For HP Internal Use Only Warranty
©Copyright Hewlett-Packard Company 2006
This document contains proprietary information that is protected by copyright. All rights are reserved. No part of this document may be photocopied, reproduced, or translated to another language without the prior written consent of Hewlett-Packard Company.
First Edition, March 2006
The information contained in this document is subject to change without notice.
Hewlett-Packard makes no warranty of any kind with regard to this material, including, but not limited to, the implied warranties of merchantability and fitness for a particular purpose.
Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Content Management Department, Barcelona Division, Hewlett-Packard Espanola, S.A. Avda. Graells, 501
08190 Sant Cugat del Valles Spain
WARNING
The procedures described in this manual are to be performed by HP-qualified service personnel only.
Electrical Shock Hazard
Serious shock hazard leading to death or injury may result if you do not take the following precautions:
-Ensure that the ac power outlet (mains) has a protective earth (ground) terminal.
-Disconnect the Printer from the power source prior to performing any maintenance.
-Prevent water or any other liquids from running onto electrical components or circuits, or through openings in the enclosure.
Electrostatic Discharge
Refer to the beginning of Chapter 4of this manual, for precautions you should take to prevent damage to the Printer circuits from electrostatic discharge.
Safety Symbols
General definitions of safety symbols are given immediately after the table of contents.
WARNING
The Warning symbol calls attention to a procedure, practice, or the like, which, if not correctly performed or adhered to, could result in personal injury. Do not proceed beyond a Warning symbol until the indicated conditions are fully understood and met.
CAUTION
The Caution symbol calls attention to an operating procedure, practice, or the like, which, if not correctly performed or adhered to, could result in damage to or destruction of part or all of the product. Do not proceed beyond a Caution symbol until the indicated conditions are fully understood and met.
This Service Manual contains information necessary to test, calibrate and service:
HP Designjet 10ps Printer (Model C7790A)
HP Designjet 20ps Printer (Model C7790B)
HP Designjet 30 Printer (Model C7790D)
HP Designjet 30n Printer (Model C7790E)
HP Designjet 50ps Printer (Model C7790C)
HP Designjet 70 Printer (Model Q6655A)
HP Designjet 90 Printer (Model Q6656A)
HP Designjet 90r Printer (Model Q6656B)
HP Designjet 100 Printer (Model C7796A)
HP Designjet 100+ Printer (Model C7796C)
HP Designjet 110 Printer (Model C7796B)
HP designjet 110+ Printer (Model C7796D)
HP Designjet 110+nr Printer (Model C7796E)
HP designjet 120 Printer (Model C7791A)
HP Designjet 120nr Printer (Model C7791B)
HP Designjet 130 Printer (Model C7791C)
HP Designjet 130nr Printer (Model C7791D)
For information about using these printers, refer to the corresponding User and Quick Reference Guides.
The procedures described in this Service Manual are to be performed by HP Certified service personnel only.
Part Numbers for Printer options, accessories and service parts are located in Chapter 7.
A small arrow is used to indicate other parts of the Service Manual where you can find information related to the topic you are consulting.
-2 |
HP Designjet Ultra Low End Printer Service Manual |
Table of Contents
Table of Contents |
1 |
Test Prints 1-1
System Error Codes 2-1
System Maintenance Utility 3-1
Utilities 4-1
Calibrations 5-1
Parts and Diagrams 6-1
Removal and Installation 7-1
Maintenance 8-1
HP Designjet Ultra Low End Printer Service Manual |
-3 |
Test Prints |
1 1 |
Usage Report Page 1-2
Information Page 1-3
NVM Contents Page 1-5
HP Designjet Ultra Low End Printer Service Manual |
1-1 |
Test Prints
The Usage Report Page contains the following information:
Printer Model Name.
Printer Model Number.
Printer Serial Number.
Date of last print job received.
Total ink consumed.
Date of first print job received.
Number of pages printer (media size/media type/print quality setting).
To print the Usage Report Page, hold the power button down and press the resume button once.
Press Resume button once
Hold Power Button
Sample of the
Usage Report Page
1-2 |
HP Designjet Ultra Low End Printer Service Manual |
Test Prints
The Information Page contains the following information:
Printer Identification.
Printer Status.
Printer Usage.
Ink Consumable Identification.
Ink Consumables Status.
Ink Consumables Usage.
Network Card Information.
To print the Information Page, hold the power button down and press the resume button 4 times.
Press Resume button 4 times
Hold Power Button
Sample of the
Information Page
(page 1 of 3)
HP Designjet Ultra Low End Printer Service Manual |
1-3 |
Test Prints
Sample of the
Information Page
(page 2 of 3)
Sample of the
Information Page
(page 3 of 3)
1-4 |
HP Designjet Ultra Low End Printer Service Manual |
Test Prints
The NVM Contents Page contains the following information:
EEROM values dump containing all the values stored in the EEROM (Calibration, etc.)
Printheads Acumen dump
Cartridges Acumen dump.
To print the NVM Contents Page, hold the power button down and press the cancel button once and the resume button twice.
Press Resume
button once
Press Resume button twice
Hold Power Button
Sample of the
NVM Contents Page
(page 1 of 3)
HP Designjet Ultra Low End Printer Service Manual |
1-5 |
Test Prints
Sample of the
NVM Contents Page
(page 2 of 3)
Sample of the
NVM Contents Page
(page 3 of 3)
1-6 |
HP Designjet Ultra Low End Printer Service Manual |
System Error Codes |
21 2 |
System Error Codes 2-4 Warnings 2-11
Startup track mode 2-19 Emergency Firmware Upgrade 2-26
System Error Codes - Explanation 2-27
HP Designjet Ultra Low End Printer Service Manual |
2-1 |
System Error Codes
The following pages contain a list of system error codes and their respective descriptions and recommended corrective actions. Only try one recommended action at a time and check if the error code has disappeared.
Since the front panel can only display graphics, the error code needs to be determined by counting the bars on the front panel (as shown below).
|
|
|
|
|
|
|
|
|
|
|
|
Failing Subsystem |
Recovery |
||
Action |
|||
|
|
1 unit
2 units
flashing
7 |
9 |
0 |
4 |
First 2 digits of |
Second 2 digits |
||
the error code |
of the error code |
Refer to Page 2-27 for an explanation on the construction of the Error Codes and Warnings.
2-2 |
HP Designjet Ultra Low End Printer Service Manual |
System Error Codes
Error Codes will normally be displayed directly on the front panel (but can also be seen on the Information Page) and will require some kind of intervention to resolve the problem. Warnings will not be displayed on the front panel, but will instead only appear on the Information Page, therefore allowing the user to continue operating the printer without the need of an intervention.
System Errors
Warnings
You can also obtain report of the System Error and Warnings through the DesignJet System Maintenance Tool.
HP Designjet Ultra Low End Printer Service Manual |
2-3 |
|
System Error Codes |
System Error: |
01:10 |
Problem |
Electronics Module failure. |
Description: |
|
Corrective Action: Replace the Electronics Module Page 7-18. |
|
System Error: |
01:12 |
Problem |
Electronics Module failed during the firmware upgrade OR the Electronics |
Description: |
Module failed during initialization. |
Corrective Action: Try the following:
If the Electronics Module failed during initialization, you must perform the Electronics Test to determine the cause of the failure.
If the Electronics Module failed during the firmware upgrade, first perform an emergency firmware upgrade ( Page 2-26).
If an emergency firmware upgrade is NOT possible or it didn’t work, replace the Electronics Module Page 7-18.
System Error: |
02:10 |
Problem |
Carriage failure. |
Description: |
|
Corrective Action: Replace the Carriage Assembly Page 7-35. |
|
System Error: |
04:13 |
Problem |
Generic Firmware Error (Network Card). |
Description: |
|
Corrective Action: Unplug the power cable from the printer and wait a few seconds. Plug in the power cable again and check if the Error Code has disappeared. If the error code continues, refer to the Jetdirect Card Service Manual and Service Notes.
System Error: |
08:11 |
Problem |
Front Panel cannot be detected. |
Description: |
|
Corrective Action: Reconnect the Front Panel.
2-4 |
HP Designjet Ultra Low End Printer Service Manual |
System Error Codes
System Error: |
11:10 |
Problem |
Trailing Cable Failure. |
Description: |
|
Corrective Action: Try the following:
Replace the Carriage Assembly Page 7-35.
If the Error Code continues, replace the Electronics Module Page 7-18.
Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
System Error: |
11:11 |
Problem |
Trailing Cable is badly connected. |
Description: |
|
Corrective Action: Try the following:
Reconnect the Trailing Cable correctly to the Electronics Module.
If the Error Code continues, replace the Carriage Assembly Page 7-35.
System Error: |
21:10 |
Problem |
Service Station failure. |
Description: |
|
Corrective Action: Replace the Service Station Assembly Page 7-24. |
|
System Error: |
22:10 |
Problem |
Ink Supply Station failure. |
Description: |
|
Corrective Action: Replace the Ink Supply Station Page 7-14. |
|
System Error: |
35:01 |
Problem |
No Cleanout Assembly detected while loading media. |
Description: |
|
Corrective Action: Try the following:
Remove the Cleanout Assembly and install it again correctly.
Replace the Cleanout Interconnect PCA.
If the Error Code continues, replace the Cleanout Assembly.
Only replace one component at a time and check if the error has gone before replacing another component. Using this procedure you will be able to determine exactly which component failed.
HP Designjet Ultra Low End Printer Service Manual |
2-5 |
System Error Codes |
|
System Error: |
37:01 |
Problem |
Automatic roll motor shutdown. |
Description: |
|
Corrective Action: Try the following:
If this error code was caused by a paper jam, unplug the power cable from the printer and clear the blockage. Plug in the power cable again and check if the Error Code has disappeared.
If there is no paper jam or if recovering the paper jam does not resolve the problem, then replace the Automatic Roll System (the error could be caused by anything that stalls the motor).
System Error: |
37:10 |
Problem |
Automatic roll home position error. |
Description: |
|
Corrective Action: Replace the Automatic Roll System (the error could be caused by anything that causes the home position not to be detected or not to be the correct one - electrical sensors, internal mechanical problems, etc.).
System Error: |
42:10 |
Problem |
Carriage Motor failure (short-circuit). |
Description: |
|
Corrective Action: Replace the Carriage Motor Assembly Page 7-29.
2-6 |
HP Designjet Ultra Low End Printer Service Manual |
|
System Error Codes |
System Error: |
56:10 |
Problem |
Error during the calibration of the motor encoder system or a problem |
Description: |
finding the zero position on the Encoder Disc. |
Corrective Action: Try the following:
Replace the Paper-Axis Motor Drive Assembly Page 7-75.
Replace the Encoder Disc.
|
Make sure you recalibrate the Paper-Axis after replacing the |
|
Paper-Axis Motor Drive Assembly or the Encoder Disc. |
|
Only replace one component at a time and check if the error |
|
has gone before replacing another component. Using this |
|
procedure you will be able to determine exactly which |
|
component failed. |
System Error: |
56:13 |
Problem |
Error during the calibration of the Line-feed Motor/Encoder system. |
Description: |
|
Corrective Action: Unplug the power cable from the printer and wait a few seconds. Plug in the power cable again and check if the Error Code has disappeared.
System Error: |
61:05 |
Problem |
Firmware Upgrade or Color Calibration was rejected because the file was |
Description: |
sent in the wrong format. |
Corrective Action: |
Upgrade the RIP software or the Designjet System Maintenance Tool. |
System Error: |
62:04, 63:04, 64:04 and 65:04 |
Problem |
I/O module error (62 = parallel; 63 = Network; 64 = USB). |
Description: |
|
Corrective Action: Try the following:
Unplug the power cable from the printer and wait a few seconds. Plug in the power cable again and check if the Error Code has disappeared.
If the Error Code reappears, upgrade the firmware.
System Error: |
71:03 |
Problem |
Generic Firmware Error (Out of memory). |
Description: |
|
Corrective Action: Try the following:
Unplug the power cable from the printer and wait a few seconds. Plug in the power cable again and check if the Error Code has disappeared.
If the Error Code reappears, check for a new Firmware release.
HP Designjet Ultra Low End Printer Service Manual |
2-7 |
System Error Codes |
|
System Error: |
71:14 |
Problem |
Memory Management Error (Out of memory during firmware upgrade). |
Description: |
|
Corrective Action: Try the following:
Unplug the power cable from the printer and wait a few seconds. Plug in the power cable again and check if the Error Code has disappeared.
If the Error Code reappears, perform an emergency firmware upgrade Page 26.
System Error: |
72:04 |
Problem |
Generic Firmware Error (expected). |
Description: |
|
Corrective Action: Try the following:
Unplug the power cable from the printer and wait a few seconds. Plug in the power cable again and check if the Error Code has disappeared.
If the Error Code reappears, check for a new Firmware release.
If possible, request the user to provide the following information which can be found on the information page:
–Firmware Release.
–Filename.
–Line.
System Error: |
74:12 |
Problem |
Firmware Upgrade Error (Memory size check failed during firmware upgrade). |
Description: |
|
Corrective Action: Try the following:
Perform the automatic troubleshooting procedure (requires a special firmware upgrade file that must be provided by the manufacturing division).
System Error: |
79:04 |
Problem |
Generic Firmware Error (unexpected). |
Description: |
|
Corrective Action: Try the following:
Unplug the power cable from the printer and wait a few seconds. Plug in the power cable again and check if the Error Code has disappeared.
If the Error Code reappears, check for a new Firmware release.
If possible, request the user to provide the following information which can be found on the information page:
–Firmware Release.
–Filename.
–Line.
2-8 |
HP Designjet Ultra Low End Printer Service Manual |
|
|
System Error Codes |
System Error: |
81:01 |
|
Problem |
Paper-Axis |
shutdown - usually a paper-jam caused by a blockage of the |
Description: |
Paper-axis System. |
Corrective Action: Try the following:
If this error code was caused by a paper-jam, unplug the power cable from the printer and clear the blockage. Plug in the power cable again and check if the Error Code has disappeared
If this error code appeared but was NOT caused by a paper jam, replace the Paper-Axis Motor Drive Assembly Page 7-75.
System Error: |
81:12 |
Problem |
Media Advance error. |
Description: |
|
Corrective Action: This error usually appears during the paper-advance calibration - Retry the paper-advance calibration.
System Error: |
83:10 |
Problem |
Sheet feeding failure. |
Description: |
|
Corrective Action: Try the following:
Replace the Out-Of-paper Sensor.
Replace the Electronics Module Page 7-18.
System Error: |
85:10 |
Problem |
Paper-Axis Encoder error. |
Description: |
|
Corrective Action: Try the following:
Make sure that the Encoder Sensor cable is connected correctly.
Replace the Paper-Axis Motor Drive Assembly Page 7-75.
Replace the Electronics Module Page 7-18.
System Error: |
86:01 |
|
|
Problem |
|
|
|
Scan-axis shutdown - usually a paper-jam caused by a blockage of the Scan- |
|||
Description: |
axis System. |
Corrective Action: Try the following:
Check that there are no obstacles in the Scan-Axis which stops the Carriage from moving freely.
Too much friction in the Slider Rod, try lubricating the Slider Rod.
The Carriage is bumping into the Service Station. If the Carriage is stuck at the right hand side of the Printer and cannot be moved out to the center of the Print Platen it is because the Service Station cannot uncap
HP Designjet Ultra Low End Printer Service Manual |
2-9 |
System Error Codes |
|
|
the printheads. In this case replace the Service Station Assembly Page |
|
7-24. |
|
Check that the belt is correctly installed and not damaged. |
|
Check that the Turnaround Pulley is correctly installed. |
|
Replace the Carriage Motor Assembly Page 7-29. |
System Error: |
86:11 |
Problem |
Scan-axis shutdown during initialization. Typically, this error occurs when the |
Description: |
printer detects an incorrect length. |
Corrective Action: Try the following:
Unplug the power cable from the printer and wait a few seconds. Plug in the power cable again and check if the Error Code has disappeared.
Check that the Paper-Axis Drive Motor Assembly is correctly installed and that the bushing is correctly locked into position.
Check that the Carriage moves freely and DOES NOT bump into the Service Station.
If the Printheads are not installed, maybe the carriage cover is not closed completely.
If the Error Code continues, replace the Carriage Assembly Page 7-35.
2-10 |
HP Designjet Ultra Low End Printer Service Manual |
System Error Codes
|
Warnings |
System Error: |
01:11 |
Problem |
The Electronics Module is incorrectly positioned. |
Description: |
|
Corrective Action: Reseat the Electronics Module by Removing it from the Printer ( Page 7-18) and installing it again in the correct position.
System Error: |
01:12 |
Problem |
Electronics Module Error. |
Description: |
|
Corrective Action: The Electronics Module EEPROM is flagged as empty and must be upgraded with the contents of the Carriage EEPROM, but the Carriage is also flagged as empty. The backup is not performed. This is the result of an error during the manufacturing or the repair process. Therefore the Electronics Module must be reconfigured.
System Error: |
02:10 |
Problem |
Carriage failure. |
Description: |
|
Corrective Action: Replace the Carriage Assembly Page 7-35. |
|
System Error: |
270:00 |
Problem |
Black Color Calibration Failure - Black Color Calibration cancelled. |
Description: |
|
Corrective Action: Try the following:
Clean the electrical contacts on the black printhead.
If the error code continues, replace the black printhead.
System Error: |
271:00 |
Problem |
Cyan Color Calibration Failure - Cyan Color Calibration cancelled. |
Description: |
|
Corrective Action: Try the following:
Clean the electrical contacts on the cyan printhead.
If the error code continues, replace the cyan printhead.
HP Designjet Ultra Low End Printer Service Manual |
2-11 |
System Error Codes |
|
System Error: |
272:00 |
Problem |
Magenta Color Calibration Failure - Magenta Color Calibration cancelled. |
Description: |
|
Corrective Action: Try the following:
Clean the electrical contacts on the magenta printhead.
If the error code continues, replace the magenta printhead.
System Error: |
273:00 |
Problem |
Yellow Color Calibration Failure - Yellow Color Calibration cancelled. |
Description: |
|
Corrective Action: Try the following:
Clean the electrical contacts on the yellow printhead.
If the error code continues, replace the yellow printhead.
System Error: |
274:00 (Not applicable to HP DesignJet 70, 100, 100+, 110+) |
Problem |
Light Cyan Color Calibration Failure - Light Cayan Color Calibration |
Description: |
cancelled. |
Corrective Action: Try the following:
Clean the electrical contacts on the light cyan printhead.
If the error code continues, replace the light cyan printhead.
System Error: |
275:00 (Not applicable to HP DesignJet 70, 100, 100+, 110+) |
Problem |
Light Magenta Color Calibration Failure - Light Magenta Color Calibration |
Description: |
cancelled. |
Corrective Action: Try the following:
Clean the electrical contacts on the light magenta printhead.
If the error code continues, replace the light magenta printhead.
System Error: |
35:01 |
Problem |
No Cleanout Assembly (or Duplexer, if installed) detected while loading |
Description: |
media. |
Corrective Action: Try the following:
Remove the Cleanout Assembly ( Page 7-31) (or Duplexer, if installed) and install it again correctly.
Replace the Duplexer Interconnect PCA.
If the Error Code continues, replace the Cleanout Assembly Page 7-31.
2-12 |
HP Designjet Ultra Low End Printer Service Manual |
|
System Error Codes |
System Error: |
58:10 |
Problem |
Problem detected in the color sensor system. |
Description: |
|
Corrective Action: Replace the Carriage Assembly Page 7-35. |
|
System Error: |
61:05 |
Problem |
Language interpreting error. This is usually and error produced while |
Description: |
parsing a file. There is probably an incompatibility between the driver and |
|
the firmware. |
Corrective Action: Upgrade the RIP software or the Designjet System Maintenance Tool. |
|
System Error: |
65:01 |
Problem |
Communication Failure. |
Description: |
|
Corrective Action: Try the following:
Unplug the power cable from the printer and check the cable connections (Parallel, USB and Network cables). Plug in the power cable again and check if the Error Code has disappeared.
System Error: |
66:02:1 (Only applicable to HP DesignJet 30, 30n, 90, 90r, 130, 130nr) |
Problem |
Horizontal clipping. May happen when the roll ends in the middle of printing |
Description: |
an image. Could also happen when multi-pick occurs and two sheets are |
|
loaded together and they do not completely overlap. |
Corrective Action: Make sure the image size is within the selected WIDTH of the sheet.
System Error: |
66:02:2 (Only applicable to HP DesignJet 30, 30n, 90, 90r, 130, 130nr) |
Problem |
Vertical clipping. May happen when the roll ends in the middle of printing an |
Description: |
image. Could also happen when multi-pick occurs and two sheets are loaded |
|
together and they do not completely overlap. |
Corrective Action: Make sure the image size is within the selected LENGTH of the sheet. |
|
System Error: |
71:14 |
Problem |
Out-of-memory while trying to process the firmware upgrade file. Probably this |
Description: |
is a firmware bug, because the firmware should free up enough memory to |
|
perform the firmware upgrade process correctly. |
Corrective Action: Perform an emergency firmware upgrade ( Page 2-26).
HP Designjet Ultra Low End Printer Service Manual |
2-13 |
System Error Codes |
|
System Error: |
74:12 |
Problem |
Firmware bug in the firmware upgrade process |
Description: |
|
Corrective Action: Try the following:
Download the special file in order to update the bootlog.
If possible, request the user to provide the following information which can be found on the information page:
–Firmware Release.
–Printer Serial Number.
System Error: |
81:01 |
|
|
Problem |
|
|
|
Paper-Axis shutdown - usually a paper-jam caused by a blockage of the |
|||
Description: |
Paper-axis System. |
Corrective Action: Try the following:
If this error code was caused by a paper-jam, unplug the power cable from the printer and clear the blockage. Plug in the power cable again and check if the Error Code has disappeared
If this error code appeared but was NOT caused by a paper jam, replace the Paper-Axis Motor Drive Assembly Page 7-75.
System Error: |
83:01:1 (Only applicable to HP DesignJet 30, 30n, 70, 100+, 110+, 90, |
|
90r, 120, 120nr, 130, 130nr) |
Problem |
The paper is rejected from the Bypass due to skew. |
Description: |
|
Corrective Action: When manually loading paper from the front of the paper, make sure that it is loaded straight.
System Error: |
83:01:3 (Only applicable to HP DesignJet 70/100plus/110plus) |
Problem |
The paper is rejected from the roll due to skew. |
Description: |
|
Corrective Action: When loading paper from the roll, make sure that it is loaded straight. |
|
System Error: |
94:02:1 (Only applicable to HP DesignJet 30, 30n, 90, 90r, 120, 120nr, |
|
130, 130nr) |
Problem |
User selected Coated Paper and Best mode, but the Color Calibration profile |
Description: |
was obsolete or missing for Coated Paper and the selected print quality setting. |
Corrective Action: Using the System Maintenance Tool, perform Color Calibration for Coated Paper and the selected print quality setting.
2-14 |
HP Designjet Ultra Low End Printer Service Manual |
|
System Error Codes |
System Error: |
94:02:2 (Only applicable to HP DesignJet 120/120nr) |
Problem |
User selected Glossy Paper and Best mode, but the Color Calibration profile |
Description: |
was obsolete or missing for Glossy Paper and the selected print quality setting. |
Corrective Action: Using the System Maintenance Tool, perform Color Calibration for Glossy Paper and the selected print quality setting.
System Error: |
94:02:3 (Only applicable to HP DesignJet 30, 30n, 90, 90r, 120, 120nr, |
|
130, 130nr) |
Problem |
User selected Photo Paper and Best mode, but the Color Calibration profile |
Description: |
was obsolete or missing for Photo Paper and the selected print quality setting. |
Corrective Action: Using the System Maintenance Tool, perform Color Calibration for Photo Paper and the selected print quality setting.
System Error: |
94:02:4 (Only applicable to HP DesignJet 30, 30n, 90, 90r, 120, 120nr, |
|
130, 130nr) |
Problem |
User selected Heavy-Weight Coated Paper and Best mode, but the Color |
Description: |
Calibration profile was obsolete or missing for Heavy-Weight Coated Paper |
|
and the selected print quality setting. |
Corrective Action: Using the System Maintenance Tool, perform Color Calibration for HeavyWeight Coated Paper and the selected print quality setting.
System Error: |
94:02:5 (Only applicable to HP DesignJet 30, 30n, 90, 90r, 120, 120nr, |
|
130, 130nr) |
Problem |
User selected Proofing Semi-Gloss Paper and Best mode, but the Color |
Description: |
Calibration profile was obsolete or missing for Proofing Semi-Gloss Paper |
|
and the selected print quality setting. |
Corrective Action: Using the System Maintenance Tool, perform Color Calibration for Proofing Semi-Gloss Paper and the selected print quality setting.
System Error: |
94:02:6 (Only applicable to HP DesignJet 30, 30n, 90, 90r, 130, 130nr) |
Problem |
User selected Photo Matte Paper and Best mode, but the Color Calibration |
Description: |
profile was obsolete or missing for Photo Matte Paper and the selected print |
|
quality setting. |
Corrective Action: Using the System Maintenance Tool, perform Color Calibration for Photo Matte Paper and the selected print quality setting.
System Error: |
94:02:7 (Only applicable to HP DesignJet 30, 30n, 90, 90r, 120, 120nr, |
|
|
130, 130nr) |
|
Problem |
User selected Photo Satin Paper and Best mode, but the Color Calibration |
|
Description: |
profile was obsolete or missing for Photo Satin Paper and the selected print |
|
HP Designjet Ultra Low End Printer Service Manual |
2-15 |
System Error Codes
quality setting.
Corrective Action: Using the System Maintenance Tool, perform Color Calibration for Photo Satin Paper and the selected print quality setting.
System Error: |
94:02:8 (Only applicable to HP DesignJet 30, 30n, 90, 90r, 120, 120nr, |
|
130, 130nr) |
Problem |
User selected Coated Paper and Max dpi, but the Color Calibration profile |
Description: |
was obsolete or missing for Coated Paper and the selected print quality |
|
setting. |
Corrective Action: Using the System Maintenance Tool, perform Color Calibration for Coated Paper and the selected print quality setting.
System Error: |
94:02:9 (Only applicable to HP DesignJet 120/120nr) |
Problem |
User selected Glossy Paper and High Resolution mode, but the Color |
Description: |
Calibration profile was obsolete or missing for Glossy Paper and the |
|
selected print quality setting. |
Corrective Action: Using the System Maintenance Tool, perform Color Calibration for Glossy Paper and the selected print quality setting.
System Error: |
941:02:1 (Only applicable to HP DesignJet 30, 30n, 90, 90r, 120, 120nr, |
|
130, 130nr) |
Problem |
User selected Photo Paper and Max dpi, but the Color Calibration profile |
Description: |
was obsolete or missing for Photo Paper and the selected print quality |
|
setting. |
Corrective Action: Using the System Maintenance Tool, perform Color Calibration for Photo Paper and the selected print quality setting.
System Error: |
941:02:2 (Only applicable to HP DesignJet 30, 30n, 90, 90r, 120, 120nr, |
|
130, 130nr) |
Problem |
User selected Heavy-Weight Coated Paper and Max dpi, but the Color |
Description: |
Calibration profile was obsolete or missing for Heavy-Weight Coated Paper |
|
and the selected print quality setting. |
Corrective Action: Using the System Maintenance Tool, perform Color Calibration for HeavyWeight Coated Paper and the selected print quality setting.
System Error: |
941:02:3 (Only applicable to HP DesignJet 30, 30n, 90, 90r, 120, 120nr, |
|
130, 130nr) |
Problem |
User selected Proofing Semi-Gloss Paper and Max dpi mode, but the Color |
Description: |
Calibration profile was obsolete or missing for Proofing Semi-Gloss Paper |
|
and the selected print quality setting. |
Corrective Action: Using the System Maintenance Tool, perform Color Calibration for Proofing
2-16 |
HP Designjet Ultra Low End Printer Service Manual |
|
System Error Codes |
|
Semi-Gloss Paper and the selected print quality setting. |
System Error: |
941:02:4 (Only applicable to HP DesignJet 30, 30n, 90, 90r, 130, 130nr) |
Problem |
User selected Photo Matte Paper and Max dpi mode, but the Color |
Description: |
Calibration profile was obsolete or missing for Photo Matte Paper and the |
|
selected print quality setting. |
Corrective Action: Using the System Maintenance Tool, perform Color Calibration for Photo Matte Paper and the selected print quality setting.
System Error: |
941:02:5 (Only applicable to HP DesignJet 30, 30n, 90, 90r, 130, 130nr) |
Problem |
User selected Photo Satin Paper and Max dpi mode, but the Color |
Description: |
Calibration profile was obsolete or missing for Photo Satin Paper and the |
|
selected print quality setting. |
Corrective Action: Using the System Maintenance Tool, perform Color Calibration for Photo Satin Paper and the selected print quality setting.
System Error: |
94:04 |
Problem |
Firmware Error (during color calibration). |
Description: |
|
Corrective Action: Try the following:
Unplug the power cable from the printer and wait a few seconds. Plug in the power cable again and check if the Error Code has disappeared.
If the Error Code reappears, check for a new Firmware release.
System Error: |
94:08 |
Problem |
Color Calibration Warning - Color Calibration not cancelled but Color |
Description: |
Calibration values are likely to be incorrect. |
Corrective Action: Try the Color Calibration again, but this time using a different type of media (preferably HP media).
System Error: |
94:10 |
Problem |
Color Calibration Failure - Color Calibration cancelled. |
Description: |
|
Corrective Action: Try the following:
Unplug the power cable from the printer and wait a few seconds. Plug in the power cable again and try the Color Calibration again.
If this error code appears again, check the Color Calibration print:
–If the Color Calibration was printed correctly without any print defects, then check that the media is moving freely (backwards and forwards) while the printer is scanning it.
–If the Color Calibration was printed incorrectly, with some print defects,
HP Designjet Ultra Low End Printer Service Manual |
2-17 |
System Error Codes |
|
|
replace the faulty Printhead of the color where the defects were |
|
noticeable. |
|
If the Error Code continues, replace the Carriage Assembly Page 7-35. |
System Error: |
95:00 |
Problem |
Printhead Alignment Failure - Printhead Alignment cancelled. |
Description: |
|
Corrective Action: Try the following:
Clean the printhead indicated by the printer.
If the error code continues, replace the faulty printhead.
System Error: |
95:02 |
Problem |
Printhead Alignment Failure - Printhead Alignment cancelled. |
Description: |
|
Corrective Action: Try the following:
Unplug the power cable from the printer and wait a few seconds. Plug in the power cable again and try the Printhead Alignment again.
If this error code appears again, check the Printhead Alignment print:
–If the Printhead Alignment was printed correctly without any print defects, then check that the media is moving freely (backwards and forwards) while the printer is scanning it.
–If the Printhead Alignment was printed incorrectly, with some print defects, replace the faulty Printhead of the color where the defects were noticeable.
System Error: |
95:04 |
Problem |
Firmware Error (during Printhead Alignment). |
Description: |
|
Corrective Action: Upgrade the printer to the latest firmware release.
2-18 |
HP Designjet Ultra Low End Printer Service Manual |
System Error Codes
Introduction
The startup track mode is designed to enable you to identify a failing subsystems while the printer is initializing. Startup track mode provides a specific indication of which particular subsystem is failing. This mode is not intended for use by end-users.
Initializing the printer in Startup track mode
To initialize the printer in Startup track mode:
1Hold the ’Continue’ button while connecting the printer to the power supply.
2During the initialization of the printer, the front panel will display a range of code numbers in the form of squares, these code numbers added together represent the various subsystems about to be initialized.
3Once the printer comes to initializing the failing subsystem, the front panel will hang, and all that will be displayed is the failing subsystem.
Interpreting the numbered code system
While the printer is initializing, the front panel will display a sequence of squares in the last two columns. Each position in the last two columns represents a number, all the numbers represented are shown below. To find the failing subsystem, add the numbers together that have a square and refer to the list of numbers with their associated subsystems page 20.
In the example below the printer is initializing and the front panel has stopped and is displaying squares in positions 16, 32, 64 and 4. Add these four values together and you get 116, refer to the list on page 20, and we can see the failing subsystem is the Trailing Cable.
If the display reaches 191, you will need to turn On the printer from the power button. If all the subsystems pass the initialization, the printer will initialize normally and go to the ready status.
HP Designjet Ultra Low End Printer Service Manual |
2-19 |