DEUTSCH FRANÇAIS ESPAÑOL ITALIANO ENGLISH
OWNER’S MANUAL
AIR CONDITIONER
Please read this manual carefully before operating your set and retain it for future reference.
TYPE : CASSETTE
The equipment complies with requirements of the Technical Regulation, in terms of restrictions for the use of certain dangerous substances in electrical and electronic equipment.
www.lg.com
P/NO : 3828A20394D
MutliType Air Conditioner Ownerʼs Manual
TABLE OF CONTENTS
Safety Precautions................. |
3 |
Operating Instructions........... |
6 |
Maintenance and Service .... |
24 |
FOR YOUR RECORDS
Write the model and serial numbers here:
Model #
Serial #
You can find them on a label on the side of each unit.
Dealer's Name
Date Purchased
νStaple your receipt to this page in the event you need it to prove date of purchase or for warranty issues.
READ THIS MANUAL
Inside you will find many helpful hints on how to use and maintain your air conditioner properly. Just a little preventive care on your part can save you a great deal of time and money over the life of your air conditioner.
You'll find many answers to common problems in the chart of troubleshooting tips. If you review our chart of
Troubleshooting Tips first, you may not need to call for service at all.
PRECAUTION
•Contact the authorized service technician for repair or maintenance of this unit.
•Contact the installer for installation of this unit.
•The air conditioner is not intended for use by young children or invalids without supervision.
•Young children should be supervised to ensure that they do not play with the air conditioner.
•When the power cord is to be replaced, replacement work shall be performed by authorized personnel only using only genuine replacement parts.
•Installation work must be performed in accordance with the National Electric Code by qualified and authorized personnel only.
2 Multi-Type Air Conditioner
Safety Precautions
Safety Precautions
To prevent injury to the user or other people and property damage, the following instructions must be followed.
νIncorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by the following indications.
WARNING |
This symbol indicates the possibility of death or serious injury. |
CAUTION |
This symbol indicates the possibility of injury or damage. |
ν Meanings of symbols used in this manual are as shown below.
Be sure not to do.
Be sure to follow the instruction.
ENGLISH
WARNING
ν Installation
Do not use a defective or underrated circuit breaker. Use this appliance on a dedicated circuit.
•There is risk of fire or electric shock.
Install the panel and the cover of control box securely.
•There is risk of fire or electric shock.
Do not modify or extend the power cable.
•There is risk of fire or electric shock.
For electrical work, contact the dealer, seller, a qualified electrician, or an Authorized Service Center.
•Do not disassemble or repair the product. There is risk of fire or electric shock.
Always ground the product.
•There is risk of fire or electric shock.
Always install a dedicated |
Use the correctly rated |
circuit and breaker. |
breaker or fuse. |
• Improper wiring or installation |
• There is risk of fire or electric |
may cause fire or electric shock |
shock. |
Do not install, remove, or reinstall the unit by yourself (customer).
•There is risk of fire, electric shock, explosion, or injury.
Be cautious when unpacking and installing the product.
•Sharp edges could cause injury.
Be especially careful of the case edges and the fins on the condenser and evaporator.
Owner's Manual 3
Safety Precautions
For installation, always contact the dealer or an Authorized Service Center.
•There is risk of fire, electric shock, explosion, or injury.
Do not install the product on a defective installation stand.
•It may cause injury, accident, or damage to the product.
Be sure the installation area does not deteriorate with age.
•If the base collapses, the air conditioner could fall with it, causing property damage, product failure, and personal injury.
ν Operation
Do not let the air conditioner run for a |
Take care to ensure that power |
long time when the humidity is very high |
cable could not be pulled out or |
and a door or a window is left open. |
damaged during operation. |
• Moisture may condense and wet |
• There is risk of fire or electric |
or damage furniture. |
shock. |
Do not plug or unplug the |
Do not touch(operate) the |
power supply plug during |
product with wet hands. |
operation. |
|
• There is risk of fire or electric |
• There is risk of fire or electrical |
shock. |
shock. |
Do not place anything on the power cable.
•There is risk of fire or electric shock.
Do not place a heater or other appliances near the power cable.
•There is risk of fire and electric shock.
Do not allow water to run into electric parts.
•It may cause There is risk of fire, failure of the product, or electric shock.
When flammable gas leaks, turn off the gas and open a window for ventilation before turn the product on.
•Do not use the telephone or turn switches on or off.
There is risk of explosion or fire
Do not open the inlet grill of the product during operation.
(Do not touch the electrostatic filter, if the unit is so equipped.)
•There is risk of physical injury, electric shock, or product failure.
Do not store or use flammable gas or combustibles near the product.
•There is risk of fire or failure of product.
If strange sounds, or small or smoke comes from product. Turn the breaker off or disconnect the power supply cable.
•There is risk of electric shock or fire.
When the product is soaked (flooded or submerged), contact an Authorized Service Center.
•There is risk of fire or electric shock.
Do not use the product in a tightly closed space for a long time.
• Oxygen deficiency could occur.
Stop operation and close the window in storm or hurricane. If possible, remove the product from the window before the hurricane arrives.
•There is risk of property damage, failure of product, or electric shock.
Be cautious that water could not enter the product.
•There is risk of fire, electric shock, or product damage.
Ventilate the product from time to time when operating it together with a stove, etc.
• There is risk of fire or electric shock.
When the product is not be used for a long time, disconnect the power supply plug or turn off the breaker.
•There is risk of product damage or failure, or unintended operation.
Turn the main power off when cleaning or maintaining the product.
• There is risk of electric shock.
Take care to ensure that nobody could step on or fall onto the outdoor unit.
•This could result in personal injury and product damage.
4 Multi-Type Air Conditioner
Safety Precautions
CAUTION
ν Installation
Always check for gas |
Install the drain hose to |
(refrigerant) leakage after |
ensure that water is drained |
installation or repair of product. |
away properly. |
• Low refrigerant levels may cause |
• A bad connection may cause |
failure of product. |
water leakage. |
Do not install the product where the |
Use two or more people to |
noise or hot air from the outdoor unit |
lift and transport the |
could damage the neighborhoods. |
product. |
• It may cause a problem for your |
• Avoid personal injury. |
neighbors. |
|
Keep level even when installing the product.
•To avoid vibration or water leakage.
Do not install the product where it will be exposed to sea wind (salt spray) directly.
•It may cause corrosion on the product. Corrosion, particularly on the condenser and evaporator fins, could cause product malfunction or inefficient operation.
ν Operation
Do not expose the skin directly to cool air for |
Do not use the product for special purposes, such as |
long periods of time. |
preserving foods, works of art, etc. It is a consumer air |
(Don't sit in the draft.) |
conditioner, not a precision refrigeration system. |
• This could harm to your health. |
• There is risk of damage or loss of property. |
Do not block the inlet or outlet of air flow.
• It may cause product failure.
Use a soft cloth to clean. Do not use harsh detergents, solvents, etc.
•There is risk of fire, electric shock, or damage to the plastic parts of the product.
Do not touch the metal parts of the product when removing the air filter. They are very sharp!
• There is risk of personal injury.
Do not step on or put anyting on the product. (outdoor units)
•There is risk of personal injury and failure of product.
Always insert the filter securely. Clean the filter every two weeks or more often if necessary.
•A dirty filter reduces the efficiency of the air conditioner and could cause product malfunction or damage.
Do not insert hands or other objects through the air inlet or outlet while the product is operated.
•There are sharp and moving parts that could cause personal injury.
Do not drink the water |
Use a firm stool or ladder |
drained from the product. |
when cleaning or |
|
maintaining the product. |
• It is not sanitary and could cause |
• Be careful and avoid personal |
serious health issues. |
injury. |
Replace the all batteries in the remote control with new ones of the same type. Do not mix old and new batteries or different types of batteries.
• There is risk of fire or explosion
Do not recharge or disassemble the batteries. |
If the liquid from the batteries gets onto your |
Do not dispose of batteries in a fire. |
skin or clothes, wash it well with clean water. Do |
|
not use the remote if the batteries have leaked. |
• They may burn or explode. |
• The chemicals in batteries could cause burns or other |
|
health hazards. |
ENGLISH
Owner's Manual 5
Operating Instructions
Operating Instructions
Indoor Unit
Signal Receiver
Receives the signals from the remote control.
(Signal receiving sound: two short beeps or one long beep.)
Cassette Type Indoor Unit
On/Off |
: Lights up during the system operation. |
Filter Sign |
: Lights up after 2400 hours from the time of first operating unit. |
Timer |
: Lights up during Timer operation. |
Defrost Mode : Lights up during Defrost Mode or Hot Start operation.
Forced |
: Operation procedures when the remote control |
Operation |
can't be used. |
Outdoor Unit |
: Lights up during outdoor unit operation. |
Operation |
(Cooling model only) |
Heat Pump Model
-bacteria
Signal Receptor
Air
Intake |
Cooling Model |
|
Air Outlet |
|
|
|
Remote |
|
|
Controller |
|
|
|
Signal Receptor |
|
Cover |
Cover |
Heat Pump Model |
|
|
display |
|
|
Signal Receiver |
|
|
Cooling Model |
|
Anti-bacteria |
|
|
|
|
Air Outlet |
Air Intake |
Signal Receiver |
|
Remote Controller |
6 Multi-Type Air Conditioner
Operating Instructions
Name and Function of Remote Controller
CST Type Remote Controller
1Way |
AUTO SWING |
OPERATION |
Room Temp |
FAN SPEED |
SUB FUNCTION |
|
|
|
||
|
SET TEMP |
1 |
|
Heat Pump Model |
||||||
|
|
|
|
MED |
JET |
Defrost Humidify |
|
|||
|
|
|
|
HI |
AUTO |
Heater Preheat |
|
|
|
|
|
|
|
|
LO |
|
Filter |
Out door |
|
|
|
|
|
|
Time |
|
|
|
|
|
|
|
|
Timer Operation unit |
Program set |
|
|
|
|
|
|
|
|
|
On Off |
|
|
|
|
|
|
|
|
|
|
Set no. Time 01 |
03 05 07 |
09 11 13 |
15 |
17 19 |
21 |
23 |
|
|
|
|
3 |
|
|
|
|
|
|
|
|
|
4Way,1Way(06 Model) |
17 |
|
|
|
|
|
|
2 |
6 |
|
|
|
|
|
|
|
|
|
Cooling Model |
||
|
|
|
|
|
|
|
|
|
|
10 |
Timer |
Cancel |
|
5 |
|
11 |
|
|
|||
|
|
|
|
||
12 |
Program |
Week |
Holiday |
4 |
|
13 |
|||||
|
|
Plasma |
|||
14 |
|
|
Set/Clr |
7 |
|
15 |
Hour |
Min |
RESET |
8 |
|
|
|||||
16 |
|
|
|
9 |
18
1Operation Display
Displays the operation conditions.
2On/Off Button
Operation starts when this button is pressed, and stops when the button is pressed again.
3Set Temperature Button
Used to set the temperature when the desired temperature is obtained.
4FAN Operation Button
Used to circulate room air without cooling or heating.
5Fan Speed (Jet Cool Button: 4 Way)
Used to set the desired fan speed or select Jet cool mode.
6Operation Mode Selection Button
Used to select the operation mode.
•Auto Operation Mode
•Cooling Operation Mode
•Soft Dry Operation Mode
•Heating Operation Mode(except cooling model)
7Auto Swing Button
Used To Swing Up And Down/ Right And Left(Option)
8Room Temperature Checking Button/Filtersign Release(Option)
Used to check the room temperature.
9 Plasma Air Clean Button(Option)/Heater(Option)
10Timer Cancel Button
Used to cancel the timer.
11Timer Set Button
Used to set the timer when the desired time is obtained.
12Week Button
Used to set a day of the week.
13Program Button
Used to set the weekly timer.
14Holiday Button
Used to set a holiday of the week.
15Time Set Button
Used to set the time of the day and change the time in the weekly timer Function.
16Set And Clean/Ventilation(Option)
Used to set and clear the weekly timer.
17Swirl Button (4 Way)
Used to select swirl mode.
No Function(1 Way 06 Model) Jet Cool Button(1 Way)
18Reset Button
Used to set the current time and clear the setting time.
ηDisplay temperature can be different from actual room temperature if the remote controller is installed at the place where sun-rays are falling directly or the place nearby heat source.
ηNote : 1 Way '06 Model - AMNH09GTCC0, AMNH12GTCC0
ENGLISH
Owner's Manual 7
Operating Instructions
Wireless Remote Controller (optional)
This air-conditioner is equipped with wired remote controller basically. But if you want to be available with wireless remote controller, you pay for it.
Signal transmitter
5 |
1 |
|
6 |
|
|
|
3 |
|
4 |
10 |
|
2 |
||
CANCEL |
||
7 |
9 |
|
ON |
OFF SET |
|
11 |
12 |
|
8 |
||
|
||
13 |
|
14 |
15 |
|
|
|
Flip-up door |
|
(opened) |
1.START/STOP BUTTON
Operation starts when this button is pressed and stops when the button is pressed again.
2.OPERATION MODE SELECTION BUTTON
Used to select the operation mode.
3.ROOM TEMPERATURE SETTING BUTTONS
Used to select the room temperature.
4.INDOOR FAN SPEED SELECTOR
Used to select fan speed in four steps low, medium, high and CHAOS.
5.JET COOL
Used to start or stop the speed cooling/heating. (Speed cooling/heating operates super high fan speed.)
6.CHAOS SWING BUTTON
Used to stop or start louver movement and set the desired up/down airflow direction.
7.ON/OFF TIMER BUTTONS
Used to set the time of starting and stopping operation.
8.TIME SETTING BUTTONS
Used to adjust the time.
9.TIMER SET/CANCEL BUTTON
Used to set the timer when the desired time is obtained and to cancel the Timer operation.
10.SLEEP MODE AUTO BUTTON
Used to set Sleep Mode Auto operation.
11.AIR CIRCULATION BUTTON
Used to circulate the room air without cooling or heating.
12.ROOM TEMPERATURE CHECKING BUTTON
Used to check the room temperature.
13.PLASMA(OPTIONAL)
Used to start or stop the plasma-purification function.
14.RESET BUTTON
Initialize remote controller.
15.2nd F Button
Used prior to using modes printed in blue at the bottom of buttons.
ηThe wireless remote controller do not operate the swirl mode.
CAUTION:of handling the Remote Controller
•Aim at the signal receiver on the wired remote controller so as to operate.
•The remote control signal can be received at a distance of up to about 7m.
•Be sure that there are no obstructions between the remote controller and the signal receptor.
•Do not drop or throw the remote controller.
•Do not place the remote controller in a location exposed to direct sunlight, or near the heating unit, or any other heat source.
•Block a strong light over the signal receptor with a curtain or etc. so as to prevent the abnormal operation. (ex:electronic quick start, ELBA, inverter type fluorescent lamp)
8 Multi-Type Air Conditioner
Operating Instructions
Set the Current Time and day of the Week
Unless you press any button about 5 (sometimes 10) seconds while setting function, the setting mode returns to initial mode.
1 |
Press the ' |
' button. |
|
|
|
|
|
|
|
|||
|
Hour |
|
|
|
|
|
|
|
||||
Each time the button is pressed, the number is changed from to 23. |
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|||||
|
This number indicates current hour. |
SET TEMP |
|
FAN SPEED |
|
SUB FUNCTION |
||||||
|
|
|
|
|
OPERATION |
|
|
|||||
|
|
|
|
|
|
Time |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For example, if it is 14:25, press Hour button 14 times. |
|
|
|
|
|
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
2 |
Press the ' |
' button. |
|
|
|
|
|
|
|
|||
|
Min |
|
|
|
|
|
|
|
||||
Each time the button is pressed, the number increases from 00 to 59. |
|
|
|
|
|
|
||||||
|
|
|
|
|
|
|
||||||
|
This number indicates current minute. |
SET TEMP |
|
FAN SPEED |
|
SUB FUNCTION |
||||||
|
|
|
|
|
OPERATION |
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
For example, if it is 14:25, press Min button 25 times.
Week
3Press ' ' button.
Each time the button is pressed, a day of the week is shifted from sunday to saturday.
OPERATION SET TEMP FAN SPEED SUB FUNCTION
Week
Time
Week
For example, if today is Wed, press button 3 times.
4Press the ' RESET ' button.
If you want to confirm the current time and a day of the week, click the Reset button.
RESET |
OPERATION SET TEMP FAN SPEED SUB FUNCTION |
|
ENGLISH
Owner's Manual 9