Acer ACP45 USB PORT REPLICATOR User Manual

0 (0)

port

Replicator

Table of Contents

Acer Port Replicator .............................................................3

Acer Anschlusswiederholer / Acer Port Replicator .............22

Acer Replicador de Puerto ..................................................44

Acer Duplicateur de Port .....................................................65

Acer Replicatore di Porte ....................................................87

Acer Poortreplicator ..........................................................108

Acer Ficha de Replicador ................................................. 129

English

Deutsch

Español

Français

Italiano

Nederlands

Português

ACER PORT

REPLICATOR

Introduction

Congratulations on your purchase of the Acer Port

Replicator. This portable expansion module allows you to

connect through a single USB connection up to 4 USB

devices, a network (Ethernet/LAN) connection, speakers

and microphone, PS/2 mouse and keyboard, a serial and

a parallel device. Also, the slot lock and the universal lock

support provided help you secure your docking station to

your desktop.

The port replicator also features Always On technology,

USB Power Port providing twice the USB specification for

higher power requirement devices, and USB ports that

are widely spaced to accommodate larger adapters.

Always On provides power to the USB ports even when

the notebook is shut-down, disconnected from the

docking station or in hibernate/stand-by mode. This

allows USB devices that charge via the USB port to keep

charging under any circumstance.

Features

Heat dissipation by natural convection:

Place the back edge of your laptop on the rubber pads of

the Port Replicator. Most laptops dissipate heat through

the bottom and the more air that’s allowed to flow under

the bottom, the better chance that heat will dissipate by

natural convection.

Acer Port Replicator

Comfort

The raised platform provides a more comfortable position

for the hands, and increased airflow for better cooling.

The Port Replicator provides the following ports:

• Two PS/2 ports

• IEEE 1284 DB25 Connector parallel

• Two 3.5 mm Audio: (1) stereo out and (1) microphone

• RS232 serial

• One S/PDIF Digital Audio Output

• RJ-45 Ethernet 10/100

• Two USB 2.0 (White)

• Two USB Power Ports (the two right most ports on the

back of the device) - Providing up to 1Amp of power per

port

Package Contents

In addition to this user guide, the package contains:

• Acer Port Replicator

• High-speed USB 2.0 upstream cable

• Driver software CD

• AC power adapter (Required)

Acer Port Replicator

System

Requirements

Hardware

• PC with an Intel

Pentium

processor or equivalent

• CD-ROM drive

• USB version 2.0port

• AC power source (AC adapter required)

NOTE: W

HEN CONNECTED TO A USB VERSION 1.1 PORT ON YOUR

COMPUTER

, THE PORT REPLICATOR’S PERFORMANCE LEVEL WILL BE LESS THAN

OPTIMAL

.FOR BEST RESULTS, CONNECT IT TO A USB VERSION 2.0 PORT.

Operating System

• Windows

2000 Service Pack 4

• Windows

NOTE: T

O DOWNLOAD THE LATEST SERVICE PACKS, PLEASE VISIT YOUR

COMPUTER

MANUFACTURER

’S WEBSITE OR MICROSOFT’S DOWNLOAD CENTER:

http://support.microsoft.com/default.aspx?scid=fh%3BEN-

US%3Bsp

Installing the

Device and Drivers

To use the Acer Port Replicator, you must first install the

driver onto your computer.

WARNING: Y

OU MUST INSTALL THE PORT REPLICATOR SOFTWARE BEFORE

CONNECTING IT TO YOUR COMPUTER. OTHERWISE, THE PORT REPLICATOR WILL

NOT WORK PROPERLY

• Windows Vista

Acer Port Replicator

After installing your software, connect the port replicator

to your computer and Windows plug-and-play will install

the hardware drivers for each port.

Installing the Port

Replicator Driver

Installing the port replicator driver enables your operating

system to recognize it and its ports once it’s connected.

1 Turn on your computer.

2 Insert the driver software CD into your computer’s

CD-ROM drive.

If setup does not begin automatically, click Start, Run,

and enter D:\Setup.exe (where D: is the path of your

CD-ROM drive) and then click OK.

3 The Installation Wizard window of the port replicator

will pop up. Click Next to proceed.

Acer Port Replicator

4 The Information window will pop up. Click Next to

proceed. In order to install the driver files properly,

you must restart your system before plugging in

the Port Replicator.

5 Choose Yes, I want to restart my computer now.

Click Finish and restart your computer when

prompted.

Acer Port Replicator

Connecting the Port

Replicator to Your

Computer

After installing the port replicator software, you are ready

to connect the port replicator to your computer. To do

this:

1 Connect the supplied AC power adapter to the AC

power jack on the port replicator.

2 Connect one end of the USB cable to the port

replicator and the other end into an available USB 2.0

port on your computer.

WARNINGS: T

HE PORT REPLICATOR WILL NOT FUNCTION PROPERLY

WITHOUT

THE

AC ADAPTER PLUGGED INTO AN AC OUTLET.

O NOT CONNECT ANY DEVICES TO THE PORT REPLICATOR UNTIL THE

INSTALLATION IS COMPLETED

Installing the

Default Device

Drivers

Once you connect the port replicator to your computer,

the default drivers begin installing for each of the ports

automatically.

NOTE: P

LEASE ENSURE YOU HAVE THE LATEST SERVICE PACKS INSTALLED

Some hardware devices may prompt you to install the

drivers.

To install the drivers:

Acer Port Replicator

1 Select Install the software automatically

(Recommended) and click Next.

The Found New Hardware Wizard program begins

installing the hardware drivers.

The Completing the Found New Hardware Wizard

screen appears.

2Click Finish and repeat as needed for each device.

3 Restart your computer.

LED Status Indicator

Lights

Once all device drivers are installed, the USB LED status

indicator lights on the back of the port replicator glow

when you connect devices to the port replicator.

• Green Tx light illuminates when connected to a

network and the yellow Rx light flashes when data is

transmitting to or from the network.

NOTE: T

HE PORT REPLICATOR SUPPORTS HOT SWAPPING OF THE NETWORK

CABLE

Acer Port Replicator

Port Replicator ports

Port Replicator Left-Sided View

Port Replicator Right-Sided View

Lock (not included)

“Easy Access”

USB Port

Audio In Audio Out

Serial

S/PDIF

Network

USB Power Port

Parallel

PS/2

USB Port

Cable Lock Slot

USB to PC

Connection

AC Ada pter

Laptop Support Pad

Acer Port Replicator

Connecting New

Devices

To avoid possible damage when connecting a new

device, do not force the cable connector into the port on

the port replicator. If the cable connector does not attach

smoothly, turn the connector over and try attaching it

again.

Connecting a Serial

Mouse / Keyboard

To connect a serial mouse or keyboard, attach the cable

connector to the serial port on the port replicator.

Connecting a PS/

Mouse / Keyboard

To connect a PS/2 mouse or keyboard, attach the cable

connector to the PS/2 port on the port replicator.

Connecting and

Configuring a Serial

Modem

To connect a serial modem:

1 Attach the cable connector to the serial port on the

port replicator.

2 Install the modem software driver according to the

instructions that come with the device.

3 When prompted to select the port, choose the Serial

USB (COMx), where x is the COM port number

assigned by your operating system.

Acer Port Replicator

Connecting a Parallel

Printer

To connect a parallel printer:

1 Attach the cable connector to the parallel port on the

port replicator.

2 Go to Start button of your Window OS, and click on

Printers and Faxes. Add your printer driver by

following the instructions of the Add Printer Wizard.

Connecting a PDA

1 Attach the cable connector to the serial port on the

port replicator.

2 Verify that the COM port setting, in either your

HotSync

or ActiveSync

software, matches the

setting on the port replicator.

To verify the COM port setting on the port replicator,

refer to “Verifying Devices are Installed” on page 18.

To verify the COM port setting on your PDA, refer to

the documentation that came with it.

Connecting to a Local

Area Network

To connect an Ethernet cable with an RJ-45 connector,

attach the cable connector to the Ethernet/network port

on the port replicator. Additional procedures to connect to

an actual network depend on the type of network you are

using. Contact your network administrator for detailed

instructions.

Acer Port Replicator

Connecting a USB

Device

To connect a USB device, plug it into a USB port on the

port replicator and follow the additional instructions

provided with the device.

All four USB ports meet USB High-speed requirements

by providing 480Mbps and 500mA of power. However,

the two most right-sided USB ports have two unique

features. See “Always On” on page 16 for more details,

and “Using USB Devices That Require More Power” on

page 16

The white USB ports, located one on the side and the

other on the back next to the Ethernet port, are high-

speed ports that provide standard 500mA of power. The

other two USB ports, on the back next to the wired cable

lock slot, are also high-speed ports that provide up to

1Amp of power each They can be used to power USB

devices, such as hard drives, printers, and external

optical devices, that draw more power than a standard

USB port supplies.

Connecting and

Configuring an Audio

Device

1 Plug your headphones or speakers into the green

3.5mm Audio Out port on the port replicator.

2 To connect a microphone, plug it into the mono Audio

In port.

3 To enable your headphones or speakers, you must

first choose C-Media USB Sound Device in the

Properties Settings.

Acer Port Replicator

Universal DockingStation

Digital Decoder

A/V Receiver

Optical Cable (Not included)

Home Theatre

ZOOM IN

For Windows

2000, click Start, Settings, Control

Panel, and then open the Sounds and Multimedia

folder. Select the Audio tab. Under Sound Playback,

change Preferred Device to C-Media USB Sound

Device from the drop down list.

Click Apply, then click OK.

For Windows

XP, go to the Control Panel and choose

Sound and Audio. Select the Audio tab. Under Sound

Playback, change Preferred Device to C-Media USB

Sound Device from the drop down list.

Click Apply, then click OK.

4 Make sure the volume is not set to MUTE.

NOTE: A

UDIO DEVICES WILL NOT WORK SIMULTANEOUSLY ON THE PORT

STATION AND THE HOST COMPUTER

CAUTION: A

LL AUDIO OR MULTIMEDIA APPLICATIONS MUST BE TERMINATED

BEFORE

SWITCHING BETWEEN THE PORT STATION AUDIO OUTPUT AND THE

HOST COMPUTER AUDIO OUTPUT

Acer Port Replicator

Installing and

Configuring a S/PDIF

(Sony/ Philips Digital

Interface) Device

1 In order to enable S/PDIF, you have to turn it on. This

can be done by opening the USB 3D Sound

Configuration applet located in your system tray (click

on the USB icon to open up the Configuration Screen

2 Click on the button next to the S/PDIF Output text to

enable S/PDIF

3 Set the Audio Output from the Tray

Acer Port Replicator

4 Plug your optical cable (not included) into the

S/PDIF-Out port of Port Replicator on one end, and

the S/PDIF-In port of Digital Decoder or Speaker on

the other end.

5 Connect your Digital Decoder or Speaker to the Home

Theater System.

Global Suspend

Mode

When your computer is in suspend mode, the port

replicator also enters suspend mode to avoid power

consumption. When your computer wakes up, the port

replicator wakes up automatically.

Always On

The two USB ports that provide up to 1Amp of power will

continue providing power even when the laptop is

powered down or disconnected from the port replicator.

This allows you to charge any USB device you may have

connected.

Using USB Devices

That Require More

Power

Some devices, which use large amounts of power, such

as printers and optical drives, should be plugged into the

High Power USB Ports. These ports will provide up to

1000mA of power - double the power of a standard USB

ports.

Acer Port Replicator

Product

Limitations

Some devices may halt temporarily when a high data

transfer is occurring. For example, your mouse may

respond slowly while a graphic print job is printing or

while you are experiencing heavy network traffic.

We recommend the following guidelines:

• Do not transfer data to or from multiple high-speed

devices, such as a digital camera or scanner, at the

same time.

• If speed degradation does occur, close other programs

that use a USB device to improve device performance.

Troubleshooting

Device Not Working

• Make sure that the device is fully inserted into the

correct port on the port replicator.

• Plug the device into a different port on the port

replicator. If it still doesn’t work, test the device by

connecting it directly to your computer.

• Verify that you ran the Setup or Install program for the

device.

• Make sure that the device appears in Device Manager.

For more information refer to “Verifying Devices are

Installed” on page 18.

• Disconnect all devices from the port replicator and

reconnect them, one at a time. Check that each device

works before plugging in the next one.

Acer Port Replicator

• Each USB port is equipped with over-current

protection. Should a USB device draw more current

than the USB port can supply, the port will shut down.

To re-enable the port, unplug the device and go to

Device Manager or to the message in the system tray

and choose the Reset option. You can then plug the

device back into the USB port. If a shut down reoccurs,

check the power requirements of the device.

Verifying Devices are

Installed

You can view the devices installed on the port replicator

from the Device Manager window in System Properties.

Right-click My Computer, Properties, then click the

Hardware tab, and then the Device Manager button.

From the Device Manager window, expand the following:

• Human Interface Devices - displays keyboards and

pointing devices: mice, trackballs, and joysticks

• Keyboards — displays PS/2 keyboards

• Mice and Other Pointing Devices - displays PS/2

mouse

• Network Adapters — displays ASIX AX88772 USB 2.0

fast Ethernet Adapter

• Ports (COM & LPT) — Prolific USB-to-Serial Comm

Port (COM X)

• Sound, Video and Game Controllers — displays

C-Media USB sound device

• Universal Serial Bus controllers — displays the other

devices installed for the port replicator and generic hub

Acer Port Replicator

Verifying a Serial

Modem Connection

When attaching a modem to the serial (RS232) port,

verify that the port assigned to your modem is Serial USB

(COMx), where x is the number of the COM port.

If the operating system does not detect automatically that

your modem is assigned to Serial USB (COMx), run the

Hardware Wizard again and choose Select from the list

instead of Autodetect. Then, select use Prolific Device

from Page as the COM port.

Error Message on

Your PDA

If the error message “Connection Not Established”

appears on your PDA, check that the COM port setting in

either your HotSync or ActiveSync software matches the

setting on the port replicator. See “Verifying Devices are

Installed” on page 18 to verify the COM port setting on

the port replicator.

Some older versions of the Palm

Desktop software are

not compatible with the USB to Serial conversion. Please

contact your PDA vendor for software updates.

Technical Support

For more information about out products, services, and

support information, please visit our website:

Internet: http://global.acer.com

http://support.acer-euro.com/emea.html

Acer Port Replicator

Regulatory

Compliance

This device complies with Part 15 of the FCC Rules. Operation is

subject to the following two conditions: (1) This device may not

cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause

undesired operation.

FCC Statement

Tested to Comply

This equipment has been tested and found to comply with the

limits of a Class B digital device, pursuant to Part 15 of the FCC

Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This

equipment generates, uses, and can radiate radio frequency

energy and if not installed and used in accordance with the

instructions, may cause harmful interference to radio

communications. However, there is no guarantee that interference

will not occur in a particular installation.

If this equipment does cause harmful interference to radio or

television reception, which can be determined by turning the

equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

• Reorient or relocate the receiving antenna;

• Increase the separation between the equipment and receiver;

• Connect the equipment into an outlet on a circuit different from

that to which the receiver is connected;

• Consult the dealer or experienced radio/TV technician for help.

Changes or modifications not authorized by the party responsible

for compliance could void the user’s authority to operate this

product.

Acer Recycling Directive

Acer products are marketed worldwide and we recognize our

global responsibility for the final disposal of Acer products. We

actively participate in waste product recycling and treatment

Acer Port Replicator

systems wherever our products are sold according to WEEE

Directive and local regulations or recycling programs.

http://global.acer.com/about/sustainability14.htm

Acer and the Acer logo are registered trademarks of Acer Incorporated. Other

company’s product names or trademarks are used hereinforidentification purposes

only and belong to theirrespective companies.

Changes may be made periodically to the information inthispublication without

obligation to notify any person of such revision or changes. Such changes will be

incorporated inneweditions of this manual or supplementary documents and

publications. This company makes no representationsor warranties, either expressed or

implied, with respect to the contents hereof and specifically disclaims the impl

ied

warranties of merchantability or fitness for a particular purpose.

Record the model number, serial number, and place of purchase information inthe

space provided below. The serial number and model number are recorded on the label

affixedtoyourcomputer. All correspondence concerning your unitshouldinclude the

serial number, model number, and purchase information.

No part of thispublication may be reproduced, stored in a retrieval sy stem, or

transmitted, in any form or by any means, electronic, mechanical, photocopy, recording,

or otherwise, without the prior written permission of Acer Incorporated.

Acer Port Replicator

Model Number:

Serial Number:

Purchase Date:

Place of Purchase:

Acer Port Replicator User’sGuide.

Original Issue: July 2006

Palm and HotSync are a registered trademarks of Palm, Inc. Microsoft, Windows,

ActiveSync and Windows Vista are either registered trademarks or trademarks of

Microsoft Corporation in the United States and/or other countries. All trademarks and

ACER

ANSCHLUSSWIE

DERHOLER /

ACER PORT

REPLICATOR

Einführung

Herzlichen Glückwunsch zum Kauf der

Anschlusswiederholer von Acer. Mit Hilfe dieses

tragbaren Erweiterungsmoduls können Sie über einen

einzelnen USB-Anschluss bis zu vier USB-Geräte,

Lautsprecher und Mikrofon, PS/2-Maus und -Tastatur, ein

serielles und ein paralleles Gerät anschließen sowie eine

Netzwerkverbindung (Ethernet/LAN) herstellen. Ein

Kabel- und ein Universalschloss bieten zudem die

Möglichkeit, die Anschlusswiederholer an einem

Schreibtisch zu sichern.

Ferner verfügt die Anschlusswiederholer über die

Always-On-Technologie, einen Acer USB-Power-Port mit

doppelter USB-Spezifikation für Geräte mit höherem

Versorgungsbedarf, und USB-Ports, die genügend Platz

für den Anschluss größerer Adapter bieten. Die Always-

On-Technologie versorgt die USB-Ports auch dann, wenn

das Notebook ausgeschaltet ist, von der

Anschlusswiederholer abgetrennt ist oder sich im

Ruhezustand / Standby-Modus befindet. So können

Acer Anschlusswiederholer / Acer Port Replicator

USB-Geräte. die über den USB-Port versorgt werden, in

jeder Situation aufgeladen werden.

Merkmale

Wärmeableitung durch natürliche Konvektion:

Stellen Sie die Hinterkante Ihres Laptops auf die

Gummipuffer der Anschlusswiederholer. Bei den meisten

Laptops wird die Wärme über die Unterseite abgeleitet.

Je mehr Luft daher an die Unterseite gelangen kann,

desto besser kann die Wärme durch natürliche

Konvektion abgeleitet werden.

Komfort

Die angehobene Plattform ermöglicht eine bequemere

Handhaltung und sorgt für eine bessere Kühlung.

Die Anschlusswiederholer verfügt über folgende Anschlüsse:

• zwei PS/2-Ports

• ein paralleler IEEE 1284 DB25-Anschluss

• zwei 3,5-mm-Audioanschlüsse: ein Stereoausgang und

ein Mikrofoneingang

• ein serieller RS232-Anschluss

• ein digitaler S/PDIF-Audioausgang

• ein RJ45 Ethernet 10/100-Anschluss

• zwei USB 2.0-Anschlüsse (weiß)

• zwei USB-Power-Ports (die beiden äußersten rechten

Ports auf der Rückseite) - max. 1 A Leistung pro Port

Acer Anschlusswiederholer / Acer Port Replicator

Lieferumfang

Zusätzlich zu diesem Benutzerhandbuch umfasst der

Lieferumfang:

• Acer Universal-Anschlusswiederholer

• High-Speed USB 2.0 Upstream-Kabel

• Tr e ibersoftware-CD

• Netzstromadapter (erforderlich)

Systemvorausset

zungen

Hardware

• PC miteinem Intel® Pentium® oder entsprechenden

Prozessor

• CD-ROM-Laufwerk

• USB 2.0-Port

• Netzstromquelle (Netzadapter erforderlich)

HINWEIS: BEIM ANSCHLUSS AN EINEN USB 1.1-PORT IHRES

COMPUTERS ERREICHT DIE ANSCHLUSSWIEDERHOLER NICHT DIE

OPTIMALE LEISTUNG. FÜR OPTIMALE RESULTATE SCHLIESSEN SIE

SIE AN EINEN USB 2.0-PORT AN.

Betriebssystem

• Windows® 2000 Service Pack 4

• Windows® XP

HINWEIS: UM SICH DIE NEUESTEN SERVICEPACKS

HERUNTERZULADEN, BESUCHEN SIE BITTE DIE WEBSITE IHRES

• Windows Vista

Acer Anschlusswiederholer / Acer Port Replicator

COMPUTERHERSTELLERS ODER DAS MICROSOFT DOWNLOAD-

CENTER:

http://support.microsoft.com/default.aspx?scid=fh%3BEN-

US%3Bsp

Installieren des

Geräts und der

Treiber

Bevor Sie die Targus Dockingstation benutzen können,

müssen Sie zunächst den Treiber auf Ihrem Computer

installieren.

WARNUNG: SIE MÜSSEN DIE SOFTWARE FÜR DIE

DOCKINGSTATION INSTALLIEREN, BEVOR SIE DIESE AN IHREN

COMPUTER ANSCHLIESSEN. ANDERNFALLS FUNKTIONIERT DIE

DOCKINGSTATION NICHT EINWANDFREI.

Nach dem Installieren der Software schließen Sie die

Dockingstation an Ihren Computer an. Durch die

Windows Plug-and-Play-Funktion werden die Treiber für

jeden Port installiert.

Installieren des

Treibers für die

Dockingstation

Durch das Installieren des Treibers kann Ihr

Betriebssystem die Dockingstation und ihre Ports nach

dem Anschließen erkennen.

1 Schalten Sie Ihren Computer ein.

2 Legen Sie die Treibersoftware-CD in das CD-ROM-

Laufwerk Ihres Computers ein.

Acer Anschlusswiederholer / Acer Port Replicator

Sollte die Einrichtung nicht automatisch beginnen,

klicken Sie auf Start, Ausführen, und geben dann

D:\Setup.exe ein (wobei D: der Pfad zu Ihrem CD-ROM-

Laufwerk ist), und klicken dann auf OK.

3 Das Fenster mit dem Installationsassistenten für die

Anschlusswiederholer erscheint. Klicken Sie auf Next

(Weiter),um fortzufahren.

4Das Informationsfenster erscheint. Klicken Sie auf

Next, um fortzufahren. Damit die Treiberdateien

Acer Anschlusswiederholer / Acer Port Replicator

korrekt installiert werden, müssen Sie Ihr System

neu starten, bevor Sie die Anschlusswiederholer

anschließen.

5 Wählen Sie Yes (Ja), um den Computer jetzt neu zu

starten. Klicken Sie auf Finish (Fertig stellen), und

starten Sie Ihren Computer, wenn die Aufforderung

erfolgt.

Schlieen Sie die

Anschlusswiederhole

r an Ihren Computer an

Nach dem Installieren der Anschlusswiederholer-

Software können Sie die Anschlusswiederholer an Ihren

Computer anschließen. Dazu tun Sie Folgendes:

1 Schließen Sie den mitgelieferten Netzstromadapter

an der Netzbuchse der Anschlusswiederholer an.

2 Schließen Sie ein Ende des USB-Kabels an der

Anschlusswiederholer und das andere Ende an einem

freien USB 2.0-Port Ihres Computers an.

Acer Anschlusswiederholer / Acer Port Replicator

WARNUNG: DIE ANSCHLUSSWIEDERHOLER FUNKTIONIERT NUR

EINWANDFREI, WENN DER NETZSTROMADAPTER AN EINER

STECKDOSE ANGESCHLOSSEN IST.

SCHLIESSEN SIE ANDERE GERÄTE ERST AN DER

ANSCHLUSSWIEDERHOLER AN, WENN DIE INSTALLATION

ABGESCHLOSSEN IST.

Installieren der

standardmäigen

Gerätetreiber

Nachdem Sie die Anschlusswiederholer an Ihren

Computer angeschlossen haben, werden automatisch

die standardmäßigen Treiber für jeden der Ports

installiert.

HINWEIS: ACHTEN SIE BITTE DARAUF, DIE NEUESTEN

SERVICEPACKS ZU INSTALLIEREN

Manche Geräte fordern dazu auf, die Treiber zu

installieren.

So installieren Sie die Treiber:

1 Wählen Sie Software automatisch installieren

(empfohlen), und klicken Sie dann auf Weiter.

Der Assistent für neue Hardware beginnt nun damit,

die Gerätetreiber zu installieren.

Anschließend erscheint der Abschlussbildschirm des

Hardwareassistenten.

2 Klicken Sie auf Fertig stellen, und wiederholen Sie

die Schritte für jedes Gerät.

3 Starten Sie Ihren Computer neu.

Acer Anschlusswiederholer / Acer Port Replicator

LED-Statusanzeigen

Nachdem alle Gerätetreiber installiert sind, leuchten die

USB-Status-LEDs auf der Rückseite der

Anschlusswiederholer auf, wenn Geräte angeschlossen

werden.

• Die grüne Tx-LED leuchtet beim Anschluss an ein

Netzwerk, und die gelbe Rx-LED blinkt, wenn Daten

zum oder vom Netzwerk übertragen werden.

HINWEIS: DIE ANSCHLUSSWIEDERHOLER UNTERSTÜTZT EIN "HOT

SWAPPING" DES NETZWERKKABELS.

Acer Anschlusswiederholer / Acer Port Replicator

Ports an der Anschlusswiederholer

Linke Seite der Anschlusswiederholer

Rechte Seite der Anschlusswiederholer

Laptopauflage

Audioeingang

Audioausgang

Seriell

S/PDIF

Netzwerk

USB-Port

USB-Power-Port

PS/2

Parallel

Kabelsicherung

“Easy Access”

USB-Port

(nicht enthalten)

Netzstromadapter

USB-zu-PC Anschl

Kabelsicherung

+ 120 hidden pages