LW1016ER/00
OWNER’S MANUAL
AIR
CONDITIONER
Please read this manual carefully before operating
your set and retain it for future reference.
NORSK SUOMI DANSK
TYPE :
MODELS LW1016ER
P/NO : MFL69365403
WINDOW
www.lg.com
Safety Precautions
Before Operation
Introduction
Safety
Installation
Operating Instructions
Maintenance and Service
7
16
20
Do not store flammables like
gasoline benzene thinner
etc. near the air conditioner.
No correlation between fan
usage and oxygen depletion.
Unplug the unit when not
using it for a long time.
Hold the plug by the head
（not the cable）when taking
it out.
For inner cleaning, contact an Authorized Service Center or a dealer.
Do not use harsh detergent that causes corrosion or damage on the unit.
Harsh detergent may also cause failure of prod
When gas leaks, open the
window for ventilation before
operating the unit.
uct, fire, or electric shock.
Never touch the metal parts
of the unit when removing
the filter.
Install the product so the exhaust and noise
are not aimed directly at the neighbors.
Be considerate.
Follow installation instructions exactly.
Do not use this appliance for
special purposes such as
，
cooling pets
foods，
precision
machinery，or objects of art
Instead of running air conditioning
constantly
for fresh air occasionally.
You will feel better.
If the liquid from the battery gets onto your skin
or clothers，
wash it well with clean water. Do
not use the remote if the battery has leaked.
y
，open a window
If you eat the liquid from the battery,brush
your teeth and see doctor.Do not use the
remote if the battery has leaked.
y
2. No correlation between fan usage and oxygen depletion.
3.
RESET
TEST
USE OF EXTENSION CORDS
RISK OF FIRE could cause serious injury or death
DO NOT use an extension cord with this window
air conditioner
DO NOT use surge protectors or multi-outlet
adapters with this window air conditioner
should
be
Avoid shock hazard. This unit cannot
be user-serviced. Do NOT open the
tamper-resistant sealed portion.
All warranties and performance will
be voided. This unit is not intended
to be used as an ON/OFF switch.
WARNING
1.Do not use means to accelerate the defrosting process
or to clean, other than those recommended by the
manufacturer
2.The appliance shall be stored in a room without
continuously operating ignition sources (for example:
open flames, an operating gas appliance or an
operating electric heater)
3.Do not pierce or burn. Be aware that refrigerants may
not contain an odor
This unit contains flammable refrigerant and has
special safety precautions not normally associated
with older units. Please follow all precautions and
advisories.
1. Use caution while handling and prevent damage
to unit.Do not put any holes into product for any
reason, this can cause damage to product and
prevent unit from cooling.
2. Maintenance and cleaning of unit should be
performedby trained personnel. Failure to properly
clean unit can result in damage to the refrigeration
system and or the electrical system.
3. Make certain that all the air circulation/ventilation
openings are free from obstruction.
4. Service should only be performed by technicains
properly trained and certified in the use of flammable
refrigerants. Any service performed by unauthorized
servicers/individuals will void all warranties.
5. When storing the appliance, do not put in a room
with any open flame appliances, such as gas water
heaters or furnaces. Also keep away from electric
heaters. Damaged units should be repaired before
storage.
14 EA
3 EA 5 EA
2 EA
2 EA
(Not adhesive backed)
1 EA
2 EA
Phillips head
screwdriver
2 EA
1 EA
1 EA
Left Guide Panel
( Adhesive backed)
EA
2 EA
Right Guide Panel
Curtain
FOAM-HEATPROOF
Scissors or
knife
Adjustable
Wrench
11
slightly tilted
between
Preparation Of Chassis
Remove 4 screws which fasten the cabinet at both
sides and at the back.
(Keep the screws for later use.)
27 39
16
12
(Adhesive backed)
and bottom of window frame.
the base pan
（Adhesive backed）
guide
hole
frame curtain
sill support.
Upper guide
Left Guide panel
Right Guide Panel
8
Screws
(Type A)
Frame guide
upper
Center hole
13
frame guides
sill support
frame curtain
frame curtain
sill support
14
(removed from the cabinet) at
See page 12.
（Not adhesive backed）
Foam-Strip
(Not adhesive backed)
Before installing the front grille, pull out
the vent control lever located above the
unit control knobs, as shown.
14
Cut the adhesive-backed FoamHeatproofs to the Guide Panel size.
Remove the backing from the
Foam-Heatproofs and attach
the Foam-Heatproofs to Guide Panel.
Foam-Heatproof improves
the cooling capability of the unit.
15
Attach the front grille to the cabinet by inserting
the tabs the grille into the slots on the front the
cabinet.Push the grille in until it snaps into place.
Guide the lever carefully through the
grille as you push it in.
16
Take out the air filter and secure it with 2 Type
A screws through the front grille.
These 2 Type A screws are
packaged by bag.
Foam-Heatproof
Window installation of room air conditioner is
now completed. See ELECTRICAL DATA for
attaching power cord to electrical outlet.
15
Loading...