AKAI MPK49 Operating Manual
TABLE OF CONTENTS
FRONT PANEL OVERVIEW .......................................................................................................... 1
REAR PANEL OVERVIEW ............................................................................................................ 3
HOOKUP DIAGRAM ...................................................................................................................... 4
DISPLAYING INFORMATION........................................................................................................ 6
OCTAVE AND TRANSPOSITION ........................................................................................... 6
NOTE....................................................................................................................................... 6
NOTE AFTERTOUCH (Channel Pressure).............................................................................. 6
CONTROL CHANGE ............................................................................................................... 6
CONTROL AFTERTOUCH...................................................................................................... 7
MIDI MACHINE CONTROL COMMAND (MMC)...................................................................... 7
PREVIEWING.......................................................................................................................... 7
ABOUT MODES ............................................................................................................................. 8
PRESET MODE.............................................................................................................................. 9
PAGE 1 – LOAD PRESET....................................................................................................... 9
PAGE 2 – SAVE/COPY PRESET............................................................................................ 9
PAGE 3 – NAME PRESET ...................................................................................................... 9
EDIT MODE .................................................................................................................................. 10
EDIT MODE PARAMETERS .......................................................................................... 11
EDITING THE KEYBOARD ................................................................................................... 12
KEYBOARD OCTAVE .................................................................................................... 12
KEYBOARD AFTERTOUCH .......................................................................................... 12
KEYBOARD VELOCITY ................................................................................................. 12
EDITING THE PADS ............................................................................................................. 13
NOTE PARAMETERS .................................................................................................... 14
PROGRAM CHANGE PARAMETERS ........................................................................... 15
EDITING KNOBS AND FADERS........................................................................................... 16
CONTROL CHANGE PARAMETERS ............................................................................ 17
AFTERTOUCH PARAMETERS...................................................................................... 18
INCREMENT/DECREMENT PARAMETERS (knobs only)............................................. 19
EDITING BUTTONS .............................................................................................................. 20
CONTROL CHANGE PARAMETERS ............................................................................ 20
PROGRAM CHANGE PARAMETERS ........................................................................... 21
EDITING THE ARPEGGIATOR............................................................................................. 22
ARPEGGIO PARAMETERS – TYPE, RANGE, BUTTON MODE................................... 23
ARPEGGIO PARAMETERS – GATE, SWING ............................................................... 24
EDITING NOTE REPEAT ...................................................................................................... 25
NOTE REPEAT BUTTON MODE ................................................................................... 26
NOTE REPEAT PARAMETERS – GATE, SWING......................................................... 26
EDITING TIME DIVISION ...................................................................................................... 27
DEFAULT TIME DIVISION ............................................................................................. 27
BUTTON MODE ............................................................................................................. 27
EDITING THE PITCH BEND WHEEL.................................................................................... 28
EDITING THE MODULATION WHEEL.................................................................................. 29
EDITING TRANSPORT CONTROL....................................................................................... 30
EDITING TAP TEMPO........................................................................................................... 30
EDITING SUSTAIN PEDAL INPUT ....................................................................................... 31
EDITING EXPRESSION PEDAL INPUT................................................................................ 32
GLOBAL MODE ........................................................................................................................... 33
KILL MIDI – Page1................................................................................................................. 33
MIDI COMMON CHANNEL – Page 2 .................................................................................... 33
LCD CONTRAST – Page 3.................................................................................................... 34
PAD SENSITIVITY – Page 4 ................................................................................................. 34
PAD VELOCITY CURVE – Page 5........................................................................................ 34
PAD THRESHOLD – Page 6 ................................................................................................. 35
KEYBOARD TRANSPOSITION – Page 7.............................................................................. 35
MIDI CLOCK – Page 8........................................................................................................... 35
TAP TEMPO AVERAGE – Page 9......................................................................................... 35
SAVE GLOBAL – Page 10..................................................................................................... 36
SYSEX TX – Page 11............................................................................................................ 36
VERSION – Page 12 ............................................................................................................. 36
PROGRAM CHANGE MODE ....................................................................................................... 37
PROG CHANGE (Program Change) ..................................................................................... 37
PROG+BANK (Program Change with Bank Change)............................................................ 37
FREQUENTLY ASKED QUESTIONS .......................................................................................... 38
TROUBLESHOOTING.................................................................................................................. 39
TECHNICAL SPECIFICATIONS .................................................................................................. 40
CONTACT INFORMATION .......................................................................................................... 40
FRONT PANEL OVERVIEW
1. LCD – The display is used for navigating
menus, displaying data, and affecting change
on MPK49’s options and parameters.
2. [VALUE] (Push to Enter) – This dial is used
to increment and decrement Presets,
parameter values and settings. This dial also
functions as an [ENTER] button when it is
pressed down.
3. [<] AND [>] BUTTONS – These buttons are
used to navigate through the fields of menus
and options. The [<] button also functions as
a [CANCEL] button.
4. [PRESET] – This button calls up Preset
Mode. You can select and recall different
Preset programs in this mode.
5. [EDIT] – This button calls up Edit Mode,
which allows you to edit the behavior of the
keyboard, pads, knobs, buttons, faders and
default settings for each preset.
6. [GLOBAL] – This button calls up Global
Mode, where MIDI reset commands and
global system preferences are set.
7. [PREVIEW] – This button allows you to see
what value will be sent by a controller, without
actually sending the value. This gives you
precise control over your parameters and
helps avoid erroneous controller data being
sent to your devices due to the physical
position of the controller. This is especially
useful when switching between control banks
where, for example, the physical position of a
fader may not correspond to the last value
sent by the controller. Holding down
[PREVIEW] allows you to view the original
value and adjust the physical position of the
fader as necessary before transmitting any
values.
8. [PROGRAM CHANGE] – Pressing this
button will enter Program Change mode. In
this mode, you can send a Program Change
or Program with Bank Change message to a
hardware or software module.
9. TRANSPORT CONTROL BUTTONS –
These five buttons are dedicated buttons for
sending transport control commands. The
transport control buttons can be set to
transmit either MMC (MIDI Machine Control),
MMC/MIDI SysEx, MIDI START/STOP or
pre-assigned MIDI CC values.
10. 8 ASSIGNABLE KNOBS –Each 360-degree
knob can be used to send continuous control
data to a desktop audio workstation or
external MIDI device.
11. 8 ASSIGNABLE FADERS – Each fader can
be used to send continuous control data to a
desktop audio workstation or external MIDI
device.
12. 8 ASSIGNABLE BUTTONS – These buttons
can be used as MIDI CC switches or Program
Change switches. They can function in
momentary or toggle modes. When [TIME
DIVISION] has been activated, these 8
buttons are used to set the time division of
the Arpeggiator and Note Repeat features.
13. [CONTROL BANK] – The MPK49 features 3
independent banks of continuous controllers.
Effectively, this allows you to control up to 72
independent parameters with the knobs,
faders and buttons on the MPK49. The
[CONTROL BANK] button is used to switch
among the 3 banks. The LEDs above the
button will reflect the currently selected
control bank.
1
14. 12 MPC PRESSURE AND VELOCITY
SENSITIVE PADS – The pads can be used
to trigger drum hits or samples on your
software or hardware module or can be
configured to send Program Change
messages. The pads are pressure and
velocity sensitive, which makes them very
responsive and intuitive to play.
15. PAD BANK buttons – These 4 buttons
switch among pad banks A, B, C, D. Each
bank can address a unique set of 12 sounds,
giving you access of up to 48 different
sounds you can trigger with the pads.
The currently selected pad bank will
be indicated on the LCD display
16. [FULL LEVEL] – When [FULL LEVEL] is
activated, the pads always play back at a
maximum velocity (127), no matter how hard
or soft you hit them.
17. [12 LEVEL] – When [12 LEVEL] is activated,
you can use the 12 pads to change a
selected sound’s velocity in 12 steps. When
you press the [12 LEVEL] button, the last pad
that was hit gets mapped to all 12 pads. The
pads will now output the same note number
and pressure controller as the initial pad, but
the velocity is
fixed at the values
shown in the
diagram on the
right, regardless
of how hard you
hit them. This
allows you to have
more control over
the velocity of a
sound.
18. [NOTE REPEAT] – Holding this button while
striking a pad causes the pad to retrigger at a
rate based on the current Tempo and Time
Division settings. The Note Repeat feature
can be synced to an internal or external MIDI
Clock source. [NOTE REPEAT] can function
as a latching or momentary button
19. [TIME DIVISION] – This button is used to
specify the rate of the Note Repeat and
Arpeggiator features. When [TIME
DIVISION] is activated, you can press one of
the 8 switches to specify a time division.
[TIME DIVISION] can function as a
momentary or toggle button.
Please note that while [TIME DIVISION] is
active, the 8 assignable buttons will not
function as MIDI CC or Program Change
switches until [TIME DIVISION] has been deactivated.
20. [ARP ON/OFF] – This button enables and
disables the internal Arpeggiator. The
Arpeggiator will only function on notes being
played on the keyboard. The Arpeggiator
feature on the MPK49 works in conjunction
with the Tempo and Time Division settings,
which specify the rate of arpeggiation.
Please note that the Arpeggiator can be
synced either to an internal or external MIDI
Clock source (such as a software DAW or a
MIDI device).
21. [LATCH] – This button works in conjunction
with the Arpeggiator. When the Arpeggiator
is turned on and [LATCH] has been enabled,
you can hold down a combination of keys -the Arpeggiator will memorize and continue to
arpeggiate these notes, even if you depress
the keys. There are a couple of ways to use
the [LATCH] function:
a. While holding down the keys, you can
add more notes to the sequence by
pressing down additional keys.
b. If you depress the keys, release them,
and then press down a new
combination of notes, the Arpeggiator
will memorize and arpeggiate the new
notes.
22. [OCTAVE + / -] – These buttons can be used
to shift the keyboard’s range up and down.
The display will indicate which octave you
have shifted to. If both buttons are pressed
at the same time, the octave shift will reset to
0.
23. [TAP TEMPO] – This button allows you to tap
in a new tempo. If the preset is reloaded, the
tempo will revert to the saved tempo value.
(Please note that a preset’s default tempo
can be set in Edit Mode). Tap Tempo does
not work when the MPK49 is set to External
sync.
24. PITCH BEND WHEEL – Transmits MIDI
Pitch Bend information on a selected MIDI
channel and port.
25. MODULATION WHEEL – This wheel can be
used to transmit continuous controller data.
By default, the modulation wheel will transmit
MIDI CC #01.
2
REAR PANEL OVERVIEW
1. DC POWER ADAPTER INPUT – Plug in a
6V–1A DC power adapter if you do not wish
to power the MPK49 through the USB
connection.
2. POWER ADAPTER RESTRAINT – You can
secure the power adapter cord to this
restraint to prevent accidental unplugging.
3. USB CONNECTION – Plug a standard USB
cable into this outlet and into the USB port of
your computer. The computer’s USB port will
provide power to the MPK49. This
connection is used to send and receive MIDI
data to and from your computer and may also
be used to send MIDI data from your
computer to a device attached to the MIDI
OUT port of the MPK49.
4. MIDI OUT – Use a five-pin MIDI cable to
connect the MIDI OUT of the MPK49 to the
MIDI IN of an external device.
5. MIDI IN – Use a five-pin MIDI cable to
connect the MIDI OUT of an external MIDI
device to the MIDI IN of the MPK49.
6. SUSTAIN PEDAL – Connect a ¼” TS sustain
pedal to this input. We recommend using the
Alesis Sustain Pedal.
7. EXPRESSION PEDAL INPUT – Connect a
¼” TRS expression pedal to this input. We
recommend using the Alesis F2 expression
pedals.
8. KENSINGTON LOCK – The unit may be
secured to a table or surface using this
Kensington Lock slot.
3
HOOKUP DIAGRAM
Please refer to the following scenario for connecting the MPK49.
EXTERNAL SOUND MODULE
COMPUTER
POWER
ADAPTER
EXTERNAL
MIDI DEVICE
SUSTAIN
PEDAL EXPRESSION
PEDAL
MIDI from MPK49 to
computer
MIDI from external MIDI
device connected to MIDI IN
port of MPK49
MIDI from computer to
external sound module
connected to MIDI OUT port
of MPK49
1. Connect a USB cable from your computer to the MPK49. The unit will be powered through the
USB connection. Alternatively, if you do not wish to use a computer in your setup or if you wish
to power the MPK49 externally, please plug in a 6V-1A DC power adapter (optional).
2. If you would like to use an external sound module, connect a 5-pin MIDI cable from the MIDI OUT
of the MPK49 to the MIDI IN of the external device.
3. If you would like to use another MIDI controller in your setup, connect a 5-pin MIDI cable from the
MIDI OUT of the controller to the MIDI IN of the MPK49.
4
1. Make sure that the MPK49 and all external devices are connected and that the USB
2. In your software application, you will need to set the MPK49 as a default MIDI input
3. If you would like to use tempo-synced features, such as Note Repeat and Arpeggiator,
The operation of the MIDI OUT port changes depending on whether or not a USB cable is
connected to the MPK49.
• USB cable connected:
• USB cable not connected:
A NOTE ABOUT USING THE MPK49 WITH SOFTWARE
cable is connected to your computer before opening any software applications on your
computer with which you might want to use the MPK49. If the unit is not plugged in
before, your software application might not recognize the MPK49 as an available
device.
device. This is usually done in the MIDI section of the Preferences menu.
you will also need to slave the MPK49 to a MIDI Clock generated by your software
DAW. Make sure that your software is set up to send MIDI clock to the MPK49 and that
the unit’s MIDI Clock setting is set to “External” (see Global Mode). This will ensure that
the Arpeggiator and Beat Repeat are synchronized to the tempo selected in your
software DAW.
IMPORTANT
MIDI data from your computer is passed to the MIDI OUT port. When a USB cable is
connected, you should activate "MIDI echo" in your sequencer if you want the MPK49 to
control another external device.
Whatever you play on the MPK49 is sent to the MIDI OUT port.
Note: If you have another device connected to the MPK49's MIDI IN port, that device's
MIDI information will be ignored.
5
DISPLAYING INFORMATION
As you are working with the MPK49, the LCD will help you keep track of what values and parameters are
entered and sent to external devices. There are several kinds of information that the MPK49 will display
while in use: OCTAVE, TRANSPOSITION, NOTE, AFTERTOUCH (Channel Pressure), CONTROL
CHANGE, MIDI MACHINE CONTROL (MMC), and PREVIEW MODE information.
OCTAVE AND TRANSPOSITION
When using the keyboard, the LCD will display the
current octave and any transposition setting which
you may have applied.
OCTAVE SHIFT
Note: The octave settings will apply to individual
presets while transposition will affect all presets
globally.
NOTE
When a PAD is hit, the MPK49 will output MIDI
MIDI PORT
AND CHANNEL
NOTE
INDICATOR
TRANSPOSITION
Note On messages to trigger sounds on your DAW
or external device. Each pad can have a MIDI Note
Number associated with it. When you hit a pad, the
screen will display the MIDI Note Number, the MIDI
Port and Channel which the pad is using, as well as
the pad bank and velocity (how hard you hit the
pad).
Please see ‘Editing Pads’( page 13) for more
information on MIDI Notes and Pads.
NOTE AFTERTOUCH (Channel Pressure)
PAD BANK
When enabled, AFTERTOUCH is MIDI data sent
when pressure is applied to one of the pads after it
MIDI NOTE
NUMBER
NOTE
VELOCITY
VELOCITY IS
ALSO DISPLAYED
WITH BAR METER.
AFTERTOUCH
VALUE
has been struck and while it is being held down. It
will be displayed on the far right of the display as
you apply pressure to the pad.
CONTROL CHANGE
When a KNOB or FADER is used, the MPK49 will
output MIDI Control Change data. This data is used
to change certain parameters on your DAW or
external sound module. When you move a knob or
fader, the screen will indicate the Control Change
(CC) Number, value, and MIDI Channel.
Please see ‘Editing Knobs and Faders’ (page
16) for more information on Control Change.
MIDI PORT
AND CHANNEL
PAD BANK
CONTROL CHANGE
INDICATOR
CONTROL CHANGE
NUMBER
AFTERTOUCH
VALUE IS ALSO
DISPLAYED WITH BAR
METER
CONTROL CHANGE
VALUE
VALUE IS ALSO
DISPLAYED WITH
BAR METER.
6
CONTROL AFTERTOUCH
The knobs and faders on the MPK49 can also be
set to transmit AFTERTOUCH information.
Please see ‘Editing Knobs and Faders’ (page
MIDI PORT
AND CHANNEL
AFTERTOUCH
INDICATOR
AFTERTOUCH
VALUE
16) for more information on setting knobs and
faders to transmit Aftertouch.
MIDI MACHINE CONTROL COMMAND (MMC)
PAD BANK
MIDI MACHINE CONTROL (MMC) is commonly
MMC
COMMAND
VALUE IS ALSO
DISPLAYED WITH
BAR METER.
used to send transport control messages to
hardware record or playback machines. For
example: Pressing [PLAY] on the MPK49 sends an
MMCPLAY message to a connected multi-track
recorder, which begins playing. When [STOP] is
pressed on the MPK49, the deck also stops.
PREVIEWING
When the [PREVIEW] button is held down, and a
fader or knob is moved, the LCD displays the
CONTROL
CHANGE NUMBER
screen on the right. The display shows the
assigned event and the last sent value of moved
knob or fader. While the [PREVIEW] button is held,
NEW VALUE
the fader of knob will not be transmitting any
information until [PREVIEW] is released and the
fader or knob is used again. At that point, the fader
or knob will begin transmitting from the value
selected in the New Value field while in Preview
mode.
THE ADVANTAGES OF PREVIEWING
The [PREVIEW] button allows you to see what value will be sent by a controller, without actually sending the
value. This gives you precise control over your parameters and helps avoid erroneous controller data being
sent to your devices due to the physical position of the controller. For example, imagine that slider S1 is
being used to send three different MIDI CC numbers, depending on the control bank which you are currently
in. Let’s assume that S1 is assigned to MIDI CC#10 in control bank A and MIDI CC#11 in control bank B.
While in control bank A, you adjust S1 (MIDI CC#10) to a value of 40. Now you switch over to control bank B
and adjust S1 (MIDI CC#11) to a value of 80. If you now switch back to control bank A and try to adjust S1
(MIDI CC#10), you will notice that the transmitted values will begin at 80 (instead of 40), due to the physical
location of the slider. To prevent this, you can hold down [PREVIEW] and move S1 back to a value of 40
(which will be shown in the “Last” value readout on the display). The slider will not be transmitting information
while the [PREVIEW] button is held down. Once you reset the slider back to its “Last” value, you can release
the [PREVIEW] button. Adjusting S1 (MIDI CC#10) will now give you a nice starting point at a value of 40.
LAST VALUE
SENT
LAST VALUE
SENT
NEW VALUE
7
ABOUT MODES
The MPK49 has four different modes of operation. Each mode can be accessed by pressing the
corresponding button on the MPK49. Following is a short description of each mode:
Preset Mode
This mode allows you to load, save and copy Presets. A Preset is a
collection of information about how different faders, knobs, and pads will
behave. Using Presets allows you to save different configurations so you
can quickly load them when you need them, without having to reprogram the
MPK49 every time.
Edit Mode
Global Mode
Program Change Mode
(page 9)
This mode allows you to edit the configuration of the MPK49. Edit Mode is a
powerful tool for customizing your set-up. In this mode, you can make
changes to how the keyboard, pads, knobs and faders are behaving. For
example, you may wish to have a fader or a knob transmit only a limited
range of MIDI data, or you may wish to have a pad that transmits on a
different MIDI Channel. You can change these and other various parameters
in Edit Mode.
(page 10)
This mode allows you to set global parameters and make general changes to
how your MPK49 is functioning. For example, in Global Mode you can
change how the pads respond to the touch, or change the brightness of the
LCD screen. The parameters that you can modify in Global Mode also
include controller resets, pad response curves, display brightness, and more.
(page 31)
This mode allows you to transmit various Program Change messages. In
this mode, you can tell your DAW or an external device to switch to a
different program bank of sounds. This way, you can avoid having to
manually switch between different programs on your DAW or external device.
(page 35)
8
PRESET MODE
What is a Preset?
A Preset is a collection of information about how the MPK49’s keyboard,
sliders, knobs, and pads will behave. Using Presets allows you to save
different configurations so you can quickly load them when you need them,
without having to reprogram the MPK49 every time.
The MPK49 features different Preset banks that you can load and write to. When you turn on the MPK49, it
PRESET NAME PRESET NUMBER
will automatically go into Preset Mode and Preset 1 will be displayed on the screen. You can also press
the [PRESET] button at any time to call up this mode. In Preset Mode you can load, save/copy and
rename Presets – each of these functions can be accessed through the 3 different pages. You can
navigate between these pages with the [<] and [>] buttons.
PAGE 1 – LOAD PRESET
1. While you are in Preset Mode, you can change Presets with the [VALUE]
dial below the screen. Turning the dial increments or decrements the current
Preset number and displays the screen on the right:
When you do this, you will notice that ‘PRESS ENTER’ will begin to blink.
2. Pressing [ENTER] loads the selected Preset. Pressing [<] button or
[PRESET] button cancels and returns you to the Preset that was last
selected.
PAGE 2 – SAVE/COPY PRESET
In Preset Mode, you can also save and copy a Preset to a new location. This
allows you to save any changes that you have made to the Preset.
Note that if you are saving the Preset to the same location (same preset number)
the screen will say ‘SAVE TO’ and if you are saving to a different location
(different preset number), the screen will display ‘COPY TO’.
1. While you are in
above.
Preset Mode, press [>] button until you see the ‘SAVE TO’ screen similar to the one shown
DESTINATION
2. You can select the location where you want to save the Preset by turning the [VALUE] knob.
When you do this, you will notice that the ‘PRESS ENTER’ segment will begin to blink.
3. Press [ENTER] to save current Preset to the destination. Pressing [<] button or [PRESET] button cancels the
operation and returns you to the Preset play mode.
PAGE 3 – NAME PRESET
While you are in Preset Mode, you can also change the Preset name. This way
you can assign specific names to different Presets so you can quickly identify
and access different controller configurations.
1. To name or rename the Preset, press the [>] button until you see ‘Preset
Name’ displayed on the screen.
You will notice that the first letter of the name will begin blinking.
2. Turn the [VALUE] dial to change the blinking character.
ENTER PRESET NAME IN
THIS FIELD
3. To move between the characters, use [<] and [>] buttons.
4. When done, press [PRESET] again. The name will be saved.
9
EDIT MODE
Pressing the [EDIT] button calls up
Edit Mode. In this mode, you can
edit the settings of the currently
selected Preset. The settings vary
depending on the controller you are
editing and are described below.
Please note that the changes you
make will only apply to the currently
selected Preset.
1. Press the [EDIT] button.
2. To select the controller you wish to edit, simply engage it – this will
prompt the screen to display the properties of the particular controller
(Page 1).
3. If there are multiple properties for the selected controller, turn the
[VALUE] dial to select the property you wish to edit. Press [ENTER] to
view the parameters of the selected property, if available (Page 2).
4. To move between the parameter fields on Page 2, use the [<] and [>]
buttons. To change the values of the fields, turn the [VALUE] dial.
5. When finished editing the controller, press [ENTER] to accept the change
or press [<] to cancel.
You can use the example screenshot on the right to
help you determine where the Page 2 parameters
described on the following page will appear on the
screen.
NAVIGATING EDIT MODE
FIELD 1
FIELD 2
FIELD 3
FIELD 4
10
EDIT MODE PARAMETERS
CONTROLLER SELECTED PAGE 1 PAGE 2
KEYBOARD
PADS
KNOBS AND FADERS
BUTTONS
ARP ON/OFF
NOTE REPEAT
TIME DIVISION
PITCH BEND WHEEL
MODULATION WHEEL
TRANSPORT
TAP TEMPO
EXPRESSION PEDAL
SUSTAIN PEDAL
OCTAVE
AFTERTOUCH
VELOCITY
NOTE
PROGRAM CHANGE
CONTROL CHANGE
AFTERTOUCH
CONTROL CHANGE
PROGRAM CHANGE
TYPE/RANGE/TOGGLE
GATE/SWING
TOGGLE/MOMENTARY
GATE/SWING
DIVISION
PITCH BEND
MODULATION WHEEL
TRANSPORT FUNCTION
TEMPO
CNTL CHANGE
AFTERTOUCH
MIDI CC
DRUM PAD
NOTE REPEAT
TIME DIV
TAP TEMPO
BANK CHANGE
PLAY/STOP
PLAY/RECORD
ARP ON/OFF
ARP LATCH
SUSTAIN
KEYBOARD MIDI CHANNEL (field 1)
UP/DOWN (field 4)
KEYBOARD MIDI CHANNEL (field 1)
ON/OFF BEHAVIOR (field 4)
KEYBOARD MIDI CHANNEL (field 1)
ON/OFF BEHAVIOR (field 4)
MIDI CHANNEL (field 1)
NOTE NUMBER (field 2)
ON/OFF BEHAVIOR (field 3)
PRESSURE BEHAVIOR (field 4)
MIDI CHANNEL (field 1)
PROGRAM CHANGE NUMBER (field 2)
BANK M (MSB) (field 3)
BANK L (LSB) (field 4)
MIDI CHANNEL (field 1)
CC NUMBER (field 2)
RANGE – MINIMUM VALUE (field 3)
RANGE – MAXIMUM VALUE (field 4)
MIDI CHANNEL (field 1)
CC NUMBER (field 2)
RANGE – MINIMUM VALUE (field 3)
RANGE – MAXIMUM VALUE (field 4)
MIDI CHANNEL (field 1)
CC NUMBER (field 2)
BUTTON MODE (field 4)
MIDI CHANNEL (field 1)
PROGRAM CHANGE NUMBER (field 2)
BANK M (MSB) (field 3)
BANK L (LSB) (field 4)
ARPEGGIO TYPE (field 2)
ARPEGGIO RANGE (field 3)
ARPEGGIO TOGGLE BEHAVIOR (field 4)
ARPEGGIO GATE VALUE (field 2)
ARPEGGIO SWING VALUE (field 4)
BUTTON MODE (field 2)
NOTE REPEAT GATE VALUE (field 2)
NOTE REPEAT SWING VALUE (field 4)
DEFAULT TIME DIVISION (field 2)
BUTTON MODE (field 4)
MIDI CHANNEL (field 1)
MIDI CHANNEL (field 1)
CC NUMBER (field 2)
RANGE – MINIMUM VALUE (field 3)
RANGE – MAXIMUM VALUE (field 4)
MMC, MIDI, MMC/MIDI, or CTRL (field 2)
BPM (field 2)
MIDI CHANNEL (field 1)
CC NUMBER (field 2)
RANGE – MINIMUM VALUE (field 3)
RANGE – MAXIMUM VALUE (field 4)
MIDI CHANNEL (field 1)
RANGE – MINIMUM VALUE (field 3)
RANGE – MAXIMUM VALUE (field 4)
MIDI CHANNEL (field 1)
CC NUMBER (field 2)
BUTTON MODE (field 4)
PAD NUMBER (field 4)
11
EDITING THE KEYBOARD
When editing the keyboard, please note that the changes will affect all the keys on the MPK49. The
keyboard properties you can edit include MIDI Channel, Octave, Aftertouch, and Velocity.
MIDI CHANNEL – This is the MIDI Channel on which the keyboard will be transmitting information.
OCTAVE – This is the default octave shift that will be applied to the keyboard when the current Preset is loaded.
AFTERTOUCH – Aftertouch describes pressure applied to the keys after they have been pressed. Aftertouch can
often be used to control the vibrato, sustain or decay of a sound. The Aftertouch setting on the MPK49 can be set to
either “On” or “Off”. When set to “Off”, the MPK49 will ignore Aftertouch.
VELOCITY – Velocity describes how hard the keys are struck. Most often, velocity is directly mapped to the
perceived loudness of a sound; so the harder you play the keys, the louder the sound will be. The Velocity setting on
the MPK49 can be set to either “On” or “Off”. When set to “On”, the keyboard will detect how hard the keys are
pressed and translate these values into corresponding MIDI velocities. When set to “Off”, MPK49 will output a
constant MIDI velocity, no matter how hard the keys are pressed.
SELECT PROPERTY
1. To edit the keyboard, press the [EDIT] button to enter Edit Mode.
2. Now select the keyboard for editing by pressing one of the keys.
3. You will see Page 1 displayed on the screen (shown on the left).
4. Turn the [VALUE] dial to select the property you wish to edit
(Octave, Aftertouch, Velocity).
5. Press [ENTER] to edit the selected property.
PRESS ENTER TO EDIT
KEYBOARD OCTAVE
MIDI CHANNEL FIELD
1. In the first field of this page, you can set the keyboard’s MIDI channel
field by turning the [VALUE] dial.
2. Press [>] to edit the Octave shift.
3. The Octave shift field will begin to blink. Set the shift by turning the
[VALUE] dial (default shift is set to “0”).
OCTAVE SHIFT FIELD
4. When finished, press [ENTER] to return to Page 1.
KEYBOARD AFTERTOUCH
MIDI CHANNEL FIELD
1. You can set the keyboard’s MIDI channel field by turning the [VALUE]
dial.
2. When done, press [>] to edit Aftertouch.
3. The Aftertouch field will begin to blink. Turn the [VALUE] dial to turn
Aftertouch “On” or “Off” (default is set to “On”).
4. When finished, press [ENTER] to return to Page 1.
AFTERTOUCH FIELD
KEYBOARD VELOCITY
MIDI CHANNEL FIELD
VELOCITY FIELD
1. You can set the keyboard’s MIDI channel field by turning the [VALUE]
dial.
2. When done, press [>] to edit Velocity.
3. The Velocity field will begin to blink. Turn the [VALUE] dial to turn
Velocity “On” or “Off” (default is set to “On”).
4. When finished, press [ENTER] to return to Page 1.
12
Loading...