ANPEC APL1117R-50VC-TU, APL1117R-50VC-TR, APL1117R-50UC-TU, APL1117R-50UC-TR, APL1117R-33VC-TU Datasheet

APL1117D/R

1A, Low Dropout Fast Response Positive Regulator Fixed 3.3V and 5.0V

Features

••

•

Guaranteed Output Voltage Accuracy within 2%

••

•

Fast Transient Response

••

•

Guaranteed Dropout Voltage at Multiple Cur-

••

rents

••

•

Load Regulation : 0.1% Typ.

••

•

Line Regulation : 0.03% Typ.

••

• Low Dropout Voltage : 1.2V Typ. at I

••

• Current Limit : 1A Typ. at T

••

• On-Chip Thermal Limiting : 150 °C Typ.

••

• Standard 3-pin SOT-223 and TO-252 Power

••

Packages

=125 °C

J

OUT

=0.8A

Applications

••

• Active SCSI Terminators

••

General Description

The APL1117D/R is a low dropout three-terminal fixed

3.3V and 5.0V regulators with 1A output current capability. In order to obtain lower dropout voltage and faster transient response, which is critical for low voltage applications , the APL1117D/R has been optimized. The dropout voltage is guaranteed at a maximum of 1.3V at 0.8A. Current limit is trimmed to ensure specified output current and controlled shortcircuit current. On-chip thermal limiting provides protection against any combination of overload that would create excessive junction temperatures. The APL1117D/R is available in the industry standard 3pin SOT-223 and TO-252 the low profile surface mount packages which can be used in applications where space is limited.

Pin Description

Front View for SOT-223

••

• Low Voltage Logic Supplies

••

• Battery-Powered Circuitry

••

• Post Regulator for Switching Power Supply

••

APL1117D GND VOUT VIN

APL1117R VIN GND VOUT

APL1117D GND VOUT VIN

APL1117R VIN GND VOUT

ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise customers to obtain the latest version of relevant information to verify before placing orders.

Copyright  ANPEC Electronics Corp. Rev. A.3 - Jun., 2003

123

Front View for TO-252

123

www.anpec.com.tw1

APL1117D/R

Ordering and Marking Information

APL1117D/R-

APL1117D/R-33U :

APL1117D/R-50U :

APL1117D/R XXXXX

33

50

Handling Code

Temp. Range

Package Code

Voltage Code

XXXXX

- Date Code

Package Code U : TO-252 V : SOT-223 Temp. Range

C : 0 to 70 C

Handling Code

TU : Tube TR : Tape & Reel

Voltage Code

33 : 3.3V 50 : 5.0V

APL1117D/R-33U :

APL1117D/R-50U :

°

APL1117D/R XXXXX33

APL1117D/R XXXXX50

XXXXX - Date Code

Absolute Maximum Ratings

Symbol Parameter Rating Unit

V

I

T

J

T

STG

T

L

Input Voltage 13.2 V Operating Junction Temperature Range

Control Section Power Transistor

0 to 125 0 to 150

Storage Temperature Range -65 to +150

Lead Temperature (Soldering, 10 second) 260

C

°

C

°

C

°

Electrical Characteristics

V

REG

V

I

LIMT

OUT

LINE

LOAD

D

APL1117D/R-33 APL1117D/R-50

Line Regulation

Load Regulation

Dropout Voltage

Current Limit (VIN-V

PSRR Ripple Rejection F

T

L

Copyright  ANPEC Electronics Corp. Rev. A.3 - Jun., 2003

Thermal Regulation TJ=25°C, 30ms Pulse 0.01 %/W

R

Temperature

S

Stability Long -Term

S

Stability

=0~125°C,

T

J

0≤I T I

OUT

T V

I

OUT

(VIN-V

T

0.8A, 4.75V≤V

OUT

≤

=0~125°C,

J

=0.8A, 4.75V≤V

=0~125°C,

J

=4.75A, 0V≤I

IN

0.8A,T

≤

)=5V, TJ=25°C 1 A

OUT

=120Hz, V

RIPPLE

)=3V,TJ=0~125°C

OUT

=125°C, 1000Hrs 0.3 %

J

≤

OUT

=0~125°C

J

RIPPLE=1VP-P

APL1117D/RSymbol Parameter Test Conditions

Min. Typ. Max.

3.235 3.300 3.365

12V 4.900 5.000 5.100

IN

≤

(Note1)

7.75V

IN

≤

(Note 1)

0.8A

60 75 dB

Unit

V

16mV

110mV

1.2 1.3 V

0.5 %

www.anpec.com.tw2

APL1117D/R

Electrical Characteristics

APL1117D/RSymbol Parameter Test Conditions

Unit

Min. Typ. Max.

V

RMS Output Noise

N

Thermal Resistance Junction to Case, at Tab

θ

th

=25°C,10Hz≤F≤10kHz, (% of V

T

J

OUT

)

Junction to ambient

OT

Over Temperature Point

Quiescent Current

Note 1: See thermal regulation specifications for changes in output voltage due to heating effects. Load line regulations are mea-

sured at a constant junction temperature by low duty cycle pulse testing.

Note 2: Dropout voltage is specified over the full output current range of the device. Dropout voltage is defined as the minimum input/

output differential measured at the specified output current. Test points and limits are also shown on the Dropout Voltage curve.

Note 3: Minimum load current is defined as the minimum output current required to maintain regulation.

T

=0~125°C,

J

V

12V

≤

IN

0.003 %

15

C/ W

°

50

150

°

5.5 10 mA

C

Application Schematic

=5~12V V

V

IN

APL1117D/R

OUT

+++

C

IN

10uF

C

OUT1

0.1uF

C

OUT2

10uF

Copyright  ANPEC Electronics Corp. Rev. A.3 - Jun., 2003

www.anpec.com.tw3

APL1117D/R

Typical Characteristics

Input Current vs. Temperature

8

7

6

5

4

Input Current (mA)

3

2

-50 0 50 100 125-25 25 75

Temperature (°C)

Load Transient Response

5



4.5

4

3.5

3

2.5

2

Output Current (A)

1.5

1

0.5

0

-100 0 100 200 300 400 500 600 700 800 900

CIN=10uF Cout=10uF Tantalum VIN=5V

Vout=3.3V

0.02

0.01

0

-0.01

-0.02

-0.03

Current Limit (mA)

Input Voltage (V)

Output Voltage Deviation (V)

Current Limit vs. Temperature

1.3

1.2

1.1

1

Vout=3.3V

Vin-Vout=5V

0.9

0.8

0.7

-50 -30 - 10 10 30 50 70 90 110 130 150

Temperature (°C)

Line Transient Response

130

Vout=3.3V

180

6

5

4

CIN=10uF

3

Cout=10uF Tantalum I

=0.1A

OUT

2

1

0

-20 30 80

0.15

0.1

0.05

0

Output Voltage Deviation (V)

-0.05

Time (µs)

Copyright  ANPEC Electronics Corp.

Time (µs)

www.anpec.com.tw4

Rev. A.3 - Jun., 2003