Feiyutech WG User Manual
FY WG 3 Axis Wearable Gimbal is compatible with GoPro HERO4 / 3+ / 3 and cameras with
similar dimensions. Reserved mounting space for GoPro LCD Touch BacPac
Manual Version 2.0
Introduction
FY WG is a lightweight, yet feature-rich, wearable 3 axis gimbal capable of capturing immersive and fully stabilized footages. It is
1
compatible with GoPro HERO4/ 3+/ 3 (with optional mounting space for GoPro LCD BacPac) and other cameras with similar dimensions.
The FY WG is a miniaturized version of the best-selling FeiYu gimbal, offering exceptional stabilization technology in a wearable form factor
for action cameras. A GoPro T-Clamp adapter is packaged with every FY WG. Users can attach the gimbal to any accessories supporting
the GoPro three-prong mount. The FY WG also contains two 1/4"-20 tripod mounts on its gimbal body, allowing the gimbal to be mounted
in different orientations to all universal tripod screw mount accessories (including helmets, bikes, selfie sticks and other accessories).
Install
2
STEP 1
Remove the screws on the
battery compartment,
insert two16340 batteries
and tighten the screws.
WARNING !WARNING !
!
Do not power on the
Do not power on the
gimbal before completing
gimbal before completing
all the installation steps.
all the installation steps.
STEP 2 STEP 3
Mount the camera carefully
to the mounting bracket
and tighten the screws.
Ensure the camera is mounted securely. Press and hold the function button
for 2 seconds. The LED light will turn blue.
Press the function button and hold for 3 seconds, it will be powered off.
Camera In LeftCamera In Left
Vertical
POWERING
ON / OFF
Accessories For
3
Hexagonal Socket
Head Cap Screw
1
3M
Adhesive
Please choose one way:
Use the 3M Adhesive to fix the bottom of the Gimbal.
1
2
Use with GoPro Accessories, mount the provided T-clamp to the side
or the bottom of the gimbal. Attach T-clamp to any accessories
supporting the standard GoPro three-prong mount.
3
The gimbal can also be mounted directly to other accessories using
the standard 1/4" tripod mount. Tighten all screws and ensure it is
firmly mounted before using the gimbal.
Forward Inverted
2
T-Clamp
1/4 Inch Screws
Tilting Axis
Function Button
ON
/
（
Rolling Axis
OFF
）
Panning Axis
Video And Camera
Charging Interface
Function
Interface
Camera in Right
Operation
3
Function
Function
Button
Button
Operating Modes and Functions
Operating Modes and Functions
Mode #1 - Panning Mode
Mode #2 - Panning and Til�ng Mode Camera is permitted to pan left or right and tilt up and down. Rolls are restricted.
Mode #3 - Lock Mode
Inversion Mode
Pressing the function button three consecutive times in any operating mode, the gimbal will switch to the
Inverted Mode (Allowing the user to flip the gimbal orientation upside down). Pressing the function button three more times
while in Inverted Mode to switch back to the original orientation
Manual Pulling Locking
and the Lock Mode. Adjust the title angle to the desired position and wait for 0.5 second until the gimbal registers the new angle.
Reset
Tilt and Level Calibra�on
For more information, please refer to G4 Remote Control section in the instruction manual.
Switch between different operating modes by pressing the function button.
The LED light will flash distinctively to indicate different operating modes.
Camera is permitted to pan left or right. Vertical tilts or rolls are restricted.
Camera stays in its current orientation. All panning, tilting and rolls are restricted.
After the gimbal has been powered on for eight seconds, the tilt angle can be adjusted manually in the Panning Mode
Pressing the function button four consecutive times will reset the gimbal to initial orientation.
By using the optional G4 Remote Control, tilt and level can be adjusted without the need to connect to a computer.
Camera in Right
.
Camera In Left
Tilting
Function
Button
Camera in Right
Panning
Function Button Quick Reference
Operation LED Status
Single Tap
Double Tap
Triple Tap
Quadruple Tap
LED Flashes Once
LED Flashes Twice
LED Flashes Once
LED Flashes Once
Function Explanation
Panning Mode
Panning and Tilting Mode
Inversion Mode
Reset
Operation LED Status Function
Long Press
For 1 Second
Long Press
For 2 Second
Long Press
For 3 Second
On Constantly
Turn On And Switch To
The Mode’s LED Status
Turn Off After
A moment
Sound
Lock Mode
Two Beeps
Three Beeps Shutdown
Power On
* When the gimbal is in the Inverted Mode, pressing the function button three consecutive times will revert back to the original orientation.
When the battery is low, the gimbal will make three beeping sound and automatically shut down itself.
Rolling
Screws For
The Battery
Compartment
T-Clamp Screw Hole
1/4 Inch Screw Hole
T-Clamp
Screw Hole
1/4 Inch
Screw Hole
T-Clamp
Screw Hole
Accessories
4
Charger
Input: DC 5V
Output: DC 4.2V
Rechargeable
Battery
Type: 16340
Video Output
and Camera
Charging Cable
Video
Output
Cable
Hexagonal
Socket Head
Cap Screw
M2*6mm
USB Connector
M 1.5 Allen Key
USB Cable
T-Clamp
Curved Adhesive
Mounts
Long screw
Quick-Release
Buckle
Extension Knurled
Thumb Screw
3M Adhesive
Charging
USB Cable
USB Power
Adapter
（Not Included）
FY Remote Control (Optional Item)
5
Function
Interface
Tip：The Remote Control will be
automatically powered off to
save battery if there is no operation
within three minutes.
Wireless Remote Control
Steps to connect wireless remote control:
1
Open the wireless remote control: Long press the function button on
wireless remote control for one second to power on.
2
Install the receiver for wireless remote control: Insert the receiver for
wireless remote control into the function port of gimbal .
3
Open the gimbal: Long press the function button on gimbal for two
seconds to turn on the gimbal.
4
Use the wireless remote control to control the gimbal.
Charging
Remote Control Distance
Match Code
Keep the gimbal powered on, restart the remote control
and connect the receiver of RC to the gimbal, press the remote control
function button for 7 times in 5 seconds, if the indicator on the RC flashes
5 times it means the receiver and the transmitter of RC match successfully,
then customer can control the gimbal by the RC.
▲ RC needs to be match code whenever the following situations：（1）Connecting properly but still control in fail. （2）Change the receiver or wireless remote control.
Connect the Micro interface of wireless remote control with
5V charger by USB cable.
15 meters in an open environment.
Receiver
for wireless
remote control
!
Please install
the receiver
properly before
power on
Wireless
remote control
Joystick
Function
Button
With the remote control, you can switch the gimbal mode or adjust the angle from a distance.
Wired remote control
Power on / off
Operation
Long press for
0.5 second
Long press for
3 seconds
Power
ON
OFF
Function
Interface
Direction Button
UP LEFT RIGHTDOWN
USB Data Cable for RC
Remote Control Operation Instructions
Operation
Single Tap
Double Tap
Triple Tap Triple tap againInversion Mode
Quadruple Tap Reset
Tap Button
Six Times
Tap Button
Seven Times
Long Press
For 1 Second
Long Press
For 3 Second
Note: The function button on the Gimbal will be disabled after connect the Remote Control
Explanation
Mode #1 Panning Mode
Mode #2 Panning and Tilting Mode
Calibration Using Remote Control
Match Code Mode
Mode #3 Lock Mode
Turn Off The Gimbal
Wireless RC
Remark
,exit inversion mode into original status
Single tap ,exit calibration and enter standby. Wake the
gimbal by pressing the function button once again
Match code when connecting properly but still control
in fail or change the receiver/wireless remote control.
Function
Button
Direction
Button
Firmware Upgrade
!
Be sure to insert the
!
batteries before upgrading
Function
Interface
USB Cable
WARNING
Make sure that the
connec�on to the
computer is done by the
USB Connector
Upgrade........
PC
Firmware Upgrade Instruction
Please visit the official website of Feiyu Tech: www.feiyu-tech.com to download the USB driver, firmware upgrade software and the latest firmware.
Unzip the compressed file locally to your computer. Refer to the connection diagram on how to connect the gimbal with the computer. Please
follow the instructions inside the firmware upgrade package carefully, or there will be a risk of rendering the gimbal inoperable.
Attention : Please make sure that the connection to the computer is done by the USB connector.
Tilt and Level Calibration
The tilt and level settings can be calibrated through the use of the configuration software. User can adjust the tilt and diagonal rotation in small intervals
to better adapt to his/her filming scene. Before any calibration, please insert the batteries into the gimbal and refer to the connection diagram to
connect the gimbal with the computer.
Attention : Please make sure that the connection to the computer is done by the USB connector.
Video and Camera Charging Interface
Function
Interface
This interface can be output 5 voltage and receive analog video signal from GoPro
Connect the video output and camera charging cable as the above diagram
can power the GoPro camera and view video signal from the GoPro camera.
Video Output Cable
After connecting the video output and camera charging
cable, the analog monitor can be used as a display.
Note: The Analog Monitor are equipped by users.
Analog Monitor
(
Equipped by users )
Initialize The Gimbal
FY WG needs to be initialized whenever the
following situations are observed after power on
1. The tilt angle is not leveled with the horizontal
surface.
2. The roll angle is not parallel to the horizontal
surface.
3. When the gimbal is Full-Axis-Lock mode,
the camera does not stay stationary..
DISCLAIMER
FY WG 3-Axis Wearable Gimbal is a feature-rich camera stabilizer, yet lightweight and portable.
It is prohibited for any user to use the gimbal for any illegal purposes.
Guilin Feiyu Electronic Technology Co.,Ltd and our associates assume no liability for any accident, injury,
death, loss, or other claim related to or resulting from the use of this product. In no event shall Guilin Feiyu
Electronic Technology Co.,Ltd and our associates be liable for incidental or consequential damages relating
to or resulting from the use of this product or any of its parts. Damage resulting from use, accident, or normal
wear and tear is not covered by our warranty.
Guilin Feiyu Electronic Technology Co.,Ltd reserves the right to amend this manual and the terms and
conditions of this product at any time.
Initialization Instructions
1. Ensure gimbal is fully assembled and camera
is installed properly.
2. Place the gimbal on a flat surface and keep it
stationary.
3. Power on the Gimbal.
4. Wait for the gimbal to finish its initialization
before resuming the use of the gimbal.
When initialization is completed,
Note:
the LED light will quickly flash.
Please visit the official website of Feiyu Tech
to get related information: www.feiyu-tech.com
Technical support: service@feiyu-tech.com
Motionless Flat Surface
Everyone
Can Make a Movie
Parameters
53.4 mm
91 mm
35 mm
95 mm
Working Voltage
Vertical Tilting Angle
Rolls Angle
Horizontal Panning Angle
Tilting Increments
Panning Increments
Static Attitude
Tracking Accuracy
Motion Attitude
Tracking Accuracy
Overload Current
Protection
Weight
Usage Time 3 ~ 4 Hours
Camera Maximum Height
Camera Maximum Thickness
Camera Maximum Weight
ATTENTION
Please assemble the gimbal in accordance to
the diagram provided.
Please upgrade the firmware and configuration
settings with the provided USB data cable.
Please charge the battery with the provided
battery charger.
Please install the camera securely before
powering on the gimbal.
6.0 V ~ 9 V
320°
100°
320°
2°/S ~ 75°/S
3°/S ~ 150°/S
0.01 ~ 0.05
(
Working Voltage)
0.1 ~ 0.5
(
Motor Overload<2G)
800 mA
188 g (Without
Batteries & Camera
43.6 mm
( Replaceable
mounting bracket )
31.7 mm
( Replaceable
mounting bracket )
150 g
)
Loading...