Sony KDL-40 User Manual

TV Colour Digital LCD

Instructions on “Installing the Wall-Mount Bracket” are not supplied in the form of a separate leaflet with this TV. These installation instructions are included within this TV’s instructions manual.

„Instalacja uchwytu ściennego” nie została opisana w oddzielnej ulotce. Ulotka taka nie jest dołączona do tego odbiornika TV. Wskazówki dotyczące instalacji uchwytu ściennego znajdują się w instrukcji obsługi tego odbiornika TV.

Инструкции “Порядок установки настенного монтажного кронштейна” не прилагаются в виде отдельной брошюры к этому телевизору. Эти инструкции по установке содержаться в данной инструкции по эксплуатации телевизора.

For useful information about Sony products

Szczegółowe informacje o produktach Sony

Для получения полезной информации о продукции Сони

KDL-52Z4500

KDL-46Z4500

KDL-40Z4500

4-116-578-51(1)

LCD Digital Colour TV

	Operating Instructions				GB
	Instrukcja obsługi				PL
	Инструкция по эксплуатации				RU

Printed in Spain	© 2008 Sony Corporation	4-116-578-51(1)

Introduction

Thank you for choosing this Sony product.

Before operating the TV, please read this manual thoroughly and retain it for future reference.

The manufacturer of this product is Sony Corporation, 1-7-1 Konan Minato-ku Tokyo, 108-0075 Japan. The Authorized Representative for EMC and product safety is Sony Deutschland GmbH, Hedelfinger Strasse 61, 70327 Stuttgart, Germany. For any service or guarantee matters please refer to the addresses given in separate service or guarantee documents.

Notice for Digital TV function

sAny functions related to Digital TV ( ) will only work in countries or areas where DVB-T (MPEG2 and MPEG4 AVC) digital terrestrial signals are broadcast or where you have access to a compatible DVB-C (MPEG2 and MPEG4 AVC) cable service. Please confirm with your local dealer if you can receive a DVB-T signal where you live or ask your cable provider if their DVB-C cable service is suitable for integrated operation with this TV.

sThe cable provider may charge an additional fee for such a service and you may be required to agree to their terms and conditions of business.

sAlthough this TV set follows DVB-T and DVB-C specifications, compatibility with future DVB-T digital terrestrial and DVB-C digital cable broadcasts cannot be guaranteed.

sSome Digital TV functions may not be available in some countries/regions and DVB-C cable may not operate correctly with all providers.

sFor more information about DVB-C functionality please see our cable support site: http://support.sony-europe.com/TV/DVBC/

Trademark information

s is a registered trademark of the DVB Project

sDLNA and DLNA CERTIFIED are trademarks and/or service marks of Digital Living Network Alliance.

sGUIDE Plus+ is (1) a registered trademark or trademark of, (2) manufactured under license from and (3) subject of various international patents and patent applications owned by, or licensed to, Gemstar-TV Guide International, Inc. and/or its related affiliates.

sGEMSTAR-TV GUIDE INTERNATIONAL, INC. AND/OR ITS RELATED AFFILIATES ARE NOT IN ANY WAY LIABLE FOR THE ACCURACY OF THE PROGRAM SCHEDULE INFORMATION PROVIDED BY THE GUIDE PLUS+ SYSTEM. IN NO EVENT SHALL GEMSTAR-TV GUIDE INTERNATIONAL, INC. AND /OR ITS RELATED AFFILIATES BE LIABLE FOR ANY AMOUNTS REPRESENTING LOSS OF PROFITS, LOSS OF BUSINESS, OR INDIRECT, SPECIAL, OR CONSEQUENTIAL DAMAGES IN CONNECTION WITH THE PROVISION OR USE OF ANY INFORMATION, EQUIPMENT, OR SERVICES RELATING TO THE GUIDE PLUS+ SYSTEM.

sManufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories.

sHDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.

s“BRAVIA” and are trademarks of Sony Corporation.

s“XMB” and “xross media bar” are the trademarks of Sony Corporation and Sony Computer Entertainment Inc.

2 GB

Table of Contents

Start-up Guide	4
Safety information............................................................................................................................	9
Precautions.....................................................................................................................................	11
Remote and TV Controls/Indicators .............................................................................................	12
Watching TV
Watching TV....................................................................................................................................	16
Using GUIDE Plus+™ System and the Digital Electronic Programme Guide (EPG)	..... 18
Using the Digital Favourite List ..........................................................................................	22
Using Optional Equipment
Connecting Chart ...........................................................................................................................	23
Viewing Pictures from Connected Equipment.............................................................................	26
Playing Back Photo/Music via USB ..............................................................................................	27
Using BRAVIA Sync with Control for HDMI .................................................................................	30
Operating Optional Equipment using the TV Remote.................................................................	31
Using Network Features
Connecting the TV to the Network................................................................................................	34
Enjoying Photo/Music Files via the Network ...............................................................................	34
Checking the Network Connection...............................................................................................	36
Adjusting the Server Display Settings .........................................................................................	36
Using MENU Functions
Navigating through TV Home Menu (XMB™)...............................................................................	38
Settings ...........................................................................................................................................	39
	GB
Additional Information
Installing the Accessories (Wall-Mount Bracket) ........................................................................	52
Specifications .................................................................................................................................	54
Troubleshooting .............................................................................................................................	56
: for digital channels only

Before operating the TV, please read the “Safety information” section of this manual.

Retain this manual for future reference.

3 GB

Start-up Guide

Before Use

To check the accessories

Mains lead (1)

Remote RM-ED012 (1)

Size AA batteries (R6 type) (2)

Stand (1) and screws for stand (4) (KDL-46Z4500/KDL-40Z4500 only)

To insert batteries into the remote

Push and lift the cover to open.

~

•Observe the correct polarity when inserting batteries.

•Do not use different types of batteries together or mix old and new batteries.

•Dispose of batteries in an environmentally friendly way. Certain regions may regulate the disposal of batteries. Please consult your local authority.

•Handle the remote with care. Do not drop or step on it, or spill liquid of any kind onto it.

•Do not place the remote in a location near a heat source, a place subject to direct sunlight, or a damp room.

To replace the speaker grille

The speaker grille unit can be replaced with others that are sold separately. However, do not remove the unit except to replace it. For details, see the instructions supplied with speaker grille units.

1: Attaching the stand (for KDL-46Z4500/ KDL-40Z4500)

1Open the carton box and take out the stand and the screws.

2Place the TV set on the stand. Take care not to interfere with cables.

3Fix the TV to the stand according to the arrow marks that guide the screw holes using the supplied screws.

~

•If using an electric screwdriver, set the tightening torque at approximately 1.5 N·m {15 kgf·cm}.

4 GB

2: Connecting an aerial/Set Top Box/recorder (e.g. DVD recorder)

Connecting a Set Top Box/recorder (e.g. DVD recorder) with SCART

AV 2

( SMARTLINK )

3: Preventing the TV from toppling over

Guide up-Start

Scart lead

Set Top Box/recorder (e.g. DVD recorder)

Connecting a Set Top Box/recorder (e.g. DVD recorder) with HDMI

HDMI cable

Set Top Box/recorder (e.g. DVD recorder)

1Install a wood screw (4 mm in diameter, not supplied) in the TV stand.

2Install a machine screw (M6 x 12-15, not supplied) into the screw hole of the TV.

3Tie the wood screw and the machine screw with a strong cord.

4: Bundling the cables

2

3

4

1

~

•Do not bundle the mains lead together with other cables.

5 GB

5: Performing the initial setup

2

1

3-11

1Connect the TV to your mains socket (220-240V AC, 50Hz).

2Press 1 on the TV.

When you switch on the TV for the first time, the Language menu appears on the screen.

3Press F/f/G/g to select the language displayed on the menu screens, then press .

Language

English	Česky
Nederlands	Magyar
Français	Русский
Italiano	ББлгарски
Deutsch	Suomi
	Dansk
Türkçe	Svenska
Español	Norsk
Català	Slovenčina
Português	Română
Polski

4Press F/f to select the country in which you will operate the TV, then press .

Country

Select country.

-

United Kingdom

Ireland

Nederland

België/Belgique

Luxembourg

France

Italia

If the country in which you want to use the TV does not appear in the list, select “-” instead of a country.

5Press F/f to select the location type in which you will operate the TV, then press .

~

•Select “Home” for the best TV settings to use the TV in the home.

Location

Select location.

Home

Shop

6 Select “Yes” then press .

Auto Tuning

Do you want to start Auto Tuning?

Yes

No

7Press F/f to select “Antenna” or “Cable”, then press .

If you select “Cable”, the screen for selecting the scan type appears. See “To tune the TV for Cable connection” (page 7).

The TV starts searching for all available digital channels, followed by all available analogue channels. This may take some time, so do not press any buttons on the TV or remote while proceeding.

6 GB

If a message appears for you to confirm the aerial connection

No digital or analogue channels were found. Check all the aerial/cable connection and then press to start autotuning again.

8When the Programme Sorting menu appears on the screen, follow the steps of “Programme Sorting” (page 46).

If you do not change the order in which the analogue channels are stored on the TV, press RETURN to go to step 9.

9

Quick Start

Do you want to enable Quick Start?

TV turns on more quickly but standby power consumption is increased.

Yes

No

For details, see page 41.

10

Control for HDMI

Do you want to enable control for compatible

HDMI devices?

Choosing "Yes" will increase standby power consumption.

Yes

No

For details, see page 30.

Following this step, GUIDE Plus+ setting screen appears only when GUIDE Plus+ is available.

11Press .

The TV has now tuned in all the available channels.

~

•When a digital broadcast channel cannot be received, or when selecting a country in which there are no digital broadcasts in step 4, the time must be set after performing step 8.

To tune the TV for Cable connection

1Press .

2Press F/f to select “Quick Scan” or “Full Scan”, then press .

“Quick Scan” : channels are tuned according to the cable operator information within the broadcast signal. Recommended setting for “Frequency”, “Network ID” and “Symbol Rate” is “Auto.”

This option is recommended for fast tuning when supported by your cable operator.

If the “Quick Scan” does not tune, please use the “Full Scan” method below. “Full Scan” : All available channels are

tuned and stored. This procedure may take some time.

This option is recommended when “Quick Scan” is not supported by your cable provider.

For further information about supported cable providers, refer to support web site: http://support.sony-europe.com/TV/ DVBC/

3Press f to select “Start”, then press .

The TV starts searching for channels. Do not press any buttons on the TV or remote.

~

•Some cable providers do not support “Quick Scan.” If no channels are detected using “Quick Scan”, perform “Full Scan.”

To setup GUIDE Plus+ system (only when GUIDE Plus+ system is available)*

*Condition you can setup this feature:

–in UK, Italy, Germany or Spain.

–you can receive digital broadcasting.

–when “Antenna” is selected in step 7 of “ 5: Performing the initial set-up.”

1Enter Postal Code of region you live using F/f/G/g/+.

~

•Enter from the left, when the postal code is fewer than seven digits.

Guide up-Start

(Continued) 7 GB

2Select language for GUIDE Plus+.

This step will be skipped if any one of the following languages is selected in “5: Performing the initial set-up” step 3: “English”, “Deutsch”, “Español”, “Italiano”, “Français” or “Nederlands.”

3GUIDE Plus+ Data Download.

The initial download may take some time, so do not press any buttons on the TV or remote while proceeding. Once you have received the first download of TV listings data, all future downloads will be done automatically.

Adjusting the Viewing

Angle of the TV

This TV can be adjusted within the angles shown below.

Adjust the angle left and right (swivel)

	Top view
20°	20°
20°	20°
	Front

~

•When adjusting the angle, hold the Table-Top Stand with one hand to avoid slipping or tipping the TV.

Detaching the Table-Top Stand from the TV

~

•Remove the screws guided by the arrow marks of the TV.

•Do not remove the Table-Top Stand for any reason other than listed below.

–To wall-mount the TV.

–To put the TV in the carton at time of purchase (KDL-46Z4500/KDL-40Z4500 only).

8 GB

Safety information

Installation/Set-up

Install and use the TV set in accordance with the instructions below in order to avoid any risk of fire, electrical shock or damage and/or injuries.

Installation

sThe TV set should be installed near an easily accessible mains socket.

sPlace the TV set on a stable, level surface.

sOnly qualified service personnel should carry out wall installations.

sFor safety reasons, it is strongly recommended that you use Sony accessories, including:

– Wall-mount bracket SU-WL500

sBe sure to use the screws supplied with the Wall-mount bracket when attaching the mounting hooks to the TV set.

The supplied screws are designed so that they are 8 mm to 12 mm in length when measured from the attaching surface of the mounting hook.

The diameter and length of the screws differ depending on the Wall-mount bracket model.

Use of screws other than those supplied may result in internal damage to the TV set or cause it to fall, etc.

8mm – 12mm

Screw (supplied with the Wall-

mount bracket)

Mounting Hook

Hook attachment on rear of TV set

Transporting

sBefore transporting the TV set, disconnect all cables.

sTwo or three people are needed to transport a large TV set.

sWhen transporting the TV set by hand, hold it as shown on the right. Do not put stress on the LCD panel and the frame around the screen.

sWhen lifting or moving the TV set, hold it firmly from the bottom.

sWhen transporting the TV set, do not subject it to jolts or excessive vibration.

sWhen transporting the TV set for repairs or when moving, pack it using the original carton and packing material.

Be sure to hold the bottom of the panel, and not the transparent part, speaker, or speaker grille area. Do not compress the panel’s speaker grille area.

Ventilation

sNever cover the ventilation holes or insert anything in the cabinet.

sLeave space around the TV set as shown below.

sIt is strongly recommended that you use a Sony wall-mount bracket in order to provide adequate air-circulation.

Installed on the wall

30 cm

10 cm							10 cm

10 cm

Leave at least this space around the set.

Installed with stand

30 cm

10 cm

10 cm

6 cm

Leave at least this space around the set.

sTo ensure proper ventilation and prevent the collection of dirt or dust:

–Do not lay the TV set flat, install upside down, backwards, or sideways.

–Do not place the TV set on a shelf, rug, bed or in a closet.

–Do not cover the TV set with a cloth, such as curtains, or items such as newspapers, etc.

–Do not install the TV set as shown below.

Air circulation is	Air circulation is
blocked.	blocked.

Wall

Wall

(Continued) 9 GB

Mains lead

Handle the mains lead and socket as follows in order to avoid any risk of fire, electrical shock or damage and/or injuries:

–Use only mains leads supplied by Sony, not other suppliers.

–Insert the plug fully into the mains socket.

–Operate the TV set on a 220-240 V AC supply only.

–When wiring cables, be sure to unplug the mains lead for your safety and take care not to catch your feet on the cables.

–Disconnect the mains lead from the mains socket before working on or moving the TV set.

–Keep the mains lead away from heat sources.

–Unplug the mains plug and clean it regularly. If the plug is covered with dust and it picks up moisture, its insulation may deteriorate, which could result in a fire.

Notes

sDo not use the supplied mains lead on any other equipment.

sDo not pinch, bend, or twist the mains lead excessively. The core conductors may be exposed or broken.

sDo not modify the mains lead.

sDo not put anything heavy on the mains lead.

sDo not pull on the mains lead itself when disconnecting the mains lead.

sDo not connect too many appliances to the same mains socket.

sDo not use a poor fitting mains socket.

Prohibited Usage

Do not install/use the TV set in locations, environments or situations such as those listed below, or the TV set may malfunction and cause a fire, electrical shock, damage and/or injuries.

Location:

Outdoors (in direct sunlight), at the seashore, on a ship or other vessel, inside a vehicle, in medical institutions, unstable locations, near water, rain, moisture or smoke.

Environment:

Places that are hot, humid, or excessively dusty; where insects may enter; where it might be exposed to mechanical vibration, near flammable objects (candles, etc).

The TV set shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the TV.

Situation:

Do not use when your hands are wet, with the cabinet removed, or with attachments not recommended by the manufacturer. Disconnect the TV set from mains socket and aerial during lightning storms.

Broken pieces:

sDo not throw anything at the TV set. The screen glass may break by the impact and cause serious injury.

sIf the surface of the TV set cracks, do not touch it until you have unplugged the mains lead. Otherwise electric shock may result.

When not in use

sIf you will not be using the TV set for several days, the TV set should be disconnected from the mains for environmental and safety reasons.

sAs the TV set is not disconnected from the mains when the TV set is just turned off, pull the plug from the mains to disconnect the TV set completely.

sHowever, some TV sets may have features that require the TV set to be left in standby to work correctly.

For children

sDo not allow children to climb on the TV set.

sKeep small accessories out of the reach of children, so that they are not mistakenly swallowed.

If the following problems occur...

Turn off the TV set and unplug the mains lead immediately if any of the following problems occur.

Ask your dealer or Sony service centre to have it checked by qualified service personnel.

When:

–Mains lead is damaged.

–Poor fitting of mains socket.

–TV set is damaged by being dropped, hit or having something thrown at it.

–Any liquid or solid object falls through openings in the cabinet.

10 GB

Precautions

Viewing the TV

sView the TV in moderate light, as viewing the TV in poor light or during long period of time, strains your eyes.

sWhen using headphones, adjust the volume so as to avoid excessive levels, as hearing damage may result.

LCD Screen

sAlthough the LCD screen is made with high-precision technology and 99.99% or more of the pixels are effective, black dots may appear or bright points of light (red, blue, or green) may appear constantly on the LCD screen. This is a structural property of the LCD screen and is not a malfunction.

sDo not push or scratch the front filter, or place objects on top of this TV set. The image may be uneven or the LCD screen may be damaged.

sIf this TV set is used in a cold place, a smear may occur in the picture or the picture may become dark. This does not indicate a failure. These phenomena disappear as the temperature rises.

sGhosting may occur when still pictures are displayed continuously. It may disappear after a few moments.

sThe screen and cabinet get warm when this TV set is in use. This is not a malfunction.

sThe LCD screen contains a small amount of liquid crystal. Some fluorescent tubes used in this TV set also contain mercury. Follow your local ordinances and regulations for disposal.

Handling and cleaning the screen surface/ cabinet of the TV set

Be sure to unplug the mains lead connected to the TV set from mains socket before cleaning.

To avoid material degradation or screen coating degradation, observe the following precautions.

sTo remove dust from the screen surface/cabinet, wipe gently with a soft cloth. If dust is persistent, wipe with a soft cloth slightly moistened with a diluted mild detergent solution.

sNever use any type of abrasive pad, alkaline/acid cleaner, scouring powder, or volatile solvent, such as alcohol, benzene, thinner or insecticide. Using such materials or maintaining prolonged contact with rubber or vinyl materials may result in damage to the screen surface and cabinet material.

sPeriodic vacuuming of the ventilation openings is recommended to ensure to proper ventilation.

sWhen adjusting the angle of the TV set, move it slowly so as to prevent the TV set from moving or slipping off from its table stand.

Optional Equipment

Keep optional components or any equipment emitting electromagnetic radiation away from the TV set. Otherwise picture distortion and/or noisy sound may occur.

Disposal of the TV set

Disposal of Old Electrical & Electronic Equipment (Applicable in the European

Union and other European countries with separate

collection systems)

This symbol on the product or on its packaging indicates that this product shall not be treated as household waste. Instead it shall be handed over to the applicable

collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. The recycling of materials will help to conserve natural resources. For more detailed information about recycling of this product, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

Disposal of waste batteries (applicable in the European Union and other European countries with separate collection systems)

This symbol on the battery or on the packaging indicates that the battery provided with this product shall not be treated as household waste. By ensuring these batteries are disposed

of correctly, you will help prevent potentially negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of the battery. The recycling of the materials will help to conserve natural resources. In case of products that for safety, performance or data integrity reasons require a permanent connection with an incorporated battery, this battery should be replaced by qualified service staff only. To ensure that the battery will be treated properly, hand over the product at end-of-life to the applicable collection point for the recycling of electrical and electronic equipment. For all other batteries, please view the section on how to remove the battery from the product safely. Hand the battery over to the applicable collection point for the recycling of waste batteries. For more detailed information about recycling of this product or battery, please contact your local Civic Office, your household waste disposal service or the shop where you purchased the product.

11 GB

Remote and TV Controls/Indicators

Remote and TV controls

2

0 87 8,qj 8,qf

A button or touch sensors on the TV will work the same as those on the remote.

* In the TV menu, these touch sensors will work as F/f/G/g/. z

• The number 5, N, PROG + and AUDIO buttons on the remote have a tactile dot. Use the tactile dots as a reference when operating the TV.

Button	Description

1 TV "/1 (TV Press to turn the TV on and off from standby mode. standby)

2 1 (Power) Press to turn the TV on or off.

~

• To disconnect the TV completely, turn off the TV, then unplug the mains lead from the mains.

3 (Screen Press to change the screen format (page 17). mode)

4	AUDIO	In analogue mode: Press to change the dual sound
		mode (page 41).
		In digital mode: Press to change the language to be
		used for the programme currently being viewed
		(page 49).
5	(Subtitle	Press to change the subtitle language (page 48) (in
	setting)	digital mode only).

12 GB

Button	Description

6/ (Info/ In digital mode: Displays details of the programme Text reveal) currently being viewed.

In analogue mode: Displays information. Press once

		to display the current channel number and screen
		mode. Press again to display clock information. Press
		a third time to remove the display from the screen.
		In Text mode (page 17): Reveals hidden
		information (e.g. answers to a quiz).
7	/ (Input	In TV mode: Press to display a list of inputs
	select/Text	(page 26).
	hold)	In Text mode: Press to hold the current page.
8 F/f/G/g/		Press F/f/G/g to move the on-screen cursor. Press
		to select/confirm the highlighted item.
		When playing a photo file: Press	to pause/start a
		slideshow. Press F/G to select the previous file.
		Press f/g to select the next file.
		When playing a music file: Press	to pause/start
		the playback. Press and hold G/g to fast forward/
		fast reverse, then release the button at the point
		where you want to resume playback. Press F to
		start playback from the beginning of the current
		file. Press f to go to the next file.
9 OPTIONS		Press to display a list that contains “PAP”
		(page 26), “PIP” (page 27), “Device Control”, or
		shortcuts to some setting menus. Use the “Device
		Control” menu to operate equipment that is
		compatible with control for HDMI.
		The listed options vary depending on the input
		source.
0 HOME		Press to display the TV Home menu (page 38).
qa Coloured		When the coloured buttons are available, an
	buttons	operation guide appears on the screen. Follow the
		operation guide to perform a selected operation.
qs Number		In TV mode: Press to select channels. For channel
	buttons	numbers 10 and above, press the second and third
		digits in quick succession.
		In Text mode: Press to enter a page number.
qd	(Favourite)	Press to display the digital favourite list that you
		have specified (page 22).
qf PROG +/–/		In TV mode: Press to select the next (+) or
	/	previous (–) channel.
		In Text mode: Press to select the next ( ) or
		previous ( ) page.

qg (Previous Press to return to the channel that was last viewed channel) (for more than five seconds).

(Continued) 13 GB

Button

Description

qh % (Mute)

Press to mute the sound. Press again to restore the

sound.

z

• In standby mode, if you want to turn on the TV

without sound, press this button.

qj 2 +/–

Press to adjust the volume.

(Volume)

qk / (Text)

Press to display text information (page 17).

ql RETURN /

Press to return to the previous screen of the

displayed menu.

When playing a photo/music file: Press to stop the

playback. (The display returns to the file or folder

list.)

w; GUIDE /

Press to display the Digital Electronic Programme

(EPG)

Guide (EPG) (page 18, 21).

wa ANALOG

Press to display the analogue channel that was last

viewed.

ws DIGITAL

Press to display the digital channel that was last

viewed.

wd THEATRE

You can set Theatre Mode to on or off. When

Theatre Mode is set to on, the optimum audio

output (if the TV is connected with an audio

system using an HDMI cable) and picture quality

for film-based contents are automatically set.

z

• If you turn the TV off, Theatre Mode is also

turned off.

• “Control for HDMI” (BRAVIA Sync) is only

available with the connected Sony equipment that

has the BRAVIA Sync or BRAVIA Theatre Sync

logo or is compatible with control for HDMI.

wf SYNC MENU Displays the menu of connected HDMI equipment. While viewing other input screens or TV programmes, “HDMI Device Selection” is displayed when the button is pressed.

z

•“Control for HDMI” (BRAVIA Sync) is only available with the connected Sony equipment that has the BRAVIA Sync logo or is compatible with control for HDMI.

wg (Light) Press to illuminate the buttons on the remote so that you can see them easily even if the room is dark.

wh Buttons for You can operate the equipment connected to the using TV (page 24, 30, 31).

optional equipment

14 GB

Indicators

1

2

3

4 5

Indicator	Description

1 (Picture Off/Timer Lights up in green when the picture is switched off (page 41). indicator) Lights up in orange when the reminder is set (page 19, 21) or the timer is

set (page 43).

2 1 (Standby indicator) Lights up in red when the TV is in standby mode.

3 " (Power indicator)	Lights up in green when the TV is turned on.
4 Light Sensor	Do not put anything over the sensor, as its function may be affected.
5 Remote control sensor	Receives IR signals from the remote.
	Do not put anything over the sensor, as its function may be affected.

~

•Make sure that the TV is completely turned off before unplugging the mains lead. Unplugging the mains lead while the TV is turned on may cause the indicator to remain lit or may cause the TV to malfunction.

•Do not put anything over the indicators as their functions may be affected.

15 GB

Watching TV

Watching TV

1

2

3

3

1Press 1 on the TV to switch on the TV.

When the TV is in standby mode (the 1 (standby) indicator on the TV (front) is red), press TV "/1 on the remote to switch on the TV.

2Press DIGITAL to switch to digital mode or ANALOG to switch to analogue mode.

The channels available vary depending on the mode.

3Press the number buttons or PROG +/– to select a TV channel.

To select channel numbers 10 and above using the number buttons, enter the second and third digits within two seconds.

To select a digital channel using the Guide, see page 18 or 21.

In digital mode

An information banner appears briefly. The following icons may be indicated on

the banner.

: Radio service

: Scrambled/Subscription service

: Multiple audio languages available

: Subtitles available

: Subtitles available for the hearing impaired

:Recommended minimum age for current programme (from 4 to 18 years)

: Parental Lock

Additional operations

To	Do this
Turn on the TV from	Press %. Press 2 +/– to
Standby mode	set the volume level.
without sound
Adjust the volume	Press 2 + (increase)/
	– (decrease).

16 GB

To access Text

Press /. Each time you press /, the display changes cyclically as follows:

Text t Text over the TV picture (mix mode) t No Text (exit the Text service)

To select a page, press the number buttons or

PROG +/–.

To hold a page, press / .

To reveal hidden information, press /. z

•When four coloured items appear at the bottom of the Text page, Fastext is available. Fastext allows you to access pages quickly and easily. Press the corresponding coloured button to access the page.

To change the screen format manually

Press repeatedly to select the desired screen format.

Smart*

Displays conventional 4:3 broadcasts with an imitation wide screen effect. The 4:3 picture is stretched to fill the screen.

4:3

Displays conventional 4:3 broadcasts (e.g. non-wide screen TV) in the correct proportions.

Wide

Displays wide screen (16:9) broadcasts in the correct proportions.

Zoom*

Displays cinemascopic (letter box format) broadcasts in the correct proportions.

14:9*

Displays 14:9 broadcasts in the correct proportions. As a result, black border areas are visible on the screen.

* Parts of the top and bottom of the picture may be cut off.

~

•Some characters and/or letters at the top and the bottom of the picture may not be visible in Smart mode. In such a case, you can select “Vertical Size” using the “Screen Settings” (page 43) menu and adjust vertical size to make it visible.

z

•When “Auto Format” is set to “On”, the TV will automatically select the best mode to suit input signal.

•You can adjust the position of the picture when selecting “Smart”, “14:9” or “Zoom.” Press F/f to move up or down (e.g. to read subtitles).

Using the Options menu

Press OPTIONS to display the following options when viewing a TV programme.

Options	Description
Picture Mode	See page 39.
Sound Mode	See page 40.
Surround	See page 40.
Speaker	See page 45.
Motionflow	See page 42.
Subtitle Setting (in	See page 48.
digital mode only)
Sleep Timer	See page 43.
Power Saving	See page 41.
System Information	See page 50.
(in digital mode only)

TV Watching

17 GB

Using GUIDE Plus+™ System* and the Digital Electronic Programme Guide (EPG) **

*Condition you can set-up this feature:

–in UK, Italy, France, Germany or Spain.

–you can receive digital broadcasting.

–when “Antenna” is selected in step 7 of “ 5: Performing the initial set-up.”

**This function may not be available in some countries/regions.

Using GUIDE Plus+

Use GUIDE Plus+ system to find the show that you want to watch. The feature allows you to search for shows by programme categories and by keyword. The GUIDE Plus+ programme provides up to eight days of TV programming information. Be sure to complete the initial set-up on page 6 to use this service.

GUIDE Plus+ System Components

GUIDE Plus+ logo

Branding partner logo

Sky	29-May 07:15

Video window

Information panels

Remind

Go to Ad

Top

Action bar

Arthur : Animation following the adventures of a young aardvark and his friends.

Buster discovers the joy of growing your own vegetables.

Information

BBC2 8:00-8:30

box

Menu bar

Grid

Search

MyTV

Schedule

Set-up

Thu, 29 7:00

7:30

8:00

8:30

Breakfast

Breakfast

In the Night Garden

Cbeebies Springwatch

Arthur

GMTV Today

Channel

Freshly Squeezed

Everybody loves Ray...

Just Shoot Me

logo and

The Adve...

Rupert B...

Roary th...

Make Wa...

Fifi and t...

Tomas ...

programme

Spendaholics

Greek

title

Emmerd...

The Montel Williams Show

Sally Jessy Raphael

Anything Goes

z

•Image shown above varies depending on country/region.

•Information panels is not Sony provided, adverts from Branding Partner.

•The function of action bar varies with cursor location and when in settings.

1Press GUIDE.

2Perform the desired operation as shown in the following table or displayed on the screen.

To	Do this
View a programme	Press F/f/G/g to select a programme, then press .
	~
	• The programme information will appear in the information box.
	• Press / to access the extended information box for a long
	synopsis.
	• You can use PROG+/– to page up/down through the listings.
	Press BRAVIA sync m/M to go to the next day or one day back.
Turn off the TV Guide	Press GUIDE to exit TV Guide.

18 GB

To	Do this

Set a programme to be displayed automatically on the screen when it starts

– Reminder

Press F/f/G/g to select a future programme you want to watch, then press the green button.

~

•To cancel a reminder, press red button when the reminder is highlighted or use “Schedule” on the menu bar.

•If you switch the TV to standby mode, it will automatically turn itself on when the programme is about to start.

Menu bar	Press F repeatedly to access the menu bar.
	Press G/g to select area. (“Grid”, “Search”, “My TV”, “Schedule”
	and “Set-up”)
	You can view a programme or set a reminder in “Grid” area.
Search a programme	You can quickly and easily find something of interest to watch or to
– Search	set a reminder by category (e.g. Sport) or subcategory (e.g. Football)
	of a programme.
	1	Highlight “Search” on the menu bar, then, press f only one
	2	time.
		Press F/f/G/g to select a category or subcategory, then press
		.
Search your own keyword	In addition to the standard categories and sub-categories, you can set
– My Choice	your own search keywords.
	1	Highlight “My Choice” in the “Search” area on the menu bar.
	2	Press yellow button to add a keyword, then the virtual keyboard
	3	appears.
		Use the virtual keyboard to enter your keyword.
	4	Confirm with the green button.
	5	Your personal keyword appears in the “My Choice.”
	6	Select your keyword and press to start a search according to
		your personal keyword.
Set a Profile and receive	The “My TV” area allows you to set up a personal profile.
recommendations according to your	You can define a personal profile by channels, categories and/or by
preferences	keywords.
– My TV	The “My TV” area is making recommendations to you to quickly and
	easily find something of interest to watch or to set a reminder.
	How to set your profile:
	1	Highlight “My TV” on the menu bar, press the green button to
	2	set your profile.
		Press F/f to select channels, categories or keywords.
	3	Press the yellow button to add a channel, a category or a
	4	keyword to your profile.
		Press F/f/G/g to select a channel, a category or a keyword, then
	5	press .
		Repeat step 2 to 4 to add more items.
	6	Press	to activate your profile.
	z
	• You can delete or edit with the red and green buttons.
Delete and edit reminder	1	Highlight “Schedule” on the menu bar.
– Schedule	2	Press F/f to delete or edit with the red and green buttons.

z

•When no reminder is set, “No programmes” is displayed. Press g to highlight “Frequency” (e.g.weekly) or “Timing” (e.g.reminder timing:10 min early), you can change this settings by pressing colour buttons.

TV Watching

(Continued) 19 GB

To	Do this

Configure the GUIDE Plus+ system according to your personal situation

– Set-up

1Highlight “Set-up” on menu bar.

2Press F/f for you to select below items you want to configure.

“Personal Preferences”: You can change the on screen language, change reminder timing and set overnight download.

“Start Installation Sequence”: This feature provides an easy way to restart your installation from scratch. This will delete all your current TV listing data.

“Manual Data Download”: Update your TV listings immediately. If the TV is switched off during several days, TV listings will not be updated automatically. In this case, use this feature to update TV listings.

“GUIDE Plus+ System Information” screen: Display GUIDE Plus+ system information. This screen is providing several values that are helpful for troubleshooting.

20 GB

Using the Digital Electronic Programme Guide (EPG) **

		All Categories							Fri 16 Mar 11:35
	Today		11: 30		12: 00		12: 30	13: 00
	001	BBC ONE	Homes Under the Hammer				Neighbours		Afterlife
	002	BBC TWO	Ready Steady Cook		...Extraordinary People: Britains Iden			...CSI: Crime Scene Inv
	003	ITV1	Dancing On Ice Exclusive						Cracker
	004	Channel 4	...Sign Zone: Ancient Rome: The Rise a				...The Jeremy Kyle		...Homes Under th
	005	Five	House			...Law and Order: Special Victims U		...PartyPoker.com Worl
	006	ITV2	Crime Hour: Midsomer Murders						...Vodafone TBA: L
	007	BBC THREE	BBC Learning Zone: Schools: World P...				A Picture of Brit...		Eastenders
	008	BBC FOUR	ER		...Real Crime: The Truth About the			This is BBC FOUR
	009	ITV3	Past	Everybody Loves Raymond					...The Sharon Osb
	010	SKY THREE	Racing from Chepstow and Ascot				Baseball Wedne...		Trans World Sport
			Previous			Next	30 min View		Category

1In digital mode, press GUIDE.

2Perform the desired operation as shown in the following table or displayed on the screen.

**This function may not be available in some countries/regions.

To switch the GUIDE (Sony Guide or GUIDE Plus+), see page 50.

To	Do this
Watch a programme	Press F/f/G/g to select the programme, then press .
Turn off the Guide	Press		GUIDE.
Sort the programme information by	1	Press the blue button.
category	2	Press F/f to select a category, then press .
– Category list
Set a programme to be displayed	1	Press F/f/G/g to select the future programme you want to
automatically on the screen when it		display, then press / .
starts	2	Press F/f to select “Reminder”, then press .
– Reminder		A c symbol appears by that programme’s information. The

indicator on the TV front panel lights up in orange.

~

•If you switch the TV to standby mode, it will automatically turn itself on when the programme is about to start.

Cancel reminder	1	Press / .
– Cancel Timer	2	Press F/f to select “Timer list”, then press .
	3	Press F/f to select the programme you want to cancel, then
	4	press .
		Press F/f to select “Cancel Timer”, then press .
		A display appears to confirm that you want to cancel the
	5	programme.
		Press G/g to select “Yes”, then press to confirm.

TV Watching

21 GB

Using the Digital Favourite List *

1 In digital mode, press .

2 Perform the desired operation as shown in the following table or displayed on the screen.

Homes Under the Hammer

10:30 - 11:00

Digital favourite list

* This function may not be available in some countries/regions.

To

Do this

Create your favourite list for the first time

1

2

3

Press to select “Yes.”

Press the yellow button to select the favourite list.

Press F/f to select the channel you want to add, then press . A symbol appears next to channels that you have stored in the favourite list.

Watch a channel

1

2

Press yellow key to navigate through favourite lists. Press F/f to select the channel, then press .

Turn off the favourite list	Press		RETURN.
Add or remove channels in the	1	Press the blue button.
currently edited favourite list	2	Press the yellow button to choose the list you want to edit.
	3	Press F/f/G/g to select the channel you want to add or remove,
		then press .

Remove all channels from the current favourite list

1

2

3

4

Press the blue button.

Press the yellow button to select the favourite list you want to edit.

Press the blue button.

Press G/g to select “Yes”, then press to confirm.

22 GB

Using Optional Equipment

Connecting Chart

You can connect a wide range of optional equipment to your TV. Connecting cables are not supplied.

1 2 3 4 5 6

A V

COMPONENT IN

DMPORT

IN

PC IN

1 2

( SMARTLINK )

1

DC 5V 0.7A MAX

2

7

8

9

0

qa

IN3

qs

qd

qf

Equipment Optional Using

(Continued) 23 GB

Connect to							Input symbol on	Description
							screen
1	/					AV1	AV1	When you connect a decoder, the TV tuner outputs scrambled
								signals to the decoder, and the decoder unscrambles the
								signals before outputting them.
2	/					/	AV2	SmartLink is a direct link between the TV and a VCR/DVD
			AV2					recorder.
		(SMARTLINK)
3	/						Component	The component video sockets support the following video
	COMPONENT IN							inputs only: 480i, 480p, 576i, 576p, 720p, 1080i and 1080p.
4 DMPORT							DMPORT	You can play audio or video (optional cable required) of a
								portable audio player that is connected to the TV using a
								DIGITAL MEDIA PORT (DMPORT) adaptor.
								Depending on the connected DIGITAL MEDIA PORT
								adaptor, you can operate the connected equipment using the
								TV as follows;
								– Using the remote of the TV: N/x/X/m/M/F/f/G/
								g/ /	RETURN.
								– Using the Options menu function: Press OPTIONS, and
								select “Control Panel” or “Device Control (Menu).”
								~
								• Do not connect or disconnect a DIGITAL MEDIA PORT
								adapter while the TV is turned on.
								• The connected equipment is not charged when the TV is turned
								off or in standby mode.
5 HDMI IN 1 or 2							HDMI 1 or	Digital video and audio signals are input from the connected
							HDMI 2	equipment.
qs HDMI 3							HDMI 3	In addition, when you connect the equipment that is
								compatible with control for HDMI, communication with the

connected equipment is supported. See page 46 to set up this communication.

If the equipment has a DVI socket, connect the DVI socket to the HDMI IN socket through a DVI-HDMI adaptor interface (not supplied), and connect the equipment’s audio out socket to the audio in HDMI IN socket.

~

•The HDMI sockets support the following video inputs only: 480i, 480p, 576i, 576p, 720p, 1080i, 1080p and 1080/24p. For PC video inputs, see page 55.

•Be sure to use only an authorised HDMI cable bearing the HDMI logo.We recommend that you use a Sony HDMI cable (high speed type).

•When connecting an audio system that is compatible with control for HDMI, be sure to also connect it to the DIGITAL AUDIO OUT (OPTICAL) socket.

6

LAN

You can enjoy contents stored on DLNA-compatible devices

via a network (page 34).

7

/

PC IN

PC

It is recommended to use a PC cable with ferrites, such as the

“Connector, D-sub 15” (ref. 1-793-504-11, available in Sony

Service Centre) or equivalent.

8

L-

-R

Connect to the audio output sockets

to listen to the sound

from the TV on Hi-Fi audio equipment.

9

Use an optical audio cable.

DIGITAL AUDIO

OUT (OPTICAL)

24 GB

Connect to		Input symbol on Description
		screen
0	CAM	To use Pay Per View services.
	(Conditional	For details, refer to the instruction manual supplied with your
	Access Module)	CAM. To use the CAM, remove the dummy card from the
		CAM slot, then turn off the TV and insert your CAM card
		into the slot. When you are not using the CAM, we
		recommend that you keep the dummy card in the CAM slot.

~

•CAM is not supported in all countries. Please check with your authorised dealer.

qa	USB		You can enjoy photo/music files stored in a Sony digital still
			camera or camcorder through a USB cable or USB storage
			device on your TV (page 27).
qd	/L- -R	AV3	When connecting mono equipment, connect to the AV3
	AV3		L socket.
qf i			You can listen to TV sound through headphones.

Equipment Optional Using

25 GB

Viewing Pictures from Connected Equipment

Switch on the connected equipment, then perform one of the following operation.

For equipment connected to the scart sockets using a fully-wired 21-pin scart lead

Start playback on the connected equipment. The picture from the connected equipment appears on the screen.

For an auto-tuned VCR/ DVD recorder

In analogue mode, press PROG +/–, or the number buttons, to select the video channel.

For a USB device

See page 27.

For a Network device

See page 34.

For other connected equipment

Press / to display a list of connected equipment. Press F/f to select the desired input source, then press .

The highlighted item is automatically selected if you do not perform any operation for two seconds after pressing F/f.

If you have set an input source to “Skip” in the “AV Preset” menu (page 44), that input source does not appear in the list.

z

•To return to normal TV mode, press DIGITAL or

ANALOG.

Using the Options menu

Press OPTIONS to display the following options when viewing pictures from connected equipment.

Options	Description
Picture Mode (except	See page 39.
PC input mode)
Display Mode (in PC	See page 39.
input mode only)
Sound Mode	See page 40.
Surround	See page 40.
Speaker	See page 45.
Motionflow	See page 42.

Options	Description
PIP (in PC input	See page 27.
mode only)
PAP (except PC input	See page 26.
mode and DIGITAL
MEDIA PORT
mode)
Auto Adjustment (in	See page 44.
PC input mode only)
Horizontal Shift (in	See page 44.
PC input mode only)
Sleep Timer (except	See page 43.
PC input mode)
Power Saving	See page 41.
Device Control	See page 24.
(Menu) (in DIGITAL
MEDIA PORT mode
only)
Control Panel (in	See page 24.
DIGITAL MEDIA
PORT mode only)
Device Control (in	See page 30.
HDMI mode only)

To view two pictures simultaneously

– PAP (Picture and Picture)

You can view two pictures (external input and TV programme) on the screen simultaneously. Connect an optional equipment (page 23), and make sure that images from the equipment appear on the screen (page 26).

~

•This function is not available for a PC input and DIGITAL MEDIA PORT input.

•You cannot change the size of the pictures.

•You cannot display analogue TV video in the TV programme picture while displaying AV1, AV2 or AV3 video in the external inputs picture.

1Press OPTIONS.

2Press F/f to select “PAP”, then press .

The picture from the connected equipment is displayed on the left, and the TV programme is displayed on the right.

3Press the number buttons or PROG +/– to select the TV channel.

To return to single picture mode

Press RETURN.

z

•The highlighted picture is audible. You can switch the audible picture by pressing G/g.

26 GB

To view two pictures simultaneously

– PIP (Picture in Picture)

You can view two pictures (PC input and TV programme) on the screen simultaneously. Connect a PC (page 23), and make sure that image from a PC appear on the screen.

1Press OPTIONS to display the Options menu.

2Press F/f to select “PIP”, then press .

The picture from the connected PC is displayed in full size, and the TV programme is displayed in the small screen.

You can use F/f/G/g to move the TV programme screen position.

3Press number buttons or PROG +/– to select the TV channel.

To return to single picture mode

Press RETURN.

z

•You can switch the audible picture by selecting “Audio Swap” from the Options menu.

Playing Back Photo/Music via USB

You can enjoy photo/music files stored in a Sony digital still camera or camcorder through a USB cable or USB storage media on your TV.

1Connect a supported USB device to the TV.

2Press HOME.

3Press G/g to select “Photo” or “Music.”

4Press F/f to select a USB device, then press .

In “Music”, “List View” appears. In “Photo”, “Thumbnail View” appears. Press the yellow button to switch between “List View” and “Thumbnail View.”

5Press F/f/G/g to select a file or folder, then press .

When you select a folder, select a file, then press .

Playback starts.

Photo Playback Auto Start

The TV automatically starts photo playback when the TV is turned on and a digital still camera or other device storing photo files is connected to the USB port and then turned on (page 41).

(Photo) Available Options

Option	Description
Picture Mode	See page 39.
Sound Mode	See page 40.
Surround	See page 40.
Cropping	Crops a photograph.
Display map	Displays a map of the
	location where a photo
	was shot along with the
	photo itself.
Show Options	Allows you to set repeat/
	shuffle for photo
	playback.
Photo Set-up	Sets how playback should
	be performed and what
	effects to use during
	slideshows.
Rotate and Save	Rotates and saves
	unprotected files.

Equipment Optional Using

(Continued) 27 GB

Option	Description
Speaker	See page 45.
Picture Frame Image	Allows you to select a
	photograph to be
	displayed as picture
	frame.
Information	Displays information
	about the device, folders,
	and files.

(Music) Available Options

Option	Description
Sound Mode	See page 40.
Surround	See page 40.
Add to Slideshow	Registers the background
	music to be played during
	a slideshow using
	(Photo).
Omit from Slideshow	Cancels the registered
	background music.
Playback Options	Allows music options to
	be set for repeat, shuffle,
	or regular playback.
Speaker	See page 45.
Information	Displays information
	about the device, folders,
	and files.

~

•Picture quality may appear coarse when using (Photo) because images may be enlarged depending on the file. Also, images may not fill the entire screen depending on the image size and aspect ratio.

•Some photo files may take some time to be displayed when using (Photo).

•The file name and folder name support only English.

•While the TV is accessing the data on the USB device, observe the following:

–Do not turn off the TV or connected USB device.

–Do not disconnect the USB cable.

–Do not remove the USB device.

The data on the USB device may be damaged.

•Sony will not be held liable for any damage to, or loss of, data on the recording media due to a malfunction of any connected devices or the TV.

•Playback does not start automatically if the TV is turned on after connecting the digital still camera or other device to the USB port.

•USB playback is supported for the following photo file formats:

–JPEG (JPEG format files with the extension “.jpg” and conforming to DCF 2.0 or Exif 2.21)

–RAW (ARW/ARW 2.0 format files with this extension “.arw.”) For preview only.

•When you connect a Sony digital still camera, set the camera’s USB connection mode to Auto or “Mass Storage.” For more information about USB connection mode, refer to the instructions supplied with your digital camera.

•USB playback is supported for the following music file formats:

–MP3 (files with the extension “.mp3” that have not been copyrighted)

•USB Photo Viewer supports FAT12, FAT16 and FAT32 file systems.

•Depending on the exact file specifications, some files, including those modified on a PC, cannot be played even if the file format is supported.

•Check the website below for updated information about compatible USB devices. http://support.sony-europe.com/TV/compatibility/

To display a photograph

— Picture Frame

You can display a photograph on the screen for a selected period of time. After that period, the TV automatically switches itself into standby mode.

1Select a photograph.

You can select a photograph from the connected USB device or preset picture folder. For details on selecting a photograph, see page 27.

2Press OPTIONS while the selected photograph is displayed, then press F/f to select “Picture Frame Image” and press .

3Press RETURN repeatedly to return

to the Home Menu.

4Press F/f/G/g to select “Photo”, then select “Picture Frame” and press .

The TV is switched to Picture Frame mode, and the selected photograph is displayed on the screen.

To set the duration of displaying a photograph

Press OPTIONS, then select “Duration” and press . Then, select the duration, and press .

The counter appears on the screen.

To return to the XMB™

Press RETURN.

28 GB

~

•If the photograph is selected from a USB device, it must remain connected to the TV.

•If “Sleep Timer” is activated, the TV automatically will switch into standby mode.

To display a photograph with the location on the map

When using an image capture device with GPS function (digital still camera, etc.), it is possible to display a photograph with a map of the location where the photograph was taken using a function of GPS for recording longitude and latitude. Because map information is downloaded from the Internet online map service, the network connection must be required and the TV has to be connected to the network (page 34).

1Select a photograph (page 27).

2Press the green/red buttons to zoom in/out on the map.

To change the display position of the map on the TV screen, press the blue button repeatedly.

~

•Because the Internet online map service is provided by a third party, service may be changed or terminated without prior notification to the user.

•The position indicated on the map may differ depending on the image capture device.

•Only a large-scale map that cannot be zoomed in or out is displayed if the TV is not connected to the Internet or the Internet online map service is terminated.

•You can also display a slideshow with the location on the map. Set “Photo Set-up” to “Simple with map” (page 27).

z

•A map can be displayed in the case of photograph’s EXIF data includes a date information, and the associated longitude and latitude information (“Log files”) has been recorded using a Sony GPS unit. Follow the procedure described below.

1Connect the GPS unit to the USB port.

2Press HOME.

3Press G/g to select “Photo.”

4Press F/f to select the GPS unit, then press .

5Select the following items using F/f and press , then set them using F/f.

–Time Zone –DST

6Select “Yes”, then press . The GPS log files are loaded.

7Disconnect the GPS unit and connect the device on which the photograph is stored.

8Select a photograph (page 27).

9Press the green/red buttons to zoom in/out on the map.

Equipment Optional Using

29 GB

Using BRAVIA Sync with Control for HDMI

The control for HDMI function enables the TV to communicate with the connected equipment that is compatible with the function, using HDMI CEC (Consumer Electronics Control). For example, by connecting Sony equipment that is compatible with control for HDMI (with HDMI cables), you can control them together.

Be sure to connect the equipment correctly, and make the necessary settings.

Control for HDMI

•Automatically turns the connected equipment off when you switch the TV to standby mode using the remote.

•Automatically turns the TV on and switches the input to the connected equipment when the equipment starts to play.

•If you turn on a connected audio system while the TV is on, the sound output switches from the TV speaker to the audio system.

•Adjusts the volume (2 +/–) and mutes the sound (%) of a connected audio system.

•You can operate the connected Sony equipment that has the BRAVIA Sync logo by the TV remote by pressing:

–N/x/X/m/M to operate the connected equipment directly.

–SYNC MENU to display the menu of the connected HDMI equipment on the screen.

After displaying the menu, you can operate the menu screen by using F/f/G/g and .

–OPTIONS to display “Device Control”, then select options from “Menu”, “Options”, and “Content List” to operate the equipment.

–Refer to the instruction manual of the equipment for available control.

To connect the equipment that is compatible with control for HDMI

Connect the compatible equipment and the TV with a HDMI cable. When connecting an audio system, be sure to also connect the DIGITAL AUDIO OUT (OPTICAL) socket of the TV and the audio system using an optical audio cable. For details, see page 24.

To make the control for HDMI settings

The control for HDMI settings must be set on both the TV side and connected equipment side. See “HDMI Set-up” on page 46 for the TV side settings. For settings on the connected equipment, refer to the operating instructions for that equipment.

30 GB