fanuc 16 i -LA, 160 i-LA Operators Manual

GE Fanuc Automation

Computer Numerical Control Products

Series 16 i / 160 i–LA

Operator's Manual

GFZ-63194EN/02 August 2000

Warnings, Cautions, and Notes as Used in this Publication

Warning notices are used in this publication to emphasize that hazardous voltages, currents, temperatures, or other conditions that could cause personal injury exist in this equipment or may be associated with its use.

In situations where inattention could cause either personal injury or damage to equipment, a Warning notice is used.

Caution notices are used where equipment might be damaged if care is not taken.

GFL-001

Warning

Caution

Note

Notes merely call attention to information that is especially significant to understanding and operating the equipment.

This document is based on information available at the time of its publication. While efforts have been made to be accurate, the information contained herein does not purport to cover all details or variations in hardware or software, nor to provide for every possible contingency in connection with installation, operation, or maintenance. Features may be described herein which are not present in all hardware and software systems. GE Fanuc Automation assumes no obligation of notice to holders of this document with respect to changes subsequently made.

GE Fanuc Automation makes no representation or warranty, expressed, implied, or statutory with respect to, and assumes no responsibility for the accuracy, completeness, sufficiency, or usefulness of the information contained herein. No warranties of merchantability or fitness for purpose shall apply.

SAFETY PRECAUTIONS

This section describes the safety precautions related to the use of CNC units. It is essential that these precautions be observed by users to ensure the safe operation of machines equipped with a CNC unit (all descriptions in this section assume this configuration). Note that some precautions are related only to specific functions, and thus may not be applicable to certain CNC units. Users must also observe the safety precautions related to the machine, as described in the relevant manual supplied by the machine tool builder. Before attempting to operate the machine or create a program to control the operation of the machine, the operator must become fully familiar with the contents of this manual and relevant manual supplied by the machine tool builder.

Contents

1. DEFINITION OF WARNING, CAUTION, AND NOTE s–2. . . . . . . . . . . . . . . . . . . . . . .

2. GENERAL WARNINGS AND CAUTIONS s–3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3. WARNINGS AND CAUTIONS RELATED TO PROGRAMMING s–5. . . . . . . . . . . . .

4. WARNINGS AND CAUTIONS RELATED TO HANDLING s–7. . . . . . . . . . . . . . . . . . .

5. WARNINGS RELATED TO DAILY MAINTENANCE s–9. . . . . . . . . . . . . . . . . . . . . . . .

s–1

SAFETY PRECAUTIONS

B–63194EN/02

DEFINITION OF WARNING, CAUTION, AND NOTE

This manual includes safety precautions for protecting the user and preventing damage to the machine. Precautions are classified into W arning and Caution according to their bearing on safety. Also, supplementary information is described as a Note. Read the Warning, Caution, and Note thoroughly before attempting to use the machine.

WARNING

Applied when there is a danger of the user being injured or when there is a danger of both the user being injured and the equipment being damaged if the approved procedure is not observed.

CAUTION

Applied when there is a danger of the equipment being damaged, if the approved procedure is not observed.

NOTE

The Note is used to indicate supplementary information other than Warning and Caution.

` Read this manual carefully, and store it in a safe place.

s–2

B–63194EN/02

SAFETY PRECAUTIONS

GENERAL W ARNINGS AND CAUTIONS

WARNING

1. Never attempt to machine a workpiece without first checking the operation of the machine.

Before starting a production run, ensure that the machine is operating correctly by performing a trial run using, for example, the single block, feedrate override, or machine lock function or by operating the machine with neither a tool nor workpiece mounted. Failure to confirm the correct operation of the machine may result in the machine behaving unexpectedly, possibly causing damage to the workpiece and/or machine itself, or injury to the user.

2. Before operating the machine, thoroughly check the entered data.

Operating the machine with incorrectly specified data may result in the machine behaving unexpectedly , possibly causing damage to the workpiece and/or machine itself, or injury to the user.

3. Ensure that the specified feedrate is appropriate for the intended operation. Generally , for each

machine, there is a maximum allowable feedrate. The appropriate feedrate varies with the intended operation. Refer to the manual provided with the machine to determine the maximum allowable feedrate. If a machine is run at other than the correct speed, it may behave unexpectedly , possibly causing damage to the workpiece and/or machine itself, or injury to the user.

4. When using a tool compensation function, thoroughly check the direction and amount of

compensation. Operating the machine with incorrectly specified data may result in the machine behaving unexpectedly , possibly causing damage to the workpiece and/or machine itself, or injury to the user.

5. The parameters for the CNC and PMC are factory–set. Usually , there is not need to change them.

When, however, there is not alternative other than to change a parameter, ensure that you fully understand the function of the parameter before making any change. Failure to set a parameter correctly may result in the machine behaving unexpectedly , possibly causing damage to the workpiece and/or machine itself, or injury to the user.

6. Some laser beams are invisible (cannot be seen by the eye).

Before approaching the nozzle, check that the laser beam is off. Failure to do so subjects the user to the danger of serious injury.

7. A workpiece that has just undergone laser beam processing is very hot. Touching it, therefore,

may cause injury to the user.

s–3

SAFETY PRECAUTIONS

B–63194EN/02

CAUTION

1. Immediately after switching on the power , do not touch any of the keys on the MDI panel until

the position display or alarm screen appears on the CNC unit. Some of the keys on the MDI panel are dedicated to maintenance or other special operations. Pressing any of these keys may place the CNC unit in other than its normal state. Starting the machine in this state may cause it to behave unexpectedly.

2. The operator’s manual and programming manual supplied with a CNC unit provide an overall

description of the machine’s functions, including any optional functions. Note that the optional functions will vary from one machine model to another. Therefore, some functions described in the manuals may not actually be available for a particular model. Check the specification of the machine if in doubt.

3 Some functions may have been implemented at the request of the machine–tool builder. When

using such functions, refer to the manual supplied by the machine–tool builder for details of their use and any related cautions.

NOTE

Programs, parameters, and macro variables are stored in nonvolatile memory in the CNC unit. Usually, they are retained even if the power is turned of f. Such data may be deleted inadvertently, however, or it may prove necessary to delete all data from nonvolatile memory as part of error recovery. T o guard against the occurrence of the above, and assure quick restoration of deleted data, backup all vital data, and keep the backup copy in a safe place.

s–4

B–63194EN/02

1. Coordinate system setting

SAFETY PRECAUTIONS

W ARNINGS AND CAUTIONS RELATED TO PROGRAMMING

This section covers the major safety precautions related to programming. Before attempting to perform programming, read the supplied operator’s manual and programming manual carefully such that you are fully familiar with their contents.

WARNING

If a coordinate system is established incorrectly, the machine may behave unexpectedly as a result of the program issuing an otherwise valid move command. Such an unexpected operation may damage the tool, the machine itself, the workpiece, or cause injury to the user.

2. Positioning by nonlinear interpolation

When performing positioning by nonlinear interpolation (positioning by nonlinear movement between the start and end points), the tool path must be carefully confirmed before performing programming. Positioning involves rapid traverse. If the tool collides with the workpiece, it may damage the tool, the machine itself, the workpiece, or cause injury to the user.

3. Function involving a rotation axis

When programming polar coordinate interpolation or normal–direction (perpendicular) control, pay careful attention to the speed of the rotation axis. Incorrect programming may result in the rotation axis speed becoming excessively high, such that centrifugal force causes the chuck to lose its grip on the workpiece if the latter is not mounted securely. Such mishap is likely to damage the tool, the machine itself, the workpiece, or cause injury to the user.

4. Inch/metric conversion

Switching between inch and metric inputs does not convert the measurement units of data such as the workpiece origin offset, parameter, and current position. Before starting the machine, therefore, determine which measurement units are being used. Attempting to perform an operation with invalid data specified may damage the tool, the machine itself, the workpiece, or cause injury to the user.

5. Stroke check

After switching on the power, perform a manual reference position return as required. Stroke check is not possible before manual reference position return is performed. Note that when stroke check is disabled, an alarm is not issued even if a stroke limit is exceeded, possibly damaging the tool, the machine itself, the workpiece, or causing injury to the user.

s–5

SAFETY PRECAUTIONS

CAUTION

1. Absolute/incremental mode

If a program created with absolute values is run in incremental mode, or vice versa, the machine may behave unexpectedly.

2. Plane selection

If an incorrect plane is specified for circular interpolation, helical interpolation, or a canned cycle, the machine may behave unexpectedly. Refer to the descriptions of the respective functions for details.

3. Torque limit skip

Before attempting a torque limit skip, apply the torque limit. If a torque limit skip is specified without the torque limit actually being applied, a move command will be executed without performing a skip.

4. Programmable mirror image

B–63194EN/02

Note that programmed operations vary considerably when a programmable mirror image is enabled.

5. Compensation function

If a command based on the machine coordinate system or a reference position return command is issued in compensation function mode, compensation is temporarily canceled, resulting in the unexpected behavior of the machine. Before issuing any of the above commands, therefore, always cancel compensation function mode.

6. Tracing control

Tracing control is performed to keep the gap constant. During tracing control, ensure that the nozzle does not move to any location other than around the workpiece. Otherwise, the nozzle may collide with the machine, possibly causing damage to the nozzle and the machine.

s–6

B–63194EN/02

SAFETY PRECAUTIONS

W ARNINGS AND CAUTIONS RELATED TO HANDLING

This section presents safety precautions related to the handling of machine tools. Before attempting to operate your machine, read the supplied operator’s manual and programming manual carefully, such that you are fully familiar with their contents.

WARNING

1. Manual operation

When operating the machine manually , determine the current position of the tool and workpiece, and ensure that the movement axis, direction, and feedrate have been specified correctly. Incorrect operation of the machine may damage the tool, the machine itself, the workpiece, or cause injury to the operator.

2. Manual reference position return

After switching on the power, perform manual reference position return as required. If the machine is operated without first performing manual reference position return, it may behave unexpectedly . Stroke check is not possible before manual reference position return is performed. An unexpected operation of the machine may damage the tool, the machine itself, the workpiece, or cause injury to the user.

3. Manual numeric command

When issuing a manual numeric command, determine the current position of the tool and workpiece, and ensure that the movement axis, direction, and command have been specified correctly, and that the entered values are valid. Attempting to operate the machine with an invalid command specified may damage the tool, the machine itself, the workpiece, or cause injury to the operator.

4. Manual handle feed

In manual handle feed, rotating the handle with a large scale factor, such as 100, applied causes the tool and table to move rapidly. Careless handling may damage the tool and/or machine, or cause injury to the user.

5. Origin/preset operation

Basically, never attempt an origin/preset operation when the machine is operating under the control of a program. Otherwise, the machine may behave unexpectedly, possibly damaging the tool, the machine itself, the tool, or causing injury to the user.

s–7

SAFETY PRECAUTIONS

WARNING

6. Workpiece coordinate system shift

Manual intervention, machine lock, or mirror imaging may shift the workpiece coordinate system. Before attempting to operate the machine under the control of a program, confirm the coordinate system carefully. If the machine is operated under the control of a program without making allowances for any shift in the workpiece coordinate system, the machine may behave unexpectedly, possibly damaging the tool, the machine itself, the workpiece, or causing injury to the operator.

7. Software operator ’s panel and menu switches

Using the software operator’s panel and menu switches, in combination with the MDI panel, it is possible to specify operations not supported by the machine operator’s panel, such as mode change, override value change, and jog feed commands. Note, however, that if the MDI panel keys are operated inadvertently, the machine may behave unexpectedly, possibly damaging the tool, the machine itself, the workpiece, or causing injury to the user.

B–63194EN/02

CAUTION

1. Manual intervention

If manual intervention is performed during programmed operation of the machine, the tool path may vary when the machine is restarted. Before restarting the machine after manual intervention, therefore, confirm the settings of the manual absolute switches, parameters, and absolute/incremental command mode.

2. Feed hold, override, and single block

The feed hold, feedrate override, and single block functions can be disabled using custom macro system variable #3004. Be careful when operating the machine in this case.

3. Dry run

Usually, a dry run is used to confirm the operation of the machine. During a dry run, the machine operates at dry run speed, which differs from the corresponding programmed feedrate. Note that the dry run speed may sometimes be higher than the programmed feed rate.

4. Cutter compensation in MDI mode

Pay careful attention to a tool path specified by a command in MDI mode, because cutter compensation is not applied. When a command is entered from the MDI to interrupt in automatic operation in cutter compensation mode, pay particular attention to the tool path when automatic operation is subsequently resumed. Refer to the descriptions of the corresponding functions for details.

5. Program editing

If the machine is stopped, after which the machining program is edited (modification, insertion, or deletion), the machine may behave unexpectedly if machining is resumed under the control of that program. Basically , do not modify, insert, or delete commands from a machining program while it is in use.

s–8

B–63194EN/02

1. Memory backup battery replacement

SAFETY PRECAUTIONS

W ARNINGS RELATED TO DAILY MAINTENANCE

WARNING

When replacing the memory backup batteries, keep the power to the machine (CNC) turned on, and apply an emergency stop to the machine. Because this work is performed with the power on and the cabinet open, only those personnel who have received approved safety and maintenance training may perform this work. When replacing the batteries, be careful not to touch the high–voltage circuits (marked fitted with an insulating cover). Touching the uncovered high–voltage circuits presents an extremely dangerous electric shock hazard.

and

NOTE

The CNC uses batteries to preserve the contents of its memory, because it must retain data such as programs, offsets, and parameters even while external power is not applied. If the battery voltage drops, a low battery voltage alarm is displayed on the machine operator’s panel or screen. When a low battery voltage alarm is displayed, replace the batteries within a week. Otherwise, the contents of the CNC’s memory will be lost. Refer to the maintenance section of the operator’s manual or programming manual for details of the battery replacement procedure.

s–9

SAFETY PRECAUTIONS

B–63194EN/02

WARNING

2. Absolute pulse coder battery replacement

NOTE

The absolute pulse coder uses batteries to preserve its absolute position. If the battery voltage drops, a low battery voltage alarm is displayed on the machine operator’s panel or screen. When a low battery voltage alarm is displayed, replace the batteries within a week. Otherwise, the absolute position data held by the pulse coder will be lost. Refer to the maintenance section of the operator’s manual or programming manual for details of the battery replacement procedure.

and

s–10

B–63194EN/02

3. Fuse replacement

SAFETY PRECAUTIONS

WARNING

For some units, the chapter covering daily maintenance in the operator’s manual or programming manual describes the fuse replacement procedure. Before replacing a blown fuse, however, it is necessary to locate and remove the cause of the blown fuse. For this reason, only those personnel who have received approved safety and maintenance training may perform this work. When replacing a fuse with the cabinet open, be careful not to touch the high–voltage circuits (marked Touching an uncovered high–voltage circuit presents an extremely dangerous electric shock hazard.

and fitted with an insulating cover).

s–11

B–63194EN/02

SAFETY PRECAUTIONS S–1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

I. GENERAL 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1. GENERAL 3. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.1 GENERAL FLOW OF OPERATION OF CNC MACHINE TOOL 5. . . . . . . . . . . . . . . . . . . . . . . . .

1.2 NOTES ON READING THIS MANUAL 6. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

II. PROGRAMMING 7. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1. GENERAL 9. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.1 NOZZLE MOVEMENT ALONG WORKPIECE PARTS FIGURE–INTERPOLATION 10. . . . . . . .

1.2 FEED–FEED FUNCTION 12. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3 PART DRAWING AND NOZZLE MOVEMENT 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3.1 Reference Position (Machine–Specific Position) 13. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3.2 Coordinate System on Part Drawing and Coordinate System Specified

1.3.3 How to Indicate Command Dimensions for Moving the Machine Absolute,

1.4 COMMAND FOR MACHINE OPERATIONS–MISCELLANEOUS FUNCTION 18. . . . . . . . . . . . .

1.5 PROGRAM CONFIGURATION 19. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.6 NOZZLE MOVEMENT RANGE–STROKE 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

by CNC – Coordinate System 14. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Incremental Commands 17. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2. CONTROLLED AXES 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1 CONTROLLED AXES 25. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2 AXIS NAME 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3 INCREMENT SYSTEM 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4 MAXIMUM STROKE 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3. PREPARATORY FUNCTION (G FUNCTION) 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4. INTERPOLATION FUNCTIONS 34. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.1 POSITIONING (G00) 35. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2 SINGLE DIRECTION POSITIONING (G60) 37. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.3 LINEAR INTERPOLATION (G01) 38. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4 CIRCULAR INTERPOLATION (G02, G03) 40. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5 HELICAL INTERPOLATION (G02, G03) 45. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.6 SPIRAL INTERPOLATION, CONICAL INTERPOLATION (G02, G03) 46. . . . . . . . . . . . . . . . . . . .

4.7 POLAR COORDINATE INTERPOLATION (G12.1, G13.1) 51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.8 CYLINDRICAL INTERPOLATION (G07.1) 55. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.9 HYPOTHETICAL AXIS INTERPOLATION (G07) 58. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.10 SKIP FUNCTION(G31) 61. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.11 MULTISTAGE SKIP (G31) 63. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5. FEED FUNCTIONS 64. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.1 GENERAL 65. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.2 RAPID TRAVERSE 67. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

c–1

Table of Contents

B–63194EN/02

5.3 MACHINING FEED 68. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4 CUTTING FEEDRATE CONTROL 70. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4.1 Exact Stop (G09, G61) Cutting Mode (G64) 71. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4.2 Automatic Corner Override 72. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4.2.1 Automatic override for inner corners (G62) 72. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4.2.2 Internal circular machining feedrate change 74. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4.3 Automatic Corner Deceleration 75. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4.3.1 Corner deceleration according to the corner angle 75. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4.3.2 Corner deceleration according to the feedrate difference between blocks along each axis 78. . . . .

5.5 DWELL (G04) 82. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6. REFERENCE POSITION 83. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.1 REFERENCE POSITION RETURN 84. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.2 FLOATING REFERENCE POSITION RETURN (G30.1) 89. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7. COORDINATE SYSTEM 90. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.1 MACHINE COORDINATE SYSTEM 91. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.2 WORKPIECE COORDINATE SYSTEM 92. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.2.1 Setting a Workpiece Coordinate System 92. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.2.2 Selecting a W orkpiece Coordinate System 93. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.2.3 Changing Workpiece Coordinate System 94. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.2.4 W orkpiece Coordinate System Preset (G92.1) 97. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.2.5 Adding Workpiece Coordinate Systems (G54.1 or G54) 99. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.3 LOCAL COORDINATE SYSTEM 101. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.4 PLANE SELECTION 103. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8. COORDINATE VALUE AND DIMENSION 104. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.1 ABSOLUTE AND INCREMENTAL PROGRAMMING (G90, G91) 105. . . . . . . . . . . . . . . . . . . . . . .

8.2 POLAR COORDINATE COMMAND (G15, G16) 106. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.3 INCH/METRIC CONVERSION (G20, G21) 109. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.4 DECIMAL POINT PROGRAMMING 110. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9. AUXILIARY FUNCTION 111. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.1 AUXILIARY FUNCTION (M FUNCTION) 112. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.2 MULTIPLE M COMMANDS IN A SINGLE BLOCK 113. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.3 M CODE GROUP CHECK FUNCTION 114. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.4 THE SECOND AUXILIARY FUNCTIONS (B CODES) 115. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10.PROGRAM CONFIGURATION 116. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10.1 PROGRAM COMPONENTS OTHER THAN PROGRAM SECTIONS 118. . . . . . . . . . . . . . . . . . . . .

10.2 PROGRAM SECTION CONFIGURATION 120. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10.3 SUBPROGRAM (M98, M99) 126. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10.4 8–DIGIT PROGRAM NUMBER 130. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.FUNCTIONS TO SIMPLIFY PROGRAMMING 133. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.1 OPTIONAL ANGLE CHAMFERING AND CORNER ROUNDING 134. . . . . . . . . . . . . . . . . . . . . . .

11.2 FIGURE COPY (G72.1, G72.2) 137. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

c–2

B–63194EN/02

Table of Contents

12.COMPENSATION FUNCTION 144. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.1 TOOL OFFSET (G45–G48) 145. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.2 OVERVIEW OF CUTTER COMPENSATION C (G40–G42) 150. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.3 DETAILS OF CUTTER COMPENSATION C 156. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.3.1 General 156. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.3.2 Nozzle Movement in Start–up 157. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.3.3 Nozzle Movement in Offset Mode 161. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.3.4 Nozzle Movement in Offset Mode Cancel 175. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.3.5 Interference Check 181. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.3.6 Overcutting by Cutter Compensation 186. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.3.7 Input Command from MDI 189. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.3.8 G53,G28,G30,G30.1 and G29 Commands in Cutter Compensation C Mode 190. . . . . . . . . . . . . . . . . . . .

12.3.9 Corner Circular Interpolation (G39) 209. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.4 CUTTER COMPENSATION VALUES, NUMBER OF COMPENSATION VALUES,

AND ENTERING VALUES FROM THE PROGRAM (G10) 211. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.5 SCALING (G50,G51) 213. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.6 COORDINATE SYSTEM ROTATION (G68, G69) 218. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.7 NORMAL DIRECTION CONTROL (G40.1, G41.1, G42.1 OR G150, G151, G152) 224. . . . . . . . . . .

12.8 PROGRAMMABLE MIRROR IMAGE (G50.1, G51.1) 229. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.CUSTOM MACRO 231. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.1 VARIABLES 232. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.2 SYSTEM VARIABLES 235. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.3 ARITHMETIC AND LOGIC OPERATION 243. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.4 MACRO STATEMENTS AND NC STATEMENTS 248. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.5 BRANCH AND REPETITION 249. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.5.1 Unconditional Branch (GOTO Statement) 249. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.5.2 Conditional Branch (IF Statement) 250. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.5.3 Repetition (While Statement) 251. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.6 MACRO CALL 253. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.6.1 Simple Call (G65) 254. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.6.2 Modal Call (G66) 258. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.6.3 Macro Call Using G Code 260. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.6.4 Macro Call Using an M Code 261. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.6.5 Subprogram Call Using an M Code 263. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.6.6 Subprogram Calls Using a T Code 264. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.7 PROCESSING MACRO STATEMENTS 265. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.8 REGISTERING CUSTOM MACRO PROGRAMS 267. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.9 LIMITATIONS 268. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.10 EXTERNAL OUTPUT COMMANDS 269. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.11 INTERRUPTION TYPE CUSTOM MACRO 273. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.11.1 Specification Method 274. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

13.11.2 Details of Functions 275. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14.PROGRAMMABLE PARAMETER ENTRY (G10) 282. . . . . . . . . . . . . . . . . . . . . . . . . . .

15.MEMORY OPERATION USING FS15 TAPE FORMAT 284. . . . . . . . . . . . . . . . . . . . . .

16.HIGH SPEED CUTTING FUNCTIONS 285. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16.1 FEEDRATE CLAMPING BY ARC RADIUS 286. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

c–3

Table of Contents

16.2 LOOK–AHEAD CONTROL (G08) 287. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16.3 HIGH–SPEED REMOTE BUFFER 289. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16.3.1 High–Speed Remote Buffer A (G05) 289. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16.3.2 High–Speed Remote Buffer B (G05) 292. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16.4 HIGH–PRECISION CONTOUR CONTROL (G05) 293. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16.5 DISTRIBUTION PROCESSING TERMINATION MONITORING FUNCTION

FOR THE HIGH–SPEED MACHINING COMMAND (G05) 301. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16.6 HIGH–SPEED LINEAR INTERPOLATION (G05) 302. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

16.7 AI CONTOUR CONTROL (G05.1) 305. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

B–63194EN/02

17.AXIS CONTROL FUNCTIONS 311. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17.1 SIMPLE SYNCHRONOUS CONTROL 312. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17.2 ROTARY AXIS ROLL–OVER 315. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17.3 TANDEM CONTROL 316. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18.SPECIFYING THE LASER FUNCTION 317. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18.1 CONTOUR MACHINING (G01, G02, G03, AND G12) 318. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18.2 PIERCING FUNCTION (G24) 320. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18.3 LASER POWER CONTROL (G63) 323. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18.4 BEAM OUTPUT CONDITION DELAY FUNCTION 329. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18.5 STEP FUNCTION 331. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18.6 ASSIST GAS CONTROL (G32) 336. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18.6.1 Flow Pattern Specification 336. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18.6.2 Direct Assist Gas Control Specification 337. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18.6.3 Direct Gas Pressure Control Specification Using the Machining Condition Setting Function 339. . . . . . . .

18.7 MACHINING CONDITION SETTING FUNCTION (E CODE) 340. . . . . . . . . . . . . . . . . . . . . . . . . . .

18.7.1 Piercing Command 340. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18.7.2 Cutting Command 341. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18.7.3 Edge Machining Function 342. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18.7.4 Startup Machining Function 347. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

18.8 HIGH–SPEED LASER MACHINING FUNCTION 349. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19.THREE–DIMENSIONAL CUTTING FUNCTION 358. . . . . . . . . . . . . . . . . . . . . . . . . . . .

19.1 POSITION CONTROL 359. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19.2 SPATIAL CIRCULAR INTERPOLATION (G12) 360. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19.3 SPATIAL CORNER ROUNDING (G33 AND G34) 362. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19.4 THREE–DIMENSIONAL COORDINATE CONVERSION FUNCTION (G68 AND G69) 364. . . . . .

19.5 PROCESSING HEAD A–AXIS LENGTH COMPENSATION FUNCTION (G71) 366. . . . . . . . . . . . .

19.6 THREE–DIMENSIONAL TRANSFORM FUNCTION 368. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

19.7 FEEDRATE CLAMP FUNCTION IN POSITION CONTROL B 372. . . . . . . . . . . . . . . . . . . . . . . . . . .

19.8 AUTOMATIC FEEDRATE OVERRIDE UNDER POSITION CONTROL B 375. . . . . . . . . . . . . . . . .

III. OPERATION 377. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1. GENERAL 379. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.1 MANUAL OPERATION 380. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.2 MOVING THE NOZZLE USING A PROGRAM–AUTOMATIC OPERATION 382. . . . . . . . . . . . . . .

c–4

B–63194EN/02

Table of Contents

1.3 OPERATIONS FOR AUTOMATIC OPERATION 383. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.4 TEST OPERATION 385. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.4.1 Check by Running the Machine 385. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.4.2 Checking the Position Display Change Without Running the Machine 386. . . . . . . . . . . . . . . . . . . . . . . .

1.5 EDITING A PROGRAM 387. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.6 DISPLAYING AND SETTING DATA 388. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.7 DISPLAY 391. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.7.1 Program Display 391. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.7.2 Current Position Display 392. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.7.3 Alarm Display 392. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.7.4 Part Count Display and Run Time Display 393. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.7.5 Graphic Display 393. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.8 DATA INPUT/OUTPUT 394. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2. OPERATIONAL DEVICES 395. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1 SETTING AND DISPLAY UNITS 396. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1.1 CNC Control Unit with 7.2”/8.4” LCD 397. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1.2 CNC Control Unit with 9.5”/10.4” LCD 397. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1.3 Separate–Type Small MDI Unit 398. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1.4 Separate–Type Standard MDI Unit (Horizontal Type) 399. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1.5 Separate–Type Standard MDI Unit (V ertical Type) 400. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.1.6 Separate–Type Standard MDI Unit (V ertical Type) (for 160i) 401. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.2 EXPLANATION OF THE KEYBOARD 402. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3 FUNCTION KEYS AND SOFT KEYS 404. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3.1 General Screen Operations 404. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3.2 Function Keys 405. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3.3 Soft Keys 406. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3.4 Key Input and Input Buffer 423. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3.5 W arning Messages 424. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.3.6 Soft Key Configuration 425. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4 EXTERNAL I/O DEVICES 426. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4.1 F ANUC Handy File 428. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4.2 F ANUC Floppy Cassette 428. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4.3 F ANUC FA Card 429. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4.4 F ANUC PPR 429. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.4.5 Portable T ape Reader 430. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.5 POWER ON/OFF 431. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.5.1 Turning on the Power 431. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.5.2 Screen Displayed at Power–on 432. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

2.5.3 Power Disconnection 433. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3. MANUAL OPERATION 434. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.1 MANUAL REFERENCE POSITION RETURN 435. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.2 JOG FEED 437. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.3 INCREMENTAL FEED 439. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.4 MANUAL HANDLE FEED 440. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

3.5 MANUAL ABSOLUTE ON AND OFF 443. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4. AUT OMATIC OPERA TION 448. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.1 MEMORY OPERATION 449. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.2 MDI OPERATION 451. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

c–5

Table of Contents

B–63194EN/02

4.3 DNC OPERATION 455. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.4 SIMULTANEOUS INPUT/OUTPUT 458. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.5 PROGRAM RESTART 460. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.6 SCHED ULING FUNCTION 468. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.7 SUBPROGRAM CALL FUNCTION (M198) 473. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.8 MANUAL HANDLE INTERRUPTION 475. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.9 MIRROR IMAGE 478. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.10 RETRACE FUNCTION 480. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

4.11 MANUAL INTERVENTION AND RETURN 487. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5. TEST OPERATION 489. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.1 MACHINE LOCK AND AUXILIARY FUNCTION LOCK 490. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.2 FEEDRATE OVERRIDE 492. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.3 RAPID TRAVERSE OVERRIDE 493. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.4 DRY RUN 494. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

5.5 SINGLE BLOCK 495. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6. SAFETY FUNCTIONS 496. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.1 EMERGENCY STOP 497. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.2 OVERTRAVEL 498. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.3 STROKE CHECK 499. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

6.4 STROKE LIMIT CHECK PRIOR TO PERFORMING MOVEMENT 503. . . . . . . . . . . . . . . . . . . . . . .

7. ALARM AND SELF–DIAGNOSIS FUNCTIONS 505. . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.1 ALARM DISPLAY 506. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.2 ALARM HISTORY DISPLAY 508. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

7.3 CHECKING BY SELF–DIAGNOSTIC SCREEN 509. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8. DATA INPUT/OUTPUT 512. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.1 FILES 513. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.2 FILE SEARCH 515. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.3 FILE DELETION 516. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.4 PROGRAM INPUT/OUTPUT 517. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.4.1 Inputting a Program 517. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.4.2 Outputting a Program 520. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.5 OFFSET DATA INPUT AND OUTPUT 522. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.5.1 Inputting Offset Data 522. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.5.2 Outputting Offset Data 523. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.6 INPUTTING AND OUTPUTTING PARAMETERS AND

PITCH ERROR COMPENSATION DATA 524. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.6.1 Inputting Parameters 524. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.6.2 Outputting Parameters 525. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.6.3 Inputting Pitch Error Compensation Data 526. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.6.4 Outputting Pitch Error Compensation Data 527. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.7 INPUTTING/OUTPUTTING CUSTOM MACRO COMMON VARIABLES 528. . . . . . . . . . . . . . . . .

8.7.1 Inputting Custom Macro Common Variables 528. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.7.2 Outputting Custom Macro Common Variable 529. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

c–6

B–63194EN/02

Table of Contents

8.8 DISPLAYING DIRECTORY OF FLOPPY CASSETTE 530. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.8.1 Displaying the Directory 531. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.8.2 Reading Files 534. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.8.3 Outputting Programs 535. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.8.4 Deleting Files 536. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.9 OUTPUTTING A PROGRAM LIST FOR A SPECIFIED GROUP 538. . . . . . . . . . . . . . . . . . . . . . . . .

8.10 DATA INPUT/OUTPUT ON THE ALL IO SCREEN 539. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.10.1 Setting Input/Output–Related Parameters 540. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.10.2 Inputting and Outputting Programs 541. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.10.3 Inputting and Outputting Parameters 546. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.10.4 Inputting and Outputting Offset Data 548. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.10.5 Outputting Custom Macro Common Variables 550. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.10.6 Inputting and Outputting Floppy Files 551. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

8.11 DATA INPUT/OUTPUT USING A MEMORY CARD 556. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9. EDITING PROGRAMS 568. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.1 INSERTING, ALTERING AND DELETING A WORD 569. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.1.1 W ord Search 570. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.1.2 Heading a Program 572. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.1.3 Inserting a W ord 573. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.1.4 Altering a W ord 574. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.1.5 Deleting a W ord 575. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.2 DELETING BLOCKS 576. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.2.1 Deleting a Block 576. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.2.2 Deleting Multiple Blocks 577. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.3 PROGRAM NUMBER SEARCH 578. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.4 SEQUENCE NUMBER SEARCH 579. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.5 DELETING PROGRAMS 581. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.5.1 Deleting One Program 581. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.5.2 Deleting All Programs 581. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.5.3 Deleting More Than One Program by Specifying a Range 582. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.6 EXTENDED PART PROGRAM EDITING FUNCTION 583. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.6.1 Copying an Entire Program 583. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.6.2 Copying Part of a Program 584. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.6.3 Moving Part of a Program 585. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.6.4 Merging a Program 586. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.6.5 Supplementary Explanation for Copying, Moving and Merging 587. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.6.6 Replacement of W ords and Addresses 589. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.7 EDITING OF CUSTOM MACROS 591. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.8 BACKGROUND EDITING 592. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

9.9 PASSWORD FUNCTION 593. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10.CREATING PROGRAMS 595. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10.1 CREATING PROGRAMS USING THE MDI PANEL 596. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10.2 AUTOMATIC INSERTION OF SEQUENCE NUMBERS 597. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

10.3 CREATING PROGRAMS IN TEACH IN MODE (PLAYBACK) 598. . . . . . . . . . . . . . . . . . . . . . . . . .

1 1.SETTING AND DISPLA YING DATA 601. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.1 SCREENS DISPLAYED BY FUNCTION KEY

11.1.1 Position Display in the Work Coordinate System 610. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

POS

c–7

609. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Table of Contents

B–63194EN/02

11.1.2 Position Display in the Relative Coordinate System 611. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.1.3 Overall Position Display 613. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.1.4 Presetting the W orkpiece Coordinate System 614. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.1.5 Actual Feedrate Display 615. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.1.6 Display of Run Time and Parts Count 616. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.1.7 Setting the Floating Reference Position 617. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.1.8 Operating Monitor Display 618. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.2 SCREENS DISPLAYED BY FUNCTION KEY

PROG

(IN MEMORY MODE OR MDI MODE) 619. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.2.1 Program Contents Display 620. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.2.2 Current Block Display Screen 621. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.2.3 Next Block Display Screen 622. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.2.4 Program Check Screen 623. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.2.5 Program Screen for MDI Operation 625. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.2.6 Stamping the Machining Time 626. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.3 SCREENS DISPLAYED BY FUNCTION KEY

11.3.1 Displaying Memory Used and a List of Programs 634. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.3.2 Displaying a Program List for a Specified Group 637. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.4 SCREENS DISPLAYED BY FUNCTION KEY

11.4.1 Setting and Displaying the Tool Offset Value 641. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.4.2 Displaying and Entering Setting Data 644. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.4.3 Sequence Number Comparison and Stop 646. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.4.4 Displaying and Setting Run Time, Parts Count, and Time 648. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.4.5 Displaying and Setting the W orkpiece Origin Offset Value 650. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.4.6 Direct Input of Measured W orkpiece Origin Offsets 651. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.4.7 Displaying and Setting Custom Macro Common V ariables 653. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.4.8 Displaying Pattern Data and Pattern Menu 654. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.4.9 Displaying and Setting the Software Operator’s Panel 656. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

PROG

(IN THE EDIT MODE) 634. . . . . . . . . . . . . . .

OFFSET SETTING

640. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.5 SCREENS DISPLAYED BY FUNCTION KEY

SYSTEM

11.5.1 Displaying and Setting Parameters 659. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.5.2 Displaying and Setting Pitch Error Compensation Data 661. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.6 DISPLAYING THE PROGRAM NUMBER, SEQUENCE NUMBER, AND STATUS,

AND WARNING MESSAGES FOR DATA SETTING OR INPUT/OUTPUT OPERATION 663. . . . .

11.6.1 Displaying the Program Number and Sequence Number 663. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.6.2 Displaying the Status and W arning for Data Setting or Input/Output Operation 664. . . . . . . . . . . . . . . . . .

11.7 SCREENS DISPLAYED BY FUNCTION KEY

MESSAGE

11.7.1 External Operator Message History Display 666. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.8 CLEARING THE SCREEN 668. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.8.1 Erase Screen Display 668. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

11.8.2 Automatic Erase Screen Display 669. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.GRAPHICS FUNCTION 670. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.1 GRAPHICS DISPLAY 671. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.2 DYNAMIC GRAPHIC DISPLAY 677. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.2.1 Path Drawing 677. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.2.2 Solid Graphics 686. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

12.3 BACKGROUND DRAWING 697. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

658. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

666. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

c–8

B–63194EN/02

Table of Contents

13.HELP FUNCTION 699. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14.LASER FUNCTION 704. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14.1 LASER POWER SCREEN 705. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14.2 LASER SETTING SCREEN 706. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14.3 POWER COMPENSATION 709. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14.4 LASER POWER FEEDBACK 710. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14.5 NEAR–POINT SEARCH FUNCTION 711. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14.6 TRACING AXIS SWITCHING 713. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14.7 APPROACH FEED FUNCTION 714. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14.8 MANUAL OPERATION IN HAND COORDINATE SYSTEM 715. . . . . . . . . . . . . . . . . . . . . . . . . . . .

14.9 CUTTING CONDITION SETTING FUNCTION 717. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14.10 LASER STATUS SCREEN 721. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

14.11 THREE–VARIABLE TRANSFORM FUNCTION 722. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

IV. MAINTENANCE 723. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1. METHOD OF REPLACING BATTERY 725. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.1 REPLACING THE ALKALINE DRY CELLS (SIZE D) 727. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.2 USE OF ALKALINE DRY CELLS (SIZE D) 728. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

1.3 BATTERY FOR SEPARATE ABSOLUTE PULSE CODERS 729. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

APPENDIX

A. TAPE CODE LIST 733. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

B. LIST OF FUNCTIONS AND TAPE FORMAT 736. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

C. RANGE OF COMMAND VALUE 742. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

D. NOMOGRAPHS 745. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

D.1 BEAM PATH AT CORNER 746. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

D.2 RADIUS DIRECTION ERROR AT CIRCLE CUTTING 749. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

E. STATUS WHEN TURNING POWER ON, WHEN CLEAR

AND WHEN RESET 750. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

F. CHARACTER–TO–CODES CORRESPONDENCE TABLE 752. . . . . . . . . . . . . . . . . .

G. ALARM LIST 753. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

H. OPERATION OF PORTABLE TAPE READER 774. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

I. GLOSSARY 778. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

c–9

I. GENERAL

B–63194EN/02

GENERAL

About this manual

GENERAL

This manual consists of the following parts:

I. GENERAL

Describes chapter organization, applicable models, related manuals, and notes for reading this manual.

II. PROGRAMMING

Describes each function: Format used to program functions in the NC language, characteristics, and restrictions. When a program is created through conversational automatic programming function, refer to the manual for the conversational automatic programming function (Table 1).

III. OPERATION

Describes the manual operation and automatic operation of a machine, procedures for inputting and outputting data, and procedures for editing a program.

IV. MAINTENANCE

Describes procedures for replacing batteries.

APPENDIX

Lists tape codes, valid data ranges, and error codes.

1. GENERAL

Special symbols

Some functions described in this manual may not be applied to some products. For detail, refer to the DESCRIPTIONS manual(B–63192EN).

This manual does not describe parameters in detail. For details on parameters mentioned in this manual, refer to the manual for parameters (B–63200EN).

This manual describes all optional functions. Look up the options incorporated into your system in the manual written by the machine tool builder.

The models covered by this manual, and their abbreviations are:

Product name Abbreviations

FANUC Series 16i–LA 16i–LA Series 16i FANUC Series 160i–LA 160i–LA Series 160i

This manual uses the following symbols:

Indicates a combination of axes such as

X__ Y__ Z (used in PROGRAMMING.).

;

Indicates the end of a block. It actually corresponds to the ISO code LF or EIA code CR.

1. GENERAL

GENERAL

B–63194EN/02

Related manuals

The table below lists manuals related to Series 16i–LA, Series 160i–LA. In the table, this manual is marked with an asterisk (*).

Table 1 Related Manuals

Manual name

DESCRIPTIONS B–63002EN CONNECTION MANUAL (Hardware) B–63003EN CONNECTION MANUAL (Function) B–63003EN–1 P ARAMETER MANUAL B–63010EN FANUC Series 16i/160i–LA DESCRIPTIONS B–63192EN FANUC Series 16i/160i–LA CONNECTION MANUAL B–63193EN FANUC Series 16i/160i–LA OPERATOR’S MANUAL B–63194EN * FANUC Series 16i/160i–LA MAINTENANCE MANUAL B–63195EN FANUC Series 16i/160i–LA PARAMETER MANUAL B–63200EN PROGRAMMING MANUAL (Macro Compiler / Macro Executer) B–61803E–1

Specification

number

FAPT MACRO COMPILER PROGRAMMING MANUAL B–66102E

B–63194EN/02

GENERAL

1. GENERAL

1.1

GENERAL FLOW OF OPERATION OF CNC MACHINE TOOL

When machining the part using the CNC machine tool, first prepare the program, then operate the CNC machine by using the program.

1) First, prepare the program from a part drawing to operate the CNC machine tool. How to prepare the program is described in the Chapter II. PROGRAMMING.

2) The program is to be read into the CNC system. Then, mount the workpieces and tools on the machine, and operate the nozzle according to the programming. Finally, execute the machining actually. How to operate the CNC system is described in the Chapter III. OPERATION.

Part drawing

CHAPTER II PROGRAMMING CHAPTER III OPERATION

Part programming

CNC

MACHINE TOOL

Before the actual programming, make the machining plan for how to machine the part. Machining plan

1. Determination of workpieces machining range

2. Method of mounting workpieces on the machine tool

3. Machining sequence in every machining process

4. Cutting conditions

Cutting process

Cutting procedure

1. Cutting nozzle

2. Cutting conditions : Feedrate

3. Nozzle path

1 2

Feed cutting

Hole

machining

Hole cutting

Prepare the program of the nozzle path and cutting condition according to the workpiece figure, for each cutting.

1. GENERAL

1.2

GENERAL

B–63194EN/02

NOTES ON READING THIS MANUAL

NOTE

1 The function of an CNC machine tool system depends not

only on the CNC, but on the combination of the machine tool, its magnetic cabinet, the servo system, the CNC, the operator’s panels, etc. It is too difficult to describe the function, programming, and operation relating to all combinations. This manual generally describes these from the stand–point of the CNC. So, for details on a particular CNC machine tool, refer to the manual issued by the machine tool builder, which should take precedence over this manual.

2 Headings are placed in the left margin so that the reader can

easily access necessary information. When locating the necessary information, the reader can save time by searching though these headings.

3 Machining programs, parameters, variables, etc. are stored

in the CNC unit internal non–volatile memory. In general, these contents are not lost by the switching ON/OFF of the power. However, it is possible that a state can occur where precious data stored in the non–volatile memory has to be deleted, because of deletions from a maloperation, or by a failure restoration. In order to restore rapidly when this kind of mishap occurs, it is recommended that you create a copy of the various kinds of data beforehand.

4 This manual describes as many reasonable variations in

equipment usage as possible. It cannot address every combination of features, options and commands that should not be attempted. If a particular combination of operations is not described, it should not be attempted.

II. PROGRAMMING

B–63194EN/02

GENERAL

PROGRAMMING

1. GENERAL

PROGRAMMING

B–63194EN/02

1.1 NOZZLE MOVEMENT ALONG WORKPIECE P ARTS FIGURE– INTERPOLATION

Explanations

D Nozzle movement along

a straight line

The nozzle moves along straight lines and arcs constituting the workpiece parts figure (See II–4).

The function of moving the nozzle along straight lines and arcs is called the interpolation.

Program G01 Y__; X__Y__ ;

Workpiece

Nozzle

D Nozzle movement along

an arc

Fig.1.1 (a) Nozzle movement along a straight line

Program G03X_ _Y_ _R_ _;

Workpiece

Nozzle

Fig. 1.1 (b) Nozzle movement along an arc

+ 789 hidden pages