ANPEC APL5503-34VC-TR, APL5503-34UC-TR, APL5503-34KC-TR, APL5503-34DC-TR, APL5503-34BC-TR Datasheet
...
Low IQ, Low Dropout 500mA Fixed Voltage Regulator
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw1
ANPEC reserves the right to make changes to improve reliability or manufacturability without notice, and advise
customers to obtain the latest version of relevant information to verify before placing orders.
Features
Design with an internal P-channel MOSFET pass
transistor, the APL5501/2/3 maintains a low supply
current, independent of the load current and dropout
voltage. Other features include reverse current
protection, thermal-shutdown protection, current limit
protection to ensure specified output current and controlled short-circuit current. The APL5501/2/3 regulator comes in a miniature SOT-23-5, SOT-89, SOT89-5, SOT-223, SO-8, TO-252 and TO-252-5
packages.
Applications
• Notebook Computer
• PDA or Portable Equipments
• Noise-Sensitive Instrumentation Systems
••
••
• Low Noise : 50µV
RMS
(100Hz to 100kHz)
••
••
• Low Quiescent Current : 50µA (No load)
••
••
• Low Dropout Voltage : 170mV (@500mA)
••
••
• Very low Shutdown Current : < 0.5uA
••
••
• Fixed Output Voltage : 1.3V ~ 3.4V
••
••
• Stable with 4.7uF Output Capacitor
••
••
• Stable with Aluminum , Tantalum or Ceramic
Capacitors .
••
••
• Reverse Current Protection
••
••
• No Protection Diodes Needed
••
••
• Built in Thermal Protection
••
••
• Built in Current Limit Protection
••
••
• Controlled Short Circuit Current : 150mA
••
••
• Fast Transient Response
••
••
• Short Setting Time
••
••
• SOT-23-5, SOT-89, SOT-89-5, SOT-223, SO-8
,TO-252 and TO-252-5 Packages
Pin Configuration
SOT-89 (Top View)
V
IN
GND V
OUT
123
TAB is GND
SOT-89-5 (Top View)
SO-8 (Top View)
1
2
3
45
6
7
8IN
GND
GND
SHDN BYP
GND
GND
OUT
TO-252-5 (Top View)
General Description
The APL5501/2/3 is micropower, low noise, low dropout linear regulator. Operate from 2.7V to 6V input
voltage and deliver up to 500mA. Typical output noise
is just 50µV
RMS
with the addition of an external 0.1µF
bypass capacitor in BP pin and typical dropout voltage is only 170mV at 500mA loading . Designed for
use in battery-powered system, the low 50uA quiescent current makes it an ideal choice.
TO-252 (Top View)
GND
123
V
OUT
V
IN
V
IN
GND
V
OUT
123
54
SHDN
BP
GND
BP
V
OUT
GND
V
IN
12345
TAB is GND
SHDN
SOT-23-5 (Top View)
1
2
34
5V
IN
GND
SHDN BP
V
OUT
APL5501
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw2
Product Name Marking Product Name Marking Product Name Marking
APL5501-13B 517X APL5502-13B 527X APL5503-13B 537X
APL5501-14B 518X APL5502-14B 528X APL5503-14B 538X
APL5501-15B 519X APL5502-15B 529X APL5503-15B 539X
APL5501-16B 51AX APL5502-16B 52AX APL5503-16B 53AX
APL5501-17B 51BX APL5502-17B 52BX APL5503-17B 53BX
APL5501-18B 51CX APL5502-18B 52CX APL5503-18B 53CX
APL5501-19B 51DX APL5502-19B 52DX APL5503-19B 53DX
APL5501-20B 51EX APL5502-20B 52EX APL5503-20B 53EX
APL5501-21B 51FX APL5502-21B 52FX APL5503-21B 53FX
APL5501-22B 51GX APL5502-22B 52GX APL5503-22B 53GX
APL5501-23B 51HX APL5502-23B 52HX APL5503-23B 53HX
APL5501-24B 51IX APL5502-24B 52IX APL5503-24B 53IX
APL5501-25B 51JX APL5502-25B 52JX APL5503-25B 53JX
APL5501-26B 51KX APL5502-26B 52KX APL5503-26B 53KX
APL5501-27B 51LX APL5502-27B 52LX APL5503-27B 53LX
Package C ode
B : SO T-2 3-5 D : S O T-89 D5 : S O T -89 -5
U : TO -2 5 2 U 5 : T O -2 52 -5 V : S O T -22 3
K : S O -8
Tem p. Range
C : 0 to 70 C
Handling Code
TR : Tape & R eel
Voltage Code :
13 : 1.3 V ~ 34 : 3.4V
APL5501/2/3 -
Handling Code
Tem p. Range
Package C ode
Voltage Code
13
APL5 501/2/3
XXXXX
APL5 501/2/3 - 13 U :
XXX XX - Date Code , 13 - 1.3V
XXX XX - Date Code , 13 - 1.3V
APL5 501/2/3
XXXXX13
APL5501/2/3 - 13 D/V/K :
°
Ordering and Marking Information
Pin Configuration (Cont.)
SOT-223 (Top View)
V
OUT
GNDV
IN
123
TAB is GND
APL5501 APL5502
SOT-89 (Top View)
GND
V
IN
V
OUT
123
TAB is V
IN
V
IN
GNDV
OUT
123
TAB is GND
SOT-223 (Top View)
APL5503
V
OUT
V
IN
GND
123
TAB is V
IN
SOT-223 (Top View)
APL5502
Marking Information
SOT-23-5 package
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw3
Product Name Marking Product Name Marking Product Name Marking
APL5501-28B 51MX APL5502-28B 52MX APL5503-28B 53MX
APL5501-29B 51NX APL5502-29B 52NX APL5503-29B 53NX
APL5501-30B 51OX APL5502-30B 52OX APL5503-30B 53OX
APL5501-31B 51PX APL5502-31B 52PX APL5503-31B 53PX
APL5501-32B 51QX APL5502-32B 52QX APL5503-32B 53QX
APL5501-33B 51RX APL5502-33B 52RX APL5503-33B 53RX
APL5501-34B 51SX APL5502-34B 52SX APL5503-34B 53SX
Pin Description
PIN
No. Name
I/O Description
1VINI Supply voltage input.
2 SHDN
(Note1)
I Shutdown control pin, low = off , high = normal .
3GND
Ground pins of the circuitry, and all ground pins must be soldered to
PCB with proper power dissipation.
4BP
(Note1)
O Bypass signal pin in fixed output type device
5V
OUT
O Output pin of the regulator.
Marking Information (Cont.)
SOT-23-5 package
Note1 : These pins do not exist in 3-pin package.
Symbol Parameter Rating Unit
VIN, V
OUT
Input Voltage or Out Voltage 5 V
SHDN
Shutdown Control Pin
5V
R
TH,JA
Thermal Resistance – Junction to Ambient
SOT-89 : 180
SOT-223 : 135
SO-8 : 210
SOT-23-5 : 357
°
C/W
P
D
Power Dissipation Internally Limited W
T
J
Operating Junction Temperature
°
C
Control Section 0 to 125
Power Transistor 0 to 150
T
STG
Storage Temperature Range -65 to +150
°
C
T
L
Lead Temperature (Soldering, 10 second) 260
°
C
Absolute Maximum Ratings
The last character “X” in the marking is for data code.
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw4
Electrical Characteristics
Unless otherwise noted these specifications apply over full temperature, VIN=3.6V, CIN=1µF, COUT=4.7µF,
SHDN=VIN, TJ=0 to 125°C. Typical values refer to TJ=25°C.
APL5501/2/3
Symbol Parameter Test Conditions
Min. Typ. Max.
Unit
V
IN
Input Voltage 2.7 6 V
V
OUT
Output Voltage V
OUT
+1.0V< VCC<6.0V, 0mA< I
OUT
< I
MAX
V
OUT
-2
%
V
OUT
V
OUT
+2
%
V
I
LIMIT
Circuit Current Limit
V
IN
=4.3V
0.7 A
I
SHORT
Short Current V
OUT
=0V 200 mA
I
OUT
Load Current
500 mA
REG
LINE
Line Regulation V
OUT
+0.5V< VCC<6.0V, 0mA< I
OUT
< I
MAX
410mV
REG
LOAD
Load Regulation VIN =V
OUT
+1.0V, 0mA< I
OUT
< I
MAX
1
6
mV
V
DROP
Dropout Voltage
(Note2)
(V
OUT
(Nominal)=3.0V
Version)
I
OUT
=500mA
170 300 mV
PSRR Ripple Rejection
F≤1kHz, 1Vpp at V
IN
= V
OUT
+1.0V
55 65 dB
No load 50 100
I
Q
Quiescent Current
I
OUT
=500mA 370 450
µ
A
Shutdown Supply
Current
(Note3)
Shutdown = low
I
OUT
=0, VCC =6.0V
0.01 1
µ
A
100Hz<f<100kHz, typical load,
C
BP
=0.01µF, C
OUT
= 1µF
50
Noise
(Note3)
100Hz<f<100kHz, typical load,
C
BP
=0.1µF, C
OUT
= 1µF
40
µ
Vrms
CBP=0.01µF,C
OUT
=1µF, no load 7
Shutdown Recovery
Delay
(Note3)
CBP=0.1µF,C
OUT
=1µF, no load 70
ms
OTS
Over Temperature
Shutdown
150
°
C
Over Temperature
Shutdown Hysteresis
Hysteries 10
°
C
TC
Output Voltage
Temperature
Coefficient
50 ppm/°C
C
OUT
Output Capacitor 4.2 4.7 5.2
µ
F
ESR 0.02 0.1 1 Ohm
Shutdown Input
Threshold
(Note3)
V
OUT
+1.0V< VIN <6.0V 0.4 0.7 1.6 V
I
SHDN
Shutdown input Bias
current
(Note3)
V
SHDN
=V
IN
0.01 100 nA
Input Reverse Leakage
current
V
OUT-VIN
=0.1V 0.1 0.5
µ
A
Reverse Protection
Threshold
11 50 mV
Note 2 : Dropout voltage definition : VIN-VOUT when VOUT is 2% below the value of VOUT for VIN = VOUT + 0.5V
Note 3 : For 5-pin devices only.
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw5
Application Circuit
BP
V
OUT
V
IN
GND
SHDN
VOUT
C
IN
1uF
off
on
APL5501/2/3
INP UT
2.7V to 6V
0.1uF
C
BP
C
OUT
4.7uF
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw6
0
0.5
1
1.5
2
2.5
3
3.5 4 4. 5 5 5. 5 6
0
0.5
1
1.5
2
2.5
3
3.5
01234 56
0
50
100
150
200
250
300
350
0123456
0
50
100
150
200
250
300
350
400
0 150 300 450 600 750 900
Typical Characteristics
Input Voltage (V)
Current Limit (mA)
Ground Pin Current vs. Load Current (uA)
Output Current (mA)
Input Voltage (V)
Ground Pin Current vs. Load Current (uA)
Input Voltage (V)
Output Voltage (V)
APL5501/2/3-33
APL5501/2/3-33
APL5501/2/3-33
APL5501/2/3-33
Input Voltage vs. Output VoltageGround Pin Current vs. Input Voltage
Current Limit vs. Input Voltage Ground Pin Current vs. Output Current
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw7
-100
+0
-90
-80
-70
-60
-50
-40
-30
-20
-10
20
200k50 100 200 500
1k 2k 5k 10k 20k
50k 100k
0.4
0.5
0.6
0.7
0.8
0.9
1
3 3.5 4 4.5 5 5.5 6
-12
-10
-8
-6
-4
-2
0
00.511.522.53
0
50
100
150
200
250
0 150 300 450 600 750 900
Typical Characteristics
SHDN Threshold Voltage (V)
Input Voltage (V)
PSRR vs. Frequency
Frequency (HZ)
PSRR (dB)
IOUT =50mA
COUT=10uF
CBP=0.1uF
Output Current (uA)
Output Voltage (V)Output Current (mA)
Dropout Voltage (mV)
VIN=0V
VIN=0V
VIN=4V
VIN=5V
APL5501/2/3-33
APL5501/2/3-33
APL5501/2/3-33
Dropout Voltage vs. Output Current
Output Current vs. Output Voltage
APL5501/2/3-33
SHDN Threshold Voltage vs. Input Voltage
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw8
0
50
100
150
200
250
300
350
400
450
500
0 0.1 0.2 0.3 0.4
-100u
100u
-80u
-
-40u
-20u
0
20u
40u
60u
80u
0
10m
2m
4m 6m 8m
Typical Characteristics
Output Noise
Time (s)
VOUT (50uV/div)
VIN=4.3V
I
OUT =0mA
COUT=10uF
C
BP=0.1uF
Output Noise vs. Bypass Capacitor
Output Noise (uV)
Bypass Capacitor (uF)
Time (1ms/div)
VOUT
vSHDN
Shutdown Exit Delay
Time (20ms/div)
VOUT
vSHDN
CBP=100nF
No Load
Shutdown Exit Delay
APL5501/2/3-33
3.3V
4V
3.3V
4V
0V
0V
0V
0V
CBP=10nF
No Load
APL5501/2/3-33
APL5501/2/3-33
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw9
0.001
0.01
0.1
1
0 150 300 450 600 750 900
VOUT
COUT=1µF
No Load
Typical Characteristics
Entering Shutdown
Time (200ms/div)
VOUT=3.3V
Region of Stable ESR vs. Load Current
Load Current (mA)
COUT ESR (Ω)
unstable
stable
APL5501/2/3-33
APL5501/2/3-33
3.3V
4V
0V
0V
3.25
3.27
3.29
3.31
3.33
3.35
-40 0 40 80 120
Temperature (°C )
Output Voltage (V)
APL5501/2/3-33
Output Voltage vs. Temperature
Time (40µs/div)
VOUT
VIN
Line-Transient Response
Output Voltage (20mV/div)
APL5901/2-33
4V
3V
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw10
COUT=1µF
VIN=VOUT+1V
Typical Characteristics
Time (10µs/div)
APL5501/2/3-33
IOUT=1mA~500mA
Output Voltage (50mV/div)
Load-Transient Response
VOUT
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw11
The minimum input-output voltage difference (dropout)
determines the lowest usable supply voltage. In bat-
tery-powered systems, this will determine the useful
end-of-life battery voltage. Because the APL5501/2/3
use a p-channel MOSFET pass transistor, the drop-
out voltage is a function of drain-to-source on-resis-
tance (R
DS(ON)
) multiplied by the load current.
The APL5501/2/3 load-transient response graphs in
typical characteristics show the transient response.
A step change in the load current from 0mA to 500mA
at 1us will cause a 100mV transient spike. Larger
output capacitor and lower ESR can reduce transient
spike.
Application Information
Capacitor Selection and Regulator
Stability
The APL5501/2/3 use at least a 1uF capacitor on the
input, and this capacitor can be Aluminum, Tantalum
or Ceramic capacitor. The input capacitor with larger
value and lower ESR provides better PSRR and line-
transient response. The output capacitor also can use
Aluminum, Tantalum or Ceramic capacitor, and a mini-
mum value of 1uF and ESR above 0.06Ω is
recommended. The curve of the stable region in typi-
cal characteristics shows the appropriate output ca-
pacitor ESR for different load current stable operation.
A larger output capacitor can reduce noise and im-
prove load-transient response, stability, and PSRR.
Note that some ceramic dielectrics exhibit large ca-
pacitance and ESR variation with temperature. When
using this capacitor, a minimum 10uF or more may
be required to ensure the stability at low temperature
operation. Use a bypass capacitor at BP pin for low
output nvise. Increasing the capacitance will slightly
decrease the output noise, but increase the start-up
time.
Load-Transient Considerations
Input-Output (Dropout)Voltage
Reverse Current Protection
The APL5501/2/3 have an internal reverse protection,
it does not need an external schottky diode to con-
nect the regulator input and output. If the output volt-
age is forced above the input voltage by more than
11mV, the IC will be shutdown and the ground pin
current is below 0.1uA.
Current Limit
The APL5501/2/3 have a current limit protection. The
ouptut voltage will drop close to zero volt, when load
current reaches the limit, and then the load current
will be limited at 150mA after output voltage is below
0.7V. When the load current back to the value where
limiting started, the output voltage and current will re-
turn to normal value. When output is shorted to
ground, the APL5501/2/3 will keep short circuit cur-
rent at 150mA .
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw12
Thermal protection limits total power dissipation in the
device. When the junction temperature exceeds
T
J
=+150J, the thermal sensor generates a logic sig-
nal to turn off the pass transistor and allows IC to
cool. When the IC’s junction temperature is down by
10J, the thermal sensor will turn the pass transistor
on again, resulting in a pulsed output during continu-
ous thermal protection. Thermal protection is designed
to protect the APL5501/2/3 in the event of fault
conditions. For continuous operation, do not exceed
the absolute maximum junction temperature of
T
J
=+150J.
Operating Region and Power Dis-
sipation
The thermal resistance of the case to circuit board,
and the rate of air flow all control the APL5501/2/3’s
maximum power dissipation. The power dissipation
across the device is PD = I
OUT (VIN-VOUT
) and the maxi-
mum power dissipation is:
P
DMAX
= (TJ-TA) / (?JC + ?CA)
where TJ-TA is the temperature difference between the
junction and ambient air, ?JC is the thermal resis-
tance of the package, and ?CA is the thermal resis-
tance through the printed circuit board, copper traces,
and other materials to the ambient air.
The GND pin of the APL5501/3 provide an electrical
connection to ground and channeling heat away. If
power dissipation is large, connect the GND pin to
ground using a large pad or ground plane, can im-
prove the problem of over heat of IC.
Thermal Protection
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw13
Packaging Information
SOT-23-5
e1
E1 E
b
12
3
45
e
D
A2
A
A1 L 2
L
L 1
a
Millimeters Inches
Dim
Min. Max. Min. Max.
A 0.95 1.45
0.037 0.057
A1 0.05 0.15
0.002 0.006
A2 0.90 1.30
0.035 0.051
D2.83.00
0.110 0.118
E2.63.00
0.102 0.118
E1 1.5 1.70
0.059 0.067
L 0.35 0.55
0.014 0.022
L1 0.20 BSC 0.008 BSC
L2 0.5 0.7
0.020 0.028
N5 5
α
0
°
10
°
0
°
10
°
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw14
Packaging Information
Millimeters Inches
Dim
Min. Max. Min. Max.
A 1.35 1.75 0.053 0.069
A1 0.10 0.25 0.004 0.010
D 4.80 5.00 0.189 0.197
E 3.80 4.00 0.150 0.157
H 5.80 6.20 0.228 0.244
L 0.40 1.27 0.016 0.050
e1 0.33 0.51 0.013 0.020
e2 1.27BSC 0.50BSC
φ
18
°
8
°
HE
e1 e2
0.015X45
D
A
A1
0.004max.
1
L
SOP-8 pin ( Reference JEDEC Registration MS-012)
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw15
SOT-223( Reference JEDEC Registration SOT-223)
B1
D
H E
K
e
e1
A
c
L
A1
a
B
b
Millimeters InchesDim
Min. Max. Min. Max.
A 1.50 1.80 0.06 0.07
A1 0.02 0.08
B 0.60 0.80 0.02 0.03
B1 2.90 3.10 0.11 0.12
c 0.28 0.32 0.01 0.01
D 6.30 6.70 0.25 0.26
E 3.30 3.70 0.13 0.15
e 2.3 BSC 0.09 BSC
e1 4.6 BSC 0.18 BSC
H 6.70 7.30 0.26 0.29
L 0.91 1.10 0.04 0.04
K 1.50 2.00 0.06 0.08
α
0
°
10
°
0
°
10
°
β
13
°
13
°
Packaging Information
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw16
Packaging Information
D
D1
e
B1
e1
B
12 3
L
H
E
C
a
a
A
SOT-89 (Reference EIAJ ED-7500A Reg stration SC-62)
Millimeters Inches
Dim
Min. Max. Min. Max.
A 1.40 1.60 0.055 0.063
B 0.40 0.56 0.016 0.022
B1 0.35 0.48 0.014 0.019
C 0.35 0.44 0.014 0.017
D 4.40 4.60 0.173 0.181
D1 1.35 1.83 0.053 0.072
e 1.50 BSC 0.059 BSC
e1 3.00 BSC 0.118 BSC
E 2.29 2.60 0.090 0.102
H 3.75 4.25 0.148 0.167
L 0.80 1.20 0.031 0.047
α
10
°
10
°
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw17
Packaging Information
SOT-89-5
Millimeters Inches
Dim
Min. Max. Min. Max.
A 4.40 4.60 0.17 0.18
B 4.05 4.25 0.16 0.17
C 1.50 1.70 0.06 0.07
D 1.30 1.50 0.05 0.06
E 2.40 2.60 0.09 0.1
F 0.80 - 0.03 G 3.00 REF 0.12 REF
H 1.50 REF 0.06 REF
I 0.40 0.52 0.01 0.02
J 1.40 1.60 0.05 0.06
K 0.35 0.41 0.01 0.02
L 5 TYP 0.2 TYP
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw18
TO-252( Reference JEDEC Registration TO-252)
Millimeters Inches
Dim
Min. Max. Min. Max.
A 2.18 2.39 0.086 0.094
A1 0.89 1.27 0.035 0.050
b 0.508 0.89 0.020 0.035
b2 5.207 5.461 0.205 0.215
C 0.46 0.58 0.018 0.023
C1 0.46 0.58 0.018 0.023
D 5.334 6.22 0.210 0.245
E 6.35 6.73 0.250 0.265
e1 3.96 5.18 0.156 0.204
H 9.398 10.41 0.370 0.410
L 0.51 0.020
L1 0.64 1.02 0.025 0.040
L2 0.89 2.032 0.035 0.080
L2
D
L1
b
b2
E
C1
A
H
L
C
A1
e1
Packaging Information
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw19
Packaging Information
TO-252-5
Millimeters Inches
Dim
Min. Max. Min. Max.
A 6.40 6.80 0.25 0.26
B 5.20 5.50 0.20 0.21
C 6.80 7.20 0.26 0.27
D 2.20 2.80 0.08 0.11
P 1.27 REF 0.05 REF
S 0.50 0.80 0.02 0.03
H 2.20 2.40 0.08 0.09
J 0.45 0.55 0.01 0.02
K 0 0.15 0 0.006
L 0.90 1.50 0.03 0.06
M 5.40 5.80 0.21 0.22
L
K
J
H
B
A
C
M
D
PS
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw20
Physical Specifications
Pre-heat temperature
183 C
Peak temperature
Time
°
temperature
Classification Reflow Profiles
Convection or IR/
Convection
VPR
Average ramp-up rate(183°C to Peak) 3°C/second max. 10 °C /second max.
Preheat temperature 125 ± 25°C)
120 seconds max
Temperature maintained above 183°C
60 – 150 seconds
Time within 5°C of actual peak temperature
10 –20 seconds 60 seconds
Peak temperature range
220 +5/-0°C or 235 +5/-0°C 215-219°C or 235 +5/-0°C
Ramp-down rate
6 °C /second max. 10 °C /second max.
Time 25°C to peak temperature
6 minutes max.
Package Reflow Conditions
pkg. thickness
≥≥≥≥
2.5mm
and all bgas
pkg. thickness < 2.5mm and
pkg. volume
≥≥≥≥
350 mm³
pkg. thickness < 2.5mm and pkg.
volume < 350mm³
Convection 220 +5/-0 °C Convection 235 +5/-0 °C
VPR 215-219 °C VPR 235 +5/-0 °C
IR/Convection 220 +5/-0 °C IR/Convection 235 +5/-0 °C
Terminal Material Solder-Plated Copper (Solder Material : 90/10 or 63/37 SnPb)
Lead Solderability Meets EIA Specification RSI86-91, ANSI/J-STD-002 Category 3.
Reference JEDEC Standard J-STD-020A APRIL 1999
Reflow Condition (IR/Convection or VPR Reflow)
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw21
Re liability test pro gra m
Test item Method Description
SOLDERABILITY MIL-STD-883D-2003
245°C , 5 SEC
HOLT MIL-STD-883D-1005.7
1000 Hrs Bias @ 125 °C
PCT JESD-22-B, A102
168 Hrs, 100 % RH , 121°C
TST MIL-STD-883D-1011.9
-65°C ~ 150°C, 200 Cycles
ESD MIL-STD-883D-3015.7 VHBM > 2KV, VMM > 200V
La tch-U p JESD 78 10m s , Itr > 100mA
Carrier Tape
A
J
B
T2
T1
C
t
Ao
E
W
Po
P
Ko
Bo
D1
D
F
P1
Copyright ANPEC Electronics Corp.
Rev. A.9 - May., 2003
APL5501/2/3
www.anpec.com.tw22
Application Carrier Width Cover Tape Width Devices Per Reel
SOP- 8 12 9.3 2500
SOT- 89 12 9.3 1000
SOT- 223 12 9.3 2500
TO- 252 16 13.3 2500
Anpec Electronics Corp.
Head Office :
5F, No. 2 Li-Hsin Road, SBIP,
Hsin-Chu, Taiwan, R.O.C.
Tel : 886-3-5642000
Fax : 886-3-5642050
Taipei Branch :
7F, No. 137, Lane 235, Pac Chiao Rd.,
Hsin Tien City, Taipei Hsien, Taiwan, R. O. C.
Tel : 886-2-89191368
Fax : 886-2-89191369
Customer Service
Reel Dimensions
Cover Tape Dimensions
Application
A B C J T1 T2 W P E
330 ± 1 62 +1.5 12.75+ 0.15 2 ± 0.5 12.4 ± 0.2 2 ± 0.2 12± 0. 3 8± 0.1 1.75±0.1
F D
D1 Po P1 Ao Bo Ko t
SOP- 8
5.5± 1 1.55 +0.1 1.55+ 0.25 4.0 ± 0.1 2.0 ± 0.1 6.4 ± 0.1 5.2± 0. 1 2 .1± 0.1 0.3±0.013
Application
A B C J T1 T2 W P E
178 ±1 70 ± 2 13.5 ± 0.15 3 ± 0.15 14 ± 2 1.3 ± 0.3
12 + 0.3
12 - 0.1
8 ± 0.1 1 .75± 0.1
F D D1 Po P1 Ao Bo Ko t
SOT-89
5.5 ± 0.05 1.5± 0.1 1 .5± 0.1 4.0 ± 0.1 2.0 ± 0.1 4 .8 ± 0.1 4.5± 0.1 1.80± 0.1 0.3±0.013
Application
A B C J T1 T2 W P E
330±162±1.5
12.75
±
0.15
2 ± 0.6 12.4 +0.2 2± 0.2 12 ± 0.3 8 ± 0.1 1 .75± 0.1
F D D1 Po P1 Ao Bo Ko t
SOT-223
5.5 ± 0.05 1.5+ 0.1 1.5+ 0.1 4.0 ± 0.1 2.0 ± 0.05 6.9 ± 0.1 7.5± 0.1 2 .1± 0.1 0.3±0.05
Application
A B C J T1 T2 W P E
330 ±3 100 ± 2 13 ± 0. 5 2 ± 0.5
16.4 + 0.3
-0.2
2.5± 0.5
16+ 0.3
- 0.1
8 ± 0.1 1 .75± 0.1
F D D1 Po P1 Ao Bo Ko t
TO-252
7.5 ± 0.1 1.5 + 0.1 1 .5± 0.25 4.0 ± 0.1 2.0 ± 0.1 6 .8 ± 0.1 10.4± 0.1 2 .5± 0.1 0.3±0.05
Loading...