T8D
Table of contents
Loading...
F6D
F8D
T8D
OWNER’S MANUAL
LIT-18626-05-98
60R-F8199-10
U.S.A.Edition
ZMU01690
Read this owner’s manual carefully before operating your outboard motor.
Important manual information
EMU25100
To the owner
Thank you for choosing a Yamaha outboard
motor. This Owner’s Manual contains infor-
mation needed for proper operation, mainte-
nance and care. A thorough understanding of
these simple instructions will help you obtain
maximum enjoyment from your new Yamaha.
If you have any question about the operation
or maintenance of your outboard motor,
please consult a Yamaha dealer.
In this Owner’s Manual particularly important
information is distinguished in the following
ways.
The Safety Alert Symbol means AT-
TENTION! BECOME ALERT! YOUR SAFE-
TY IS INVOLVED!
WARNING
EWM00780
Failure to follow WARNING instructions
could result in severe injury or death
to the
machine operator, a bystander, or a per-
son inspecting or repairing the outboard
motor.
CAUTION:
ECM00700
A CAUTION indicates special precautions
that must be taken to avoid damage to the
outboard motor.
NOTE:
A NOTE provides key information to make
procedures easier or clearer.
Yamaha continually seeks advancements in
product design and quality. Therefore, while
this manual contains the most current product
information available at the time of printing,
there may be minor discrepancies between
your machine and this manual. If there is any
question concerning this manual, please con-
sult your Yamaha dealer.
NOTE:
The F6MH, F8MH, T8PH, T8EH, T8PR and
the standard accessories are used as a base
for the explanations and illustrations in this
manual. Therefore some items may not apply
to every model.
EMU25130
F6D, F8D, T8D
OWNER’S MANUAL
©2004 by Yamaha Motor Corporation,
USA
1st Edition, January 2004
All rights reserved.
Any reprinting or unauthorized use
without the written permission of
Yamaha Motor Corporation, USA
is expressly prohibited.
Printed in France
P/N LIT-18626-05-98
Table of contents
General information ......................1
Identification numbers record...... 1
Outboard motor serial number ....... 1
Key number.................................... 1
Emission control information ....... 1
North American models.................. 1
Star labels ...................................... 2
Safety information ....................... 3
Important labels........................... 4
Warning labels................................ 4
Caution labels................................. 5
Basic boating rules
(Rules of the road) ................... 5
Steering and sailing rules and
sound signals.............................. 5
Rules when encountering
vessels........................................ 6
Other special situations .................. 7
Fueling instructions ..................... 9
Gasoline ....................................... 10
Engine oil...................................... 10
Battery requirement................... 10
Battery specifications ................... 11
Without a rectifier or Rectifier
Regulator .................................. 11
Propeller selection..................... 11
Start-in-gear protection ............. 12
Basic components ...................... 13
Main components ...................... 13
Fuel tank....................................... 14
Fuel joint....................................... 15
Fuel gauge ................................... 15
Fuel tank cap................................ 15
Air vent screw............................... 15
Remote control............................. 15
Remote control lever .................... 15
Neutral interlock trigger ................ 16
Neutral throttle lever..................... 16
Choke switch................................ 16
Tiller handle.................................. 16
Gear shift lever............................. 16
Throttle grip .................................. 17
Throttle indicator........................... 17
Throttle friction adjuster................ 17
Engine stop lanyard switch........... 18
Engine stop button ....................... 18
Choke knob for pull type............... 19
Manual starter handle................... 19
Starter button................................ 19
Main switch................................... 19
Power tilt switch............................ 19
Steering friction adjuster............... 20
Trim rod (tilt pin) ........................... 20
Tilt lock mechanism...................... 21
Tilt support knob........................... 21
Tilt support bar ............................. 21
Power tilt unit................................ 21
Top cowling lock lever
(pull up type) ............................. 21
Flushing device ............................ 22
Warning indicator ......................... 22
Low oil pressure warning
indicator .................................... 22
Warning system ........................ 23
Low oil pressure warning .............. 23
Operation ..................................... 24
Installation................................. 24
Mounting the outboard motor ....... 24
Clamping the outboard motor ....... 25
Breaking in engine .................... 26
Procedure for 4-stroke models ..... 26
Preoperation checks ................. 26
Fuel .............................................. 26
Controls ........................................ 26
Engine .......................................... 27
Checking the engine oil level........ 27
Filling fuel.................................. 27
Ring Free Fuel Additive................ 27
Operating engine ...................... 28
Feeding fuel (portable tank) ......... 28
Starting engine ............................. 29
Warming up engine................... 32
Manual start models..................... 32
Shifting ...................................... 33
Table of contents
Forward (tiller handle and remote
control models) ......................... 33
Reverse (manual tilt and hydro tilt
models) ..................................... 34
Stopping engine ........................ 35
Procedure..................................... 35
Procedure..................................... 35
Trimming outboard motor .......... 36
Adjusting trim angle for manual tilt
models ...................................... 36
Adjusting trim angle
(power tilt models)..................... 37
Adjusting boat trim........................ 38
Tilting up and down ................... 38
Procedure for tilting up
(manual tilt models)................... 39
Procedure for tilting up................. 40
Procedure for tilting down
(manual tilt models)................... 40
Procedure for tilting down............. 41
Cruising in shallow water .......... 41
Cruising in shallow water
(manual tilt models)................... 41
Power trim and tilt models /
power tilt models....................... 43
Cruising in other conditions ....... 44
Maintenance.................................45
Specifications ............................ 45
Transporting and storing
outboard motor....................... 46
Clamp screw mounting models .... 47
Storing outboard motor................. 47
Procedure..................................... 48
Lubrication (except oil injection
models) ..................................... 49
Cleaning and anticorrosion
measures .................................. 49
Battery care.................................. 49
Flushing power unit ...................... 50
Cleaning the outboard motor ........ 51
Checking painted surface of
motor......................................... 51
Periodic maintenance................ 51
Replacement parts ....................... 51
Maintenance chart........................ 52
Maintenance chart (additional) ..... 53
Greasing....................................... 54
Cleaning and adjusting
spark plug ................................. 55
Checking fuel system ................... 55
Checking fuel filter........................ 56
Inspecting idling speed ................. 56
Changing engine oil...................... 57
Checking wiring and
connectors ................................ 58
Exhaust leakage........................... 58
Water leakage .............................. 59
Engine oil leakage........................ 59
Checking power trim and
tilt system .................................. 59
Checking propeller ....................... 59
Removing the propeller ................ 60
Installing the propeller .................. 61
Changing gear oil ......................... 61
Cleaning fuel tank......................... 62
Inspecting and replacing
anode(s).................................... 63
Checking battery
(for electric start models) .......... 63
Connecting the battery ................. 64
Disconnecting the battery............. 65
Checking top cowling ................... 65
Coating the boat bottom ............... 65
Trouble Recovery........................ 66
Troubleshooting ........................ 66
Temporary action in
emergency ............................. 69
Impact damage............................. 69
Replacing fuse.............................. 69
Power trim and tilt will not
operate...................................... 70
Starter will not operate ................. 70
Emergency starting engine........... 70
Engine fails to operate .............. 72
Ignition system malfunction .......... 72
Table of contents
Treatment of submerged
motor ...................................... 72
Procedure..................................... 72
Consumer information................ 74
Important warranty information
for U.S.A. and Canada ........... 74
YAMAHA MOTOR
CORPORATION, U.S.A.
FOUR-STROKE OUTBOARD
MOTOR THREE-YEAR
LIMITED WARRANTY ........... 76
IMPORTANT WARRANTY
INFORMATION IF YOU USE
YOUR YAMAHA OUTSIDE
U.S.A. OR CANADA .............. 78
General information
1
EMU25170
Identification numbers record
EMU25182
Outboard motor serial number
The outboard motor serial number is stamped
on the label attached to the port side of the
clamp bracket or the upper part of the swivel
bracket.
Record your outboard motor serial number in
the spaces provided to assist you in ordering
spare parts from your Yamaha dealer or for
reference in case your outboard motor is sto-
len.
EMU25190
Key number
If a main key switch is equipped with the mo-
tor, the key identification number is stamped
on your key as shown in the illustration.
Record this number in the space provided for
reference in case you need a new key.
EMU25220
Emission control information
EMU25230
North American models
This engine conforms to U.S. Environmental
Protection Agency (EPA) regulations for ma-
rine SI engines. See the label affixed to your
engine for details.
EMU25241
Approval label of emission control certifi-
cate
This label is attached to the bottom cowling.
1. Outboard motor serial number location
1. Outboard motor serial number location
1. Key number
General information
2
New Technology; (4-stroke/HPDI) EM
EMU25261
Manufactured date label
This label is attached to the clamp bracket or
the swivel bracket.
EMU25272
Star labels
Your outboard motor is labeled with a Califor-
nia Air Resources Board (CARB) star label.
See below for a description of your particular
label.
EMU25280
One Star—Low Emission
The one-star label identifies engines that
meet the Air Resources Board’s 2001 ex-
haust emission standards. Engines meeting
these standards have 75% lower emissions
than conventional carbureted two-stroke en-
gines. These engines are equivalent to the
U.S. EPA’s 2006 standards for marine en-
gines.
1. Approval label location
1. Manufactured date label location
ZMU01699
1. Star labels location
Manufactured:
ZMU04346
General information
3
EMU25290
Two Stars—Very Low Emission
The two-star label identifies engines that meet
the Air Resources Board’s 2004 exhaust
emission standards. Engines meeting these
standards have 20% lower emissions than
One Star-Low-Emission engines.
EMU25300
Three Stars—Ultra Low Emission
The three-star label identifies engines that
meet the Air Resources Board’s 2008 ex-
haust emission standards. Engines meeting
these standards have 65% lower emissions
than One Star-Low-Emission engines.
EMU25360
Safety information
● Before mounting or operating the outboard
motor, read this entire manual. Reading it
should give you an understanding of the
motor and its operation.
● Before operating the boat, read any own-
er’s or operator’s manuals supplied with it
and all labels. Be sure you understand each
item before operating.
● Do not overpower the boat with this out-
board motor. Overpowering the boat could
result in loss of control. The rated power of
the outboard should be equal to or less than
the rated horsepower capacity of the boat.
If the rated horsepower capacity of the boat
is unknown, consult the dealer or boat man-
ufacturer.
● Do not modify the outboard. Modifications
could make the motor unfit or unsafe to use.
● Never operate after drinking alcohol or tak-
ing drugs. About 50% of all boating fatalities
involve intoxication.
● Have an approved personal flotation device
(PFD) on board for every occupant. It is a
good idea to wear a PFD whenever boat-
ing. At a minimum, children and non-swim-
mers should always wear PFDs, and
ZMU01702
ZMU01703
ZMU01704
General information
4
everyone should wear PFDs when there
are potentially hazardous boating condi-
tions.
● Gasoline is highly flammable, and its va-
pors are flammable and explosive. Handle
and store gasoline carefully. Make sure
there are no gas fumes or leaking fuel be-
fore starting the engine.
● This product emits exhaust gases which
contain carbon monoxide, a colorless,
odorless gas which may cause brain dam-
age or death when inhaled. Symptoms in-
clude nausea, dizziness, and drowsiness.
Keep cockpit and cabin areas well ventilat-
ed. Avoid blocking exhaust outlets.
● Check throttle, shift, and steering for proper
operation before starting the engine.
● Attach the engine stop switch lanyard cord
to a secure place on your clothing, or your
arm or leg while operating. If you acciden-
tally leave the helm, the cord will pull from
the switch, stopping the engine.
● Know the marine laws and regulations
where you will be boating—and obey them.
For basic boating rules, see “Rules of the
road” on page 5.
● Stay informed about the weather. Check
weather forecasts before boating. Avoid
boating in hazardous weather.
● Tell someone where you are going: leave a
Float Plan with a responsible person. Be
sure to cancel the Float Plan when you re-
turn.
● Use common sense and good judgment
when boating. Know your abilities, and be
sure you understand how your boat han-
dles under the different boating conditions
you may encounter. Operate within your
limits, and the limits of your boat. Always
operate at safe speeds, and keep a careful
watch for obstacles and other traffic.
● Always watch carefully for swimmers during
the engine operation.
● Stay away from swimming areas.
● When a swimmer is in the water near you
shift into neutral and shut off the engine.
Be informed about boating safety. Additional
publications and information can be obtained
from many organizations, including the follow-
ing:
United States Coast Guard
Consumer Affairs Staff (G-BC)
Office of Boating, Public, and Consumer Af-
fairs
U.S. Coast Guard Headquarters
Washington, D.C. 20593-0001
Boating Safety Hotline: 1-800-368-5647
National Marine Manufacturers Associa-
tion (NMMA)
401 N. Michigan Ave.
Chicago, Il 60611
Marine Retailers Association of America
155 N. Michigan Ave.
Chicago, Il 60601
EMU25380
Important labels
EMU25395
Warning labels
EMU25401
Label
WARNING
EWM01260
● Be sure shift control is in neutral before
starting engine. (except 2HP)
General information
5
● Do not touch or remove electrical parts
when starting or during operation.
● Keep hands, hair, and clothes away from
flywheel and other rotating parts while
engine is running.
EMU25431
Label
WARNING
EWM01300
● This engine is equipped with a neutral
starting device.
● The engine will not start unless the shift
control is in neutral position.
EMU25464
Caution labels
EMU25472
Label
CAUTION:
ECM01190
Transport and store the engine only as
shown. Otherwise, engine damage could
result from Leaking oil.
EMU25500
Basic boating rules (Rules of
the road)
Just as there are rules which apply when you
are driving on streets and high ways, there
are waterway rules which apply when you are
driving your boat. These rules are used inter-
nationally, and are also enforced by the Unit-
ed States Coast Guard and local agencies.
You should be aware of these rules, and fol-
low them whenever you encounter another
vessel on the water.
Several sets of rules prevail according to geo-
graphic location, but are all basically the same
as the International Rules of the Road. The
rules presented here in your Owner’s Manual
are condensed, and have been provided for
your convenience only. Consult your local
U.S. Coast Guard Auxiliary or Department of
Motor Vehicles for a complete set of rules
governing the waters in which you will be us-
ing your boat.
EMU25510
Steering and sailing rules and sound
signals
Whenever two vessels on the water meet one
another, one vessel has the right-of-way; it is
called the “stand-on” vessel. The vessel
which does not have the right-of-way is called
the “give-way” or “burdened” vessel. These
rules determine which vessel has the right-of-
way, and what each vessel should do.
General information
6
Stand-on vessel
The vessel with the right-of-way has the duty
to continue its course and speed, except to
avoid an immediate collision. When you main-
tain your direction and speed, the other vessel
will be able to determine how best to avoid
you.
Give-way vessel
The vessel which does not have the right-of-
way has the duty to take positive and timely
action to stay out of the way of the Stand-On
vessel. Normally, you should not cross in front
of the vessel with the right-of-way. You should
slow down or change directions briefly and
pass behind the other vessel. You should al-
ways move in such a way that the operator of
the other vessel can see what you are doing.
“The general prudential rule”
This rule is called Rule 2 in the International
Rules and says,
“In obeying and construing these rules due re-
gard shall be had to all dangers of navigation
and collision, and to any special circumstanc-
es, which may render a departure from the
above rules necessary in order to avoid im-
mediate danger.”
In other words, follow the standard rules ex-
cept when a collision will occur unless both
vessels try to avoid each other. If that is the
case, both vessels become “Give-Way” ves-
sels.
EMU25520
Rules when encountering vessels
There are three main situations which you
may encounter with other vessels which could
lead to a collision unless the Steering Rules
are followed:
Meeting: (you are approaching another ves-
sel head-on)
Crossing: (you are traveling across the other
vessel’s path)
Overtaking: (you are passing or being
passed by another vessel)
In the following illustration, your boat is in the
center. You should give the right-of-way to
any vessels shown in white area (you are the
Give-Way vessel). Any vessels in the shaded
area must yield to you (they are the Give-Way
vessels). Both you and the meeting vessel
must alter course to avoid each other.
Meeting
If you are meeting another power vessel head
on, and are close enough to run the risk of col-
lision, neither of you has the right-of-way!
Both of you should alter course to avoid an ac-
cident. You should keep the other vessel on
your port (left) side. This rule doesn’t apply if
both of you will clear one another if you con-
tinue on your set course and speed.
General information
7
Crossing
When two power driven vessels are crossing
each other’s path close enough to run the risk
of collision, the vessel which has the other on
the starboard (right) side must keep out of the
way of the other. If the other vessel is on your
right, you must keep out of its way; you are the
Give-Way vessel. If the other vessel is on
your port (left) side, remember that you
should maintain course and direction, provid-
ed the other vessel gives you the right-of-way
as it should.
Overtaking
If you are passing another vessel, you are the
“Give-Way” vessel. This means that the other
vessel is expected to maintain its course and
speed. You must stay out of its way until you
are clear of it. Likewise, if another vessel is
passing you, you should maintain your speed
and direction so that the other vessel can
steer itself around you.
EMU25530
Other special situations
There are three other rules you should be
aware of when driving your boat around other
vessels.
Narrow channels and bends
When navigating in narrow channels, you
should keep to the right when it is safe and
practical to do so. If the operator of a power-
driven vessel is preparing to go around a
bend that may obstruct the view of other water
vessels, the operator should sound a pro-
longed blast on the whistle (4 to 6 seconds). If
another vessel is around the bend, it too
should sound the whistle. Even if no reply is
heard, however, the vessel should still pro-
ceed around the bend with caution. If you nav-
igate such waters with your boat, you will
need to carry a portable air horn, available
from local marine supply stores.
Fishing vessel right-of-way
All vessels which are fishing with nets, lines or
trawls are considered to be “fishing vessels”
under the International Rules. Vessels with
trolling lines are not considered fishing ves-
sels. Fishing vessels have the right-of-way re-
gardless of position. Fishing vessels cannot,
however, impede the passage of other ves-
sels in narrow channels.
Sailing vessel right-of-way
Sailing vessels should normally be given the
right-of-way. The exceptions to this are:
1. When the sailing vessel is overtaking the
power-driven vessel, the power-driven
vessel has the right-of-way.
2. Sailing vessels should keep clear of any
fishing vessel.
3. In a narrow channel, a sailing vessel
should not hamper the safe passage of a
power-driven vessel which can navigate
only in such a channel.
Reading buoys and other markers
The waters of the United states are marked
for safe navigation by the lateral system of
buoyage. Simply put, buoys and markers
have an arrangement of shapes, colors, num-
bers and lights to show which side of the buoy
a boater should pass on when navigating in a
particular direction. The markings on these
buoys are oriented from the perspective of be-
ing entered from seaward (the boater is going
towards the port). This means that red buoys
are passed on the starboard (right) side when
General information
8
proceeding from open water into port, and
black buoys are to port (left) side. When navi-
gating out of port, your position with respect to
the buoys should be reversed; red buoys
should be to port and black buoys to star-
board.
Many bodies of water used by boaters are en-
tirely within the boundaries of a particular
state. The Uniform State Waterway Marking
System has been devised for these waters.
This system uses buoys and signs with dis-
tinctive shapes and colors to show regulatory
or advisory information. These markers are
white with black letters and orange boarders.
They signify speed zones, restricted areas,
danger areas, and general information.
Remember, markings may vary by geograph-
ic location. Always consult local boating au-
thorities before driving your boat in unfamiliar
waters.
General information
9
EMU25540
Fueling instructions
WARNING
EWM00010
GASOLINE AND ITS VAPORS ARE HIGH-
LY FLAMMABLE AND EXPLOSIVE!
● Do not smoke when refueling, and keep
away from sparks, flames, or other
sources of ignition.
● Stop engine before refueling.
● Refuel in a well-ventilated area. Refuel
portable fuel tanks off the boat.
ZMU01708
General information
10
● Take care not to spill gasoline. If gaso-
line spills, wipe it up immediately with
dry rags.
● Do not overfill the fuel tank.
● Tighten the filler cap securely after refu-
eling.
● If you should swallow some gasoline, in-
hale a lot of gasoline vapor, or get gaso-
line in your eyes, get immediate medical
attention.
● If any gasoline spills onto your skin, im-
mediately wash with soap and water.
Change clothing if gasoline spills on it.
● Touch the fuel nozzle to the filler open-
ing or funnel to help prevent electrostat-
ic sparks.
CAUTION:
ECM00010
Use only new clean gasoline which has
been stored in clean containers and is not
contaminated with water or foreign matter.
EMU25570
Gasoline
If knocking or pinging occurs, use a different
brand of gasoline or premium unleaded fuel.
Gasohol
There are two types of gasohol: gasohol con-
taining ethanol and that containing methanol.
Gasohol containing ethanol can be used if
ethanol content does not exceed 10% and the
fuel meets minimum octane ratings. Yamaha
does not recommended gasohol containing
methanol because it can cause fuel system
damage or engine performance problems.
EMU25680
Engine oil
CAUTION:
ECM01050
All 4-stroke engines are shipped from the
factory without engine oil.
EMU25690
Battery requirement
CAUTION:
ECM01060
Do not use a battery that does not meet the
specified capacity. If a battery which does
not meet specifications is used, the elec-
Recommended gasoline:
Regular unleaded gasoline with a
minimum octane rating of 86 (Pump
Octane Number) = (R+M)/2
Recommended engine oil:
4-stroke motor oil with a combination of
corresponding SAE and API as shown
in the chart
Engine oil quantity (excluding oil filter):
0.8 L (0.85 US qt) (0.70 Imp.qt)
ZMU01710
General information
11
tric system could perform poorly or be
overloaded, causing electric system dam-
age.
For electric start models, choose a battery
which meets the following specifications.
EMU25711
Battery specifications
EMU25730
Without a rectifier or Rectifier
Regulator
CAUTION:
ECM01090
A battery cannot be connected to models
that do not have a rectifier or Rectifier
Regulator.
If you wish to use a battery with the models
without a rectifier or Rectifier Regulator, install
an optional Rectifier Regulator.
Using a maintenance-free battery with the
above models can shorten the life of the bat-
tery significantly.
Install an optional Rectifier Regulator or use
accessories rated to withstand 18 volts or
higher with the above models. Consult your
Yamaha dealer for details on installing an op-
tional Rectifier Regulator.
EMU25741
Propeller selection
The performance of your outboard motor will
be critically affected by your choice of propel-
ler, as an incorrect choice could adversely af-
fect performance and could also seriously
damage the motor. Engine speed depends on
the propeller size and boat load. If engine
speed is too high or too low for good engine
performance, this will have an adverse effect
on the engine.
Yamaha outboard motors are fitted with pro-
pellers chosen to perform well over a range of
applications, but there may be uses where a
propeller with a different pitch would be more
appropriate. For a greater operating load, a
smaller-pitch propeller is more suitable as it
enables the correct engine speed to be main-
tained. Conversely, a larger-pitch propeller is
more suitable for a smaller operating load.
Yamaha dealers stock a range of propellers,
and can advise you and install a propeller on
your outboard that is best suited to your appli-
cation.
Minimum cold cranking amps
(CCA/SAE):
T8PRD 245.0 A
T8PHD 245.0 A
T8EHD 245.0 A
Minimum marine cranking amps
(MCA/ABYC):
T8PRD 323.0 A
T8PHD 323.0 A
T8EHD 323.0 A
Minimum reserve capacity (RC/SAE):
T8PRD 52 minutes
T8PHD 52 minutes
T8EHD 52 minutes
1. Propeller diameter in inches
2. Propeller pitch in inches
3. Type of propeller (propeller mark)
General information
12
NOTE:
Select a propeller which will allow the engine
to reach the middle or upper half of the oper-
ating range at full throttle with the maximum
boat load. If operating conditions such as light
boat loads then allow the engine r/min to rise
above the maximum recommended range, re-
duce the throttle setting to maintain the en-
gine in the proper operating range.
For instructions on propeller removal and in-
stallation, see page 59.
EMU25770
Start-in-gear protection
Yamaha outboard motors or Yamaha-ap-
proved remote control units are equipped with
start-in-gear protection device(s). This feature
permits the engine to be started only when it
is in neutral. Always select neutral before
starting the engine.
1. Propeller diameter in inches
2. Propeller pitch in inches
3. Type of propeller (propeller mark)
Basic components
13
EMU25795
Main components
NOTE:
* May not be exactly as shown; also may not be included as standard equipment on all models.
F6, F8
1. Top cowling
2. Top cowling lock lever
3. Anti-cavitation plate
4. Propeller*
5. Cooling water inlet
6. Drain screw
7. Trim rod
8. Clamp bracket
9. Manual starter handle
10.Warning indicator
11.Engine stop button/Engine stop lanyard
switch
12.Gear shift lever
13.Tiller handle
14.Steering friction lever
15.Tilt lock lever
16.Clamp screw
17.Rope attachment
18.Flushing device
19.Choke knob
Basic components
14
T8
EMU25802
Fuel tank
If your model was equipped with a portable
fuel tank, its function is as follows.
WARNING
EWM00020
The fuel tank supplied with this engine is
its dedicated fuel reservoir and must not
be used as a fuel storage container. Com-
mercial users should conform to relevant
licensing or approval authority regula-
tions.
1. Top cowling
2. Top cowling lock lever
3. Anti-cavitation plate
4. Propeller
5. Cooling water inlet
6. Drain screw
7. Trim rod
8. Clamp bracket
9. Power tilt switch*
10.Manual starter handle*
11.Warning indicator
12.Starter button*
13.Engine stop button/Engine stop lanyard
switch*
14.Gear shift lever*
15.Tiller handle*
16.Steering friction lever*
17.Tilt lock lever*
18.Clamp screw
19.Rope attachment
20.Flushing device
21.Choke knob
22.Remote control box (side mount type)*
Basic components
15
EMU25830
Fuel joint
This joint is used to connect the fuel line.
EMU25841
Fuel gauge
This gauge is located on either the fuel tank
cap or on the fuel joint base. It shows the ap-
proximate amount of fuel remaining in the
tank.
EMU25850
Fuel tank cap
This cap seals the fuel tank. When removed,
the tank can be filled with fuel. To remove the
cap, turn it counterclockwise.
EMU25860
Air vent screw
This screw is on the fuel tank cap. To loosen
the screw, turn it counterclockwise.
EMU26180
Remote control
The remote control lever actuates both the
shifter and the throttle. The electrical switches
are mounted on the remote control box.
EMU26190
Remote control lever
Moving the lever forward from the neutral po-
sition engages forward gear. Pulling the lever
back from neutral engages reverse. The en-
gine will continue to run at idle until the lever
is moved about 35° (a detent can be felt).
Moving the lever farther opens the throttle,
and the engine will begin to accelerate.
1. Air vent screw
2. Fuel gauge
3. Fuel joint
4. Fuel tank cap
ZMU01992
3
2
4
1
1. Power trim and tilt switch
2. Remote control lever
3. Neutral interlock trigger
4. Neutral throttle lever
5. Main switch / choke switch
6. Engine stop lanyard switch
7. Throttle friction adjuster
1. Neutral “”
2. Forward “”
3. Reverse “”
4. Shift
5. Fully closed
6. Throttle
7. Fully open
Basic components
16
EMU26201
Neutral interlock trigger
To shift out of neutral, first pull the neutral in-
terlock trigger up.
EMU26211
Neutral throttle lever
To open the throttle without shifting into either
forward or reverse, put the remote control le-
ver in the neutral position and lift the neutral
throttle lever.
NOTE:
The neutral throttle lever will operate only
when the remote control lever is in neutral.
The remote control lever will operate only
when the neutral throttle lever is in the closed
position.
EMU26221
Choke switch
To activate the choke system, press in the
main switch while the key is turned to the “”
(on) or “” (start) position. The choke sys-
tem will then supply the rich fuel mixture re-
quired to start the engine. When the key is
released, the choke will switch off automati-
cally.
EMU25911
Tiller handle
To change direction, move the tiller handle to
the left or right as necessary.
EMU25921
Gear shift lever
Pulling the gear shift lever towards you puts
the engine in forward gear so that the boat
moves ahead. Pushing the lever away from
you puts the engine in reverse gear so that the
boat moves astern.
1. Neutral interlock trigger
1. Fully open
2. Fully closed
Basic components
17
EMU25941
Throttle grip
The throttle grip is on the tiller handle. Turn
the grip counterclockwise to increase speed
and clockwise to decrease speed.
EMU25961
Throttle indicator
The fuel consumption curve on the throttle in-
dicator shows the relative amount of fuel con-
sumed for each throttle position. Choose the
setting that offers the best performance and
fuel economy for the desired operation.
EMU25970
Throttle friction adjuster
A friction device provides adjustable resis-
tance to movement of the throttle grip or the
remote control lever, and can be set accord-
ing to operator preference.
To increase resistance, turn the adjuster
clockwise. To decrease resistance, turn the
adjuster counterclockwise.
WARNING
EWM00030
Do not overtighten the friction adjuster. If
there is too much resistance, it could be
difficult to move throttle lever or grip,
which could result in an accident.
1. Forward “”
2. Neutral “”
3. Reverse “”
1. Throttle indicator
Basic components
18
When constant speed is desired, tighten the
adjuster to maintain the desired throttle set-
ting.
EMU25990
Engine stop lanyard switch
The lock plate must be attached to the engine
stop switch for the engine to run. The lanyard
should be attached to a secure place on the
operator’s clothing, or arm or leg. Should the
operator fall overboard or leave the helm, the
lanyard will pull out the lock plate, stopping ig-
nition to the engine. This will prevent the boat
from running away under power.
WARNING
EWM00120
● Attach the engine stop switch lanyard to
a secure place on your clothing, or your
arm or leg while operating.
● Do not attach the lanyard to clothing
that could tear loose. Do not route the
lanyard where it could become entan-
gled, preventing it from functioning.
● Avoid accidentally pulling the lanyard
during normal operation. Loss of engine
power means the loss of most steering
control. Also, without engine power, the
boat could slow rapidly. This could
cause people and objects in the boat to
be thrown forward.
NOTE:
The engine cannot be started with the lock
plate removed.
EMU26001
Engine stop button
To open the ignition circuit and stop the en-
gine, push this button.
1. Lanyard
2. Lock plate
1. Lanyard
2. Lock plate
Basic components
19
EMU26011
Choke knob for pull type
To supply the engine with the rich fuel mixture
required to start, pull out this knob.
EMU26070
Manual starter handle
To start the engine, first gently pull the handle
out until resistance is felt. From that position,
then pull the handle straight out quickly to
crank the engine.
EMU26080
Starter button
To start the engine with the electric starter,
push the starter button.
EMU26090
Main switch
The main switch controls the ignition system;
its operation is described below.
● “” (off)
With the main switch in the “” (off) posi-
tion, the electrical circuits are off, and the key
can be removed.
● “” (on)
With the main switch in the “” (on) position,
the electrical circuits are on, and the key can-
not be removed.
● “” (start)
With the main switch in the “” (start) po-
sition, the starter motor turns to start the en-
gine. When the key is released, it returns
automatically to the “” (on) position.
EMU26102
Power tilt switch
The power tilt system adjusts the outboard
motor angle in relation to the transom. Push-
ing the switch “” (up) tilts the outboard mo-
Basic components
20
tor up. Pressing the switch “” (down) tilts
the outboard motor down. When the switch is
released, the outboard motor will stop in its
current position.
NOTE:
For instructions on using the power tilt switch,
see pages 36 and 38.
EMU26110
Steering friction adjuster
A friction device provides adjustable resis-
tance to the steering mechanism, and can be
set according to operator preference. An ad-
juster lever is located on the bottom of the
tiller handle bracket.
To increase resistance, turn the lever to the
left.
To decrease resistance, turn the lever to the
right.
WARNING
EWM00040
Do not overtighten the friction adjuster. If
there is too much resistance, it could be
difficult to steer, which could result in an
accident.
EMU26261
Trim rod (tilt pin)
The position of the trim rod determines the
minimum trim angle of the outboard motor in
relation to the transom.
Basic components
21
EMU26312
Tilt lock mechanism
The tilt lock mechanism is used to prevent the
outboard motor from lifting out of the water
when in reverse gear.
To lock it, set the tilt lock lever in the “”
(lock) position. To release, push the tilt lock le-
ver in the “” (release) position.
EMU26320
Tilt support knob
To keep the outboard motor in the tilted up po-
sition, push the tilt support knob under the
swivel bracket.
EMU26330
Tilt support bar
The tilt support bar keeps the outboard motor
in the tilted up position.
EMU26360
Power tilt unit
This unit tilts the outboard motor up and down
and is controlled with the power tilt switch.
CAUTION:
ECM00630
Do not step on or exert pressure on the
power tilt motor. The power tilt unit could
be damaged as a result.
EMU26382
Top cowling lock lever (pull up type)
To remove the engine top cowling, pull up the
lock lever(s) and lift off the cowling. When in-
stalling the cowling, check to be sure it fits
properly in the rubber seal. Then lock the
cowling by moving the lever(s) downward.
1. Tilt lock lever
1. Power tilt unit
2. Power tilt motor
Loading...