GE ZIC360NRJLH, ZIC360NRJRH, ZIC360NXALH, ZIC360NXARH, ZIC360NXBLH Installation Guide

...

0 (0)

Design Guide

with

In tall

36" Built-In Bottom-Freezer

Refrigerators

tructio

tion

monogram.com

Safety Information

BEFORE YOU BEGIN

Read these instructions completely and carefullg.

. IMPORTANT- Savetheseinstructions

for local inspector's use. Observe all governing codes and ordinances.

, Note to Installer - Be sure to leavethese

instructions with the Consumer.

, Note to Consumer- Keepthese instructions

with your Owner's Hanual for future reference.

WARNING:

This appliance must be properly grounded. See "Grounding the Refrigerator," page 9.

AVERTISSEMENT

Cet appareil dolt _tre correctement mis 6 la terre. Consulter << Mise 6 la terre du r_frig@ateur >>,page 9.

If you received a damaged refrigerator, you should immediately contact your dealer or builder.

CAUTION:

Due to the weight and size of this refrigerator, and to reduce the risk of personal injury or damage to the product-THREE PEOPLEARE REQUIRED FOR PROPER

INSTALLATION.

PRUDENCE

#,cause du poids et de la taille de ce rBfrig@ator et pour r_duire le risque de blessure et de dommages, IL FAUT

TROIS PERSONNES POUR FAIRE L'INSTALLATION CORRECTEHENT.

Skill Level -Installation of this refrigerator requires

basic mechanical, carpentry and plumbing skills. Proper installation is the responsibility of the installen Product failure due to improper installation is not covered under the GE Appliance Warranty. See the Owner's Manual for warranty information.

WARNING:

o These refrigerators are top-heavy and must

be secured to prevent the possibility of tipping forward. Anti-Tip protection is required. See page 11

for details.

, Use this appliance only for its intended purpose. , Immediately repair or replace electric service cords

that become frayed or damaged.

, Unplug the refrigerator before cleaning or making

repairs.

Repairs should be made by a qualified service

technician.

AVERTISSEMENT

. Ces rBfrig@ateurs sont Iourds en haut et il faut

les arrimer pour _viter leur basculement. II faut avoir un syst_me de protection contre le renversement.

Voir les d_tails page 11.

II ne faut utiliser cet appareil que pour I'utilisation

appropri_e.

R_parer ou remplacer imm_diatement tout cordon

_lectrique effiloch_ ou endommag_.

IIfaut d_brancher le r_frig@ateur avant le nettogage

ou toute intervention.

Les r¶tions doivent _tre faites par un technicien

qualifi_.

For Monogram local service in your area, call

1.800,444,1845.

For Monogram service in Canada, call

1.800.561.3344 For Monogram Parts and Accessories, call

1.800.626.2002. www. monogram.cam

CONTENTS

Planning Guide

The Installation Space..............................3

Dimensions and Clearances ..................3

130° Door Swing ..........................................4

90° Door Swing ............................................5

Customization Basics................................B

Panel Dimensions ......................................7

Side Panels ....................................................8

ZUG2 Grille Panel Dimensions ..............8

Installation Instructions

Tools, Hardware, Haterials ....................9

Grounding the Refrigerator ....................9

Step 1,Remove Packaging ..................10

Step 2, Install Water Line ......................10

Step 2A, RO Water Line ........................11

Step 3, Install Side Panels ....................11

Step 4, Install Anti-Tip Brackets ........11

Step 5, Level Refrigerator ....................12 Step 6, Alternate Anti-Tip Procedure.._12 Step 7, Secure Refrigerator to

Cabinetry ......................................12

Step 8, Adjust Door Swing ....................13

Step 9, Install Grille Panel ....................13

Step 10, Install Framed Panels ..........14

Step 1OA, Install Overlay Panels ......15

Step 11, Connect Water Supply ........16

Step 12, Connect Power ........................16

Step 13, Start Icemaker ........................16

Step 14, Install Toekick ..........................17

Design Guide

THE INSTALLATION SPACE

35-1/2"

FinishedWidth The finished cutout width

must be B5-1/2".

84-1/2"max 75"From

83-1/2"min FloortoBottom

Finished of ElectricalArea 0per

Water And Electrical Locations Electrical and water supply must be located as shown.

The cutout depth must be 24" The refrigerator will project forward, slightly beyond

adjacent cabinetry, depending on your installation.

Cutout depth beneath a soffit: When installed beneath a soffit, the soffit cannot exceed

the 24" installation depth shown. The top case trim overlaps the bottom of the soffit.

Additional Specifications

• A 115 volt 60Hz.,15 or 20 amp power supply is required. An individual properly grounded branch

circuit or circuit breaker is recommended. Install a properly grounded 3-prong electrical receptacle

recessed into the back wall. Electrical must be located

on rearwallasshown.

Note:GFI(groundfaultinterrupter)isnot recommended.

• Water linecan entertheopeningthroughthefloor

orbuckwall.RouteGE SmartConnectTM kitor1/4"O.D. coppertubingbetweenthecoldwaterlineand the

waterconnectionlocution.The tubingshouldbe

long enough to extend to the front of the refrigeratoE Installation of an easily accessible shut-off valve in

the water line is required.

WallView

DIMENSIONS AND CLEARANCES

35"

CaseWidth

,_ CaseDepth

T _84"From

"83-1/2" Floorto

at TopFlame

Rear m*

_._36"_ Frameto

DepthIncludingHandles:

26-7/8"FlamedModels

27-3/4" Stainless Steel Models

28-11/16"ProfessionalStyleMe@is

Product Clearances

These refrigerators are equipped with a 2-position door

stop.The factory set 1BO° door swing can be adjusted to 90° if clearance to adjacent cabinets or walls isrestricted.

130"DoorSwing

130°

......... J_

Allow 25" minimum clearance for o full 1BO° door

swing. Allow 15" for pan removal. For o 90° door swing, allow 4" min. clearance to o wall,

for framed and stainless steel models. Allow 5" min.

clearance for professional style models. If the 90° door stop position is used,pan access is maintained, but pan

removal is restricted. Seeillustrations pages 4 and 5to determine door swing

interaction with adjacent cabinets or countertops.

25-3/8"FramedMe@is 25-3/4"StainlessSteelModels

FrameWidth

*Min. Distance to Wall

* Shipping height. The

refrigerator con be adjusted to fit into o

cutout that is 83-1/2" min. to 84-1/2" max.

height. Note that the top case trim at the front is

1/2" higher and will overlap upper cabinetry or soffit. Use leveling legs

and wheels for o maximum 1" height

adjustment.

23-7/8"

90°Door Swing Frame

90°

"_-.... ! andFramed

Behind

136-3/4"

I I

*4" Stainless

5" ProSeries

models.

ZUG2,ZUGSS2Unified Grille Panel Kit

• If you are installing two refrigerators, side by side, the installation space must be 71-1/2" wide.

Note: Additional cutout width may be required when side panels are used. Add side panel thickness to the finished

cutout to calculate rough-in width.

• The water and electrical locations for each product

must belocated as shown.

• A separate 115V, 60Hz., 15 or 20 amp power supply is

recommended for each product.

84-1/2"max

83-1/2"rain

Finished Opening

--- 71-1/2"FinishedWidth_ ,_2-5/16" _ WallView

_F_[lectrJcal-_ _ 24-3/16"

10" 10"

-24" CutoutDepth FloortoBottom

3-1/2" 3-1/2" 3q/2" 3-1/2"

ofElectricalArea

,_ 5,_5,,_

Water Supply

75"From

Refrigerator

Design Guide

23-7/8" From

Rearof

Refrigerator

Frameless Cabinets: The case trim overlaps cabinets at the top and sides.

Therefore, fromeless cabinets mo U require filler strips to prevent interference with cabinet door swing. The opening must allow for filler strips.

08se

Trim

1/4"

Door

1/2" ,'

i i i i

1_' 2"

3/4"

1-1/4"

; I

1-3/4"

1-1/2"

"" 3/4" Overlay

2-3/4"

2q/2"

2-1/4"

Panel

"', (Nominal Size

Top View

130° DOOR SWING

(factory setting) Scale i:I

I-1/4"

Refrigerator

Design Guide

CaseTrim

Frameless Cabinets: The cose trim overlaps

cabinets at the top and sides. Therefore, frameless

cabinets may require filler strips to prevent

interference with cabinet door swing. The opening

must allow for filler strips.

23-7/8"

FromRearof

Refrigerator

Top View 90° DOOR SWING

(optional setting) Scale 1:1

Door

3/4"Overlay

Panel

(NominalSize)

1-1/4"

Design Guide

CUSTOMIZATION BASICS:

Framed Or Overlag Panels, Custom Handles and Accessorg Kits

Professional Stgle Stainless Steel Refrigerators Stainless steel wrapped refrigerators with beveled edges and professional style handles. These models are shipped ready for installation.

Stainless Steel Wrapped Refrigerators Stainless steel wrapped refrigerators with beveled edges

and tubular stainless steel handles that coordinate with other Monogram appliances. These models are shipped

ready for installation.

Trimmed Refrigerators Trimmed refrigerators are designed to be customized with decorative panels. Field installed custom door and grille panels are required.

Framed panels You may install 1/4" thick custom panels from your cabinet manufactureE The decorative panel slides into the factory installed trim. Or,order black, white and stainless steel accessory panels from your Monogram dealeE

Overlay panels You may also choose to install custom overlay panels from your cabinet manufacturer. This design provides a seamless appearance which integrates smoothly with surrounding cabinetry.

yPanel

DoorHandle

Standard supplied handles shown in 3/4" overlay panel position.

-- 1/4"ThickBackerPanel

SpacerPanel

Door and Drawer Handles The standard supplied handles can beadjusted to

accommodate both framed or overlay panels. Custom handles of your choice, supplied by your cabinet maker can also be installed on overlay panels. If desired, you may order ZKHCSS2Monogram stainless steel tubular handle kit for 3/4" overlay panels.

Framed Panel

Standard supplied handles shown in 1/4" panel position.

Optional Accessorg Kits , ZKHCSS2:Monogram Tubular Stainless Steel handles

designed to fit 3/4" overlay panels.This kit also includes a handle side trim for custom handles.

, ZUG2:For side-by-side installation of two trimmed

bottom-freezer refrigerators. Thiskit provides for the installation of a unified custom grille panel to span the

width of two units using a framed or overlay panel.

ZUGSS2:For side-by-side installation of two stainless steel wrapped bottom-freezer refrigerators. This kit provides a unified stainless steel grille panel to span

the width of two units.

Side Panels Side panels must be used whenever the sides of the

refrigerator will be exposed.

, ZKHCT:Handle side trim for left-hand and right-hand

doors. For use on 3/4" custom panels when using a custom handle.

Accessory Panels White, black and stainless steel accessory panels are

available from your Monogram dealer. Panels are cut

to size and reads to install. ZPBC360-Black, ZPWC360-White,

ZPSC360-Stainless Steel Panels

+ 14 hidden pages