GE ZIC360NRHLH, ZIC360NRHRH, ZICP360SLBSS, ZICP360SLCSS, ZICP360SLDSS Installation Guide

Installation
Instructions

36" Built-In Bottom-Freezer
Refrigerators

Design6uide

With InstallationInstructions

Pub.No.49-60468
PartNo.224D1145PO01

07-06JR

0

Monogram.*

Safety Information

BEFORE YOU BEGIN

Read these ins_uctions completely and carefully.

•IMPORTANT - Savetheseinstructions

for local inspector's use. Observe all governing codes
and ordinances.

• Note to Installer -- Be sure to leave these

instructions with the Consumer.

• Note to Consumer -- Keep these instructions

with your Owner's Manual for future reference.

WARNING:

This appliance must be properly grounded. See
"Grounding the Refrigerator," page 9.

AVERTISSEMENT

Cet appareil dolt 6tre correctement mis _ la terre.
Consulter, Mise fi la terre du rdfrig6rateur ,,, page 9.

If you received a damaged refrigerator, you should
immediately contact your dealer or builder.

CAUTION:

Due to the weight and size of this refrigerator, and
to reduce the risk of personal injury or damage to

the product--THREE PEOPLE ARE REQUIRED
FOR PROPER INSTALLATION.

PRUDENCE

A.cause du poids et de la taille de ce r6frig_rator et
pour r6duire le risque de blessure et de dommages,

IL FAUT TROIS PERSONNES POUR FAIRE
L'INSTALLATION CORRECTEMENT.

Skill Level -- Installation of this refrigerator
requires basic mechanical, carpentry and plumbing

skills. Proper installation is the responsibility of the
installer. Product failure due to improper installation

is not covered under the GE Appliance Warranty.
See the Owner's Manual for warranty information.

WARNING:

• These refrigerators are top-heavy and must
be secured to prevent the possibility of tipping
forward. Anti-Tip protection is required. See page

11 for details.

• Use this appliance only for its intended purpose.

• Immediately repair or replace electric service cords
that become frayed or damaged.

• Unplug the refrigerator before cleaning or making
repairs.

• Repairs should be made by a qualified service
technician.

AVERTISSEMENT

• Ces rdfrigdrateurs sent lourds en haut et il faut les
arrimer pour 6viter leur basculement, I] faut avoir
un syst_me de protection centre le renversement.

Voir les d6tails page 11,

• Il ne faut ufiliser cet appareil que pour l'utilisation
appropride.

• R6parer ou remplacer imm6diatement tout cordon
dlectrique effilochd ou endommag6.

• Il faut ddbrancher le r6frig6rateur avant le
nettoyage ou toute intervention.

• Les r_parations doivent 6tre faites par un
technicien qualifi6.

For Monogram local service in your area, call

1.800.444.1845.

For Monogram service in Canada, call

1.888.880.3030

For Monogram Parts and Accessories, call

1.800.626.2002.

www.monogram.com

CONTENTS

PlanningGuide

The InstallationSpace............................3

DimensionsandClearances..................3

130° DoorSwing......................................4

90° DoorSwing........................................5

CustomizationBasics..............................6

PanelDimensions....................................7

SidePanels................................................8

ZUG2GrillePanelDimensions..............8

Installation Instructions

Tools,Hardware, Materials ....................9

Groundingthe Refrigerator ....................9

Step 1, Remove Packaging ..................10

Step 2, InstallWater Line......................10

Step2A,R0 Water Line ........................11

Step 3, Install Side Panels ....................11

Step 4, Install Anti-lip Brackets ..........11

Step 5, Level Refrigerator ....................12

Step 6, Alternate Anti-Tip Procedure,,12

Step 7, Secure Refrigerator to

Cabinetry ....................................12

Step8, AdjustDoor Swing....................13

Step9, InstallGrillePanel....................13

Step10,Install FramedPanels............14

Step1OA,InstallOverlayPanels..........15

Step11,ConnectWater Supply..........16

Step12,ConnectPower........................16

Step13,Startleemaker ........................16

Step14,InstallTeekick..........................17

Design Guide

THE INSTALLATION SPACE

35-1/2'

FinishedWidth

The finished 1' [xc
cutout width [ [ _2-5/16"

must be [ 11 '_=T .

[ 1[ 10" _-Electrieal

84-1/21max_ Area

83-t/2 min

Finished

IL_24" CutoutDepth

) I

WallView

75"From

FloortoBottom

ofElectricalArea

OpeoingII

5"

2

...........

Water And Electrical Locations

Electrical and water supply must be located as shown.

The cutout depth must be 24"

The refrigerator will project forward, slightly beyond
adjacent cabinetry, depending on your installation.

Cutout depth beneath a soffit:

When installed beneath a soffit, the soffit cannot
exceed the 24" installation depth shown. The top case

trim overlaps the bottom of the soffit.

Additional Specifications

• A 115 volt 60Hz., 15 or 20 amp power supply is
required. An individual properly grounded branch

circuit or circuit breaker is recommended. Install
a properly grounded 3-prong electrical receptacle

recessed into the back wall. Electrical must be
located on rear wall as shown.

Note: GFI (ground fault interrupter) is not
recommended.

• Water line can enter the opening through the
floor or back wall. Route GE SmartConnect TM kit or

1/4" O.D. copper tubing between the cold water
line and the water connection location. The tubing

should be long enough to extend to the front of the
refrigerator. Installation of an easily accessible
shut-off valve in the water line is required.

DIMENSIONS AND CLEARANCES

35" 25-3/8'FramedModels

CaseWidth 25-3/4'StainlessSteelModels

* Shippingheight.The

refrigeratorcanbe adjusted

to fit intoacutoutthatis

"83-1 Floorto

at TopFrame

From

I

}6"Frameto

FrameWidth

DepthIncludin Handles:

26-7/8'Frame_Models
27-3/4"StaintessSteelModels
28-11/16'professionalStyleModels

Product Clearances

These refrigerators are equipped with a 2-position door
stop. The factory set 130 ° door swing can be adjusted to
90 ° if clearance to adjacent cabinets or walls is restricted.

\

130"

Allow 25" minimum clearance for a full 130 ° door
swing. Allow 15" for pan removal.

For a 90 ° door swing, allow 4" min. clearance to a
wall, for framed and stainless steel models. Allow 5"

min. clearance for professional style models. If the
90 ° door stop position is used, pan access is maintained,
but pata removal is restricted.

See illustrations pages 4 and 5 to determine door swing
interaction with adjacent cabinets or countertops.

83-1/2"min.to 84-1/2'max.

height.Notethat thetop

casetrim atthefrontis

1/2"higherandwill ovedap

uppercabinetryorsoffit
Uselevelinglegsandwheels

fora maximum1"height
adjustment

2Y3.7/8

9O"DoorSwing ,Fra_eBehmd

-3/4"

90" Ill "4" Stainless

_---[_L[ andFramed

•Min.DistancetoWall

models.

_1_ 5"ProSeries

ZUG2, ZUGSS2 Unified Grille Panel Kit

• If you are installing two refrigerators, side by side,
the installation space must be 71-1/2" wide.

Note:Additional cutoutwidthmayberequired whensidepanels
are used,Addsidepanelthicknessto thefinished cutoutto
calculaterough-inwidth.

• The water and electrical locations for each product
must be located as shown.

• A separate 115V, 60Hz., 15 or 20 amp power supply
is recommended for each product.

84-1/2"max

83-1/Tmin

Finished

Opening

3-1/2"

75"From

Floorto Bottom

ofElectricalArea

3-1/2"

3

Refrigerator

Design Guide

FramelessCabinets:Thecasetrim

overlapscabinetsatthetopendsides,
ThereforeframeLesscabinetsmay require
fillerstripsto preventinterferencewith

23-7/8"From

Rearof

Refrigerator

cabinetdoorswing.The openingmust

allowfor filler strips.

r

Case

Trim

1/4":

3/4"

1/2"

Top View

130 ° DOOR SWING
(factory setting)

Scale 1:1

Door

%

4

Refrigerator

Design Guide

--Case_im

FramelessCabinets:The
casetrim overlapscabinets

atthetop andsides.

Therefore,frameless

cabinetsmay requirefiller
stripsto preventinterference

with cabinetdoorswing.The

openingmust allowfor filler

strips.

23-7/8"

FromRearof

Refri .=rator

................ 1/4"

Door

.... ;---4 ..... 1/2"

3/4"Overlay

(NominalSize)

3/4"

1"

1-1/4"

- 1-1/2"

Panel

Top View
90 ° DOOR SWING

(optional setting)
Scale 1:1

5

Design Guide

CUSTOMIZATION BASICS:
Framed Or Overlay Panels, Custom Handles and Accessory Kits

Professional Style Stainless Steel Refrigerators

Stainless steel wrapped refrigerators with beveled
edges and professional style handles. These models

are shipped ready for installation.

Stainless Steel Wrapped Refrigerators

Stainless steel wrapped refrigerators with beveled
edges and tubular stainless steel handles

that coordinate with other Monogram appliances.
These models are shipped ready for installation.

Trimmed Refrigerators

Trimmed refrigerators are designed to be customized

with decorative panels. Field installed custom door

and grille panels are required.

Framed panels

You may install 1/4" thick custom panels from your

cabinet manufacturer. The decorative panel slides
into the factory installed trim. Or, order black,

white and stainless steel accessory panels from your

Monogram dealer.

Overlay panels

You may also choose to install custom overlay panels

from your cabinet manufacturer. This design provides
a seamless appearance which integrates smoothly with
surrounding cabinetry.

lyPanel

Standard ;pacerPanel
DoerHandle I/4" ThickBackerPanel

Standardsuppliedhandlesshownin314"overlay panelposition.

Door and Drawer Handles

The standard supplied handles can be adjusted to
accommodate both framed or overlay panels. Custom

handles of your choice, supplied by your cabinet maker
can also be installed on overlay panels. If desired, you

may order ZKHCSS2 Monogram stainless steel tubular
handle kit for 3/4" overlay panels.

StandardDoorHandle FramedPanel

Standardsuppliedhandlesshownin1/4"panelposition.

Optional Accessory Kits

• ZKHCSS2: Monogram Tubular Stainless Steel handles
designed to fit 3/4" overlay panels. This kit also

includes a handle side trim for custom handles.

• ZUG2: For side-by-side installation of two trimmed

bottom-freezer refrigerators. This kit provides for the
installation of a unified custom grille panel to span the

width of two units using a framed or overlay panel.

• ZUGSS2: For side-by-side installation of two stainless

steel wrapped bottom-freezer refrigerators. This kit

provides a unified stainless steel grille panel to span
the width of two units.

Side Panels

Side panels must be used whenever the sides of the
refrigerator will be exposed.

Accessory Panels

White, black and stainless steel accessory panels are
available from your Monogram dealer. Panels are cut

to size and ready to install.
ZPBC360--Black, ZPWC360-White,

ZPSC360--Stainless Steel Panels

6