fanuc 16B, 160B, 18B, 180- B Maintenance Manual

FANUC Series 16/160/18/180 –Model B
MAINTENANCE MANUAL
B-62445E/03
No part of this manual may be reproduced in any form.
All specifications and designs are subject to change without notice.
The export of this product is subject to the authorization of the government of the country from where the product is exported.
In this manual we have tried as much as possible to describe all the various matters. However, we cannot describe all the matters which must not be done, or which cannot be done, because there are so many possibilities. Therefore, matters which are not especially described as possible in this manual should be regarded as ”impossible”.
This manual contains the program names or device names of other companies, some of which are registered trademarks of respective owners. However, these names are not followed by or in the main body.
B–62445E/03

PREFACE

PREFACE
Description of this manual
1.CRT/MDI display and operation
This chapter covers those items, displayed on the CR T , that are related to maintenance. A list of all supported operations is also provided at the end of this chapter.
2.Hardware
This chapter covers hardware–related items, including the hardware configuration, connection, and NC status indicated on printed circuit boards. A list of all units is also provided as well as an explanation of how to replace each unit.
3. Data input/output
This chapter describes the input/output of data, including programs, parameters, and tool compensation data, aswell as the input/output procedures for conversational data.
4.Interface between the NC and PMC
This chapter describes the PMC specifications, the system configuration, and the signals used by the PMC.
5.Digital servo
This chapter describes the servo tuning screen and how to adjust the reference position return position.
6.and 7. AC spindles
These chapters describe the spindle amplifier checkpoints, as well as the spindle tuning screen.
8. Trouble shooting
This chapter describes the procedures to be followed in the event of certain problems occurring, for example, if the power cannot be turned on or if manual operation cannot be performed. Countermeasures to be applied in the event of alarms being output are also described.
9. and 10. Spindle trouble shooting
These chapters explain the alarms related to spindles, as well as the corresponding countermeasures to be applied.
APPENDIX
The appendix consists of a list of all alarms, as well as a list of maintenance parts. The I/O Unit–MODEL A is also described. This manual does not provide a parameter list. If necessary, refer to the separate PARAMETER DESCRIPTIONS (B–61810E) . This manual describes all optional functions. Refer to the manual provided by the machine tool builder for details of any options with which the installed machine tool is provided.
PREFACE
T series (two–path
ries (two–path
T series (two–path
M series
B–62445E/03
This manual can be used with the following models. The abbreviated names may be used.

Applicable models

Pruduct name Abbreviation
FANUC Series 16–TB 16–TB FANUC Series 160–TB 160–TB FANUC Series 16–MB 16–MB FANUC Series 160–MB 160–MB FANUC Series 18–TB 18–TB FANUC Series 180–TB 180–TB FANUC Series 18–MB 18–MB FANUC Series 180–MB 180–MB
T series or
control)*
M series or M se-
control)*
T series or
control)*
Note
Some function described in this manual may not be applied to some products. For details, refer to the DESCRIPTIONS manual (B–62442E)
1
1
1

Related manuals

The table below lists manuals related to MODEL B of Series 16, Series 18, Series 160 and Series 180. In the table, this manual is marked with an asterisk(*).
Table 1 Manuals Related
Manual name Specification
number
DESCRIPTIONS B–62442E CONNECTION MANUAL (HARDWARE) B–62443E CONNECTION MANUAL (FUNCTION) B–62443E–1 OPERATOR’S MANUAL FOR LATHE B–62444E OPERATOR’S MANUAL FOR MACHINING B–62454E MAINTENANCE MANUAL B–62445E * PARAMETER MANUAL B–62450E PROGRAMMING MANUAL (Macro Compiler / Macro Execu-
ter)
FAPT MACRO COMPILER PROGRAMMING MANUAL B–66102E FANUC Super CAP T OPERATOR’S MANUAL B–62444E–1
B–61803E–1
FANUC Super CAP M OPERATOR’S MANUAL B–62154E FANUC Super CAP M PROGRAMMING MANUAL B–62153E
B–62445E/03
PREFACE
Table 1 Manuals Related
Manual name Specification
number
CONVERSATIONAL AUTOMATIC PROGRAMMING FUNC­TION I FOR LATHE (Series 18–TB) OPERATOR’S MANUAL
CONVERSATIONAL AUTOMATIC PROGRAMMING FUNC­TION II FOR LATHE (Series 15–MODEL B, Series–16 CAP II) OPERATOR’S MANUAL
For specifications and maintenance of FANUC CONTROL MOTOR α series, refer to the following manuals :
Document name
FANUC AC SERVO MOTOR α series DESCRIPTIONS
FANUC AC SPINDLE MOTOR α series DESCRIPTIONS
FANUC CONTROL MOTOR AMPLIFIER α series DESCRIPTIONS
Document
number
B–65142E
B–65152E
B–65162E
Major contents Major usage
SpecificationCharacteristicsExternal dimensionsConnections
Specification
Selection of motorConnection of motor
CharacteristicsExternal dimensionsConnections
Specifications and
functions
InstallationExternal dimensions and
maintenance area
Selection of
amplifier
Connection of
amplifier
Connections
B–61804E–1
B–61804E–2
FANUC CONTROL MOTOR α series MAINTENANCE MANUAL
FANUC AC SERVO MOTOR α series PARAMETER MANUAL
FANUC AC SPINDLE MOTOR α series PARAMETER MANUAL
B–65165E
B–65150E
B–65160E
Start up procedureTroubleshootingMaintenance of motor
Initial settingSetting parametersDescription of parameters
Initial settingSetting parametersDescription of parameters
Start up the system
(Hardware)
TroubleshootingMaintenance of
motor
Start up the system
(Software)
Turning the system
(Parameters)
B–62445E/03

Table of Contents

1. DISPLAY AND OPERATION OF CRT/MDI 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1 FUNCTION KEYS AND SOFT KEYS 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.1.1 Soft Keys 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2 SCREEN DISPLAYED IMMEDIATELY AFTER POWER IS TURNED ON 22. . . . . . . . . . . . . . . . . .
1.2.1 Slot Status Display 22. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.2 Setting Module Screen 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.2.3 Configuration Display of Software 23. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3 SYSTEM CONFIGURATION SCREEN 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.1 Display Method 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.2 Configuration of PCBs 24. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.3 Software Configuration Screen 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.3.4 Module Configuration Screen 26. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4 ALARM HISTORY SCREEN 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4.1 General 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4.2 Screen Display 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4.3 Clearing Alarm History 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.4.4 Alarm Display 27. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.5 EXTERNAL OPERATOR MESSAGES RECORD 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.5.1 Screen Display 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.5.2 Deletion of External Operator Messages Record 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.5.3 Parameter 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.5.4 Notes 29. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.6 OPERATION HISTORY 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.6.1 Parameter Setting 30. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.6.2 Screen Display 31. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.6.3 Setting the Input Signal or Output Signal to be Recorded in the Operation History 35. . . . . . . . . . . . . . . . . .
1.6.4 Inputting and Outputting the Operation History Data 44. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.6.5 Notes 50. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.7 HELP FUNCTION 51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.7.1 General 51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.7.2 Display Method 51. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.8 DISPLAYING DIAGNOSTIC PAGE 54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.8.1 Displaying Diagnostic Page 54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.8.2 Contents Displayed 54. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.9 NC STATE DISPLAY 68. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.10 WAVE FORM DIAGNOSTIC FUNCTION 69. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.10.1 Setting Parameters 69. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.10.2 Waveform Diagnostic Parameter Screen 70. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.10.3 Graphic of Wave Diagnosis Data 73. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.10.4 Data Sampling for Storage Type Waveform Diagnosis 75. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.10.5 Outputting Waveform Diagnosis Data (Storage Type) 77. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.11 OPERATING MONITOR 80. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.11.1 Display Method 80. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.12 LIST OF OPERATIONS 82. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.13 WARNING SCREEN DISPLAYED WHEN AN OPTION IS CHANGED 86. . . . . . . . . . . . . . . . . . . . .
1.14 WARNING SCREEN DISPLAYED WHEN SYSTEM SOFTW ARE IS REPLACED
(SYSTEM LABEL CHECK ERROR) 88. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2. HARDWARE 89. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.1 STRUCTURE 90. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
c–1
T ABLE OF CONTENTS
B–62445E/03
2.2 GENERAL OF HARDWARE 91. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.2.1 Series 16 91. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3 TOTAL CONNECTION DIAGRAM 92. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3.1 16–TB/MB, 160–TB/MB (MAIN–A SPEC.) 93. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3.2 16–TB/MB, 160–TB/MB, 18–TB/MB, 180–TB/MB (MAIN–B SPEC.) 95. . . . . . . . . . . . . . . . . . . . . . . . . . .
2.3.3 18–TB/MB 97. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4 INTER–MACHINE CONNECTION 99. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.1 CRT/MDI Unit 99. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.2 Reader/Puncher Interface 101. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.3 Manual Pulse Generator 102. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.4 I/O LINK 103. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.5 Servo Interface 105. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.6 Connections by Type of Detectors 109. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.7 Combining Serial Spindle and Analog Spindle 112. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.8 Connection to
2.4.9 Connection to Serial Spindle Amplifier 114. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.10 Connection to Analog Spindle Amplifier 115. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.11 Remote Buffer Interface 115. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.12 High–speed DI Signal Interface 117. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.13 Analog Signal Interface 119. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.14 Environmental Requirement 120. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.15 Power Capacity 120. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.4.16 Action Against Noise 120. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
α serial Spindle Amplifier 113. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5 LED DISPLAY AND MODULE CONFIGURA TION OF PCB 126. . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5.1 Power Supply Unit 126. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5.2 Main CPU Board 130. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5.3 Option 1 Board 140. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5.4 Option 2 Board 142. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5.5 Option 3 Board 148. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5.6 Loader Control Boad 151. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5.7 I/O Card (Sink Type Output) 154. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5.8 I/O Card (Source Type Output) 154. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5.9 I/O Cards with Power Supply (Power C) (Sink Type Output) 155. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5.10 I/O Cards with Power Supply (Power C) (Source Type Output) 157. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.5.11 Background Graphic Board 159. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.6 LIST OF THE PCBS AND UNITS 161. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.6.1 Control Unit Rack 161. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.6.2 Power Unit 162. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.6.3 Control Unit P.C.B. 162. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.6.4 Modules 164. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.6.5 CRT/MDI Unit 166. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7 HOW TO REPLACE THE MODULES 172. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7.1 Removing 172. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.7.2 Insertion 172. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.8 HOW TO REPLACE THE BATTERIES 173. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.8.1 Replace the Battery for Memory Back Up 173. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.8.2 Replacing Batteries for Separate Absolute Pulse Coder 174. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.9 HOW TO REPLACE FAN MOTOR 175. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.10 FUSE REPLACEMENT IN POWER SUPPLY UNIT 176. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.11 MAINTENANCE OF HEAT PIPE TYPE HEAT EXCHANGER 177. . . . . . . . . . . . . . . . . . . . . . . . . . .
c–2
B–62445E/03
T ABLE OF CONTENTS
2.12 HOW TO REPLACE THE COLOR LIQUID CRYSTAL DISPLAY 180. . . . . . . . . . . . . . . . . . . . . . . . .
2.13 REPLACING THE LCD FUSE 181. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2.14 REPLACING THE LCD BAKLIGHT 182. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3. INPUT AND OUTPUT OF DATA 183. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.1 SETTING P ARAMETERS FOR INPUT/OUTPUT 184. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2 INPUTTING/ OUTPUTTING DATA 186. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.1 Confirming the Parameters Required for Data Output 186. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.2 Outputting CNC Parameters 187. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.3 Outputting PMC Parameters 188. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.4 Outputting Pitch Error Compensation Amount 188. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.5 Outputting Custom Macro Variable Values 189. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.6 Outputting Tool Compensation Amount 189. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.7 Outputting Part Program 190. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.8 Inputting CNC Parameters 190. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.9 Inputting PMC Parameters 192. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.10 Inputting Pitch Error Compensation Amount 192. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.11 Inputting Custom Macro Variable Values 193. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.12 Inputting Tool Compensation Amount 193. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.2.13 Inputting Part Programs 194. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3 INPUT/OUTPUT SUPER CAP DAT A 195. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.1 Input/Output of Conversational Data in a Lump(Super CAP M) 195. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.2 Input and Output of Each File 197. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.3 Output of CAP Data (Super CAP T) 197. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.3.4 Inputting CAP Data (Super CAP T) 202. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.4 INPUTTING/OUTPUTT ING CAP–II DATA(16–T) 205. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5 DUMP/RESTORE OF CAP–II DATA (16 – T) 207. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.1 Kind of Data in Sub Memory 207. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.5.2 Operation 207. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.6 CLEARING CAP–II DATA (16 – T) 208. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.6.1 Deleting File Name and Files 208. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3.6.2 Clearing CAP–II Memory 209. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4. INTERFACE BETWEEN NC AND PMC 210. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.1 GENERAL OF INTERFACE 211. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2 SPECIFICATION OF PMC 212. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.1 Specification 212. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.2 Address 213. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.3 Built–in Debug Function 214. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.4 System Reserve Area of Internal Relay 214. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.5 Execution Period of PMC 217. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3 PMC SCREEN 218. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.1 Display Method 218. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2 PMCLAD Screen 219. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.3 PMCDGN Screen 223. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.4 Memory Display (M.SRCH) 227. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.5 PMCRAM Screen 231. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.4 LIST OF SIGNALS BY EACH MODE 237. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.5 SIGNAL AND SYMBOL CORRESPONDENCE TABLE 239. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
c–3
T ABLE OF CONTENTS
B–62445E/03
5. DIGITAL SERVO 247. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1 INITIAL SETTING SERVO PARAMETERS 248. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2 SERVO TUNING SCREEN 253. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2.1 Parameter Setting 253. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2.2 Displaying Servo Tuning Screen 253. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3 ADJUSTING REFERENCE POSITION (DOG METHOD) 256. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3.1 General 256. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4 DOGLESS REFERENCE POSITION SETTING 258. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4.1 General 258. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4.2 Operation 258. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4.3 Associated Parameters 259. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6. AC SPINDLE (SERIAL INTERFACE) 260. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1 GENERAL OF SPINDLE CONTROL (SERIAL* INTERFACE) 261. . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1.1 Method A of Gear Change for Machining Center 262. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1.2 Method B of Gear Change for Machining Center(PRM 3705#2=1) 262. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1.3 For Lathe 262. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2 TABLE OF TEST POINTS 263. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.1 Printed Circuit Board (A16B–2201–0440) 263. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.2 Signal Waveform At Test Points 265. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3 CONFIRMING POWER SUPPLY (SERIAL INTERF ACE) 266. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3.1 Power Supply 266. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3.2 Test Points 266. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4 SPINDLE SETTING AND TUNING SCREEN 269. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4.1 Display Method 269. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4.2 Spindle Setting Screen 269. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4.3 Spindle Tuning Screen 270. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4.4 Spindle Monitor Screen 272. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4.5 Correspondence Between Operation Mode and Parameters on Spindle Tuning Screen 274. . . . . . . . . . . . . . .
6.5 AUTOMATIC SETTING OF STANDARD PARAMETER 277. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7. AC SPINDLE (ANALOG INTERFACE) 278. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1 GENERAL OF SPINDLE CONTROL (ANALOG INTERFACE) 279. . . . . . . . . . . . . . . . . . . . . . . . . .
7.1.1 Block Diagram 279. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1.2 Calculation of S Analog Voltage and Associated Parameters 280. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1.3 Tuning S Analog Voltage (D/A Converter) 282. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2 TABLE OF TEST POINTS 284. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.1 Model 1S to 3S (Amp. Specification : A06B–6059–H00x) 284. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.2 Models 6S to 26S (Amp. specification: A06B–6059–H2xx) 285. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.2.3 Test Points Signal Waveform 286. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.3 SETTING PARAMETERS (DIGITAL AC SPINDLE) 287. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.4 SETTING STANDARD PARAMETERS 288. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.5 LIST OF PARAMETER 289. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.6 TUNING AFTER REPLACING PCB (S SERIES AC SPINDLE) 292. . . . . . . . . . . . . . . . . . . . . . . . . .
8. TROUBLESHOOTING 294. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1 CORRECTIVE ACTION FOR FAILURES 296. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.1.1 Investigating the Conditions under which Failure Occurred 296. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
c–4
B–62445E/03
8.2 POWER CANNOT BE TURNED ON 298. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.3 NO MANUAL OPERATION NOR AUTOMATIC OPERATION CAN BE EXECUTED 301. . . . . . . .
8.4 JOG OPERATION CANNOT BE DONE 305. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.5 HANDLE OPERATION CANNOT BE DONE 309. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.6 AUTOMATIC OPERATION CANNOT BE DONE 312. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.7 CYCLE START LED SIGNAL HAS TURNED OFF 321. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.8 NOTHING IS DISPLAYED ON CRT 323. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.9 ALARM 85 TO 87 (READER/PUNCHER INTERFACE ALARM) 326. . . . . . . . . . . . . . . . . . . . . . . . .
8.10 REFERENCE POSITION DEVIATES 335. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.11 ALARM 90 (REFERENCE POSITION RETURN IS ABNORMAL) 336. . . . . . . . . . . . . . . . . . . . . . . .
8.12 ALARM 300 (REQUEST FOR REFERENCE POSITION RETURN) 338. . . . . . . . . . . . . . . . . . . . . . .
8.13 ALARM 301 TO 305 (ABSOLUTE PULSE CODER IS FAULTY) 339. . . . . . . . . . . . . . . . . . . . . . . . .
8.14 ALARM 306 TO 308 (ABSOLUTE PULSE CODER BATTERY IS LOW) 342. . . . . . . . . . . . . . . . . . .
8.15 ALARM 350 (SERIAL PULSE CODER IS ABNORMAL) 343. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.16 ALARM 351 (SERIAL PULSE CODER COMMUNICATION IS ABNORMAL) 344. . . . . . . . . . . . . .
8.17 ALARM 400 (OVERLOAD) 345. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.18 ALARM 401 (*DRDY SIGNAL TURNED OFF) 347. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.19 ALARM 404 AND 405 (*DRDY SIGNAL TURNED ON) 349. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.20 ALARM 410 (EXCESSIVE POSITION ERROR AMOUNT DURING STOP) 350. . . . . . . . . . . . . . . .
8.21 ALRAM 411 (EXECESSIVE POSITION ERROR DURING MOVE) 351. . . . . . . . . . . . . . . . . . . . . . .
8.22 ALARM 414 (DIGITAL SERVO SYSTEM IS ABNORMAL) 353. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.23 ALRAM 416 (DISCONNECTION ALARM) 365. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.24 ALARM 417 (DIGITAL SERVO SYSTEM IS ABNORMAL) 366. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.25 ALARM 700 (OVERHEAT AT CONTROL SIDE) 367. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.26 ALARM 704 (SPINDLE SPEED FLUCTUATION DETECTION ALARM) 368. . . . . . . . . . . . . . . . . .
8.27 ALARM 749 (SERIAL SPINDLE COMMUNICATION ERROR) 369. . . . . . . . . . . . . . . . . . . . . . . . . .
8.28 ALARM 750 (SPINDLE SERIAL LINK CANNOT BE STARTED) 372. . . . . . . . . . . . . . . . . . . . . . . .
8.29 ALARM 751,761 (SPINDLE ALARM) 377. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.30 ALARM 900 (ROM PARITY ERROR) 378. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.31 ALARM 910 TO 915 (SRAM PARITY) 381. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.32 ALARM 916 (DRAM PARITY ERROR) 384. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.33 ALARM 920 TO 923 (WATCH DOG OR RAM PARITY) 386. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.34 ALARM 924 (SERVO MODULE MOUNTING ERROR) 390. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.35 ALARM 930 (CPU ERROR) 391. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.36 ALARM 950 (PMC SYSTEM ALARM) 392. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.37 ALARM 951 (PMC–RCWATCH DOG ALARM) 394. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.38 ALARM 970 (NMI ALARM IN PMC CONTROL MODULE) 395. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.39 ALARM 971 (NMI ALARM IN SLC) 397. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.40 ALARM 972 (NMI ALARM) 398. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8.41 ALARM 973 (NMI ALARM BY UNKNOWN CAUSE) 399. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
T ABLE OF CONTENTS
9. TROUBLESHOOTING (SERIAL INTERFACE SPINDLE) 400. . . . . . . . . . . . . . . . . . . . . . .
9.1 LIST OF SERIAL INTERFACE SPINDLE AMPLIFIER ALARMS 401. . . . . . . . . . . . . . . . . . . . . . . .
9.2 TROUBLESHOOTING FOR EACH ALARM 404. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10. TROUBLESHOOTING (ANALOG INTERFACE SPINDLE) 411. . . . . . . . . . . . . . . . . . . . .
10.1 AL–01 (MOTOR OVERHEAT) 412. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
c–5
T ABLE OF CONTENTS
10.2 AL–02 (EXCESSIVE DEVIATION OF SPEED) 413. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.3 AL–06, 07 (OVER SPEED) 414. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.4 AL–09 (UNIT OVERHEAT / 6S TO 26S ONLY) 415. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.5 AL–10 (LOW INPUT VOLTAGE) 416. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.6 AL–11 (DC LINK EXCESSIVE VOLTAGE) 417. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.7 AL–12 (DC LINK EXCESSIVE CURRENT) 418. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.8 ABNORMAL SOUND AND VIBRATION DURING ROTATION 419. . . . . . . . . . . . . . . . . . . . . . . . . .
10.9 NO ROTA TION OR INCORRECT SPEED 420. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.10 CONFIRMATION OF TRANSISTOR MODULE 421. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B–62445E/03
APPENDIXES
A. I/O UNIT MODEL A 425. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.1 SYSTEM CONFIGURATION 426. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.2 HARDWARE CONFIGURATION 426. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.3 LED INDICATION 427. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.4 FUSES 428. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
A.5 REMOVING A PRINTED CIRCUIT BOARD 429. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B. ALARM LIST 431. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.1 LIST OF ALARM CODES 432. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.2 LIST OF ALARMS (PMC) 456. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.3 SPINDLE ALARMS (SERIAL SPINDLE) 463. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
B.4 SPINDLE ALARMS (ANALOG INTERFACE) (S SEIRES AC SPINDLE) 468. . . . . . . . . . . . . . . . . .
C. LIST OF MAINTENANCE PARTS 471. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
C.1 MAINTENANCE PARTS 472. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D. BOOT SYSTEM 487. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D.1 OVER VIEW 488. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D.1.1 Starting the Boot System 488. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D.1.2 System Files and User Files 489. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D.1.3 Boot Slot Configuration Screen 489. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D.2 SCREEN CONFIGURATION AND OPERATING PROCEDURE 490. . . . . . . . . . . . . . . . . . . . . . . . . .
D.2.1 System Data Loading Screen 491. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D.2.2 System Data Check Screen 493. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D.2.3 System Data Delete Screen 495. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D.2.4 System Data Save Screen 496. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D.2.5 SRAM Data Backup Screen 498. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D.2.6 Memory Card File Delete Screen 501. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D.2.7 Memory Card Format Function 502. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D.2.8 Load Basic System Function 503. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
D.3 ERROR MESSAGES AND REQUIRED ACTIONS 504. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
E. NOTATION OF MDI KEYS 506. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
c–6
B–62445E/03
1
1. DISPLA Y AND OPERATION OF CRT/MDI

DISPLAY AND OPERATION OF CRT/MDI

This chapter describes how to display various screens by the function keys. The screens used for maintenance are respectively displayed.
1.1 FUNCTION KEYS AND SOFT KEYS 2. . . . . . . . . . .
1.2 SCREEN DISPLAYED IMMEDIATELY AFTER
POWER IS TURNED ON 22. . . . . . . . . . . . . . . . . . . . .
1.3 SYSTEM CONFIGURATION SCREEN 24. . . . . . . . .
1.4 ALARM HISTORY SCREEN 27. . . . . . . . . . . . . . . . . .
1.5 EXTERNAL OPERATOR MESSAGES
RECORD 28. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.6 OPERATION HISTORY 30. . . . . . . . . . . . . . . . . . . . . .
1.7 HELP FUNCTION 51. . . . . . . . . . . . . . . . . . . . . . . . . . .
1.8 DISPLAYING DIAGNOSTIC PAGE 54. . . . . . . . . . . .
1.9 NC STATE DISPLAY 68. . . . . . . . . . . . . . . . . . . . . . . .
1.10 WAVE FORM DIAGNOSTIC FUNCTION 69. . . . . . .
1.11 OPERATING MONITOR 80. . . . . . . . . . . . . . . . . . . . .
1.12 LIST OF OPERATIONS 82. . . . . . . . . . . . . . . . . . . . . .
1.13 WARNING SCREEN DISPLAYED WHEN
AN OPTION IS CHANGED 86. . . . . . . . . . . . . . . . . . .
1.14 WARNING SCREEN DISPLAYED WHEN SYSTEM SOFTWARE IS REPLACED
(SYSTEM LABEL CHECK ERROR) 88. . . . . . . . . . .
1
1. DISPLA Y AND OPERATION OF CRT/MDI
B–62445E/03
1.1

FUNCTION KEYS AND SOFT KEYS

1.1.1
Soft Keys
Operations and soft key display staturs for each function key are described below:
T o display a more detailed screen, press a function key followed by a soft key. Soft keys are also used for actual operations. The following illustrates how soft key displays are changed by pressing each function key.
The symbols in the following figures mean as shown below :
: Indicates screens




: Indicates a screen that can be displayed by pressing a
: Indicates a soft key(*2)
: Indicates input from the MDI panel.
: Indicates a soft key displayed in green (or highlighted).
: Indicates the continuous menu key (rightmost soft key)(*3).
function key(*1)
*1 Press function keys to switch between screens that are used frequently.
*2 Some soft keys are not displayed depending on the option configuration.
*3 In some cases, the continuous menu key is omitted when the 14 CRT
display or 8.4/9.5/LCD is used.
2
B–62445E/03
1. DISPLA Y AND OPERATION OF CRT/MDI
POSITION SCREEN
POS
Absolute coordinate display
[ABS]
Relative coordinate display
[REL]
Current position display
[(OPRT)]
[(OPRT)]
Soft key transition triggered by the function key
[PTSPRE] [EXEC] [RUNPRE] [EXEC]
(Axis or numeral)
[ORIGIN]
[PTSPRE] [EXEC] [RUNPRE] [EXEC]
[ALLEXE] [Axis name] [EXEC]
[PRESET]
POS
[ALL]
[(OPRT)]
Handle interruption
[HNDL]
Monitor screen
[MONI]
[(OPRT)]
[(OPRT)]
(Axis or numeral)
[ORIGIN]
[PTSPRE] [EXEC] [RUNPRE] [EXEC]
[PTSPRE] [EXEC] [RUNPRE] [EXEC]
[PTSPRE] [EXEC] [RUNPRE] [EXEC]
[ALLEXE] [Axis name] [EXEC]
[PRESET]
3
1. DISPLA Y AND OPERATION OF CRT/MDI
B–62445E/03
PROGRAM SCREEN
PROG
Program display screen
[PRGRM]
(1)
Program check display screen
[CHECK]
[(OPRT)]
[ABS] [REL]
Soft key transition triggered by the function key in the MEM mode
[BG–EDT [O number] [N number] [REWIND]
[P TYPE [Q TYPE]
[F SRH]
[(OPRT)]
]
]
See"When the soft key [BG-EDT] is pressed"
[O SRH] [N SRH]
[CAN] [EXEC
]
[BG–EDT [O number] [N number] [REWIND]
]
See"When the soft key [BG-EDT] is pressed"
[O SRH] [N SRH]
PROG
1/2
Current block display screen
[(OPRT)]
Next block display screen
[(OPRT)]
Program restart display screen
[(OPRT)]
(2)(Continued on the next page)
[BG–EDT][CURRNT]
[BG–EDT
[BG–EDT
][NEXT]
][RSTR]
[P TYPE [Q TYPE]
[F SRH]
]
[CAN] [EXEC
]
See"When the soft key [BG-EDT] is pressed"
See"When the soft key [BG-EDT] is pressed"
See"When the soft key [BG-EDT] is pressed"
4
B–62445E/03
1. DISPLA Y AND OPERATION OF CRT/MDI
(2)
[FL.SDL] [PRGRM]
Return to (1) (Program display)
File directory display screen
[(OPRT)][DIR] [SELECT]
Schedule operation display screen
[SCHDUL] [CLEAR]
[(OPRT)]
(Schedule data)
[File No. ]
[EXEC]
[CAN] [EXEC
2/2
[F SET]
]
[INPUT]
5
1. DISPLA Y AND OPERATION OF CRT/MDI
B–62445E/03
PROGRAM SCREEN
PROG
Program display
[PRGRM]
[(OPRT)]
Soft key transition triggered by the function key in the EDIT mode
[BG–EDT (O number) (Address) [SRH] (Address) [SRH] [REWIND]
[F SRH] [CAN]
[READ] [CHAIN]
[PUNCH] [STOP]
[DELETE] [CAN]
[EX–EDT] [COPY] [CRSR – ]
]
See"When the soft key [BG-EDT] is pressed"
[O SRH]
(N number) [EXEC]
(The cursor moves to the end of a program.)
[STOP] [CAN]
(O number)
[CAN] (O number)
(N number)
[MOVE] [CRSR]
[MERGE] [ – CRSR]
[CHANGE] (Address) [BEFORE]
[EXEC]
[EXEC]
[EXEC]
[ – CRSR] [ – BTTM] [ALL]
[ – CRSR] [ – BTTM] [ALL]
[ – BTTM]
(O number) [EXEC]
(O number) [EXEC]
(O number) [EXEC]
PROG
1/2
(1)(Continued on the next page)
(Address)
[AFTER] [SKIP]
[1–EXEC] [EXEC]
6
B–62445E/03
1. DISPLA Y AND OPERATION OF CRT/MDI
(1)
Program directory display
[LIB]
Graphic Conversational Programming (T series)
[C.A.P.]
[(OPRT)]
[PRGRM] [G.MENU]
(G number)
When a G number is omitted, the standard screen appears.
[BG–EDT (O number)
[READ] [CHAIN]
[PUNCH] [STOP]
]
Return to the program
[BLOCK] (Data)
See"When the soft key [BG-EDT] is pressed"
[O SRH]
[STOP] [CAN] (O number)
[CAN] (O number)
Return to the program
[EXEC]
[EXEC]
[LINE] [CHAMF] [CNR.R] [INPUT]
2/2
Graphic Conversational Programming (M series)
[C.A.P.]
Floppy directory display
[FLOPPY]
[PRGRM] [G.MENU]
[(OPRT)]
(G number)
When a G number is omitted, the standard screen appears.
[PRGRM] [DIR] (Numeral)
Return to the program
[BLOCK] (Data) [INPUT]
[INPUT]
Return to the program
[(OPRT)]
[F SRH]
[READ]
[PUNCH]
[DELETE]
[CAN] [EXEC] (Numeral) (Numeral) [STOP] [CAN] [EXEC] (Numeral) (Numeral) [STOP] [CAN] [EXEC] (Numeral) [CAN] [EXEC]
INSERT
[F SET]
[F SET] [O SET]
[F SET] [O SET]
[F SET]
7
1. DISPLA Y AND OPERATION OF CRT/MDI
B–62445E/03
PROGRAM SCREEN
PROG
Program display
Program input screen
Current block display screen
[(OPRT)]
[(OPRT)]
[(OPRT)]
Soft key transition triggered by the function key in the MDI mode
[BG–EDT
[BG–EDT][MDI] [START]
(Address) (Address) [REWIND]
][PRGRM]
See"When the soft key [BG-EDT] is pressed"
See"When the soft key [BG-EDT] is pressed"
[CAN] [EXEC
] [SRH] [SRH]
[BG–EDT][CURRNT]
See"When the soft key [BG-EDT] is pressed"
PROG
Next block display screen
[(OPRT)]
Program restart display screen
[(OPRT)]
[BG–EDT][NEXT]
[BG–EDT
See"When the soft key [BG-EDT] is pressed"
][RSTR]
See"When the soft key [BG-EDT] is pressed"
8
B–62445E/03
1. DISPLA Y AND OPERATION OF CRT/MDI
PROGRAM SCREEN
PROG
Program display
Current block display screen
Next block display screen
Program restart display screen
[(OPRT)]
[(OPRT)]
[(OPRT)]
Soft key transition triggered by the function key in the HNDL, JOG, or REF mode
[BG–EDT
[BG–EDT][NEXT]
][PRGRM]
[BG–EDT][CURRNT]
See"When the soft key [BG-EDT] is pressed"
See"When the soft key [BG-EDT] is pressed"
See "When the soft key [BG-EDT] is pressed"
PROG
[(OPRT)]
[BG–EDT
][RSTR]
See"When the soft key [BG-EDT] is pressed"
9
1. DISPLA Y AND OPERATION OF CRT/MDI
B–62445E/03
PROGRAM SCREEN
PROG
Program display
Program input screen
Program directory display
[LIB]
[(OPRT)]
[(OPRT)]
[(OPRT)]
Soft key transition triggered by the function key in the TJOG or THDL mode
[BG–EDT
[BG–EDT (O number) (Address) (Address) [REWIND]
[BG–EDT (O number)
][PRGRM]
][MDI]
]
See "When the soft key [BG-EDT] is pressed"
See "When the soft key [BG-EDT] is pressed"
[O SRH] Return to the program [SRH] [SRH]
See "When the soft key [BG-EDT] is pressed"
[O SRH]
Return to the program
PROG
10
B–62445E/03
1. DISPLA Y AND OPERATION OF CRT/MDI
PROGRAM SCREEN
PROG
Program display
[PRGRM]
[(OPRT)]
Soft key transition triggered by the function key (When the soft key [BG–EDT] is pressed in all modes)
[BG–END (O number) (Address) [SRH] (Address) [SRH] [REWIND]
[F SRH] [CAN]
[READ] [CHAIN]
[PUNCH] [STOP]
[DELETE] [CAN]
[EX–EDT] [COPY] [CRSR – ]
]
[O SRH]
(N number) [EXEC]
(The cursor moves to the end of a program.)
[STOP] [CAN]
(O number)
[CAN]
(O number)
(N number)
[MOVE] [CRSR – ]
[MERGE] [ – CRSR]
[CHANGE] (Address) [BEFORE]
[EXEC]
[EXEC]
[EXEC]
[ – CRSR] [ – BTTM] [ALL]
[ – CRSR] [ – BTTM] [ALL]
[ – BTTM]
(O number) [EXEC]
(O number) [EXEC]
(O number) [EXEC]
PROG
1/2
(1)(Continued on the next page)
11
(Address)
[AFTER] [SKIP]
[1–EXEC] [EXEC]
1. DISPLA Y AND OPERATION OF CRT/MDI
B–62445E/03
(1)
Program directory display
[LIB]
Graphic Conversational Programming
[C.A.P.]
[(OPRT)]
[PRGRM] [G.MENU]
(G number)
When a G number is omitted, the standard screen appears.
[BG–EDT] (O number)
[READ] [CHAIN]
[PUNCH] [STOP]
[O SRH]
[STOP] [CAN]
(O number)
[CAN]
(O number)
Return to the program
[BLOCK] (Data)
2/2
Return to the program
[EXEC]
[EXEC]
[LINE] [CHAMF] [CNR.R] [INPUT]
Floppy directory display
[FLOPPY]
[PRGRM] [DIR]
Return to the program
[(OPRT)]
[F SRH]
[READ]
[PUNCH]
[DELETE]
(Numeral) [CAN] [EXEC]
(Numeral)
(Numeral) [STOP] [CAN] [EXEC]
(Numeral)
(Numeral) [STOP] [CAN] [EXEC]
(Numeral) [CAN] [EXEC]
[F SET]
[F SET] [O SET]
[F SET] [O SET]
[F SET]
12
B–62445E/03
1. DISPLA Y AND OPERATION OF CRT/MDI
OFFSET/SETTING SCREEN (T series)
OFFSET SETTING
Tool offset screen
[OFFSET]
[WEAR] [GEOM]
[(OPRT)]
Soft key transition triggered by the function key
(Number) (Axis name and numeral) [MEASUR] (Axis name) (Numeral) (Numeral)
[CLEAR] [ALL]
[READ] [CAN]
[PUNCH] [CAN]
OFFSET
SETTING
[NO SRH]
[INP.C.] [+INPUT] [INPUT]
[WEAR] [GEOM]
[EXEC
[EXEC
]
]
1/2
Setting screen
[SETING]
Work coordinate system setting screen
[WORK]
Macro variables display screen
[MACRO]
[(OPRT)]
[(OPRT)]
[(OPRT)
(Number) (Axis name and numeral) [MEASUR] (Numeral) (Numeral)
]
(Number) [ON:1] [OFF:0] (Numeral) (Numeral)
(Number) (Axis name) [INP.C.] (Numeral)
[PUNCH]
[NO SRH]
[+INPUT] [INPUT]
[NO SRH]
[+INPUT] [INPUT]
[NO SRH]
[INPUT]
[CAN] [EXEC
]
(1)(Continued on the next page)
13
1. DISPLA Y AND OPERATION OF CRT/MDI
B–62445E/03
(1)
Menu programming screen
[(OPRT)][MENU]
Software operator’s panel screen
[OPR]
Tool life management setting screen
[TOOLLF]
Y axis tool offset screen
[OFST.2]
[(OPRT)]
[WEAR] [GEOM]
(Number) [CLEAR]
(Numeral)
[(OPRT)]
[SELECT](Number)
[NO SRH] [CAN] [EXEC] [INPUT]
(Number) (Axis name and numeral) [MEASUR] (Axis name) (Numeral) (Numeral)
[NO SRH]
[INP.C.] [+INPUT] [INPUT]
2/2
Workpiece shift screen
[WK.SHFT]
[(OPRT)
[CLEAR] [ALL]
[WEAR] [GEOM]
[READ] [CAN]
[EXEC
]
[PUNCH] [CAN]
[EXEC
]
(Numeral)
]
(Numeral)
[+INPUT] [INPUT]
14
B–62445E/03
1. DISPLA Y AND OPERATION OF CRT/MDI
OFFSET/SETTING SCREEN (M series)
OFFSET
SETTING
Tool offset screen
[OFFSET]
Setting screen
[SETING]
Work coordinate system setting screen
[(OPRT)]
[(OPRT)]
(Number) (Axis name) (Numeral) (Numeral)
(Number) [ON:1] [OFF:0] (Numeral) (Numeral)
Soft key transition triggered by the function key
[NO SRH]
[INP.C.] [+INPUT] [INPUT]
[NO SRH]
[+INPUT] [INPUT]
OFFSET
SETTING
[WORK]
Macro variables display screen
[MACRO]
Menu programming screen
[MENU]
Software operator’s panel screen
[OPR]
[(OPRT)]
[(OPRT)]
[(OPRT)]
(Number) (Numeral) (Numeral)
(Number) (Axis name) [INP.C.] (Numeral)
[PUNCH]
[NO SRH] [+INPUT] [INPUT]
[NO SRH]
[INPUT]
[SELECT](Number)
Tool life management setting screen
[TOOLLF]
[(OPRT)]
(Number)
[CLEAR]
(Numeral)
[NO SRH] [CAN] [EXEC] [INPUT]
15
1. DISPLA Y AND OPERATION OF CRT/MDI
B–62445E/03
SYSTEM SCREEN
SYSTEM
Parameter screen
[PARAM]
Diagnosis screen
Soft key transition triggered by the function key
[(OPRT)]
(Number)
[ON:1]
[OFF:0] (Numeral) (Numeral)
[READ] [CAN]
[PUNCH] [CAN]
[NO SRH]
[+INPUT] [INPUT]
[EXEC]
[EXEC]
To enter a file number: Press , enter a file number, then press on the PRGRM screen
SYSTEM
1/3
N
INPUT
[DGNOS]
PMC screen
[PMC]
(1) (Continued on the next page)
(2)
[(OPRT)]
[PMCLAD]
[SEARCH]
[ADRESS]/[SYMBOL]
[WINDOW]
(3)
[NO SRH](Number)
[TOP] [BOTTOM] [SRCH] [W–SRCH] [N–SRCH]
[F–SRCH]
[TRGON][TRIGER] [TRGOFF] [START]
[DPARA]/[NDPARA] [TRGSRC] [INIT] [DIVIDE] [CANCEL] [DELETE] [SELECT] [WIDTH]
[SEARCH][DUMP]
[BYTE] [WORD] [D.WORD]
16
B–62445E/03
1. DISPLA Y AND OPERATION OF CRT/MDI
(1)
(2) (3)
[PMCDGN]
With PMC–RC only
[PMCPRM]
[STOP]/[RUN] [I/O] [EXEC]
[DUMP]
[DRARA]/[NDPARA] [TITLE] [STATUS] [ALARM] [TRACE] [T.DISP]/[TRCPRM]
[M.SRCH] [SEARCH]
[ANALYS]
[TIMER] [COUNTR] [KEEPRL] [DATA]
[SETTING] [YES]/[MANUAL]/[ROM]
[CANCEL]
(No.)
[SEARCH]
[BYTE] [WORD] [D.WORD]
[SEARCH]
[EXEC]
[INPUT] [SCOPE] [DELETE] [INIT]
[ADRESS]/[SYMBOL]
[G.DATA] [G.CONT] [NO.SRH] [INIT]
[NO]/[AUTO]/[RAM]
[SGNPRM] [STAR T]/[STOP] [T–SRCH] [ADRESS]/[SYMBOL] [EXCHG] [SELECT]
[C.DATA] [G–SRCH] [SEARCH]
2/3
[TO] [EXEC]
[CANCEL]
System configuration screen
[SYSTEM]
(4) (Continued on the next page)
[SPEED] [INPUT]
[INIT]
[MDI]/[ROM]
17
1. DISPLA Y AND OPERATION OF CRT/MDI
B–62445E/03
(4)
Pitch error compensation screen
[PITCH]
Servo parameter screen
[SV.PRM]
[(OPRT)]
[SV .SET]
[SV .TUN]
[SV .TRC] [(OPRT)]
(No.)
[ON:1]
[OFF:0] (Numeral) (Numeral)
[READ] [CAN]
[PUNCH] [CAN]
[(OPRT)]
[NO SRH]
[+INPUT] [INPUT]
[EXEC]
[EXEC]
To enter a file number: Press , enter a file number, then press on the PRGRM screen
[ON:1] [OFF:0] (Numeral)
[TRACE] [TRNSF]
[INPUT]
INPUT
N
3/3
Spindle parameter screen
[SP.PRM]
Waveform diagnosis screen
[W.DGNS]
[SP.SET] [SP.TUN] [SP.MON]
[W.PRM] [W.GRPH]
[(OPRT)]
[STSRT] [TIME] [TIME] [H–DOBL] [H–HALF]
[STSRT] [CH–1] [CH–1] [V–DOBL] [V–HALF]
[ON:1] [OFF:0] [INPUT]
[STSRT] [CH–2] [CH–2] [V–DOBL] [V–HALF]
18
B–62445E/03
1. DISPLA Y AND OPERATION OF CRT/MDI
MESSAGE SCREEN
MESSAGE
Alarm display screen
[ALARM]
Message display screen
[MSG]
Alarm history screen
[HISTRY]
HELP SCREEN
Soft key transition triggered by the function key
[(OPRT)]
[CLEAR]
Soft key transition triggered by the function key
MESSAGE
HELP
HELP
Alarm detail screen
[1 ALAM]
Operation method screen
[2 OPR]
Parameter table screen
[3 PARA]
[(OPRT)]
[(OPRT)] [SELECT]
[SELECT]
19
Loading...
+ 496 hidden pages