemaker. Do not place fingers or hands on the automatic icemaking mechanism while the refrigerator is plugged in.

Keep fingers out of the “pinch point” areas; clearances between the doors and between the doors and cabinet are necessarily small. Be careful closing doors when children are in the area.

Unplug the refrigerator before cleaning and making repairs.

NOTE: We strongly recommend that any servicing be performed by a qualified individual.

Do not refreeze frozen foods which have thawed completely.

NOTE: Turning the refrigerator off via the controls on the touch panel does not shut off electrical power to the refrigerator.

2

GEAppliances.com

DANGER! RISK OF CHILD ENTRAPMENT

PROPER DISPOSAL OF THE REFRIGERATOR

Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigerators are still dangerous…even if they will sit for “just a few days.” If you are getting rid of your old refrigerator, please follow the instructions below to help prevent accidents.

Before You Throw Away Your Old Refrigerator or Freezer:

Take off the doors.

Leave the shelves in place so that children may not easily climb inside.

Refrigerants

All refrigeration products contain refrigerants, which under federal law must be removed prior to product disposal. If you are getting rid of an old refrigeration product, check with the company handling the disposal about what to do.

USE OF EXTENSION CORDS

Because of potential safety hazards under certain conditions, we strongly recommend against the use of an extension cord.

However, if you must use an extension cord, it is absolutely necessary that it be a UL-listed (in the United States) or a CSA-listed (in Canada), 3-wire grounding type appliance extension cord having a grounding type plug and outlet and that the electrical rating of the cord be 15 amperes (minimum) and 120 volts.

WARNING!

HOW TO CONNECT ELECTRICITY

Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. For personal safety, this appliance must be properly grounded.

The power cord of this appliance is equipped with a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance.

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.

If the outlet is a standard 2-prong outlet, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

The refrigerator should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.

This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.

Never unplug your refrigerator by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet.

Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.

When moving the refrigerator away from the wall, be careful not to roll over or damage the power cord.

READ AND FOLLOW THIS SAFETY INFORMATION CAREFULLY.

SAVE THESE INSTRUCTIONS

3

About the temperature controls.

Not all features are on all models. Your controls may be similar to the following:

OR

The temperature controls are preset in the factory at 37°F for the refrigerator compartment and 0°F for the freezer compartment. Allow 24 hours for the temperature to stabilize to the preset recommended settings.

The temperature controls can display both the SET temperature as well as the actual temperature in the refrigerator and freezer. The actual temperature may vary slightly from the SET temperature based on usage and operating environment.

On some models, setting both controls to the warmest setting until the display flashes (off) will stop cooling in both the freezer and refrigerator compartments.

On other models, setting either control to the warmest setting until the display flashes (off) will stop the cooling to the freezer and refrigerator.

NOTE: Turning the refrigerator off via the controls on the touch panel does not shut off electrical power to the refrigerator.

NOTE: The refrigerator is shipped with protective filmcovering the temperature controls. If this film was not removed during installation, remove it now.

Performance Air Flow System

The Performance Air-Flow System is designed to maximize temperature control in the refrigerator and freezer compartments. This unique special feature consists of the Air Tower along the back wall of the refrigerator and the Air Tunnel on the bottom portion of the freezer rear wall.

Placing food in front of the louvers on these components will not affect performance. Although the Air Tower and the Air Tunnel can be removed, doing so will affect temperature performance. (For removal instructions, on-line, 24 hours a day, contact us at GEAppliances.com or call 800.GE.CARES.

In Canada, contact us at geappliances.ca or call 1.800.561.3344.)

4

About ClimateKeeper2.™ (on some models)

GEAppliances.com

How it Works

The ClimateKeeper2™ is the industry’s most advanced refrigeration system, delivering optimum temperature and humidity performance to keep food garden fresh longer and reduce freezer burn.

The ClimateKeeper2™ system features two

HYDSRUDWRUV³RQH IRU WKH UHIULJHUDWRU DQG RQH for the freezer.

This provides two separate cooling systems, and separates the airflow between the fresh food and freezer compartments during normal cooling operations.*

This ensures that the humidity levels in the fresh food compartment are significantly higher than in a conventional system,** allowing fresh produce and other unsealed foods to retain their moisture content and freshness longer. Moisture sensitive foods such as fresh fruit, salads, rice, etc., can now be stored on open shelves without excessive moisture loss.

Due to the higher humidity in the refrigerator, you may on occasion experience fog or small amounts of moisture in the refrigerator compartment. This is normal and may

come and go as different food loads and environmental conditions change. Wipe dry with a paper towel if desired.

The separate airflow system minimizes the mixing of air between the two compartments, which reduces fresh food odor transfer to improve the taste of ice.

The ClimateKeeper2™ system also reduces the number of defrosting cycles in the freezer evaporator, thereby reducing freezer burn.

*Freezer air is used in the CustomCool™ feature.

**Testing shows a higher level of humidity in the Fresh Food section in ClimateKeeper2™ refrigerators versus conventional units.

About TurboCool.™ (on some models)

How it Works

			TurboCool ™ rapidly cools the refrigerator
			compartment in order to more quickly cool foods.
			Use TurboCool ™ when adding a large amount
			of food to the refrigerator compartment, putting
			away foods after they have been sitting out at room
			temperature or when putting away warm leftovers.
			It can also be used if the refrigerator has been
OR			without power for an extended period.

Once activated, the compressor will turn on immediately and the fans will cycle on and off at high speed as needed for eight hours. The

compressor will continue to run until the refrigerator compartment cools to approximately 34°F (1°C), then it will cycle on and off to maintain this setting. After 8 hours, or if TurboCool ™ is pressed again, the refrigerator compartment will return to the original setting.

How to Use

Press TurboCool.™ The TurboCool ™ temperature display will show Tc and the LED will be activated.

After TurboCool ™ is complete, the TurboCool ™ indicator light will go out.

NOTES: The refrigerator temperature cannot be changed during TurboCool ™.

The freezer temperature is not affected during TurboCool ™.

When opening the refrigerator door during TurboCool ™, the fans will continue to run if they have cycled on.

5

About ExpressChill™. (on some models)

How it Works

The ExpressChill™ feature is a system of dampers, a fan and a temperature thermistor.

The pan is tightly sealed to prevent the pan’s temperature from causing temperature fluctuations in the rest of the refrigerator.

The controls for this pan are located in the top of the refrigerator or on the dispenser with the temperature controls.

	How to Use
	Empty the pan. Place the Chill tray in the
	pan. Place the items on the tray and close
	the pan completely.
	Select the ExpressChill™ pad. On some
	models, you can then select the chill time
	(use chart to determine best setting). Other
ExpressChill™	models will only have one option (45
	minutes). On models with multiple settings,
	tap the pad until the light appears next to

the desired setting.

To stop a feature before it is finished, tap that feature’s pad until no options are selected and the display is off.

During ExpressChill™,the display on the controls will count down the time in the cycle.

How to Remove and Replace the Drawer

To remove:

Pull the drawer out to the stop position.

Rotate all four swing locks to the unlock position.

Lift the front of the drawer up and out.

To replace:

Lock all four swing locks by rotating them to the lock position.

Make sure all four swing locks are in the unlock position.

Place the sides of the drawer into the drawer supports, making sure the swing locks fit on the drawer slots.

ExpressChill™ Chart (on some models)

NOTE: Results may vary depending on packaging, starting temperature and other food traits.

15Minutes

1 Beverage Can (12 oz)

2 Small Juice Boxes (6–8 oz each)

30Minutes

2 to 6 Beverage Cans

(12 oz each)

2 Plastic 20 oz Bottles of Beverage

4 to 6 Small Juice Boxes (6–8 oz each)

45 Minutes

2 Liters of Beverage

1/2 Gallon of Juice

*HODWLQ³ SDFNDJH

3 Foil Juice Packets

Wine (750 ml bottle)

6

About the water filter. (on some models)

GEAppliances.com

Water Filter Cartridge

The water filter cartridge is located in the back upper right corner of the refrigerator compartment.

When to Replace the Filter on Models With a Replacement Indicator Light

There is a replacement indicator light for the water filter cartridge on the dispenser. This light will turn orange to tell you that you need to replace the filter soon.

The filter cartridge should be replaced when the replacement indicator light turns red or if the flow of water to the dispenser or icemaker decreases.

When to Replace the Filter on Models Without a Replacement Indicator Light

The filter cartridge should be replaced every six months or earlier if the flow of water to the water dispenser or icemaker decreases.

Removing the Filter Cartridge

If you are replacing the cartridge, first remove the old one by slowly turning it to the left. Do not pull down on the cartridge. A small amount of water may drip down.

Installing the Filter Cartridge

If you are replacing a SmartWater cartridge with an adapter, it must be removed before installing the cartridge. To remove the adapter, turn it to the left about 1/4 turn.

If you are replacing a Water by Culligan cartridge, leave the adapter in place. This adapter will stay in the refrigerator when you replace future cartridges.

			Some models
	With adapter	Without adapter	use this type of
			water filter.
	(appearance may vary)

On models ithout a replacement indicator light, apply the month and year sticker to the new cartridge to remind you to replace the filter in six months.

Fill the replacement cartridge with water from the tap to allow for better flow from the dispenser immediately after installation.

Line up the arrow on the cartridge and the cartridge holder. Place the top of the new cartridge up inside the holder. Do not push it up into the holder.

Slowly turn it to the right until the filter cartridge stops. DO NOT OVERTIGHTEN. As you turn the cartridge, it will automatically raise itself into position. The cartridge will move about 1/2 turn.

Cartridge

Holder

Run water from the dispenser 1-1/2 gallons (about three minutes) to clear the system and prevent sputtering.

Press and hold the WATER FILTER pad (on some models) on the dispenser for 3 seconds.

NOTE: A newly-installed water filter cartridge may cause water to spurt from the dispenser upon first use.

Filter Bypass Plug

You must use the filter bypass plug when a replacement filter cartridge is not available. The dispenser and the icemaker will not operate without the filter or filter bypass plug.

		Filter
	Filter	Bypass
		Plug
	Bypass
	Plug
	SmartWater	Water by Culligan

To use the filter bypass plug on Water by Culligan models, you must first remove the filter adapter from the cartridge holder by turning it to the left.

For the maximum benefit of your filtration system, GE recommends the use of GE branded SmartWater filters only. Using GE branded filters in GE and Hotpoint refrigerators provides optimal performance and reliability. GE branded SmartWater filters are always the right choice because they are patented and designed specifically for GE products. GE SmartWater filters meet rigorous industry NSF standards for safety and quality that are important for products that are filtering your water. GE has not qualified non-GE branded filters for use in GE and Hotpoint refrigerators and there is no assurance that non-GE branded filters meet GE’s standards for quality, performance and reliability.

,I \RX KDYH TXHVWLRQV³YLVLW RXU :HEVLWH DW GEAppliances.com, or call 1.800.GE.CARES (1.800.432.2737).

Replacement filters:

To order additional filter cartridges in the United States, visit our Website at GEAppliances.com, or call GE Parts and Accessories, 800.626.2002.

See filter label for type of filter to order (MWF or MSWF).
Customers in Canada should consult the yellow pages for the
nearest Mabe Service Center.	7

About the shelves and bins.

Not all features are on all models.

Snugger

Refrigerator bin

Freezer bin

Refrigerator Door Bins and Freezer Door Tilt-Out Bins

Large Bins

The larger refrigerator door bins and freezer tilt-out door bins are adjustable.

To remove: Lift the front of the bin straight up, then lift up and out.

To replace or relocate: Engage the back side of the bin in the molded supports of the door. Then push down on the front of the bin. Bin will lock in place.

Small Bins

To remove: Lift the front of the bin straight up then out.

To replace: Position the bin above the rectangular molded supports on the door. Then slide the bin down onto the support to lock it in place.

The snugger helps prevent tipping, spilling or sliding of small items stored on the door shelf. Place a finger on either side of the snugger near the rear and move it back and forth to fit your needs.

Top freezer bin

CAUTION:

Be careful when placing items in the top bin. Make sure that items do not block or fall into the ice chute.

Freezer tilt-out bin

Slide-Out Spillproof Shelf

The slide-out spillproof shelf allows you to reach items stored behind others. The special edges are designed to help prevent spills from dripping to lower shelves.

Press tab and pull shelf forward to remove

To remove:

Slide the shelf out until it reaches the stop, then press down on the tab and slide the shelf straight out.

To replace or relocate:

Line the shelf up with the supports and slide it into place. The shelf can be repositioned when the door is at 90° or more. To reposition the shelf, slide the shelf past the stops and angle downward. Slide shelf down to the desired

position, line up with the supports and slide into place.

Make sure you push the shelves all the way back in before you close the door.

Freezer Baskets (on some models)

To remove, slide out to the stop position, lift the front past the stop position, and slide out.

Make sure you push the baskets all the way back in before you close the door.

Freezer Baskets (on some models)

To remove, push the basket all the way to the back of the freezer. Lift up until the back pins are disengaged. Lift the entire basket up and pull out.

Make sure you push the baskets all the way back in before you close the door.

8

About the shelves and bins.			GEAppliances.com
Not all features are on all models.
		QuickSpace™ Shelf (on some models)

This shelf splits in half and slides under itself for storage of tall items on the shelf below.

This shelf can be removed and replaced or relocated just like Slide-Out Spillproof Shelves.

On some models, this shelf can not be used in the lowest position.

Slide-Out Freezer Shelves

To remove, slide out to the stop position, lift the front past the stop position, and slide out from rib.

Make sure you push the shelves all the way back in before you close the door.

Fixed Freezer Shelves

To remove, lift the shelf up at the left side and then bring the shelf out.

NOTE FOR DISPENSER MODELS: In order to take full advantage of the tilt-out ice bin (on some models), only store items on the shelf below the ice bin that are no taller than the lowest point on the bin.

Door Wine/Beverage Rack

(on some models)

This rack holds up to 5 cans, one bottle of wine or one 2-liter bottle of soda.

The rack hangs from the sides of the dairy bin.

To remove:

Empty the wine/beverage rack.

Holding the bottom of the dairy bin, lift the front straight up, then lift up and out.

To detach the rack from the dairy bin, pull the rack’s side wires out of the holes on each side of the dairy bin.

To replace:

Reattach the rack to the sides of the bin.

Engage the back side of the bin in the molded supports on the door. Then push down on the front of the bin. The bin will lock into place.

ShelfSaver™ Rack

(on some models)

Use this rack to store beverage cans for easy access.

It can also hold a 9” x 13” baking dish.

Door Can Rack

(on some models)

This door rack holds up to 9 cans.

NOTE: This rack can only be mounted in the top position under the dairy bin.

Removable Beverage Rack

(on some models)

The beverage rack is designed to hold a bottle on its side. It can be attached to any slide-out shelf.

	1	To install:
		Line up the large part of the
2		slots on the top of the rack with
		the tabs under the shelf.
		Then slide the rack back to lock
		it in place.

9

About the refrigerator doors.

Refrigerator Doors (on some models)

The refrigerator doors may feel different than the ones you are used to. The special door opening/closing feature makes sure the doors close all the way and are securely sealed.

When opening and closing the door you will notice a stop position. If the door is opened past this stop point, the door will remain open to allow you to load and unload food more easily. When the door is only partially open, it will automatically close.

The resistance you feel at the stop position will be reduced as the door is loaded with food.

When the door is only partially open, it will automatically close.

Beyond this stop the door will stay open.

	7/16” Socket Wrench
	To remove the base
	grille, open the doors,
	remove the screw at
	each end of the base
	grille and then pull	Raise
	the grille straight out.

Door Alignment

If doors are uneven, adjust the refrigerator door.

Using a 7/16” socket wrench, turn the door adjusting screw to the right to raise the door; to the left, to lower it. (A nylon plug, imbedded in the threads of the pin, prevents the pin from turning unless a wrench is used.)

After one or two turns of the wrench, open and close the refrigerator door and check the alignment at the top of the doors.

10

About the crispers and pans.

GEAppliances.com

Not all features are on all models.

Fruit and Vegetable Crispers

Excess water that may accumulate in the bottom of the drawers should be wiped dry.

On some models, the bottom drawer has full extension slides that allow full access to the drawer.

HI LO

				C
			D	O
				D
	O	L		L
C				E
				S
				T

Adjustable Humidity Crispers

Slide the control all the way to the HI setting to	Slide the control all the way to the LO setting to
provide high humidity recommended for most	provide lower humidity levels recommended for
vegetables.	most fruits.

Convertible Deli Pan (on some models)

The convertible deli pan has its own cold air duct to allow a stream of cold air from the freezer compartment or refrigerator compartment to flow to the pan.

The variable temperature control regulates the air flow from the Climate Keeper.

Set the control to the coldest setting to store fresh meats.

Set the control to cold to convert the panto normal refrigerator temperature and provide extra vegetable storage space. The cold air duct is turned off. Variable settings between these extremes can be selected.

About crisper removal.

Not all features are on all models.

Crisper Removal

Crispers can easily be removed by pulling the drawer straight out and lifting the drawer up and over the stop location.

If the door prevents you from taking out the drawers, first try to remove the door bins.

If this does not offer enough clearance, the refrigerator will need to be rolled forward until the door opens enough to slide the drawers out. In some cases, when you roll the refrigerator out, you will need to move the refrigerator to the left or right as you roll it out.

11

About the automatic icemaker.

A newly installed refrigerator may take 12 to 24 hours to begin making ice.

Automatic Icemaker

7KH LFHPDNHU ZLOO SURGXFH VHYHQ FXEHV SHU F\FOH³ approximately 100–130 cubes in a 24-hour period, depending on freezer compartment temperature, room temperature, number of door openings and other use conditions.

If the refrigerator is operated before the water connection is made to the icemaker, set the power switch in the OFF position.

When the refrigerator has been connected to the water supply, set the power switch to the ON position.

The icemaker will fill with water when it cools to 15°F (–10°C). A newly installed refrigerator may take 12 to 24 hours to begin making ice cubes.

Special note about dispenser models:

Some models have a tilt-out ice bin. The bin can be tilted out as shown in the illustrations, and it will hold itself up while you take ice out or turn the icemaker power switch on and off. Be sure to put the bin back in place before closing the door.

To restore your ice level from an empty bucket stage, the following steps are recommended:

12 hours after the first batch of ice has fallen into the bin, dispense 3 to 4 cubes.

After an additional 6 hours, dispense 3 to 4 cubes again.

You will hear a buzzing sound each time the icemaker fills with water.

Throw away the first few batches of ice to allow the water line to clear.

Be sure nothing interferes with the sweep of the feeler arm.

When the bin fills to the level of the feeler arm, the icemaker will stop producing ice. It is normal for several cubes to be joined together.

If ice is not used frequently, old ice cubes will become cloudy, taste stale and shrink.

These steps will restore your ice level in the shortest amount of time.

	Icemaker	Power	Icemaker
		Switch

	Power	Feeler Arm	Green
	Switch
			Power Light	Feeler Arm
		(on some models)	(on some models)

NOTE:

In homes with lower than average water pressure, you may hear the icemaker cycle multiple times when making one batch of ice.

12

About the automatic icemaker. (cont)

GEAppliances.com

Accessing Ice and Reaching the Power Switch on Dispenser Models

There are two types of ice storage bins on dispenser models.

One has a shelf above the bin, the other does not.

Special note for models with tilt-out ice bin:

These models have a tilt-out ice bin. The bin can be tilted out as shown in the illustrations, and it will hold itself up while you take ice out or turn the icemaker power switch on and off. Be sure to put the bin back in place before closing the door.

NOTE: In order to take full advantage of the tilt-out ice bin, only store items on the shelf below the ice bin that are no taller than the lowest point on the bin.

Models with a shelf above the ice bin

Shelf

Ice Bin

To access ice, pull the bin forward.

Shelf

Ice Bin

To reach the power switch, pull the shelf straight out. Always be sure to replace the shelf.

Models with tilt out ice bin			On some models, to access ice or reach the power switch:
To access ice and reach the icemaker power switch:

Lift the bin, then pull it forward until the bin stops.

Lower the bin to access ice or reach the power switch.

Pull the bin forward until the bin stops.

Lower the bin to access ice or reach the power switch.

Removing Ice Bin (dispenser models) CAUTION: The ice bin is heavy when full.

Set the power switch to the OFF position before removing the bin.

When replacing the bin, be sure to press it firmly into place. If it does not go all the way back, remove it and rotate the drive mechanism 1/4 turn. Then push the bin back again.

Rotate

Drive

Mechanism

Dispenser Models only

13

About the ice and water dispenser. (on some models)

To Use the Dispenser

	Select CUBED ICE	, CRUSHED ICE
	or WATER
	Press the glass gently against the top of the
	dispenser cradle.
	The spill shelf is not self-draining. To reduce
	water spotting, the shelf and its grille should be
	cleaned regularly.
	If no water is dispensed when the
	refrigerator is first installed, there may be air
Spill Shelf	in the water line system. Press the dispenser
	arm for at least two minutes to remove
	trapped air from the water line and to fill the
	water system. To flush out impurities in the
	water line, throw away the first six glassfuls
	of water.

CAUTION: Never put fingers or any other objects into the ice crusher discharge opening.

Locking the Dispenser

Press the LOCK pad for 3 seconds to lock the dispenser and control

panel. To unlock, press and hold the pad again for 3 seconds.

Dispenser Light

This pad turns the night light in the dispenser on and off. The light also comes on when the dispenser cradle is pressed. For models with a bulb, if the light burns out, it should be replaced with a 6 watt 12V maximum bulb. For LED models, contact Factory Service.

Quick Ice (on some models)

When you need ice in a hurry, press this pad to speed up ice production. This will increase ice production for the following 48 hours or until you press the pad again.

Door Alarm (on some models)

To set the alarm, press this pad until the indicator light comes on. This alarm will sound if either door is open for more than 3 minutes. The light goes out and the beeping stops when you close the door.

Important Facts About Your Dispenser

Do not add ice from trays or bags to the storage drawer. It may not crush or dispense well.

Avoid overfilling glass with ice and use of narrow glasses. Backed-up ice can jam the chute or cause the door in the chute to

freeze shut. If ice is blocking the chute, poke it through with a wooden spoon.

Beverages and foods should not be quickchilled in the ice storage drawer. Cans, bottles or food packages in the storage drawer may cause the icemaker or auger to jam.

To keep dispensed ice from missing the glass, put the glass close to, but not touching, the dispenser opening.

Some crushed ice may be dispensed even though you selected CUBED ICE. This happens occasionally when a few cubes accidentally get directed to the crusher.

After crushed ice is dispensed, some water may drip from the chute.

Sometimes a small mound of snow will form on the door in the ice chute. This condition is normal and usually occurs when you have dispensed crushed ice repeatedly. The snow will eventually evaporate.

14

Care and cleaning of the refrigerator.

GEAppliances.com

Dispenser drip area.

Cleaning the Outside

The dispenser drip area, beneath the grille, should be wiped dry. Water left in this area may leave deposits. Remove the deposits by adding undiluted vinegar to the well. Soak until the deposits disappear or become loose enough to rinse away.

The dispenser cradle. Before cleaning, lock the dispenser by pressing and holding the LOCK pad for 3 seconds. Clean with warm water and

EDNLQJ VRGD VROXWLRQ³DERXW D WDEOHVSRRQ ml) of baking soda to a quart (1 liter) of water. Rinse thoroughly and wipe dry.

The door handles and trim. Clean with a cloth dampened with soapy water. Dry with a soft cloth.

The stainless steel panels and door handles

(on some models) can be cleaned with a commercially available stainless steel cleaner. A spray-on stainless steel cleaner works best.

Do not use appliance wax or polish on the stainless steel.

Keep the outside clean. Wipe with a clean cloth lightly dampened with kitchen appliance wax or mild liquid dish detergent. Dry and polish with a clean, soft cloth.

Do not wipe the refrigerator with a soiled dish cloth or wet towel. These may leave a residue that can erode the paint. Do not use scouring pads, powdered cleaners, bleach or cleaners containing bleach because these products can scratch and weaken the paint finish.

Cleaning the Inside

To help prevent odors, leave an open box of baking soda in the fresh food and freezer compartments.

Unplug the refrigerator before cleaning. If this is not practical, wring excess moisture out of sponge or cloth when cleaning around switches, lights or controls.

8VH ZDUP ZDWHU DQG EDNLQJ VRGD VROXWLRQ³ about a tablespoon (15 ml) of baking soda to a quart (1 liter) of water. This both cleans and neutralizes odors. Rinse and wipe dry.

Use of any cleaning solution other than that which is recommended, especially those that contain petroleum distillates, can crack or damage the interior of the refrigerator.

Avoid cleaning cold glass shelves with hot water because the extreme temperature difference may cause them to break. Handle glass shelves carefully. Bumping tempered glass can cause it to shatter.

Do not wash any plastic refrigerator parts in the dishwasher.

The chill/thaw tray is dishwasher safe.

15

Care and cleaning of the refrigerator. (cont.)

Behind the Refrigerator

Be careful when moving the refrigerator away from the wall. All types of floor coverings can be damaged, particularly cushioned coverings and those with embossed surfaces.

Pull the refrigerator straight out and return it to position by pushing it straight in. Moving the refrigerator in a side direction may result in damage to the floor covering or refrigerator.

When pushing the refrigerator back, make sure you don’t roll over the power cord or icemaker supply line (on some models).

Preparing for Vacation

For long vacations or absences, remove food and unplug the refrigerator. Clean the interior with a baking soda solution of one tablespoon (15 ml) of baking soda to one quart (1 liter) of water. Leave the doors open.

Set the icemaker power switch to the OFF position and shut off the water supply to the refrigerator.

If the temperature can drop below freezing, have a qualified servicer drain the water supply system (on some models) to prevent serious property damage due to flooding.

Preparing to Move

Secure all loose items such as shelves and drawers by taping them securely in place to prevent damage.

When using a hand truck to move the refrigerator, do not rest the front or back of the refrigerator against the hand truck. This could damage the refrigerator. Handle only from the sides of the refrigerator.

Be sure the refrigerator stays in an upright position during moving.

Replacing the light bulbs. (on some models)

Note: Turning the refrigerator off via the controls on the touch panel does not shut off electrical power to the refrigerator.

Your light shield will look like one of the following:

Tabs

OR

5HIULJHUDWRU &RPSDUWPHQW³8SSHU /LJKW

Unplug the refrigerator.

The bulbs are located at the top of the compartment, inside the light shield. On some models, a screw at the front of the light shield will have to be removed. On other models, the screw is located in the pocket located at the back of the shield.

To remove the light shield, on some models, press in on the tabs on the sides of the shield and slide forward and out. On other models, just slide the shield forward and out.

After replacing the bulb with an appliance bulb of the same or lower wattage, replace the light shield and screw. When replacing the light shield, make sure that the tabs at the back of the shield fit into the slots at the back of the light shield housing.

Plug the refrigerator back in.

Pocket

16

Replacing the light bulbs. (cont)	GEAppliances.com
5HIULJHUDWRU &RPSDUWPHQW³/RZHU /LJKW

This light is located above the top drawer. Unplug the refrigerator.

Lift the light shield up and pull it out.

After replacing the bulb with an appliance bulb of the same or lower wattage, replace the shield.

Plug the refrigerator back in.

Freezer Compartment

Unplug the refrigerator.

Remove the shelf just above the light shield. (The shelf will be easier to remove if it is emptied first.) Remove the screw at the top of the light shield.

To remove the light shield, press in on the sides, and lift up and out.

Replace the bulb with an appliance bulb of the same or lower wattage, and reinstall the light shield. When reinstalling the light shield, make sure the top tabs snap securely into place. Replace the screw.

Reinstall the shelf and plug the refrigerator back in.

Dispenser (on some models)

Unplug the refrigerator.

The bulb is located on the dispenser under the control panel. Remove the light bulb by turning it counterclockwise.

Replace the bulb with a bulb of the same size and wattage.

Plug the refrigerator back in.

Replacing the lights on models with LED lighting

Setting the controls to OFF does not remove power to the light circuit. Not all features are on all models.

			Refrigerator Compartment (on some models)
			There is an LED lighting display in the top and sides of the fresh food compartment and in the rear
			and side of the freezer compartment on some models.
		LED
		Lighting	If this assembly needs to be replaced, call GE Service at 1.800.432.2737 in the United States or
		Display	1.800.561.3344 in Canada.

17

Installation	Refrigerator
Instructions	Models 22, 23, 25, 26, 27 & 29

Questions? Call 800.GE.CARES (800.432.2737) or Visit our Website at: GEAppliances.com In Canada, call 1.800.561.3344 or Visit our Website at: www.geappliances.ca

BEFORE YOU BEGIN

Read these instructions completely and carefully.

IMPORTANT ³ 6DYH WKHVH LQVWUXFWLRQV IRU local inspector’s use.

IMPORTANT ³ 2EVHUYH DOO JRYHUQLQJ codes and ordinances.

Note to Installer – Be sure to leave these instructions with the Consumer.

1RWH WR &RQVXPHU ² .HHS WKHVH LQVWUXFWLRQV IRU future reference.

6NLOO OHYHO ² ,QVWDOODWLRQ RI WKLV DSSOLDQFH UHTXLUHV basic mechanical skills.

&RPSOHWLRQ WLPH ² Refrigerator Installation 30 minutes

Water Line Installation 30 minutes

3URSHU LQVWDOODWLRQ LV WKH UHVSRQVLELOLW\ RI WKH installer.

3URGXFW IDLOXUH GXH WR LPSURSHU LQVWDOODWLRQ LV QRW covered under the Warranty.

If the refrigerator has already been installed, remove the base grille (see Step 2 in Moving the Refrigerator), then skip to Step 5 in Installing the Refrigerator.

PREPARATION

WATER SUPPLY TO THE ICEMAKER

If the refrigerator has an icemaker, it will have to be connected to a cold water line. A GE water supply kit (containing tubing, shutoff valve, fittings and instructions) is available at extra cost from your dealer, by visiting our Website at GEAppliances. com (in Canada at www.geappliances.ca) or from Parts and Accessories, 800.626.2002 (in Canada 1.800.661.1616).

TOOLS YOU WILL NEED

3/8” and 5/16” Socket		1/2” and 7/16” Wrench

Plastic Putty Knife

Phillips Head Screwdriver

18

Installation Instructions

MOVING THE REFRIGERATOR

1LOADING THE REFRIGERATOR ONTO A HAND TRUCK

Leave all tape and door pads on doors until the refrigerator is in its final location.

To move the refrigerator, use a padded hand truck. Center the refrigerator on the hand truck and secure the strap around the refrigerator.

DO NOT OVERTIGHTEN THE STRAP.

2 REMOVE THE BASE GRILLE

Remove the grille by removing the two Phillips head screws.

If the refrigerator must go through any entrance that is less than 38” wide, the doors must be removed. Proceed to Step 3.

DO NOT remove the handles.

If all entrances are more than 38” wide, skip to Installing the Refrigerator.

3DISCONNECT THE WATER COUPLING

(on some models)

If the refrigerator has a water dispenser, there is a water line from the cabinet into the bottom hinge on the freezer door that must be disconnected.

To disconnect, push in on the white collar of the coupling and pull out the tubing.

White collar

Bottom freezer hinge

19

Installation Instructions

MOVING THE REFRIGERATOR (CONT.)

4DISCONNECT THE POWER COUPLING (on some models)

If the refrigerator has a water dispenser, there is a power line (harness) from the cabinet into the bottom hinge on the freezer door that must be disconnected.

To disconnect, pull apart at the coupling.

Bottom freezer hinge

5DISCONNECT THE ELECTRICAL CONNECTORS (on some models)

If the refrigerator has a refreshment center, there are electrical connectors (harnesses) from the cabinet into the bottom hinge on the refrigerator door that must be disconnected.

To disconnect, pull apart each connector.

Bottom refrigerator hinge

6CLOSE THE FREEZER AND REFRIGERATOR DOORS

7 REMOVE THE FREEZER DOOR

ARemove the freezer door top hinge cover (if equipped) by either squeezing it and pulling it up or by prying it off with a plastic putty knife.

		Remove the two 5/16” hex head screws, then
B
		lift the hinge straight up to free the hinge pin.
		5/16” Hex Head

C Open the freezer door to 90.°

90°

20

Installation Instructions

7 REMOVE THE FREEZER DOOR (cont.)

DAs one person slowly lifts the freezer door up and off the bottom hinge, the second person should carefully guide the water line and power line (harness) through the bottom hinge.

90°

ESet the door on a non-scratching surface with the inside up.

8 REMOVE THE REFRIGERATOR DOOR

ARemove the refrigerator door top hinge cover (if equipped) by either squeezing it and pulling it up or by prying it off with a plastic putty knife.

8

B

C

REMOVE THE REFRIGERATOR DOOR

(cont.)

Remove the two 5/16” hex head screws, then lift the hinge straight up to free the hinge pin.

5/16” Hex Head

Open the refrigerator door to 90.°

90°

21

Installation Instructions

MOVING THE REFRIGERATOR (CONT.)

8REMOVE THE REFRIGERATOR DOOR

(cont.)

DLift the refrigerator door up and off the bottom hinge.

If the refrigerator has a refreshment center, one person should slowly lift the door up and off the bottom hinge and the second person should carefully guide the electrical lines (harnesses) through the bottom hinge.

90°

Refreshment Center Models only

ESet the door on a non-scratching surface with the inside up.

9 REPLACING THE DOORS

To replace the doors, simply reverse steps 3 through 8.

However, please note the following:

:KHQ ORZHULQJ WKH GRRUV RQWR WKH ERWWRP hinges, make sure the second person carefully guides the tube and harnesses through the holes in the hinges.

:KHQ FRQQHFWLQJ WKH ZDWHU OLQH PDNH VXUH you insert the tubing all the way to the mark.

Mark

'R QRW SLQFK WKH WXELQJ DQG KDUQHVVHV ZKHQ placing the doors on the bottom hinges.

:KHQ FRQQHFWLQJ WKH SRZHU OLQH DQG WKH electrical lines (refreshment center models only), be sure that the connectors are seated together fully.

22

Installation Instructions

INSTALLING THE REFRIGERATOR

REFRIGERATOR LOCATION

Do not install the refrigerator where the temperature will go below 60°F (16°C) because it will not run often enough to maintain proper temperatures.

Do not install the refrigerator where the temperature will go above 100°F (37°C) because it will not perform properly.

Install it on a floor strong enough to support it fully loaded.

CLEARANCES

Allow the following clearances for ease of installation, proper air circulation and plumbing and electrical connections:

	23‘/25‘	23‘ (33” wide),
	CustomStyle™	25‘, 26‘, 27‘, 29‘
Sides	1/8” (4 mm)	1/8” (4 mm)
Top	1” (25 mm)	1” (25 mm)
Back	1/2” (13 mm)	-1” (25 mm)

DIMENSIONS AND SPECIFICATIONS

		Water	Electrical
		3/4” (19 mm)
		Airspace
	24” (61 cm)	(1/2” [13 mm] Gap	25” (63.5 cm)
		+ 1/4” [6 mm] Wall
	Cabinet		Countertop
		Plates)

DIMENSIONS AND SPECIFICATIONS (for 23‘ CustomStyle™ models)

701ø4” (178.4 cm)

36”

(91.4 cm)

24” (61 cm)

DIMENSIONS AND SPECIFICATIONS (for 25‘ CustomStyle™ models)

721ø4” (183.5 cm)*

36”

(91.4 cm)

24” (61 cm)

*721/4” (183.5 cm) required for full adjustment of mobility wheels. If cabinets installed above refrigerator have doors that are flush to the top of the opening for the refrigerator, then an additional 1/8” may be required to provide clearance for cabinet doors to open freely.

23

Installation Instructions

INSTALLING THE REFRIGERATOR (CONT.)

1CONNECTING THE REFRIGERATOR TO THE HOUSE WATER LINE

(icemaker and dispenser models)

A cold water supply is required for automatic icemaker and dispenser operation. If there is not a cold water supply, you will need to provide one. See “Installing the Water Line” section.

NOTES:

%HIRUH PDNLQJ WKH FRQQHFWLRQ WR WKH refrigerator, be sure the refrigerator power cord is not plugged into the wall outlet.

,I \RXU UHIULJHUDWRU GRHV QRW KDYH D ZDWHU filter, we recommend installing one if your water supply has sand or particles that could clog the screen of the refrigerator’s water valve. Install it in the water line near the refrigerator.

If using GE SmartConnect™ Refrigerator Tubing Kit, you will need an additional tube (WX08X10002) to connect the filter. Do not cut plastic tube to install filter.

AIf you are using copper tubing, place a compression nut and ferrule (sleeve) onto the end of the tubing coming from the house cold water supply.

If you are using the GE SmartConnect™ tubing, the nuts are already assembled to the tubing.

BIf you are using copper tubing, insert the end of the tubing into the refrigerator connection, at the back of the refrigerator, as far as possible. While holding the tubing, tighten the fitting.

If you are using GE SmartConnect™ tubing, insert the molded end of the tubing into the refrigerator connection, at the back of the refrigerator, and tighten the compression nut until it is hand tight. Then tighten one additional turn with a wrench. Overtightening may cause leaks.

CFasten the tubing into the clamp provided to hold it in position. You may need to pry open the clamp.

Tubing Clamp

1/4” Tubing

1/4” Compression Nut

Ferrule (sleeve)

	Refrigerator	SmartConnect™ Tubing
	Connection

Option 2

2	TURN ON THE WATER SUPPLY

Turn the water on at the shutoff valve (house water supply) and check for any leaks.

3 PLUG IN THE REFRIGERATOR

Before plugging in the refrigerator, make sure the icemaker power switch is set to the OFF position.

See the grounding information attached to the power cord.

24

Roller adjusting screws

Installation Instructions

4 PUT THE REFRIGERATOR IN PLACE

Move the refrigerator to its final location.

5 LEVEL THE REFRIGERATOR

The refrigerator can be leveled by adjusting the rollers located near the bottom hinges.

		Rollers
				Raise

Rollers have three purposes:

Rollers adjust so the door closes easily when opened about halfway. (Raise the front about 5/8” [16 mm] from the floor.)

Rollers adjust so the refrigerator is firmly positioned on the floor and does not wobble.

Rollers allow you to move the refrigerator away from the wall for cleaning.

To adjust the rollers on 23‘ (33” wide), 25‘, 26‘, 27‘ and 29‘ models:

Turn the roller adjusting screws clockwise to raise the refrigerator,

counterclockwise to lower it. Use a 3/8” hex socket

or wrench, or an adjustable wrench.

Roller adjusting screw

5 LEVEL THE REFRIGERATOR (cont.)

To adjust the

rollers on 23‘/25‘

CustomStyle™ models:

Turn the front roller adjusting screws clockwise to raise the refrigerator,

counterclockwise to lower it. Use a 3/8” hex

wrench with extension, or an adjustable wrench.

These models also have rear adjustable rollers so you can align the refrigerator with your kitchen cabinets. Use a 3/8” hex wrench with extension to turn the screws for the rear

UROOHUV³clockwise to raise the refrigerator, counterclockwise to lower it.

6 LEVEL THE DOORS

AAdjust the refrigerator door to make the doors even at the top.

BTo align:

Using a 7/16” wrench, turn the door adjusting screw to the right to raise the door, to the left to lower it.

NOTE:

A nylon plug, imbedded in the threads of the pin, prevents the pin from turning unless a wrench is used.

After one or two turns of the wrench, open and close the refrigerator door and check the alignment at the top of the doors.

Doors should be even at top

Raise

7/16” wrench

25

Installation Instructions

INSTALLING THE REFRIGERATOR (CONT.)

7 REPLACE THE BASE GRILLE

Replace the grille by installing the two Phillips head screws.

8 SET THE CONTROLS

Set the controls to the recommended setting.

9 START THE ICEMAKER

Set the icemaker power switch to the I (on) position. The icemaker will not begin to operate until it reaches its operating temperature of 15°F (–9°C) or below. It will then begin operation automatically. It will take 2–3 days to fill the ice bin.

Power switch

Power switch

NOTE:

In lower water pressure conditions, the water valve may turn on up to 3 times to deliver enough water to the icemaker.

26

Installation Instructions

INSTALLING THE WATER LINE

BEFORE YOU BEGIN

Recommended copper water supply kits are WX8X2, WX8X3 or WX8X4, depending on the amount of tubing you need. Approved plastic water supply lines are GE SmartConnect™ Refrigerator Tubing (WX08X10006, WX08X10015 and WX08X10025).

When connecting your refrigerator to a GE Reverse Osmosis Water System, the only approved installation is with a GE RVKit. For other reverse osmosis water systems, follow the manufacturer’s recommendations.

If the water supply to the refrigerator is from a Reverse Osmosis Water Filtration System AND the refrigerator also has a water filter, use the refrigerator’s filter bypass plug. Using the refrigerator’s water filtration cartridge in

conjunction with the RO filter can result in hollow ice cubes and slower water flow from the water dispenser.

This water line installation is not warranted by the refrigerator or icemaker manufacturer. Follow these instructions carefully to minimize the risk of expensive water damage.

Water hammer (water banging in the pipes) in house plumbing can cause damage to refrigerator parts and lead to water leakage or flooding. Call a qualified plumber to correct water hammer before installing the water supply line to the refrigerator.

To prevent burns and product damage, do not hook up the water line to the hot water line.

If you use your refrigerator before connecting the water line, make sure the icemaker power switch is in the OFF position.

Do not install the icemaker tubing in areas where temperatures fall below freezing.

When using any electrical device (such as a power drill) during installation, be sure the device is double insulated or grounded in a manner to prevent the hazard of electric shock, or is battery powered.

All installations must be in accordance with local plumbing code requirements.

(ICEMAKER & DISPENSER MODELS)

WHAT YOU WILL NEED

&RSSHU RU *( 6PDUW&RQQHFW™ Refrigerator Tubing kit, 1/4” outer diameter to connect the refrigerator to the water supply. If using copper, be sure both ends of the tubing are cut square.

To determine how much tubing you need: measure the distance from the water valve on the back of the refrigerator to the water supply pipe. Be sure there is sufficient extra tubing to allow the refrigerator to move out from the wall after installation.

GE SmartConnect™ Refrigerator Tubing Kits are available in the following lengths:

6’ (1.8 m) – WX08X10006 15’ (4.6 m) – WX08X10015 25’ (7.6 m) – WX08X10025

27

Installation Instructions

INSTALLING THE WATER LINE (CONT.)

WHAT YOU WILL NEED (CONT.)

NOTE: The only GE approved plastic tubing is that supplied in GE SmartConnect™ Refrigerator Tubing kits. Do not use any other plastic water supply line because the line is under pressure at all times.

Certain types of plastic will crack or rupture with age and cause water damage to your home.

A GE water supply kit (containing tubing, shutoff valve and fittings listed below) is available

at extra cost from your dealer or from Parts and Accessories, 800.626.2002 (in Canada 1.800.661.1616).

A cold water supply. The water pressure must be between 20 and 120 p.s.i. (1.4–8.1 bar).

Power drill.

1/2” or adjustable wrench.

6WUDLJKW DQG 3KLOOLSV EODGH VFUHZGULYHU

Two 1/4” outer diameter compression nuts and 2 ferrules (sleeves)³WR FRQQHFW WKH FRSSHU WXELQJ WR the shutoff valve and the refrigerator water valve.

OR

,I \RX DUH XVLQJ D *( 6PDUW&RQQHFW™ Refrigerator Tubing kit, the necessary fittings are preassembled to the tubing.

,I \RXU H[LVWLQJ FRSSHU ZDWHU OLQH KDV D IODUHG ILWWLQJ at the end, you will need an adapter (available

at plumbing supply stores) to connect the water line to the refrigerator OR you can cut off the flared fitting with a tube cutter and then use a compression fitting. Do not cut formed end from GE SmartConnect™ Refrigerator tubing.

Shutoff valve to connect to the cold water line. The shutoff valve should have a water inlet with a minimum inside diameter of 5/32” at the point of connection to the COLD WATER LINE. Saddle-type shutoff valves are included in many water supply kits. Before purchasing, make sure a saddle-type valve complies with your local plumbing codes.

Install the shutoff valve on the nearest frequently used drinking water line.

1 SHUT OFF THE MAIN WATER SUPPLY

Turn on the nearest faucet long enough to clear the line of water.

2 CHOOSE THE VALVE LOCATION

Choose a location for the valve that is easily accessible. It is best to connect into the side of a vertical water pipe. When it is necessary to connect into a horizontal water pipe, make the connection to the top or side, rather than at the bottom, to avoid drawing off any sediment from the water pipe.

3 DRILL THE HOLE FOR THE VALVE

Drill a 1/4” hole in the water pipe (even if using a self-piercing valve), using a sharp bit. Remove any burrs resulting from drilling the hole in the pipe.

Take care not to allow water to drain into the drill.

Failure to drill a 1/4” hole may result in reduced ice production or smaller cubes.

28

Installation Instructions

4 FASTEN THE SHUTOFF VALVE

Fasten the shutoff valve to the cold water pipe with the pipe clamp.

Pipe Clamp

Saddle-Type		Vertical Cold Water Pipe
Shutoff Valve

NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.

5 TIGHTEN THE PIPE CLAMP

Tighten the clamp screws until the sealing washer begins to swell.

NOTE: Do not overtighten or you may crush the tubing.

Washer

Pipe Clamp	Inlet End

Clamp

Screw

6 ROUTE THE TUBING

Route the tubing between the cold water line and the refrigerator.

Route the tubing through a hole drilled in the wall or floor (behind the refrigerator or adjacent base cabinet) as close to the wall as possible.

NOTE: Be sure there is sufficient extra tubing to allow the refrigerator to move out from the wall after installation.

7 CONNECT THE TUBING TO THE VALVE

Place the compression nut and ferrule (sleeve) for copper tubing onto the end of the tubing and connect it to the shutoff valve.

Make sure the tubing is fully inserted into the valve. Tighten the compression nut securely.

For plastic tubing from a GE SmartConnect™ Refrigerator Tubing kit, insert the molded end of the tubing into the shutoff valve and tighten compression nut until it is hand tight, then tighten one additional turn with a wrench. Overtightening may cause leaks.

Saddle-Type	Compression Nut
Shutoff Valve	SmartConnect™ Tubing

Packing Nut

Outlet ValveFerrule (sleeve)

NOTE: Commonwealth of Massachusetts Plumbing Codes 248CMR shall be adhered to. Saddle valves are illegal and use is not permitted in Massachusetts. Consult with your licensed plumber.

8 FLUSH OUT THE TUBING

Turn the main water supply on and flush out the tubing until the water is clear.

Shut the water off at the water valve after about one quart (1 liter) of water has been flushed through the tubing.

To complete the installation of the refrigerator, go back to Step 1 in Installing the Refrigerator.

29

Normal operating sounds.

Newer refrigerators sound different from older refrigerators. Modern refrigerators have more features and use newer technology.

Do you hear what I hear? These sounds are normal.

					HUMMM...
				WHOOSH...
	The new high efficiency compressor may run faster					You may hear
	and longer than your old refrigerator and you may							the fans spinning at high speeds. This happens when
	hear a high-pitched hum or pulsating sound while it is							the refrigerator is first plugged in, when the doors are
	operating.							opened frequently or when a large amount of food is
	Sometimes the refrigerator runs for an extended period,							added to the refrigerator or freezer compartments. The
								fans are helping to maintain the correct temperatures.
	especially when the doors are opened frequently. This
	means that the Frost Guard™ feature is working to					If either door is open for over 3 minutes, you may hear
	prevent freezer burn and improve food preservation.							the fans come on in order to cool the light bulbs.
	You may hear a whooshing sound when the doors close.					The fans change speeds in order to provide optimal
	This is due to pressure equalizing within the refrigerator.							cooling and energy savings.
			CLICKS, POPS,						WATER SOUNDS
	CRACKS and CHIRPS
	You may hear cracking or popping sounds when the
	refrigerator is first plugged in. This happens as the					The flow of
	refrigerator cools to the correct temperature.
								refrigerant through the freezer cooling coils may make
	Electronic dampers click open and closed to provide							a gurgling noise like boiling water.
	optimal cooling and energy savings.					Water dropping on the defrost heater can cause a
	The compressor may cause a clicking or chirping sound							sizzling, popping or buzzing sound during the defrost
	when attempting to restart (this could take up to 5							cycle.
	minutes).					A water dripping noise may occur during the defrost
	The electronic control board may cause a clicking							cycle as ice melts from the evaporator and flows into
	sound when relays activate to control refrigerator							the drain pan.
	components.					Closing the door may cause a gurgling sound due to
	Expansion and contraction of cooling coils during and							pressure equalization.
	after defrost can cause a cracking or popping sound.
	On models with an icemaker, after an icemaking cycle,
									For additional information on normal
	you may hear the ice cubes dropping into the ice
	bucket.								icemaker and dispenser operating sounds,
									see the About the automatic icemaker and
									About the ice and water dispenser sections.

30