O P E R A T I N G I N S T R U C T I O N S
|
|
AM/FM STEREO RECEIVER RX-4103 |
|
|
|
|
D A S |
|
|
|
|
|
|
|
|
|
VOLUME |
|
|
MEMORY T/P MODE |
|
|
|
|
TONE |
BALANCE |
|
|
|
REMOTE |
|
|
|
|
|
STANDBY |
|
|
SENSOR |
|
|
|
|
|
|
|
TUNING/PRESET |
|
|
|
|
|
|
|
|
FM/AM |
CD |
TAPE |
TV/AUX |
VCR |
TONE DIRECT |
|
ON/STANDBY |
|
|
|
|
|
|
|
|
PHONES |
|
|
|
|
|
|
|
|
A |
SPEAKER |
B |
|
|
|
|
|
|
RX-4103
AM/FM STEREO RECEIVER
ENGLISH
Introduction
UNPACKING AND INSTALLATION
Congratulations on Your Purchase!
Your new high fidelity receiver is designed to deliver maximum enjoyment and years of trouble free service. Please take a few moments to read this manual thoroughly. It will explain the features and operation of your unit and help ensure a trouble free installation. Please unpack your unit carefully. We recommend that you save the carton and packing material. They will be helpful if you ever need to move your unit and may be required if you ever need to return it for service. Your unit is designed to be placed in a horizontal position and it is important to allow at least two inches of space behind your unit for adequate ventilation and cabling convenience.
To avoid damage, never place the unit near radiators, in front of heating vents, in direct sunlight, or in excessively humid or dusty locations. Connect your complementary components as illustrated in the following section.
CAUTION |
RISK OF ELECTRIC SHOCK |
DO NOT OPEN |
CAUTION : TO REDUCE THE RISK OF |
ELECTRIC SHOCK, DO NOT |
REMOVE COVER (OR BACK). |
NO USER-SERVICEABLE PARTS |
INSIDE. REFER SERVICING TO |
QUALIFIED SERVICE PERSONNEL. |
This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING
To reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture.
Caution : Do not block ventilation openings or stack other equipment on the top.
FOR U.S.A.
Note to CATV System Installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
FCC INFORMATION
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
Caution regarding placement (Except for U.S.A. and Canada)
To maintain proper ventilation, be sure to leave a space around the unit (from
the largest outer dimensions including projections) equal to, or greater than, shown below.
Left and right panels: 5 cm
Rear panel: 10 cm
Top panel: 20 cm
2
READ THIS BEFORE OPERATING YOUR UNIT
FOR U.S.A. AND CANADA ................................. |
120 V |
FOR YOUR SAFETY
Units shipped to the U.S.A. and Canada are designed for operation on 120 V AC only.
Safety precaution with use of a polarized AC plug. However, some products may be supplied with a nonpolarized plug.
CAUTION : To prevent electric shock, match wide blade of plug to wide slot, fully insert.
ATTENTION : Pour eviter les choc electriques, introduire la lame la plug large de la borne correspondante de la prise et poussre jusqu’au fond.
FOR CHINA, EUROPE AND AUSTRALIA ........ |
220V/230V/240V |
FOR YOUR SAFETY
Units shipped to China are designed for operation on 220 V AC only.
Units shipped to Australia are designed for operation on 240 V AC only.
To ensure safe operation, the three-pin plug supplied must be inserted only into a standard three-pin power point which is effectively earthed through the normal household wiring. Extension cords used with the equipment must be three-core and be correctly wired to provide connection to earth.
Improper extension cords are a major cause of fatalities. The fact that the equipment operates satisfactorily does not imply that the power point is earthed and that the installation is completely safe. For your safety, if in any doubt about the effective earthing of the power point, consult a qualified electrician.
PAN-EUROPEAN UNIFIED VOLTAGE
All units are suitable for use on supplies 230-240 V AC.
FOR OTHER COUNTRIES ........................ |
115 V/230 V |
FOR YOUR SAFETY
Units shipped to countries other than the above countries are equipped with an AC voltage selector switch on the rear panel. Refer to the following paragraph for the proper setting of this switch.
AC VOLTAGE SELECTION
This unit operates on 115/230 V AC. The AC voltage selector switch on the rear panel is set to the voltage that prevails in the area to which the unit is shipped. Before connecting the power cord to your AC outlet, make sure that the setting position of this switch matches your line voltage. If not, it must be set to your voltage in accordance with the following direction.
AC voltage selector switch
AC 230 V |
|
|
|
|
AC 115 V |
|
|
|
|
||
|
|
|
|
||
|
|
|
Move switch lever to match your line voltage with a small screwdriver or other pointed tool.
ENGLISH
3
ENGLISH
CONTENTS |
|
Introduction |
|
UNPACKING AND INSTALLATION ....................................................................................................... |
2 |
READ THIS BEFORE OPERATING YOUR UNIT................................................................................... |
3 |
System Connections ....................................................................................................................................... |
5 |
Front Panel & Remote Controls ................................................................................................................. |
7 |
REMOTE CONTROL OPERATION RANGE ........................................................................................... |
9 |
LOADING BATTERIES ............................................................................................................................. |
9 |
Operations |
|
LISTENING TO A PROGRAM SOURCE ............................................................................................... |
10 |
LISTENING TO RADIO BROADCASTS ............................................................................................... |
12 |
RECORDING ............................................................................................................................................ |
14 |
OTHER FUNCTIONS ............................................................................................................................... |
14 |
Troubleshooting Guide ............................................................................................................................... |
15 |
Specifications ................................................................................................................................................. |
16 |
4
System Connections
Do not plug the AC input cord into the wall AC outlet until all connections are completed.
Be sure to connect the white RCA pin cord to the L(left) and the red RCA pin cord to the R(right) jacks when making audio connections.
Change the position of the FM indoor antenna until you get the best reception of your favorite FM stations. A 75 Ω outdoor FM antenna may be used to further improve the reception.
Disconnect the indoor antenna before replacing it with the outdoor one.
Place the AM loop antenna as far as possible from the receiver, TV set, speaker cords and the AC input cord and set it to a direction for the best reception.
If the reception is poor with the AM loop antenna, an AM outdoor antenna can be used in place of the AM loop antenna. Make connections firmly and correctly. If not, it can cause loss of sound, noise or damage to the receiver.
If the electricity fails or the AC input cord is left unplugged for more than 2 weeks, the memorized contents will be cleared. Should this happen, memorize them again.
ENGLISH
CD |
TV/AUX |
TAPE |
|
VCR |
|
IN |
OUT |
IN |
OUT |
ANTENNA
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and (2)This device must accept any interference received, including interference that may cause undesired operation.
|
SPEAKERS |
A |
SPEAKER IMPEDANCE |
|
A, B - 8 MIN / SPEAKERS |
|
A+B -16 MIN / SPEAKERS |
B |
|
AC INPUT 120V~60Hz 2.5A
MODEL NO. RX-4103
STEREO RECEIVER
MADE IN CHINA
DESIGNED IN USA
SER. NO
■ CONNECTING AUDIO/VIDEO COMPONENTS
■ CONNECTING ANTENNAS
CD player
FM
(OUTDOOR ANTENNA)
TV or additional component
AUDIO OUT
FM |
AM loop antenna |
|
(INDOOR ANTENNA) |
||
|
CD |
TV/AUX |
TAPE |
|
VCR |
|
IN |
OUT |
IN |
OUT |
AM
LOOP
Tape deck
PLAY(LINE) OUT
B A
REC(LINE) IN |
|
Video deck or MD recorder, etc. |
AUDIO OUT |
|
|
|
AUDIO IN |
•The VCR jacks may also be connected to an additional component such as MD recorder, tape deck, etc.
•The TV/AUX jacks may also be connected to an additional component such as a TV, DVD player, etc.
5
ENGLISH
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1)This device may not cause harmful interference, and
(2)This device must accept any interference received, MODEL NO. RX-4103 including interference that may cause undesired operation.
STEREO RECEIVER
MADE IN CHINA
DESIGNED IN USA
|
|
|
|
|
SPEAKERS |
SER. NO |
CD |
TV/AUX |
TAPE |
|
VCR |
|
|
|
IN |
OUT |
IN |
OUT |
A |
SPEAKER IMPEDANCE |
|
|
|
|
|
||
|
|
|
|
|
|
A, B - 8 MIN / SPEAKERS |
|
|
|
|
|
|
A+B -16 MIN / SPEAKERS |
|
|
|
|
|
B |
|
ANTENNA
■ CONNECTING SPEAKERS
Speaker A
Right |
Left |
SPEAKERS
A
B
■ AC INPUT CORD
Plug this cord into a wall AC outlet.
Right |
Left |
Speaker B
•Usually SPEAKER A terminals are used for only a pair of speakers. When you have another pair of speakers, SPEAKER B terminals can be used.
•Never short-circuit the + and - speaker cords.
•Be sure to connect speakers firmly and correctly according to the channel (left and right) and the polarity (+ and -).
Note :
•For safe amplifier operation, use the speakers with impedance of over 8Ω when you use only SPEAKER A or B terminals and use the speakers with impedance of over 16Ω when you use both SPEAKER A and B terminals.
6
Loading...