<![endif]>ENGLISH
IPS LED MONITOR
Please read this manual carefully before operating your set and retain it for future reference.
IPS LED MONITOR MODEL
22MP55HQ
23MP55HQ
24MP55HQ
27MP55HQ
www.lg.com
<![endif]>ENGLISH
2 TABLE OF CONTENTS
3 |
ASSEMBLING AND PREPAR- |
24 |
TROUBLESHOOTING |
||
|
ING |
|
|
|
|
|
|
|
|
||
3 |
Unpacking |
|
26 |
SPECIFICATIONS |
|
4 |
Parts and buttons |
||||
26 |
22MP55HQ |
||||
5 |
Moving and Lifting the Monitor |
||||
6 |
Setting up the Monitor set |
27 |
23MP55HQ |
||
6 |
- Attaching the Stand Base |
28 |
24MP55HQ |
||
7 |
- Detaching the Stand Base |
29 |
27MP55HQ |
||
8 |
- Mounting on a table |
30 |
Preset Modes (Resolution) |
||
8 |
- Using the cable holder |
30 |
Indicator |
||
10 - Mounting on a wall |
|
31 |
|
||
11 |
USING THE MONITOR SET |
PROPER POSTURE |
|||
31 |
Proper posture for using the Monitor set. |
11Connecting to a PC
11- D-SUB connection
11- HDMI connection
12Connecting to AV Devices
12- HDMI connection
13CUSTOMIZING SETTINGS
14Customizing Settings
14- Menu Settings
15-Picture
16-Color
17-Display
17-Audio
18-Others
19READER Setting
20FUNC. Setting
20-SUPER ENERGY SAVING
21-Picture Mode
22-SUPER RESOLUTION +
23-DUAL DISPLAY
23 -DUAL WEB
ASSEMBLING AND PREPARING 3
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories.
<![endif]>ENGLISH
CD(Owner's Manual) / |
D-SUB Cable |
Card |
(This cable is not included in all |
|
countries.) |
Power Cord |
AC-DC Adapter |
( Depending on the country )
HDMI Cable
(This cable is not included in all countries.)
or
AC-DC Adapter
( Depending on the country )
Stand Body |
Stand Body |
Two Screws |
Stand Base |
(22MP55HQ/ 23MP55HQ |
|
|
|
/24MP55HQ) |
|
|
|
CAUTION
yyDo not use any unapproved accessories to ensure the safety and product life span.
yyAny damages or injuries by using unapproved accessories are not covered by the warranty.
NOTE
yyThe accessories supplied with your product may vary depending on the model.
yyProduct specifications or contents in this manual may be changed without prior notice due to upgrade of product functions.
4 ASSEMBLING AND PREPARING
<![endif]>ENGLISH
Power Indicator yyLightingOn:Turnedon yyLightingOff: Turned off
(Power Button)
READER
Button (See p.13)
Connection panel (See p.11)
|
ASSEMBLING AND PREPARING 5 |
|||
|
|
|
|
|
Moving and Lifting the Monitor |
yyWhen holding the monitor, the screen should |
|||
|
||||
When moving or lifting the monitor, follow these |
face away from you to prevent it being |
|||
instructions to prevent the monitor from being |
scratched. |
|||
scratched or damaged and to ensure safe trans- |
|
|
|
|
portation regardless of its shape or size. |
|
|
|
|
|
|
|
|
|
yyIt is advisable to place the monitor in the |
|
|
|
|
original box or packing material before at- |
|
|
|
|
tempting to move it. |
|
|
|
|
yyBefore moving or lifting the monitor, discon- |
|
|
|
|
nect the power cord and all cables. |
|
|
|
|
yyHold the top and bottom of the monitor frame |
yyWhen moving the monitor, avoid any strong |
|||
firmly. Do not hold the panel itself. |
shock or vibrations to the product. |
|||
|
yyWhen moving the monitor, keep it upright, |
|||
|
never turn the monitor on its side or tilt it |
|||
|
sideways. |
CAUTION
yyAs far as possible, avoid touching the monitor screen. This may result in damage to the screen or some of the pixels used to create images.
<![endif]>ENGLISH
<![endif]>ENGLISH
6 ASSEMBLING AND PREPARING
1Place the Monitor set with the screen side down on a flat and cushioned surface.
CAUTION
Lay a foam mat or soft protective cloth on the surface to protect the screen from damage.
222MP55HQ/ 23MP55HQ /24MP55HQ
1 Attach the Stand Body to the monitor set.
2 Attach the Stand Base.
3 Tighten the screw to the right.
27MP55HQ
1 Attach the Stand Body to the monitor set.
2Use two screws to fix the Stand Body and monitor set.
3 Attach the Stand Base.
4 Tighten the screw to the right .
Stand Body
Stand Body
Stand Body
Stand Base
Stand
|
|
|
ASSEMBLING AND PREPARING 7 |
|
Detaching the Stand Base |
|
|
|
|
27MP55HQ |
|
|||
1 Place the Monitor set with the screen side |
1 |
Turn the screw to the left. |
||
down on a flat and cushioned surface. |
2 |
Pull out the Stand Base from the Stand Body. |
||
|
3 |
Remove two screws and pull out the Stand |
Body from the monitor set.
2 22MP55HQ/ 23MP55HQ /24MP55HQ
1Pull out the Stand Body and Stand Base from the monitor set.
2 Turn the screw to the left.
3 Pull out the Stand Base.
Stand Body
Stand Body
Stand Base
Stand Base
Stand Body
Stand Body
Stand Base
CAUTION
yyThis illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture.
yyDo not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot.
<![endif]>ENGLISH
<![endif]>ENGLISH
8 ASSEMBLING AND PREPARING
1Lift and tilt the Monitor set into its upright position on a table.
Leave a 10 cm (minimum) space from the wall for proper ventilation.
10 cm
10 cm
10 cm
10 cm
3Press (Power) button on the bottom switch panel to turn the power on.
CAUTION
Unplug the power cord before moving the Monitor to another location. Otherwise electric shock may occur.
2Connect the AC-DC Adapter and Power Cord to a wall outlet.
Cable holder
or
ASSEMBLING AND PREPARING 9
WARNING
When you adjust the angle, do not hold the bottom of the Monitor set frame as shown on the following illustration, as may injure your fingers.
27MP55HQ
NOTE
+20 to -5 degrees up or down to adjust the angle of the Monitor set to suit your view.
<![endif]>ENGLISH
Do not touch or press the screen when adjusting the angle of the monitor.
Do not hold this set like below picture.Monitor screen can detach from stand base and injure your body.
22MP55HQ/23MP55HQ/24MP55HQ
NOTE
+20 to -3 degrees up or down to adjust the angle of the Monitor set to suit your view.
Front Rear
Using the Kensington security system
The Kensington security system connector is located at the back of the Monitor set. For more information of installation and using, refer to the manual supplied with the Kensington security system or visit http://www.kensington.com.
Connect the Kensington security system cable between the Monitor set and a table.
NOTE
The Kensington security system is optional. You can obtain it from most electronics stores.
Front Rear
<![endif]>ENGLISH
10 ASSEMBLING AND PREPARING
|
Model |
|
|
|
|
|
|
|
|
22MP55HQ |
|
|
24MP55HQ |
|
|
|
|
|
|
|
|
||
Mounting on a wall |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
23MP55HQ |
|
|
27MP55HQ |
|
|
For proper ventilation, allow a clearance of 10 cm |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
VESA (A x B) |
|
75 x 75 |
100 x 100 |
||||
on each side and from the wall. Detailed |
Standard screw |
|
M4 |
|
|
|
|
instructions are available from your dealer, see the |
Number of screws |
4 |
|
|
|
|
|
optional Tilt Wall Mounting Bracket Installation and |
|
|
|
|
|
|
|
Setup Guide. |
CAUTION |
|
10 cm
10 cm
10 cm
10 cm
If you intend to mount the Monitor set to a wall, attach Wall mounting interface (optional parts) to the back of the set.
When you install the Monitor set using a wall mounting interface (optional parts), attach it carefully so it will not drop.
yyDisconnect the power cord first, and then move or install the Monitor set. Otherwise electric shock may occur.
yyIf you install the Monitor set on a ceiling or slanted wall, it may fall and result in severe injury.
yyUse only an authorized LG wall mount and contact the local dealer or qualified personnel.
yyDo not over tighten the screws as this may cause damage to the Monitor set and void your warranty.
yyUse only screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the warranty.
yyScrew length from outer surface of back cover should be under 8mm.
Wall mount Pad
Back Cover
1 |
Please, Use the screw and wall mount interface |
Wall mount Pad |
|
in accordance with VESA Standards. |
Back Cover |
2 |
If you use screw longer than standard, the |
Standard screw |
|
||
|
monitor might be damaged internally. |
|
3If you use improper screw, the product might be damaged and drop from mounted position. In
this case, LG Electronics is not responsible for it.
4VESA compatible only with respect to screw mounting interface dimensions and mounting
screw specifications.
5 Please use VESA standard as below. yy784.8 mm (30.9 inch) and under
*Wall Mount Pad Thickness : 2.6 mm * Screw : Φ 4.0 mm x Pitch 0.7 mm x Length 10 mm
yy787.4 mm (31.0 inch) and above
*Please use VESA standard wall mount pad and screws.
Max.8mm
NOTE
yyUse the screws that are listed on the VESA standard screw specifications.
yyThe wall mount kit will include an installation manual and necessary parts.
yyThe wall mount bracket is optional. You can obtain additional accessories from your local dealer.
yyThe length of screws may differ depending on the wall mount. Be sure to use the proper length.
yyFor more information, refer to the instructions supplied with the wall mount.