Beko WMD 75106 Manual

Washing Machine

WMD 75106

Перална машина

Perilica rublja

Plně automatická pračka

	1 Warnings	Safety instructions
		• This appliance must be connected to
	General Safety
	• Never place your machine on a carpet	an earthed outlet protected by a fuse of
		suitable capacity.
	covered floor. Otherwise, lack of airflow
		• The supply and draining hoses must
	from below of your machine may cause
		always be securely fastened and remain in
	electrical parts to overheat. This may cause
		an undamaged state.
	problems with your washing machine.
		• Fit the draining hose to a washbasin or
	• If the power cable or mains plug is
		bathtub securely before starting up your
	damaged you must call Authorized Service
		machine. There may be a risk of being
	for repair.
		scalded due to high washing temperatures!
	• Fit the drain hose into the discharge
		• Never open the loading door or remove the
	housing securely to prevent any water
		filter while there is still water in the drum.
	leakage and to allow machine to take in
		• Unplug the machine when it is not in use.
	and discharge water as required. It is very
		• Never wash down the appliance with a
	important that the water intake and drain
		water hose! There is the risk of electric
	hoses are not folded, squeezed, or broken
		shock!
	when the appliance is pushed into place
		• Never touch the plug with wet hands. Do
	after it is installed or cleaned.
		not operate the machine if the power cord
	• Your washing machine is designed to
		or plug is damaged.
	continue operating when the power
		• For malfunctions that cannot be solved by
	restores after a power interruption. The
		information in the operating manual:
	machine will resume its program when the
		• Turn off the machine, unplug it, turn off
	power restores. Press the “Start/Pause/
		the water tap and contact an authorized
	Cancel” button for 3 seconds to cancel the
		service agent. You may refer to your local
	program (See, Canceling a Program)
		agent or solid waste collection center in
	• There may be some water in your machine
		your municipality to learn how to dispose of
	when you receive it. This is from the quality
		your machine.
	control process and is normal. It is not
		If there are children in your
	harmful to your machine.
	• Some problems you may encounter may	house...
	be caused by the infrastructure. Press	• Keep children away from the machine
	“Start/Pause/Cancel” button for 3 seconds	when it is operating. Do not let them
	to cancel the program set in your machine	tamper with the machine.
	before calling the authorized service.	• Close the loading door when you leave the
	First Use	area where the machine is located.
	• Carry out your first washing process
	without loading your machine and with
	detergent under “Cottons 90°C” program.
	• Ensure that the cold and hot water
	connections are made correctly when
	installing your machine.
	• If the current fuse or circuit breaker is less
	than 16 Amperes, please have a qualified
	electrician install a 16 Ampere fuse or
	circuit breaker.
	• While using with or without a transformer,
	do not neglect to have the grounding
	installation laid by a qualified electrician.
	Our company shall not be liable for any
	damages that may arise when the machine
	is used on a line without grounding.
	• Keep the packaging materials out of reach
	of children or dispose them by classifying
	according to waste directives.
	Intended use
	• This product has been designed for home
	use.
	• The appliance may only be used for
	washing and rinsing of textiles that are
	marked accordingly.

2 - EN

2 Installation

Removing packaging reinforcement

Tilt the machine to remove the packaging reinforcement. Remove the packaging reinforcement by pulling the ribbon.

Opening the transportation locks

ATransportation safety bolts must be removed before operating the washing machine! Otherwise, the machine will be damaged!

1.Loosen all the bolts with a spanner until they rotate freely (“C”)

2.Remove transportation safety bolts by turning them gently.

3.Fit the covers (supplied in the bag with the Operation Manual) into the holes on the rear panel. (“P”)

C Keep the transportation safety bolts in a safe place to reuse when the washing machine needs to be moved again in the future.

C Never move the appliance without the transportation safety bolts properly fixed in place!

Adjusting the feet

ADo not use any tools to loosen the lock nuts. Otherwise, they can be damaged.

1.Manually (by hand) loosen the lock nuts on the feet.

2.Adjust them until the machine stands level and firmly.

3.Important: Tighten all lock nuts up again.

•If you are going to use your double waterinlet machine as a single (cold) water-inlet unit, you must install the stopper*, supplied with your machine to the hot water valve.

•If you want to use both water inlets of the product, you can connect the hot water hose after removing the stopper and gasket group from the hot water valve.

* Applies for the products supplied with a blind stopper group.

•Models with a single water inlet should not be connected to the hot water tap.

When returning the appliance to its place after maintenance or cleaning, care should be taken not to fold, squeeze or block the hoses.

Connecting to the drain

The water discharge hose can be attached to the edge of a washbasin or bathtub. The drain hose should be firmly fitted into the drain as to not get out of its housing.

Important:

•The end of the drain hose must be directly connected to the wastewater drain or to the washbasin.

•The hose should be attached to a height of at least 40 cm, and 100 cm at most.

•In case the hose is elevated after laying it on the floor level or close to the ground (less than 40 cm above the ground), water discharge becomes more difficult and the laundry may come out wet.

Connecting to the water supply.

Important:

•The water supply pressure required to run the machine must be 1-10 bar (0,1 – 1 MPa).

•Connect the special hoses supplied with the machine to the water intake valves on the machine.

•The hose should be pushed into the drainage for more than 15 cm. If it is too long you may have it shortened.

•The maximum length of the combined hoses must not be longer than 3.2 m.

3 - EN

Electrical connection

Connect the machine to an earthed outlet protected by a fuse of suitable capacity.

Important:

• Connection should comply with national regulations.

• The voltage and the allowed fuse protection are specified in the section “Technical Specifications”.

• The specified voltage must be equal to your mains voltage.

• Connection via extension cords or multiplugs should not be made.

BA damaged power cable must be replaced by a qualified electrician.

BThe appliance must not be operated unless it is repaired! There is the risk of electric shock!

3 Initial preparations for

washing

Preparing clothes for washing

Laundry items with metal attachments such as, bras, belt buckles and metal buttons will damage the machine. Remove metal attachments or place the items in a clothing bag, pillow case, or something similar.

•Sort the laundry according to type of fabric, color, and degree of soiling and permissible water temperature. Always follow the advice on the garment labels.

•Place small items like infants’ socks and nylon stockings, etc. in a laundry bag, pillow case or something similar. This will also save your laundry from getting lost.

•Wash “machine washable” or “hand washable” labeled products only with an appropriate program.

•Do not wash colors and whites together. New, dark colored cottons may release a lot of dye. Wash them separately.

•Use only dyes/color changers and lime removers suitable for machine wash. Always follow the instructions on the packaging.

•Wash trousers and delicate clothes turned inside out.

Correct load capacity

C Please follow the information in the "Program Selection Table". Washing results will degrade when the machine is overloaded.

Loading door

The door locks during program operation and the Door Locked Symbol lights up. The door can be opened when the symbol fades out.

Detergents and softeners

Detergent Drawer

The detergent drawer is composed of three compartments:

The detergent dispenser may be in two different types according to the model of your machine.

–(I) for prewash

–(II) for main wash - (III) siphon

–() for softener

Detergent, softener and other cleaning agents

Add detergent and softener before starting the washing program.

Never open the detergent dispenser drawer while the washing program is running!

When using a program without pre-wash, no detergent should be put into the pre-wash compartment (Compartment no. I).

Detergent quantity

The amount of washing detergent to be used depends on the amount of laundry, the degree of soiling and water hardness.

•Do not use amounts exceeding the quantities recommended on the package to avoid problems of excessive foam, poor rinsing, financial savings and finally, environmental protection.

•Never exceed the (> max <) level marking; otherwise, the softener will be wasted without being used.

•Do not use liquid detergent if you want to wash using the time delay feature.

4 - EN

4 Selecting a Program and Operating Your Machine

Control panel

Figure 1

1			7		3				6		8

		2
			5		4
1	- Spin Speed Adjustment Button				5	- Auxiliary Function Keys
2	- Time Delaying Button (+/-)				6	- Program Selection Knob
3	-	Temperature Adjustment Button			7	-	Display
4	-	Start/Pause/Cancel Button			8	-	On/Off Button

Figure 2

7.a

-

Spin Speed Indicator

Display symbols

7.b

-

Temperature Indicator

7.c

-

Spin Symbol

7.d

-

Temperature Symbol

7.e

-

Remaining Time and Delaying Time

Indicator

7.f

-

Programme Indicator Symbols (pre-

wash/main wash/rinse/softener/spin)

7.g

-

Economy Symbol

7.h

-

Time Delaying Symbol

7.i

-

Door Locked Symbol

7.j

-

Start Symbol

7.k

-

Standby Symbol

7.l

-

Auxiliary Function Symbols

7.m -

Water cut-off Symbol (According to

your machine’s model)

Turning the machine on

Plug in your machine. Turn the tap on completely. Check if the hoses are connected tightly. Place the laundry in the machine. Add detergent and softener. Press the “On/Off” button.

Program selection

Turn the Programme Selection Knob to the program mode that you wish to wash your

laundry.

The recommended temperature and spin speed for the selected program appear. Press “Start/Pause/Cancel” button to start the program.

C Sort the laundry according to type of fabric, color, degree of soiling and permissible water temperature when choosing a program.

5 - EN

Main programs

Depending on the type of textile, the following main programs are available:

• Cottons

You can wash your durable clothes with this program. Your laundry will be washed with vigorous washing movements during a longer washing cycle.

• Synthetics

You can wash your less durable clothes on this program. Lighter washing movements and shorter washing cycle is used compared to “Cottons” program. It is recommended for your synthetic clothes (such as shirts, blouses, synthetic/cotton blended garments, etc.). For curtains and lace, the “Synthetic 40” program with pre-wash and anti-creasing functions selected is recommended.

• Woollens

You can wash your machine-washable woolen garments on this program. Wash by selecting the proper temperature according to the labels of your clothes. It is recommended to use appropriate detergents for woolens.

Additional programs

For special cases, there are also extra programs available:

C Additional programs may differ according to the model of your machine.

• Babycare

Increased hygiene is provided by a longer heating period and an additional rinse cycle. It is recommended for baby clothes and clothes worn by allergic people.

• Delicate

You can wash your delicate clothes on this program. It has more sensitive washing movements and does not make intermediate spinning compared to “Synthetic” program.

• Hand wash

You can wash your woolen/delicate clothes that bear “not machinewashable” labels for which hand wash is recommended on this program. It washes the laundry with very tender washing movements without damaging your clothes.

• Mini 30

This program is used to quickly wash a small number of lightly soiled cotton garments.

• Super 40

This program washes for a longer period at 40°C and gives the same result as the

“Cottons 60°C” program, thus it saves energy. It is suitable for clothes for which you cannot use the “Cottons 60°C” program.

• Intensive

You can wash your durable and heavily soiled clothes on this program. In this program, your clothes will be washed for a longer time and

an extra rinse cycle will be made compared to the “Cottons” program.

Economy Symbol

Shows energy saving programs and temperature selections.

As “Intensive” and “Baby” programs are long programs with higher temperature selections to ensure hygiene, “Economy” Symbol will not light up.

Special programs

For specific applications, you can select any of the following programs:

• Rinse

This program is used when you want to rinse or starch separately.

• Spin

This program spins with maximum possible rpm in the default setting.

C You should use a lower spin speed for delicate laundries.

• Pump

This program is used to discharge the water of the clothes soaked into water in the machine.

Temperature selection

Whenever a new program is selected, the temperature anticipated for that program appears on the temperature indicator.

To change the temperature, press the “Temperature” button. Temperature decreases in 10° increments.

Cold selection is shown with “-” symbol.

	90˚C	Normally soiled, white cottons
		and linens.
		Normally soiled, fade proof
	60˚C	colored linens, cottons or
		synthetic clothes and lightly
		soiled white linens
	40˚C	Blended clothes including
	30°C	synthetics and woolens as well
	Cold	as delicates.

Spin Speed selection

Whenever a new program is selected, the maximum spin speed of the selected program is displayed on the spin speed indicator.

To decrease the spin speed, press the “Spin” button. Spin speed decreases gradually. Then, rinse hold and no spin options are shown respectively.

Rinse hold is shown with “” and no spin is shown with “ ” symbols.

If you do not want to unload your clothes immediately after the program, you may use the rinse hold function in order to prevent your

6 - EN

clothes become wrinkled in an anhydrous condition. With this function, your laundry is kept in the final rinsing water. If you want to spin your laundry after the rinse hold function:

-Adjust the spin speed.

-Press “Start/Pause/Cancel” button.

Program resumes. Your machine drains the water and spins your laundry.

You can use no spin function in order to drain the water without spinning at the end of the program.

Program selection and consumption table

	EN			2							Auxiliary functions
	Programme				LoadMax.(kg)	speedSpin(rpm) 1000-600	speedSpin(rpm) 1400-1200	ConsumptionWater (l)	ConsumptionEnergy (kWh)	speedSpin(rpm)	Prewash	WashQuick	PlusRinse	Creasing-Anti	HoldRinse	Temperature
Cottons			90		5	155	156	55	1.09	max.	•	•	•	•	•	90-Cold
Cottons			60**		5	134	135	45	0.85	max.	•	•	•	•	•	90-Cold
Cottons			40		5	133	134	45	0.65	max.	•	•	•	•	•	90-Cold
Super 40			40		5	161	162	50	1.02	max.					•	40
Intensive			60		5	198	199	65	1.65	max.			*	•	•	60-40
Babycare			90		5	141	142	64	2.37	max.			*		•	90-40
Synthetics			60		2.5	139	139	52	1.02	800	•	•	•	•	•	60-Cold
Synthetics			40		2.5	97	97	52	0.72	800	•	•	•	•	•	60-Cold
Delicate			40		2	75	75	51	0.33	600			•	•	•	40-Cold
Woollens			40		1.5	72	72	47	0.43	600			•		•	40-Cold
Hand wash			30		1	52	52	35	0.24	600						30-Cold
Mini 30			30		2.5	30	30	43	0.25	max.						30-Cold
										***
•	Selectable
*	Automatically selected, not cancelable.

**Energy Label program (EN 60456)

***Refers to 1400 rpm in machines with a highest spin speed above 1400 rpm. Refers to the highest spin speed in machines with a highest spin speed below 1400 rpm..

Water and power consumption and programme duration may differ from the table shown, subject to changes in water pressure, water hardness and temperature, ambient temperature, type and amount of laundry, selection of auxiliary functions, and fluctuations in the supply voltage.

“Super 40” program may be selected instead of “Cotton 60” programme during winter in areas where the input water temperature is low and/or in areas with low supply voltage.

C The auxiliary functions in the table may differ according to the model of your machine.

7 - EN

Auxiliary functions

Auxiliary Function Selection Buttons

C Select the required auxiliary functions before starting the program.

C Some combinations cannot be selected together. (Ex.: Pre-wash) (Figure 1-5a) and Quick Wash (Figure 1-5b).

Auxiliary function selection

If an auxiliary function that should not be selected together with a previously selected function is chosen, the first selected function will be cancelled and the last auxiliary function selection will remain active.

(Ex.: If you want to select pre-wash first and then quick wash, pre-wash will be cancelled and quick wash will remain active.

Auxiliary function that is not compatible with the program cannot be selected. (see, “Program Selection Table”)

• Prewash

When you select this function (5a), the display will indicate “1” symbol. A pre-wash is only worthwhile for heavily soiled laundry. Without pre-wash you save energy, water, detergent and time. Pre-wash without detergent is recommended for lace and curtains.

• Quick Wash

With this function (5b), the wash time is shortened. The “2” symbol will light up on the display. Use this function for smaller amounts or slightly soiled laundries.

• Rinse Plus

This function (5c) allows your machine to perform an extra rinsing in addition to the rinsing cycles performed by your machine after main washing cycle. Thus, the risk for sensitive skins (babies, allergic skins and etc.) to be effected by the minimal detergent remnants on the laundry is reduced. “3” symbol will light up on the display.

• Anti-Creasing

With this function (5d), drum movement will be lessened to prevent creasing and spinning speed is limited. In addition, washing is carried out at a higher water level. The “4” symbol will light up on the display.

C Whenever you select this auxiliary function, load your machine with half of the maximum laundry specified in the program table.

temperature, type and amount of laundry, auxiliary functions selected, and changes in the supply voltage.

Time delay

With the “Time delay” function you can delay the program start up to 24 hours. Setting can be made in intervals of 30 minutes.

1. Press “Time delaying” buttons “+” and “-” to set your desired time delay.

2. Press “Start/Pause/Cancel” button. Then the time delay starts to count down.

C More laundry may be loaded or taken out during the time delay period.

Changing the delay time

If you want to change the time during the countdown:

1.Press “Start/Pause/Cancel” button.

2.Press “Time delaying” buttons “+” or “-” to set the desired time delay.

3.Press “Start/Pause/Cancel” button.

Canceling the time delay

If you want to cancel the time delay countdown and start the program immediately:

1.Press “Start/Pause/Cancel” button.

2.Pres “Time Delaying” “-” button to decrease the time delay. Program duration after 30 minutes shall be displayed.

3.Press “Start/Pause/Cancel” button to start the program.

Starting the Program

1.Press “Start/Pause/Cancel” button to start the program.

2.The start symbol (Figure 2-7j) which indicates that the program has started will light up.

3.The door locks and the door locked symbol (Figure 2-7i) will light up.

4.The Symbol of the relevant step (prewash, main wash, rinse, softener and spin) that the program has started from will light up (Figure 2-7f).

C If the machine is not spinning, the program may be in rinse hold mode or the automatic spin correction system has been activated due to an excessive unbalanced distribution of laundry in the machine.

Time display

The display shows the time remaining for the program to complete while a program is running. Program duration may differ from the values in the consumption table

subject to the changes in the water pressure, water hardness and temperature, ambient

Changing the selections after the program has started

The selected spin speed and program temperature fade out. An empty frame appears.

When the “Program selection” button is

8 - EN

brought to the appropriate position, rpm and temperature data reappear.

Switching the machine to standby

mode

Press “Start/Pause/Cancel” button momentarily to switch your machine to the standby mode. Auxiliary functions can be cancelled or selected in accordance with the step the program is at. The door can be opened if the water level is suitable. Laundry may be added / taken out by opening the door.

Door lock

The Door Locked Symbol (Figure 2-7i) lights up when the loading door is locked. This symbol will flash until the door is allowed to open. Do not force the door at this stage. You may open the door after the symbol fades out.

Child-proof lock

This function protects the appliance from being tampered by children. In this case, all of the buttons are inactive except On/Off button; by On/Off button you can whether stop or resume (while child-lock on) the program of your machine.

The machine is switched to child-lock by pressing the 2nd and 4th auxiliary functions for 3 sec. “C:on” (Child lock is activated) label appears on the screen. The same symbol will also be displayed whenever any button is pressed while the machine is child-locked.

To deactivate the child-proof lock, press the 2nd and 4th auxiliary function buttons for 3 sec. “C:OFF” (Child lock is deactivated) label appears on the screen.

Ending the program through canceling

“Start/Pause/Cancel” button is pressed for 3 seconds to cancel the program. Start symbol (Figure 2-7j) will flash during cancellation. After cancellation, the symbol of the corresponding step at which the cancellation was made will remain lit and “End” will appear on the screen.

End of program

When the program is finished, the symbols of the relevant steps will remain lit up and the auxiliary function, spin and temperature data selected at the start-up of the program will remain selected. “End” will appear on the display.

5 Maintenance and cleaning

Detergent Drawer

Remove any powder residue buildup in the drawer. To do this;

1.Press the dotted point on the siphon in the softener compartment and pull towards you until the compartment is removed from the machine.

CIf more than a normal amount of water and softener mixture starts to gather in the softener compartment, the siphon must be cleaned.

2.Wash the dispenser drawer and the siphon with plenty of lukewarm water in a washbasin.

3.Replace the drawer into its housing after cleaning. Check if the siphon is in its original location.

Inlet water filters

There is a filter at the end of each water intake valve at the back side of the machine and also at the end of each water intake hose where they are connected to the tap. These filters prevent the foreign substances and dirt in the water to enter into the machine. Filters should be cleaned as they get dirty.

•Close the taps.

•Remove the nuts of the water intake hoses to clean the surfaces of the filters on the water intake valves with an appropriate brush.

•If the filters are very dirty, you can pull them out by means of pliers and clean them.

•Take out the filters on the flat ends of the water intake hoses together with the gaskets and clean thoroughly under streaming water.

•Replace the gaskets and filters carefully to their places and tighten the hose nuts by hand.

9 - EN

	Draining any remaining water and	by pulling out the plug at the end of the
	cleaning the pump filter	hose. If the amount of water to be drained
	Your product is equipped with a filter system	off is greater than the volume of the
		container, replace the plug, pour the water
	which ensures a cleaner water discharge that
		out, then resume the draining process.
	extends pump life by preventing solid items
		• After draining process is completed,
	such as buttons, coins and fabric fibers from
		replace the plug into the end of the hose
	clogging the pump propeller during discharge
		and fit the hose back into its place.
	of the washing water.
		If your product is not supplied with an
	• If your machine fails to drain the water,
		emergency drain hose, do the following as
	the pump filter may be clogged. You may
		shown in the figure below:
	have to clean it every 2 years or whenever
	it is plugged. Water must be drained off to
	clean the pump filter.
	In addition, water may have to be drained off
	completely in the following cases:
	• before transporting the machine (e.g. when
	moving house)
	• when there is the danger of frost
	In order to clean the dirty filter and discharge
	the water;	• Place a large container in front of the filter
	1- Unplug the machine to cut off the supply	to receive water flowing from the filter.
	power.	• Loosen pump filter (anticlockwise) until
	AThere may be water at 90°C in the	water starts to flow out of it. Direct the
	machine. Therefore, the filter must be	flowing water into the container you have
	cleaned only after the inside water is	placed in front of the filter. You can use a
	cooled down to avoid hazard of scalding.	piece of cloth to absorb any spilled water.
	2- Open the filter cap. The filter cap may be	• When there is no water left, turn the pump
	composed of one or two pieces according to	filter until it is completely loose and remove
	the model of your machine.	it.
	If it is composed of two pieces, press the tab	• Clean any residues inside the filter as
		well as fibers, if any, around the propeller
	on the filter cap downwards and pull the piece
		region.
	out towards yourself.
		• If your product has a water jet feature, be
	If it is composed of one piece, hold it from
		sure to fit the filter into its housing in the
	both sides and open it by pulling out.
		pump. Never force the filter while replacing
		it into its housing. Fit the filter fully into its
		housing; otherwise, water may leak from
		the filter cap.
		4- Close the filter cap.
		Close the two-piece filter cap of your product
		by pushing the tab on it.
	3- An emergency drain hose is supplied with	Close the one-piece filter cap of your product
	some of our models. Others are not supplied	by fitting the tabs on the bottom into their
	with this item.	positions and pushing the upper part of it.

If your product is supplied with an emergency drain hose, do the following as shown in the figure below:

•Pull out the pump outlet hose from its housing.

•Place a large container at the end of the hose. Drain the water off into the container

10 - EN

6 Solution suggestions for problems

Problem	Cause	Explanation / Suggestion
	Machine may have switched
Program cannot	to self protection mode due to	Reset your machine by pressing “Start/Pause/
be started or	an infrastructure problem (such	Cancel” button for 3 seconds. (see, Canceling a
selected.	as line voltage, water pressure,	Program)
	etc.).
There is water		Be sure the seals of the water inlet hoses are
coming from the	There might be problems with	securely fitted.
bottom of the	hoses or the pump filter.	Tightly attach the drain hose to the tap.
machine.		Make sure that the pump filter is completely closed.
Machine stopped	Machine can stop temporarily	It will resume operating when the voltage is back to
shortly after the	due to low voltage.	the normal level.
program started.
		The automatic spin correction system might have
It continuously		been activated due to the unbalanced distribution of
spins.		the laundry in the drum.
Remaining time	There may be an imbalance of	The laundry in the drum may be clustered (bundled
does not count		laundry in a bag). Laundry should be rearranged and
down.	laundry in the machine.	re-spun.
(For models with		No spinning is performed when the laundry is
a display)		not evenly distributed in the drum to prevent any
		damage to the machine and to its environment.
	In the case of a paused
	countdown while taking in	The machine will wait until there is a sufficient
	water:	amount of water to avoid poor washing results due
	Timer will not countdown until	to lack of water. Then the timer will start to count
	the machine is filled with the	down.
	correct amount of water.
	In the case of a paused
It continuously	countdown at the heating step:
	Time will not count down until
washes.
	the selected temperature for
Remaining time
	the program is reached
does not count
down.		The automatic spin correction system might have
(For models with
a display)		been activated due to the unbalanced distribution of
	In the case of a paused	the laundry in the drum.
	countdown at the spinning	The laundry in the drum may be clustered (bundled
	step:	laundry in a bag). Laundry should be rearranged and
	There may be an imbalance of	re-spun.
	laundry in the machine.	No spinning is performed when the laundry is
		not evenly distributed in the drum to prevent any
		damage to the machine and to its environment.

11 - EN

7 Specifications

Models	WMD 75106
Maximum dry laundry capacity (kg)	5
Height (cm)	84
Width (cm)	60
Depth (cm)	45
Net Weight (kg)	61
Electricity (V/Hz.)	230 V / 50Hz
Total Current (A)	10
Total Power (W)	2200
Spinning cycle (rpm max.)	1000

Specifications of this appliance may change without notice to improve the quality of the product. Figures in this manual are schematic and may not match your product exactly.

Values stated on the machine labels or in the documentation accompanying it are obtained in laboratory in accordance with the relevant standards. Depending on operational and environmental conditions of the appliance, values may vary.

This appliance’s packaging material is recyclable. Help recycle it and protect the environment by dropping it off in the municipal receptacles provided for this purpose. Your appliance also contains a great amount of recyclable material. It is marked with this label to indicate the used appliances that should not be mixed with other waste. This way, the appliance recycling organised by your manufacturer will be done under the best possible conditions, in compliance with European Directive 2002/96/EC on Waste Electrical and Electronic Equipment. Contact your town hall or your retailer for the used appliance collection points closest to your home. We thank you doing your part to protect the environment.

								8
On/Off	Start	Reset	Cottons	Synthetics	Woollens	Delicate	Babycare	Sport	Shirt	Hand	Pet hair
	Pause	3 sec.								wash	removal

Intensive	Rinse	Quick	Quick	Duvet	Anti	Rinse	Time	Temperature	No	Cold
	hold	wash	wash		creasing	plus	delay		heat
Prewash	Main	Rinse	Drain	Spin	No	Door	Wash	End	Child	Conditioner
	wash				spin	ready		proof lock

12 - EN

1 Предпазни мерки

Обща безопасност

•Никога не поставяйте пералнята на под, покрит с килим. В противен случай

възпрепятстването на достъпа на въздух отдолу може да доведе до прегряване на електрическите части и проблеми с пералната Ви машина.

•Ако захранващият кабел или шепсел са повредени, се свържете с оторизирания сервиз за ремонт.

•Наместете внимателно маркуча за източване в отводното гнездо за да избегнете изтичане на вода, като същевременно позволите на пералнята правилно да вкарва и изкарва вода. Много е важно маркучите за входяща и изходяща вода да не се прегънат, притиснат или пречупят при преместването на пералнята след нейното инсталиране или почистване.

•Вашата перална машина е настроена да продължи работата си след прекъсване на електрическото захранване. Пералнята няма да започне програмата отначало след възобновяване на захранването. Натиснете бутона Старт/Пауза/Отказ за 3 секунди за да откажете програмата (Виж “Отказ на програма”)

•Възможно е, при получаването на пералнята Ви, в нея да има известно количество вода, останало след процедурите за качествен контрол. Това е нормално и не вреди на пералнята Ви.

•Може възникналите проблеми да са причинени от външен проблем. Натиснете бутона Старт/Пауза/Отказ за 3 секунди за да откажете програмата, зададена в пералнята, преди да се обадите в оторизирания сервиз.

Първо ползване

•При първото ползване на пералната машина сложете перилен препарат без да зареждате пералнята с пране и пуснете на програма “Памучни тъкани 90°C”

•Уверете се, че отводите за топла и студена вода са свързани правилно при инсталацията.

•Ако бушонът или прекъсвачът Ви са под 16 Ампера, моля повикайте квалифициран електротехник да инсталира 16-Амперов бушон или прекъсвач.

•При употреба с или без трансформатор, уверете се, че заземяването на инсталацията е извършено от квалифициран електротехник. Фирмата ни не носи отговорност за повреди, възникнали в следствие на включване на пералнята в незаземен контакт.

•Дръжте опаковъчните материали от пералнята далеч от деца или ги изхвърлете в съответствие с изискванията за разделно изхвърляне на отпадъци.

Желателна употреба

•Този уред е предназначен за домашна употреба.

•Този уред може да се ползва за пране и

14 -

изплакване само на текстилни тъкани, означени по съответния начин.

Инструкции за безопасност

•Уредът трябва да бъде свързан към заземен контакт, защитен с предпазител с подходящ капацитет.

•Маркучите за входяща и изходяща вода трябва винаги да са надлежно свързани и невредими.

•Поставете внимателно изходящия маркуч

вмивката или ваната преди да стартиратe пералнята. Съществува риск от изгаряне поради високите температури на пране!

•Никога не отваряйте вратата на пералнята за да извадите филтъра ако в резервоара има останала вода.

•Извадете щепсела от контакта когато не ползвате нашината.

•Никога не мийте пералнята с маркуч за вода! Съществува риск от електрически удар!

•Никога не пипайте щепсела с мокри ръце. Не използвайте пералнята ако захранващият кабел или щепсел са повредени.

•При неизправности, за които информацията

втова ръководство не дава решение:

•Изключете пералнята, извадете щепсела от контакта, затворете крана за водата и се свържете с оторизирания сервиз. Може да се обърнете към местния агент или голям център за събиране на отпадъци в общината Ви, за да се информирате по какъв начин да изхвърлите пералнята.

Ако в дома си имате деца...

•Дръжте децата далеч от пералнята когато тя работи. Не им позволявайте да си играят с пералната машина.

•Затваряйте вратата на пералнята когато не се намирате близо до нея.

BG

2 Инсталация

Отстраняване на подсилващите опаковъчни материали

Наклонете пералнята за да отстраните подсилващите опаковъчни материали като издърпате опаковъчната лента.

Отваряне на болтовете за транспортиране

AБолтовете за обезопасяване при транспортиране трябва да бъдат свалени преди работа с пералната машина! В противен случай ще повредите пералнята!

1.Разхлабете винтовете с гаечен ключ докато започнат да се въртят свободно

(“C”)

2.Отстранете винтовете за обезопасено пренасяне като ги развиете внимателно.

3.Наместете капачките (намират се в пакета с упътването) в дупките от винтовете на задния панел. (“P”)

C Съхранявайте болтовете за обезопасено транспортиране, за да може да ги ползвате отново ако се налага пренасяне на пералнята в бъдеще.

C Никога не пренасяйте пералнята без да сте завили правилно болтовете по местата им!

Регулиране на крачетата

AНе използвайте никакви уреди за разхлабване на контрагайките. В противен случай може да ги повредите!

1.Разхлабете ръчно (с ръка) контрагайките на крачетата.

2.Нагласете ги така, че пералнята да бъде нивелирана и стабилна.

3.Важно: Затегнете отново всички контрагайки.

•За да се избегнат течове, които могат да възникнат по местата на свръзка, са осигурени гумени уплътнители (4

уплътнителя за моделите с двойно водно захранване и 2 уплътнителя за другите модели), закрепени към маркучите. Тези уплътнители се поставят на двата края на маркуча, откъм крана и откъм пералнята. Правият накрайник на маркуча, оборудван с филтър, се свързва с крана, а кривият накрайник се свързва с пералнята. Затегнете добре гайките на маркуча с ръка; никога не използвайте гаечен ключ за завиването им.

•Моделите с единично водно захранване не се свързват с кран с топла вода.

Когато връщате уреда на мястото му след ремонт или почистване, трябва да внимавате да не прегънете, притиснете или блокирате маркучите.

Свързване към отводнителната система

Маркучът за изходящата вода може да се прикрепи към страничната стена на кухненска мивка или вана. Изходящият маркуч трябва да се закрепи стабилно в отводнителната тръба за да не се изскубне от гнездото си.

Важно:

•Накрайникът на изходящия маркуч трябва да е свързан директно с канала за мръсна вода или мивката.

•Маркучът трябва да се инсталира на наймалко 40 см и най-много 100 см височина.

•В случай, че маркучът е повдигнат след като е поставен на нивото на земята (помалко от 40см над земята), източването на водата се затруднява и прането може да остане мокро.

Свързване към водното захранване

Важно:

• Необходимото водно налягане за работа на пералнята трябва да е 1-10 бара (0,1 – 1 мегапаскала).

• Свържете специалните маркучи, които се доставят заедно с пералната машина, към входящите отвори за водно захранване, разположени върху пералнята.

• Поне 15см от маркуча трябва да се намират в отводната тръба. Ако е твърде дълъг, може да го скъсите.

• Максималната дължина на свързаните

15 - BG