Samsung WA48H7400AW/A2 User Manual

WA48H7400A*

WA45H7200A*

WA45H7000A*

Washing Machine

user manual

This manual is made with 100% recycled paper.

Imagine the possibilities

Thank you for purchasing this Samsung product.

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 1				2015/12/22 15:10:06

contents

installing your washer

10

operating instructions

17

washing a load of laundry

18

10Unpacking your washer

10Overview of your washer

11Basic location requirements

11	Electrical
11	Grounding

11Water

12Drain facility

12 Flooring

12Location considerations

12Alcove or closet installation

13Required dimensions for Installation

13Important note to installer

17Loading your washer

17Getting started

18Overview of the control panel

20Child Lock [ ]

21	Sound
21	Garment
21	Delay End
21	Pre Soak

21AquaJetTM

22Mist Shower

22Smart Care

23Washing clothes using the cycle selector

23ATC (Auto Temperature Control)

24Detergent use

24 Features

maintaining your washer	27	Cleaning the exterior
27	27	Cleaning the interior
	27	Storing your washer
	27	Preserving the top cover and the front frame
	28	Cleaning the dispensers
	29	Self Clean
troubleshooting	30	Check these solutions if your washer…
30	32	Information codes
appendix	34	Fabric care chart
34	35	Cycle chart
	38	Helping the environment
	38	Declaration of conformity
	38	Specification

English - 2

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 2		2015/12/22 15:10:06

safety information

Congratulations on your new Samsung Washer. This manual contains important information on the installation, use, and care of your appliance. Please take time to read this manual to take full advantage of your washer’s many benefits and features.

What you need to know about safety instructions

Warnings and Important Safety Instructions in this manual do not cover all possible conditions and situations that may occur. It is your responsibility to use common sense, caution, and care when installing, maintaining, and operating your washer.

Important safety symbols and precautions

What the icons and signs in this user manual mean:

		Hazards or unsafe practices that may result in severe personal injury
		or death.
	WARNING	To reduce the risk of fire, explosion, electric shock, or personal injury
		when using your washer, follow these basic safety precautions:
		Hazards or unsafe practices that may result in minor personal injury or
	CAUTION	property damage.

Do NOT attempt.

Do NOT disassemble.

Do NOT touch.

Follow directions explicitly.

Unplug the power plug from the wall socket.

Make sure the machine is grounded to prevent electric shock.

Call the service center for help.

Note

These warning icons are here to prevent injury to you and others.

Please heed them explicitly.

After reading this section, keep it in a safe place for future reference.

Read all instructions before using the appliance.

SAVE THESE INSTRUCTIONS

English - 3

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 3		2015/12/22 15:10:06

safety information

WARNING

WARNING State of California Proposition 65 Warning (US only)

This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

WARNING Important safety precautions

To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following:

1.Read all instructions before using the appliance.

2.Do not wash or dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, other flammable or explosive substances as they give off vapors that could ignite or explode.

3.Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children.

4.Before the appliance is removed from service or discarded, remove the lid of the washing or drying compartment.

5.Do not reach into the appliance if the drum is moving.

6.Do not install or store this appliance where it will be exposed to the weather.

7.Do not tamper with the controls.

8.Do not repair or replace any part of the appliance or attempt any servicing unless it is specifically recommended in the user-maintenance instructions or in published userrepair instructions that you understand and have the skills to carry out.

9.Do not add gasoline, dry-cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

10.Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for 2 weeks or more, before using a washer or combination washer-dryer, turn on all hot water faucets and let the water flow from

each for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.

SAVE THESE INSTRUCTIONS

English - 4

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 4		2015/12/22 15:10:06

WARNING CRITICAL INSTALLATION WARNINGS

Plug the power cord into an AC 120 V / 60 Hz/wall socket rated at 15 amps or higher. Use the socket for this appliance only. In addition, do not use an extension cord.

-Sharing a wall socket with other appliances, using a power strip, or extending the power cord may result in electric shock or fire.

-Do not use an electric transformer. It may result in electric shock or fire.

-Ensure that the power voltage, frequency, and current match the product’s specifications. Failing to do so may result in electric shock or fire.

Have this appliance installed by a qualified technician or service company.

-Failing to do so may result in electric shock, fire, an explosion, problems with the product, or injury.

Remove all foreign substances such as dust or water from the power plug terminals and contact points using a dry cloth on a regular basis.

-Unplug the power plug and clean it with a dry cloth.

-Failing to do so may result in electric shock or fire.

Plug the power plug into the wall socket in the right direction so that the cord runs towards the floor.

-If you plug the power plug into the socket in the opposite direction, the electric wires within the cable may be damaged and this may result in electric shock or fire.

This appliance must be properly grounded.

Do not ground the appliance to a gas pipe, plastic water pipe, or telephone line.

-Improper grounding may result in electric shock, fire, an explosion, or problems with the product.

-Never plug the power cord into a socket that is not grounded correctly. Make sure the socket you use is grounded in accordance with local and national codes.

Do not install this appliance near a heater or flammable material.

Do not install this appliance in a humid, oily, or dusty location, or in a location exposed to direct sunlight or water (rain drops).

Do not install this appliance in a location where gas may leak. - This may result in electric shock or fire.

Plug the power plug into the wall socket firmly. Do not use a damaged power plug, damaged power cord, or loose wall socket.

- This may result in electric shock or fire.

Do not pull or excessively bend the power cord. Do not twist or tie the power cord.

Do not hook the power cord over a metal object, place a heavy object on the power cord, insert the power cord between objects, or push the power cord into the space behind the appliance.

- This may result in electric shock or fire.

Do not pull the power cord when unplugging the power plug.

-Unplug the power plug by holding the plug.

-Failing to do so may result in electric shock or fire.

If the power plug or power cord are damaged, contact your nearest service center.

SAVE THESE INSTRUCTIONS

English - 5

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 5		2015/12/22 15:10:07

safety information

CAUTION INSTALLATION CAUTIONS

Position the appliance so that the power plug is easily accessible.

- Failing to do so may result in electric shock or fire due to electric leakage.

Install your appliance on a level and hard floor that can support its weight.

- Failing to do so may result in abnormal vibrations, noise, or problems with the product.

Unplug the power plug when the appliance is not being used for long periods of time or during a thunder/lightning storm.

- Failing to do so may result in electric shock or fire.

WARNING CRITICAL USAGE WARNINGS

If the appliance is flooded, cut the power immediately and contact your nearest service center.

If the appliance emits a strange noise, a burning smell, or smoke, unplug the power plug immediately and contact your nearest service center.

- Failing to do so may result in electric shock or fire.

In the event of a gas leak (such as propane gas, LP gas, etc.), ventilate the area immediately. Do not turn any appliance or light on or off.

-Do not use a ventilating fan.

-A spark may result in an explosion or fire.

Do not wash items contaminated with gasoline, kerosene, benzene, paint thinner, alcohol or other flammable or explosive substances.

- This may result in electric shock, fire, or an explosion.

Do not force the washer lid open while the washer is operating (high-temperature washing/ drying/spinning).

-Water flowing out of the washer may cause burns or cause the floor to be slippery. This may result in injury.

-Forcing the lid open can damage the product or cause injury.

Make sure to remove the packaging (sponge, styrofoam) attached to the bottom of the washer before using it.

Do not insert your hand under the washer. - This may result in injury.

SAVE THESE INSTRUCTIONS

English - 6

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 6		2015/12/22 15:10:07

Do not touch the power plug with wet hands. - This may result in electric shock.

Do not turn the appliance off by unplugging the power plug while the washer is in operation.

-Plugging the power plug into the wall socket again may cause a spark and result in electric shock or fire.

Keep all packaging materials well out of the reach of children, as packaging materials can be dangerous to children.

- If a child places a bag over their head, the child may suffocate.

Do not let children or infirm persons use this washer unsupervised. - Failing to do so may result in electric shock, burns or injury.

Do not insert your hand or a metal object under the washer while it is operating. - This may result in injury.

Do not attempt to repair, disassemble, or modify the appliance yourself.

-Do not use any fuse (such as copper, steel wire, etc.) other than the standard fuse.

-If you need to repair or reinstall the appliance, contact your nearest service center.

-Failing to do so may result in electric shock, fire, problems with the product, or injury.

If any foreign substance such as water enters the appliance in any area other than the tub, unplug the power plug and contact your nearest service center.

- Failing to do so may result in electric shock or fire.

If the water supply hose comes loose from the faucet and floods the appliance, unplug the power plug.

- Failing to do so may result in electric shock or fire.

CAUTION USAGE CAUTIONS

If the washer is contaminated by a foreign substance such as detergent, dirt, food waste, etc., unplug the power plug and clean the washer using a damp, soft cloth.

- Failing to do so may result in discoloration, deformation, damage or rust.

The clear portion of the lid can be broken by a strong impact. Take care when using the washer.

- If the clear portion is cracked or broken, it may result in injury.

After a water supply failure or when reconnecting the water supply hose, open the faucet slowly.

Open the faucet slowly after a long period of non-use.

-The air pressure in the water supply hose or the water pipe may result in damage to a part or in water leakage.

If a drain error occurs during an operation, check if there is a draining problem.

-If the washer is used when it is flooded because of a draining problem, it may result in electric shock or fire due to electric leakage.

Do not insert your hand under the washer. - This may result in injury.

SAVE THESE INSTRUCTIONS

English - 7

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 7		2015/12/22 15:10:07

safety information

Insert the laundry into the washer completely so that laundry does not get caught in the lid.

-If laundry gets caught in the lid, it may result in damage to the laundry or the washer, or result in water leakage.

Ensure that the faucet is turned off when the washer is not being used.

-Ensure that the water supply hose connectors are properly tightened.

-Failing to do so may result in property damage or injury.

Open the faucet and check if the water supply hose connector is firmly tightened and that there is no water leaking before using the product.

- If the water supply hose connectors are loose, it may result in water leakage.

Do not stand on top of the appliance or place objects (such as laundry, lighted candles, lighted cigarettes, dishes, chemicals, metal objects, etc.) on the appliance.

- This may result in electric shock, fire, problems with the product, or injury.

Do not operate the appliance with wet hands. - This may result in electric shock.

Do not spray volatile material such as insecticide onto the surface of the appliance.

-As well as being harmful to humans, it may also result in electric shock, fire, or problems with the product.

Do not place an object that generates a electromagnetic field near the washer. - This may result in injury due to a malfunction.

Since the water drained during a high-temperature wash or drying cycle is hot, do not touch the water.

- This may result in burns or injury.

For waterproof fabrics, only use the WATERPROOF cycle. - Do not use other cycles for waterproof fabrics.

*This may result in injury or damage to the washer, walls, floor, or clothing due to abnormal vibrations.

- Set the temperature and spin according to the attached care label.

Do not operate the washer when detergent dispenser is removed. - This may result in electric shock or injury due to water leakage.

Do not insert your hand into the detergent dispenser after opening it. - This may result in injury as your hand may be caught.

SAVE THESE INSTRUCTIONS

English - 8

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 8		2015/12/22 15:10:07

Do not place any non-laundry objects, such as shoes, food waste, or animals into the washer.

-This can cause abnormal vibrations that can damage the washer, and, in the case of pets, cause severe injury or death.

Do not press the buttons using sharp objects such as pins, knifes, fingernails, etc. - This may result in electric shock or injury.

Do not wash laundry contaminated by oils, creams, or lotions usually found in skincare shops or massage clinics.

- This may result in the rubber seal becoming deformed and water leakage.

Do not leave metal objects (safety pins, hair pins, etc.) or bleach in the tub for long periods of time.

-This may cause the tub to rust.

-If rust appears on the surface of the tub, apply a neutral cleansing agent to the surface and use a sponge to clean it. Never use a metal brush.

Do not use dry cleaning detergent directly and do not wash, rinse, or spin laundry contaminated by dry cleaning detergent.

-This may result in spontaneous combustion or ignition due to heat from the oxidation of the oil.

Do not use hot water from water cooling/heating devices. - This may result in problems with the washer.

Do not use natural hand-washing soap in the washer.

-If it hardens and accumulates inside the washer, it may cause problems with the product, discoloration, rust, or bad odors.

Do not wash large laundry items such as bedding in the washing net.

-Failing to do so may result in injury due to abnormal vibrations.

-Place smaller items, such as lace socks and lingerie in the washing net.

Do not use hardened detergent.

- If it accumulates inside the washer, it may result in water leakage. Do not wash throw rugs or doormats.

-If you wash throw rugs or doormats, the sand will accumulate inside the washer. It may result in error such as no draining.

WARNING CRITICAL CLEANING INSTRUCTIONS

Do not clean the appliance by spraying water directly onto it. Do not use the strong acid cleaning agent.

Do not use benzene, thinner, or alcohol to clean the appliance.

- This may result in discoloration, deformation, damage, electric shock, or fire.

Before cleaning or performing maintenance, unplug the appliance from the wall socket. - Failing to do so may result in electric shock or fire.

SAVE THESE INSTRUCTIONS

English - 9

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 9		2015/12/22 15:10:07

installing your washer

Unpacking your washer

Unpack your washer and inspect it for shipping damage. Make sure you have received all the items shown below. If your washer was damaged during shipping, or you do not have all of the items, contact 1-800-SAMSUNG (1-800-726-7864).

To prevent personal injury or strain, wear protective gloves whenever lifting or carrying the unit.

WARNING

CAUTION

Packing materials can be dangerous to children; Keep all packing material (plastic bags, polystyrene, etc.) well out of children’s reach.

When unpacking the washing machine, 2 person collaboration is needed. To remove the cushion bottom of the packing materials, forward dumping is strictly prohibited.

Overview of your washer

Drain Hose	Control panel
	Lid
Power Cord

Adjustable legs

Parts supplied

Hose guide

User manual book

Plastic zip hose tie

Water intake cap

Tools needed

Wrench Flat screwdriver Level

Parts not supplied

	• If you lose an accessory and want to purchase a replacement, contact the
	Samsung service center (1-800-SAMSUNG (1-800-726-7864)).
	• The design of the parts and accessories may differ from the pictures above.
	Their design is subject to change without notice for product improvement.
Water supply hoses	• Do not reuse old hoses. Only use new water supply hoses when you install the
	washing machine. Old water supply hoses can leak or burst causing flooding
	and property damage.
	• Confirm that there are rubber washers inside each coupling of the water
	supply hoses.
	English - 10

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 10		2015/12/22 15:10:08

Basic location requirements

Electrical

•120 Volt 60 Hz 15 AMP fuse or circuit breaker.

•Individual branch circuit serving only your Washer is recommended.

•Your Washer is equipped with a power cord.

NEVER USE AN EXTENSION CORD.

CAUTION

Grounding

ELECTRICAL GROUNDING IS REQUIRED FOR THIS APPLIANCE.

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.

This appliance is equipped with a power cord having a three-prong grounding plug for use in a properly installed and grounded outlet.

The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

An improperly connected equipment-grounding conductor can increase the risk of electrical WARNING shock. Check with a qualified electrician or serviceman if you are not sure whether the

appliance is properly grounded. Do not modify the plug provided with the appliance – if it does not fit the outlet, have a proper outlet installed by a qualified electrician.

IMPORTANT SAFETY PRECAUTIONS

•To prevent unnecessary risk of fire, electrical shock or personal injury, all wiring and grounding must be done in accordance with the National Electrical Code ANSI/FNPA, No. 70 Latest Revision and local codes and ordinances. It is the personal responsibility of the appliance owner to provide adequate electrical service for this appliance.

NEVER CONNECT THE GROUND WIRE TO PLASTIC PLUMBING LINES, GAS LINES, OR CAUTION HOT WATER PIPES.

Water

To correctly fill your Washer in the proper amount of time, water pressure of 20 to 116psi (137 to 800kPa) is required.

Water pressure less than 20 psi may cause water valve failure, or may not allow the water valve to shut off completely, or may extend the fill time beyond what your Washer controls allow, causing your Washer to turn off. A time limit is built into the controls to prevent flooding in your home if a hose becomes loose.

The water faucets must be within 4 feet / 122 cm of the back of your Washer to match the inlet hoses provided with your Washer.

Accessory inlet hoses are available in various lengths up to 10 feet / 275 cm for faucets that are further away from the back of your Washer.

To avoid the possibility of water damage:

•Have water faucets easily accessible.

•Turn off faucets when the washer is not in use.

•Periodically check that there is no leakage from the water inlet hose fittings.

WARNING CHECK ALL CONNECTIONS AT THE WATER VALVE AND FAUCET FOR LEAKS.

English - 11

washer your installing 01

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 11		2015/12/22 15:10:08

installing your washer

Drain facility

The recommended height of the standpipe is 39 in / 99 cm. The drain hose must be routed through the drain hose clip to the standpipe. The standpipe must be large enough to accept the outside diameter of the drain hose. The drain hose is attached to the washer at the factory.

Flooring

For best performance, you must install your washer on a solidly constructed floor. Wood floors may need to be reinforced to minimize vibration and/or unbalanced load situations. Carpeting and soft tile surfaces are contributing factors to vibration which can cause your washer to move slightly during the spin cycle.

Never install your washer on a platform or weakly supported structure.

Location considerations

Do not install your washer in areas where water may freeze, since your washer will always retain some water in its water valve, pump, and hose areas. Frozen water can damage the belts, the pump, hoses, and other components.

Alcove or closet installation

MINIMUM CLEARANCES FOR CLOSET AND ALCOVE INSTALLATIONS:

Sides – 1 in / 25 mm	Closet Front – 2 in / 51 mm
Rear – 6 in / 152 mm	TOP - 21 in / 533 mm
Gap between end of water valve and the wall

-Case 1. Assemble supply hose after installing : Over 3.9 in (10 cm).

-Case 2. Assemble supply hose before installing : Over 2.8 in (7cm).

If the washer and dryer are installed together, the closet front must have at least a 72 in² (465 cm²) unobstructed air opening. Your washer alone does not require a specific air opening.

A		1 in.
		(2.5 cm)
1 in.	27.0 in.	27.0 in.	1 in.
(2.5 cm)	(68.6 cm)	(68.6 cm)	(2.5 cm)

B
	21 in.
	(53.3 cm)
		Case 1.	3.9 in. (10 cm)
		Case 2.	2.8 in. (7 cm)
2 in.	29.3 in.	6 in.
(5.1 cm)	(74.4 cm)	(15.2 cm)

A.Recessed area

B.Side view - closet or confined area

English - 12

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 12		2015/12/22 15:10:08

Required dimensions for Installation

		29.3 in.
		(74.4 cm)
	43.9 in.
	(111.5 cm)
	39.3 in.	43.9 in.
	(99.8 cm)
		(111.5 cm)
	27.0 in.	29.3 in.
		(74.4 cm)
	(68.6 cm)

58.1 in.

(147.6 cm)

*Required spacing

		3 in.
	48 in.² *	(7.6 cm)
	(310 cm²)
	24 in.² *	3 in.
	(155 cm²)
		(7.6 cm)
		Closet or Door

Important note to installer

Please read the following instructions carefully before installing your washer.

These instructions should be retained for future reference.

We recommend you hire a professional to install this washer.

Installation Flow chart

Selecting

Removing the

Connecting the water

Adjusting the

Powering your

shipping bolts

a location

and the drain

levelling feet

washing machine

(*Drum only)

[Running a test cycle]

Does a

Running

Run a test cycle(Rinse+Spin)

Finish the

Laundary machine

a Calibration

with small

amount of laundary

No

installation

Vibrate?

mode

(about 4~5 Towels)

Yes

Please check again before steps.

STEP 1 Selecting a Location

Before you install the washer, make sure the location:

•Has a hard, level surface without carpeting or flooring that may obstruct ventilation.

•Is away from direct sunlight.

•Has adequate ventilation.

•Is not exposed to freezing temperatures (temperatures under 32 °F or 0 °C).

•Is away from heat sources such as oil or gas.

•Has enough space so that the washer doesn’t rest on its power cord.

English - 13

washer your installing 01

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 13		2015/12/22 15:10:09

installing your washer

STEP 2

Connecting the water and the drain

Connecting the water supply hose

Before installing the water supply hoses, make sure there are CAUTION rubber gaskets inside the fittings at both ends of each new

water hose. Installing the water supply hoses without rubber gaskets can cause water leakage.

When you initially install the washer, be sure to use new hoses. CAUTION Failing to do so may result in a water leakage or overflow and

may damage your property.

Do not connect multiple water supply hoses together to	Coupling				Rubber Washer
CAUTION increase the length of the supply hose. Hoses connected this
way can leak and the leakage can cause electrical shock. If a
hose is too short, replace the hose with a longer, high pressure
hose.

1.	Connect the ends of the water supply hoses to the HOT and COLD faucets. Cold	Hot
2.	Tighten the fittings by hand until they are snug, and then tighten them an
	additional two-thirds of a turn with a wrench.

When you fasten the fittings, do not fasten them too tightly or apply

CAUTION tape or sealant to the faucets or water supply intakes. This can damage the fittings.

After you have connected the water supply hoses to the faucets, ensure that they are connected correctly by pulling the water supply hoses downwards

3.Place the unconnected ends of the hoses into a bucket and open the faucets connected to the two water supply hoses for 10 or 15

seconds to remove any foreign substances from the hoses. Close the faucets before continuing.

4. Connect the ends of the water supply hoses to the water supply intake connections at the back of the washer.

The water supply hose connected to the HOT faucet must be CAUTION connected to the hot water supply intake and the water hose

connected to the COLD faucet must be connected to the COLD water supply intake.

5. Tighten the fittings by hand until they are snug, and then tighten them an additional two-thirds of a turn with a wrench.

To ensure the correct water usage, connect both the HOT and COLD water faucets. If either or both are not connected, an “4E” (no fill) error can occur.

If you do not want to use the HOT water supply hose, insert the water intake cap into the HOT water supply intake hole. In this case, you must select the Tap Cold option for the water temperature. If you select the Tap Cold option, all the lamps for the water temperature options are turned off.

Confirm that the water supply hoses are not twisted or bent. If CAUTION the hoses are twisted or bent, the hoses can leak and cause

electric shock due to the water leakage.

6. Turn on the HOT and COLD water supplies and check all the water supply intake connections and the faucets for water leaks.

English - 14

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 14		2015/12/22 15:10:10

Connecting the drain hose
The end of the drain hose can be positioned in
three ways:
Over the edge of a wash basin
Secure the guide to the side of the basin wall
with a hook or to the tap with a piece of string to
prevent the drain hose from moving.	Laundry tub		Stand pipe
In a standpipe or laundry tub		Hose
The standpipe must be no shorter than 39 in (99		retainer
cm) and no longer than 96 in (245 cm).	96” Max				39” Min
	39” Min
Make sure that the connection between the		Tie			(99 cm)
drain hose and the standpipe is not airtight.		strap

Connection the hose guide within 4 in (10cm) from the end of the drain hose. If the drain hose is

extended more than 4 in (10cm) beyond the end of the hose guide, mold or microorganisms could spread to the inside of the washer.

Drain Hose can be installed until 96 in (245cm) maximum. But drain capability can be reduced at this height. It causes the washer to have odor, because of remained water in the drain system.

If the drain hose is installed below 39 in (99 cm), water can be drained in cycles due to a siphon phenomenon. It causes the washer to display a “4E” error code.

1RPRUHWKDQLQ FP

+RVH*XLGH

STEP 3

Leveling your washer

See if the washer is level by checking the position of the tub:

1.Slide the washer into position.

2.Open the lid of the washer, and pour the water into the tub to just below the pulsator level.

Pulsator

Loosen Lock

Adjustable legs (three)

3.If the washer is level, the pulsator is positioned at the center of the water as shown in the figure. If not, level your washer by turning the front leveling feet clockwise or counterclockwise as necessary.

Turn the front leveling feet clockwise to raise the washer, and counterclockwise to lower the washer.

English - 15

washer your installing 01

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 15		2015/12/22 15:10:11

installing your washer

STEP 4

Powering your washer

Plug the power cord into a 3-prong, well grounded 120 volt 60

Hz approved electrical outlet protected by a 15-amp fuse or comparable circuit breaker.

Your washer is grounded through the third prong of the power cord when plugged into a three-prong grounded electrical outlet.

Test run

Make sure that you install your washing machine correctly by running the Rinse+Spin cycle after the installation is complete.

STEP 5

Running a test cycle

Run a test cycle as follows to check if your washer is properly installed.

1.Load about 6 pounds of laundry into the tub.

2.Press the Power button to turn on your washer.

3.Select the Rinse+Spin cycle by turning the Cycle Selector.

4.Press the Start/Pause button to start the test cycle.

5.The washer should not rock or vibrate excessively when water is supplied or when washing or spinning, and should drain well during the spin cycle.

If water leaks while water is being supplied or drained, check the water connections. Refer to the “Connecting the water and the drain” section on pages 14~15 for instructions.

If the washer rocks and vibrates excessively, level your washer again. Refer to the “Leveling your washer” section on page 15 for instructions.

STEP 6

Calibration mode

Your Samsung washing machine detects the laundry weight automatically.

For more accurate weight detection, please run Calibration Mode after the installation. To run Calibration Mode, follow these steps:

1.Remove laundry or any contents in the machine.

2.Press the Temp. and Delay End buttons simultaneously, and then press the Power button. The machine turns on.

3.Press the Start/Pause button to activate “Calibration Mode”.

4.The pulsator rotates clockwise and counterclockwise for approximately 1 minute.

5.When “Calibration Mode” is finished, “End” (WA48H7400A*, WA45H7200A*) / “0” (WA45H7000A*)

appears on the display, and the machine automatically turns off. The washing machine is now ready for use.

English - 16

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 16		2015/12/22 15:10:11

operating instructions

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using your appliance, WARNING follow basic precautions, including the following:

Loading your washer

• Fill the tub with dry, unfolded clothes evenly around in order to enhance washing efficiency and prevent

excess wear, or wrinkling of the load.
- For optimal washing performance, make sure the laundry is piled up evenly.	02
• Wash delicate items such as bras, hosiery, and other lingerie in the Delicates cycle with similar	instructions operating
lightweight items.
• When washing big bulky items or a few smaller items that don’t fill the tub completely – a rug, a pillow,
stuffed toys, or one or two sweaters, for example – add a few towels to improve spin performance.
• Do not insert bulky items except for Bedding in this cycle.

During the spin cycle, the washer may add additional water to redistribute the clothes and correct an imbalance inside the drum.

•When washing heavily soiled loads, do not overload your washer to ensure good cleaning results.

•To add a forgotten item:

1.Press the Start/Pause button to pause the washer.

2.Wait for the door to unlock automatically, and then open the door.

3.Add the item, close the door, and then press the Start/Pause button. The cycle will resume.

Getting started

1.Load your washer.

2.Add liquid (or powder) detergent and additives to the dispenser (see pages 24~26).

3.Select the appropriate cycle and options for the load (see pages 18~23).

4.Close the lid.

5.Press the Start/Pause button.

6.The Wash Indicator light illuminates.

7.The estimated cycle time will appear in the display.

The time may fluctuate to indicate the time remaining in the cycle better.

The actual time required for a cycle may differ from the estimated time in the display depending on the water pressure, water temperature, detergent, and laundry.

8.Before your washer starts to fill, it will make a series of clicking noises to check the door lock and do a quick drain.

•When the cycle is complete, the Door Lock light will go out and “End” (WA48H7400A*, WA45H7200A*) / “0” (WA45H7000A*) will appear in the display.

•Pressing the Power button cancels the cycle and stops your washer.

•The Wash, Rinse , and Spin indicator lights will illuminate during those portions of the cycle.

English - 17

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 17		2015/12/22 15:10:11

washing a load of laundry

Overview of the control panel

WA48H7400A*

WA45H7200A*

WA45H7000A*

Select the appropriate cycle for the type of load.

		The cycle you select determines the tumble pattern and spin speed for
		the cycle.
		To minimize wrinkling of laundry, select the Perm Press cycle.
		NORMAL - For most fabrics including cottons, linens, and normally
		soiled garments.
		HEAVY DUTY - For sturdy, colorfast fabrics and heavily soiled garments.
		COLORS/DARKS (WA48H7400A*, WA45H7200A*) - For brightly or
	1 Cycle Selector	dark colored casual garments.
		BEDDING - For bulky and large items, such as comforters, blankets and
		sheets.
		When washing comforters, use liquid detergent.
		Waterproof sheets and all water resistant items should be washed using
		the waterproof cycle.

Use the waterproof cycle for waterproof or water-resistant items such as mattress covers, plastic mats, ski pants, raincoat and comforters which hardly absorb water.

DELICATES - For sheer fabrics, bras, lingerie, silks, and other handwash-only fabrics. For best results, use liquid detergent.

English - 18

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 18		2015/12/22 15:10:12

			WATERPROOF - For waterproof or water-resistant items.
			 Do not wash waterproof items and non-waterproof items together.
			 Check the specification label on the fabric item and see if the
			item is waterproof. Do not wash non-waterproof items with the
			WATERPROOF cycle.
			PERM PRESS - For wash-and-wear, synthetic fabrics, and lightly to normally
			soiled garments.
			ACTIVE WEAR (WA48H7400A*, WA45H7200A*) - Use this cycle to wash exercise
			wear such as sports jerseys, training pants, shirts/tops and other performance
			clothing. This cycle provides effective soil removal with gentle action for special
			fabric care.
			QUICK WASH - For lightly soiled garments needed quickly.
			SPIN - Drains the water and spins at a high speed.
			RINSE + SPIN - Use for loads that need rinsing only or to add rinse-added
			fabric softener to a load.
	2	Display	Provides instructions and diagnostics while keeping you updated on the cycle
			status and time remaining.
			Press the button repeatedly to cycle through the different water temperature options.
			Hot - Whites and heavily soiled, colorfast items.
			Warm - Colorfast items.
	3	Temp. selection	Eco Warm - Moderately soiled, colorfast items; most wrinkle-free items.
		button	Cold - Brightly colored, very lightly soiled items.
			Tap Cold - Cold water with no warm water added.
			 If you select the Tap Cold option, all the lamps for the water temperature
			options are turned off.
			Press the button repeatedly to cycle through the different spin speed options.
			High - Use for underwear, t-shirts, jeans, and sturdy cottons.
	4	Spin selection	Medium - Use for jeans, wrinkle-free or wash-and-wear items, and synthetics.
		button	Low - Use for delicate items needing a slow spin speed.
			No Spin - Drains your washer without spinning. Use for extremely delicate items
			that cannot tolerate any spin.
		Soil Level	Press the button to select the soil level/washing time.
	5		Heavy - For heavily soiled loads.
		selection button	Normal - For moderately soiled loads. This setting is best for most loads.
			Light - For lightly soiled loads.
			Press these buttons to select different cycle options.
			AquaJetTM Deep Clean (WA48H7400A*) - Improve washing performance
			through longer AquaJet spray action. Water Level can be adjusted.
			AquaJetTM (WA45H7200A*) - Improves the washing & rinsing performance using
			falling water.
	6	Select Cycle	Extra Rinse (WA45H7000A*) - Change from spray rinse mode to deep rinse
		Option	mode, and rinse once again.
			Delay End - Delay the end of any cycle for up to 19 hours in one-hour
			increments. Displayed hour indicates the time the wash will be ended.
			Self Clean - Use to clean dirt and bacteria from the drum. Regular use (after
			every 40 washes) is recommended. No detergent or bleach is needed.
			Pre Soak - It adds 15 minutes soaking time at the start of the wash cycle for
			better stain removal.
	7	Start/Pause	Press to pause and restart cycles.
		selection button
		Power button	Press once to turn your washer on. Press again to turn your washer off. If the
	8		washer is left on for more than 10 minutes without any buttons being pressed, the
			power automatically turns off.
			English - 19

laundry of load a washing 03

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 19		2015/12/22 15:10:12

washing a load of laundry

Child Lock [ ]

Child Lock prevents children from playing with your washer.

Activating the Child Lock function

Press and hold the Spin and Soil Level buttons simultaneously for approximately 3 seconds.

•When you activate the Child Lock function, the “Child Lock [ ]” lamp blinks.

Using the Child Lock function

If the lid is opened when the Child Lock function is on, “dE” is displayed and an alarm sounds.

•If the water level in the tub is above the safe water level, “dE” is displayed on the LED display and the washing machine starts to drain water by force after 30 seconds.

•If the water level in the tub is above the safe water level and the Child Lock function is turned on while the door is open, “CL” is displayed on the LED display even if the power of the washing machine is turned off and the washing machine drains water by force.

•Even if the power of the washing machine is turned off, if the lid is opened while the water level in the tub is above the Reset water level, “CL” is displayed on the LED display without the alarm sounding and the washing machine starts to drain water. When the draining operation finishes, the power is automatically turned off again.

•You have activated the Child Lock function while the washing machine is running, the Start/ Pause button will not work.

•After the compulsory drain, the “CL” code display blinks at 1 second intervals and the product enters the “CL” mode. (When the product is in the “CL” mode, only the Power button works.)

•To cancel the “CL” mode, you need to turn the power off and then on again.

•To cancel the “dE” mode, deactivate the Child Lock function. To deactivate the Child Lock function, press and hold the Spin and Soil Level buttons simultaneously for at least

3 seconds.

Adding laundry when Child Lock is on

•To add laundry, deactivate the Child Lock function. To deactivate the Child Lock function, press and hold the Spin and Soil Level buttons simultaneously for at least 3 seconds. See “Pause Option” on page 23 for additional details.

Deactivating the Child Lock function

Press and hold both the Spin and Soil Level buttons simultaneously for approximately 3 seconds.

•When you deactivate the Child Lock function, the “Child Lock [ ]” is turned off.

•The Child Lock function prevents children or the infirm from accidently operating the washer and injuring themselves.

• If a child enters the washing machine, the child may become trapped and suffocate.

WARNING

•Once you have activated the Child Lock function, it continues working even if the power

is turned off.

CAUTION • Forcing the lid open can result in injury or damage to the product.

To add laundry after you have activated the Child Lock function, you must first deactivate the Child Lock function.

English - 20

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 20		2015/12/22 15:10:12

Sound

The Sound Off function can be selected during all cycles.

Garment

You can add or take out laundry items even after the wash has started, as long as the “Garment” light is on. Pushing the Start/Pause button unlocks the lid. If you open the lid and want to continue the wash cycle, close the lid, and then press the Start/Pause button.

If you have activated the Child Lock, you must deactivate it first. See page 20.

Delay End

You can set the washing machine to start your wash automatically at a later time, by choosing a delay time.

The hour displayed indicates the time at which the wash will be ended.

1.Set your wash cycle.

2.Press the Delay End button repeatedly until the delay time is set.

3.Press the Start/Pause button. The “Delay End” indicator will be lit, and the clock will begin counting down until it reaches the set time.

4.To cancel a Delay End function, press the Power button and then turn the washing machine on again.

Pre Soak

Use this function when the laundry is heavily contaminated or stained. This function improves the wash performance by adding a Pre Soak cycle.

-If you select this function, the total cycle time is increased by 15 minutes.

-When the Pre Soak cycle starts, the washing machine repeats a wash cycle after supplying water and then performs a 15-minute soak cycle.

-When the Pre Soak cycle is complete, the configured wash cycle starts without draining water.

AquaJetTM

With a strong spray and soapy water recirculated by the AquaJet™ pump, laundry can be more gently and thoroughly cleaned than in conventional Top Loads.

- AquaJet™ Deep Clean: If AquaJet™ Deep Clean mode is selected, washing performance can be further improved by the additional spray action. Sufficient water quantity can be ensured

by adjusting the water level.

	Cycles	AquaJetTM Function
	NORMAL, HEAVY DUTY, PERM PRESS,	Available
	COLORS/DARKS, ACTIVE WEAR, RINSE+SPIN
	BEDDING, DELICATES,WATERPROOF,	Not Available
	QUICK WASH, SPIN

English - 21

laundry of load a washing 03

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 21		2015/12/22 15:10:12

washing a load of laundry

Mist Shower

Mist Shower sprays water from a nozzle that is independent of the main water supply system. This soaks the laundry with water from the beginning of the rinse cycle and ensures an effective wash even with a small amount of water.

(The Mist Shower function may not work if there is too large of a load in the machine.)

blue round object located left to detergent dispenser

Smart Care (WA48H7400A*, WA45H7200A*)

This function enables you to check the status of the washing machine using a smartphone.

1.To enable the Smart Care function, press and hold the Pre Soak key for 3 seconds after turning the power on or when an error occurs.

•The error code history is deleted after you use this function.

2.The Smart Care indicator is lit on the display.

3.Run the Smart Care app on your smart phone.

•GalaxyS, GalaxyS2, GalaxyS3, GalaxyS4, GalaxyS2(HD), Galaxy Note, Galaxy Note2,

Galaxy Note3 (Other devices may not be normal operation). Supported operating system: Android 2.2 or higher.

• IPhone 3 G S, iPhone 4/4S, iPhone 5/5S. Supported operating system : OS 4.3 or higher.

4.Focus your smart phone’s camera on the display panel of the washing machine.

5.If the smart phone’s camera is focused on the display panel of the washing machine, the panel and error message is automatically recognized and the error type and countermeasures are displayed on the smart phone.

6.If the smartphone fails to recognize the error code more than twice, please enter the error code displayed on the display panel of the washer manually into the Smart Care app.

Downloading the Smart Care app

•Download the Samsung Laundry App into your mobile phone from the Android market or Apple App store. (Search word : Samsung Smart Washer/Dryer)

Precautions when using Smart Care

•If light from a light bulb, fluorescent bulb, or lamp is reflected on the display panel of the washing machine, the smartphone may not be able to recognize the panel or error message easily.

•If you hold the smartphone at too large an angle relative to the front of the display panel, it may not be able to recognize the error code. For best results, hold the smartphone so that the front of the panel and the smartphone are parallel or nearly parallel.

English - 22

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 22		2015/12/22 15:10:12

Washing clothes using the cycle selector

Your new washing machine makes washing clothes easy, using Samsung’s “Fuzzy Control” automatic control system. When you select a wash program, the machine will set the correct temperature, washing time, and washing speed.

1.	Press the Power button.	03
2.	Open the lid.
		washing
3.	compartments. See pages 24~26.
	Load the articles of clothing one at a time loosely into the drum, without overfilling it.
4.	Add liquid (or powder) detergent, softener, and/or bleach (if necessary) to the appropriate
5.	Close the lid.	a
6.	Use the Cycle Selector to select the appropriate cycle according to the type of material:	load
	NORMAL, HEAVY DUTY, COLORS/DARKS, BEDDING, DELICATES, WATERPROOF, PERM	of
	PRESS, ACTIVE WEAR, QUICK WASH, SPIN, RINSE+SPIN. The relevant indicators will
		laundry
	speed, and the delay time by pressing the appropriate option button.
7.	illuminate on the control panel.
	At this time, you can control the wash temperature, the number of rinse cycles, the spinning
8.	Press the Start/Pause button on the Cycle Selector and the wash will begin. The process
	indicator will light up and the remaining time for the cycle will appear in the display.

Pause Option

To remove or add laundry items, follow these steps: 1. Press the Start/Pause button to unlock the lid.

The lid cannot be opened when the water is too HOT.

2.Remove or add laundry items.

3.Close the lid, and then press the Start/Pause button to restart the wash.

If you have Child Lock on, you must deactivate it first. See page 20.

When the cycle is finished:

After the total cycle has finished, the power will turn off automatically.

1.Open the lid.

2.Remove laundry.

ATC (Auto Temperature Control)

ATC is the control function that the washer controls water temperature with temperature sensor (thermistor).

Because there are numerous water temperatures depending on the customer’s environments (cold areas, warm areas, various water temperatures, settings of heater temperature, etcs.), ATC function in our washer maintains the certain level of wash temperature to output the best washing performance at each cycle.

If you select normal & heavy duty cycles, those cycles are the regulation and UL cycle. Since new washer must reduce the amount of energy usage at first priority, customer will notice more cold water entering the washer. But This is Normal, not a problem.

In those regulation cycles, Hot temperature is similar to acceptable adult bath-water temperature and warm temperature is similar to comfortable swimming-pool water temperature.

If customers want to wash clothes in specific water temperature, customers should choose a different cycle at each temperature (Hot/Warm/Eco Warm)

English - 23

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 23		2015/12/22 15:10:12

Liquid detergent compartment

washing a load of laundry

Detergent use

Your washer is designed to use high efficiency (HE) detergents.

•For best cleaning results, use high efficiency detergent such as Tide HE, Wisk HE, Cheer HE or Gain HE*. High efficiency detergents

contain suds suppressors that reduce or eliminate suds. When fewer suds are produced, the load tumbles more efficiently and cleaning is maximized.

WARNING Regular detergent is not recommended. Use HE detergents only.

Reducing the amount of detergent may reduce the quality of cleaning. It is important to pre–treat stains, sort carefully by color and soil level, and avoid overloading.

*Brand names are trademarks of their respective manufacturers.

Features

Automatic dispenser

Your washer has separate compartments for dispensing detergent and color-safe bleach and fabric softener. Add all laundry additives to their respective compartments before starting your Washer.

The automatic dispenser MUST ALWAYS be in place before you start your washer. DO NOT open the automatic dispenser when your washer is running.

•Never exceed the manufacturer’s recommendations when adding detergent.

•This compartment holds liquid detergent for the main wash cycle, which is added to the load at the beginning of the cycle.

•When using powdered detergent, remove the liquid detergent compartment from the detergent drawer. The washer will not dispense powdered detergent from the liquid detergent compartment.

To add detergent to the automatic dispenser:

1. Open the dispenser drawer.

2. Load the recommended amount of liquid (or powder) detergent into the detergent compartment before you start your wash.

3. Close the drawer slowly and smoothly to avoid spilling, splashing, or premature dispensing of the contents.

It is normal for a small amount of water to remain in the dispenser compartments at the end of the cycle.

Do not put chlorine bleach in the dispenser drawer.

English - 24

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 24		2015/12/22 15:10:13

Loading the Liquid (or Powder) detergent compartment

1.Pour the recommended amount of laundry detergent directly into the detergent compartment before starting your washer.

2.If you are using color-safe bleach, add it with the detergent to the detergent compartment.

When adding color-safe bleach with detergent, it is best if both laundry products are in the same form – liquid.

When using powdered detergent, remove the liquid detergent compartment from the detergent drawer. The washer will not dispense powdered detergent from the liquid detergent compartment.

Liquid detergent compartment

Loading the Bleach compartment

(Liquid chlorine bleach only)

1.Add chlorine bleach to the bleach compartment. DO NOT exceed the MAX FILL line.

•Avoid splashing or over–filling the compartment.

•Your washer automatically dispenses bleach into the tub at the appropriate time.

2.The dispenser automatically dilutes liquid chlorine bleach before it reaches the wash load.

•Never pour undiluted liquid chlorine bleach directly onto the load or into the tub. It is a powerful chemical and can cause fabric damage, such as weakening of the fibers or color loss, if not used properly.

Bleach compartment

•If you prefer to use color–safe, non–chlorine bleach, add it to the appropriate detergent compartment.

DO NOT pour color–safe bleach into the Bleach compartment.

English - 25

laundry of load a washing 03

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 25		2015/12/22 15:10:13

washing a load of laundry

Loading the Fabric softener compartment

1.Pour the recommended amount of liquid fabric softener into the softener compartment.

For smaller loads, use less than one capful.

2.Dilute the fabric softener with water until it reaches MAX FILL in the compartment.

3.The dispenser automatically releases liquid fabric softener at the proper time during the rinse cycle.

•Use the softener compartment ONLY for liquid fabric softeners.

•DO NOT use the Downy Ball* in the fabric softener compartment with this washer. It will not add fabric softener at the appropriate time.

Use the detergent compartment.

Fabric softener compartment

•Do not use liquid fabric softener that is too sticky as it may not mix with the water sufficiently.

*Brand names are trademarks of their respective manufacturers.

English - 26

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 26		2015/12/22 15:10:13

maintaining your washer

Cleaning the exterior

Turn off the water faucets after finishing the day’s washing.

This will shut off the water supply to your washer and prevent the unlikely possibility of damage from escaping water. Leave the lid open to allow the inside of your washer to dry out.

Use a soft cloth to wipe up all detergent, bleach or other spills as they occur. Clean the following as recommended:

Control Panel – Clean with a soft, damp cloth. Do not use abrasive powders or cleaning pads. Do not spray cleaners directly on the panel.

Cleaning the interior

Clean the interior of your washer periodically to remove any dirt, soil, odor, mold, mildew, or bacterial residue that may remain in your washer as a result of washing clothes.

Failure to follow these instructions may result in unpleasant conditions, including odors and/or permanent stains on your washer or laundry.

Hard water deposits may be removed, if needed. Use cleaners labeled “Washer safe”.

Storing your washer

Washers can be damaged if water is not removed from hoses and internal components before storage. Prepare your washer for storage as follows:

•Select the Quick Wash cycle and add bleach to the automatic dispenser. Run your washer through the cycle without a load.

•Turn the water faucets off and disconnect the inlet hoses.

•Unplug your washer from the electrical outlet and leave your washer lid open to let air circulate inside the drum.

•If your washer has been stored in below–freezing temperatures, allow time for any leftover water in your washer to thaw out before use.

Preserving the top cover and the front frame

Do not place any heavy or sharp objects or a detergent box on the washing machine. They can scratch or damage the top cover of the unit.

Since the entire washing machine has a high-gloss finish, the surface can be scratched or damaged. Avoid scratching or damaging the surface when using the washing machine.

English - 27

washer your maintaining 04

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 27		2015/12/22 15:10:13

maintaining your washer

Cleaning the dispensers

The automatic dispenser may need to be cleaned periodically due to laundry additive buildup.

1.Pull the dispenser drawer straight back until it stops.

2.Tilt the dispenser drawer upward and remove it.

3. Remove the inserts from the 3 compartments. Rinse the inserts and the drawer with warm water to remove traces of accumulated laundry products.

4.To clean the drawer opening, use a small, non-metal brush to clean the recess. Remove all residue from the upper and lower parts of the recess.

5.Return the inserts to the proper compartments and replace the drawer. By placing the dispenser drawer rail  on

top of the compartment rail  (Tilt the dispenser drawer downward and insert it.), and then push the drawer in firmly and slowly.

English - 28

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 28		2015/12/22 15:10:14

Self Clean

Self Clean is a self-cleaning cycle that removes mold that may	WA48H7400A*
occur inside the washing machine.

1. Press the Power button.

2. Select the Self Clean cycle.

• Once the Self Clean cycle is selected, the only function that can be set is Delay End.

3. Press the Start/Pause button.

•If you press the Start/Pause button, Self Clean

begins.

WA45H7200A*

WA45H7000A*

washer your maintaining 04

•Using Self Clean, you can clean the drum without using a

CAUTION

cleansing agent.

•Never use Self Clean when laundry is in the washing machine. This may cause damage to the laundry or a problem with the washing machine.

The Self Clean Auto Indicator Function

•If the “Self Clean” indicator is lit after a wash, it indicates that tub (drum) cleaning is required. In this case, remove the laundry from the washing machine, turn the power on, and clean the drum by running Self Clean.

•If you do not run Self Clean, the “Self Clean” indicator turns off. However, the “Self Clean” indicator will light again after two washes. Not running Self Clean at this point will not cause a problem with the washing machine.

•Although the Self Clean Auto Indicator appears once a month or so, the frequency may differ depending on the number of times the washing machine is used.

English - 29

WA48H7400A*/WA45H7200A*

WA45H7000A*

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 29		2015/12/22 15:10:15

troubleshooting

Check these solutions if your washer…

PROBLEM	SOLUTION
will not start.	• Make sure the lid is closed.
	• Make sure your washer is plugged in.
	• Make sure the water source faucets are open.
	• Make sure to press the Start/Pause button to start your Washer.
	• Make sure Child Lock is not activated. See page 20.
	• Before your washer starts to fill, it will make a series of clicking noises
	to check the lid lock and do a quick drain.
	• Check the fuse or reset the circuit breaker
has no water or not enough	• Turn both faucets on fully.
water.	• Straighten the water inlet hoses.
	• Disconnect hoses and clean the screens. Hose filter screens may be
	clogged.
has detergent remaining
in the automatic dispenser	• Make sure your washer is running with sufficient water pressure.
after the wash cycle is
complete.
vibrates or is too noisy.	• Make sure your washer is set on a level surface. If the surface is not
	level, adjust your washer’s feet to level the appliance.
	• Make sure your washer is not touching any other object.
	• Make sure the laundry load is balanced.
stops	• Plug the power cord into a live electrical outlet.
	• Check the fuse or reset the circuit breaker.
	• Close the lid and press the Start/Pause button to start your washer.
	For your safety, your washer will not spin unless the lid is closed.
	• Before your washer starts to fill, it will make a series of clicking noises
	to check the lid lock and do a quick drain.
	• There may be a pause or soak period in the cycle. Wait and it may
	start.
	• Check the screens on the inlet hoses at the faucets for obstructions.
	Clean the screens periodically.

English - 30

WA7000HA WASH_WA48H_USER MANUAL_DC68-03133P-11_EN.indd 30		2015/12/22 15:10:15