Integra DTR-40.6, DTR-20.9 Owner's Manual

DTR-40.6

Basic Manual

Advanced Manual found here

http://integraworldwide.com/manual/dtr406/adv/en.html

Before Start

About the Basic Manual

The Basic Manual leads you through the fundamental steps to enjoy the AV Receiver from connections to TV, speaker system and playback components, to necessary functions for playback. As well as that, Basic Manual informs you with the instructions on frequently used functions. Besides, there is another part of the manual called Advanced Manual to inform you with more detailed information, which we have decided to publish on the web from the ecological point of view.

Advanced Manual

Advanced Manual is always updated with the latest information and its user friendly interface, which does not matter whether you access from PC or Smartphone, helps you to understand more deeply about the AV Receiver. Advanced Manual is consisted of the following chapters. r Details on AM/FM Playback

r Playing Music Files on a USB Storage Device r Listening to Internet Radio

r Playing Music with DLNA

r Playing Music Files in a Shared Folder

r Operating Music Files with the Remote Controller r Listening Mode

r Advanced Settings

r Operating Other Components with the Remote Controller r Advanced Speaker Connection

r Connecting and Operating Onkyo RI Components

r Control Function between the Unit and External Component r Firmware Update

r Troubleshooting

r Reference Information

Features

r Equipped with 7 channel amplifier r THX Select2 Plus certified

r Incorporates Qdeo™ technology for HDMI video upscaling

r Equipped with 4K/60 Hz Passthrough-compatible HDMI IN/OUT jacks (only IN1 to IN4 support 4K)

r Supports the HDMI Through function which allows transmission from playback devices to the TV in standby state

r Supports HDCP2.2, a strict copy-protection for providing high quality content (HDMI IN3/OUT MAIN only)

r Supports ARC (Audio Return Channel) r Supports USB storage playback

r Supports variety of network functions such as Internet

Radio, DLNA, etc.

r Supports MHL-enabled mobile device r Bi-Amping capability

r Lip Sync function to correct deviation of audio and video r Multi-zone function which allows you to play a different

source in another room from the main room

r 32 bit DSP (Digital Signal Processor) with excellent calculation performance

r Music Optimizer™ for Compressed Digital Music files r Phase Matching Bass System

r Automatic speaker setup available using supplied calibrated microphone (AccuEQ Room Calibration)

r Supports playback of MP3, WMA, WMA Lossless, FLAC, WAV, Ogg Vorbis, Apple Lossless, DSD, Dolby TrueHD via network and USB storage device (the supported formats will differ depending on the use environment)

r ISF (Imaging Science Foundation) Video Calibration

Advanced Manual found here http://integraworldwide.com/manual/dtr406/adv/en.html

Supplied Accessories

					Indoor FM antenna	--- (1)
					AM loop antenna ---	(1)
					Color labels for speaker cable		(1)
					Remote controller (RC-883M)		(1)
					Batteries (AA/R6) ---	(2)
					Power cord --- (1)
					Speaker setup microphone ---		(1)

¼The number in parenthesis indicates the quantity. On packaging, the letter at the end of the product name indicates the color.

How to use the remote controller

Remote control sensor

AV Receiver

Batteries (AA/R6)

Approx. 16 ft. (5 m)

¼If you do not use the remote controller for a long time, remove the batteries to prevent leakage.

¼Note that keeping consumed batteries inside may cause corrosion resulting in damage of the remote controller.

2

Step 1: Connections

Personal computer

HDMI

OUT

HDMI cable

HDMI

OUT

Game console		Set-top box/Digital
		video recorder, etc.

1 Connecting the TV and players

Important: The power cord must be connected only after all other connections are completed.

HDMI cable connection

The unit has many HDMI jacks on its rear panel and each of them corresponds to an input selector button of the same name on the front panel. For example, a Blu-ray Disc player will be connected to the IN 1 jack and the BD/DVD button on the front panel will be used to listen to the playback sound (if the player is CEC compliant, input will be switched automatically). If you add another Blu-ray Disc player, you can use any other jack than IN 1. It is possible to change assignment of the input jacks and input selector buttons.

TV

HDMI

IN

	HDMI	HDMI
	OUT
		OUT

Satellite/Cable set-top box, etc.

To use the ARC function, connect to the ARC compatible HDMI jack of the TV and make an appropriate setting on the unit. See "2nd Step : Source Connection" of "Step 2: Setting Up".

HDMI

OUT

Blu-ray Disc/

DVD player

For how to make settings, see the Advanced Manual (http:// integraworldwide.com/manual/dtr406/adv/en.html).

To connect the TV and the unit, connect the HDMI OUT MAIN jack of the unit and the HDMI IN jack of the TV using an HDMI cable. With this connection, it becomes possible to display the setting screen of the unit on the TV or transmit video/audio signals from the player to the TV. If your TV supports ARC (Audio Return Channel), it is possible to play the TV sound with the AV receiver's speakers with this

connection only. If your TV does not support ARC, you need, in addition to the HDMI OUT MAIN jack connection, a digital optical cable connection between the digital audio out optical jack of the TV and the DIGITAL IN OPTICAL jack of the unit or an analog audio (RCA) cable connection between the audio output jack of the TV and the TV/CD analog audio input jack of the unit.

z Connection with a TV not supporting ARC

TV

AUDIO

OUT

DIGITAL

OPTICAL

OUT

¼Select an appropriate connection for your TV.

Another TV can be connected to the HDMI OUT SUB jack.

In this case, change the setting accordingly. You can set up by viewing the guidance displayed on the TV screen. Select the item with the cursor buttons of the remote controller and press Enter to confirm your selection. Press Receiver and

3

then Home on the remote controller, select "Setup" - "1. Input/Output Assign" - "Monitor Out" and set the default value of "MAIN" to "SUB" or "MAIN+SUB". With the sub output, the operation screen for Internet function or USB playback can be displayed. It is also possible to use the multi-zone function with this jack. For details, see the section 5 "Using the multi-zone function" of "Step 3: Playing Back".

The unit supports the HDMI Through function that allows transmission from players to the TV even if the unit is in standby. You have to modify the settings to enable the input selection link with CEC compliant device, connection with ARC compatible TV, and HDMI Through function. See "2nd Step : Source Connection" of "Step 2: Setting Up".

r To enjoy HDCP2.2 protected video, connect the player to the IN3 jack and the TV to the HDMI OUT MAIN jack of the unit. Your player and TV need to support HDCP2.2.

r To play 4K or 1080p video, use the high speed HDMI cable.

r It is possible to send video and audio of an MHLenabled mobile device by connecting the MHL-enabled mobile device to the AUX Input HDMI/MHL jacks on the front panel.

Connecting Components without HDMI

If your AV component does not have HDMI jack, use an available jack of your component for cable connection with this unit. Just as the HDMI jacks, other jacks on this unit have a preassigned input selector button on the front panel. See the name of the input selector button shown with the jack when connecting the device.

Audio signal connection

1 Digital connection: Use a digital optical cable (OPTICAL) or digital coaxial cable (COAXIAL) for connection with a player.

Digital optical cable (OPTICAL)

¼ As the digital in optical jack of the unit has a cover, push in the cable of the player against the cover as it is turned inside.

Digital coaxial cable (COAXIAL)

2 Analog connection: Use an analog audio (RCA) cable for connection with a player.

To enjoy multi-zone playback of audio of a CD player or such other player without HDMI output jack, you need to use the RCA cable to connect the corresponding jacks of the player and this unit. For details on the multizone function, see the section 5 "Using the multi-zone function" of "Step 3: Playing Back".

Analog audio (RCA) cable

3 Connection with turntable: If it uses an MM type cartridge and does not have a built-in audio equalizer, connect it to the 3 PHONO jack. If the connected turntable has a built-in audio equalizer, connect it to the 2 TV/CD jack.

¼If it uses an MC type cartridge, install an audio equalizer compatible with MC type cartridge between the unit and the turntable by connecting it to the 2 TV/CD jack. For details, refer to the turntable's instruction manual.

¼If the turntable has a ground wire, connect it to the GND terminal of this unit. If connecting the ground wire increases noise, disconnect it.

Video signal connection

The unit has a video upconversion function. For details, see the section on the right.

4 Use a component video cable to connect a TV with component video input jacks and a player with component video output jacks.

Component video cable

¼ Its transmitted video has higher quality than that of composite video cable.

5 Use a composite video cable to connect a TV with composite video input jack or a player with composite video output jack.

Composite video cable

Step 1: Connections

1	4	5
	3	2

Video signals input to the composite video input jack or the COMPONENT VIDEO input jacks will be upconverted to HDMI signals and then output from the HDMI output jack.

Note that it is not possible to convert digital audio input signals to analog or vice versa.

AV Receiver

¼When you upconvert video signals input to the COMPONENT VIDEO jacks and output them from the HDMI OUT jack, set the output resolution of the player to 480i/576i. If the input has 480p/576p or higher resolution, a message prompting you to change the resolution setting will appear. If your player does not support 480i/576i output, use the composite video jack.

¼If multiple video signal inputs are put into one input system, the output will be made in the order of HDMI, component video, and composite video.

4

2 Connecting speakers

Important: The power cord must be connected only after all other connections are completed.

12

3 9F

6

45

78

1 2 Front speakers

3 Center speaker

4 5 Surround speakers

6Subwoofer

7 8 Surround back speakers

9 F Height speakers

r 5.1 ch: 1 2 3 4 5 6

r 7.1 ch: 1 2 3 4 5 6 + 7 8 or

1 2 3 4 5 6 + 9 F

r Up to two subwoofers can be connected.

r To use the multi-zone function, see the section 5 "Using the multi-zone function" of "Step 3: Playing Back".

Step 1: Connections

2	1
Front R	Front L

3

Center

If there is only one

surround back

speaker, connect it to

the BACK or HEIGHT

L terminal.

6

6

5

8F

79

4

Subwoofer with built-

Subwoofer with built-

Surround R

Surround back/

Surround back/

Surround L

in power amplifier

in power amplifier

height R

height L

Important: %QPPGEV URGCMGTU YKVJ ŝ VQ ŝ KORGFCPEG

and press Enter to confirm your selection. To return to the

You have to modify the setting if any of the speakers have

previous screen, press Return. Press Receiver and then

ŝ QT OQTG VQ NGUU VJCP ŝ KORGFCPEG ;QW ECP UGV WR D[

Home on the remote controller. Select "Setup" - "2.Speaker

viewing the guidance displayed on the TV screen. Select

Setup" - "Speaker Settings" - "Speaker Impedance" and

the item with the cursor buttons of the remote controller

change the default value from "6ohms" to "4ohms".

5

1/2"-5/8"(12-15 mm)

Cut and remove the plastic coating from the end of the speaker cable, twist the core and connect it to the terminal. Make correct connection between the unit's jacks and speaker's jacks (+ to + and - to -) for each channel. If connection is wrong, a bass sound may become poor due to reverse phase. Attaching the supplied colored speaker cable labels to the + side on the both ends of each channel's cable will help correct connection. The subwoofer jack supports connection of a subwoofer with built-in power amplifier. Set the cut-off filter selection switch of the subwoofer to DIRECT. If the subwoofer does not have a cut-off filter selection switch but has a cut-off frequency adjusting dial, turn it to the maximum frequency. If your subwoofer does not have built-in power amplifier, you can connect a power amplifier between the unit and the subwoofer.

r The speaker setting is 7.1 ch at the time of purchase. You can change it manually or by using automatic speaker setting.

r Short-circuiting the + cable and - cable or contacting the cable core to the rear panel of the unit may cause failure. Also do not connect two or more cables to one speaker terminal or one speaker to several terminals.

r Using a speaker with less impedance than the setting may result in failure.

When using commercially available banana plugs: tighten the speaker terminals to the end and then insert the banana plugs. Do not insert the cable core directly into the hole for banana plug of speaker terminal.

(North American model)

3 Other connections

AM/FM antenna connections

Connect the antennas to listen to AM/FM broadcast. When listening to the broadcast for the first time, adjust the antenna position and orientation to get the best reception.

AM loop antenna (supplied)

Indoor FM antenna (supplied)

Fix with a tack on the wall.

(North American model)

(Australian model)

Step 1: Connections

Network connection

You can enjoy Internet radio and DLNA by connecting the unit to LAN. Connect the Ethernet cable to the Ethernet port of the router.

Internet radio

PC

Router

NAS

Headphones connection

Connect stereo headphones with a standard plug (1/4 inch or ø 6.3 mm) to the PHONES jack on the front panel. Sound from the speakers will be off while you are using the headphones.

r If you selected any other listening mode than Stereo, Mono and Direct, connecting headphones will switch the listening mode to Stereo.

Assemble the AM loop antenna (supplied).

6

Step 2: Setting Up

Important: When the unit is turned on for the first time, the setup wizard of the section 2 will automatically be launched. If you use the setup wizard to make the initial setup, connect a TV to the HDMI OUT MAIN jack of the unit via HDMI connection.

1 Turning the power on

Connect the power cord to the outlet. Press zOn/Standby on the main unit or zReceiver on the remote controller to turn the unit on or to standby mode.

Initial Setup

Language Select

English

Deutsch

Français

Español

Italiano

Nederlands

Svenska

HOME Exit

¼This unit includes a removable power cord. Connect the power cord to AC INLET of the unit and then connect to the outlet. Always disconnect the outlet side first when disconnecting the power cord. When the

unit is turned on, a large instantaneous current may flow affecting functionality of the computer and other devices. It is recommended to use a separate outlet from that for the computer or such other sensitive devices.

Firmware update notification: If the unit is connected via LAN and there is firmware update available, the "Firmware Update Available" message will appear. To execute updating, select "Update Now" with the cursor buttons of the remote controller and press Enter. When "Completed!" appears, press zOn/Standby on the main unit to turn the unit into standby mode. Then updating will be completed.

2Making the Initial Setup with the Setup Wizard

Read before starting the procedure: Set up by answering the guidance displayed on the TV screen. Select the item with the cursor buttons of the remote controller and press Enter to confirm your selection. To return to the previous screen, press Return.

r If you terminate the procedure on the way or change the setting made in the initial setup and want to call up the setup wizard again, press Receiver and then Home on the remote controller, select "Setup" - "7.Hardware Setup" - "Initial Setup", and press Enter.

Select the language first. In the next screen, the summary of the setup wizard as below will be displayed. Select "Yes" in this screen and press Enter on the remote controller.

Initial Setup

Welcome to initial setup. Have you connected all the speakers and devices?

Before starting, please connect speakers and sources.

Now, would you like to start initial setup? 1st Step : AccuEQ Room Calibration 2nd Step : Source Connection

3rd Step : Remote Mode Setup 4th Step : Network Connection

Yes

No

HOME Exit

The setup wizard proceeds in the four steps as below.

1st Step : AccuEQ Room Calibration

2nd Step : Source Connection

3rd Step : Remote Mode Setup

4th Step : Network Connection

1st Step : AccuEQ Room Calibration

The test tone coming from each speaker will be measured to enable setting of the number of speakers, volume level, each speaker's optimum crossover frequencies, and distance from the primary listening position, and also enable correction of distortion caused by the room acoustic environment.

Initial Setup

AccuEQ Room Calibration

This step you can automatically calibrate your room to get correct surround sound. Would you like to cailbrate your room now or later?

Do it Now

Do it Later

HOME Exit

1.Place the speaker setup microphone.

When the start screen above is displayed, before starting the procedure, place the supplied speaker setup microphone at the measurement position by referring to the figure below.

TV

Listening area	Measurement position
	with microphone

¼Correct measurement will not be possible if the microphone is held by hand. Measurement is not possible if headphones are being used.

¼The subwoofer sound may not be detected since it is extremely low frequencies. Raise the subwoofer volume to around the half of its maximum volume and make its frequency to the maximum level.

¼A loud test tone will be heard during measurement. Measurement may be interrupted if there is ambient noise or radio frequency interference. Close the window and turn off the home appliance and fluorescent light.

7