Operating Manual
FocusPro® TH5320R
Wireless Thermostat |
|
Thermostat Sans Fil |
69-2094EFS-05 |
Termóstato inalámbrico |
Battery Holder
Press down and pull to remove batteries.
Batteries should be replaced once a year (see page 11).
M28430
CAUTION: EQUIPMENT DAMAGE HAZARD. To prevent possible compressor damage, do not operate cooling system when outdoor temperature is below 50°F (10°C).
Need Help?
For assistance with this product please visit http://yourhome.honeywell.com or call Honeywell Customer Care toll-free at 1-800-468-1502
Read and save these instructions.
® U.S. Registered Trademark. Patents pending Copyright © 2012 Honeywell International Inc. All rights reserved.
Français : voir la page 15 • Español: vea la página 30
Contents
About your new thermostat |
|
Initial setup.......................................... |
2 |
Quick reference to controls................. |
3 |
Quick reference to display................... |
4 |
Operation |
|
Fan settings (auto/on)......................... |
5 |
System settings (heat/cool)................. |
6 |
Auto-changeover (heat/cool)............... |
7 |
Remote control.................................... |
8 |
Display outdoor climate....................... |
9 |
Find lost remote control...................... |
9 |
Compressor protection...................... |
10 |
Appendices |
|
Battery replacement.......................... |
11 |
In case of difficulty............................ |
13 |
Limited warranty................................ |
14 |
Regulatory information...................... |
45 |
1 |
69-2094EFS—05 |
Operating Manual
About your new thermostat
Your new wireless thermostat is pre-set for immediate use. All you have to do is choose the settings you prefer:
1. |
Select fan setting (Auto/On)................................................. |
See page 5 |
2. |
Select system setting (Heat/Cool)........................................ |
See page 6 |
69-2094EFS—05 |
2 |
FocusPro® TH5320R Wireless Thermostat
Quick reference to controls
Digital display (see page 4)
Battery holder (see page 11)
Temperature buttons
Press to adjust temperature
M28431
Function buttons
Press to select the function displayed just above each button. (Functions change depending on the task.)
3 |
69-2094EFS—05 |
Operating Manual
Quick reference to display screen
Current inside temperature
Indoor |
Replace Battery |
75 |
Aux |
|
Heat On |
Fan |
System |
Auto |
Heat |
Low battery warnings (see pages 11-12)
Heat |
Temperature setting |
|
|
||
Setting |
|
|
75 |
Auxillary heat |
|
(Only for heat pumps |
||
|
with auxillary heat) |
|
More |
System status |
|
Heat On/Cool On |
||
|
||
|
(If flashing, see page 10) |
|
M28432 |
|
Fan Setting |
System setting |
More |
Auto/On |
Heat/Cool/Auto/Off/Em |
Press to view outdoor climate (if outdoor |
(see page 5) |
Heat (see page 6) |
sensor is installed), or to find a misplaced |
|
|
remote control if installed (see page 9) |
69-2094EFS—05 |
4 |
FocusPro® TH5320R Wireless Thermostat
Select the fan setting
Fan |
System |
More |
Auto |
Heat |
|
|
|
M28433 |
Fan |
System |
More |
On |
Heat |
|
Press FAN to select Auto or On.
In “Auto” mode (the most commonly used setting), the fan runs only when the heating or cooling system is on.
If set to “On,” the fan runs continuously.
M28434
Note: Options may vary depending on your heating/ cooling equipment.
5 |
69-2094EFS—05 |
Operating Manual
Select the system setting
Fan |
System |
More |
Auto |
Heat |
|
M28435
Fan |
System |
More |
Auto |
|
|
|
Cool |
|
|
|
M28436 |
Note: Options may vary depending on your heating/ cooling equipment.
Press SYSTEM to select:
•Heat: Thermostat controls only the heating system.
•Cool: Thermostat controls only the cooling system.
•Off: All systems are off.
•Auto: Thermostat automatically selects heating or cooling depending on the indoor temperature.
•Em Heat (only for heat pumps with auxiliary heat): Thermostat controls Emergency and Auxiliary Heat.
Compressor is locked out.
69-2094EFS—05 |
6 |
FocusPro® TH5320R Wireless Thermostat
Auto Changeover (heat/cool)
Fan |
System |
More |
Auto |
|
|
|
Auto |
|
MCR28437
Press until screen displays “Auto”
Note: The Auto system setting may not appear, depending on how your thermostat was installed.
Auto changeover is a feature used in climates where both air conditioning and heating are often used on the same day. When the system is set to Auto, the thermostat automatically selects heating or cooling depending on the indoor temperature.
Heat and cool settings must be at least 3 degrees apart. The thermostat will automatically adjust settings to maintain this 3 degree separation.
7 |
69-2094EFS—05 |
Operating Manual
Remote Control
Temperature is measured at location of remote control
The optional remote control can act as a mobile thermostat, to maintain a comfortable temperature as you move from room to room.
72 |
Remote |
75 |
has Control |
||
|
Reading |
|
at Thermostat |
|
at Remote |
Fan |
|
More |
Auto |
|
|
|
Cancel |
|
|
|
MCR28438 |
When the system is responding to temperatures measured at the Remote, the thermostat will display “Remote has Control.”
Press CANCEL to restore temperature control to the thermostat (the system will only respond to temperatures measured at the thermostat).
Note: The thermostat may take up to 15 seconds to respond to commands entered at the remote control. See Remote Control Operating Manual for more information.
69-2094EFS—05 |
8 |
FocusPro® TH5320R Wireless Thermostat
Additional Features
Fan |
System |
More |
Auto |
Heat |
|
Press to diplay more options.
Outdoor |
Outdoor |
MCR28439 |
temperature |
humidity |
|
Outdoor |
Outdoor |
|
85 |
50% |
|
|
Humidity |
|
Find Remote
Done
To display outdoor climate
If you have an outdoor air sensor, press MORE to display the current outdoor temperature and humidity. Press DONE to exit.
To find a lost remote control
If you misplace a remote control, press MORE, then FIND REMOTE. The remote will
beep for two minutes to help you locate it. Press anywhere on the display screen to stop the beeping.
Press to find a lost |
|
|
remote control. |
9 |
69-2094EFS—05 |
MCR28440 |
Operating Manual
Built-in compressor protection
This feature helps prevent damage to the compressor in your air conditioning or heat pump system. Damage can occur if the compressor is re-started too soon after shutdown. This feature forces the compressor to wait a few minutes before re-starting.
During the wait time, the display will flash the message Cool On (or Heat On if you have a heat pump).
69-2094EFS—05 |
10 |
FocusPro® TH5320R Wireless Thermostat
Battery replacement (thermostat)
Press down and pull to remove.
M28441
Insert fresh AA alkaline batteries, then reinstall battery holder.
Install fresh batteries when the REPLACE BATTERY warning begins flashing. The warning
flashes about two months before the batteries are depleted.
Remove the battery holder and install 2 fresh AA alkaline batteries.
After batteries are installed, the thermostat will automatically restore communication with the wireless network within a few minutes.
Note: If batteries are inserted within 2 minutes, the time and day will not have to be reset. All other settings are retained in memory.
MCR28442 |
11 |
69-2094EFS—05 |
|
Operating Manual
Battery replacement (outdoor air sensor)
Remove sensor from bracket
M28443
Remove cover and install 2 fresh AA lithium batteries
Replace outdoor air sensor batteries when the REPLACE BATTERY OUTDOOR warning
begins flashing on the the thermostat. The warning flashes about two months before the batteries are depleted.
Remove the sensor from the bracket, remove the cover and install 2 fresh AA lithium batteries.
After batteries are installed, the sensor will automatically restore communication with the wireless network within a few minutes.
69-2094EFS—05 |
MCR28444 |
12 |
|
FocusPro® TH5320R Wireless Thermostat
In case of difficulty
Heating or cooling system does not respond
Screen displays “No Signal”
•Check circuit breaker and reset if necessary.
•Make sure power switch at heating & cooling system is on.
•Make sure furnace door is closed securely.
•Wait 5 minutes for the system to respond.
Thermostat has lost radio contact with the wireless network (usually because of a power outage). To restore power:
•Check circuit breaker and reset if necessary.
•Make sure power switch at heating & cooling system is on.
•Make sure furnace door is closed securely.
After power is restored, the thermostat will automatically restore wireless communication within a few minutes.
13 |
69-2094EFS—05 |
Operating Manual
Up to 5-year limited warranty
Honeywell warrants this product, excluding battery, to be free from defects in the workmanship or materials, under normal use and service, for a period of three (3) years from the date of purchase by the consumer. If at any time during the warranty period the product is determined to be defective or malfunctions, Honeywell shall repair or replace it (at Honeywell’s option).
If the product is defective,
(i)return it, with a bill of sale or other dated proof of purchase, to the place from which you purchased it; or
(ii)call Honeywell Customer Care at 1-800-468-1502.
Customer Care will make the determination whether the product should be returned to the following address:
Honeywell Return Goods, Dock 4 MN10-3860, 1885 Douglas Dr. N., Golden Valley, MN 55422, or whether a replacement product can be sent to you.
This warranty does not cover removal or reinstallation costs.
This warranty shall not apply if it is shown by Honeywell that the defect or malfunction was caused by damage which occurred while the product was in the possession of a consumer.
Honeywell’s sole responsibility shall be to repair or replace the product within the terms stated above. HONEYWELL SHALL NOT BE LIABLE FOR ANY LOSS OR DAMAGE OF ANY
KIND, INCLUDING ANY INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING, DIRECTLY OR INDIRECTLY, FROM ANY BREACH OF ANY WARRANTY, EXPRESS OR IMPLIED, OR ANY OTHER FAILURE OF THIS PRODUCT.
Some states do not allow the exclusion or limitation of incidental or consequential damages, so this limitation may not apply to you.
THIS WARRANTY IS THE ONLY EXPRESS WARRANTY HONEYWELL MAKES ON THIS PRODUCT. THE DURATION OF ANY IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, IS HEREBY LIMITED TO THE THREE-YEAR DURATION OF THIS WARRANTY. Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
This warranty gives you specific legal rights, and you may have other rights which vary from state to state.
If you have any questions concerning this warranty, please write Honeywell Customer Relations, 1985 Douglas Dr, Golden Valley, MN 55422 or call 1-800-468-1502. When the product is registered on-line at www.warranty.Honeywell.com, the standard manufacture coverage stated above extends to a period of (5) years.
69-2094EFS—05 |
14 |