Loading...
iMac 24-inch VESA Mount Adapter
iMac 24-inch VESA Mount Adapter
With the VESA Mount Adapter installed, you can use your 24-inch iMac with a variety of VESA-compliant mounting solutions, such as articulating arms or wall mounts. Use the adapter only with a VESA mount that can support the weight of your 24-inch iMac.
Your VESA Mount Adapter Kit contains:
ÂA mount adapter
ÂA flange
Â1 screw
Â2 bolts
ÂA hex tool
ÂA TORX tool
ÂAn access card
You’ll also need a soft cloth and a flat work surface.
Installing the VESA Mount Adapter on Your 24-inch iMac
Follow these instructions to install the mount adapter on the back of your 24-inch iMac. You can then attach your iMac to a VESA-compliant mounting solution.
To install the mount adapter:
1 Turn off your iMac and disconnect the power cord and all cables.
3
2Turn your iMac so that the back is facing you, and then rotate the top forward until it won’t go any further.
3Release the latch by inserting the access card in the space directly above the top of the stand.
The access card should go into the space at a slight upward angle for about 3/4 of an inch. If it goes in farther, you’ve missed the latch, so try again.
Access card
4English
Important: Use only the access card provided with the kit for this step. Use of any other object or instrument could result in personal injury, and damage to your iMac. If your access card has become lost or damaged, go to www.apple.com/support/imac/ diy/vesa to purchase a replacement access card.
4Rotate your iMac forward another 10 degrees until the 8 screws on top of the stand are visible and the stand is locked in place.
Important: Keep your iMac upright until the stand is locked in place.
5Hold the sides of your iMac and carefully lay it down so that the screen is resting on a soft towel or cloth on a flat surface and the stand hangs over the edge of your work surface.
English |
5 |
|
|
6Use the TORX tool to remove the 8 screws that attach the stand to the back of your iMac. You’ll need these screws to attach the flange to your iMac, so set them aside.
TORX tool |
Hex tool |
7 Remove the stand and put it in a safe place in case you want to reattach it.
TORX tool
6English
8Align the hole in the flange with the pin on the back of your iMac, and then use the TORX tool and the 8 screws you removed from the stand to attach the flange.
Hole
Flange 
Pin
English |
7 |
|
|
9Place the mount adapter over the flange.
Important: Keep the flange in the locked position while you attach the mount adapter.
8English
10Use the TORX tool to screw the screw into the top of the mount adapter, and then use the hex tool and the two bolts to attach the mount adapter to the back of your iMac.
Bolt |
Screw |
Bolt |
11Follow the instructions included with the VESA-compliant mounting solution to attach it to your 24-inch iMac.
12Connect the power cord and cables to your iMac.
English |
9 |
|
|
10
11
12
13
14
9 
15
10 
11
12
16
Adaptateur de monture VESA Mount Adapter de l’iMac 24 pouces
Une fois l’adaptateur de monture VESA Mount Adapter installé, vous pouvez utiliser plusieurs solutions de montage conformes VESA avec votre iMac 24 pouces, telles qu’un bras articulé ou un emplacement mural. Utilisez cet adaptateur uniquement avec une monture VESA qui peut supporter le poids de votre iMac 24 pouces.
Votre kit d’adaptateur de monture VESA Mount Adapter contient :
Âun adaptateur de monture ;
Âune collerette ;
Âune vis ;
Âdeux boulons ;
Âune clé hexagonale ;
Âune clé Torx ;
Âune carte d’accès.
Vous aurez également besoin d’un tissu doux et d’une surface de travail plane.
17
Installation de l’adaptateur de monture VESA Mount Adapter sur votre iMac 24 pouces
Suivez ces instructions pour installer l’adaptateur de monture à l’arrière de votre iMac 24 pouces. Vous pourrez ensuite fixer votre iMac à une solution de montage conforme VESA.
Pour installer l’adaptateur de monture :
1 Éteignez votre iMac puis débranchez le câble d’alimentation et tous les autres câbles.
2Tournez votre iMac de manière que l’arrière vous fasse face, puis faites pivoter le haut vers l’avant jusqu’à ce qu’il ne puisse aller plus loin.
3Déverrouillez le loquet en insérant la carte d’accès dans l’ouverture située juste au-des- sus du support.
18 Français
Loading...