Instructions for use
Cooker hood
CW4938G / WS90ENTEE CW41238G / WS12ENTEE
EN Manual |
EN 3 - EN 23 |
Pictograms used:
Important information
Tip
EN 4
CONTENTS
Your cooker hood
Introduction |
4 |
Use
Description |
5 |
Operation |
6 |
Cleaning filters |
8 |
Maintenance
Cleaning |
9 |
Installation
General |
12 |
Connection |
13 |
Build-in dimensions |
14 |
Assembly |
15 |
Technical specifications
|
|
22 |
|
Appendix |
|||
|
|||
|
Disposal |
23 |
|
|
EN 3
YOUR COOKER HOOD
Introduction
On reading these user manuals you will soon become familiar with the features of this appliance. Please read the appliance’s safety and maintenance instructions.
Please retain the operating and installation instructions as these may be useful for future reference.
Please read the separate safety instructions prior to use.
EN 4
USE
Description
1 |
2 |
3 |
4 |
5 |
6 |
7 |
8 |
9 |
1.Switching on/off and dimming the lighting
2.Reducing air extraction capacity and switching off
3.Cleaning carbon filter indicator
4.Cleaning grease filter indicator
5.Display status
6.Timer function indicator
7.Clean Air function indicator
8.Switching on and increasing air extraction capacity
9.Switching on timer function
Note!
• Prior to activating or deactivating a function, the motor and lighting should be switched off.
•If you have a cooker hood with a carbon filter, you should activate the carbon filter indicator as described in the ‘Cleaning filters’ paragraph.
EN 5
USE
Operation
Switching extraction on and off
•Press the ‘+’ button (8).
The cooker hood will switch on at the lowest setting.
•Press the ‘+’ button (8) again to set a higher extraction setting.
Press and hold the ‘+’ button (8) for 2 seconds to select the highest setting (boost) (see switching on intensive setting).
The extraction setting can be set between speeds 1 to 5 or 9 (depending on the model).
•Press the ‘-’ button (2) to select a lower setting.
The extraction setting is indicated in the display (5).
•If the extraction setting is set at 1, you can switch off the cooker hood by quickly pressing and releasing the ‘-’ button (2).
•To switch off the cooker hood from whatever setting press and hold the ‘-’ button (2) for at least 2 seconds.
Alter the number of speed-settings (models with 9 speed-settings)
You can choose between 9 speed-settings (standard) or 5 speedsettings.
•Press and hold the ‘-’ button (2) and ‘+’ button (8) for at least 5 seconds.
This selects the 5 speed-setting option. Press and hold the ‘-’ button (2) and ‘+’ button (8) again for at least 5 seconds to select the 9 speed-setting option.
Switching the lighting on and off
•Quickly press and release the lighting button (1).
The light switches on at maximum strength.
•Press and hold the lighting button (1) to set the lighting strength.
•To turn off the light, quickly press and release the lighting button (1) while the light is on.
The lighting changes from maximum to minimum strength and vice versa.
EN 6
USE
Switch on intensive setting:
•Press and hold the ‘+’ button (8) for approximately 2 seconds.
The intensive setting (setting ‘P’) is switched on for ten minutes (depending on the model). The display will flash (5) during this period. The original extraction setting will be reactivated after this period.
•Quickly press and release the ‘+’ (8) button to switch off the intensive setting.
Switching on the timer
•Press the timer button (9).
The timer indicator (6) will light up.
The cooker hood will switch off automatically after 10 minutes.
•Switch off the timer function by pressing the ‘-’ button ‘2’.
If the lighting is lit its strength will be reduced automatically by 30-40% once the timer has finished.
Note!
If the intensive setting has been selected you cannot activate the timer function.
Clean Air function
The Clean Air function allows you to freshen the air in your kitchen for a maximum of 12 hours.
•Switch off the cooker hood.
•Press and hold the timer button (9) for approximately 4 seconds.
The cooker hood will switch on automatically for 10 minutes every hour at the lowest speed setting. During extraction the Clean Air indicator will flash (7).
When the hood switches off after 10 minutes, the Clean Air indicator (7) will be lit continuously until the hood switches on again after 50 minutes.
•Switch off the Clean Air function in the meantime by pressing a random button (except the one for the lighting).
EN 7
USE
Cleaning filters
Saturation grease and carbon filters
The filters should be replaced or cleaned when the grease filter indicator (4) or the carbon filter indicator (3) are lit.
Grease filter
The grease filter indicator (4) will flash after 30 operating hours.
• The grease filters should then be cleaned.
• Reset the memory by pressing and holding the ‘-’ button (2) until the grease filter indicator (4) stops flashing.
Carbon filter
The carbon filter indicator (3) will flash after 120 operating hours.
• The carbon filter should then be cleaned or replaced.
• Reset the memory by simultaneously pressing and holding the ‘-’ (2) and ‘+’ (8) buttons until the carbon filter indicator (3) stops flashing.
Switching on carbon filter indicator
• Simultaneously press and hold the ‘+’ (8) button and the lighting button (1) until the carbon filter indicator (3) flashes twice.
The carbon filter indicator is activated.
Switching off carbon filter indicator
•Simultaneously press and hold the ‘+’ (8) button and the lighting button (1) until the carbon filter indicator (3) flashes once.
The carbon filter indicator is switched on:
• The carbon filter indicator (3) lights up for 3 seconds.
The carbon filter indicator is switched off:
• The carbon filter indicator (3) flashes for 3 seconds.
EN 8