AEG EFC 9671, EFC 6671 Manual [pt]

0 (0)

User manual Manual de instrucciones Manual de instruções

EFC 9671-6671

Welcome to the world of Electrolux

Thank you for choosing a first class product from Electrolux, which hopefully will provide you with lots of pleasure in the future. The Electrolux ambition is to offer a wide variety of quality products that make your life more comfortable. You find some examples on the cover in this manual. Please take a few minutes to study this manual so that you can take advantage of the benefits of your new machine. We promise that it will provide a superior User Experience delivering Ease-of-Mind.

Good luck!

electrolux 3

4 electrolux contents
Contents
GB
Safety warnings ................................	5
Description of the Appliance .............	7
Control Panel ...................................	8
Maintenance and Care ...................	11
Special accessories ........................	15
Something Not Working .................	15
Installation ......................................	16

The following symbols are used in this user manual:

Important information concerning your personal safety and information on how to avoid damaging the appliance.

General information and tips.

Environmental information.

electrolux safety warnings 5

Safety warnings

•When used as an extractor unit, the hood must be fitted with a hose having preferably the same diameter as the outlet hole.

Should there already be a pipe of diameter 125 mm that ducts to the outside through the walls or roof, it is possible to use the 150/125 mm reduction flange provided. In this case the hood will be slightly noisier.

Attention: The hose is not supplied and must be purchased separately.

•The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of the range hood must be not less than 50cm from electric cookers and 65cm from gas or mixed cookers.

If the instructions for installation for the gas hob specify a greater distance, this must be adhered to.

•Before any cleaning or maintenance operation, disconnect the hood from the mains by removing the plug or disconnecting the home mains switch.

•The appliance is not intended for use by children or persons with impaired physical, sensorial or mental faculties, or if lacking in experience or knowhow, unless they are under supervision or have been trained in

the use of the appliance by a person responsible for their safety.

•Children should be monitored to ensure that they do not play with the appliance.

•Never use the hood without effectively mounted grating.!

•The hood must NEVER be used as a support surface unless specifically indicated.

•The premises must be sufficiently ventilated, when the kitchen hood is used together with other gas combustion devices or other fuels.

•The suctioned air must not be conveyed into a conduit used for the disposal of the fumes generated by appliances that combust gases or other fuels.

•The flaming of foods beneath the hood itself is severely prohibited.

•The use of exposed flames is detrimental to the filters and may cause a fire risk, and must therefore be avoided in all circumstances.

•Any frying must be done with care in order to make sure that the oil does not overheat and burst into flames.

•As regards the technical and safety measures to be adopted for fume discharging it is important to closely follow the relations provided by the competent authorities.

•The hood must be regularly cleaned on both the inside and outside (AT

6 electrolux safety warnings

LEAST ONCE A MONTH, it is in any event necessary to proceed in

GB accordance with the maintenance instructions provided in this manual)..

•Failure to follow the instructions as concerns hood and filter cleaning will lead to the risk of fires.

•Do not use or leave the hood without the lamp correctly mounted because of the possible risk of electric shocks.

•We decline any responsibility for any problems, damage or fires caused to the appliance as the result of the non-observance of the instructions included in this manual.

This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and Electronic Equipment (WEEE).

By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product.

The symbol on the product, or on the documents accompanying the product, indicates that this appliance may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.

Disposal must be carried out in accordance with local environmental regulations for waste disposal.

For more detailed information about treatment, recovery and recycling of this product, please contact your local city office, your household waste disposal service or the shop where you purchased the product.

Description of the Appliance

•The cooker hood is designed to extract unpleasant odours from the kitchen, it will not extract steam.

•The hood is supplied as an extractor unit and can also be used in recirculation mode by fitting a charcoal filter.

Extraction mode

•In this mode fumes are extracted to the outside via a hose connected to the coupling ring.

•In order to obtain the best performance the hose should have a diameter equal to the outlet hole.

Recirculation mode

•The air is filtered through a charcoal filter and returned to the kitchen.

•You will need an original charcoal filter for the recirculation mode. (See Special Accessories).

electrolux description of the appliance 7

Coupling ring

8 electrolux control panel

Control Panel

•Best results are obtained by using a low speed for normal conditions and a high speed when odours are more concentrated.

Turn the hood on a few minutes before you start cooking.

The hood should be left on after cooking for about 15 minutes or until all the odours have disappeared.

•The hood can also be commanded from the control panel or the remote control. (the remote control is a special accessory and is ordered separately).

•Correct ventilation: If the cooker hood is to work correctly there must be a low pressure in the kitchen. It is important to keep the kitchen windows closed and have a window in an adjacent room open.

•The control switches are located on the hood’s front panel

•The cooker hood is fitted with a sensor which, in the event of extreme variations in temperature, switches the appliance on automatically until the temperature of the environment surrounding the hood has been significantly reduced.

electrolux control panel 9

D1	D2	GB

1.Lights key ON/OFF:

This switch is used to turn the light fitted in the hood on and off.

2.Motor stand-by/OFF key:

Stand-by (dot “D2” on display is illuminated): all the commands are enabled for functioning, press the key for more than 1 second to turn the hood OFF. OFF (display off): and the commands with the exception of the ON/OFF lights key are disable. Press the key for more than 1 second to set the hood in Stand-by.

3.Selection and aspiration speed (power) and timer key: press to select the aspiration speed (power) or set the hood in stand-by in the sequence:1-2-3-1-

2-.....

Timer (ON/OFF): once the speed (power) has been selected, pressing successively for 2 seconds activates (ON – the dot “D2” on display is flashing) or deactivates (OFF) the timer function. This allows the aspiration speed (power) selected for a predetermined time to function:

Aspiration Speed (power) 1: 20 minutes Aspiration Speed (power) 2: 15 minutes Aspiration Speed (power) 3: 10 minutes After which the hood goes into stand-by.

4.Intensive aspiration (power) key (timed) ON (the dot “D1” on display is flashing)/OFF: press to select the intensive aspiration speed (power). It will function for 5 minutes after which the hood goes into stand-by.

Pressing before the five minutes have passed, the hood returns to the previously set speed.

5.Filters saturation reset key: see the relative text on the following pages.

6.Display

Note: if you have a remote control (special accessory) and the letter "b" appears on the display, you should replace the battery.

Should the hood or the controls fail to operate: disconnect the power supply for at least 5 seconds. After reconnecting the power supply wait 15 seconds and then check that the cooker hood is now operating correctly.

10 electrolux control panel

Grease and charcoal filter

maintenance indicator

This hood is fitted with a device that indicates when it is necessary to clean the grease filter or the charcoal filter (if the hood is used in the recirculation version with a charcoal filter).

On delivery, the hood is not supplied with a charcoal filter, so the saturation indicator will be disabled.

If the hood is to be used with a charcoal filter, the saturation indicator light must be enabled as follows:

Set the hood to "OFF".

Press buttons 4 and 5 simultaneously and hold them for 3 seconds. At first only the grease filter LED F will light up, but when the charcoal filter LED C lights up the saturation indicator will be enabled.

To disable it: Press buttons 4 and 5 again simultaneously and hold

them for 3 seconds, until the charcoal filter LED goes out.

Grease filter LED (F)

LED F will start to flash when it is time to clean the grease filter.

Cleaning will be necessary after 40 working hours. Always comply with the maintenance instructions for the grease filter.

Charcoal filter LED (C)

The charcoal filter LED C will start to flash when the charcoal filter needs to be replaced.

This operation is necessary after approximately 160 working hours.

Resetting the saturation indicator

After cleaning or replacing the filters, press button 5 for 3 seconds until the grease filter LED F or the charcoal filter LED C stops flashing.

electrolux maintenance and care 11

Maintenance and Care

•Before performing any maintenance operation, isolate the hood from the electrical supply by switching off at the connector and removing the connector fuse.

Or if the appliance has been connected through a plug and socket, then the plug must be removed from the socket.

Metal grease filter

•The purpose of the grease filters is to absorb grease particles which form during cooking and it must always be used, either in the external extraction or internal re-circulation function.

Attention: the metal grease filters must be removed and washed, either by hand or in the dishwasher, every four weeks.

Removing the metal grease filter

•Use the spring handle and remove the filter downward.

Hand washing

Soak grease filters for about one hour in hot water with a grease-loosening cleaner, then rinse off thoroughly with hot water. Repeat the process if necessary. Refit the grease filters when they are dry.

Dishwasher

Place grease filters in the dishwasher. Select most powerful washing programme and highest temperature, at least 65°C. Repeat the process. Refit the grease filters when they are dry.

When washing the metal grease filter in the dishwasher a slight discolouration of the filter can occur, this does not have any impact on its performance.

•Clean the inner housing using a hand hot solution only(never use caustic detergents, abrasive powders or brushes).

12 electrolux maintenance and care

Charcoal filter

• The charcoal filter should only be GB used if you want to use the hood in

recirculation mode.

•To do this you will need an original charcoal filter (available from your local Service Force Centre).

Cleaning/replacing the charcoal filter

The saturation of the activated charcoal occurs after more or less prolonged use, depending on the type of cooking and the regularity of cleaning of the grease filter.

In any case it is necessary to replace the cartridge at least every four

mounths.

The carbon filter may NOT be washed or regenerated.

•Fitting

Position the carbon filter inside the hood to cover the protection grill of the motor.

Fix the filter with 2 lateral knobs.

•To remove proceed in the reverse order.

•Always specify the hood model code number and serial number when ordering replacement filters. This information is shown on the rating plate located on the inside of the unit.

•The charcoal filter can be ordered from your local Service Force Centre.

electrolux maintenance and care 13

Warning

•Failure to observe the instructions on cleaning the unit and changing the filters will cause a fire hazard. You are therefore strongly recommended to follow these instructions.

•The manufacturer declines all responsibility for any damage to the motor or any fire damage linked to inappropriate maintenance or failure to observe the above safety recommendations.

Changing the light bulb(s)

• Disconnect the cooker hood from the mains supply.

•Prior to touching the light bulbs ensure they are cooled down.

•Replace the old bulb with a new one of the same type.

20W max

GU4 - 12 V - Ø 35mm - 30° Dichroic

• If the light does not come on, make sure the bulb has been inserted in correctly before contacting your local Service Force Centre.

14 electrolux maintenance and care

Cleaning the hood

•Clean the outside of the hood using a damp cloth and a solution of water and mild washing up liquid.

•Never use corrosive, abrasive or flammable cleaning products or products containing bleach.

•Never insert pointed objects in the motor’s protective grid.

•Only ever clean the switch panel and filter grill using a damp cloth and mild washing up liquid.

•Clean all the plastic parts with a soft cloth soaked in warm water and neutral soap.

•It is extremely important to clean the unit and change the filters at the recommended intervals. Failure to do so will cause grease deposits to build up that could constitute a fire hazard.

electrolux special accessories 15

Special accessories

Charcoal filter Type 15 Remote control RM 7000

Something Not Working

If your appliance fails to work properly please carry out the following checks.

Symptom	Solution

The cooker hood will not start...	Check that: The hood is connected
	to the electricity supply.
	Check that a fan speed has been
	selected.

The cooker hood is not working	Check that: The fan speed is set high
	enough for the task.
	The grease filters are clean.
	The kitchen is adequately vented to
	allow the entry of fresh air.
	If set up for recirculation, check that
	the charcoal filter is still effective.
	If set up for extraction, check that the
	ducting and outlets are not blocked.

The cooker hood has switched off	The safety cut-out device has been
during operation...	tripped. Turn off the hob and then wait
	for the device to reset. If the hood has
	been installed below the heights
	indicated in the installation instructions
	the motor will cut-out frequently which
	will damage the hood.

If after all these checks, the problem persists, contact your local Service Centre, quoting the model and serial number.

Please note that it will be necessary to provide proof of purchase for any inguarantee service calls.

In-guarantee customers should ensure that the above checks have been made as the engineer will make a charge if the fault is not a mechanical or electrical breakdown.

16 electrolux installation

Installation

Technical Details

	EFC 9671	EFC 6671
Dimensions (in cm):
Height (Extract. mode):	73-116	73-116
Height (Recirc. mode):	84,5-126	84,5-126
Width:	89,8	59,8
Depth:	45	45
Max. absorb. power:	310 W	290 W
Motor:	250 W	250 W
Lighting:	3x20 W	2 x 20 W
Length of the cable:	150 cm	150 cm
Electrical connection:	220-240 V	220-240 V
Fuse rating:	5A T	5AT

Mounting accessories included

1 deflector (with extensions)

2 screwdriver bits (for TORX screws)

1 fixing bracket for motor unit

1 support bracket for flues (3 pieces to assemble)

5 screws 5 x 45 mm

5 dowels Ø 8 mm

2 screws 2.9 x 6.5

8 screws 3.5 x 6.5

4 screws 4 x 8

1 reduction flange Ø 150-125-120 mm

Electrical connection

Safety warnings for the electrician

The mains power supply must correspond to the rating indicated on the plate situated inside the hood. If provided with a plug connect the hood to a socket in compliance with current regulations and positioned in an accessible area. If it not fitted with a plug (direct mains connection) or if the plug is not located in an accessible area apply a bi-polar switch in accordance with standards which assures the complete disconnection of the mains under conditions relating to over-current category III, in accordance with installation instructions. IMPORTANT: Before re-connecting the hood circuit to the mains supply and checking the efficient function, always check that the mains cable is correctly assembled.

electrolux installation 17

18 electrolux installation

First decide which functioning version is better for you

GB If you decide to use the hood in extraction mode we suggest that you position the upper section of the chimney so that the oulet slots are not visible once installation is completed, on the contrary you decide to use the hood in recirculation mode, BE SURE that the side with the slots is upright (see also A-B-C sequence).

Assembling the chimney flue support/bracket (3 parts)

The three parts should be fixed with 4 screws, the support extension is adjustable and should correspond to the internal width of the telescopic chimney flue.

Assembling the deflector (3 parts – only for filter version):

The three parts should be fixed with 2 screws, the deflector extension is adjustable and should correspond to the width of the chimney flue support, to which it is then fixed.

180°

C - OK!

4 x Ø 4x8

X =

	=	X
	=	=
		=
	F

6 x

Ø 3,5 x 6,5

G F

electrolux installation 19

Installation

Make sure that the cooker hood is disconnected from the power supply before carrying out the installation.

Remove the grease filters.

•Mark a central line on the wall to facilitate the installation procedure (1). Position the drilling template so that the median line printed on it corresponds to the central line marked previously, and so that the lower side of the template corresponds to the lower part of the cooker hood once it has been fitted (2).

•Make 3 holes with Ø 8 mm (2 on top and 1 underneath) and fit 3 rawl plugs into them (3).

•Fix the motor assembly support bracket in place using 2 screws (4).

•Make two holes with Ø 8 mm near the ceiling and use them to fix the support bracket of flue G in place (use the bracket as a template – rest it against the wall which joins onto the ceiling). Insert 2 rawl plugs into the holes (5) (install deflector F underneath the bracket using 4 screws if you wish to use the cooker hood as a filter version) and fix the bracket in place using 2 screws (6).

•Fit the cooker hood (7) and adjust its position (8-9).

•Fix the cooker hood in place (10).

•Install the exhaust tube (11) leading from cooker hood exhaust outlet B to the outside environment (ducted version) or deflector F (filter version).

•Perform all necessary electrical connections (12).