LG 23EN43VQ, 24EN43VQ, 24EN43VQ-B, 23EN43VQ-B, 27EN43VQ-B Manual

...

0 (0)

ENGLISH

OWNER’S MANUAL

LED LCD MONITOR

Please read this manual carefully before operating your set and retain it for future reference.

LED LCD MONITOR MODEL

22EN43VQ 23EN43VQ 24EN43VQ 27EN43VQ

www.lg.com

ENGLISH

ENG

TABLE OF CONTENTS

3 ASSEMBLING AND PREPAR-

ING

3 Unpacking

4 Parts and buttons

5 Setting up the Monitor set

5 - Attaching the Stand Base

6 - Detaching the Stand Base

7 - Mounting on a table

7 - Using the cable holder

9 - Mounting on a wall

10 USING THE MONITOR SET

10 Connecting to a PC

10 - D-SUB connection

10 - DVI-D connection

10 - HDMI connection

12 CUSTOMIZING SETTINGS

13 Customizing Settings

13 - Menu Settings

14 - Picture

15 - Color

16 - Display

16 - Volume

17 - Others

18 MY KEY Setting

19 FUNC. Setting

19 - Picture Mode

20 - SUPER ENERGY SAVING

21 - DUAL DISPLAY

21 - DUAL WEB

22 - MY KEY Setting

23 TROUBLESHOOTING

25 SPECIFICATIONS

25 22EN43VQ

26 23EN43VQ

27 24EN43VQ

28 27EN43VQ

29 Preset Modes (Resolution)

29 HDMI TIMING

29 Indicator

30 PROPER POSTURE

30 Proper posture for using the Monitor set.

ASSEMBLING AND PREPARING

Unpacking

Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories.

CD(Owner's Manual) /

Card

D-SUB Cable

DVI-D Cable

(This cable is not included

in all countries.)

ENGLISH

ENG

Power Cord AC-DC Adapter AC-DC Adapter

( Depending on the country ) ( Depending on the country )

Stand Body

(22EN43VQ/23EN43VQ/

24EN43VQ)

Stand Body

(27EN43VQ)

Two Screws

(27EN43VQ)

Stand Base

CAUTION

Do not use any unapproved accessories to ensure the safety and product life span.

Any damages or injuries by using unapproved accessories are not covered by the warranty.

NOTE

The accessories supplied with your product may vary depending on the model.

Product specifications or contents in this manual may be changed without prior notice due to upgrade

of product functions.

ENGLISH

ENG

ASSEMBLING AND PREPARING

Parts and buttons

Power Indicator

Lighting On: Turned on

Lighting Off: Turned off

(Power Button)

Button (See p.12)

Connection panel (See p.10)

ASSEMBLING AND PREPARING

Setting up the Monitor set

Attaching the Stand Base

Place the Monitor set with the screen side

down on a flat and cushioned surface.

CAUTION

Lay a foam mat or soft protective cloth on the surface to protect the screen from damage.

22EN43VQ/23EN43VQ/24EN43VQ

Attach the Stand Body to the monitor set. Attach the Stand Base.

Tighten the screw to the right with a coin.

27EN43VQ

Attach the Stand Body to the monitor set.

Use two screws to fix the Stand Body and

monitor set.

Attach the Stand Base.

Tighten the screw to the right with a coin.

Stand Body

ENGLISH

ENG

Stand Body

Stand Base

Stand Body

Stand Base

ASSEMBLING AND PREPARING

ENGLISH

ENG

Stand Body

Detaching the Stand Base

Place the Monitor set with the screen side

down on a flat and cushioned surface.

22EN43VQ/23EN43VQ/24EN43VQ

Pull out the Stand Body and Stand Base from the monitor set.

Turn the screw to the left with a coin. Pull out the Stand Base.

27EN43VQ

Turn the screw to the left with a coin.

Pull out the Stand Base from the Stand Body.

Remove two screws and pull out the Stand Body from the monitor set.

Stand Body

Stand Base

Stand Body

Stand Base

CAUTION

This illustration depicts the general model of

connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding

only the stand base. The product may fall and get damaged or injure your foot.

ASSEMBLING AND PREPARING

Mounting on a table

Lift and tilt the Monitor set into its upright

position on a table.

Leave a 10 cm (minimum) space from the wall for proper ventilation.

10 cm

Press (Power) button on the bottom switch

panel to turn the power on.

CAUTION

Unplug the power cord before moving the Monitor to another location. Otherwise electric shock may occur.

Using the cable holder

ENGLISH

ENG

Connect the AC-DC Adapter and Power Cord

to a wall outlet.

Cable holder

ASSEMBLING AND PREPARING

ENGLISH

ENG

WARNING

When you adjust the angle, do not hold the bottom of the Monitor set frame as shown on the following illustration, as may injure your fingers.

Do not touch or press the screen when adjusting the angle of the monitor.

Do not hold this set like below picture.Monitor screen can detach from stand base and injure your body.

Using the Kensington security system

The Kensington security system connector is located at the back of the Monitor set. For more information of installation and using, refer to the manual supplied with the Kensington security system or visit

Connect the Kensington security system cable between the Monitor set and a table.

http://www.kensington.com

NOTE

Tilt from +20 to -5 degrees up or down to adjust the angle of the Monitor set to suit your view.

Front Rear

The Kensington security system is optional. You can obtain it from most electronics stores.

ASSEMBLING AND PREPARING

Mounting on a wall

For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide.

10 cm

If you intend to mount the Monitor set to a wall, attach Wall mounting interface (optional parts) to the back of the set. When you install the Monitor set using a wall mounting interface (optional parts), attach it carefully so it will not drop.

Please, Use the screw and wall mount interface

in accordance with VESA Standards.

If you use screw longer than standard, the

monitor might be damaged internally.

If you use improper screw, the product might be

damaged and drop from mounted position. In this case, LG Electronics is not responsible for it.

VESA compatible.

Please use VESA standard as below.

784.8 mm (30.9 inch) and under

* Wall Mount Pad Thickness : 2.6 mm

* Screw : Φ 4.0 mm x Pitch 0.7 mm x

Length 10 mm

787.4 mm (31.0 inch) and above

* Please use VESA standard wall mount pad

and screws.

10 cm

Model

VESA (A x B) 75 x 75 100 x 100 Standard screw M4 Number of screws 4

22EN43VQ 23EN43VQ

24EN43VQ

27EN43VQ

CAUTION

Disconnect the power cord first, and then

move or install the Monitor set. Otherwise electric shock may occur. If you install the Monitor set on a ceiling or

slanted wall, it may fall and result in severe injury. Use only an authorized LG wall mount

and contact the local dealer or qualified personnel. Do not over tighten the screws as this may

cause damage to the Monitor set and void your warranty. Use only screws and wall mounts that

meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the warranty.

NOTE

Use the screws that are listed on the VESA

standard screw specifications. The wall mount kit will include an installation

manual and necessary parts. The wall mount bracket is optional. You can

obtain additional accessories from your local dealer. The length of screws may differ depending

on the wall mount. Be sure to use the proper length. For more information, refer to the

instructions supplied with the wall mount.

ENGLISH

ENG

USING THE MONITOR SET

ENGLISH

ENG

USING THE MONITOR SET

Connecting to a PC

Your Monitor set supports Plug & Play*.

*Plug & Play: A PC recognizes a connected device that users connect to a PC and turn on, without device configuration or user intervention.

D-SUB connection

Transmits analog video from your PC to the Monitor set. Connect the PC and the Monitor set with the supplied D-sub 15 pin signal cable as shown in the following illustrations.

DVI-D connection

Transmits a digital video signal from your PC to the Monitor set. Connect the PC and the Monitor set with a DVI cable as shown in the following illustrations.

NOTE

When using a D-Sub signal input cable

connector for Macintosh

Mac adapter

For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-SUB VGA connector on the supplied cable to a 15 pin 2 row connector.

HDMI connection

Transmits the digital video and audio signals from your PC or A/V to the Monitor set. Connect the PC or A/V and the Monitor set with the HDMI cable as shown in the following illustrations.

NOTE

If you use HDMI PC, it can cause compatibility

problem.

+ 21 hidden pages