LG LW8016HR/00 Owner’s Manual

OWNER’S MANUAL

AIR CONDITIONER

DANSK SUOMI NORSK

Please read this manual carefully before operating your set and retain it for future reference.

TYPE : WINDOW

MODELS LW8016HR

P/NO : MFL69392001

www.lg.com

Safety Precautions
Before Operation	7
Introduction
Electrical Safety
Installation
Operating Instructions	16
Maintenance and Service	20

Do not store flammables like

gasoline benzene thinner etc. near the air conditioner

No correlation between fan	Unplug the unit when not
usage and oxygen depletion.	using it for a long time.

Hold the plug by the head	When gas leaks, open the
not the cable when taking	window for ventilation before
it out.	operating the unit.

Never touch the metal parts of the unit when removing the filter.

For inner cleaning, contact an Authorized Service Center or a dealer.

Do not use harsh detergent that causes corrosion or damage on the unit. Harsh detergent may also cause failure of product, fire, or electric shock.

Install the product so the exhaust and noise Follow installation instructions exactly. are not aimed directly at the neighbors.

Be considerate.

Do not use this appliance for special purposes such as cooling pets foods precision machinery or objects of art

Instead of running air conditioning constantly,open a window

for fresh air occasionally.

You will feel better.

If the liquid from the battery gets onto your skin or clothers wash it well with clean water. Do

not use the remote if the battery has leaked.

y

If you eat the liquid from the battery,brush your teeth and see doctor.Do not use the

remote if the battery has leaked.

y

2.No correlation between fan usage and oxygen depletion.

3.

Introduction

Introduction

SymbolsUsedinthisManual

This symbol alerts you to the risk of electric shock.

This symbol alerts you to hazards that could cause harm to the air conditioner.

NOTICE This symbol indicates special notes.

Features

This appliance should be installed in accordance with the National Electric Code.

		Vertical Air Deflector
		(Horizontal Louver)
			Horizontal Air Deflector
			(Vertical Louver)
			Air Discharge
	Cabinet	Air Intake (Inlet Grille)
	Front Grille	Air Filter	Remote Controller
		Brace
			Condenser
			Base Pan
	Electric Heater		Compressor
		Power Cord
		Control Board
		Evaporator

8 Room Air Conditioner

RESET

TEST

USE OF EXTENSION CORDS

RISK OF FIRE could cause serious injury or death DO NOT use an extension cord with this window air conditioner

DO NOT use surge protectors or multi-outlet adapters with this window air conditioner

should be

Avoid shock hazard. This unit cannot be user-serviced. Do NOT open the tamper-resistant sealed portion.

All warranties and performance will be voided. This unit is not intended to be used as an ON/OFF switch.

13 EA	3 EA	5 EA	2 EA
2 EA	2 EA		2 EA
		Left Guide Panel	Right Guide Panel
(Not adhesive backed)	1 EA
1 EA
			Curtain
2 EA	1 EA	( Adhesive backed)
		1EA

Phillips head screwdriver

Scissors or knife

Adjustable

Wrench

Owner’s Manual 11

HowtoInstalltheUnit

1. To prevent vibration and noise, make sure the unit

	is installed securely and firmly	Fence
		Awning

2.Install the unit where the sunlight does not shine directly on the unit.

3.The outside of the cabinet must extend outward for at least 11" and there should be no obstacles, such as a fence or wall, within 20" from the back of the cabinet because it will prevent heat radiation of the condenser.

Restriction of outside air will greatly reduce the cooling efficiency of the air conditioner.

Cooled air

30"~60"

Heat radiation

About 1/2"

Over 20"

All side louvers of the cabinet must remain exposed to the outside of the structure.

4.Install the unit slightly tilted so the back is slightly lower than the front (about1/2"). This will force condensed water to flow to the outside.

5.Install the unit with the bottom between 30"~60" above the floor level.

NOTICE

All supporting parts should be secured to firm wood, masonry, or metal.

This unit is designed for installation in standard double hung windows with actual opening widths from 22" to 36".

The top and bottom window sash must open sufficiently to allow a clear vertical opening of 14" from the bottom of the upper sash to the window stool.

22 36

14

Preparation Of Chassis

Shipping Screws

Remove 4 screws which fasten the cabinet at both sides and at the back. (Keep the screws for later use.)

12

the base pan

(adhesive backed)

Adhesive backed

	Upper guide	Right Guide Panel
	Left Guide panel

8

Screws

(Type A)

Frame guide

hole

upper

Center hole

guide

frame curtain

sill support.

13

frame guides sill support

sill support

frame curtain

frame curtain

(removed from the cabinet) at

See page 12.

Screw

Screw

14

not adhesive backed

Not adhesive backed

Type C

Before installing the front grille, pull out the vent control lever located above the unit control knobs, as shown.

14 slots

Guide the lever carefully through the grille as you push it in.

15 Lift the inlet grille and secure it with a Type

A screw through the front grille.

16

15