Bosch GDR 12-LI User Manual

Robert Bosch Power Tools GmbH

70538 Stuttgart

GERMANY

www.bosch-pt.com

1 609 92A 4AC (2018.10) AS / 43

1 609 92A 4AC

GDR 12-LI Professional

en Original instructions zh zh ko

th

id Petunjuk-Petunjuk untuk Penggun-

aan Orisinal

vi Bản gốc hướng dẫn sửdụng

2 |

English ...................................................	page	5
.......................................................	12
..................................................	16
...............................................	20
......................................................	24
Bahasa Indonesia.....................................	Halaman	29
Tiếng Việt ...............................................	Trang	34

1 609 92A 4AC | (05.10.2018)					Bosch Power Tools

| 3

(4)

(1)

(5)

(6)

(10)

GDR 12-LI

Bosch Power Tools					1 609 92A 4AC | (05.10.2018)

4 |
A	B
	(1) (2)
	(13)
	(11)
	(12)
(6)	(5)
C
(7)
	(7)
1 609 92A 4AC | (05.10.2018)	Bosch Power Tools

English

Safety instructions

General Power Tool Safety Warnings

WARNING Read all safety warnings, instructions, illustrations and specifica-

tions provided with this power tool. Failure to follow all in-

structions listed below may result in electric shock, fire and/

or serious injury.

Save all warnings and instructions for future reference.

The term "power tool" in the warnings refers to your mainsoperated (corded) power tool or battery-operated (cordless) power tool.

Work area safety

uKeep work area clean and well lit. Cluttered or dark areas invite accidents.

uDo not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.

uKeep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

Electrical safety

uPower tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

uAvoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.

uDo not expose power tools to rain or wet conditions.

Water entering a power tool will increase the risk of electric shock.

uDo not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts.

Damaged or entangled cords increase the risk of electric shock.

uWhen operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.

uIf operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.

Personal safety

uStay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inatten-

English | 5

tion while operating power tools may result in serious personal injury.

uUse personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.

uPrevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool.

Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.

uRemove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

uDo not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

uDress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.

uIf devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.

uDo not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.

Power tool use and care

uDo not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

uDo not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

uDisconnect the plug from the power source and/or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

uStore idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

uMaintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

Bosch Power Tools					1 609 92A 4AC | (05.10.2018)

6 | English

uKeep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

uUse the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

uKeep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.

Battery tool use and care

uRecharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

uUse power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.

uWhen battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another.

Shorting the battery terminals together may cause burns or a fire.

uUnder abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.

uDo not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.

uDo not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130°C may cause explosion.

uFollow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire.

Service

uHave your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

uNever service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorized service providers.

Safety Warnings for Impact Wrenches

uHold the power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a "live"

wire may make exposed metal parts of the power tool

"live" and could give the operator an electric shock.

uUse suitable detectors to determine if there are hidden supply lines or contact the local utility company for assistance. Contact with electric cables can cause fire and electric shock. Damaging gas lines can lead to explosion. Breaking water pipes causes property damage.

uHold the power tool securely. When tightening and loosening screws be prepared for temporarily high torque reactions.

uSecure the workpiece. A workpiece clamped with clamping devices or in a vice is held more secure than by hand.

uAlways wait until the power tool has come to a complete stop before placing it down. The application tool can jam and cause you to lose control of the power tool.

uIn case of damage and improper use of the battery, vapours may be emitted. Ensure the area is well-ventilated and seek medical attention should you experience any adverse effects. The vapours may irritate the respiratory system.

uDo not open the battery. There is a risk of short-circuit- ing.

uThe battery can be damaged by pointed objects such as nails or screwdrivers or by force applied externally.

An internal short circuit may occur, causing the battery to burn, smoke, explode or overheat.

uOnly use the battery with products from the manufacturer. This is the only way in which you can protect the battery against dangerous overload.

Protect the battery against heat, e.g.

against continuous intense sunlight, fire,

water, and moisture. There is a risk of explo-

sion.

Product Description and

Specifications

Read all the safety and general instructions.

Failure to observe the safety and general instructions may result in electric shock, fire and/or serious injury.

Please observe the illustrations at the beginning of this operating manual.

Intended Use

The machine is intended for driving in and loosening screws and bolts as well as for tightening and loosening nuts within the respective range of dimension.

Product Features

The numbering of the product features refers to the diagram of the power tool on the graphics page.

(1)Tool holder

(2)Locking sleeve

1 609 92A 4AC | (05.10.2018)					Bosch Power Tools

(3)"PowerLight"

(4)Carrying strap lug

(5)Battery release button

(6)Battery

(7)Rotational direction switch

(8)On/off switch

(9)Battery charge indicator

(10)Handle (insulated gripping surface)

(11)Universal bit holder

(12)Screwdriver bit

(13)Screwdriver bit with ball catch

Technical Data

Impact wrench			GDR 12-LI
Article number			3 601 JA6 9..
Rated voltage		V=	12
No-load speed		rpm	0–2 600
Impact rate		rpm	0–3 100
Maximum torque, hard		Nm	105
screwdriving application ac-
cording to ISO 5393
Machine screw diameter			M4–M12
Max. screw diameter		mm	8
Tool holder			¼" internal
			hexagon
Weight according to		kg	1.0–1.2
EPTA-Procedure 01:2014
Permitted ambient temperature
– during charging		°C	0 to +45
– during operation A) and		°C	-20 to +50
during storage
Recommended batteries			GBA 12V..
			GBA 10.8V..
Recommended chargers			GAL 12.. CV
			AL 11.. CV
			GAL 12V-..
			GAX 18V-30

A) Limited performance at temperatures <0 °C

Assembly

Battery charging (see figure A)

uUse only the chargers listed on the accessories page.

Only these chargers are matched to the lithium-ion battery of your power tool.

Note: The battery is supplied partially charged. To ensure full battery capacity, fully charge the battery in the charger before using your power tool for the first time.

English | 7

The lithium-ion battery can be charged at any time without reducing its service life. Interrupting the charging process does not damage the battery.

The lithium-ion battery is protected against deep discharge by the "Electronic Cell Protection (ECP)". When the battery is discharged, the power tool is switched off by means of a protective circuit: The application tool no longer rotates.

uDo not continue to press the On/Off switch after the power tool has automatically switched off. The battery can be damaged.

To remove the battery (6), press the release button (5) and pull the battery downwards out of the power tool. Do not

use force to do this.

The battery features NTC temperature monitoring, which only permits charging in a temperature range between 0 °C and 45 °C. This achieves a long battery life.

Follow the instructions on correct disposal.

Changing the Tool

uRemove the battery from the power tool before carrying out work on the power tool (e.g. maintenance, changing tool, etc.). The battery should also be removed for transport and storage. There is risk of injury from unintentionally pressing the on/off switch.

Inserting the application tool

Pull the locking sleeve (2) forward, guide the application tool

(1) into the tool holder up to the stop and release the locking sleeve (2) to lock the application tool.

Only use screwdriver bits with ball catch (13) (DIN 3126E6.3). Other screwdriver bits (12) can be inserted using a universal bit holder with ball catch (11).

Removing

Pull the locking sleeve (2) forward and remove the application tool.

Operation

Method of Operation

The tool holder (1) (with the application tool) is driven by an electric motor via a gear and impact mechanism.

The working procedure is divided into two phases: Screwing in and tightening (impact mechanism in action).

The impact mechanism is activated as soon as the screwed connection becomes tightened, exerting a load on the motor. The impact mechanism then converts the power of the motor to steady rotary impacts. When loosening screws or nuts, the process is reversed.

Start-up

Inserting the Battery

Note: The use of batteries unsuitable for your power tool can lead to malfunctions or damage to the power tool.

Set the rotational direction switch (7) to the middle position to avoid unintentionally switching it on. Insert the charged

Bosch Power Tools					1 609 92A 4AC | (05.10.2018)

8 | English

battery (6) into the handle until you feel it engage and it is flush with the handle.

Set the Rotational Direction (see figure C)

The rotational direction switch (7) is used to change the rotational direction of the power tool. However, this is not possible while the on/off switch (8) is being pressed.

Right rotation: To drive in screws and tighten nuts, press the rotational direction switch (7) through to the left stop.

Left rotation: To loosen and unscrew screws and nuts, press the rotational direction switch (7) through to the right stop.

Switching On and Off

To start the power tool, press and hold the on/off switch

(8).

The lamp (3) lights up when the on/off switch (8) is lightly or fully pressed, meaning that the work area is illuminated in poor lighting conditions.

To switch off the power tool, release the on/off switch (8).

Adjusting the Speed

You can adjust the speed of the power tool when it is on by pressing in the on/off switch (8) to varying extents. Applying light pressure to the on/off switch (8) results in a low rotational speed. Applying increasing pressure to the switch increases the speed.

Battery Charge Indicator

When the on/off switch (8) is pressed in halfway or completely, the battery charge indicator (9) indicates the battery's state of charge for several seconds. The indicator consists of three green LEDs.

LED	Capacity
Continuous lighting 3 x green	≥ 66%
Continuous lighting 2 x green	33–66%
Continuous lighting 1 x green	≤ 33%
Flashing light 1 x green	Reserve

Temperature-dependent overload protection

When used as intended, the power tool cannot be overloaded. In the event of heaving loading or the temperature rising/falling outside the permitted battery temperature range, the speed will be reduced. The power tool will not run at full speed again until the permitted battery temperature has been reached.

Guide values for maximum screw tightening torques

Protection against deep discharge

The lithium-ion battery is protected against deep discharge by the Electronic Cell Protection (ECP). When the battery is discharged, the power tool is switched off by means of a protective circuit: The application tool no longer rotates.

Practical advice

uOnly apply the power tool to the screw/nut when the tool is switched off. Rotating tool inserts can slip off.

The torque depends on the impact duration. The maximum achieved torque results from the sum of all individual torques achieved through impact. Maximum torque is achieved after an impact duration of 6–10 seconds. After this duration, the tightening torque is increased only minimally.

The impact duration is to be determined for each required tightening torque. The actually achieved tightening torque is always to be checked with a torque wrench.

Screw applications with hard, spring-loaded or soft seats

When the achieved torques in an impact series are measured during a test and transferred into a diagram, the result is the curve of a torque characteristic. The height of the curve corresponds with the maximum reachable torque, and the steepness indicates the duration in which this is achieved.

A torque gradient depends on the following factors:

–Strength properties of the screws/nuts

–Type of backing (washer, disc spring, seal)

–Strength properties of the material being screwed/bolted together

–Lubrication conditions at the screw/bolt connection

The following application cases result accordingly:

–A hard seat is a metal-to-metal screw application which uses washers. After a relatively short impact duration, the maximum torque is reached (steep characteristic curve). Unnecessary long impact duration only causes damage to the machine.

–A spring-loaded seat is also a metal-to-metal screw application but uses spring washers, disc springs, studs or screws/nuts with conical seats. It is also called a springloaded seat when extensions are used.

–A soft seat is a screw application of e.g. metal on wood or a screw application that uses lead washers or fibre washers as backing.

For a spring-loaded seat as well as for a soft seat, the maximum tightening torque is lower than for a hard seat. Also, a clearly longer impact duration is required.

Figures given in Nm; calculated from the tensional cross-section; utilization of the yield point: 90% (with friction coefficient µtotal = 0.12). As a control measure, always check the tightening torque with a torque wrench.

	Property classes	Standard screws/bolts								High-strength bolts
	according to	3.6	4.6	5.6	4.8	6.6	5.8	6.8	6.9	8.8	10.9	12.9
	DIN 267
	M6	2.71	3.61	4.52	4.8	5.42	6.02	7.22	8.13	9.7	13.6	16.2
	M8	6.57	8.7	11	11.6	13.1	14.6	17.5	19.7	23	33	39
	M10	13	17.5	22	23	26	29	35	39	47	65	78

1 609 92A 4AC | (05.10.2018)					Bosch Power Tools

												English | 9
	Property classes	Standard screws/bolts								High-strength bolts
	according to
		3.6	4.6	5.6	4.8	6.6	5.8	6.8	6.9	8.8	10.9	12.9
	DIN 267
	M12	22.6	30	37.6	40	45	50	60	67	80	113		135

Tips

Before screwing larger, longer screws into hard materials, it is advisable to pre-drill a pilot hole with the core diameter of the thread to approx. 2/3 of the screw length.

Maintenance and Servicing

Maintenance and cleaning

uTo ensure safe and efficient operation, always keep the power tool and the ventilation slots clean.

If the power tool should fail despite the care taken in manufacturing and testing procedures, the repair should be carried out by an after-sales service centre for Bosch power tools.

In all correspondence and spare parts orders, please always include the 10 digit article number given on the type plate of the power tool.

After-sales Service and Advice on Using

Products

Our after-sales service can answer questions concerning product maintenance and repair, as well as spare parts. You can find exploded drawings and information on spare parts at: www.bosch-pt.com

The Bosch product use advice team will be happy to help you with any questions about our products and their accessories.

www.powertool-portal.de, the internet portal for tradespeople and DIY enthusiasts.

In all correspondence and spare parts orders, please always include the 10 digit article number given on the type plate of the product.

Cambodia

Robert Bosch (Cambodia) Co., Ltd

Unit 8BC, GT Tower, 08th Floor, Street 169,

Czechoslovakia Blvd, Sangkat Veal Vong

Khan 7 Makara, Phnom Penh

VAT TIN: 100 169 511

Tel.: [phone]

Tel.: [phone]

www.bosch.com.kh

People’s Republic of China

China Mainland

Bosch Power Tool (China) Co. Ltd.

Bosch Service Center

567, Bin Kang Road

Bin Kang District

Hangzhou, Zhejiang Province

China 310052

Tel.: [phone] / 5588

Fax: [phone] x 5566# / 5588#

E-mail: [e-mail]

www.bosch-pt.com.cn

HK and Macau Special Administrative Regions

Robert Bosch Co. Ltd.

21st Floor, 625 King’s Road

North Point, Hong Kong

Customer Service Hotline: [phone]

Fax: [phone]

E-mail: [e-mail]

www.bosch-pt.com.hk

India

Bosch Service Center

69, Habibullah Road, (next to PSBB School), T. Nagar Chennai–600077

Phone: [phone]

Bosch Service Center Rishyamook

85A, Panchkuin Road

New Delhi–110001

Phone: [phone]

Bosch Service Center 79,

Crystal Bldg., Dr. Annie Besant Road, Worli

Mumbai–400018

Phone: [phone]

Indonesia

PT Robert Bosch

Palma Tower 10th Floor

Jalan RA Kartini II-S Kaveling 6

Pondok Pinang, Kebayoran Lama

Jakarta Selatan 12310

Tel.: [phone]

www.bosch-pt.co.id

Malaysia

Robert Bosch Sdn. Bhd.(220975-V) PT/SMY

No. 8A, Jalan 13/6

46200 Petaling Jaya

Selangor

Tel.: [phone]

Toll-Free: 1800 880188

Fax: [phone]

E-mail: [e-mail]

www.bosch-pt.com.my

Pakistan

Robert Bosch Middle East FZE – Pakistan Liaison Office 2nd Floor Plaza # 10, CCA Block, DHA Phase 5 Lahore, 54810

Phone: [phone]

E-mail: [e-mail]

Philippines

Robert Bosch, Inc.

28th Floor Fort Legend Towers,

Bosch Power Tools					1 609 92A 4AC | (05.10.2018)

10 | English

3rd Avenue corner 31st Street, Fort Bonifacio, Global City, 1634 Taguig City

Tel.: [phone]

Fax: [phone]

www.bosch-pt.com.ph

Singapore

Powerwell Service Centre Ptd Ltd

Bosch Authorised Service Centre (Power Tools) 4012 Ang Mo Kio Ave 10, #01-02 TECHplace Singapore 569628

Tel.: [phone]

Fax: [phone]

E-mail: [e-mail]

www.powerwellsc.com

www.bosch-pt.com.sg

Thailand

Robert Bosch Ltd.

Liberty Square Building

No. 287, 11 Floor

Silom Road, Bangrak

Bangkok 10500

Tel.: [phone]

Fax: [phone]

Robert Bosch Ltd., P. O. Box 2054

Bangkok 10501

www.bosch.co.th

Bosch Service – Training Centre

La Salle Tower Ground Floor Unit No.2 10/11 La Salle Moo 16

Srinakharin Road

Bangkaew, Bang Plee

Samutprakarn 10540

Tel.: [phone]

Fax: [phone]

Vietnam

Branch of Bosch Vietnam Co., Ltd in HCMC 14th floor, Deutsches Haus, 33 Le Duan Ben Nghe Ward, District 1, Ho Chi Minh City Tel.: [phone]

Fax: [phone]

Hotline: [phone]

E-mail: [e-mail] www.bosch-pt.com.vn

Armenia, Azerbaijan, Georgia, Kyrgyzstan, Mongolia,

Tajikistan, Turkmenistan, Uzbekistan

TOO "Robert Bosch" Power Tools, After Sales Service Rayimbek Ave., 169/1

050050, Almaty, Kazakhstan

Service e-mail: [e-mail]

Official website: www.bosch.com, www.bosch-pt.com

Bahrain

Hatem Al Juffali Technical Equipment Establishment. Kingdom of Bahrain, Setra Highway, Al Aker Area Phone: [phone]

Fax: [phone]

E-mail: [e-mail]

Egypt

Unimar

20 Markaz kadmat

El tagmoa EL Aoul – New Cairo

Phone: [phone]

Phone: [phone]

Fax: [phone]

E-mail: [e-mail]

Iran

Robert Bosch Iran

3rd Floor, No 3, Maadiran Building Aftab St., Khodami St., Vanak Sq. Tehran 1994834571

Phone: [phone]

Iraq

Sahba Technology Group

Al Muthana airport road

Baghdad

Phone: [phone]

Phone Dubai: [phone]

E-mail: [e-mail]

Jordan

Roots Arabia – Jordan

Nasser Bin Jameel street, Building 37 Al Rabiah 11194 Amman

Phone: [phone]

E-mail: [e-mail]

Kuwait

Al Qurain Automotive Trading Company

Shuwaikh Industrial Area, Block 1, Plot 16, Street 3rd P.O. Box 164 – Safat 13002

Phone: [phone]

Fax: [phone]

E-mail: [e-mail]

Lebanon

Tehini Hana & Co. S.A.R.L.

P.O. Box 90-449

Jdeideh

Dora-Beirut

Phone: [phone]

E-mail: [e-mail]

Libya

El Naser for Workshop Tools

Swanee Road, Alfalah Area

Tripoli

Phone: [phone]

Oman

Malatan Trading & Contracting LLC

P.O. Box 131

Ruwi, 112 Sultanate of Oman

Phone: [phone]

E-mail: [e-mail]

Qatar

International Construction Solutions W L L

P. O. Box 51,

Doha Phone: [phone]

1 609 92A 4AC | (05.10.2018)					Bosch Power Tools

Fax: [phone]

E-mail: [e-mail]

Saudi Arabia

Juffali Technical Equipment Co. (JTECO)

Kilo 14, Madinah Road, Al Bawadi District

Jeddah 21431

Phone: [phone] Ext. 1528

Fax: [phone]

E-mail: [e-mail]

Syria

Dallal Establishment for Power Tools

P.O. Box 1030

Aleppo

Phone: [phone]

E-mail: [e-mail]

United Arab Emirates

Central Motors & Equipment LLC, P.O. Box 1984 Al-Wahda Street – Old Sana Building

Sharjah

Phone: [phone]

Fax: [phone]

E-mail: [e-mail]

Yemen

Abualrejal Trading Corporation

Sana’a Zubiery St. Front to new Parliament Building Phone: [phone]

Fax: [phone]

E-mail: [e-mail]

Ethiopia

Forever plc

Kebele 2,754, BP 4806,

Addis Ababa

Phone: [phone]

E-mail: [e-mail]

Ghana

C.WOERMANN LTD.

Nsawam Road/Avenor Junction, P.O. Box 1779 Accra Phone: [phone]

Kenya

Robert Bosch East Africa Ltd

Mpaka Road P.O. Box 856

00606 Nairobi

Nigeria

Robert Bosch Nigeria Ltd.

52–54 Isaac John Street P.O. Box

GRA Ikeja – Lagos

Republic of South Africa

Customer service

Hotline: [phone]

Gauteng – BSC Service Centre

35 Roper Street, New Centre

Johannesburg

Tel.: [phone]

Fax: [phone]

E-mail: [e-mail]

English | 11

KZN – BSC Service Centre

Unit E, Almar Centre

143 Crompton Street

Pinetown

Tel.: [phone]

Fax: [phone]

E-mail: [e-mail]

Western Cape – BSC Service Centre

Democracy Way, Prosperity Park

Milnerton

Tel.: [phone]

Fax: [phone]

E-mail: [e-mail]

Bosch Headquarters

Midrand, Gauteng

Tel.: [phone]

Fax: [phone]

E-mail: [e-mail]

Tanzania

Diesel & Autoelectric Service Ltd.

117 Nyerere Rd., P.O. Box 70839

Vingunguti 12109, Dar Es Salaam

Phone: [phone]

Australia, New Zealand and Pacific Islands

Robert Bosch Australia Pty. Ltd.

Power Tools

Locked Bag 66

Clayton South VIC 3169

Customer Contact Center

Inside Australia:

Phone: [phone]

Fax: [phone]

Inside New Zealand:

Phone: [phone]

Fax: [phone]

Outside AU and NZ:

Phone: [phone]

www.bosch-pt.com.au

www.bosch-pt.co.nz

Transport

The contained lithium-ion batteries are subject to the Dangerous Goods Legislation requirements. The batteries are suitable for road-transport by the user without further restrictions.

When shipping by third parties (e.g.: by air transport or forwarding agency), special requirements on packaging and labelling must be observed. For preparation of the item being shipped, consulting an expert for hazardous material is required.

Dispatch battery packs only when the housing is undamaged. Tape or mask off open contacts and pack up the battery in such a manner that it cannot move around in the packaging. Please also observe the possibility of more detailed national regulations.

Bosch Power Tools					1 609 92A 4AC | (05.10.2018)

12 |

Disposal

The machine, rechargeable batteries, accessories and packaging should be sorted for environmental-friendly recycling.

Do not dispose of power tools and batteries/ rechargeable batteries into household waste!

Battery packs/batteries:

Li-ion:

Please observe the notes in the section on transport (see "Transport", page 11).

/

警告中的术语“ ”

u 燃粉尘或气体。

u 集中会使你失去对工具的控制。

u 换插头。未经改装的插头和相配的插座将降低电 击风险。

u 箱。

u 入电动工具将增加电击风险。

运动部件。

u 延长线。

u 使用带有剩余电流装置RCD RCD

u 工具时瞬间的疏忽会导致严重人身伤害。

u 鞋、安全帽、听力防护等装置能减少人身伤害。

u/

u 手。遗留在电动工具旋转零件上的扳手或钥匙会 导致人身伤害。

u 发可能会卷入运动部件。

u 确保其连接完好且使用得当。使用集尘装置可降 低尘屑引起的危险。

u 在瞬间导致严重的伤害。

u 动工具。选用合适的按照额定值设计的电动工具 会使你工作更有效、更安全。

u 的且必须进行修理。

u/

u 用者手中是危险的。

u 电动工具。许多事故是由维护不良的电动工具引 发的。

u 动工具用于那些与其用途不符的操作可能会导致 危险情况。

u 的安全和对工具的控制。

1 609 92A 4AC | (05.10.2018)					Bosch Power Tools

u 险。

u 具。

u 会引起

u 液体会发

u 有着火、爆炸或受伤的风险。

u 火焰或超过130°C

u 超出说明中规定的温度范围。错误充电或温度超 出规定的范围可能会损坏电池并提高着火的风 险。

u 授权的服务商进行电池组的维护保养。

u 电动工具的绝缘握持面。一旦紧固件接触“”“ ”

u 並让操作者触电。损坏了瓦斯管会引起爆炸。如 果水管被刺穿了会导致财物损失。

u 会比用手持握工件更牢固。

u 电动工具。

u 池散发的蒸汽会刺激呼吸道。

u 发出烟雾、爆炸或过热。

u 能确保充电电池不会过载。

| 13

的危险。

下警告和说明可能导致电击、着火和/

和放松规定尺寸内的螺母。

(3)“PowerLight”

		GDR 12-LI
		3 601 JA6 9..
	=	12
	/	0–2 600
	/	0–3 100
ISO 5393		105
		M4–M12
		8
		¼"
		1.0–1.2
EPTA-Procedure 01:2014
–		0 +45
– A)		-20 +50
		GBA 12V..
		GBA 10,8V..

Bosch Power Tools					1 609 92A 4AC | (05.10.2018)