Hotpoint KRA 631 T C S, KRA 640 B S, KRA 640 X S Manual

KRA 640 X S

KRA 640 B S KRA 640 C (PL) S KRA 631 T C S KRC 640 X

KRC 631 T X

KRC 640 B

KRC 641 D X

KRC 641 D B

KRC 741 D Z

KRC 631 T B

GB English

Operating Instructions

HOB

Contents

Operating Instructions,1 WARNING,2

Description of the appliance-Control Panel5 Installation,8

Start-up and use,12 Precautions and tips,16 Care and maintenance,17

Technical description of the models,18

FR Français

Mode d’emploi Manutenção e cuidados

TABLE DE CUISSON

Sommaire

Mode d’emploi,1 ATTENTION,2

Description de l’appareil-Tableau de bord, 5 Installation,19

Mise en marche et utilisation,23 Précautions et conseils, 27 Nettoyage et entretien,28

Description technique des modèles,29

ES Español

Manual de instrucciones

ENCIMERA

Sumario

Manual de instrucciones,1 ATENCIÓN,2

Descripción del aparato-Panel de control,5 Instalación,30

Puesta en funcionamiento y uso,34 Precauciones y consejos,38 Mantenimiento y cuidados,39 Descripción técnica de los modelos,40

PT Português

Instruções para a utilização

PLANO

Índice

Instruções para a utilização,1 ATENÇÃO,2

Descrição do aparelho-Painel de comandos,5 Instalação, 41

Início e utilização, 45 Precauções e conselhos,49 Manutenção e cuidados,50

Descrição técnica dos modelos,51

DE Deutsch

Bedienungsanleitung KOCHFELD

Inhaltsverzeichnis

Bedienungsanleitung,1

ZUR BEACHTUNG,2

Beschreibung des GerätesBedienfeld,5 Installation, 52

Inbetriebsetzung und Gebrauch,56 Vorsichtsmaßregeln und Hinweise, 60 Reinigung und Pflege, 61

Technische Beschreibung der Modelle, 62

IT Italiano

Istruzioni per l’uso

PIANO COTTURA

Sommario

Istruzioni per l’uso,1 ATTENZIONE,2

Descrizione dell’apparecchioPannello di controllo,5 Installazione, 63

Avvio e utilizzo,67 Precauzioni e consigli,71 Manutenzione e cura,72

Descrizione tecnica dei modelli,72

English

GB WARNING!

•WARNING: The appliance and its accessible parts become hot during use.

•Care should be taken to avoid touching heating elements.

•Children less than 8 years of age shall be kept away unless continuously supervised.

•This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the

hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not

be made by children without supervision.

•WARNING: Unattended cooking on a hob with fat or oil can be dangerous and may result in fire.

•NEVER try to extinguish a fire with water, but switch off the appliance and then cover flame e.g. with a lid or a fire blanket.

•WARNING: Danger of fire: do not store items on the cooking surfaces.

•WARNING: If the surface in glassceramic is cracked, switch off the appliance to avoid the possibility of electric shock.

•Never use steam cleaners or pressure cleaners on the appliance.

•The appliance is not intended to be operated by means of an external timer or separate remote control system.

Français

FR ATTENTION !

•ATTENTION : cet appareil ainsi que ses parties accessibles deviennent très chauds pendant leur fonctionnement.

•Il faut faire attention de ne pas toucher les éléments chauffants.

•Ne laisser s’approcher les enfants de moins de 8 ans à moins qu’ils ne soient sous surveillance constante.

•Le présent appareil peut être utilisé par des enfants de plus de 8 ans et par des personnes présentant des capacités physiques, sensorielles ou mentales réduites ou n’ayant pas l’expérience

ou les connaissances nécessaires, à condition qu’ils soient sous bonne surveillance ou qu’ils aient reçu les instructions nécessaires pour une

utilisation de l’appareil en toute sécurité et à condition qu’ils se rendent compte des dangers encourus. Les enfants ne doivent pas jouer avec l’appareil. Les opérations de nettoyage et d’entretien ne doivent pas être effectuées par des enfants non surveillés.

•ATTENTION : laisser un récipient de cuisson contenant de l’huile ou de la graisse sur le foyer est dangereux et risque d’entraîner un incendie

•Il ne faut JAMAIS essayer d’éteindre une flamme ou un incendie avec de l’eau ! Il faut éteindre l’appareil et couvrir la flamme avec un couvercle, par exemple, ou avec une couverture anti-feu.

•ATTENTION : risque d’incendie : ne pas laisser d’objets sur les surfaces de cuisson.

•ATTENTION : si la surface vitrocéramique est fêlée, éteindre l’appareil afin d’éviter tout risque d’électrocution.

•Ne jamais nettoyer l’appareil avec des nettoyeurs vapeur ou haute pression.

•Cet appareil ne peut pas être allumé au moyen d’un temporisateur extérieur ou d’un système de commande à distance séparé.

2

Español

ES ATENCIÓN !

•ATENCIÓN: Este aparato y sus partes accesibles se calientan mucho durante el uso.

•Por lo tanto, es importante evitar tocar los elementos calentadores.

•Mantenga alejados a los niños menores de 8 años si no son continuamente vigilados.

•El presente aparato puede ser utilizado por niños mayores de 8 años y por personas con

capacidades físicas, sensoriales o mentales disminuidas o sin experiencia ni conocimientos, si se encuentran bajo una adecuada vigilancia o si han sido instruidos sobre el uso del aparato de modo seguro y comprenden los peligros relacionados con el mismo.

Los niños no deben jugar con el aparato. Las operaciones de limpieza y de mantenimiento no

deben ser realizadas por niños sin vigilancia.

•ATENCIÓN: Dejar un quemador con grasas o aceites sin vigilancia puede ser peligroso y provocar un incendio.

•NUNCA intente apagar una llama/ incendio con agua, se debe apagar el aparato y cubrir la llama, por ejemplo, con una tapa o con una manta ignífuga.

•ATENCIÓN: Riesgo de incendio: no deje objetos sobre las superficies de cocción.

•ATENCIÓN: Si la superficie de vitrocerámica está agrietada, apague el aparato para evitar sacudidas eléctricas.

•No utilice nunca limpiadores a vapor o de alta presión para la limpieza del aparato.

•El aparato no se debe poner en funcionamiento a través de un temporizador externo o de un sistema de mando a distancia.

Português

PT ATENÇÃO !

•ATENÇÃO: Este aparelho e as suas partes acessíveis aquecem muito durante a utilização.

• É preciso ter atenção e evitar tocar os	GB
elementos que aquecem.

•Manter afastadas as crianças com menos de 8 anos, caso não estejam a ser vigiadas.

•O presente aparelho pode ser utilizado por crianças com mais de 8 anos e por pessoas com capacidades físicas, sensoriais ou mentais reduzidas ou com pouca experiência e conhecimentos, caso sejam adequadamente vigiadas ou

caso tenham recebido instruções em relação ao uso do aparelho de forma segura e tenham conhecimento dos perigos associados. As crianças não devem brincar com o aparelho. As operações de limpeza e manutenção não devem ser efectuadas por crianças sem vigilância.

•ATENÇÃO: Deixar um fogão com gordura e óleo sem vigilância pode ser perigoso e provocar um incêndio.

•NUNCA tente apagar as chamas com água. É necessário desligar o

aparelho e cobrir as chamas com uma tampa ou com uma manta ignífuga.

•ATENÇÃO: Risco de incêndio: não deixe objectos sobre as superfícies de cozedura.

•ATENÇÃO: Se a superfície vitrocerâmica estiver rachada, desligue o aparelho para evitar a possibilidade de choques eléctricos.

•Nunca utilize equipamento de limpeza a vapor ou de alta pressão para limpar o aparelho.

•O aparelho não é destinado a ser colocado em funcionamento por meio de um temporizador externo ou por um sistema de comando à distância separado.

3

DE	Deutsch	IT	Italiano
	ZUR BEACHTUNG !		ATTENZIONE!

•ZUR BEACHTUNG: Bei Gebrauch wird dieses Gerät und alle zugänglichen Teile sehr heiß.

•Es ist darauf zu achten, dass die Heizelemente nicht berührt werden.

•Kinder unter 8 Jahren, die nicht ständig beaufsichtigt sind, von dem Gerät fernhalten.

•Das Gerät darf von Kindern ab 8 Jahren und Personen mit eingeschränkten körperlichen, geistigen oder Wahrnehmungsfähigkeiten oder

aber ohne ausreichende Erfahrung und Kenntnis verwendet werden, vorausgesetzt sie werden ausreichend überwacht oder sie wurden in den sicheren Gebrauch des Geräts eingewiesen und haben eine ausreichende Wahrnehmung der mit

dem Gebrauch des Geräts verbundenen Gefahren. Erlauben Sie Kindern nicht, mit dem Gerät zu spielen. Reinigungsund Wartungsarbeiten dürfen nicht von

unbewachten Kindern ausgeführt werden.

•ZUR BEACHTUNG: Lassen Sie keine Fette oder Öle unbewacht auf dem Herd stehen. Das ist gefährlich und kann einen Brand verursachen.

•NIEMALS eine Flamme/Brandherd mit Wasser löschen. Schalten Sie das Gerät aus und ersticken Sie die Flamme mit einem Deckel oder einer feuerfesten Decke.

•ZUR BEACHTUNG: Brandgefahr: Keine Gegenstände auf den Kochstellen liegen lassen.

•ZUR BEACHTUNG: Sollte die Glaskeramitoberfläche gesprungen sein, schalten Sie das Gerät aus, um so mögliche Stromschläge zu vermeiden.

•Verwenden Sie zur Reinigung des Kochfeldes keine Dampfoder Hochdruckreinigungsgeräte.

•Dieses Gerät kann nicht mit einem externen Timer oder einem getrennten Fernsteuerungssystem betrieben werden.

•ATTENZIONE: Questo apparecchio e le sue parti accessibili diventano molto caldi durante l’uso.

•Bisogna fare attenzione ed evitare di toccare gli elementi riscaldanti.

•Tenere lontani i bambini inferiori agli 8 anni se non continuamente sorvegliati.

•Il presente apparecchio puo’ essere utilizzato dai bambini a partire dagli 8 anni e da persone con ridotte capacita’ fisiche, sensoriali o mentali oppure con mancanza di esperienza e di conoscenza se si trovano sotto

adeguata sorveglianza oppure se sono stati istruiti circa l’uso dell’apparecchio in modo sicuro e se si rendono conto dei pericoli correlati. I bambini non devono giocare con l’apparecchio. Le operazioni di pulizia e di manutenzione non devono essere effettuate dai bambini senza sorveglianza.

•ATTENZIONE: Lasciare un fornello incustodito con grassi e olii puo’ essere pericoloso e puo’ provocare un incendio.

•Non bisogna MAI tentare di spegnere una fiamma/incendio con acqua, bense bisogna spegnere l’apparecchio e coprire la fiamma per esempio con un coperchio o con una coperta ignifuga

•ATTENZIONE: Rischio di incendio: non lasciare oggetti sulle superfici di cottura.

•ATTENZIONE: Se la superficie vetroceramica e’ incrinata, spegnere l’apparecchio per evitare la possibilit? di scossa elettrica.

•Non utilizzare mai pulitori a vapore o ad alta pressione per la pulizia dell’apparecchio.

•L’apparecchio non e’ destinato a essere messo in funzione per mezzo di un temporizzatore esterno oppure di un sistema di comando a distanza separato.

4

5 3

	4
GB	Description of the appliance
	Control panel

The control panel described in this manual is only a representative example: it may not exactly match the panelon your appliance.

1INCREASE POWER button switches on the hotplate and controls the power (see Start-up and use).

2REDUCE POWER button controls the power and switches off the hotplate (see Start-up and use).

3COOKING ZONE SELECTOR indicator shows a particular cooking zone has been selected and therefore various adjustments are possible.

4COOKING ZONE SELECTOR button is used to select the desired cooking zone.

5POWER indicator provides a visual display for the current heat level.

6ON/OFF button switches the appliance on and off.

7ON/OFF indicator light shows whether the appliance is on or off.

8PROGRAMME TIMER* button controls the cooking programme times (see Start-up and use).

9PROGRAMME TIMER* display shows which programme has been selected (see Start-up and use).

10COOKING ZONE PROGRAMMED* indicator lights show which cooking zones are being used during a cooking programme (see Start-up and use).

11CONTROL PANEL LOCK button prevents accidental changes to the hob settings (see Start-up

and use).

12CONTROL PANEL LOCK indicator light shows the control panel has been locked (see Start-up and use).

13TIMER* indicator light shows that the timer has been activated

! This product complies with the requirements of the latest European Directive on the limitation of power consumption of the standby mode.

If no operations are carried out for a period of 2 minutes, after the residual heat indicator lights turn off and the fan stops (if present), the appliance automatically switches to the .off mode..

The appliance resumes the operating mode once the ON/OFF button is pressed.

* Only available in certain models.

1	13	9	10	6
				7
				12
				GB
2		8		11
FR	Description de l’appareil
	Tableau de bord

Le tableau de bord qui est

décrit n.a qu.une valeur d.exemple :

il peut ne pas correspondre au modèle acheté.

1Touche AUGMENTATION DE PUISSANCE pour allumer le foyer et régler sa puissance (voir Mise en marche et utilisation).

2Touche DIMINUTION DE PUISSANCE pour régler la puissance et éteindre le foyer (voir Mise en marche et utilisation).

3Voyant FOYER SELECTIONNE pour signaler que le foyer correspondant a été sélectionné et que les régulations sont donc possibles.

4Touche SELECTION FOYER pour sélectionner le foyer souhaité

5Indicateur de PUISSANCE : une colonne lumineuse pour signaler le niveau de puissance atteint.

6Touche ON/OFF pour allumer ou éteindre l’appareil.

7Voyant ON/OFF : il signale si l’appareil est allumé ou éteint.

8Touche PROGRAMMATEUR* pour programmer la durée d’une cuisson (voir Mise en marche et Utilisation).

9Afficheur PROGRAMMATEUR* : pour afficher les choix correspondant à la programmation (voir Mise en marche et utilisation).

10Voyants FOYER PROGRAMMÉ* : ils indiquent les foyers quand une programmation est lancée (voir Mise en marche et utilisation).

11Touche VERROUILLAGE DES COMMANDES pour empêcher toute intervention extérieure sur les réglages de la table de cuisson (voir Mise en marche et Utilisation).

12Voyant COMMANDES VERROUILLEES : pour signaler le verrouillage des commandes (voir Mise en marche et Utilisation).

13Voyant MINUTEUR* il signale que le minuteur est activé

! Ce produit est conforme à la nouvelle Directive Européenne sur la réduction de la consommation d’énergie en mode standby. Sans opérations pendant 2 minutes, après

l’extinction des voyants de chaleur résiduelle et l’arrêt du ventilateur (si existants), l’appareil se place automatiquement en “off mode”. Pour remettre l’appareil en mode de fonctionnement

normal, appuyer sur la touche ON/OFF.

* N’existe que sur certains modèles

5

ES	Descripción del aparato
	Panel de control

El panel de control se describe a continuación a modo de ejemplo: puede no ser una exacta reproducción del modelo adquirido.

1Botón AUMENTO DE POTENCIA para encender la placa y regular la potencia (ver Puesta en funcionamiento y uso).

2Botón DISMINUCIÓN DE POTENCIA para regular la potencia y apagar la placa (ver Puesta en funcionamiento y uso).

3Piloto ZONA DE COCCIÓN SELECCIONADA indica que ha sido seleccionada dicha zona de cocción

y, por lo tanto, se pueden realizar las distintas regulaciones

4Botón SELECCIÓN DE ZONA DE COCCIÓN para seleccionar la zona de cocción deseada

5Indicador de POTENCIA: indica visualmente el nivel de calor alcanzado.

6Botón ON/OFF para encender y apagar el aparato.

7Piloto ON/OFF: indica si el aparato está encendido o apagado.

8Botón TEMPORIZADOR DE PROGRAMACIÓN* para programar la duración de una cocción (ver Puesta en funcionamiento y uso).

9Display TEMPORIZADOR DE PROGRAMACIÓN*: visualiza las selecciones correspondientes a la programación (ver Puesta en funcionamiento y uso).

10Pilotos ZONA DE COCCIÓN PROGRAMADA*: indican las zonas de cocción cuando comienza una programación (ver Puesta en funcionamiento y uso).

11Botón BLOQUEO DE MANDOS para impedir modificaciones fortuitas a las regulaciones de la encimera (ver Puesta en funcionamiento y uso).

12Piloto MANDOS BLOQUEADOS: indica que se ha producido el bloqueo de los mandos (ver Puesta en

funcionamiento y uso).

13Piloto CONTADOR DE MINUTOS* indica que se ha activado el contador de minutos

! Este producto satisface los requisitos establecidos por la nueva Directiva europea sobre la limitación de los consumos energéticos en standby.

Si no se realizan operaciones por 2 minutos, una vez que se apagan los luces piloto del calor residual y del ventilador (si están presentes), el aparato se coloca de forma automática en el modo .off mode.. El aparato vuelve al modo operativo utilizando la

tecla ON/OFF.

PT	Descrição do aparelho
	Painel de comandos

O painel de comandos descrito a seguir está representado para fins explicativos: pode não ser uma exacta

reprodução do modelo comprado.

1Botão AUMENTO POTÊNCIA para ligar a chapa e regular a potência (veja Início e utilização).

2Botão DIMINUIÇÃO POTÊNCIA para regular a potência e desligar a chapa (veja Início e utilização).

3Indicador luminoso ZONA DE COZEDURA SELECCIONADA indica que a zona de cozedura relativa foi seleccionada e são portanto possíveis as várias regulações.

4Botão SELECÇÃO ZONA DE COZEDURA para seleccionar a zona de cozedura desejada.

5Indicador POTÊNCIA sinaliza visualmente o nível de calor alcançado.

6Botão ON/OFF para ligar e desligar o aparelho.

7Indicador ON/OFF: sinaliza se o aparelho está aceso ou apagado.

8Botão TIMER DE PROGRAMAÇÃO para regular a programação da duração de uma cozedura (veja Início e utilização).

9Display TIMER DE PROGRAMAÇÃO: visualiza as escolhas relativas à programação (veja Início e utilização).

10Indicadores luminosos ZONA DE COZEDURA PROGRAMADA: indicam as zonas de cozedura quando se inicia uma programação (veja Início e

utilização).

11Botão BLOQUEIO DOS COMANDOS para impedir modificações acidentais das regulações do plano de cozedura (veja Início e utilização).

12Indicador luminoso COMANDOS BLOQUEADOS: sinaliza o bloqueio dos comandos (veja Início e

utilização).

13Indicador luminoso CONTADOR DE MUNITOS* indica que está activo o contador de minutos.

! Este produto satisfaz os requisitos impostos pela nova Directiva Europeia sobre a limitação dos consumos energéticos em stand-by.

Se não se efectuarem operações por 2 minutos, depois que os indicadores de calor resíduo e da ventoinha (se presentes) se desligarem, o aparelho coloca-se automaticamente na modalidade .off mode..

O aparelho voltará para a modalidade operativa ao carregar na tecla ON/OFF.

* Presente sólo en algunos modelos.

* Há somente em alguns modelos.

6

DE Beschreibung des Gerätes

Bedienfeld

Das hier beschriebene Bedienfeld dient nur als Beispiel, es handelt sich nicht unbedingt um eine genaue

Widergabe des von Ihnen erworbenen Modells.

1Taste ERHÖHEN DER LEISTUNG: Zum Einschalten sowie zur Leistungsregelung der Kochzone (siehe Inbetriebsetzung und Gebrauch).

2Taste HERABSETZEN DER LEISTUNG: Zur Leistungsregelung sowie zum Ausschalten der Kochzone (siehe Inbetriebsetzung und Gebrauch).

3Kontrollleuchte GEWÄHLTE KOCHZONE: Diese zeigt an, dass die der Kontrollleuchte entsprechende Kochzone gewählt wurde und die gewünschten Einstellungen demnach vorgenommen werden können.

4Taste WAHL DER KOCHZONE: Mittels dieser wird die gewünschte Kochzone gewählt.

5LEISTUNGSANZEIGE: Auf dieser ist der jeweils erreichte Heizwert ersichtlich.

6Taste ON/OFF: Zum Einbzw. Ausschalten des Gerätes.

7Kontrollleuchte ON/OFF: Diese zeigt an, ob das Gerät einoder ausgeschaltet ist.

8Taste PROGRAMMIERUNGSTIMER*: Mittels dieser Taste kann die für jede Kochzone jeweils programmierte Zeit reguliert werden (siehe Inbetriebsetzung und Gebrauch).

9Display PROGRAMMIERUNGSTIMER*: Auf diesem Display werden die jeweils programmierten Zeiten angezeigt (siehe Inbetriebsetzung und Gebrauch).

10Kontrollleuchten PROGRAMMIERTE KOCHZONE*: Diese zeigen die Kochzonen an, die programmiert wurden (siehe Inbetriebsetzung und Gebrauch).

11Taste SPERRE DER SCHALTELEMENTE: Um versehentliche Änderungen der am Kochfeld erfolgten Einstellungen zu verhindern (siehe Inbetriebsetzung und Gebrauch).

12Kontrollleuchte SCHALTELEMENTE GESPERRT: Diese signalisiert, dass die Schaltelemente gesperrt wurden (siehe Inbetriebsetzung und Gebrauch).

13Kontrollleuchte KURZZEITWECKER*: Diese signalisiert, dass der Kurzzeitwecker läuft

! Dieses Produkt entspricht den Vorschriften der neuen Europäischen Richtlinie zur Einschränkung des

Energieverbrauchs im Standby. Werden für 2 Minuten keine Tasten gedrückt, dann stellt sich das Gerät nach Ausschalten der Anzeigen für Resthitze und des Lüfters (wenn vorhanden) automatisch in den “off mode”. Das Gerät kehrt durch Drücken der Taste ON/OFF in den Betriebsmodus zurück.

* Nur bei einigen Modellen.

IT	Descrizione dell’apparecchio
	Pannello di controllo
Il pannello di controllo che qui viene descritto è
rappresentato a fini esemplificativi: può non essere una
esatta riproduzione del modello acquistato.
1 Tasto AUMENTO POTENZA per accendere la		GB
piastra e regolare la potenza (vedi Avvio e utilizzo).

2Tasto DIMINUZIONE POTENZA per regolare la potenza e spegnere la piastra (vedi Avvio e utilizzo).

3Spia ZONA DI COTTURA SELEZIONATA indica che la zona di cottura relativa è stata selezionata e quindi sono possibili le varie regolazioni

4Tasto SELEZIONE ZONA DI COTTURA per selezionare la zona di cottura desiderata

5Indicatore POTENZA: segnala visivamente il livello di calore raggiunto.

6Tasto ON/OFF per accendere e spegnere l’apparecchio.

7Spia ON/OFF: segnala se l’apparecchio è acceso o spento.

8Tasto TIMER DI PROGRAMMAZIONE* per regolare la programmazione della durata di una cottura (vedi Avvio e utilizzo).

9Display TIMER DI PROGRAMMAZIONE*: visualizza le scelte relative alla programmazione (vedi Avvio e

utilizzo).

10Spie ZONA DI COTTURA PROGRAMMATA*: indicano le zone di cottura quando si avvia una programmazione (vedi Avvio e utilizzo).

11Tasto BLOCCO DEI COMANDI per impedire modifiche fortuite alle regolazioni del piano cottura

(vedi Avvio e utilizzo).

12Spia COMANDI BLOCCATI: segnala l’avvenuto blocco dei comandi (vedi Avvio e utilizzo).

13Spia CONTAMINUTI* indica che è attivo il contaminuti

! Questo prodotto soddisfa i requisiti imposti dalla nuova Direttiva Europea sulla limitazione dei consumi energetici in standby.

Se non si eseguono operazioni per 2 minuti, dopo lo spegnimento delle spie di calore residuo e della ventola (ove presenti), l’apparecchio si dispone automaticamente in modalità “off mode”.

L’apparecchio ritorna in modalità operativa agendo sul tasto ON/OFF.

* Presente solo in alcuni modelli.

7

Installation

		! Before operating your new appliance please read
	GB
		this instruction booklet carefully. It contains important
		information concerning the safe operation, installation
		and maintenance of the appliance.
		! Please keep these operating instructions for future
		reference. Pass them on to any new owners of the
		appliance.

Positioning

! Keep all packaging material out of the reach of children. It may present a choking or suffocation hazard (see Precautions and tips).

! The appliance must be installed by a qualified professional in accordance with the instructions provided. Incorrect installation may cause harm to people and animals or may damage property.

Built-in appliance

Use a suitable cabinet to ensure that the appliance functions properly.

•The supporting surface must be heat-resistant up to a temperature of approximately 100°C.

•If the appliance is to be installed above an oven, the oven must be equipped with a forced ventilation cooling system.

•Avoid installing the hob above a dishwasher: if this cannot be avoided, place a waterproof separation device between the two appliances.

•Depending on the hob you want to install, the cabinet must have the following dimensions (see figure):

			590									574
48					48				48				504
				520
													1
													-
				-				1	560			490	+/
								+/
				1	560 +/			-		+/-
560	+/-		490	+/			490				1
		1			-	1

Ventilation

To allow adequate ventilation and to avoid overheating of the surrounding surfaces the hob should be positioned as follows:

•At a minimum distance of 40 mm from the back panel.

•So that a minimum distance of 20 mm is maintained between the installation cavity and the cabinet underneath.

•Kitchen cabinets adjacent to the appliance and taller than the top of the hob must be at least 600 mm from the edge of the hob.

min. 20 mm

mm5 COMPARTMENT

min. 40 mm

min. 20 mm

5 mm

FAN-ASSISTED

OVEN

min. 40 mm

FRONT SIDE

OF HOB

SUPPORTING
SURFACE	30
		40

UNDERSIDE

OF HOB

8

UNDERSIDE OF HOB

Fixing

The appliance must be installed on a perfectly level supporting surface.

Any deformities caused by improper fixing could affect the features and operation of the hob.

The thickness of the supporting surface should be taken into account when choosing the length of the screws for the fixing hooks:

•30 mm thick: 17.5 mm screws

•40 mm thick: 7.5 mm screws

Fix the hob as follows:

1.Use short flat-bottomed screws to fix the 4 alignment springs in the holes provided at the central point of each side of the hob.

2.Place the hob in the cavity, make sure it is in a central position and push down on the whole perimeter until the hob is stuck to the supporting surface.

3.For hobs with raised sides: After inserting the hob into its cavity, insert the 4 fixing hooks (each has its own pin) into the lower edges of the hob, using the long pointed screws to fix them in place, until the glass is stuck to the supporting surface.

!The screws for the alignment springs must remain accessible.

!In order to adhere to safety standards, the appliance must not come into contact with electrical parts once it has been installed.

!All parts which ensure the safe operation of the appliance must not be removable without the aid of a tool.

Electrical connection

! The electrical connection for the hob and for any builtin oven must be carried out separately, both for safety purposes and to make extracting the oven easier.

Terminal board

On the lower part of the appliance there is a connection box for the different types of electricity

supply (the picture is only an indication and is not an exact representation of the

purchased model).

Single-phase connection

The hob is equipped with a pre-connected electricity supply cable, which is designed for single-phase

	connection. Connect the wires in accordance with the
								GB
	instructions given in the following table and diagrams:
	Voltage and		Electrical cable		Wire connection
	mains frequency
	230-240V 1+N ~				: yellow/green
					N: the two blue wires together
	220-240V 1+N ~
					L: brown and black together
	50/60 Hz

Other types of connection

If the mains supply corresponds with one of the following:

Voltage and mains frequency

•400V - 2+N ~ 50/60 Hz

•220-240V 3 ~ 50/60 Hz

•230-240V 3 ~ 50/60 Hz

•400V - 2+2N ~ 50/60 Hz

Separate the wires and connect them in accordance with the instructions given in the following table and diagrams:

	Voltage and	Electrical cable	Wire connection
	mains frequency
	400V - 2+N ~		: yellow/green;
	50/60 Hz		N: the two blue wires
	230-240V 3 ~		together
	220-240V 3 ~		L1: black
	50/60 Hz		L2: brown
			: yellow/green;
	400V - 2+2N ~		N1: blue
	50/60 Hz		N2: blue
			L1: black
			L2: brown

If the mains supply corresponds with one of the following:

Voltage and mains frequency

• 400V 3 - N ~ 50/60 Hz proceed as follows:

! The cable provided is not suitable for the following types of installation.

1.Use a suitable supply cable, H05RR-F or higher, with the right dimensions (cable cross section: 25 mm).

2.To open the terminal board, use a screwdriver as

a lever under the side tabs of the cover (see Terminal board picture).

3.Loosen the cable clamp screw and the terminal board screws in accordance with the type of connection required and position the connection supports as shown in the following table and diagrams.

4.Position the wires in accordance with the information given in the following table and diagrams and connect the appliance by tightening all the screws for the springs as much as possible.

9

		Voltage and	Electrical connections	Terminal board
GB
		mains frequency
		400V 3-N ~		Three-phase 400
		50/60 Hz
		5. Secure the power supply cable by fastening the
		cable clamp screw, then put the cover back on.
		Phase Phase Phase

				Three-phase 400
	1	2	3
		5	4
				Connecting the
				electricity supply
Earth	Neutral	U-bolt		cable to the
		connection support
				mains

If the appliance is being connected directly to the electricity mains an omnipolar switch must be installed with a minimum opening of 3 mm between contacts.

! The installer must ensure that the correct electrical connection has been made and that it is fully compliant with safety regulations.

Before connecting the appliance to the power supply, make sure that:

•The appliance is earthed and the plug is compliant with the law.

•The socket can withstand the maximum power of the appliance, which is indicated on the data plate located on the appliance itself.

•The voltage falls within the range of values indicated on the data plate.

•The socket is compatible with the plug of the appliance. If the socket is incompatible with the plug, ask an authorised technician to replace it. Do not use extension cords or multiple sockets.

!Once the appliance has been installed, the power supply cable and the electrical socket must be easily accessible.

!The cable must not be bent or compressed.

!The cable must be checked regularly and replaced by authorised technicians only.

!The manufacturer declines any liability should these safety measures not be observed.

!Do not remove or replace the power supply cable for any reason. Its removal or replacement will void the warranty and the CE marking. INDESIT does not

assume liability for accidents or damage arising from

replacement/removal of the original power supply cable. Replacement can only be accepted when carried out by personnel authorised by INDESIT and using an original spare part.

10

Extendable cooking zones	GB

Certain models are fitted with extendable cooking zones. These may be circular or oval and may vary in their extensibility (they may be double or triple hotplates). A list of controls is given below (these controls are only present in models with the extendable cooking zone option).

Circular extendable hotplate

Oval extendable hotplate

DOUBLE

TRIPLE

OVAL

HOTPLATE ON

HOTPLATE ON

HOTPLATE ON

indicator light

indicator light

indicator light

DOUBLE	TRIPLE	OVAL
HOTPLATE ON	HOTPLATE ON	PLATE ON
button	button	button

•DOUBLE HOTPLATE ON button switches on the double hotplate (see Start-up and use).

•DOUBLE HOTPLATE ON indicator light shows the double hotplate has been switched on.

•TRIPLE HOTPLATE ON button switches on the triple hotplate (see Start-up and use).

•TRIPLE HOTPLATE ON indicator light shows the triple hotplate has been switched on.

•OVAL HOTPLATE ON button switches on the oval hotplate (see Start-up and use).

•OVAL HOTPLATE ON indicator light shows the oval hotplate has been switched on.

11

Start-up and use

		! The glue applied on the gaskets leaves traces of
	GB
		grease on the glass. Before using the appliance, we
		recommend you remove these with a special non-
		abrasive cleaning product. During the first few hours
		of use there may be a smell of rubber which will
		disappear very quickly.
		! A few seconds after the hob is connected to the
		electricity supply, a buzzer will sound. The hob may
		now be switched on.
		! If the -or +button is pressed for an extended
		period of time, the display scrolls quickly though the
		power levels and timer minutes.
		Switching on the hob
		To switch the hob on, press and hold the		button
		for approximately one second.

Switching on the cooking zones

Each cooking zone is controlled using a selector button and a power adjustment device consisting of a

double -and +button.

•To begin operating a cooking zone, press the

corresponding control button and set the desired power level (between 0 and 9) using the buttons - and +.

Power function

The power function for the cooking zones may be used to shorten heating-up times. Activate and set the power

level for the desired cooking zone as described in the previous paragraph. Press and hold the selector

button corresponding to the desired cooking zone for at least 2 seconds. The display, the power level indicator, will alternately show the letter “P” and the power level set previously until the desired power level has been reached. Once this level has been reached, the display will revert to showing the set power level. To deactivate this function, press and hold – for at least 2 seconds - the selector button corresponding to

the cooking zone on which thefunction has been activated; alternatively, select a different power level

using the buttons -and +.

Switching off the cooking zones

To switch off a cooking zone, select it using the

corresponding selector button and:

• Press the -button: the power of the cooking zone will progressively decrease until it is switched off.

Heating elements

Two types of heating element may be installed, depending on the appliance model: halogen and radiant elements.

Halogen elements emit heat via radiation from the halogen lamps they contain.

They have similar properties to gas burners: they are easy to control and reach set temperatures quickly, allowing you to see the power level instantly. Radiant elements consist of a series of coils which allow heat to be distributed evenly at the base of the cookware, so that all slow-flame cooking may be

performed successfully, for example stews, sauces or reheated dishes.

Programming the cooking duration

! All the cooking zones may be programmed simultaneously, for a duration between 1 and 99 minutes.

1.Select the cooking zone using the corresponding selector button.

2.Adjust the power level of the cooking zone.

3.Press the programming button. The indicator light corresponding to the selected zone will start flashing.

4.Set the cooking duration using the -and + buttons.

5.Confirm by pressing the button or automatic selection occurs after 10 seconds.

The timer begins counting down immediately. A buzzer sounds for approximately 1 minute and the cooking zone switches off when the set programme has finished. Repeat the above procedure for each hotplate you wish to programme.

Using multiple programmes and the display

If one or more hotplates are programmed, the display will show the data for the hotplate with the least time remaining, and the light corresponding to the position of the hotplate will flash.

The lights corresponding to the other hotplates

12

indicator light is illuminated

programmed will be switched on.

To visualise the time remaining for the other programmed

hotplates, press the button repeatedly: the time remaining for each hotplate will be shown sequentially in a clockwise order, starting from the

front left hotplate.

Changing the programme

1.Press the button repeatedly until the duration you wish to change is shown.

2.Use the buttons to set the new duration.

3.Confirm by pressing the button.

To cancel a programme, follow the above instructions.

At step 2, press the -button: the duration decreases progressively until it reaches 0 and switches off. The programme resets and the display exits programming mode.

Timer

The hob must be switched on.

The timer can be used to set a duration up to 99 minutes.

1. Press the programming button until the timer

.

2. Set the desired duration using the -and +buttons.

3. Confirm by pressing the button.

The timer begins counting down immediately. When the time has elapsed, a buzzer will sound (for one minute).

Control panel lock

When the hob is switched on, it is possible to lock the oven controls in order to avoid accidental changes being made to the settings (by children, during

cleaning, etc.). Press the button to lock the control panel: the indicator light above the button will switch on.

To use any of the controls (e.g. to stop cooking), you

must switch off this function. Press the button for a few moments, the indicator light will switch off and the lock function will be removed.

Switching off the hob

Press the button to switch the appliance off. GB If the control panel lock has been activated, the

controls will continue to be locked even after the hob is switched on again. In order to switch the hob on again, you must first remove the lock function.

“Demo” mode

It is possible to set the hob to a demonstration mode where all the controls work normally but the heating elements do not switch on. To activate the “demo” mode the hob must be switched on, with all the hotplates switched off.

•Press and hold the +and -buttons simultaneously for 6 seconds. When the 6 seconds have elapsed, the ON/OFF and CONTROLS

LOCKED indicator lights will flash for one second. Release the +and -buttons and press the button;

•The display will show the text DE and MO and the hob will be switched off.

•When the hob is switched on again it will be set to the “demo” mode.

To exit this mode, follow the procedure described above. The display will show the text DE and OF and the hob will be switched off. When it is next switched on, the hob will function normally.

Practical advice on using the appliance

To obtain the best results from your hob:

•Use pans with a thick, flat base in order to fully utilise the cooking zone.

•Always use pans with a diameter which is large enough to cover the hotplate fully, in order to use all the available heat.

•Make sure that the base of the cookware is always clean and dry, in order to fully utilise and extend the life of both the cooking zones and the cookware.

•Avoid using the same cookware which has been used on gas burners: the heat concentration on gas burners may distort the base of the pan, causing it not to adhere correctly.

13

GB	Safety devices
	Residual heat indicators
	Each cooking zone is equipped with a residual heat
	indicator. This indicator signals which cooking zones
	are still at a high temperature. If the power display
				, the cooking zone is still hot. It is possible,
	shows
	for example, to keep a dish warm or melt butter or
	chocolate. As the cooking zone cools, the power
							. The display switches off when the
	display will show
	cooking zone has cooled sufficiently.
	Overheating protection
	If the electronic elements overheat, the hob switches
	off automatically and F appears on the display,
	followed by a flashing number. When the temperature
	has reached a suitable level, this message disappears
	and the hob may be used again.
	Safety switch
	The appliance has a safety switch which automatically
	switches the cooking zones off after they have been
	in operation for a certain amount of time at a particular
	power level. When the safety switch has been
	triggered, the display shows “0”.

For example: the right rear hotplate is set to 5 and will switch off after 5 hours of continuous operation, while the front left hotplate is set to 2 and will switch off after 8 hours.

Power level	Maximum operating time in hours
1	9
2	8
3	7
4	6
5	5
6	4
7	3
8	2
9	1

Buzzer

This can also indicate several irregularities:

•An object (a pan, cutlery, etc.) has been placed on the control panel for more than 10 seconds.

•Something has been spilt on the control panel.

•A button has been pressed for too long. All of the above situations may cause the buzzer to sound. Remove the cause of the malfunction to stop the buzzer. If the cause of the problem is not removed, the buzzer will keep sounding and the hob will switch off.

14

Practical cooking advice	GB

Very high-flame	cooking
High-flame	cooking

Medium-flame cooking

Low-flame cooking

Very low-flame cooking

ª
	Pressure cooking	Frying
	Pressure cooker
•	Grilling	Boiling
•
¶	Crêpes	Cooking on a high flame and browning
		(roasts, steaks, escalopes, fish fillets,
		fried eggs)

¶

Fast thickening (liquid juices)

§Boiling water (pasta, rice, vegetables) Milk

§
S	Slow thickening (dense juices)
S
¢	Bain-marie cooking	Pressure cooking after whistle
¢
£	Low-flame cooking (stews)	Reheating dishes
™
™
¡	Chocolate sauce	Keeping food hot

15

Precautions and tips

		! This appliance has been designed and manufactured
	GB
		in compliance with international safety standards. The
		following warnings are provided for safety reasons and
		must be read carefully.
		This appliance conforms to the following
		European Economic Community directives:
		- 2006/95/EEC dated 12/12/06 (Low Voltage) and
		subsequent amendments;
		- 2004/108/EEC dated 15/12/04 (Electromagnetic
		Compatibility) and subsequent amendments;
		- 93/68/EEC dated 22/07/93 and subsequent
		amendments.
		- 1275/2008 stand-by/off mode.
		General safety

! Make sure that the air inlet behind the fan grille is never obstructed. The built-in hob should, in fact, be provided with suitable ventilation for the cooling of the electronic components used in the appliance.

•The appliance was designed for domestic use inside the home and is not intended for commercial or industrial use.

•The appliance must not be installed outdoors, even in covered areas. It is extremely dangerous to leave the appliance exposed to rain and storms.

•Do not touch the appliance when barefoot or with wet or damp hands and feet.

•The appliance must be used by adults only for the preparation of food, in accordance with the

instructions provided in this booklet. Do not use the hob as a worktop or chopping board.

•The glass ceramic hob is resistant to mechanical shocks, but it may crack (or even break) if hit with a sharp object such as a tool. If this happens, disconnect the appliance from the electricity mains immediately and contact a Service Centre.

•Ensure that power supply cables of other electrical appliances do not come into contact with the hot parts of the hob.

•Remember that the cooking zones remain relatively hot for at least thirty minutes after they have been switched off. An indicator light provides a warning when residual heat is present (see Start-up and use).

•Keep any object which could melt away from the hob, for example plastic and aluminium objects, or products with a high sugar content. Be especially careful when using plastic film and aluminium foil or packaging: if placed on surfaces which are still hot, they may cause serious damage to the hob.

•Always make sure that pan handles are turned towards the centre of the hob in order to avoid accidental burns.

•When unplugging the appliance, always pull the plug from the mains socket; do not pull on the cable.

•Never perform any cleaning or maintenance work without having disconnected the appliance from the electricity mains.

•The appliance should not be operated by people (including children) with reduced physical, sensory or mental capacities, by inexperienced individuals or by anyone who is not familiar with the product. These individuals should, at the very least, be supervised by someone who assumes responsibility for their safety or receive preliminary instructions relating to the operation of the appliance.

•Do not look at the halogen lamps in the cooking zones for long if they are present.

•Do not let children play with the appliance.

•Do not place metal objects (knives, spoons, pan lids, etc.) on the hob as they may become hot..

•The appliance is not intended to be operated by means of an external timer or separate remotecontrol system.

Disposal

•When disposing of packaging material: observe local legislation so that the packaging may be reused.

•The European Directive 2002/96/EC relating to Waste Electrical and Electronic Equipment

(WEEE) states that household appliances should not be disposed of using the normal solid urban waste cycle. Exhausted appliances should be collected separately in order to optimise the cost of re-using and recycling the materials inside the machine, while preventing potential damage to the atmosphere and to public health. The crossed-out dustbin is marked on all products to remind the owner of their obligations regarding separated waste collection.

For further information relating to the correct disposal of exhausted household appliances, owners may contact the public service provided or their local dealer.

16

Care and maintenance

Switching the appliance off

Disconnect your appliance from the electricity supply before carrying out any work on it.

Cleaning the appliance

!Do not use abrasive or corrosive detergents (for example, products in spray cans for cleaning barbecues and ovens), stain removers, anti-rust

products, powder detergents or sponges with abrasive surfaces: these may scratch the surface beyond repair.

!Never use steam cleaners or pressure cleaners on the appliance.

•It is usually sufficient simply to wash the hob using a damp sponge and dry it with absorbent kitchen towel.

•If the hob is particularly dirty, rub it with a special glass ceramic cleaning product, then rinse well and dry thoroughly.

•To remove more stubborn dirt, use a suitable scraper. Remove spills as soon as possible, without waiting for the appliance to cool, to avoid residues forming crusty deposits. You can achieve excellent results by using a rust-proof steel wire sponge - specifically designed for glass ceramic surfaces - soaked in soapy water.

•If any plastic or sugary substances are accidentally melted on the hob, remove them immediately with the scraper, while the surface is still hot.

•Once it is clean, the hob may be treated with a special protective maintenance product: the

invisible film left by this product protects the surface from drips during cooking. This maintenance task should be carried out while the appliance is warm (not hot) or cold.

•Always remember to rinse the appliance well with clean water and dry it thoroughly: residues can become encrusted during subsequent cooking processes.

Stainless steel frame (only in models with outer frame)

Stainless steel can be marked by hard water which has	GB
been left on the surface for a long time, or by cleaning
products containing phosphorus.
After cleaning, it is advisable to rinse the surface well
and dry it thoroughly. If water is spilt on the surface,
dry it quickly and thoroughly.
! Some hobs have an aluminium frame which is
similar to stainless steel. Do not use any cleaning or
degreasing products which are not suitable for use
with aluminium.

Disassembling the hob

If it is necessary to disassemble the hob:

1.Loosen the screws fixing the alignment springs on each side.

2.Loosen the screws holding the fixing hooks in each corner.

3.Take the hob out of its installation cavity.

! Do not attempt to repair the appliance yourself. If the appliance breaks down, contact a Service Centre.

17

Technical description of the models

This table provides a model-by-model list of the energy absorption values, type of heating elements and diameters GB of each cooking zone.

Hobs	KRA 640 X S
	KRA 640 B S			KRC 641 D X
	KRA 640 C (PL) S			KRC 641 D B
	KRC 640 B			KRC 741 D Z
	KRC 640 X
Cooking zone	Power (W)		Diameter (mm)	Power (W)		Diameter (mm)
Back Left	H 2300		210	HD 2200/1000		210/140
Back Right	H 1400		160	H 1400		160
Front Left	H 1200		145	H 1200		145
Front Right	H 1800		180	H 1800		180
Total power	6700			6600
Hobs	KRA 631 T C S			Key:
				H = single hilight
	KRC 631 T X
				HO = oval hilight
	KRC 631 T B
				HD = double hilight
Cooking zone	Power (W)		Diameter (mm)
				HT = triple hilight
Back Right	H 1400		160	A = single halogen
Centre Left	HT 2700/1950/1050		270/210/145	AD = double halogen
Front Right	H 1800		180
Total power	5900

18

Installation

!Conserver ce mode d’emploi pour pouvoir le consulter à tout moment. En cas de vente, de cession ou de déménagement, veiller à ce qu’il suive l’appareil pour informer le nouveau propriétaire sur son fonctionnement et lui fournir les conseils correspondants.

!Lire attentivement les instructions : elles contiennent des conseils importants sur l’installation, l’utilisation et la sécurité de cet appareil.

Positionnement

! Les emballages ne sont pas des jouets pour enfants, il faut les mettre au rebut en respectant la réglementation sur le tri sélectif des déchets (voir

Précautions et conseils).

! L’installation doit être effectuée par un professionnel du secteur conformément aux instructions du fabricant. Une mauvaise installation peut causer des dommages à des personnes, des animaux ou des biens.

Encastrement

Pour garantir le bon fonctionnement de l’appareil, il faut que le meuble possède des caractéristiques bien précises :

•le matériau du plan d’appui doit pouvoir résister à une température d’environ 100°C;

•en cas d’installation de la table de cuisson audessus d’un four, il faut que ce dernier soit équipé d’un dispositif de refroidissement par ventilation forcée ;

•éviter d’installer la table de cuisson au-dessus d’un lave-vaisselle : si c’est le cas, prévoir une séparation étanche entre les deux appareils ;

•selon la table de cuisson à installer (voir figures), la découpe du meuble doit avoir les dimensions suivantes :

			590				690				574
48					48				48
				520				520				504
				1				1				1
				-				-				-
560			490	+/	560 +/		490	+/	560 +/		490	+/
	+/-
		1			-	1			-	1

Aération

Pour permettre une bonne aération et pour éviter toute surchauffe des surfaces autour de l’appareil, la table de cuisson doit être positionnée :

•à au moins 40 mm de distance du mur arrière;

•de manière à ce qu’il reste au moins 20 mm de distance entre la découpe d’encastrement et le meuble en dessous.

•Les meubles jouxtant la table, dont la hauteur

FR

min. 20 mm mm5 TIROIR

min. 40 mm

min. 20 mm

5 mm

CHALEUR

TOURNANTE

min. 40 mm

CÔTÉ AVANT DE LA

TABLE DE CUISSON

PLAN DE
TRAVAIL	30	40

TABLE DE CUISSON

RETOURNÉE

19

RETOURNEE

TABLE DE CUISSON

		dépasse celle du plan de cuisson, doivent être
	FR
		placés à au moins 600 mm du bord du plan.
		Fixation
		Il est impératif d’assurer l’encastrement de l’appareil sur
		un plan d’appui parfaitement plat.
		Les déformations provoquées par une mauvaise
		fixation risquent d’altérer les caractéristiques de la
		table de cuisson ainsi que ses performances.
		La longueur de la vis de réglage des crochets de
		fixation doit être réglée avant leur montage selon
		l’épaisseur du plan d’appui :
		• épaisseur 30 mm : vis 17,5 mm;
		• épaisseur 40 mm : vis 7,5 mm

Pour sa fixation, procéder comme suit :

1.Se servir des vis courtes sans pointe pour visser les 4 ressorts de centrage dans les trous prévus sur chaque côté de la table, en leur milieu;

2.insérer la table de cuisson dans la découpe prévue, bien au centre et bien appuyer tout autour du cadre pour que la table adhère parfaitement au plan d’appui.

3.pour les tables avec profils latéraux : après avoir encastré la table de cuisson dans la découpe, insérer les 4 crochets de fixation (chacun avec son goujon) sur le périmètre inférieur de la table de cuisson et visser avec les vis longues à pointe jusqu’à ce que le verre adhère bien au plan d’appui.

!Il faut absolument que les vis des ressorts de centrage soient accessibles.

!Conformément aux normes de sécurité, après encastrement de l’appareil, il ne doit plus y avoir possibilité de contact avec les parties électrifiées.

!Toutes les parties qui servent de protection doivent être fixées de manière à ne pouvoir être enlevées qu’avec l’aide d’un outil.

Raccordement électrique

! Le branchement électrique de la table de cuisson et celui d’un éventuel four à encastrer doivent être effectués séparément, pour des raisons de sécurité électrique et pour pouvoir démonter plus facilement le four en cas de besoin.

Bornier

L’appareil est équipé, sur le dessous, d’un boîtier

de raccordement à plusieurs types d’alimentation électrique (la figure n’est qu’indicative, elle peut ne

pas correspondre au modèle acheté).

Raccordement monophasé

La table est fournie déjà équipée d’un cordon d’alimentation prévu pour raccordement monophasé. Procéder au raccordement des fils en suivant les indications du tableau et des dessins suivants :

	Tension type et	Cordon électrique	Raccordement fils
	fréquence réseau
	230-240V 1+N ~		: jaune/vert;
			N: les 2 fils bleus ensemble
	220-240V 1+N ~
			L: le marron avec le noir
	50/60 Hz

Autres types de branchement

Si l’installation électrique correspond à une des caractéristiques suivantes :

Tension type et fréquence réseau

•400V - 2+N ~ 50/60 Hz

•220-240V 3 ~ 50/60 Hz

•230-240V 3 ~ 50/60 Hz

•400V - 2+2N ~ 50/60 Hz

Séparer les câbles et procéder au raccordement des fils en suivant les indications du tableau et des dessins suivants :

	Tension type et	Cordon électrique	Raccordement fils
	fréquence réseau
	400V - 2+N ~		: jaune/vert;
	50/60 Hz
			N: les 2 fils bleus
	230-240V 3 ~		ensemble
	220-240V 3 ~
			L1: noir
	50/60 Hz
			L2: marron
			: jaune/vert;
	400V - 2+2N ~		N1: bleu
	50/60 Hz		N2: bleu
			L1: noir
			L2: marron

Si l’installation électrique correspond à une des caractéristiques suivantes :

Tension type et fréquence réseau

• 400V 3 - N ~ 50/60 Hz procéder comme suit :

! Le câble éventuellement fourni n’est pas prévu pour ces types d’installation.

1.Utiliser un câble d’alimentation approprié, type H05RR-F ou supérieur, aux dimensions adéquates (section câble : 25 mm).

2.Faire levier à l’aide d’un tournevis sur les languettes du couvercle du bornier pour l’ouvrir (voir figure

Bornier).

20

3.Dévisser la vis du serre-câble et les vis des bornes correspondant au type de raccordement nécessaire et positionner les cavaliers de raccordement conformément aux indications du tableau et des figures ci-dessous.

4.Positionner les fils conformément aux indications du tableau et des figures ci-dessous et procéder au raccordement en serrant à fond toutes les vis des bornes.

5.Fixer le câble d’alimentation dans le serre-câble correspondant et fermer le couvercle.

Triphasé 400

Phase Phase Phase

	1	2	3
		5	4
Terre	Neutre	Cavalier

Branchement du câble d’alimentation au réseau électrique

En cas de raccordement

direct au réseau, il faut intercaler entre l’appareil et le

réseau un interrupteur à coupure omnipolaire ayant au FR moins 3 mm d’écartement entre les contacts.

! L’installateur est responsable du bon raccordement électrique de l’appareil et du respect des normes de sécurité.

Avant de procéder au branchement, s’assurer que :

•la prise est bien munie d’une terre conforme à la loi;

•la prise est bien apte à supporter la puissance maximale de l’appareil, indiquée sur la plaque signalétique de l’appareil ;

•la tension d’alimentation est bien comprise entre les valeurs indiquées sur la plaque signalétique;

•la prise est bien compatible avec la fiche de l’appareil. Si ce n’est pas le cas, remplacer la prise ou la fiche, ne pas utiliser de rallonges ni de prises multiples.

!Après installation de l’appareil, le câble électrique et la prise de courant doivent être facilement accessibles

!Le câble ne doit être ni plié ni excessivement écrasé.

!Le câble doit être contrôlé périodiquement et ne peut être remplacé que par un technicien agréé.

!Nous déclinons toute responsabilité en cas de non respect des normes énumérées ci-dessus.

!Ne retirer ou ne remplacer en aucun cas le câble d’alimentation. Toute opération d’enlèvement ou de remplacement annule automatiquement la garantie et la marque CE INDESIT décline toute responsabilité en cas d’accidents ou de dommages dérivants

de l’enlèvement ou du remplacement du câble d’alimentation original. Seul le remplacement effectué par un technicien agréé INDESIT utilisant une pièce détachée originale est autorisé.

21

Foyers extensibles

FR

Certains modèles sont équipés de foyers extensibles. Ces derniers peuvent avoir soit une forme circulaire soit une

forme ovale et s’étendre pour former des foyers doubles ou triples. Illustration des commandes présentes sur les

modèles équipés de ces options.

Foyer extensible circulaire

Foyer extensible ovale

Voyant

Voyant

Voyant

FOYER

FOYER

FOYER

DOUBLE

TRIPLE ALLUMÉ

OVALE

ALLUMÉ

ALLUMÉ

Touche	Touche	Touche
ALLUMAGE	ALLUMAGE	ALLUMAGE
FOYER DOUBLE	FOYER TRIPLE	FOYER OVALE

•Touche ALLUMAGE FOYER DOUBLE pour activer le foyer double (voir Mise en marche et Utilisation).

•Voyant FOYER DOUBLE ALLUMÉ : il signale l’allumage du foyer double.

•Touche ALLUMAGE FOYER TRIPLE pour activer le foyer triple (voir Mise en marche et Utilisation).

•Voyant FOYER TRIPLE ALLUMÉ : il signale l’allumage du foyer triple.

•Touche ALLUMAGE FOYER OVALE pour activer le foyer ovale (voir Mise en marche et Utilisation).

•Voyant FOYER OVALE ALLUMÉ : il signale l’allumage du foyer ovale.

22