GE CP350ST2SS, CP350ST3SS, JP356BM4BB, JP356SM4SS, JP356WM4WW Installation Guide

...

0 (0)

I stollotio

I structio s

30" ectricCooktop

CP350, JP336, JP340, JP346, JP356, PP912, PP932,

PP942, PP944, PP945, PP950

I-_ If you have questions, call 800.GE.CARES or visit our website at: GEAppliances.com

BEFORE YOU BEGIN

Read these instructions completely and carefully.

. IMPORTANT - Soretheseinstructions

for local inspector's use.

, IMPORTANT - Observeollgoverning

codes and ordinances.

, Note to Installer- Be sure to leave these

instructions with the Consumer.

, Note to Consumer - Keep these instructions for

future reference.

, Product failure due to improper installation is not

covered under the Warranty.

A WARNING - This appliance must be

properly grounded.

. ATTENTION INSTALLER - ALL

COOKTOPS MUST BE HARD WIRED {DIRECT

WIRED) INTO AN APPROVED JUNCTION BOX. A

"PLUG AND RECEPTACLE" IS NOT PERMITTED

ON THESE PRODUCTS.

, Proper installation is the responsibility of the

installer and product failure due to improper

installation is NOT covered under warranty.

MATERIALS YOU WILL NEED

Junction Box Wire Nuts

TOOLS YOU WILL NEED

Pencil

Phillips Head

Screwdriver

Ruler or Straightedge

Saber Saw

1/8" Drill Bit & Electric or

Hand Drill

Safety Glasses

PARTS INCLUDED

4 Screws

(WB1X!!37)

Foam Tape

2 Hold Down

Brackets

31-10637-7 (07-!] GE) 1

Installation Instructions

IMPORTANT SAFETY INSTRUCTIONS

FOR YOUR SAFETY

, For Personal Safety, remove house fuse or open

circuit breaker before beginning installation.

Failure to do so could result in serious injury or

death.

, Be sure your cooktop is installed properly by a

qualified installer or service technician.

, To eliminate the risk of burns or fire due to

reaching over heated surface elements, cabinet

storage located above the surface units should

be avoided. If cabinet storage space is to be

provided, the risk con be reduced by installing a

range hood that projects horizontally a minimum

of 5" beyond the bottom of the cabinets. Cabinet

installation above the cooktop may be no deeper

than 13".

, Hake sure the cabinets and wall coverings

around the cooktop can withstand the

temperatures (up to 200°F) generated y the

cooktop.

, The cooktop should be easy to reach and lighted

with natural light during the day.

, Always disconnect the electrical service to

the cooktop before repairing or servicing the

cooktop. This can be done by disconnecting the

fuse or circuit breaker. Failure to do this could

result in a dangerous or fatal shock. Know where

your main disconnect switch is located. If you do

not know, have your electrician show you.

ELECTRICAL REQUIREMENTS

This appliance must be supplied with the proper

voltage and frequency, and connected to an

individual, properly grounded branch circuit,

protected by a circuit breaker or a time delay fuse

as noted on name plate.

We recommend you have the electrical wiring and

hookup of your cooktop connected by a qualified

electrician. After installation, have the electrician

show you where your main cooktop disconnect is

located.

Wiring must conform to National Electrical Code.

You can get a copy of the National Electrical Code,

ANSI/NFPA No. 70-Latest Edition, by writing:

National Fire Protection Association

Batterymarch Park

Quincy, HA 02269

The cooktop conduit wiring is approved for copper

wire connection only, and if you have aluminum

house wiring, you must use special UL approved

connectors for joining copper to aluminum.

You must use a two-wire, three conductor 208/240

VAC, 60 Hertz electrical system. A white (neutral)

wire is not needed for this unit. The cooktop must

be installed in a circuit that does not exceed 125

VAC nominal to ground.

Refer to the name plate on your cooktop for the

KW rating for your cooktop.

Name plate location

Installation Instructions

PRE-INSTALLATION CHECKLIST

WARN ING - Theelectricalpowerto

the cooktop supply line must be shut off while

connections are being made. Failure to do so

could result in serious injury or death.

r_ When preparing cooktop opening, make sure

the inside of the cabinet and the cooktop do

not interfere with each other. (See section on

preparing the opening.)

r_ Remove packaging materials and literature

package from the cooktop before beginning

installation.

........

Cooktop _L

r6]

Remove Installation

Instructions from literature

pack and read them

carefully before you begin.

Be sure to place all

literature, Owner's Manual,

Installations, etc. in a safe

place for future reference.

_SYINSTALLA_ONOFYOURN_W

SO"COOKT_

Make sure you have all the tools and materials

you need before starting the installation of the

cooktop.

Your home must provide the adequate

electrical service needed to safely and

properly use your cooktop. (Refer to section on

electrical requirements.)

When installing your cooktop in your home,

make sure all local codes and ordinances are

followed exactly as stated.

Hake sure the wall coverings, countertop and

cabinets around the cooktop can withstand

heat (up to 200°F) generated by the cooktop.

PREPARING THE OPENING

r_ The following MINIMUM clearance dimensions

must be maintained.

13" MAX. Depth of unprotected

overhead cabinets

1-1/2" MIN.

Clearance from

cutout to side wall

on the right of the

unit

30" IVllN.

Clearance from 15" MIN. Height

countertop to countertop to

unprotected nearest cabinet on

overhead either side of unit

surface

2" IV]IN.Clearance

from cutout to side

wall on the left of

the unit

If a 30" clearance between the cooking surface and

overhead combustible materials or metal cabinets

cannot be maintained, a minimum clearance of 24"

is required and the underside of the cabinets above

the cooktop must be protected with not less than

1/4" insulating millboard covered with sheet metal

not less than 0.0122" thick.

r_ OVERALL COOKTOP DIMENSIONS

29-]/4" _ 21-]/8"(21-1/2"SS)

('nn_nn _ 4-3/16" Rear

_ _..... _ __-_""_ at the conduit

°"_ _ 28' 6-1/4" Rear

19-1/4"

on Model PP945

-_-- & PP950

r_ VERTICAL CLEARANCE

Allow 5" minimum 8-_/4"

vertical clearance

from the cooktop

bottom (or 8-1/8"

minimum depth from

the countertop) to any

combustible surfaces,

such as a cabinet

drawer.

]

Installation Instructions

PREPARING THE OPENING (Cont)

CUTOUT DIMENSIONS

OF THE COUNTERTOP

To insure accuracy, it is best to make a template

when cutting the opening in the counter.

th of cut

i-3/4" Min. Between _ cut i-_ " _ I

cutout and the wall _/ _ I

2-1/2" Min. from front edge I II

of cutout and front edge of

countertop

JXTR32X CUTOUT FILLER TRIM KIT:

A filler trim kit is available for use if your countertop

cutout is larger than the dimensions shown, up to

29-13/16" x 20-7/16". Order JXTR32X to reduce the

cutout opening for installation of this cooktop. This

kit may be ordered from your GE Dealer.

r_ Hake sure the wall coverings, countertop and

cabinets around the cooktop can withstand

heat (up to 200°F) generated by cooktop.

countertop must

withstand heat up

to 200°F. /

E_ For Americans with Disabilities Act (ADA)

Forward Approach Installation Only:

For models with

no drop box,

allow 5" minimum

depth between the

countertop and an

enclosure.

For models with

a drop box, allow

6-1/2" minimum

depth between the

countertop and an

enclosure.

(PP945)

Drop / I1_

box _=1

NOTE: The enclosure must be made of wood

material. Also, an access panel is required for the

junction box, hold-down brackets, and service.

Installation Instructions

INSTALLING THE COOKTOP

INSTALLING THE JUNCTION BOX

Install an approved junction box where it will be

easily reached through the front of the cabinet

where the cooktop will be located. The cooktop

conduit is 3 feet long.

Install junction box sothat

it can be reached through

the front of the cabinet.

]

16"

Min.

A IMPORTANT: The junction box must be

locatedwhere itwillallow considerableslackin

the conduitforserviceability.

F_ PROTECT SURFACE OF COOKTOP

Place a towel or tablecloth onto the countertop.

Lay the cooktop upside down onto the protected

surface.

Bottom of Cooktop

Cloth under Cooktop

F_ ATTACH FOAM TAPE

Apply the foam tape around the outer edge of the

glass. Do not overlap the foam tape.

Bottom of Cooktop

-- -.. Foam_Tape ................"..........o z

Note: On CP350S, PP912S, PP932S, PP942S, PP944S,

PP945S & PP950S models, apply the foam tape

around the outer edge of the glass on the sides and

rear of the unit only.

LOCATE MOUNTING PARTS

Remove the hold down brackets and screws from

the literature package.

Mounting Screw

Fsl ATTACH BRACKETS TO COOKTOP

Screw the hold down bracket to the side

of the cooktop unit. Repeat for opposite side of

cooktop.

Cooktop Glass

Hold Down

Bracket

+ 11 hidden pages