Cisco Systems PGW 2200 User Manual

Size:
4.77 Mb
Download

Cisco PGW 2200 Softswitch Release 9.8

Software Installation and Configuration

Guide

November 2008

Americas Headquarters

Cisco Systems, Inc. 170 West Tasman Drive

San Jose, CA 95134-1706USAhttp://www.cisco.com Tel: 408526-4000

800 553-NETS(6387) Fax: 408527-0883

Text Part Number: OL-18083-01

THE SPECIFICATIONS AND INFORMATION REGARDING THE PRODUCTS IN THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE. ALL STATEMENTS, INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE ACCURATE BUT ARE PRESENTED WITHOUT WARRANTY OF ANY KIND, EXPRESS OR IMPLIED. USERS MUST TAKE FULL RESPONSIBILITY FOR THEIR APPLICATION OF ANY PRODUCTS.

THE SOFTWARE LICENSE AND LIMITED WARRANTY FOR THE ACCOMPANYING PRODUCT ARE SET FORTH IN THE INFORMATION PACKET THAT SHIPPED WITH THE PRODUCT AND ARE INCORPORATED HEREIN BY THIS REFERENCE. IF YOU ARE UNABLE TO LOCATE THE SOFTWARE LICENSE OR LIMITED WARRANTY, CONTACT YOUR CISCO REPRESENTATIVE FOR A COPY.

The Cisco implementation of TCP header compression is an adaptation of a program developed by the University of California, Berkeley (UCB) as part of UCB’s public domain version of the UNIX operating system. All rights reserved. Copyright © 1981, Regents of the University of California.

NOTWITHSTANDING ANY OTHER WARRANTY HEREIN, ALL DOCUMENT FILES AND SOFTWARE OF THESE SUPPLIERS ARE PROVIDED “AS IS” WITH ALL FAULTS. CISCO AND THE ABOVE-NAMEDSUPPLIERS DISCLAIM ALL WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, WITHOUT LIMITATION, THOSE OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND NONINFRINGEMENT OR ARISING FROM A COURSE OF DEALING, USAGE, OR TRADE PRACTICE.

IN NO EVENT SHALL CISCO OR ITS SUPPLIERS BE LIABLE FOR ANY INDIRECT, SPECIAL, CONSEQUENTIAL, OR INCIDENTAL DAMAGES, INCLUDING, WITHOUT LIMITATION, LOST PROFITS OR LOSS OR DAMAGE TO DATA ARISING OUT OF THE USE OR INABILITY TO USE THIS MANUAL, EVEN IF CISCO OR ITS SUPPLIERS HAVE BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

CCDE, CCENT, Cisco Eos, Cisco HealthPresence, the Cisco logo, Cisco Lumin, Cisco Nexus, Cisco StadiumVision, Cisco TelePresence, Cisco WebEx, DCE, and Welcome to the Human Network are trademarks; Changing the Way We Work, Live, Play, and Learn and Cisco Store are service marks; and Access Registrar, Aironet, AsyncOS, Bringing the Meeting To You, Catalyst, CCDA, CCDP, CCIE, CCIP, CCNA, CCNP, CCSP, CCVP, Cisco, the Cisco Certified Internetwork Expert logo, Cisco IOS, Cisco Press, Cisco Systems, Cisco Systems Capital, the Cisco Systems logo, Cisco Unity, Collaboration Without Limitation, EtherFast, EtherSwitch, Event Center, Fast Step, Follow Me Browsing, FormShare, GigaDrive, HomeLink, Internet Quotient, IOS, iPhone, iQuick Study, IronPort, the IronPort logo, LightStream, Linksys, MediaTone, MeetingPlace, MeetingPlace Chime Sound, MGX, Networkers, Networking Academy, Network Registrar, PCNow, PIX, PowerPanels, ProConnect, ScriptShare, SenderBase, SMARTnet, Spectrum Expert, StackWise, The Fastest Way to Increase Your Internet Quotient, TransPath, WebEx, and the WebEx logo are registered trademarks of Cisco Systems, Inc. and/or its affiliates in the United States and certain other countries.

All other trademarks mentioned in this document or website are the property of their respective owners. The use of the word partner does not imply a partnership relationship between Cisco and any other company. (0812R)

Any Internet Protocol (IP) addresses used in this document are not intended to be actual addresses. Any examples, command display output, and figures included in the document are shown for illustrative purposes only. Any use of actual IP addresses in illustrative content is unintentional and coincidental.

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

© <year> Cisco Systems, Inc. All rights reserved.

Customer Order Number:

 

 

 

 

 

 

 

C O N T E N T S

 

 

 

 

 

Preface ix

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Document Objectives

ix

 

 

 

 

 

 

 

 

 

 

 

 

Audience

ix

 

 

 

 

 

 

 

 

 

 

 

 

 

Related Documentation

ix

 

 

 

 

 

 

 

 

 

 

 

Obtaining Documentation and Submitting a Service Request x

 

 

 

 

 

 

 

Document Change History

x

 

 

 

 

 

 

 

 

 

 

 

Preparing for Sun Solaris Operating System and Cisco PGW 2200 Softswitch Software

 

Installation

1-1

 

 

 

 

 

 

 

 

 

 

 

 

 

Supported Platforms and Cisco Products 1-1

 

 

 

 

 

 

 

 

 

Solaris 10, Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Software Release

 

Preinstallation Checklists

1-1

 

 

 

 

 

 

 

 

 

 

 

Required Software Media

1-2

 

 

 

 

 

 

 

 

 

 

Minimum System Requirements

1-2

 

 

 

 

 

 

 

 

 

Required Site-Specific Information

1-3

 

 

 

 

 

 

 

 

 

Required Machine-Specific Information 1-3

 

 

 

 

 

 

 

 

Required Tasks

1-3

 

 

 

 

 

 

 

 

 

 

 

 

Installing the Sun Solaris 10 Operating System

 

2-1

 

 

 

 

 

 

 

Supported Platforms

2-1

 

 

 

 

 

 

 

 

 

 

 

 

Supported Disk Drives

2-1

 

 

 

 

 

 

 

 

 

 

 

Before You Start 2-2

 

 

 

 

 

 

 

 

 

 

 

 

 

Cautions, Notes, and Tips

2-2

 

 

 

 

 

 

 

 

 

 

Loading the Sun Solaris 10 Operating System

2-2

 

 

 

 

 

 

 

Devices on Supported Platforms

2-3

 

 

 

 

 

 

 

 

 

Installing the Sun Solaris 10 Operating System for Sparc-based Platforms

2-3

 

 

 

 

 

Installing the Sun Solaris 10 Operating System for Opteron-based Platforms

2-13

 

 

 

 

Configuring Your Host

2-50

 

 

 

 

 

 

 

 

 

 

Platform-Specific Installation Procedures

2-62

 

 

 

 

 

 

 

Loading the Sun Solaris 10 Operating Environment

2-72

 

 

 

 

 

 

 

Installing the Sparc-based Solaris 10 Patches Package (CSCOh022)

2-73

 

 

 

 

 

 

Installing the Opteron-based Solaris 10 Patches Package (CSCOh032)

2-75

 

 

 

 

 

 

Installing the Solstice DiskSuite (CSCOh023)

2-77

 

 

 

 

 

 

 

Rebooting from the Mirrored (Secondary) Disk on Sparc-based Platforms

2-85

 

 

 

 

Rebooting from the Mirrored (Secondary) Disk on Opteron-based Platforms

2-87

 

 

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

 

OL-18083-01

 

 

 

 

 

 

 

 

 

 

 

iii

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Contents

 

 

 

Removing the Solstice DiskSuite

2-88

 

 

 

 

 

 

 

 

 

 

 

Installing the Log and Spool File Systems (CSCOh024)

2-89

 

 

 

 

 

 

 

 

Uninstalling the Log and Spool File System

2-97

 

 

 

 

 

 

 

 

 

Installing Cisco BAMS Archive Partition (CSCOh027)

2-98

 

 

 

 

 

 

 

 

Installing the Sparc-based Communications and Alarm Software Package (CSCOh026)

2-103

 

 

 

 

Installing the Opteron-based Communications Software Package (CSCOh036)

2-118

 

 

 

 

 

Installing the Verification Test Suite Script Package (CSCOh021)

2-129

 

 

 

 

 

 

 

Using the SunVTS Test Package

2-131

 

 

 

 

 

 

 

 

 

 

 

Normal Unit Test 2-131

 

 

 

 

 

 

 

 

 

 

 

 

 

Running a Test in Brief Mode

2-135

 

 

 

 

 

 

 

 

 

 

 

Running a Test in Full Mode

2-136

 

 

 

 

 

 

 

 

 

 

 

vts_script Execution Times

2-136

 

 

 

 

 

 

 

 

 

 

 

 

Removing the VTS Package (CSCOh021) 2-137

 

 

 

 

 

 

 

 

 

 

Configuring Lights-Out Management (LOM) or the Integrated Lights Out Manager (ILOM)

2-138

 

 

 

 

Configuring LOM on Sun Fire V40z Platform

2-138

 

 

 

 

 

 

 

 

 

Configuring ILOM on Sun Fire X4600 Platform

 

2-141

 

 

 

 

 

 

 

 

Configuring ILOM on Sun Netra X4200 M2 Platform

2-143

 

 

 

 

 

 

 

 

Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher

3-1

 

 

 

 

 

 

Before You Start

3-1

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cautions, Notes, and Tips

3-2

 

 

 

 

 

 

 

 

 

 

 

 

 

Installing the Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Releases

3-3

 

 

 

 

 

Installing Cisco PGW 2200 Softswitch Software on a Simplex System 3-3

 

 

 

 

 

 

 

Installing the Cisco Security Package (CSCOh020)

 

3-12

 

 

 

 

 

 

 

 

 

Enabling Sudo

3-15

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Installing the License File

3-15

 

 

 

 

 

 

 

 

 

 

 

 

 

Installing the License File if the Cisco PGW 2200 Softswitch is NOT Running

3-16

 

 

 

 

 

Installing the License File if the Cisco PGW 2200 Softswitch is Running

3-16

 

 

 

 

 

 

Installing on a Fault Tolerant System

3-17

 

 

 

 

 

 

 

 

 

 

 

Configuring the Cisco PGW 2200 Softswitch Software

4-1

 

 

 

 

 

 

 

 

Quick Guide to Configuring the Cisco PGW 2200 Softswitch Software

4-1

 

 

 

 

 

 

 

Before You Start

4-2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Software Directory Structure 4-3

 

 

 

 

 

 

 

 

 

 

 

 

Initial Cisco PGW 2200 Softswitch Software Configuration

4-4

 

 

 

 

 

 

 

 

Parameters Required for Initial Setup

4-7

 

 

 

 

 

 

 

 

 

 

 

Using the Cisco MGC Environment Configuration Tool

4-8

 

 

 

 

 

 

 

 

Configuring Groups and Users

4-11

 

 

 

 

 

 

 

 

 

 

 

 

 

Verifying the mgcgrp Group

4-11

 

 

 

 

 

 

 

 

 

 

 

 

 

Adding a User with Full MML Privileges 4-11

 

 

 

 

 

 

 

 

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

iv

 

 

 

 

 

 

 

 

 

 

 

OL-18083-01

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Contents

Adding a User with Minimal MML Privileges 4-12

 

Configuring SNMP Support Resources

4-13

 

 

 

Migrating the SNMP Configuration to a More Secure Environment (for Cisco PGW 2200 Softswitch

Release 9.3(2) or Later)

4-14

 

 

 

 

 

 

Basic Tasks

4-14

 

 

 

 

 

 

 

Before You Run the config-snmp Utility

4-14

 

Running the config-snmp Utility

4-15

 

 

 

Adding an SNMP Community Entry 4-17

 

 

Deleting an SNMP COMMUNITY

4-19

 

 

Adding a Trap Destination

 

4-20

 

 

 

 

Deleting a Trap Destination

4-22

 

 

 

Activating the New Settings

4-23

 

 

 

Verifying the SNMP Configuration Migration

4-24

 

Configuring the Execution Environment 4-25

 

 

 

Changing XECfgParm.dat File Parameters

4-26

 

 

Changing XECfgParm.dat File Parameters in a Running Fault Tolerant System 4-27

Configuring Basic System Information

4-28

 

 

Specifying IP Addresses

4-30

 

 

 

 

 

Configuring Engine Parameters

4-32

 

 

 

 

Setting the Call Cutoff Timer

4-34

 

 

 

 

Enabling Call Screening

4-34

 

 

 

 

 

 

Configuring Call Detail Record File Output

4-35

 

 

Configuring the Clearing Location and Default Location Parameters

4-36

Configuring Switchover

4-39

 

 

 

 

 

 

Initializing the Provisioning Object Manager

4-41

 

Configuring SCP Queries 4-42

 

 

 

 

 

 

Before You Start

4-43

 

 

 

 

 

 

 

Modifying trigger.dat file parameters with provisioning commands

4-43

Configuring the trigger.dat File Attributes

4-43

 

 

Configuring the Translation Type Attribute

4-44

 

Sample trigger.dat File

4-45

 

 

 

 

 

 

Initializing the Call Screening Database

4-82

 

 

 

.odbc.ini File Information

4-83

 

 

 

 

 

Setting Up Replication

4-83

 

 

 

 

 

 

Network Requirements

4-84

 

 

 

 

Initializing Database Replication

4-85

 

 

 

Verifying Database Replication

4-86

 

 

 

 

 

Troubleshooting the Main Memory Database Replication 4-87

 

 

 

 

 

Displaying the Main Memory Database Replication Status

4-87

 

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

OL-18083-01

 

 

v

 

 

 

 

 

Contents

 

 

 

Verifying Database Synchronization 4-87

 

 

 

 

 

 

 

 

 

Synchronizing Databases

4-88

 

 

 

 

 

 

 

 

 

Checking for Installation Errors 4-88

 

 

 

 

 

 

 

 

 

Reinstalling CSCOga002

4-89

 

 

 

 

 

 

 

 

 

Configuring Cisco ITP-Ls

4-89

 

 

 

 

 

 

 

 

 

 

 

Configuring Disk Monitor During Initial Software Configuration 4-89

 

 

 

 

 

 

 

 

Configuring the Data Dumper

4-90

 

 

 

 

 

 

 

 

 

 

Configuring the Data Dumper to Support Cisco BAMS

4-92

 

 

 

 

 

 

 

 

Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8

5-1

 

 

 

 

Conditions for Migration

5-1

 

 

 

 

 

 

 

 

 

 

 

Cautions and Notes

5-2

 

 

 

 

 

 

 

 

 

 

 

Required Software

5-3

 

 

 

 

 

 

 

 

 

 

 

 

License Installation

5-3

 

 

 

 

 

 

 

 

 

 

 

Recording System Data

5-3

 

 

 

 

 

 

 

 

 

 

 

Migration Overview

5-4

 

 

 

 

 

 

 

 

 

 

 

Migration from Release 9.5 or 9.6 to Release 9.8 without Platform Changes

 

5-5

 

 

 

 

 

Migrating the Second Cisco PGW 2200 Softswitch Software to Release 9.8

5-5

 

 

 

 

Backing Up the Cisco PGW 2200 Softswitch Configuration Files

5-5

 

 

 

 

 

Installing Sun Solaris 10

5-8

 

 

 

 

 

 

 

 

 

Loading the Sun Solaris 10 Operating Environment Packages

5-8

 

 

 

 

 

 

 

Restoring Data Files

5-9

 

 

 

 

 

 

 

 

 

 

Installing and Verifying the Cisco PGW 2200 Softswitch Software

 

5-9

 

 

 

 

 

Migrating the First Cisco PGW 2200 Softswitch Software to Release 9.8

5-10

 

 

 

 

Backing Up the Cisco PGW 2200 Softswitch Configuration Files

5-11

 

 

 

 

 

Installing Sun Solaris 10

5-13

 

 

 

 

 

 

 

 

 

Loading the Sun Solaris 10 Operating Environment Packages

5-14

 

 

 

 

 

 

Restoring Data Files

5-14

 

 

 

 

 

 

 

 

 

 

Installing and Verifying the Cisco PGW 2200 Softswitch Software

 

5-15

 

 

 

 

 

Transferring Additional Configuration Files

5-16

 

 

 

 

 

 

 

 

Migration from Release 9.7 to Release 9.8 without Platform Changes

5-20

 

 

 

 

 

 

Upgrading Lively from Sparc-based Platforms to Opteron-based Platforms

5-21

 

 

 

 

 

Before You Start

5-21

 

 

 

 

 

 

 

 

 

 

 

Live Upgrade Procedure

5-22

 

 

 

 

 

 

 

 

 

 

Falling Back Overview

5-26

 

 

 

 

 

 

 

 

 

 

 

Falling Back to the Cisco PGW 2200 Softswitch Software Release 9.7 without Platform Changes 5-26

 

 

 

Falling Back to Solaris 8 and Cisco PGW 2200 Softswitch Release 9.5 or 9.6

5-27

 

 

 

 

Falling Back to Solaris 8 If Hard Drives Were Replaced During the Upgrade

5-27

 

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

vi

 

 

 

 

 

 

 

 

 

 

OL-18083-01

 

 

 

 

 

 

 

 

 

 

 

 

 

Contents

 

Falling Back to Solaris 8 on the Second Disk Drive

5-28

 

 

 

 

 

 

 

Restoring the Original Cisco PGW 2200 Softswitch Software

5-32

 

 

 

 

 

 

Falling Back to Previous Cisco PGW 2200 Softswitch Software Releases with Platform Changes 5-32

 

Replacing Hard Disks on an Existing Solaris 10 Platform 5-33

 

 

 

 

 

 

 

Backup Procedure

5-34

 

 

 

 

 

 

 

 

 

 

 

Hard Disk Replacement Procedure 5-34

 

 

 

 

 

 

 

 

 

Loading the Solaris 10 Operating System

5-35

 

 

 

 

 

 

 

 

Loading the Sun Solaris 10 Operating Environment Packages

5-35

 

 

 

 

 

 

Installing the Cisco PGW 2200 Softswitch

5-35

 

 

 

 

 

 

 

 

Restoring the System

5-35

 

 

 

 

 

 

 

 

 

 

Configuring the Local Area Network Switch

6-1

 

 

 

 

 

 

 

 

LAN Switch Overview

6-1

 

 

 

 

 

 

 

 

 

 

 

Catalyst 2900 XL Series

 

6-2

 

 

 

 

 

 

 

 

 

 

 

Catalyst 5500 and 5000 Series

6-2

 

 

 

 

 

 

 

 

 

 

XECfgParm.dat File Parameters

A-1

 

 

 

 

 

 

 

 

 

 

Understanding the XECfgParm.dat File Format

A-1

 

 

 

 

 

 

 

 

Cisco PGW 2200 Softswitch XECfgParm.dat Files

A-1

 

 

 

 

 

 

 

Facility Names

 

A-1

 

 

 

 

 

 

 

 

 

 

 

Special Parameters

A-2

 

 

 

 

 

 

 

 

 

 

Cisco PGW 2200 Softswitch 9.x XECfgParm.dat File Parameter Definitions

A-2

 

 

 

 

 

Client/Server and Secure Connectivity Relationships

B-1

 

 

 

 

 

 

 

Client/Server and Secure Connectivity Relationships

B-1

 

 

 

 

 

 

 

Secure Connectivity Among Cisco PGW 2200 Softswitch Applications

B-1

 

 

 

 

 

Secure Connectivity Between Cisco PGW 2200 Softswitch Application Platforms

B-2

 

Secure Connectivity Between Cisco BAMS Application Platforms B-2

 

 

 

 

 

 

Secure Connectivity Between Cisco BAMS and Cisco PGW 2200 Softswitch Application

 

Platforms B-3

 

 

 

 

 

 

 

 

 

 

 

 

 

HP OpenView Sample SNMP Configuration

C-1

 

 

 

 

 

 

 

 

Configuring the Cisco PGW 2200 Softswitch to Send Alarms to HP OpenView

C-1

 

 

 

 

 

Formatting Trap Messages

C-3

 

 

 

 

 

 

 

 

 

 

Sample Installation Scripts

D-1

 

 

 

 

 

 

 

 

 

 

Sample Output from install.sh

D-1

 

 

 

 

 

 

 

 

 

 

Updated Configuration File Sample

D-11

 

 

 

 

 

 

 

 

 

Sample Configured snmpd.cnf File

D-13

 

 

 

 

 

 

 

 

 

Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.8(1)

D-16

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

OL-18083-01

 

 

 

 

 

 

 

 

 

 

vii

 

 

 

 

 

 

 

 

 

 

 

 

 

Contents

Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.7(3)

D-27

Sample Configured XECfgParm.dat Files for Cisco PGW 2200 Softswitch Release 9.6(1)

D-37

Sample Uninstall Scripts E-1

Removing a Cisco PGW 2200 Softswitch Software Version: Sample Output for uninstall.sh E-1

Sample LAN Configurations F-1

 

 

Sample Configuration for Cisco Catalyst 5500 A

F-1

 

Sample Configuration for Cisco Catalyst 5500 A RSM

F-7

Sample Configuration for Cisco Catalyst 5500 B

F-8

 

Sample Configuration for Cisco Catalyst 5500 B RSM

F-15

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

viii

OL-18083-01

 

 

 

Preface

This preface describes the objectives of this document and explains how to find additional information on related products and services. It contains the following sections:

Document Objectives, page ix

Audience, page ix

Related Documentation, page ix

Obtaining Documentation and Submitting a Service Request, page x

Document Change History, page x

Document Objectives

This guide describes the steps necessary to install and configure the Sun Solaris 10 operating system, and the Cisco PGW 2200 Softswitch software Release 9.8.

Note This guide does not cover media gateway (MGW) or Cisco PGW 2200 Softswitch hardware installation. For instructions on installing these components, see theCisco PGW 2200 Softswitch Hardware Installation Guide.

Audience

The audience for this document is network operators and administrators. This audience is assumed to have experience in telecommunications networks, protocols, and equipment, and a familiarity with data communications networks, protocols, and equipment.

Related Documentation

This document contains information that is related to Cisco PGW 2200 Softswitch software installation and configuration. For additional information on those subjects, see the documents at this URL:

http://www.cisco.com/en/US/products/hw/vcallcon/ps2027/tsd_products_support_series_home.html

You can also find the Cisco PGW 2200 Softswitch Documentation Mapat the following URL:

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

OL-18083-01

ix

 

Preface

http://www.cisco.com/en/US/products/hw/vcallcon/ps2027/products_documentation_roadmaps_list.ht ml

Other useful reference publications include

Overviews of the related telephony solutions—Describethe Cisco telephony solutions with which the Cisco PGW 2200 Softswitch node is associated

Provisioning guides for the related telephony solutions—Describethe provisioning steps for the Cisco telephony solutions with which the Cisco PGW 2200 Softswitch node is associated

Solution gateway installation and configuration guides—Describethe steps for installing and configuring the media gateway for a particular Cisco telephony solution

Cisco IP Transfer Point - LinkExtender—Describesthe Cisco IP Transfer Point - LinkExtender (CiscoIPT-L,formerly known as the Cisco Signaling Link Terminal or Cisco SLT) and provides configuration information

Obtaining Documentation and Submitting a Service Request

For information on obtaining documentation, submitting a service request, and gathering additional information, see the monthly What’s New in Cisco Product Documentation, which also lists all new and revised Cisco technical documentation at

http://www.cisco.com/en/US/docs/general/whatsnew/whatsnew.html

Subscribe to the What’s New in Cisco Product Documentation as a Really Simple Syndication (RSS) feed and set content to be delivered directly to your desktop using a reader application. The RSS feeds are a free service and Cisco currently supports RSS version 2.0.

Document Change History

Release Number

Document Number

Change Date

Change Summary

 

 

 

 

9.8(1)

OL-18083-01

November 2008

Initial release

 

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

x

OL-18083-01

 

 

 

C H A P T E R 1

Preparing for Sun Solaris Operating System and Cisco PGW 2200 Softswitch Software Installation

This chapter provides checklists describing the required and optional components, software media, and information you must have on hand before installing the Sun Solaris operating system and the

Cisco PGW 2200 Softswitch software:

Cisco PGW 2200 Softswitch Release 9.8 and up, which requires the Sun Solaris Operating System 10

Note The entire installation procedure takes approximately 2 hours to complete.

Supported Platforms and Cisco Products

The following Cisco products are supported by this software:

Cisco PGW 2200 Softswitch

Cisco Billing and Measurements Server (BAMS)

Cisco H.323 Signaling Interface (HSI)

The platforms that are supported for these products are identified in the Cisco PGW 2200 Softswitch Hardware Installation Guide (Release 7 & 9).

Solaris 10, Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Software Release Preinstallation Checklists

Table 1-1 throughTable 1-4 list the required and optional tasks, information, and software media for installing the Solaris 10 operating system and the Cisco PGW 2200 Softswitch software Release 9.8 and higher.

Before installing the Sun Solaris operating system, Solaris patches, and alarm card software, ensure that you collect the information and complete tasks listed in the following tables.

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

OL-18083-01

1-1

 

 

 

Chapter 1 Preparing for Sun Solaris Operating System and Cisco PGW 2200 Softswitch Software Installation

Solaris 10, Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Software Release Preinstallation Checklists

Note The target machine must have a terminal connected to the console port by means of a serial cable.

Required Software Media

Gather all of the appropriate software media listed in Table 1-1.For more information, see the appropriate Sun documentation that shipped with your system.

Table 1-1Solaris 10 Required Media Checklist

Media

Version

The following CD-ROMdisks are ordered from Cisco:

Cisco Solaris 10 Operating System Jumpstart Disk

This disk installs the Sun Solaris 10 Operating System, configured specifically to support the

Cisco PGW 2200 Softswitch software. There are two versions of this disk, one for each of the supported platform types:

Cisco Solaris 10 Operating System Jumpstart Disk for

06/06

Sparc-basedplatforms

 

Cisco Solaris 10 Operating System Jumpstart Disk for

01/06

Opteron-basedplatforms

 

Cisco Solaris 10 Operating Environment CD

3.0(6)

This disk contains the following packages:

 

CSCOh020 (MGC Security package)

CSCOh021 (Verification Test Suite scripts)

CSCOh022 (Solaris 10 patches for Sparc-basedplatforms)

CSCOh023 (DiskSuite installation scripts)

CSCOh024 (Log/Spool installation for Sparc-basedplatforms)

CSCOh026 (Xterm, ftp, ntp, and alarm software installation for Sparc-basedplatforms)

CSCOh032 (Solaris 10 patches for Opteron-basedplatforms)

CSCOh036 (Xterm, ftp, and ntp installation for Opteron-basedplatforms)

Minimum System Requirements

Refer to the Cisco PGW 2200 Softswitch Hardware Installation Guide (Release 7 & 9) for the host minimum hardware requirements. Before using the minimum hardware configuration, consult your Cisco representative to determine the hardware that gives you the best performance results based on your network configuration, proposed traffic, and desired processing power.

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

1-2

OL-18083-01

 

 

Chapter 1 Preparing for Sun Solaris Operating System and Cisco PGW 2200 Softswitch Software Installation

Solaris 10, Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Software Release Preinstallation

Required Site-SpecificInformation

Your system site administrator can provide the required site-specificinformation inTable 1-2.Use the Notes column in this table to record the information. Several steps in the installation procedure inChapter 2, “Installing the Sun Solaris 10 Operating System” require you to provide this information.

Table 1-2Site-SpecificInformation

Required Information

Notes

Subnet Mask

(Example: 255.255.255.0)

Default router (Example: 111.11.xxx.1)

DNS server

NTP server IP address

Time zone

(Example: United States (Eastern))

Root password

(Assigned by your system site administrator)

Required Machine-SpecificInformation

Your system site administrator can provide the information called for in Table 1-3 as it applies to your target Sun Netra machine. Use the Notes column in this table to record the information. Several steps in the installation procedure require you to provide this information.

Table 1-3Machine-SpecificChecklist

Information

Notes

Host name of target machine

IP address of target machine

Default router IP address

Additional Ethernet IP address

Subnet address for each additional Ethernet IP address

Netmask address for each additional Ethernet IP address

Required Tasks

Before you begin installing the Solaris 10 operating system, perform the tasks listed in Table 1-4.

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

OL-18083-01

1-3

 

 

 

Chapter 1 Preparing for Sun Solaris Operating System and Cisco PGW 2200 Softswitch Software Installation

Solaris 10, Cisco PGW 2200 Softswitch Software Release 9.8 and Higher Software Release Preinstallation Checklists

Table 1-4

Tasks Checklist

Check Tasks

Make sure that the target machine is connected to a terminal by a serial cable inserted into the console port.

Have your company's internal support and Cisco support contact information readily available so you can get help with the installation if needed. If you have questions or need assistance, see the “Obtaining Documentation and Submitting a Service Request” section on page x.

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

1-4

OL-18083-01

 

 

C H A P T E R 2

Installing the Sun Solaris 10 Operating System

This chapter provides instructions for installing the packages that create the Sun Solaris 10 operating system and its operating environment on the Sun Netra and Sun Fire platforms. The following sections contain these instructions.

Note In the following procedures, your responses to prompts sometimes depend on the disk drive size or other particulars of your system. These are pointed out as you follow the procedures.

Supported Platforms, page 2-1

Supported Disk Drives, page 2-1

Before You Start, page 2-2

Loading the Sun Solaris 10 Operating System, page 2-2

Loading the Sun Solaris 10 Operating Environment, page 2-72

Note For procedures on migrating to Solaris 10 and Cisco PGW 2200 Softswitch software Release 9.8, seeChapter 5, “Migrating to Solaris 10 and Cisco PGW 2200 Softswitch Software Release 9.8.”

Supported Platforms

This document describes the specific steps necessary for installing the Sun Solaris 10 operating system and the operating environment on the Sun Netra and Sun Fire platforms. Two platform types are used: Sparc-basedandOpteron-based.The platforms that are supported for these products are identified in the

Cisco PGW 2200 Softswitch Hardware Installation Guide (Release 7 & 9).

Supported Disk Drives

The following disk drives are supported:

73 GB

146 GB

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

OL-18083-01

2-1

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Before You Start

Before You Start

Be sure to read the following cautions, notes, and tips before installing the Sun Solaris 10 operating system and the operating environment.

Cautions, Notes, and Tips

Note

Note

Note

Note

Note

Tip

The procedures in this chapter require a working knowledge of the system administration procedures for the Sun Solaris (UNIX) operating system.

Be sure to have the required information listed in Chapter 1, “Preparing for Sun Solaris Operating System and Cisco PGW 2200 Softswitch Software Installation,” before you begin the installation process.

Allow at least 2 hours downtime for the installation of the Cisco PGW 2200 Softswitch software environment.

The text in the screens displayed throughout this document might differ slightly from the text displayed on your console. The screen displays are for reference only and should be treated as examples.

Most of the steps in the installation process ask you to press F2 to continue. However,F2 does not apply to all console types. If it does not apply on your system, you should pressEsc-2 instead.

During the installation process, monitor system output frequently for error messages and correct any error conditions before continuing with the installation.

Loading the Sun Solaris 10 Operating System

This section provides the following instructions for loading the Sun Solaris 10 operating system:

Devices on Supported Platforms, page 2-3

Installing the Sun Solaris 10 Operating System for Sparc-based Platforms, page 2-3

Installing the Sun Solaris 10 Operating System for Opteron-based Platforms, page 2-13

Configuring Your Host, page 2-50

Platform-Specific Installation Procedures, page 2-62

Installing the Sparc-based Solaris 10 Patches Package (CSCOh022), page 2-73

Installing the Opteron-based Solaris 10 Patches Package (CSCOh032), page 2-75

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-2

OL-18083-01

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Installing the Solstice DiskSuite (CSCOh023), page 2-77

Installing the Log and Spool File Systems (CSCOh024), page 2-89

Installing Cisco BAMS Archive Partition (CSCOh027), page 2-98

Installing the Sparc-based Communications and Alarm Software Package (CSCOh026), page 2-103

Installing the Opteron-based Communications Software Package (CSCOh036), page 2-118

Installing the Verification Test Suite Script Package (CSCOh021), page 2-129

Devices on Supported Platforms

Table 2-1 shows the Ethernet and disk drive device names for each platform type. This table is referenced throughout this chapter.

Table 2-1Device Names on Supported Host Platforms

 

Ethernet Interfaces

 

 

Disk Drives

 

 

 

Platform Type

 

 

 

 

 

 

 

 

First

Second

Third

Fourth

First

Second

Third

Fourth

 

 

 

 

 

 

 

 

 

Sun Fire V210 /

bge0

bge1

bge2

bge3

c1t0d0

c1t1d0

Netra 210

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Netra 240

bge0

bge1

bge21

bge31

c1t0d0

c1t1d0

Sun Fire V40z

bge0

bge1

ce0

 

c1t0d0

c1t1d0

 

 

 

 

 

 

 

 

 

Sun Fire X4600

e1000g0

e1000g1

e1000g2

e1000g3

c3t0d0

c3t1d0

 

 

 

 

 

 

 

 

 

Sun Fire X4600

e1000g0

e1000g1

e1000g2

e1000g3

c3t0d0

c3t1d0

M2

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Netra 440

ce0

ce1

c1t0d0

c1t1d0

c1t2d01

c1t3d01

Netra X4200 M2

nge0

nge1

e1000g0

e1000g1

c3t0d0

c3t1d0

 

 

 

 

 

 

 

 

 

1. This device is not used currently.

Note If your platform has multiple disk drives, install the Solaris 10 Operating System on the first disk drive only.

Installing the Sun Solaris 10 Operating System for Sparc-basedPlatforms

The instructions in this section were written to correspond with the instructions in the Cisco Solaris 10 Operating System Jumpstart Disk for Sparc-basedPlatforms. Other Solaris installations are similar, with slight variations. These instructions will note the differences between the sets of installation instructions.

Step 1 Choose one of the following options to connect the Cisco PGW 2200 Softswitch:

Connect to the Cisco PGW 2200 Softswitch through a console port.

Connect a keyboard and monitor to the Cisco PGW 2200 Softswitch.

Step 2 This step isoptional—ifyou decide to skip this step, go toStep 3.

a. Place the system insingle-usermode by shutting down the standby machine.

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

OL-18083-01

2-3

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

b.When the machine prompts for a password, type either ^ -d to proceed with normal startup, or the root password for system maintenance.

Step 3 Load the appropriate version of theCD-ROMlabeled Cisco Solaris 10 Operating System Jumpstart Disk forSparc-basedPlatforms into theCD-ROMdrive.

Step 4 If the system is currently running, log in asroot.

Step 5 Bring the system to theok prompt by entering the following command:

# init 0

Note If you are prompted to select a language before booting from the CD, go to theok prompt by sending a break on the console port. On SunSparc-basedplatforms, the key sequence<cr>#. gets you to the system controller prompt.

From the system controller prompt, use the break -y command to break out of the operating system andconsole -f command to return to the console display. You should see theok prompt.

Step 6 Boot the system from theCD-ROMdrive by entering the appropriate command:

ok boot cdrom - install

Information similar to the following is displayed:

ok boot cdrom - install

SC Alert: Host System has Reset

Probing system devices

Probing memory

Probing I/O buses

Sun Fire V210, No Keyboard

Copyright 2005 Sun Microsystems, Inc. All rights reserved.

OpenBoot 4.18.5,

2048 MB memory installed, Serial #52030991.

Ethernet address

0:3:ba:19:ee:f, Host ID: 8319ee0f.

Initializing

1MB of memory at addr

103feec000

Initializing

1MB of memory at addr

103fee0000

Initializing

1MB of memory at addr

103f002000

Initializing

1MB of memory at addr

103e002000

Initializing

1MB of memory at addr

1000000000

Initializing

1MB of memory at addr

0

Rebooting with command: boot cdrom - install

Boot device: /pci@1e,600000/ide@d/cdrom@0,0:f File and args: - install

 

 

 

SunOS Release 5.10 Version Generic_118833-1764-bit

 

 

 

Copyright 1983-2005Sun Microsystems, Inc. All rights reserved.

 

 

 

Use is subject to license terms.

 

 

 

Hardware watchdog enabled

 

 

 

Configuring devices.

 

 

 

Using RPC Bootparams for network configuration information.

 

 

 

Attempting to configure interface bge3...

 

 

 

Skipped interface bge3

 

 

 

Attempting to configure interface bge2...

 

 

 

Skipped interface bge2

 

 

 

Attempting to configure interface bge1...

 

 

 

Skipped interface bge1

 

 

 

Attempting to configure interface bge0...

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

2-4

 

OL-18083-01

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Skipped interface bge0

Beginning system identification...

Searching for configuration file(s)...

Search complete.

Discovering additional network configuration...

Completing system identification...

Starting remote procedure call (RPC) services: done.

System identification complete.

Starting Solaris installation program...

Searching for JumpStart directory...

<<< using cdrom install_config >>>

Checking rules.ok file...

Using profile: any_machine

Using finish script: any_finish

Executing JumpStart preinstall phase...

Searching for SolStart directory...

Checking rules.ok file...

Using begin script: install_begin

Using finish script: patch_finish

Executing SolStart preinstall phase...

Executing begin script "install_begin"...

Begin script install_begin execution completed.

Processing profile

-Selecting cluster (SUNWCrnet)

-Selecting package (SUNWadmc)

-Selecting package (SUNWadmfw)

-Selecting package (SUNWcpc)

-Selecting package (SUNWcpcu)

-Selecting package (SUNWcstl)

-Selecting package (SUNWless)

-Selecting package (SUNWlur)

-Selecting package (SUNWluu)

-Selecting package (SUNWmkcd)

-Selecting package (SUNWmipu)

-Selecting package (SUNWmipr)

-Selecting package (SUNWocf)

-Selecting package (SUNWocfr)

-Selecting package (SUNWspnego)

-Selecting package (SUNWter)

-Selecting package (SUNWtnfc)

-Selecting package (SUNWucbt)

-Selecting package (SUNWvld)

-Selecting package (SUNWvldu)

-Selecting package (SUNWzsh)

-Selecting package (SUNWsacom)

-Selecting package (SUNWroute)

-Selecting package (SUNWxwfnt)

-Selecting package (SUNWxwdv)

-Selecting package (SUNWctpls)

-Selecting package (SUNWgssdh)

-Selecting package (SUNWm64cf)

-Selecting package (SUNWj5rt)

-Selecting package (SUNWxwplt)

-Selecting package (SUNWxwplr)

-Selecting package (SUNWdtcor)

-Selecting package (SUNWxwice)

-Selecting package (SUNWxwrtl)

-Selecting package (SUNWlibC)

-Selecting package (SUNWmfrun)

-Selecting package (SUNWi15rf)

-Selecting package (SUNWmdu)

-Selecting package (SUNWadmfr)

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

OL-18083-01

2-5

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

-Selecting package (SUNWrsg)

-Selecting package (SUNWsadmi)

-Selecting package (SUNWsasnm)

-Selecting package (SUNWmibii)

-Selecting package (SUNWxi18n)

-Selecting package (SUNWtoo)

-Selecting package (SUNWsprot)

-Selecting package (SUNWbip)

-Selecting package (SUNWbind)

-Selecting package (SUNWbindr)

-Selecting package (SUNWgzip)

-Selecting package (SUNWzip)

-Selecting package (SUNWbash)

-Selecting package (SUNWtcsh)

-Selecting package (SUNWgss)

-Selecting package (SUNWgssc)

-Selecting package (SUNWgssk)

-Selecting package (SUNWqos)

-Selecting package (SUNWqosu)

-Selecting package (SUNWmdb)

-Selecting package (SUNWmdbr)

-Selecting package (SUNWmdbdm)

-Selecting package (SUNWnfsckr)

-Selecting package (SUNWnfscr)

-Selecting package (SUNWnfscu)

-Selecting package (SUNWifp)

-Selecting package (SUNWged)

-Selecting package (SUNW1394)

-Selecting package (SUNWqfed)

-Selecting package (SUNWaccr)

-Selecting package (SUNWaccu)

-Selecting package (SUNWus)

-Selecting package (SUNWrsgk)

-Selecting package (SUNWzebrar)

-Selecting package (SUNWzebrau)

-Selecting package (SUNWeurf)

-Selecting package (SUNWgcmn)

-Selecting package (SUNWeuodf)

-Selecting package (SUNWxwacx)

-Selecting package (SUNWpoolr)

-Selecting package (SUNWpool)

-Selecting package (SUNWluzone)

-Selecting package (SUNWzoner)

-Selecting package (SUNWzoneu)

-Selecting package (SUNWbtool)

-Selecting package (SUNWdtrc)

-Selecting package (SUNWdtrp)

-Selecting package (SUNWfss)

-Selecting package (SUNWinst)

-Selecting package (SUNWipc)

-Selecting package (SUNWqus)

-Selecting package (SUNWqusu)

-Selecting package (SUNWrcmdc)

-Selecting package (SUNWdtdmr)

-Selecting package (SUNWtltk)

-Selecting package (SUNWtnetc)

-Selecting package (SUNWtnfd)

-Selecting package (SUNWtnetd)

-Selecting package (SUNWtnetr)

-Selecting package (SUNWsshcu)

-Selecting package (SUNWsshdr)

-Selecting package (SUNWsshdu)

-Selecting package (SUNWsshr)

-Selecting package (SUNWsshu)

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-6

OL-18083-01

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

-Selecting package (SUNWpd)

-Selecting package (SUNWced)

-Selecting package (SUNWcart200)

-Selecting package (SUNWkvmt200)

-Selecting package (SUNWust1)

-Selecting package (SUNWatfsr)

-Selecting package (SUNWatfsu)

-Selecting package (SUNWrcmdr)

-Selecting package (SUNWrcmds)

-Selecting package (SUNWxcu4)

-Selecting package (SUNWefc)

-Selecting package (SUNWglmr)

-Selecting package (SUNWi2cr)

-Selecting package (SUNWpstl)

-Selecting package (SUNWbart)

-Selecting package (SUNWpiclu)

-Selecting package (SUNWpiclr)

-Selecting package (SUNWopensslr)

-Selecting package (SUNWopenssl-commands)

-Selecting all disks

-Configuring boot device

-Using disk (c1t0d0) for "rootdisk"

-Configuring / (c1t0d0s0)

-Configuring /var (c1t0d0s1)

-Configuring swap (c1t0d0s3)

-

Configuring

(c1t0d0s4)

-

Configuring

(c1t0d0s6)

-Configuring /opt (c1t0d0s5)

-Deselecting unmodified disk (c1t1d0)

Verifying disk configuration

- WARNING: Changing the system's default boot device in the EEPROM

Verifying space allocation

- Total software size: 376.86 Mbytes

Preparing system for Solaris install

Configuring disk (c1t0d0)

- Creating Solaris disk label (VTOC)

Creating and checking UFS file systems

-Creating / (c1t0d0s0)

-Creating /var (c1t0d0s1)

-Creating /opt (c1t0d0s5)

Beginning Solaris software installation

 

Starting software installation

 

 

 

 

 

 

 

SUNWcsu..........................

done.

363.07

Mbytes remaining.

 

SUNWcsr..........................

done.

359.22

Mbytes remaining.

 

SUNWcsl..........................

done.

347.35

Mbytes remaining.

 

SUNWcnetr........................

done.

347.23

Mbytes remaining.

 

SUNWckr..........................

done.

337.09

Mbytes remaining.

 

SUNWkvm.u........................

done.

335.16

Mbytes remaining.

 

SUNWcar.u........................

done.

334.65

Mbytes remaining.

 

SUNWcakr.u.......................

done.

315.55

Mbytes remaining.

 

SUNWxwice........................

done.

315.27

Mbytes remaining.

 

SUNWcsd..........................

done.

315.01

Mbytes remaining.

 

SUNWxwrtl........................

done.

314.87

Mbytes remaining.

 

SUNWzlib.........................

done.

314.62

Mbytes remaining.

 

SUNWbzip.........................

done.

314.36

Mbytes remaining.

 

SUNWlibmsr.......................

done.

311.13

Mbytes remaining.

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

 

 

2-7

 

 

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

 

 

Loading the Sun Solaris 10 Operating System

 

 

 

 

 

 

 

 

........................SUNWlibms

done.

311.09

Mbytes remaining.

 

 

 

 

SUNWxwfnt........................

done.

299.39

Mbytes remaining.

 

 

 

 

SUNWxwdv.........................

done.

299.34

Mbytes remaining.

 

 

 

 

SUNWxwplr........................

done.

299.28

Mbytes remaining.

 

 

 

 

SUNWperl584core..................

done.

293.83

Mbytes remaining.

 

 

 

 

SUNWperl584usr...................

done.

272.69

Mbytes remaining.

 

 

 

 

SUNWesu..........................

done.

270.73

Mbytes remaining.

 

 

 

 

SUNWcpp..........................

done.

270.63

Mbytes remaining.

 

 

 

 

SUNWdtcor........................

done.

270.60

Mbytes remaining.

 

 

 

 

SUNWxwplt........................

done.

249.87

Mbytes remaining.

 

 

 

 

SUNWlibC.........................

done.

244.13

Mbytes remaining.

 

 

 

 

SUNWctpls........................

done.

244.05

Mbytes remaining.

 

 

 

 

SUNWmfrun........................

done.

234.11

Mbytes remaining.

 

 

 

 

SUNWtcsh.........................

done.

233.72

Mbytes remaining.

 

 

 

 

SUNWtecla........................

done.

233.09

Mbytes remaining.

 

 

 

 

SUNWter..........................

done.

231.47

Mbytes remaining.

 

 

 

 

SUNWgcmn.........................

done.

231.44

Mbytes remaining.

 

 

 

 

SUNWpr...........................

done.

230.35

Mbytes remaining.

 

 

 

 

SUNWtls..........................

done.

222.76

Mbytes remaining.

 

 

 

 

SUNWdtdmr........................

done.

222.73

Mbytes remaining.

 

 

 

 

SUNWtltk.........................

done.

219.66

Mbytes remaining.

 

 

 

 

SUNWkrbr.........................

done.

219.58

Mbytes remaining.

 

 

 

 

SUNWkrbu.........................

done.

217.09

Mbytes remaining.

 

 

 

 

SUNWtnetc........................

done.

216.92

Mbytes remaining.

 

 

 

 

SUNWtnetd........................

done.

216.84

Mbytes remaining.

 

 

 

 

SUNWtnetr........................

done.

216.79

Mbytes remaining.

 

 

 

 

SUNWtnfc.........................

done.

216.29

Mbytes remaining.

 

 

 

 

SUNWtnfd.........................

done.

216.20

Mbytes remaining.

 

 

 

 

SUNWtoo..........................

done.

215.12

Mbytes remaining.

 

 

 

 

SUNWucbt.........................

done.

215.09

Mbytes remaining.

 

 

 

 

SUNWudaplr.......................

done.

215.06

Mbytes remaining.

 

 

 

 

SUNWudaplu.......................

done.

214.81

Mbytes remaining.

 

 

 

 

SUNWib...........................

done.

213.14

Mbytes remaining.

 

 

 

 

SUNWipoib........................

done.

213.00

Mbytes remaining.

 

 

 

 

SUNWtavor........................

done.

212.20

Mbytes remaining.

 

 

 

 

SUNWudapltu......................

done.

211.75

Mbytes remaining.

 

 

 

 

SUNWudapltr......................

done.

211.50

Mbytes remaining.

 

 

 

 

SUNWaudd.........................

done.

210.84

Mbytes remaining.

 

 

 

 

SUNWusb..........................

done.

209.47

Mbytes remaining.

 

 

 

 

SUNWusbs.........................

done.

209.39

Mbytes remaining.

 

 

 

 

SUNWuedg.........................

done.

209.21

Mbytes remaining.

 

 

 

 

SUNWugen.........................

done.

209.15

Mbytes remaining.

 

 

 

 

SUNWuksp.........................

done.

209.07

Mbytes remaining.

 

 

 

 

SUNWopenssl-libraries............

done.

202.10

Mbytes remaining.

 

 

 

 

SUNWwbsup........................

done.

201.74

Mbytes remaining.

 

 

 

 

SUNWinstall-patch-utils-root.....

done.

201.71

Mbytes remaining.

 

 

 

 

SUNWswmt.........................

done.

201.00

Mbytes remaining.

 

 

 

 

SUNWuprl.........................

done.

200.94

Mbytes remaining.

 

 

 

 

SUNWj5rt.........................

done.

118.41

Mbytes remaining.

 

 

 

 

SUNWocfr.........................

done.

118.34

Mbytes remaining.

 

 

 

 

SUNWocf..........................

done.

117.76

Mbytes remaining.

 

 

 

 

SUNWxi18n........................

done.

116.78

Mbytes remaining.

 

 

 

 

SUNWvld..........................

done.

116.73

Mbytes remaining.

 

 

 

 

SUNWvldu.........................

done.

116.68

Mbytes remaining.

 

 

 

 

SUNWnfscr........................

done.

116.53

Mbytes remaining.

 

 

 

 

SUNWnfsckr.......................

done.

115.12

Mbytes remaining.

 

 

 

 

SUNWnfscu........................

done.

114.83

Mbytes remaining.

 

 

 

 

SUNWgzip.........................

done.

114.73

Mbytes remaining.

 

 

 

 

SUNWgssc.........................

done.

114.68

Mbytes remaining.

 

 

 

 

SUNWgss..........................

done.

114.31

Mbytes remaining.

 

 

 

 

SUNWbip..........................

done.

114.12

Mbytes remaining.

 

 

 

 

SUNWrcmdc........................

done.

113.25

Mbytes remaining.

 

 

 

 

SUNWrcmds........................

done.

112.95

Mbytes remaining.

 

 

 

 

SUNWproduct-registry-root........

done.

112.93

Mbytes remaining.

 

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

2-8

 

 

 

 

OL-18083-01

 

 

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

 

 

 

 

Loading the Sun Solaris 10 Operating System

 

 

SUNWwsr2.........................

done.

112.59

Mbytes remaining.

 

SUNWlxml.........................

done.

109.19

Mbytes remaining.

 

SUNWlexpt........................

done.

108.61

Mbytes remaining.

 

SUNWxge..........................

done.

108.08

Mbytes remaining.

 

SUNWxcu4.........................

done.

106.87

Mbytes remaining.

 

SUNWxwacx........................

done.

106.69

Mbytes remaining.

 

SUNWsprot........................

done.

105.21

Mbytes remaining.

 

SUNWzfskr........................

done.

104.39

Mbytes remaining.

 

SUNWzfsr.........................

done.

103.43

Mbytes remaining.

 

SUNWsmapi........................

done.

102.80

Mbytes remaining.

 

SUNWzfsu.........................

done.

101.29

Mbytes remaining.

 

SUNWrsg..........................

done.

101.16

Mbytes remaining.

 

SUNWgssdh........................

done.

100.84

Mbytes remaining.

 

SUNWgssk.........................

done.

100.60

Mbytes remaining.

 

SUNWeurf.........................

done.

96.30

Mbytes remaining.

 

SUNWi15rf........................

done.

96.16

Mbytes remaining.

 

SUNWnisr.........................

done.

96.02

Mbytes remaining.

 

SUNWnisu.........................

done.

93.70

Mbytes remaining.

 

SUNWzebrar.......................

done.

93.63

Mbytes remaining.

 

SUNWzebrau.......................

done.

91.44

Mbytes remaining.

 

SUNWcpcu.........................

done.

90.90

Mbytes remaining.

 

SUNWfmdr.........................

done.

90.84

Mbytes remaining.

 

SUNWfmd..........................

done.

86.92

Mbytes remaining.

 

SUNWcslr.........................

done.

72.42

Mbytes remaining.

 

SUNWidnl.........................

done.

71.86

Mbytes remaining.

 

SUNWmdb..........................

done.

66.94

Mbytes remaining.

 

SUNWzip..........................

done.

66.75

Mbytes remaining.

 

SUNWmdbr.........................

done.

63.97

Mbytes remaining.

 

SUNWpiclu........................

done.

60.17

Mbytes remaining.

 

SUNWzoner........................

done.

60.11

Mbytes remaining.

 

SUNWmdr..........................

done.

57.74

Mbytes remaining.

 

SUNWmdu..........................

done.

57.04

Mbytes remaining.

 

SUNWadmc.........................

done.

55.16

Mbytes remaining.

 

SUNWadmfr........................

done.

55.14

Mbytes remaining.

 

SUNWadmfw........................

done.

54.43

Mbytes remaining.

 

SUNWadmlib-sysid.................

done.

54.17

Mbytes remaining.

 

SUNWadmr.........................

done.

54.09

Mbytes remaining.

 

SUNWadmap........................

done.

53.21

Mbytes remaining.

 

SUNWlur..........................

done.

51.67

Mbytes remaining.

 

SUNWluu..........................

done.

50.48

Mbytes remaining.

 

SUNWluzone.......................

done.

50.11

Mbytes remaining.

 

SUNWpoolr........................

done.

50.08

Mbytes remaining.

 

SUNWpool.........................

done.

49.24

Mbytes remaining.

 

SUNWzoneu........................

done.

48.61

Mbytes remaining.

 

SUNWluxop........................

done.

47.86

Mbytes remaining.

 

SUNWses..........................

done.

47.76

Mbytes remaining.

 

SUNWssad.........................

done.

47.45

Mbytes remaining.

 

SUNWifp..........................

done.

47.17

Mbytes remaining.

 

SUNWzsh..........................

done.

44.04

Mbytes remaining.

 

SUNW1394.........................

done.

43.27

Mbytes remaining.

 

SUNWinst.........................

done.

42.77

Mbytes remaining.

 

SUNWintgige......................

done.

42.51

Mbytes remaining.

 

SUNWipc..........................

done.

42.45

Mbytes remaining.

 

SUNWipfr.........................

done.

42.31

Mbytes remaining.

 

SUNWipfu.........................

done.

41.04

Mbytes remaining.

 

SUNWipged........................

done.

40.54

Mbytes remaining.

 

SUNWced.u........................

done.

39.90

Mbytes remaining.

 

SUNWcpc.u........................

done.

39.84

Mbytes remaining.

 

SUNWbash.........................

done.

39.11

Mbytes remaining.

 

SUNWaccr.........................

done.

39.01

Mbytes remaining.

 

SUNWaccu.........................

done.

38.64

Mbytes remaining.

 

SUNWefc.u........................

done.

38.36

Mbytes remaining.

 

SUNWiscsir.......................

done.

37.68

Mbytes remaining.

 

SUNWiscsiu.......................

done.

37.12

Mbytes remaining.

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

OL-18083-01

 

 

 

 

2-9

 

 

 

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

 

 

Loading the Sun Solaris 10 Operating System

 

 

 

 

 

 

 

 

.......................SUNWglmr.u

done.

37.04

Mbytes remaining.

 

 

 

 

SUNWi2cr.u.......................

done.

36.85

Mbytes remaining.

 

 

 

 

SUNWloc..........................

done.

36.34

Mbytes remaining.

 

 

 

 

SUNWpstl.u.......................

done.

36.21

Mbytes remaining.

 

 

 

 

SUNWus.u.........................

done.

36.16

Mbytes remaining.

 

 

 

 

SUNWbtool........................

done.

34.83

Mbytes remaining.

 

 

 

 

SUNWjfca.........................

done.

33.98

Mbytes remaining.

 

 

 

 

SUNWjfcau........................

done.

33.90

Mbytes remaining.

 

 

 

 

SUNWjss..........................

done.

29.54

Mbytes remaining.

 

 

 

 

SUNWkey..........................

done.

29.16

Mbytes remaining.

 

 

 

 

SUNWatfsr........................

done.

29.09

Mbytes remaining.

 

 

 

 

SUNWatfsu........................

done.

28.81

Mbytes remaining.

 

 

 

 

SUNWbart.........................

done.

28.76

Mbytes remaining.

 

 

 

 

SUNWbindr........................

done.

28.71

Mbytes remaining.

 

 

 

 

SUNWbind.........................

done.

25.60

Mbytes remaining.

 

 

 

 

SUNWless.........................

done.

25.44

Mbytes remaining.

 

 

 

 

SUNWcfcl.........................

done.

25.30

Mbytes remaining.

 

 

 

 

SUNWcfclr........................

done.

25.28

Mbytes remaining.

 

 

 

 

SUNWcfpl.........................

done.

24.92

Mbytes remaining.

 

 

 

 

SUNWcfplr........................

done.

24.87

Mbytes remaining.

 

 

 

 

SUNWlibsasl......................

done.

24.28

Mbytes remaining.

 

 

 

 

SUNWchxge........................

done.

24.04

Mbytes remaining.

 

 

 

 

SUNWlldap........................

done.

23.84

Mbytes remaining.

 

 

 

 

SUNWluxopr.......................

done.

23.17

Mbytes remaining.

 

 

 

 

SUNWm64cf........................

done.

23.11

Mbytes remaining.

 

 

 

 

SUNWcstl.........................

done.

22.96

Mbytes remaining.

 

 

 

 

SUNWmdbdm........................

done.

22.90

Mbytes remaining.

 

 

 

 

SUNWmibii........................

done.

22.78

Mbytes remaining.

 

 

 

 

SUNWsasnm........................

done.

21.91

Mbytes remaining.

 

 

 

 

SUNWsadmi........................

done.

20.91

Mbytes remaining.

 

 

 

 

SUNWsacom........................

done.

20.61

Mbytes remaining.

 

 

 

 

SUNWmipr.........................

done.

20.53

Mbytes remaining.

 

 

 

 

SUNWmipu.........................

done.

20.25

Mbytes remaining.

 

 

 

 

SUNWmkcd.........................

done.

18.95

Mbytes remaining.

 

 

 

 

SUNWdtrc.........................

done.

16.86

Mbytes remaining.

 

 

 

 

SUNWdtrp.........................

done.

16.41

Mbytes remaining.

 

 

 

 

SUNWfctl.........................

done.

15.97

Mbytes remaining.

 

 

 

 

SUNWemlxs........................

done.

13.19

Mbytes remaining.

 

 

 

 

SUNWemlxu........................

done.

12.50

Mbytes remaining.

 

 

 

 

SUNWerid.........................

done.

12.35

Mbytes remaining.

 

 

 

 

SUNWeuodf........................

done.

12.23

Mbytes remaining.

 

 

 

 

SUNWfchbar.......................

done.

12.20

Mbytes remaining.

 

 

 

 

SUNWfchba........................

done.

10.63

Mbytes remaining.

 

 

 

 

SUNWfcip.........................

done.

10.44

Mbytes remaining.

 

 

 

 

SUNWfcmdb........................

done.

10.24

Mbytes remaining.

 

 

 

 

SUNWfcp..........................

done.

9.95

Mbytes remaining.

 

 

 

 

SUNWfcprt........................

done.

9.88

Mbytes remaining.

 

 

 

 

SUNWfcsm.........................

done.

9.73

Mbytes remaining.

 

 

 

 

SUNWopenssl-commands.............

done.

9.35

Mbytes remaining.

 

 

 

 

SUNWopensslr.....................

done.

9.30

Mbytes remaining.

 

 

 

 

SUNWpd...........................

done.

8.64

Mbytes remaining.

 

 

 

 

SUNWfss..........................

done.

8.53

Mbytes remaining.

 

 

 

 

SUNWpiclr........................

done.

8.50

Mbytes remaining.

 

 

 

 

SUNWpkgcmdsr.....................

done.

8.46

Mbytes remaining.

 

 

 

 

SUNWpkgcmdsu.....................

done.

5.72

Mbytes remaining.

 

 

 

 

SUNWged..........................

done.

5.47

Mbytes remaining.

 

 

 

 

SUNWqfed.........................

done.

5.25

Mbytes remaining.

 

 

 

 

SUNWqlc..........................

done.

4.05

Mbytes remaining.

 

 

 

 

SUNWqlcu.........................

done.

4.00

Mbytes remaining.

 

 

 

 

SUNWqos..........................

done.

3.83

Mbytes remaining.

 

 

 

 

SUNWqosu.........................

done.

3.71

Mbytes remaining.

 

 

 

 

SUNWqus..........................

done.

3.48

Mbytes remaining.

 

 

 

 

SUNWqusu.........................

done.

3.45

Mbytes remaining.

 

 

 

 

SUNWrcmdr........................

done.

3.37

Mbytes remaining.

 

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

2-10

 

 

 

 

OL-18083-01

 

 

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

SUNWrge..........................

done.

3.26

Mbytes remaining.

SUNWroute........................

done.

2.94

Mbytes remaining.

SUNWrpcib........................

done.

2.79

Mbytes remaining.

SUNWrsgk.........................

done.

2.72

Mbytes remaining.

SUNWsolnm........................

done.

2.70

Mbytes remaining.

SUNWsshcu........................

done.

2.27

Mbytes remaining.

SUNWsshdr........................

done.

2.20

Mbytes remaining.

SUNWsshdu........................

done.

1.79

Mbytes remaining.

SUNWspnego.......................

done.

1.68

Mbytes remaining.

SUNWsshr.........................

done.

1.57

Mbytes remaining.

SUNWsshu.........................

done.

1.00

Mbytes remaining.

Completed software installation

Solaris 10 software installation succeeded

Customizing system files

-Mount points table (/etc/vfstab)

-Unselected disk mount points (/var/sadm/system/data/vfstab.unselected)

-Network host addresses (/etc/hosts)

-Network host addresses (/etc/hosts)

-Environment variables (/etc/default/init)

Cleaning devices

Customizing system devices

-Physical devices (/devices)

-Logical devices (/dev)

Installing boot information

-Installing boot blocks (c1t0d0s0)

-Updating system firmware for automatic rebooting

Installation log location

-/a/var/sadm/system/logs/install_log (before reboot)

-/var/sadm/system/logs/install_log (after reboot)

Installation complete

Executing SolStart postinstall phase...

Executing finish script "patch_finish"...

Finish script patch_finish execution completed.

Executing JumpStart postinstall phase...

Executing finish script "any_finish"...

any_finish started with SI_CONFIG_DIR = /tmp/install_config any_finish completed

Finish script any_finish execution completed.

The begin script log 'begin.log'

is located in /var/sadm/system/logs after reboot.

The finish script log 'finish.log'

is located in /var/sadm/system/logs after reboot.

syncing file systems... done

rebooting...

SC Alert: Host System has Reset

Probing system devices

Probing memory

Probing I/O buses

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-11

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Sun Fire V210, No Keyboard

Copyright 2005 Sun Microsystems, Inc. All rights reserved.

OpenBoot 4.18.5, 2048 MB memory installed, Serial #52030991.

Ethernet address 0:3:ba:19:ee:f, Host ID: 8319ee0f.

Initializing

1MB of memory at addr

103feec000

Initializing

1MB of memory at addr

103fee0000

Initializing

15MB of memory at addr

103f002000

Initializing

16MB of memory at addr

103e002000

Initializing

992MB of memory at addr

1000000000

Initializing

1024MB of memory at addr

0

Rebooting with command: boot

Boot device: /pci@1c,600000/scsi@2/disk@0,0:a File and args:

SunOS Release 5.10 Version Generic_118833-1764-bit

Copyright 1983-2005Sun Microsystems, Inc. All rights reserved.

Use is subject to license terms.

Hardware watchdog enabled Hostname: vtghost Configuring devices.

Loading smf(5) service descriptions: 1/85 2/85 3/85

...

84/85

85/85

checking ufs filesystems /dev/rdsk/c1t0d0s5: is logging.

Creating new rsa public/private host key pair Creating new dsa public/private host key pair

This system is configured with NFS version 4, which uses a domain name that is automatically derived from the system's name services. The derived domain name is sufficient for most configurations. In a few cases, mounts that cross different domains might cause files to be owned by "nobody" due to the lack of a common domain name.

Do you need to override the system's default NFS version 4 domain name (yes/no) ? [no] :

Step 7 Enterno to continue the reconfiguration process and pressEnter.

The system displays information similar to the following:

For more information about how the NFS version 4 default domain name is derived and its impact, refer to the man pages for nfs(4) and nfsmapid(1m), and the System Administration Guide: Network Services.

vtghost console login:

This completes the installation of the Sun Solaris 10 operating system. Proceed to the “Configuring Your Host” section on page 2-50.

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-12

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Installing the Sun Solaris 10 Operating System for Opteron-basedPlatforms

The instructions in this section were written to correspond with the instructions in the Cisco Solaris 10 Operating System Startup Disk for Opteron-basedPlatforms. Other Solaris installations are similar, with slight variations. These instructions will note the differences between the sets of installation instructions.

Step 1 Choose one of the following options to connect the Cisco PGW 2200 Softswitch:

Connect to the Cisco PGW 2200 Softswitch through a console port.

Connect a keyboard and monitor to the Cisco PGW 2200 Softswitch.

Note Cisco recommends that you connect to the Cisco PGW 2200 Softswitch using a keyboard and monitor. If you choose to connect through the console port, you need to ensure that Console Redirection is enabled as instructed inStep 6.

Step 2 Follow these steps to connect to the target system through a serial port:

a. Log in to the SP (Service Processor) as an Administrator:

login: root password:changeme

b. Type the following command to start the ILOM Service Processor (SP) GUI:

start /SP/console

Step 3 This step isoptional—ifyou decide to skip this, go toStep 4.

a.Place the system in single-usermode by shutting down the standby machine.

b.When the machine prompts for a password, type either ^ -d to proceed with normal startup, or the root password for system maintenance.

Step 4 Load the appropriate version of theCD-ROMlabeled Cisco Solaris 10 Operating Software Startup Disk forOpteron-basedPlatforms into theCD-ROMdrive.

Step 5 If the system is currently running, log in asroot.

Step 6 Boot the system from theCD-ROMdrive by entering the appropriate command:

# reboot

Note You may be prompted during the reboot to enterCtrl-B orCtrl-C to open configuration tools for your hardware. You do not need to open any of these tools to complete this installation.

Perform the following steps once the reboot starts:

a.Press the F2 key to open the Setup menu. The Setup menu opens after theself-testshave been completed.

b.Go to the BOOT setup information.

c.Ensure that the CD-ROMis the first bootable device in the list.

d.Choose the Advanced menu from the category selections at the top of the screen.

e.If you connected to the Cisco PGW 2200 Softswitch using the console port, ensure Console Redirection is set to enable oralways.

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-13

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

f. Save your changes and exit the Setup menu.

Information similar to the following is displayed:

SSC Alert: Host System has Reset

screen not found. keyboard not found.

Keyboard not present. Using ttya for input and output.

Caution Ensure that the selected display device is set to the corresponding console device. If you use a monitor, choosesolaris. If you use serial console, selectsolaris ttya.

SunFire V40z, No Keyboard

Copyright 1998-2004Sun Microsystems, Inc. All rights reserved.

OpenBoot 4.13.0, 8192 MB memory installed, Serial #58524225.

Ethernet address 0:3:ba:7d:2:41, Host ID: 837d0241.

Rebooting with command: boot cdrom - install

Boot device: /pci@1e,600000/ide@d/cdrom@0,0:f File and args: - install

SunOS Release 5.10 Version Generic 64-bit

Copyright 1983-2005Sun Microsystems, Inc. All rights reserved.

Use is subject to license terms.

Hardware watchdog enabled

Configuring devices.

Using RPC Bootparams for network configuration information.

Attempting to configure interface ce2...

Skipped interface ce2

Attempting to configure interface ce1...

Skipped interface ce1

Attempting to configure interface ce0...

Skipped interface ce0

Beginning system identification...

Searching for configuration file(s)...

Search complete.

Discovering additional network configuration...

Completing system identification...

Starting remote procedure call (RPC) services: done.

System identification complete.

Starting Solaris installation program...

Searching for JumpStart directory...

<<< using cdrom install_config >>>

not found

Checking rules.ok file...

Using profile: any_machine

Using finish script: any_finish

Executing JumpStart preinstall phase...

Searching for SolStart directory...

Checking rules.ok file...

Executing profile begin script...

Completed profile begin script.

Processing profile

-Selecting cluster (SUNWCreq)

-Deselecting cluster (SUNWCudf)

-Deselecting cluster (SUNWCbs)

-Deselecting cluster (SUNWCnfss)

-Deselecting cluster (SUNWCsndm)

-Deselecting cluster (SUNWCpcmc)

-Deselecting cluster (SUNWCpicl)

-Selecting cluster (SUNWCacc)

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-14

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

-Selecting cluster (SUNWCssh)

-Selecting cluster (SUNWCpool)

-Selecting cluster (SUNWCvld)

-Selecting cluster (SUNWCfwshl)

-Selecting cluster (SUNWClu)

-Selecting cluster (SUNWCcpc)

-Selecting cluster (SUNWCsea)

-Selecting cluster (SUNWCstl)

-Selecting cluster (SUNWCmip)

-Selecting cluster (SUNWCqos)

-Selecting cluster (SUNWCzone)

-Selecting cluster (SUNWCzebra)

-Deselecting package (SUNWauda)

-Deselecting package (SUNWad810)

-Deselecting package (SUNWvia823x)

-Deselecting package (SUNWcnsu)

-Deselecting package (SUNWtnamd)

-Deselecting package (SUNWtnamr)

-Deselecting package (SUNWrcmdr)

-Deselecting package (SUNWrcmds)

-Deselecting package (SUNWtftp)

-Deselecting package (SUNWtftpr)

-Deselecting package (SUNWcnsr)

-Deselecting package (SUNWatfsr)

-Deselecting package (SUNWatfsu)

-Deselecting package (SUNWftpr)

-Deselecting package (SUNWftpu)

-Deselecting package (SUNWipmi)

-Deselecting package (SUNWxsvc)

-Deselecting package (SUNWflexruntime)

-Deselecting package (SUNWxwmod)

-Selecting package (SUNWadmc)

-Selecting package (SUNWadmfr)

-Selecting package (SUNWadmfw)

-Selecting package (SUNWdtdmr)

-Selecting package (SUNWxwfnt)

-Selecting package (SUNWzip)

-Selecting package (SUNWless)

-Selecting package (SUNWeurf)

-Selecting package (SUNWj5rt)

-Selecting package (SUNWxwacx)

-Selecting package (SUNWxwice)

-Selecting package (SUNWxwplr)

-Selecting package (SUNWxwrtl)

-Selecting package (SUNWxwplt)

-Selecting package (SUNWxi18n)

-Selecting package (SUNWtltk)

-Selecting package (SUNWeuodf)

-Selecting package (SUNWocf)

-Selecting package (SUNWocfr)

-Selecting package (SUNWbtool)

-Selecting package (SUNWsprot)

-Selecting package (SUNWmdbdm)

-Selecting package (SUNWmkcd)

-Selecting package (SUNWspnego)

-Selecting package (SUNWtnfc)

-Selecting package (SUNWtnfd)

-Selecting package (SUNWbind)

-Selecting package (SUNWbindr)

-Selecting package (SUNWctpls)

-Selecting package (SUNWfss)

-Selecting package (SUNWgcmn)

-Selecting package (SUNWgssdh)

-Selecting package (SUNWgssk)

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-15

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

-Selecting package (SUNWinst)

-Selecting package (SUNWi15rf)

-Selecting package (SUNWipc)

-Selecting package (SUNWmdbr)

-Selecting package (SUNWmfrun)

-Selecting package (SUNWrsg)

-Selecting package (SUNWrsgk)

-Selecting package (SUNWter)

-Selecting package (SUNWtoo)

-Selecting package (SUNW1394)

-Selecting all disks

-Configuring boot device

-Using disk (c1t0d0) for "rootdisk"

-Deleting Solaris fdisk partition (c1t0d0)

-Deleting Solaris fdisk partition (c1t1d0)

-Creating "all" Solaris fdisk partition (c1t0d0)

-Creating "all" Solaris fdisk partition (c1t1d0)

-Configuring / (c1t0d0s0)

-Configuring /var (c1t0d0s1)

-Configuring swap (c1t0d0s3)

-

Configuring

(c1t0d0s4)

-

Configuring

(c1t0d0s6)

-Configuring /opt (c1t0d0s5)

-Deselecting unmodified disk (c1t1d0)

Verifying disk configuration

Verifying space allocation

- Total software size: 420.10 Mbytes

You may need to eject the CD or select a different boot device after reboot to avoid repeating the installation process.

Configuring disk (c1t0d0)

- Creating Fdisk partition table

Fdisk partition table for disk c1t0d0 (input file for fdisk(1M))

type: 130

active:

128

offset: 16065

size: 143347995

type: 100

active:

0

offset: 0

size: 0

type:

100

active:

0

offset:

0

size:

0

type:

100

active:

0

offset:

0

size:

0

- Creating Solaris disk label (VTOC)

Creating and checking UFS file systems - Creating / (c1t0d0s0)

Warning: 1474 sector(s) in last cylinder unallocated /dev/rdsk/c1t0d0s0:4096574 sectors in 667 cylinders of 48 tracks, 128 sectors

 

 

 

2000.3MB in 42 cyl groups (16 c/g, 48.00MB/g, 11648 i/g)

 

 

 

 

 

 

 

super-blockbackups (for fsck-Fufs-ob=#) at:

 

 

 

 

 

 

32,

98464,

196896,

295328,

393760,

492192,

590624,

689056,

787488,

885920,

 

3149856, 3248288,

3346720,

3445152,

3543584,

3642016,

3740448,

3838880,

 

3937312, 4035744

 

 

 

 

 

 

 

 

 

 

 

 

 

 

- Creating /var (c1t0d0s1)

 

 

 

 

 

 

 

 

 

 

 

 

Warning: 4866 sector(s) in last cylinder unallocated

 

 

 

 

 

 

 

 

 

/dev/rdsk/c1t0d0s1:10249470 sectors in 1669 cylinders of 48 tracks, 128 sectors

 

 

 

5004.6MB in 105 cyl groups (16 c/g, 48.00MB/g, 5824 i/g)

 

 

 

 

 

 

 

super-blockbackups (for fsck-Fufs-ob=#) at:

 

 

 

 

 

 

32,

98464,

196896,

295328,

393760,

492192,

590624,

689056,

787488,

885920,

 

9342880, 9441312,

9539744,

9638176,

9736608,

9835040,

9933472,

10031904,

 

10130336,

10228768

 

 

 

 

 

 

 

 

 

 

 

 

 

 

- Creating /opt (c1t0d0s5)

 

 

 

 

 

 

 

 

 

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

2-16

 

 

 

 

 

 

 

 

 

 

 

 

 

OL-18083-01

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Warning: 1062 sector(s) in last cylinder unallocated

/dev/rdsk/c1t0d0s5:116599770 sectors in 18978 cylinders of 48 tracks, 128 sectors 56933.5MB in 1187 cyl groups (16 c/g, 48.00MB/g, 5824 i/g)

super-blockbackups (for fsck-Fufs-ob=#) at:

32, 98464, 196896, 295328, 393760, 492192, 590624, 689056, 787488, 885920, Initializing cylinder groups:

.......................

super-blockbackups for last 10 cylinder groups at:

115707040, 115805472, 115903904, 116002336, 116100768, 116199200, 116297632, 116396064, 116494496, 116592928

Beginning Solaris software installation 23303 blocks

Installation of <SUNWcsu> was successful. 5043 blocks

Installation of <SUNWcsr> was successful. 21985 blocks

Installation of <SUNWcsl> was successful. 75 blocks

Installation of <SUNWcnetr> was successful. 43978 blocks

 

 

Installation of <SUNWckr> was successful.

 

 

30 blocks

 

 

Installation of <SUNWkvm> was successful.

 

 

Installation of <SUNWcar> was successful.

 

 

Installation of <SUNWcakr> was successful.

 

 

7 blocks

 

 

add c devices/pseudo/arp@0:arp (44, 0) 0666 root sys

 

 

add link /dev/arp=../devices/pseudo/arp@0:arp

 

 

add c devices/pseudo/clone@0:ibd (11, 170) 0666 root sys

 

 

add link /dev/ibd=../devices/pseudo/clone@0:ibd

 

 

add c devices/pseudo/icmp@0:icmp (5, 0) 0666 root sys

 

 

add link /dev/icmp=../devices/pseudo/icmp@0:icmp

 

 

add c devices/pseudo/icmp@0:icmp (5, 0) 0666 root sys

 

 

add link /dev/rawip=../devices/pseudo/icmp@0:icmp

 

 

add c devices/pseudo/icmp6@0:icmp6 (140, 1) 0666 root sys

 

 

add link /dev/icmp6=../devices/pseudo/icmp6@0:icmp6

 

 

add c devices/pseudo/icmp6@0:icmp6 (140, 1) 0666 root sys

 

 

add link /dev/rawip6=../devices/pseudo/icmp6@0:icmp6

 

 

add c devices/pseudo/ip@0:ip (3, 0) 0666 root sys

 

 

add link /dev/ip=../devices/pseudo/ip@0:ip

 

 

add c devices/pseudo/ip6@0:ip6 (139, 1) 0666 root sys

 

 

add link /dev/ip6=../devices/pseudo/ip6@0:ip6

 

 

add c devices/pseudo/rts@0:rts (43, 0) 0666 root sys

 

 

add link /dev/rts=../devices/pseudo/rts@0:rts

 

 

add c devices/pseudo/tcp@0:tcp (42, 2) 0666 root sys

 

 

add link /dev/tcp=../devices/pseudo/tcp@0:tcp

 

 

add c devices/pseudo/tcp6@0:tcp6 (142, 3) 0666 root sys

 

 

add link /dev/tcp6=../devices/pseudo/tcp6@0:tcp6

 

 

add c devices/pseudo/udp@0:udp (41, 0) 0666 root sys

 

 

add link /dev/udp=../devices/pseudo/udp@0:udp

 

 

add c devices/pseudo/udp6@0:udp6 (141, 1) 0666 root sys

 

 

add link /dev/udp6=../devices/pseudo/udp6@0:udp6

 

 

add c devices/pseudo/ipsecah@0:ipsecah (137, 1) 0666 root sys

 

 

add link /dev/ipsecah=../devices/pseudo/ipsecah@0:ipsecah

 

 

add c devices/pseudo/ipsecesp@0:ipsecesp (138, 1) 0666 root sys

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-17

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

add link /dev/ipsecesp=../devices/pseudo/ipsecesp@0:ipsecesp add c devices/pseudo/keysock@0:keysock (136, 0) 0666 root sys add link /dev/keysock=../devices/pseudo/keysock@0:keysock add c devices/pseudo/cn@0:console (0, 0) 0620 root tty

add link /dev/console=../devices/pseudo/cn@0:console add c devices/pseudo/cn@0:syscon (0, 0) 0620 root tty add link /dev/syscon=../devices/pseudo/cn@0:syscon add c devices/pseudo/cn@0:systty (0, 0) 0620 root tty add link /dev/systty=../devices/pseudo/cn@0:systty

add c devices/pseudo/devinfo@0:devinfo (88, 0) 0640 root sys add c devices/pseudo/ksyms@0:ksyms (72, 0) 0666 root sys add link /dev/ksyms=../devices/pseudo/ksyms@0:ksyms

add c devices/pseudo/log@0:conslog (21, 0) 0666 root sys add link /dev/conslog=../devices/pseudo/log@0:conslog add c devices/pseudo/log@0:log (21, 5) 0640 root sys

add link /dev/log=../devices/pseudo/log@0:log

add c devices/pseudo/mm@0:mem (13, 0) 0640 root sys add link /dev/mem=../devices/pseudo/mm@0:mem

add c devices/pseudo/mm@0:kmem (13, 1) 0640 root sys add link /dev/kmem=../devices/pseudo/mm@0:kmem

add c devices/pseudo/mm@0:null (13, 2) 0666 root sys add link /dev/null=../devices/pseudo/mm@0:null

add c devices/pseudo/mm@0:allkmem (13, 3) 0600 root sys add link /dev/allkmem=../devices/pseudo/mm@0:allkmem add c devices/pseudo/mm@0:zero (13, 12) 0666 root sys add link /dev/zero=../devices/pseudo/mm@0:zero

add c devices/pseudo/openeepr@0:openprom (6, 0) 0640 root sys add link /dev/openprom=../devices/pseudo/openeepr@0:openprom add c devices/pseudo/sad@0:admin (12, 1) 0666 root sys

add link /dev/sad/admin=../../devices/pseudo/sad@0:admin add c devices/pseudo/sad@0:user (12, 0) 0666 root sys add link /dev/sad/user=../../devices/pseudo/sad@0:user add c devices/pseudo/sy@0:tty (22, 0) 0666 root tty

add link /dev/tty=../devices/pseudo/sy@0:tty

add c devices/pseudo/sysevent@0:sysevent (152, 0) 0600 root sys add link /dev/sysevent=../devices/pseudo/sysevent@0:sysevent add c devices/pseudo/sysmsg@0:msglog (97, 1) 0600 root sys

add link /dev/msglog=../devices/pseudo/sysmsg@0:msglog

add c devices/pseudo/sysmsg@0:sysmsg (97, 0) 0600 root sys add link /dev/sysmsg=../devices/pseudo/sysmsg@0:sysmsg

add c devices/pseudo/tl@0:ticots (105, 0) 0666 root sys add link /dev/ticots=../devices/pseudo/tl@0:ticots

add c devices/pseudo/tl@0:ticotsord (105, 1) 0666 root sys add link /dev/ticotsord=../devices/pseudo/tl@0:ticotsord add c devices/pseudo/tl@0:ticlts (105, 2) 0666 root sys add link /dev/ticlts=../devices/pseudo/tl@0:ticlts

add c devices/pseudo/wc@0:wscons (15, 0) 0600 root sys add link /dev/wscons=../devices/pseudo/wc@0:wscons

add c devices/pseudo/conskbd@0:kbd (103, 0) 0666 root sys add link /dev/kbd=../devices/pseudo/conskbd@0:kbd

Installation of <SUNWcsd> was successful. 422 blocks

Installation of <SUNWzlib> was successful. 3826 blocks

Installation of <SUNWlibmsr> was successful.

Installation of <SUNWlibms> was successful. 5495 blocks

Installation of <SUNWlxml> was successful.

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-18

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Installation of <SUNWxwrtl> was successful.

Installation of <SUNWbzip> was successful. 22155 blocks

Installation of <SUNWxwfnt> was successful. 440 blocks

Installation of <SUNWxwice> was successful. 63 blocks

Installation of <SUNWxwdv> was successful. 3 blocks

Installation of <SUNWxwplr> was successful. 8688 blocks

Installation of <SUNWperl584core> was successful. 39013 blocks

Installation of <SUNWperl584usr> was successful. 3641 blocks

Installation of <SUNWesu> was successful. 118 blocks

Installation of <SUNWcpp> was successful.

Installation of <SUNWdtcor> was successful. 31656 blocks

Installation of <SUNWxwplt> was successful. 1019 blocks

Installation of <SUNWlexpt> was successful.

Installation of <SUNWgcmn> was successful. 116 blocks

Installation of <SUNWctpls> was successful. 18841 blocks

Installation of <SUNWmfrun> was successful. 260 blocks

Installation of <SUNWxwacx> was successful. 3 blocks

Installation of <SUNWsshdr> was successful. 390 blocks

Installation of <SUNWadmlib-sysid>was successful. 27 blocks

Installation of <SUNWadmr> was successful. 3755 blocks

Installation of <SUNWadmap> was successful.

Installation of <SUNWgssc> was successful. 554 blocks

Installation of <SUNWgss> was successful. 11613 blocks

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-19

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Installation of <SUNWopenssl-libraries>was successful. 687 blocks

Installation of <SUNWsshcu> was successful. 694 blocks

Installation of <SUNWsshdu> was successful.

Installation of <SUNWdtdmr> was successful. 6063 blocks

Installation of <SUNWtltk> was successful. 134 blocks

Installation of <SUNWgzip> was successful. 173 blocks

Installation of <SUNWsshr> was successful. 970 blocks

Installation of <SUNWsshu> was successful. 11214 blocks

Installation of <SUNWlibC> was successful. 151975 blocks

Installation of <SUNWj5rt> was successful. 580 blocks

Installation of <SUNWwbsup> was successful.

Installation of <SUNWinstall-patch-utils-root>was successful.

Installation of <SUNWswmt> was successful. 5206 blocks

Installation of <SUNWmdr> was successful. 1139 blocks

Installation of <SUNWmdu> was successful. 2937 blocks

Installation of <SUNWadmc> was successful. 4275 blocks

Installation of <SUNWnfsckr> was successful. 89 blocks

Installation of <SUNWnfscr> was successful. 426 blocks

Installation of <SUNWnfscu> was successful. 8 blocks

Installation of <SUNWkrbr> was successful. 3840 blocks

Installation of <SUNWkrbu> was successful. 259 blocks

Installation of <SUNWbip> was successful. 237 blocks

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-20

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Installation of <SUNWtnetc> was successful. 1498 blocks

Installation of <SUNWrcmdc> was successful. 4857 blocks

Reboot client to install driver.

Installation of <SUNWib> was successful. 2431 blocks

Reboot client to install driver.

Installation of <SUNWtavor> was successful. 599 blocks

Installation of <SUNWtcsh> was successful. 1085 blocks

Installation of <SUNWtecla> was successful. 1978 blocks

Installation of <SUNWter> was successful. 1975 blocks

Installation of <SUNWpr> was successful. 10669 blocks

Installation of <SUNWtls> was successful. 90 blocks

Installation of <SUNWtnetd> was successful.

Installation of <SUNWtnetr> was successful. 1039 blocks

Installation of <SUNWtnfc> was successful. 97 blocks

Installation of <SUNWtnfd> was successful. 1784 blocks

Installation of <SUNWtoo> was successful.

Installation of <SUNWucbt> was successful.

Installation of <SUNWudaplr> was successful. 382 blocks

Installation of <SUNWudaplu> was successful. 256 blocks

Installation of <SUNWipoib> was successful. 680 blocks

Installation of <SUNWudapltu> was successful. 559 blocks

Reboot client to install driver.

Installation of <SUNWudapltr> was successful.

Installation of <SUNWocfr> was successful. 974 blocks

Installation of <SUNWocf> was successful. 1580 blocks

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-21

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Reboot client to install driver.

Reboot client to install driver.

Reboot client to install driver.

Reboot client to install driver.

Reboot client to install driver.

Reboot client to install driver.

Reboot client to install driver.

Reboot client to install driver.

Reboot client to install driver.

Removing empty OWconfig

Installation of <SUNWos86r> was successful.

Installation of <SUNWrmodr> was successful.

Reboot client to install driver.

Installation of <CADP160> was successful. 1069 blocks

Reboot client to install driver.

Installation of <SUNWaudd> was successful. 3863 blocks

Reboot client to install driver. Reboot client to install driver. Reboot client to install driver. Reboot client to install driver. Reboot client to install driver. Reboot client to install driver. Reboot client to install driver. Reboot client to install driver. Reboot client to install driver. Reboot client to install driver.

Installation of <SUNWusb> was successful. 138 blocks

Installation of <SUNWusbs> was successful. 465 blocks

Reboot client to install driver.

Installation of <SUNWuedg> was successful. 732 blocks

Modifying /a/kernel/drv/sd.conf Reboot client to install driver.

Installation of <HPFC> was successful. 66 blocks

Installation of <NCRos86r> was successful. 151 blocks

Reboot client to install driver.

Installation of <SUNWugen> was successful. 379 blocks

Reboot client to install driver.

Installation of <SK98sol> was successful. 679 blocks

Reboot client to install driver.

Installation of <SKfp> was successful. 8309 blocks

Installation of <SUNWeurf> was successful.

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-22

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

2429 blocks

Reboot client to install driver.

Installation of <SUNW1394> was successful. 1423 blocks

Installation of <SUNWxi18n> was successful. 95 blocks

Installation of <SUNWvld> was successful. 40 blocks

Installation of <SUNWvldu> was successful. 1198 blocks

Installation of <SUNWbash> was successful.

Installation of <SUNWproduct-registry-root>was successful. 817 blocks

registry conversion not required

Installation of <SUNWwsr2> was successful. 158 blocks

Reboot client to install driver.

Installation of <SUNWaac> was successful. 3 blocks

Installation of <SUNWaccr> was successful. 511 blocks

Installation of <SUNWaccu> was successful.

Installation of <SUNWgrub> was successful.

Installation of <SUNWadmfr> was successful. 1167 blocks

Installation of <SUNWadmfw> was successful. 80 blocks

Installation of <SUNWi15rf> was successful.

Reboot client to install driver.

Installation of <SUNWadp> was successful.

Installation of <SUNWradpu320> was successful. 1216 blocks

Reboot client to install driver.

Installation of <SUNWadpu320> was successful. 136 blocks

Reboot client to install driver.

Installation of <SUNWamr> was successful. 2519 blocks

Installation of <SUNWsprot> was successful. 190 blocks

Installation of <SUNWrsg> was successful. 453 blocks

Installation of <SUNWgssdh> was successful.

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-23

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

671 blocks

Installation of <SUNWgssk> was successful. 1251 blocks

Reboot client to install driver.

Installation of <SUNWxge> was successful. 2194 blocks

Installation of <SUNWbtool> was successful. 24616 blocks

Installation of <SUNWcslr> was successful. 1022 blocks

Installation of <SUNWidnl> was successful. 1830 blocks

Installation of <SUNWinst> was successful. 596 blocks

Reboot client to install driver.

Installation of <SUNWintgige> was successful. 41 blocks

Installation of <SUNWipc> was successful. 119 blocks

Installation of <SUNWipfr> was successful. 3499 blocks

Installation of <SUNWipfu> was successful. 6407 blocks

/a/etc/lu/synclist Installing /a/etc/default/lu

Installation of <SUNWlur> was successful. 3495 blocks

Installation of <SUNWluu> was successful.

Reboot client to install driver.

Installation of <SUNWiscsir> was successful.

Installation of <SUNWiscsiu> was successful. 790 blocks

Installation of <SUNWloc> was successful. 83 blocks

Installation of <SUNWnisr> was successful. 3891 blocks

Installation of <SUNWnisu> was successful. 45 blocks

Installation of <SUNWzebrar> was successful. 4056 blocks

Installation of <SUNWzebrau> was successful. 267 blocks

Installation of <SUNWzip> was successful. 9 blocks

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-24

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Installation of <SUNWzoner> was successful. 606 blocks

Installation of <SUNWluzone> was successful.

Installation of <SUNWpoolr> was successful. 1366 blocks

Installation of <SUNWpool> was successful. 878 blocks

Installation of <SUNWzoneu> was successful. 4985 blocks

Installation of <SUNWzsh> was successful.

Reboot client to install driver.

Installation of <SYMhisl> was successful. 72 blocks

Installation of <SUNWcpc> was successful.

Installation of <SUNWbindr> was successful. 4546 blocks

Installation of <SUNWbind> was successful.

Installation of <SUNWbipr> was successful.

Reboot client to install driver.

Installation of <SUNWcadp> was successful. 955 blocks

Reboot client to install driver.

Installation of <SUNWced> was successful. 161 blocks

Installation of <SUNWcfcl> was successful.

Installation of <SUNWcfclr> was successful. 253 blocks

Installation of <SUNWluxop> was successful. 594 blocks

Installation of <SUNWcfpl> was successful. 2 blocks

Installation of <SUNWcfplr> was successful. 3979 blocks

Installation of <SUNWjss> was successful. 918 blocks

Installation of <SUNWcpcu> was successful. 29 blocks

Reboot client to install driver.

Installation of <SUNWcqhpc> was successful. 215 blocks

Installation of <SUNWkey> was successful. 128 blocks

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-25

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Installation of <SUNWeuodf> was successful. 231 blocks

Installation of <SUNWless> was successful. 184 blocks

Installation of <SUNWcstl> was successful. 928 blocks

Installation of <SUNWlibsasl> was successful. 314 blocks

Installation of <SUNWlldap> was successful. 228 blocks

Reboot client to install driver.

Installation of <SUNWlsimega> was successful. 10159 blocks

Installation of <SUNWmdb> was successful. 29 blocks

Installation of <SUNWmdbdm> was successful. 6853 blocks

Installation of <SUNWmdbr> was successful. 3972 blocks

Installation of <SUNWdtrc> was successful. 1313 blocks

Installation of <SUNWdtrp> was successful. 1227 blocks

Reboot client to install driver.

Installation of <SUNWfctl> was successful. 3552 blocks

Reboot client to install driver.

Installation of <SUNWemlxs> was successful. 2568 blocks

Installation of <SUNWemlxu> was successful. 174 blocks

Installation of <SUNWmibii> was successful. 1332 blocks

Installation of <SUNWsasnm> was successful. 1106 blocks

Installation of <SUNWsadmi> was successful. 328 blocks

Installation of <SUNWsacom> was successful. 40 blocks

Installation of <SUNWmipr> was successful. 468 blocks

Installation of <SUNWmipu> was successful. 844 blocks

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-26

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Installation of <SUNWmkcd> was successful.

Modifying /a/etc/hba.conf

Installation of <SUNWfchbar> was successful. 3366 blocks

Installation of <SUNWfchba> was successful. 537 blocks

Reboot client to install driver.

Installation of <SUNWfcip> was successful. 312 blocks

Installation of <SUNWfcmdb> was successful. 803 blocks

Reboot client to install driver.

Installation of <SUNWfcp> was successful. 79 blocks

Installation of <SUNWfcprt> was successful. 361 blocks

Reboot client to install driver.

Installation of <SUNWfcsm> was successful. 3020 blocks

Installation of <SUNWfmd> was successful. 197 blocks

Installation of <SUNWfss> was successful. 275 blocks

Reboot client to install driver.

Installation of <SUNWnge> was successful. 1 blocks

Installation of <SUNWpkgcmdsr> was successful. 4530 blocks

Installation of <SUNWpkgcmdsu> was successful. 1509 blocks

Reboot client to install driver.

Installation of <SUNWpsdcr> was successful.

Installation of <SUNWsolnm> was successful. 590 blocks

Reboot client to install driver.

Installation of <SUNWpsdir> was successful. 3866 blocks

Reboot client to install driver.

Installation of <SUNWqlc> was successful. 387 blocks

Installation of <SUNWqos> was successful. 136 blocks

Installation of <SUNWqosu> was successful. 2 blocks

Installation of <SUNWrmodu> was successful.

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-27

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

497 blocks

Installation of <SUNWroute> was successful. 271 blocks

Reboot client to install driver.

Installation of <SUNWrpcib> was successful. 145 blocks

Installation of <SUNWrsgk> was successful. 89 blocks

Reboot client to install driver.

Installation of <SUNWrtls> was successful. 125 blocks

Installation of <SUNWspnego> was successful.

Solaris 10 software installation succeeded

Solaris 10 packages fully installed

SUNWcsu

SUNWcsr

SUNWcsl

SUNWcnetr

SUNWckr

SUNWkvm

SUNWcar

SUNWcakr

SUNWcsd

SUNWzlib

SUNWlibmsr

SUNWlibms

SUNWlxml

SUNWxwrtl

SUNWbzip

SUNWxwfnt

SUNWxwice

SUNWxwdv

SUNWxwplr

SUNWperl584core

SUNWperl584usr

SUNWesu

SUNWcpp

SUNWdtcor

SUNWxwplt

SUNWlexpt

SUNWgcmn

SUNWctpls

SUNWmfrun

SUNWxwacx

SUNWsshdr

SUNWadmlib-sysid

SUNWadmr

SUNWadmap

SUNWgssc

SUNWgss

SUNWopenssl-libraries

SUNWsshcu

SUNWsshdu

SUNWdtdmr

SUNWtltk

SUNWgzip

SUNWsshr

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-28

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

SUNWsshu

SUNWlibC

SUNWj5rt

SUNWwbsup

SUNWinstall-patch-utils-root

SUNWswmt

SUNWmdr

SUNWmdu

SUNWadmc

SUNWnfsckr

SUNWnfscr

SUNWnfscu

SUNWkrbr

SUNWkrbu

SUNWbip

SUNWtnetc

SUNWrcmdc

SUNWib

SUNWtavor

SUNWtcsh

SUNWtecla

SUNWter

SUNWpr

SUNWtls

SUNWtnetd

SUNWtnetr

SUNWtnfc

SUNWtnfd

SUNWtoo

SUNWucbt

SUNWudaplr

SUNWudaplu

SUNWipoib

SUNWudapltu

SUNWudapltr

SUNWocfr

SUNWocf

SUNWos86r

SUNWrmodr

CADP160

SUNWaudd

SUNWusb

SUNWusbs

SUNWuedg

HPFC

NCRos86r

SUNWugen

SK98sol

SKfp

SUNWeurf

SUNW1394

SUNWxi18n

SUNWvld

SUNWvldu

SUNWbash

SUNWproduct-registry-root

SUNWwsr2

SUNWaac

SUNWaccr

SUNWaccu

SUNWgrub

SUNWadmfr

SUNWadmfw

SUNWi15rf

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-29

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

SUNWadp

SUNWradpu320

SUNWadpu320

SUNWamr

SUNWsprot

SUNWrsg

SUNWgssdh

SUNWgssk

SUNWxge

SUNWbtool

SUNWcslr

SUNWidnl

SUNWinst

SUNWintgige

SUNWipc

SUNWipfr

SUNWipfu

SUNWlur

SUNWluu

SUNWiscsir

SUNWiscsiu

SUNWloc

SUNWnisr

SUNWnisu

SUNWzebrar

SUNWzebrau

SUNWzip

SUNWzoner

SUNWluzone

SUNWpoolr

SUNWpool

SUNWzoneu

SUNWzsh

SYMhisl

SUNWcpc

SUNWbindr

SUNWbind

SUNWbipr

SUNWcadp

SUNWced

SUNWcfcl

SUNWcfclr

SUNWluxop

SUNWcfpl

SUNWcfplr

SUNWjss

SUNWcpcu

SUNWcqhpc

SUNWkey

SUNWeuodf

SUNWless

SUNWcstl

SUNWlibsasl

SUNWlldap

SUNWlsimega

SUNWmdb

SUNWmdbdm

SUNWmdbr

SUNWdtrc

SUNWdtrp

SUNWfctl

SUNWemlxs

SUNWemlxu

SUNWmibii

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-30

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

SUNWsasnm

SUNWsadmi

SUNWsacom

SUNWmipr

SUNWmipu

SUNWmkcd

SUNWfchbar

SUNWfchba

SUNWfcip

SUNWfcmdb

SUNWfcp

SUNWfcprt

SUNWfcsm

SUNWfmd

SUNWfss

SUNWnge

SUNWpkgcmdsr

SUNWpkgcmdsu

SUNWpsdcr

SUNWsolnm

SUNWpsdir

SUNWqlc

SUNWqos

SUNWqosu

SUNWrmodu

SUNWroute

SUNWrpcib

SUNWrsgk

SUNWrtls

SUNWspnego

Customizing system files

-Mount points table (/etc/vfstab) fd- /dev/fdfd-no- /proc-/procproc-no- /dev/dsk/c1t0d0s3--swap-no-

/dev/dsk/c1t0d0s0/dev/rdsk/c1t0d0s0/ufs1no- /dev/dsk/c1t0d0s1/dev/rdsk/c1t0d0s1/varufs1no- /dev/dsk/c1t0d0s5/dev/rdsk/c1t0d0s5/optufs2yes- /devices-/devicesdevfs-no-

ctfs- /system/contractctfs-no-objfs-/system/objectobjfs-no-swap- /tmptmpfs-yes -

-Network host addresses (/etc/hosts)

-Network host addresses (/etc/hosts)

-Environment variables (/etc/default/init)

Cleaning devices

Customizing system devices

-Physical devices (/devices)

-Logical devices (/dev)

Installing boot information

-Updating boot environment configuration file

-Installing boot blocks (c1t0d0)

Executing profile begin script...

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-31

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Completed profile begin script.

Processing profile

-Selecting cluster (SUNWCreq)

-Deselecting cluster (SUNWCudf)

-Deselecting cluster (SUNWCbs)

-Deselecting cluster (SUNWCnfss)

-Deselecting cluster (SUNWCsndm)

-Deselecting cluster (SUNWCpcmc)

-Deselecting cluster (SUNWCpicl)

-Selecting cluster (SUNWCacc)

-Selecting cluster (SUNWCssh)

-Selecting cluster (SUNWCpool)

-Selecting cluster (SUNWCvld)

-Selecting cluster (SUNWCfwshl)

-Selecting cluster (SUNWClu)

-Selecting cluster (SUNWCcpc)

-Selecting cluster (SUNWCsea)

-Selecting cluster (SUNWCstl)

-Selecting cluster (SUNWCmip)

-Selecting cluster (SUNWCqos)

-Selecting cluster (SUNWCzone)

-Selecting cluster (SUNWCzebra)

-Deselecting package (SUNWauda)

-Deselecting package (SUNWad810)

-Deselecting package (SUNWvia823x)

-Deselecting package (SUNWcnsu)

-Deselecting package (SUNWtnamd)

-Deselecting package (SUNWtnamr)

-Deselecting package (SUNWrcmdr)

-Deselecting package (SUNWrcmds)

-Deselecting package (SUNWtftp)

-Deselecting package (SUNWtftpr)

-Deselecting package (SUNWcnsr)

-Deselecting package (SUNWatfsr)

-Deselecting package (SUNWatfsu)

-Deselecting package (SUNWftpr)

-Deselecting package (SUNWftpu)

-Deselecting package (SUNWipmi)

-Deselecting package (SUNWxsvc)

-Deselecting package (SUNWflexruntime)

-Deselecting package (SUNWxwmod)

-Selecting package (SUNWadmc)

-Selecting package (SUNWadmfr)

-Selecting package (SUNWadmfw)

-Selecting package (SUNWdtdmr)

-Selecting package (SUNWxwfnt)

-Selecting package (SUNWzip)

-Selecting package (SUNWless)

-Selecting package (SUNWeurf)

-Selecting package (SUNWj5rt)

-Selecting package (SUNWxwacx)

-Selecting package (SUNWxwice)

-Selecting package (SUNWxwplr)

-Selecting package (SUNWxwrtl)

-Selecting package (SUNWxwplt)

-Selecting package (SUNWxi18n)

-Selecting package (SUNWtltk)

-Selecting package (SUNWeuodf)

-Selecting package (SUNWocf)

-Selecting package (SUNWocfr)

-Selecting package (SUNWbtool)

-Selecting package (SUNWsprot)

-Selecting package (SUNWmdbdm)

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-32

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

-Selecting package (SUNWmkcd)

-Selecting package (SUNWspnego)

-Selecting package (SUNWtnfc)

-Selecting package (SUNWtnfd)

-Selecting package (SUNWbind)

-Selecting package (SUNWbindr)

-Selecting package (SUNWctpls)

-Selecting package (SUNWfss)

-Selecting package (SUNWgcmn)

-Selecting package (SUNWgssdh)

-Selecting package (SUNWgssk)

-Selecting package (SUNWinst)

-Selecting package (SUNWi15rf)

-Selecting package (SUNWipc)

-Selecting package (SUNWmdbr)

-Selecting package (SUNWmfrun)

-Selecting package (SUNWrsg)

-Selecting package (SUNWrsgk)

-Selecting package (SUNWter)

-Selecting package (SUNWtoo)

-Selecting package (SUNW1394)

-Selecting all disks

-Configuring boot device

-Using disk (c1t0d0) for "rootdisk"

-Deleting Solaris fdisk partition (c1t0d0)

-Deleting Solaris fdisk partition (c1t1d0)

-Creating "all" Solaris fdisk partition (c1t0d0)

-Creating "all" Solaris fdisk partition (c1t1d0)

-Configuring / (c1t0d0s0)

-Configuring /var (c1t0d0s1)

-Configuring swap (c1t0d0s3)

-

Configuring

(c1t0d0s4)

-

Configuring

(c1t0d0s6)

-Configuring /opt (c1t0d0s5)

-Deselecting unmodified disk (c1t1d0)

Verifying disk configuration

Verifying space allocation

- Total software size: 420.10 Mbytes

You may need to eject the CD or select a different boot device after reboot to avoid repeating the installation process.

Configuring disk (c1t0d0)

- Creating Fdisk partition table

Fdisk partition table for disk c1t0d0 (input file for fdisk(1M))

type: 130

active:

128

offset: 16065

size: 143347995

type: 100

active:

0

offset: 0

size: 0

type:

100

active:

0

offset:

0

size:

0

type:

100

active:

0

offset:

0

size:

0

- Creating Solaris disk label (VTOC)

Creating and checking UFS file systems - Creating / (c1t0d0s0)

Warning: 1474 sector(s) in last cylinder unallocated /dev/rdsk/c1t0d0s0:4096574 sectors in 667 cylinders of 48 tracks, 128 sectors

 

2000.3MB in 42 cyl groups (16 c/g, 48.00MB/g, 11648 i/g)

 

 

 

 

 

 

 

super-block

backups

(for fsck -Fufs-ob=#) at:

 

 

 

 

 

 

 

32,

98464,

196896,

295328,

393760,

492192,

590624,

689056,

787488,

885920,

 

 

 

 

 

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

 

 

OL-18083-01

 

 

 

 

 

 

 

 

 

 

2-33

 

 

 

 

 

 

 

 

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

3149856, 3248288, 3346720, 3445152, 3543584, 3642016, 3740448, 3838880, 3937312, 4035744

- Creating /var (c1t0d0s1)

Warning: 4866 sector(s) in last cylinder unallocated /dev/rdsk/c1t0d0s1:10249470 sectors in 1669 cylinders of 48 tracks, 128 sectors

5004.6MB in 105 cyl groups (16 c/g, 48.00MB/g, 5824 i/g) super-blockbackups (for fsck-Fufs-ob=#) at:

32, 98464, 196896, 295328, 393760, 492192, 590624, 689056, 787488, 885920, 9342880, 9441312, 9539744, 9638176, 9736608, 9835040, 9933472, 10031904, 10130336, 10228768

- Creating /opt (c1t0d0s5)

Warning: 1062 sector(s) in last cylinder unallocated

/dev/rdsk/c1t0d0s5:116599770 sectors in 18978 cylinders of 48 tracks, 128 sectors 56933.5MB in 1187 cyl groups (16 c/g, 48.00MB/g, 5824 i/g)

super-blockbackups (for fsck-Fufs-ob=#) at:

32, 98464, 196896, 295328, 393760, 492192, 590624, 689056, 787488, 885920, Initializing cylinder groups:

.......................

super-blockbackups for last 10 cylinder groups at:

115707040, 115805472, 115903904, 116002336, 116100768, 116199200, 116297632, 116396064, 116494496, 116592928

Beginning Solaris software installation 23303 blocks

Installation of <SUNWcsu> was successful. 5043 blocks

Installation of <SUNWcsr> was successful. 21985 blocks

Installation of <SUNWcsl> was successful. 75 blocks

Installation of <SUNWcnetr> was successful. 43978 blocks

 

 

 

Installation of <SUNWckr> was successful.

 

 

 

30 blocks

 

 

 

Installation of <SUNWkvm> was successful.

 

 

 

Installation of <SUNWcar> was successful.

 

 

 

Installation of <SUNWcakr> was successful.

 

 

 

7 blocks

 

 

 

add c devices/pseudo/arp@0:arp (44, 0) 0666 root sys

 

 

 

add link /dev/arp=../devices/pseudo/arp@0:arp

 

 

 

add c devices/pseudo/clone@0:ibd (11, 170) 0666 root sys

 

 

 

add link /dev/ibd=../devices/pseudo/clone@0:ibd

 

 

 

add c devices/pseudo/icmp@0:icmp (5, 0) 0666 root sys

 

 

 

add link /dev/icmp=../devices/pseudo/icmp@0:icmp

 

 

 

add c devices/pseudo/icmp@0:icmp (5, 0) 0666 root sys

 

 

 

add link /dev/rawip=../devices/pseudo/icmp@0:icmp

 

 

 

add c devices/pseudo/icmp6@0:icmp6 (140, 1) 0666 root sys

 

 

 

add link /dev/icmp6=../devices/pseudo/icmp6@0:icmp6

 

 

 

add c devices/pseudo/icmp6@0:icmp6 (140, 1) 0666 root sys

 

 

 

add link /dev/rawip6=../devices/pseudo/icmp6@0:icmp6

 

 

 

add c devices/pseudo/ip@0:ip (3, 0) 0666 root sys

 

 

 

add link /dev/ip=../devices/pseudo/ip@0:ip

 

 

 

add c devices/pseudo/ip6@0:ip6 (139, 1) 0666 root sys

 

 

 

add link /dev/ip6=../devices/pseudo/ip6@0:ip6

 

 

 

add c devices/pseudo/rts@0:rts (43, 0) 0666 root sys

 

 

 

add link /dev/rts=../devices/pseudo/rts@0:rts

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

2-34

 

OL-18083-01

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

add c devices/pseudo/tcp@0:tcp (42, 2) 0666 root sys add link /dev/tcp=../devices/pseudo/tcp@0:tcp

add c devices/pseudo/tcp6@0:tcp6 (142, 3) 0666 root sys add link /dev/tcp6=../devices/pseudo/tcp6@0:tcp6

add c devices/pseudo/udp@0:udp (41, 0) 0666 root sys add link /dev/udp=../devices/pseudo/udp@0:udp

add c devices/pseudo/udp6@0:udp6 (141, 1) 0666 root sys add link /dev/udp6=../devices/pseudo/udp6@0:udp6

add c devices/pseudo/ipsecah@0:ipsecah (137, 1) 0666 root sys add link /dev/ipsecah=../devices/pseudo/ipsecah@0:ipsecah

add c devices/pseudo/ipsecesp@0:ipsecesp (138, 1) 0666 root sys add link /dev/ipsecesp=../devices/pseudo/ipsecesp@0:ipsecesp add c devices/pseudo/keysock@0:keysock (136, 0) 0666 root sys add link /dev/keysock=../devices/pseudo/keysock@0:keysock

add c devices/pseudo/cn@0:console (0, 0) 0620 root tty add link /dev/console=../devices/pseudo/cn@0:console add c devices/pseudo/cn@0:syscon (0, 0) 0620 root tty add link /dev/syscon=../devices/pseudo/cn@0:syscon

add c devices/pseudo/cn@0:systty (0, 0) 0620 root tty add link /dev/systty=../devices/pseudo/cn@0:systty

add c devices/pseudo/devinfo@0:devinfo (88, 0) 0640 root sys add c devices/pseudo/ksyms@0:ksyms (72, 0) 0666 root sys add link /dev/ksyms=../devices/pseudo/ksyms@0:ksyms

add c devices/pseudo/log@0:conslog (21, 0) 0666 root sys add link /dev/conslog=../devices/pseudo/log@0:conslog add c devices/pseudo/log@0:log (21, 5) 0640 root sys

add link /dev/log=../devices/pseudo/log@0:log

add c devices/pseudo/mm@0:mem (13, 0) 0640 root sys add link /dev/mem=../devices/pseudo/mm@0:mem

add c devices/pseudo/mm@0:kmem (13, 1) 0640 root sys add link /dev/kmem=../devices/pseudo/mm@0:kmem

add c devices/pseudo/mm@0:null (13, 2) 0666 root sys add link /dev/null=../devices/pseudo/mm@0:null

add c devices/pseudo/mm@0:allkmem (13, 3) 0600 root sys add link /dev/allkmem=../devices/pseudo/mm@0:allkmem add c devices/pseudo/mm@0:zero (13, 12) 0666 root sys add link /dev/zero=../devices/pseudo/mm@0:zero

add c devices/pseudo/openeepr@0:openprom (6, 0) 0640 root sys add link /dev/openprom=../devices/pseudo/openeepr@0:openprom add c devices/pseudo/sad@0:admin (12, 1) 0666 root sys

add link /dev/sad/admin=../../devices/pseudo/sad@0:admin add c devices/pseudo/sad@0:user (12, 0) 0666 root sys add link /dev/sad/user=../../devices/pseudo/sad@0:user add c devices/pseudo/sy@0:tty (22, 0) 0666 root tty

add link /dev/tty=../devices/pseudo/sy@0:tty

add c devices/pseudo/sysevent@0:sysevent (152, 0) 0600 root sys add link /dev/sysevent=../devices/pseudo/sysevent@0:sysevent add c devices/pseudo/sysmsg@0:msglog (97, 1) 0600 root sys

add link /dev/msglog=../devices/pseudo/sysmsg@0:msglog

add c devices/pseudo/sysmsg@0:sysmsg (97, 0) 0600 root sys add link /dev/sysmsg=../devices/pseudo/sysmsg@0:sysmsg

add c devices/pseudo/tl@0:ticots (105, 0) 0666 root sys add link /dev/ticots=../devices/pseudo/tl@0:ticots

add c devices/pseudo/tl@0:ticotsord (105, 1) 0666 root sys add link /dev/ticotsord=../devices/pseudo/tl@0:ticotsord add c devices/pseudo/tl@0:ticlts (105, 2) 0666 root sys add link /dev/ticlts=../devices/pseudo/tl@0:ticlts

add c devices/pseudo/wc@0:wscons (15, 0) 0600 root sys add link /dev/wscons=../devices/pseudo/wc@0:wscons

add c devices/pseudo/conskbd@0:kbd (103, 0) 0666 root sys add link /dev/kbd=../devices/pseudo/conskbd@0:kbd

Installation of <SUNWcsd> was successful. 422 blocks

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-35

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Installation of <SUNWzlib> was successful. 3826 blocks

Installation of <SUNWlibmsr> was successful.

Installation of <SUNWlibms> was successful. 5495 blocks

Installation of <SUNWlxml> was successful.

Installation of <SUNWxwrtl> was successful.

Installation of <SUNWbzip> was successful. 22155 blocks

Installation of <SUNWxwfnt> was successful. 440 blocks

Installation of <SUNWxwice> was successful. 63 blocks

Installation of <SUNWxwdv> was successful. 3 blocks

Installation of <SUNWxwplr> was successful. 8688 blocks

Installation of <SUNWperl584core> was successful. 39013 blocks

Installation of <SUNWperl584usr> was successful. 3641 blocks

Installation of <SUNWesu> was successful. 118 blocks

Installation of <SUNWcpp> was successful.

Installation of <SUNWdtcor> was successful. 31656 blocks

Installation of <SUNWxwplt> was successful. 1019 blocks

Installation of <SUNWlexpt> was successful.

Installation of <SUNWgcmn> was successful. 116 blocks

Installation of <SUNWctpls> was successful. 18841 blocks

Installation of <SUNWmfrun> was successful. 260 blocks

Installation of <SUNWxwacx> was successful. 3 blocks

Installation of <SUNWsshdr> was successful. 390 blocks

Installation of <SUNWadmlib-sysid>was successful. 27 blocks

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-36

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Installation of <SUNWadmr> was successful. 3755 blocks

Installation of <SUNWadmap> was successful.

Installation of <SUNWgssc> was successful. 554 blocks

Installation of <SUNWgss> was successful. 11613 blocks

Installation of <SUNWopenssl-libraries>was successful. 687 blocks

Installation of <SUNWsshcu> was successful. 694 blocks

Installation of <SUNWsshdu> was successful.

Installation of <SUNWdtdmr> was successful. 6063 blocks

Installation of <SUNWtltk> was successful. 134 blocks

Installation of <SUNWgzip> was successful. 173 blocks

Installation of <SUNWsshr> was successful. 970 blocks

Installation of <SUNWsshu> was successful. 11214 blocks

Installation of <SUNWlibC> was successful. 151975 blocks

Installation of <SUNWj5rt> was successful. 580 blocks

Installation of <SUNWwbsup> was successful.

Installation of <SUNWinstall-patch-utils-root>was successful.

Installation of <SUNWswmt> was successful. 5206 blocks

Installation of <SUNWmdr> was successful. 1139 blocks

Installation of <SUNWmdu> was successful. 2937 blocks

Installation of <SUNWadmc> was successful. 4275 blocks

Installation of <SUNWnfsckr> was successful. 89 blocks

Installation of <SUNWnfscr> was successful. 426 blocks

Installation of <SUNWnfscu> was successful.

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-37

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

8 blocks

Installation of <SUNWkrbr> was successful. 3840 blocks

Installation of <SUNWkrbu> was successful. 259 blocks

Installation of <SUNWbip> was successful. 237 blocks

Installation of <SUNWtnetc> was successful. 1498 blocks

Installation of <SUNWrcmdc> was successful. 4857 blocks

Reboot client to install driver.

Installation of <SUNWib> was successful. 2431 blocks

Reboot client to install driver.

Installation of <SUNWtavor> was successful. 599 blocks

Installation of <SUNWtcsh> was successful. 1085 blocks

Installation of <SUNWtecla> was successful. 1978 blocks

Installation of <SUNWter> was successful. 1975 blocks

Installation of <SUNWpr> was successful. 10669 blocks

Installation of <SUNWtls> was successful. 90 blocks

Installation of <SUNWtnetd> was successful.

Installation of <SUNWtnetr> was successful. 1039 blocks

Installation of <SUNWtnfc> was successful. 97 blocks

Installation of <SUNWtnfd> was successful. 1784 blocks

Installation of <SUNWtoo> was successful.

Installation of <SUNWucbt> was successful.

Installation of <SUNWudaplr> was successful. 382 blocks

Installation of <SUNWudaplu> was successful. 256 blocks

Installation of <SUNWipoib> was successful. 680 blocks

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-38

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

 

 

Installation of <SUNWudapltu> was successful.

 

 

559 blocks

 

 

Reboot client to install driver.

 

 

Installation of <SUNWudapltr> was successful.

 

 

Installation of <SUNWocfr> was successful.

 

 

974 blocks

 

 

Installation of <SUNWocf> was successful.

 

 

1580 blocks

 

 

Reboot client to install driver.

 

 

Reboot client to install driver.

 

 

Reboot client to install driver.

 

 

Reboot client to install driver.

 

 

Reboot client to install driver.

 

 

Reboot client to install driver.

 

 

Reboot client to install driver.

 

 

Reboot client to install driver.

 

 

Reboot client to install driver.

 

 

Removing empty OWconfig

 

 

Installation of <SUNWos86r> was successful.

 

 

Installation of <SUNWrmodr> was successful.

 

 

Reboot client to install driver.

 

 

Installation of <CADP160> was successful.

 

 

1069 blocks

 

 

Reboot client to install driver.

 

 

Installation of <SUNWaudd> was successful.

 

 

3863 blocks

 

 

Reboot client to install driver.

 

 

Reboot client to install driver.

 

 

Reboot client to install driver.

 

 

Reboot client to install driver.

 

 

Reboot client to install driver.

 

 

Reboot client to install driver.

 

 

Reboot client to install driver.

 

 

Reboot client to install driver.

 

 

Reboot client to install driver.

 

 

Reboot client to install driver.

 

 

Installation of <SUNWusb> was successful.

 

 

138 blocks

 

 

Installation of <SUNWusbs> was successful.

 

 

465 blocks

 

 

Reboot client to install driver.

 

 

Installation of <SUNWuedg> was successful.

 

 

732 blocks

 

 

Modifying /a/kernel/drv/sd.conf

 

 

Reboot client to install driver.

 

 

Installation of <HPFC> was successful.

 

 

66 blocks

 

 

Installation of <NCRos86r> was successful.

 

 

151 blocks

 

 

Reboot client to install driver.

 

 

Installation of <SUNWugen> was successful.

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-39

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

 

 

 

379 blocks

 

 

 

Reboot client to install driver.

 

 

 

Installation of <SK98sol> was successful.

 

 

 

679 blocks

 

 

 

Reboot client to install driver.

 

 

 

Installation of <SKfp> was successful.

 

 

 

8309 blocks

 

 

 

Installation of <SUNWeurf> was successful.

 

 

 

2429 blocks

 

 

 

Reboot client to install driver.

 

 

 

Installation of <SUNW1394> was successful.

 

 

 

1423 blocks

 

 

 

Installation of <SUNWxi18n> was successful.

 

 

 

95 blocks

 

 

 

Installation of <SUNWvld> was successful.

 

 

 

40 blocks

 

 

 

Installation of <SUNWvldu> was successful.

 

 

 

1198 blocks

 

 

 

Installation of <SUNWbash> was successful.

 

 

 

Installation of <SUNWproduct-registry-root>was successful.

 

 

 

817 blocks

 

 

 

registry conversion not required

 

 

 

Installation of <SUNWwsr2> was successful.

 

 

 

158 blocks

 

 

 

Reboot client to install driver.

 

 

 

Installation of <SUNWaac> was successful.

 

 

 

3 blocks

 

 

 

Installation of <SUNWaccr> was successful.

 

 

 

511 blocks

 

 

 

Installation of <SUNWaccu> was successful.

 

 

 

Installation of <SUNWgrub> was successful.

 

 

 

Installation of <SUNWadmfr> was successful.

 

 

 

1167 blocks

 

 

 

Installation of <SUNWadmfw> was successful.

 

 

 

80 blocks

 

 

 

Installation of <SUNWi15rf> was successful.

 

 

 

Reboot client to install driver.

 

 

 

Installation of <SUNWadp> was successful.

 

 

 

Installation of <SUNWradpu320> was successful.

 

 

 

1216 blocks

 

 

 

Reboot client to install driver.

 

 

 

Installation of <SUNWadpu320> was successful.

 

 

 

136 blocks

 

 

 

Reboot client to install driver.

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

2-40

 

OL-18083-01

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Installation of <SUNWamr> was successful. 2519 blocks

Installation of <SUNWsprot> was successful. 190 blocks

Installation of <SUNWrsg> was successful. 453 blocks

Installation of <SUNWgssdh> was successful. 671 blocks

Installation of <SUNWgssk> was successful. 1251 blocks

Reboot client to install driver.

Installation of <SUNWxge> was successful. 2194 blocks

Installation of <SUNWbtool> was successful. 24616 blocks

Installation of <SUNWcslr> was successful. 1022 blocks

Installation of <SUNWidnl> was successful. 1830 blocks

Installation of <SUNWinst> was successful. 596 blocks

Reboot client to install driver.

Installation of <SUNWintgige> was successful. 41 blocks

Installation of <SUNWipc> was successful. 119 blocks

Installation of <SUNWipfr> was successful. 3499 blocks

Installation of <SUNWipfu> was successful. 6407 blocks

/a/etc/lu/synclist Installing /a/etc/default/lu

Installation of <SUNWlur> was successful. 3495 blocks

Installation of <SUNWluu> was successful.

Reboot client to install driver.

Installation of <SUNWiscsir> was successful.

Installation of <SUNWiscsiu> was successful. 790 blocks

Installation of <SUNWloc> was successful. 83 blocks

Installation of <SUNWnisr> was successful. 3891 blocks

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-41

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Installation of <SUNWnisu> was successful. 45 blocks

Installation of <SUNWzebrar> was successful. 4056 blocks

Installation of <SUNWzebrau> was successful. 267 blocks

Installation of <SUNWzip> was successful. 9 blocks

Installation of <SUNWzoner> was successful. 606 blocks

Installation of <SUNWluzone> was successful.

Installation of <SUNWpoolr> was successful. 1366 blocks

Installation of <SUNWpool> was successful. 878 blocks

Installation of <SUNWzoneu> was successful. 4985 blocks

Installation of <SUNWzsh> was successful.

Reboot client to install driver.

Installation of <SYMhisl> was successful. 72 blocks

Installation of <SUNWcpc> was successful.

Installation of <SUNWbindr> was successful. 4546 blocks

Installation of <SUNWbind> was successful.

Installation of <SUNWbipr> was successful.

Reboot client to install driver.

Installation of <SUNWcadp> was successful. 955 blocks

Reboot client to install driver.

Installation of <SUNWced> was successful. 161 blocks

Installation of <SUNWcfcl> was successful.

Installation of <SUNWcfclr> was successful. 253 blocks

Installation of <SUNWluxop> was successful. 594 blocks

Installation of <SUNWcfpl> was successful. 2 blocks

Installation of <SUNWcfplr> was successful. 3979 blocks

Installation of <SUNWjss> was successful.

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-42

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

918 blocks

Installation of <SUNWcpcu> was successful. 29 blocks

Reboot client to install driver.

Installation of <SUNWcqhpc> was successful. 215 blocks

Installation of <SUNWkey> was successful. 128 blocks

Installation of <SUNWeuodf> was successful. 231 blocks

Installation of <SUNWless> was successful. 184 blocks

Installation of <SUNWcstl> was successful. 928 blocks

Installation of <SUNWlibsasl> was successful. 314 blocks

Installation of <SUNWlldap> was successful. 228 blocks

Reboot client to install driver.

Installation of <SUNWlsimega> was successful. 10159 blocks

Installation of <SUNWmdb> was successful. 29 blocks

Installation of <SUNWmdbdm> was successful. 6853 blocks

Installation of <SUNWmdbr> was successful. 3972 blocks

Installation of <SUNWdtrc> was successful. 1313 blocks

Installation of <SUNWdtrp> was successful. 1227 blocks

Reboot client to install driver.

Installation of <SUNWfctl> was successful. 3552 blocks

Reboot client to install driver.

Installation of <SUNWemlxs> was successful. 2568 blocks

Installation of <SUNWemlxu> was successful. 174 blocks

Installation of <SUNWmibii> was successful. 1332 blocks

Installation of <SUNWsasnm> was successful. 1106 blocks

Installation of <SUNWsadmi> was successful.

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-43

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

328 blocks

Installation of <SUNWsacom> was successful. 40 blocks

Installation of <SUNWmipr> was successful. 468 blocks

Installation of <SUNWmipu> was successful. 844 blocks

Installation of <SUNWmkcd> was successful.

Modifying /a/etc/hba.conf

Installation of <SUNWfchbar> was successful. 3366 blocks

Installation of <SUNWfchba> was successful. 537 blocks

Reboot client to install driver.

Installation of <SUNWfcip> was successful. 312 blocks

Installation of <SUNWfcmdb> was successful. 803 blocks

Reboot client to install driver.

Installation of <SUNWfcp> was successful. 79 blocks

Installation of <SUNWfcprt> was successful. 361 blocks

Reboot client to install driver.

Installation of <SUNWfcsm> was successful. 3020 blocks

Installation of <SUNWfmd> was successful. 197 blocks

Installation of <SUNWfss> was successful. 275 blocks

Reboot client to install driver.

Installation of <SUNWnge> was successful. 1 blocks

Installation of <SUNWpkgcmdsr> was successful. 4530 blocks

Installation of <SUNWpkgcmdsu> was successful. 1509 blocks

Reboot client to install driver.

Installation of <SUNWpsdcr> was successful.

 

 

 

Installation of <SUNWsolnm> was successful.

 

 

 

590 blocks

 

 

 

Reboot client to install driver.

 

 

 

Installation of <SUNWpsdir> was successful.

 

 

 

3866 blocks

 

 

 

Reboot client to install driver.

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

2-44

 

OL-18083-01

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Installation of <SUNWqlc> was successful. 387 blocks

Installation of <SUNWqos> was successful. 136 blocks

Installation of <SUNWqosu> was successful. 2 blocks

Installation of <SUNWrmodu> was successful. 497 blocks

Installation of <SUNWroute> was successful. 271 blocks

Reboot client to install driver.

Installation of <SUNWrpcib> was successful. 145 blocks

Installation of <SUNWrsgk> was successful. 89 blocks

Reboot client to install driver.

Installation of <SUNWrtls> was successful. 125 blocks

Installation of <SUNWspnego> was successful.

Solaris 10 software installation succeeded

Solaris 10 packages fully installed

SUNWcsu

SUNWcsr

SUNWcsl

SUNWcnetr

SUNWckr

SUNWkvm

SUNWcar

SUNWcakr

SUNWcsd

SUNWzlib

SUNWlibmsr

SUNWlibms

SUNWlxml

SUNWxwrtl

SUNWbzip

SUNWxwfnt

SUNWxwice

SUNWxwdv

SUNWxwplr

SUNWperl584core

SUNWperl584usr

SUNWesu

SUNWcpp

SUNWdtcor

SUNWxwplt

SUNWlexpt

SUNWgcmn

SUNWctpls

SUNWmfrun

SUNWxwacx

SUNWsshdr

SUNWadmlib-sysid

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-45

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

SUNWadmr

SUNWadmap

SUNWgssc

SUNWgss

SUNWopenssl-libraries

SUNWsshcu

SUNWsshdu

SUNWdtdmr

SUNWtltk

SUNWgzip

SUNWsshr

SUNWsshu

SUNWlibC

SUNWj5rt

SUNWwbsup

SUNWinstall-patch-utils-root

SUNWswmt

SUNWmdr

SUNWmdu

SUNWadmc

SUNWnfsckr

SUNWnfscr

SUNWnfscu

SUNWkrbr

SUNWkrbu

SUNWbip

SUNWtnetc

SUNWrcmdc

SUNWib

SUNWtavor

SUNWtcsh

SUNWtecla

SUNWter

SUNWpr

SUNWtls

SUNWtnetd

SUNWtnetr

SUNWtnfc

SUNWtnfd

SUNWtoo

SUNWucbt

SUNWudaplr

SUNWudaplu

SUNWipoib

SUNWudapltu

SUNWudapltr

SUNWocfr

SUNWocf

SUNWos86r

SUNWrmodr

CADP160

SUNWaudd

SUNWusb

SUNWusbs

SUNWuedg

HPFC

NCRos86r

SUNWugen

SK98sol

SKfp

SUNWeurf

SUNW1394

SUNWxi18n

SUNWvld

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-46

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

SUNWvldu

SUNWbash

SUNWproduct-registry-root

SUNWwsr2

SUNWaac

SUNWaccr

SUNWaccu

SUNWgrub

SUNWadmfr

SUNWadmfw

SUNWi15rf

SUNWadp

SUNWradpu320

SUNWadpu320

SUNWamr

SUNWsprot

SUNWrsg

SUNWgssdh

SUNWgssk

SUNWxge

SUNWbtool

SUNWcslr

SUNWidnl

SUNWinst

SUNWintgige

SUNWipc

SUNWipfr

SUNWipfu

SUNWlur

SUNWluu

SUNWiscsir

SUNWiscsiu

SUNWloc

SUNWnisr

SUNWnisu

SUNWzebrar

SUNWzebrau

SUNWzip

SUNWzoner

SUNWluzone

SUNWpoolr

SUNWpool

SUNWzoneu

SUNWzsh

SYMhisl

SUNWcpc

SUNWbindr

SUNWbind

SUNWbipr

SUNWcadp

SUNWced

SUNWcfcl

SUNWcfclr

SUNWluxop

SUNWcfpl

SUNWcfplr

SUNWjss

SUNWcpcu

SUNWcqhpc

SUNWkey

SUNWeuodf

SUNWless

SUNWcstl

SUNWlibsasl

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-47

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

SUNWlldap

SUNWlsimega

SUNWmdb

SUNWmdbdm

SUNWmdbr

SUNWdtrc

SUNWdtrp

SUNWfctl

SUNWemlxs

SUNWemlxu

SUNWmibii

SUNWsasnm

SUNWsadmi

SUNWsacom

SUNWmipr

SUNWmipu

SUNWmkcd

SUNWfchbar

SUNWfchba

SUNWfcip

SUNWfcmdb

SUNWfcp

SUNWfcprt

SUNWfcsm

SUNWfmd

SUNWfss

SUNWnge

SUNWpkgcmdsr

SUNWpkgcmdsu

SUNWpsdcr

SUNWsolnm

SUNWpsdir

SUNWqlc

SUNWqos

SUNWqosu

SUNWrmodu

SUNWroute

SUNWrpcib

SUNWrsgk

SUNWrtls

SUNWspnego

Customizing system files

-Mount points table (/etc/vfstab) fd- /dev/fdfd-no- /proc-/procproc-no- /dev/dsk/c1t0d0s3--swap-no-

/dev/dsk/c1t0d0s0/dev/rdsk/c1t0d0s0/ufs1no- /dev/dsk/c1t0d0s1/dev/rdsk/c1t0d0s1/varufs1no- /dev/dsk/c1t0d0s5/dev/rdsk/c1t0d0s5/optufs2yes- /devices-/devicesdevfs-no-

ctfs- /system/contractctfs-no-objfs-/system/objectobjfs-no-swap- /tmptmpfs-yes -

-Network host addresses (/etc/hosts)

-Network host addresses (/etc/hosts)

-Environment variables (/etc/default/init)

Cleaning devices

Customizing system devices

-Physical devices (/devices)

-Logical devices (/dev)

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-48

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Installing boot information

-Updating boot environment configuration file

-Installing boot blocks (c1t0d0)

Installation complete

Executing SolStart postinstall phase...

Executing finish script "patch_finish"...

Finish script patch_finish execution completed. Executing JumpStart postinstall phase...

all finished

Finish script any_finish execution completed.

The begin script log 'begin.log'

is located in /var/sadm/system/logs after reboot.

The finish script log 'finish.log'

is located in /var/sadm/system/logs after reboot.

Note You may be prompted during the reboot to enterCtrl-B orCtrl-C to open configuration tools for your hardware. You do not need to open any of these tools to complete this installation.

Caution The CD is automatically ejected from theCD-ROMdrive prior to rebooting to ensure that the host is rebooted from the newly installed operating system. Do not reinsert the CD into theCD-ROMdrive at this time.

syncing file systems... done

rebooting...

Resetting ...

Note You can select your terminal type from the picklist or the default terminal type (from the serial port). Cisco recommends that you use the default terminal while you are installing software.

screen not found.

Can't open input device.

Keyboard not present. Using ttya for input and output.

SunFire V40z, No Keyboard

OpenBoot 3.23, 4096 MB memory installed, Serial #12797485.

Ethernet address 8:0:20:c3:46:2d, Host ID: 80c3462d.

Rebooting with command: boot

Boot device: /pci@1f,4000/scsi@3/disk@0,0:a File and args:

 

 

SunOS Release 5.10 Version Generic 64-bit

 

 

Copyright 1983-2005Sun Microsystems, Inc. All rights reserved.

 

 

Use is subject to license terms.

 

 

Hostname: va-host

 

 

Configuring devices.

 

 

Loading smf(5) service descriptions: 67/67

 

 

checking ufs filesystems

 

 

/dev/rdsk/c0t0d0s5: is logging.

 

 

Creating new rsa public/private host key pair

 

 

Creating new dsa public/private host key pair

 

 

Configuring network interface addresses: ce0 hme0 hme1

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-49

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

This system is configured with NFS version 4, which uses a domain name that is automatically derived from the system's name services. The derived domain name is sufficient for most configurations. In a few cases, mounts that cross different domains might cause files to be owned by "nobody" due to the lack of a common domain name.

Do you need to override the system's default NFS version 4 domain name (yes/no) ? [no] :

Step 7 Enterno to continue the reconfiguration process and pressEnter.

The system displays information similar to the following:

For more information about how the NFS version 4 default domain name is derived and its impact, refer to the man pages for nfs(4) and nfsmapid(1m), and the System Administration Guide: Network Services.

vtghost console login:

This completes the installation of the Sun Solaris 10 operating system. Proceed to the “Configuring Your Host” section on page 2-50.

Configuring Your Host

Step 1

If you are already logged in to your host platform, proceed to Step 2. Otherwise log in as root and use

 

the default password, vtghost. The system displays something similar to the following:

 

Sep 8 01:15:08 vtghost

login: ROOT LOGIN /dev/console

 

Sun Microsystems Inc.

SunOS 5.10

Generic January 2005.

 

#

 

 

Step 2

Reconfigure the system by entering the sys-unconfig command and pressingEnter.

A screen similar to the following is displayed:

WARNING

This program will unconfigure your system. It will cause it

to revert to a "blank" system - it will not have a name or know about other systems or networks.

This program will also halt the system.

Do you want to continue (y/n) ?

Step 3 Entery to continue the reconfiguration process and pressEnter.

The system displays information similar to the following:

svc.startd: The system is coming down. Please wait. svc.startd: 57 system services are now being stopped.

Sep 8 01:22:21 vtghost rpcbind: rpcbind terminating on signal.

svc.startd: The system is down. syncing file systems... done Program terminated

{1} ok

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-50

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Step 4 Reboot your system using the method identified for your platform type:

Sparc-basedplatforms—Entertheboot command and pressEnter to reboot the system.

Opteron-basedplatforms—Pressany key to reboot the system.

Note If you are installing Solaris 10 on anOpteron-basedplatform, you might be prompted during the reboot to enterCtrl-B orCtrl-C to open configuration tools for your hardware. You do not need to open any of these tools to complete this installation.

The system displays information similar to the following:

SC Alert: Host System has Reset

Probing system devices

Probing memory

Probing I/O buses

Sun Fire V210, No Keyboard

Copyright 2005 Sun Microsystems, Inc. All rights reserved.

OpenBoot 4.18.5, 2048 MB memory installed, Serial #52030991.

Ethernet address 0:3:ba:19:ee:f, Host ID: 8319ee0f.

Initializing

1MB of memory at addr

103feec000

Initializing

1MB of memory at addr

103fee0000

Initializing

15MB of memory at addr

103f002000

Initializing

16MB of memory at addr

103e002000

Initializing

992MB of memory at addr

1000000000

Initializing

1024MB of memory at addr

0

Rebooting with command: boot

Boot device: /pci@1c,600000/scsi@2/disk@0,0:a File and args: SunOS Release 5.10 Version Generic_118833-1764-bit

Copyright 1983-2005Sun Microsystems, Inc. All rights reserved. Use is subject to license terms.

Hardware watchdog enabled Hostname: unknown Configuring devices. checking ufs filesystems

/dev/rdsk/c1t0d0s5: is logging.

Step 5 If you are installing on aSparc-basedplatform, you must select your terminal type when a screen similar to the following is displayed:

What type of terminal are you using?

1)ANSI Standard CRT

2)DEC VT52

3)DEC VT100

4)Heathkit 19

5)Lear Siegler ADM31

6)PC Console

7)Sun Command Tool

8)Sun Workstation

9)Televideo 910

10)Televideo 925

11)Wyse Model 50

12)X Terminal Emulator (xterms)

13)CDE Terminal Emulator (dtterm)

13)Other

Type the number of your choice and press Return:

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-51

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Note OnOpteron-basedplatforms, you can select a terminal type from the picklist, or the default terminal type (from the serial port) is used. We recommend that you use the default terminal while you are installing software.

Enter the number that corresponds to the terminal you are using and press Enter. For example, if you are using an X terminal emulator, type12 and pressEnter.

The system displays information similar to the following:

Creating new rsa public/private host key pair

Creating new dsa public/private host key pair

Configuring network interface addresses: bge0 bge1 bge2 bge3.

Text similar to the following is displayed:

in.rdisc: No interfaces up

-Network Connectivity --------------------------------------------------------

Specify Yes if the system is connected to the network by one of the Solaris or vendor network/communication Ethernet cards that are supported on the Solaris CD. Refer to your hardware documentation for the current list of supported cards.

Specify No if the system is connected to a network/communication card that is not supported on the Solaris CD, and follow the instructions listed under Help.

Networked

---------

[X] Yes

[ ] No

-------------------------------------------------------------------------------

ESC-2_ContinueESC-6_Help

Step 6 Use the arrow keys to navigate, and press the spacebar to make your selection. Verify thatYes is selected, and pressESC-2 to continue.

Text similar to the following is displayed:

-Configure Multiple Network Interfaces ---------------------------------------

Multiple network interfaces have been detected on this system. Specify all of the network interfaces you want to configure.

Note: You must choose at least one interface to configure.

Network interfaces

------------------

[ ] bge0 [ ] bge1 [ ] bge2 [ ] bge3

-------------------------------------------------------------------------------

ESC-2_ContinueESC-6_Help

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-52

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Note This screen may show a different interface, depending on the platform and PCI card that are installed. For details, seeTable 2-1 on page 2-3 (“Device Names on Supported Host Platforms”).

Caution The interface configuration prompts do not provide an option to return to a previous step or exit interface configuration. If you enter an incorrect value, power down the Cisco PGW 2200 Softswitch, power up the Cisco PGW 2200 Softswitch, and return to Step 4.

Step 7 Select the interface(s) you want to configure and pressESC-2 to continue.

If you chose to configure a single interface, proceed to Step 9.

If you chose to configure multiple interfaces, proceed to Step 8.

Step 8 Text similar to the following is displayed:

-Primary Network Interface ---------------------------------------------------

On this screen you must specify which of the following network adapters is the system's primary network interface. Usually the correct choice is the lowest number. However, do not guess; ask your system administrator if you're not sure.

>To make a selection, use the arrow keys to highlight the option and press Return to mark it [X].

Primary network interface

----------------

[ ] bge0 [ ] bge1 [ ] bge2 [ ] bge3

-------------------------------------------------------------------------------

ESC-2_ContinueESC-6_Help

Select your primary network interface and press ESC-2 to continue.

Step 9 Text similar to the following is displayed:

-DHCP for bge0 -----------------------------------------------------------------

Specify whether or not this network interface should use DHCP to configure itself. Choose Yes if DHCP is to be used, or No if the network interface is to be configured manually.

NOTE: DHCP support will not be enabled, if selected, until after the system reboots.

Use DHCP for bge0

----------------

[ ] Yes

[X] No

-------------------------------------------------------------------------------

 

ESC-2_Continue

ESC-6_Help

 

Step 10 Verify thatNo is selected and pressESC-2 to continue.

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-53

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Text similar to the following is displayed:

-Host Name for bge0 -----------------------------------------------------------

Enter the host name which identifies this system on the network. The name must be unique within your domain; creating a duplicate host name will cause problems on the network after you install Solaris.

A host name must be at least two characters; it can contain letters, digits, and minus signs (-).

Host name for bge0:

-------------------------------------------------------------------------------

ESC-2_ContinueESC-6_Help

Caution If you are configuring your system with multiple interfaces, remember that each interface must have a unique name. Using the same name for multiple interfaces causes the installation script to enter a loop, forcing you to reboot your system.

Step 11 Type thehost name of the target Netra machine, and pressESC-2 to continue.

Note Formachine-specificinformation such as host name, see your notes in“Preparing for Sun Solaris Operating System and Cisco PGW 2200 Softswitch Software Installation” Table 1-3,“Machine-Specific Checklist” if you used the checklist to note the host name.

Text similar to the following is displayed:

-IP Address for bge0 -----------------------------------------------------------

Enter the Internet Protocol (IP) address for this network interface. It must be unique and follow your site's address conventions, or a system/network failure could result.

IP addresses contain four sets of numbers separated by periods (for example 129.200.9.1).

IP address:

--------------------------------------------------------------------------------

ESC-2_ContinueESC-6_Help

Step 12 Enter theIP address of this interface in dotted decimal format and pressESC-2 to continue.

Note See“Machine-Specific Checklist” inTable 1-3 if you used the checklist to record the IP address.

Text similar to the following is displayed:

- Subnet for bge0 --------------------------------------------------------------

 

 

 

On this screen you must specify whether this system is

part of a subnet. If

 

 

 

you specify incorrectly, the system will have problems

communicating on the

 

 

 

network after you reboot.

 

 

 

 

 

> To make a selection, use the arrow keys to highlight

the option and

 

 

 

press Return to mark it [X].

 

 

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

 

 

2-54

 

 

OL-18083-01

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

System part of a subnet

-----------------------

[X] Yes

[ ] No

-------------------------------------------------------------------------------

ESC-2_ContinueESC-6_Help

Note If you need to modify your IP addresses after you have installed Sun Solaris 10, there are three files you need to update, instead of the two files required in previous releases of Sun Solaris operating system software. The following files must be edited to in order to modify the IP address for an interface:

/etc/inet/hosts

/etc/hostname.inf_name

/etc/inet/ipnodes

Where inf_name is the name of the interface, such as bge1.

Step 13 Verify thatYes is selected (use the arrow keys to move the cursor toYes and press the spacebar to select it). PressESC-2 to continue.

A screen similar to the following is displayed:

-Netmask for bge0 -------------------------------------------------------------

On this screen you must specify the netmask of your subnet. A default netmask is shown; do not accept the default unless you are sure it is correct for your subnet. A netmask must contain four sets of numbers separated by periods (for example 255.255.255.0).

Netmask:

----------------------------------------------------------------------------------

ESC-2_ContinueESC-6_Help

Step 14 Enter thesite-specificSubnet Mask for the subnet (see“Site-Specific Information” inTable 1-2,if you recorded the information provided by your site administrator in this table). PressESC-2 to continue.

Text similar to the following is displayed:

-IPv6 for bge0 -----------------------------------------------------------------

Specify whether or not you want to enable IPv6, the next generation Internet Protocol, on this network interface. Enabling IPv6 will have no effect if this machine is not on a network that provides IPv6 service. IPv4 service will not be affected if IPv6 is enabled.

>To make a selection, use the arrow keys to highlight the option and press Return to mark it [X].

 

 

Enable IPv6 for bge0

 

 

-------------------

 

 

 

 

 

 

[ ] Yes

 

 

[X] No

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-55

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

-------------------------------------------------------------------------------

ESC-2_ContinueESC-6_Help

Note The system takes approximately 30 seconds to process this selection. A countdown appears in the display after you activate your choice.

Step 15 Verify thatNo is selected and pressESC-2 to continue.

Text similar to the following is displayed:

-Set the Default Route for bge0 -----------------------------------------------

To specify the default route, you can let the software try to detect one upon reboot, you can specify the IP address of the router, or you can choose None. Choose None if you do not have a router on your subnet.

> To make a selection, use the arrow keys to select your choice and press Return to mark it [X].

Default Route for bge0

--------------------------

[ ] Detect one upon reboot [X] Specify one

[ ] None

-------------------------------------------------------------------------------

ESC-2_ContinueESC-6_Help

Step 16 Verify thatSpecify one is selected and pressESC-2 to continue.

Text similar to the following is displayed:

- Default Route IP Address for bge0 --------------------------------------------

Enter the IP address of the default route. This entry will be placed in the /etc/defaultrouter file and will be the default route after you reboot (example 129.146.89.225).

Router IP Address for bge0

-------------------------------------------------------------------------------

ESC_Continue ESC-6_Help

Step 17 Enter the Router IP address of this interface in dotted decimal format and pressESC-2 to continue.

Note See“Solaris 10 Required Media Checklist” inTable 1-2 if you used the checklist to record the router IP address.

Text similar to the following is displayed:

-Confirm Information for bge0 -------------------------------------------------

>Confirm the following information. If it is correct, press F2; to change any information, press F4.

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-56

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Primary network interface: Yes

Use DHCP: No

Host name: va-host

IP address: 10.74.49.153

System part of a subnet: Yes

Netmask: 255.255.255.224

Enable IPv6: No

Default Route: Specify one

Router IP Address: 10.74.49.129

-------------------------------------------------------------------------------

ESC-2_ContinueESC-4_ChangeESC-6_Help

Step 18 Confirm the information displayed. PressESC-2 to accept the information and continue, or pressESC-4 to go back and make changes.

Note The system takes approximately 30 seconds to process this selection. A countdown appears in the display after you activate your choice.

If you chose to configure a single interface, proceed to Step 20.

If you chose to configure multiple interfaces, proceed to Step 19.

Step 19 Repeat steps 9 through 18 for your next interface. These steps should be repeated until all of your interfaces are configured.

Step 20 Text similar to the following is displayed:

- Configure Security Policy: --------------------------------------------------

Specify Yes if the system will use the Kerberos security mechanism.

Specify No if this system will use standard UNIX security.

Configure Kerberos Security

---------------------------

[ ] Yes

[X] No

-------------------------------------------------------------------------------

ESC-2_ContinueESC-6_Help

Step 21 Verify thatNo is selected and pressESC-2 to continue.

Text similar to the following is displayed:

-Confirm Information -

>Confirm the following information. If it is correct, press F2; to change any information, press F4.

Configure Kerberos Security: No

-------------------------------------------------------------------------------

ESC-2_ContinueESC-4_ChangeESC-6_Help

Step 22 Confirm your previous answer ofNo and pressESC-2 to continue.

Text similar to the following is displayed:

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

OL-18083-01

2-57

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

-Name Service ----------------------------------------------------------------

On this screen you must provide name service information. Select the name service that will be used by this system, or None if your system will either not use a name service at all, or if it will use a name service not listed here.

>To make a selection, use the arrow keys to highlight the option and press Return to mark it [X].

Name service

------------

[ ] NIS+

[ ] NIS

[ ] DNS

[ ] LDAP

[X] None

-------------------------------------------------------------------------------

ESC-2_ContinueESC-6_Help

Step 23 Use the arrow keys to move the cursor toNone and press the spacebar to select it. PressESC-2 to continue. Text similar to the following is displayed:

-DNS Search List -------------------------------------------------------------

On this screen you can enter a list of domains that will be searched when a DNS query is made. If you do not enter any domains, DNS will only search the DNS domain chosen for this system. The domains entered, when concatenated, may not be longer than 250 characters.

Search domain: yourdomain.com

Search domain:

Search domain:

Search domain:

Search domain:

Search domain:

-------------------------------------------------------------------------------

ESC-2_ContinueESC-6_Help

Step 24 Enter thenames of the search domains for this system and pressESC-2 to continue.

Note See“Machine-Specific Checklist”,Table 1-3,if you used the checklist to record the names of the search domains.

Text similar to the following is displayed:

-Confirm Information ---------------------------------------------------------

>Confirm the following information. If it is correct, press F2; to change any information, press F4.

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-58

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Name service: NONE

Domain name:

Server address(es):

Search domain(s): yourdomain.com

-------------------------------------------------------------------------------

ESC-2_ContinueESC-4_ChangeESC-6_Help

Step 25 Confirm your previous answers and pressESC-2 to continue.

Text similar to the following is displayed:

-Time Zone -------------------------------------------------------------------

On this screen you must specify your default time zone. You can specify a time zone in three ways: select one of the continents or oceans from the list, select other - offset from GMT, or other - specify time zone file.

>To make a selection, use the arrow keys to highlight the option and press Return to mark it [X].

Continents and Oceans

---------------------------------------

-[ ] Africa

x [ ] Americas

x [ ] Antarctica

x [ ] Arctic Ocean x [ ] Asia

x [ ] Atlantic Ocean x [ ] Australia

x [ ] Europe

v [ ] Indian Ocean

-------------------------------------------------------------------------------

ESC-2_ContinueESC-6_Help

Step 26 Select the time zone where the system is located.

Note The following two steps show how to set the time zone. The example shows United States Eastern time.

a.Use the arrow keys to move the cursor to Americas and press the spacebar to select it, then press ESC-2 to continue.

Text similar to the following is displayed:

-Country or Region -------------------------------------------------------

>To make a selection, use the arrow keys to highlight the option and press Return to mark it [X].

 

 

Countries and Regions

 

 

--------------------------

 

 

 

 

-

[ ] United States

 

x

[ ] Anguilla

 

x

[ ] Antigua & Barbuda

 

x

[ ] Argentina

 

x

[ ] Aruba

 

x

[ ] Bahamas

 

x

[ ] Barbados

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-59

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

x

[ ] Belize

 

x

[ ] Bolivia

 

x

[ ] Brazil

 

x

[ ] Canada

 

x

[ ] Cayman Islands

v

[ ] Chile

press Return to mark it [X].

-------------------------------------------------------------------------------

ESC-2_ContinueESC-6_Help

b.Use the arrow keys to move the cursor to United States and press the spacebar to select it, then press ESC-2 to continue.

Text similar to the following is displayed:

-Time Zone -------------------------------------------------------------------

>To make a selection, use the arrow keys to highlight the option and press Return to mark it [X].

Time zones

--------------------------------------------------------

-[ ] Eastern Time

x [ ] Eastern Time - Michigan - most locations x [ ] Eastern Time - Kentucky - Louisville area x [ ] Eastern Time - Kentucky - Wayne County

x [ ] Eastern Standard Time - Indiana - most locations x [ ] Eastern Standard Time - Indiana - Crawford County x [ ] Eastern Standard Time - Indiana - Starke County

x [ ] Eastern Standard Time - Indiana - Switzerland County x [ ] Central Time

x [ ] Central Time - Michigan - Wisconsin border x [ ] Central Time - North Dakota - Oliver County x [ ] Mountain Time

v [ ] Mountain Time - south Idaho & east Oregon

-------------------------------------------------------------------------------

ESC-2_ContinueESC-6_Help

c.Use the arrow keys to move the cursor to your time zone (in this example, “Eastern Time” is selected) and press the space bar to select it. Press ESC-2 to continue.

Text similar to the following is displayed:

-Date and Time ---------------------------------------------------------------

>Accept the default date and time or enter new values.

Date and

time: 2008-09-0802:58

Year

(4 digits)

: 2008

Month

(1-12)

: 09

Day

(1-31)

: 08

Hour

(0-23)

: 02

Minute

(0-59)

: 58

-------------------------------------------------------------------------------

ESC-2_ContinueESC-6_Help

Step 27 Enter the correct date and time and pressESC-2 to continue.

Text similar to the following is displayed:

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-60

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

-Confirm Information ---------------------------------------------------------

>Confirm the following information. If it is correct, press F2; to change any information, press F4.

Time zone: Eastern Time (US/Eastern)

Date and time: 2008-09-0802:58:00

-------------------------------------------------------------------------------

ESC-2_ContinueESC-4_ChangeESC-6_Help

Step 28 Verify the information and pressESC-2 to continue.

Text similar to the following might be displayed:

This system is configured with NFS version 4, which uses a domain name that is automatically derived from the system's name services. The derived domain name is sufficient for most configurations. In a few cases, mounts that cross different domains might cause files to be owned by "nobody" due to the lack of a common domain name.

Do you need to override the system's default NFS version 4 domain name (yes/no) ? [no] :

Step 29 Enterno to continue the reconfiguration process and pressEnter.

Text similar to the following is displayed:

For more information about how the NFS version 4 default domain name is derived and its impact, see the man pages for nfs(4) and nfsmapid(1m), and the System Administration Guide: Network Services.

rebooting system due to change(s) in /etc/default/init

syncing file systems... done

rebooting...

SC Alert: Host System has Reset

Probing system devices

Probing memory

Probing I/O buses

Note OnOpteron-basedplatforms, you can select a terminal type from the picklist, or the default terminal type (serial port). We recommend that you use the default terminal type while you are installing software.

Sun Fire V210, No Keyboard

Copyright 2005 Sun Microsystems, Inc. All rights reserved.

 

OpenBoot 4.18.5,

2048 MB memory installed, Serial #52030991.

 

Ethernet address

0:3:ba:19:ee:f, Host ID: 8319ee0f.

 

Initializing

1MB of memory at addr

103feec000

 

Initializing

1MB of memory at addr

103fee0000

 

Initializing

15MB of memory at addr

103f002000

 

Initializing

16MB of memory at addr

103e002000

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

 

2-61

 

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Initializing

992MB

of

memory at addr

1000000000

Initializing

1024MB

of

memory at addr

0

Rebooting with

command: boot

 

Boot device: /pci@1c,600000/scsi@2/disk@0,0:a

File and args:

SunOS Release 5.10 Version Generic_118833-1764-bit

Copyright 1983-2005Sun Microsystems, Inc. All rights reserved. Use is subject to license terms.

Hardware watchdog enabled Hostname: bge0

checking ufs filesystems /dev/rdsk/c1t0d0s5: is logging.

bge0 console login: root

Sep 8 03:00:15 bge0 login: ROOT LOGIN /dev/console

Step 30 If you want to enable root access to the Cisco PGW 2200 Softswitch via telnet, follow these steps:

a.Edit the /etc/default/login file, and make the following changes:

Comment out the line starting with “CONSOLE=” by inserting a “#” in front of this line.

Add the line “svcadm enable telnet” if you want to enable telnet.

Add the line “svcadm enable rlogin” if you want to enable remote login.

b.Save your changes to this file.

Step 31 If you want to enable root access to the Cisco PGW 2200 Softswitch via SSH, follow these steps:

a.Edit the /etc/ssh/sshd_config file and change the value of the PermitRootLogin parameter fromno toyes.

b.Save your changes to this file.

c.Identify the process ID of the sshd process by entering the following command:

ps -ef| grep ssh

d. Restart the sshd process and activate your changes by entering the following command:

kill -l process_id

Where process_id is the ssh process ID number identified in the previous step.

You have completed configuring your host. Proceed to the “Platform-Specific Installation Procedures” section on page 2-62.

Platform-SpecificInstallation Procedures

Complete the following steps to install files specific to your Cisco platform:

Step 1 Log in asroot and use the default password, vtghost. The system displays something similar to the following:

Sep

 

8 03:05:15

bge0 login: ROOT LOGIN /dev/console

Last

login: Mon

Sep 8

03:00:22 on console

Sun

Microsystems Inc.

SunOS 5.10

Generic January 2005

Step 2 Reinsert the CD into theCD-ROMdrive.

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-62

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Step 3 Mount theCD-ROMin the cdrom directory by entering the following command:

# mount-Fhsfs-oro /dev/dsk/devname /cdrom

Where devname is the device name for the primaryCD-ROMdrive. The following device names are valid:

c0t0d0s0—Devicename for primaryCD-ROMon aSparc-basedplatform.

c0t0d0p0—Devicename for primaryCD-ROMon anOpteron-basedplatform.

Step 4 Run thecore_finish script by entering the appropriate command:

For Sparc-based platforms: ./cdrom/core_finish/core_finish.sh

For Opteron-based platforms: ./cdrom/core_finish/core_finish.sh

Step 5 Enter the name of your host and pressEnter as prompted.

Note Entering the name of your host at this time does not set the UNIX host name value. The value you enter here is used to set up a crash directory: /var/hostname/crash

The system returns a response similar to the following:

Start installation of core extra packages

Adding <SUNWvts>

Processing package instance <SUNWvts> from </opt/xtrapkgs>

SunVTS Framework(sparc) 6.2,REV=2006.05.04.11.52

Using </opt> as the package base directory.

##Processing package information.

##Processing system information.

Installing SunVTS Framework as <SUNWvts>

## Installing part 1 of 1. /opt/SUNWvts/README /opt/SUNWvts/bin/.platform_table /opt/SUNWvts/bin/.sunvts_release /opt/SUNWvts/bin/.sunvts_sec /opt/SUNWvts/bin/.sunvts_sec_gss /opt/SUNWvts/bin/.version

...

/opt/SUNWvts/lib/sparcv9/libvtsutil.so <symbolic link> /opt/SUNWvts/lib/sparcv9/libvtsutil.so.1

[ verifying class <none> ]

Copyright 2006 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms.

Installation of <SUNWvts> was successful.

Adding <SUNWvtsr>

Processing package instance <SUNWvtsr> from </opt/xtrapkgs>

SunVTS Framework (Root)(sparc) 6.2,REV=2006.05.04.11.52

Using </> as the package base directory.

##Processing package information.

##Processing system information.

2 package pathnames are already properly installed.

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-63

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Installing SunVTS Framework (Root) as <SUNWvtsr>

## Installing part

1 of 1.

/etc/opt/SUNWvts/sunvts.conf.example

[ verifying class

<none> ]

Copyright 2006

Sun

Microsystems, Inc. All rights reserved.

Use is subject

to

license terms.

Installation of <SUNWvtsr> was successful.

Adding <SUNWvtsts>

Processing package instance <SUNWvtsts> from </opt/xtrapkgs>

SunVTS for Tests(sparc) 6.2,REV=2006.05.04.11.52

Using </opt> as the package base directory.

##Processing package information.

##Processing system information.

14 package pathnames are already properly installed.

Installing SunVTS for Tests as <SUNWvtsts>

## Installing part 1 of 1. /opt/SUNWvts/bin/bios.bin <symbolic link> /opt/SUNWvts/bin/cmos.bin <symbolic link> /opt/SUNWvts/bin/env6test /opt/SUNWvts/bin/hsclbtest /opt/SUNWvts/bin/i2c2test /opt/SUNWvts/bin/nalmtest

...

/opt/SUNWvts/lib/probe/sparcv9/vmemtest_probe.so /opt/SUNWvts/lib/probe/ssptest_probe.so /opt/SUNWvts/lib/probe/sunlink_probe.so

[ verifying class <none> ]

Copyright 2006 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms.

Installation of <SUNWvtsts> was successful.

Adding <SUNWexplo>

Processing package instance <SUNWexplo> from </opt/xtrapkgs>

Sun(TM) Explorer Data Collector(all) 5.5,REV=2006.07.14.01.46

##Executing checkinstall script. Copyright 1996-2006Sun Microsystems, Inc. All rights reserved.

Using </opt> as the package base directory.

##Processing package information.

##Processing system information.

Installing Sun(TM) Explorer Data Collector as <SUNWexplo>

##Executing preinstall script.

##Installing part 1 of 1. /opt/SUNWexplo/LICENSEREADME/LICENSE.txt /opt/SUNWexplo/LICENSEREADME/THIRDPARTYLICENSEREADME.txt /opt/SUNWexplo/LICENSEREADME/gzip-1.2.4a.tar.gz /opt/SUNWexplo/bin/capture.sparc

...

/opt/SUNWexplo/tools/var

/opt/SUNWexplo/tools/vtsst

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-64

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

/opt/SUNWexplo/tools/vxfs

/opt/SUNWexplo/tools/vxvm [ verifying class <none> ]

## Executing postinstall script. /usr/bin/catman is not available for use

Please run: catman -w-M /opt/SUNWexplo/manmanually

Installation of <SUNWexplo> was successful.

Adding <SUNWexplu>

Processing package instance <SUNWexplu> from </opt/xtrapkgs>

Sun(TM) Explorer Data Collector Config Files(all) 5.5,REV=2006.07.14.01.46

##Executing checkinstall script. Copyright 1996-2006Sun Microsystems, Inc. All rights reserved.

Using </> as the package base directory.

##Processing package information.

##Processing system information.

2 package pathnames are already properly installed.

Installing Sun(TM) Explorer Data Collector Config Files as <SUNWexplu>

##Installing part 1 of 1. /etc/opt/SUNWexplo/LICENSEREADME/LICENSE.txt /etc/opt/SUNWexplo/t3files.txt

[ verifying class <none> ]

Modifying /etc/opt/SUNWexplo/1280input.txt Modifying /etc/opt/SUNWexplo/alominput.txt Modifying /etc/opt/SUNWexplo/b1600input.txt Modifying /etc/opt/SUNWexplo/b1600switchinput.txt Modifying /etc/opt/SUNWexplo/ilominput.txt Modifying /etc/opt/SUNWexplo/indyinput.txt Modifying /etc/opt/SUNWexplo/ipmiinput.txt Modifying /etc/opt/SUNWexplo/saninput.txt Modifying /etc/opt/SUNWexplo/scinput.txt Modifying /etc/opt/SUNWexplo/se3kinput.txt Modifying /etc/opt/SUNWexplo/se6320input.txt Modifying /etc/opt/SUNWexplo/se6920input.txt Modifying /etc/opt/SUNWexplo/srscinput.txt Modifying /etc/opt/SUNWexplo/t3input.txt

[ verifying class <build> ]

##Executing postinstall script.

Installation of <SUNWexplu> was successful.

Adding <SUNWpsr>

Processing package instance <SUNWpsr> from </opt/xtrapkgs>

Solaris Print - LP Server, (root)(sparc) 13.1,REV=2005.01.21.15.53

Using </> as the package base directory.

##Processing system information.

11 package pathnames are already properly installed.

Installing Solaris Print - LP Server, (root) as <SUNWpsr>

## Executing preinstall script.

Copyright 2005 Sun Microsystems, Inc. All rights reserved.

 

Use is subject to

license terms.

 

## Installing part 1 of 1.

 

19 blocks

 

 

 

 

 

 

[ verifying class

<renameold> ]

 

[ verifying class

<preserve> ]

 

[ verifying class

<manifest> ]

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-65

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

## Executing postinstall script.

Installation of <SUNWpsr> was successful.

Adding <SUNWpcr>

Processing package instance <SUNWpcr> from </opt/xtrapkgs>

Solaris Print - Client, (root)(sparc) 13.1,REV=2005.01.21.15.53

Using </> as the package base directory.

##Processing package information.

##Processing system information.

10 package pathnames are already properly installed.

Installing Solaris Print - Client, (root) as <SUNWpcr>

## Installing part 1 of 1.

Copyright 2005 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms.

2 blocks

[ verifying class <preserve> ] [ verifying class <manifest> ]

## Executing postinstall script.

Installation of <SUNWpcr> was successful.

Adding <SUNWpcu>

Processing package instance <SUNWpcu> from </opt/xtrapkgs>

Solaris Print - Client, (usr)(sparc) 13.1,REV=2005.01.21.15.53

Using </> as the package base directory.

##Processing package information.

##Processing system information.

4 package pathnames are already properly installed.

Installing Solaris Print - Client, (usr) as <SUNWpcu>

## Installing part 1 of 1.

Copyright 2005 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms.

541 blocks

Installation of <SUNWpcu> was successful.

Adding <SUNWpsu>

Processing package instance <SUNWpsu> from </opt/xtrapkgs>

Solaris Print - LP Server, (usr)(sparc) 13.1,REV=2005.01.21.15.53

Using </> as the package base directory.

##Processing package information.

##Processing system information.

12 package pathnames are already properly installed.

Installing Solaris Print - LP Server, (usr) as <SUNWpsu>

## Installing part 1 of 1.

Copyright 2005 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms.

3090 blocks

Installation of <SUNWpsu> was successful.

Adding <SFWsudo>

Processing package instance <SFWsudo> from </opt/xtrapkgs>

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-66

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Sudo - superuser do(sparc) 1.6.8.5,REV=2006.03.26.16.30

Using </opt> as the package base directory.

##Processing package information.

##Processing system information.

Installing Sudo - superuser do as <SFWsudo>

## Installing part 1 of 1. /opt/sfw/READMEs/README.SFWsudo /opt/sfw/bin/sudo /opt/sfw/etc/sudoers /opt/sfw/man/man1m/sudo.1m /opt/sfw/man/man1m/visudo.1m /opt/sfw/man/man4/sudoers.4 /opt/sfw/sbin/visudo

[ verifying class <none> ]

Sudo is distributed under the following ISC-stylelicense:

Copyright (c) 1994-1996,1998-2004Todd C. Miller <Todd.Miller@courtesan.com>

Permission to use, copy, modify, and distribute this software for any purpose with or without fee is hereby granted, provided that the above copyright notice and this permission notice appear in all copies.

THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES

WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF

MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR

ANY SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES

WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN

ACTION OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF

OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.

Sponsored in part by the Defense Advanced Research Projects

Agency (DARPA) and Air Force Research Laboratory, Air Force

Materiel Command, USAF, under agreement number F39502-99-1-0512.

Additionally, err.c, lsearch.c, fnmatch.c, getcwd.c, snprintf.c, strcasecmp.c, fnmatch.h, err.h, and fnmatch.3 bear the following UCB license:

Copyright (c) 1987, 1989, 1990, 1991, 1993, 1994

The Regents of the University of California. All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1.Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2.Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3.Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND

ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE

ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE

FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS

OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)

HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT

LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY

OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-67

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

SUCH DAMAGE.

YOU MUST OBSERVE ANY AUTHORS' CONDITIONS WITH RESPECT TO

INDIVIDUAL COMPONENTS PROVIDED WITHIN THIS CODE. SUPPORT

FOR THE TECHNOLOGIES AND DOCUMENTATION IS NOT PROVIDED

BY SUN MICROSYSTEMS, INC.

THE TECHNOLOGIES AND DOCUMENTATION ARE PROVIDED "AS IS" WITHOUT TECHNICAL

SUPPORT OR WARRANTY OF ANY KIND, EITHER EXPRESS OR IMPLIED, INCLUDING, BUT NOT

LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A

PARTICULAR PURPOSE, OR NON-INFRINGEMENT.

Installation of <SFWsudo> was successful.

SUNW,Sun-Fire-V210does not need LOM packages

Validating patches...

Loading patches installed on the system...

Done!

Loading patches requested to install.

Done!

Checking patches that you specified for installation.

Done!

Approved patches will be installed in this order:

123526-01

Checking installed patches...

Verifying sufficient filesystem capacity (dry run method)...

Installing patch packages...

Patch 123526-01has been successfully installed.

See /var/sadm/patch/123526-01/logfor details

Patch packages installed:

SUNWcslr

Validating patches...

Loading patches installed on the system...

Done!

Loading patches requested to install.

Done!

Checking patches that you specified for installation.

Done!

Approved patches will be installed in this order:

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-68

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

119963-08

Checking installed patches...

Verifying sufficient filesystem capacity (dry run method)...

Installing patch packages...

Patch 119963-08has been successfully installed.

See /var/sadm/patch/119963-08/logfor details

Patch packages installed:

SUNWlibC

Validating patches...

Loading patches installed on the system...

Done!

Loading patches requested to install.

Done!

The following requested patches have packages not installed on the system

Package SUNWarc from directory SUNWarc in patch 119578-30is not installed on the system. Changes for package SUNWarc will not be applied to the system.

Package SUNWhea from directory SUNWhea in patch 119578-30is not installed on the system. Changes for package SUNWhea will not be applied to the system.

Package FJSVfmd from directory FJSVfmd in patch 119578-30is not installed on the system. Changes for package FJSVfmd will not be applied to the system.

Checking patches that you specified for installation.

Done!

Approved patches will be installed in this order:

119578-30

Checking installed patches...

Executing prepatch script...

Temporarily disabling fmd(1M)

Verifying sufficient filesystem capacity (dry run method)...

Installing patch packages...

Patch 119578-30has been successfully installed.

See /var/sadm/patch/119578-30/logfor details

Executing postpatch script...

Re-enablingfmd(1M)

Patch packages installed:

SUNWckr

SUNWcsl

SUNWcsu

SUNWfmd

Validating patches...

Loading patches installed on the system...

Done!

Loading patches requested to install.

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-69

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

Done!

The following requested patches have packages not installed on the system

Package SUNWarc from directory SUNWarc in patch 118833-36is not installed on the system. Changes for package SUNWarc will not be applied to the system.

Package SUNWarcr from directory SUNWarcr in patch 118833-36is not installed on the system. Changes for package SUNWarcr will not be applied to the system.

...

Package FJSVpiclu from directory FJSVpiclu in patch 118833-36is not installed on the system. Changes for package FJSVpiclu will not be applied to the system.

Checking patches that you specified for installation.

Done!

Approved patches will be installed in this order:

118833-36

Executing prePatch script...

Checking installed patches...

Executing prepatch script...

Disabling kernel module unloading ...

Verifying sufficient filesystem capacity (dry run method)...

Installing patch packages...

Patch 118833-36has been successfully installed.

See /var/sadm/patch/118833-36/logfor details

Executing postpatch script...

Patch packages installed:

SUNW1394

SUNWatfsr

SUNWatfsu

SUNWaudd

SUNWbart

SUNWbtool

SUNWcakr

SUNWcar

SUNWckr

SUNWcnetr

SUNWcpcu

SUNWcsd

SUNWcsl

SUNWcslr

SUNWcsr

SUNWcsu

SUNWdtrc

SUNWdtrp

SUNWefc

SUNWesu

SUNWib

SUNWintgige

SUNWipfr

SUNWipfu

SUNWipoib

SUNWkey

SUNWkrbr

SUNWkrbu

SUNWkvm

SUNWmdb

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-70

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating System

SUNWmdbr

SUNWmdr

SUNWmdu

SUNWnfsckr

SUNWnfscr

SUNWnfscu

SUNWnisu

SUNWopenssl-commands

SUNWopenssl-libraries

SUNWpcu

SUNWpd

SUNWpiclu

SUNWpsu

SUNWqos

SUNWrcmdc

SUNWroute

SUNWrpcib

SUNWsacom

SUNWses

SUNWsmapi

SUNWssad

SUNWtavor

SUNWtoo

SUNWudapltr

SUNWudapltu

SUNWuedg

SUNWugen

SUNWuksp

SUNWuprl

SUNWusb

SUNWusbs

SUNWwbsup

SUNWxcu4

SUNWxge

Completed installation of core extra packages

Start core hardening

Changing EEPROM settings..

Enable recording of failed login attempts

Dump content: kernel pages

Dump device: /dev/dsk/c1t0d0s3 (swap)

Savecore directory: /var/crash/sh-jingan

Savecore enabled: yes

Completed core hardening

CORE CD installation completed

Ejecting CORE CD...

Rebooting ..

Step 6 If you are installing on aSparc-basedplatform, perform the following steps. Otherwise, proceed to Step 7.

a.Change to the root directory by entering the following command and pressing Enter:

#cd /

b.Unmount the cdrom directory from the CD-ROMdrive by entering the following command and pressingEnter:

#umount /cdrom

c.Eject the CD from the CD-ROMby entering the following command and pressingEnter:

#eject /dev/dsk/c0t0d0s0

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-71

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

Step 7 Remove the CD from theCD-ROMdrive.

This completes the installation of platform-specificdata. Proceed to the“Loading the Sun Solaris 10 Operating Environment” section on page 2-72.

Loading the Sun Solaris 10 Operating Environment

This section contains the procedures used to load the software packages that create the Sun Solaris 10 operating environment on your host platforms. Table 2-2 lists the order in which the software packages should loaded onto your system, broken down by platform type.

The currently deployed Solaris 10 patch set is release 3.0(6) which is available on Cisco.com.

For Sparc-basedplatforms, go tohttp://www.cisco.com/cgi-bin/tablebuild.pl/mgc-sol10-sparc

For Opteron-basedplatforms, go tohttp://www.cisco.com/cgi-bin/tablebuild.pl/mgc-sol10-opteron

Table 2-2

Sun Solaris 10 Operating Environment Package Installation Order

 

 

 

 

 

 

 

 

Products

 

 

 

 

 

 

 

 

Cisco

 

Cisco

 

 

 

 

 

 

 

Cisco PGW 2200 Softswitch

HSI

 

BAMS

Sparc-basedPlatforms

Opteron-basedPlatforms

 

 

 

 

 

 

 

X

 

X

 

X

Installing the Sparc-based Solaris 10

Installing the Opteron-based Solaris

 

 

 

 

 

Patches Package (CSCOh022)

10 Patches Package (CSCOh032)

 

 

 

 

 

 

 

 

 

 

 

 

Configuring Disk Drives—Oneof

Configuring Disk Drives—Oneof

X

 

X

 

the following:

the following:

 

 

 

 

 

 

 

 

 

Systems with 36 GB, 73 GB, and

Systems with 36 GB, 73 GB, or

 

 

 

 

 

146 GB disk drives—Installing

146 GB disk drives—Installing

 

 

 

 

 

the Solstice DiskSuite

the Solstice DiskSuite

 

 

 

 

 

(CSCOh023)

(CSCOh023)

X

 

 

Systems with 18 GB disk

 

 

 

 

 

 

drives—Installing the Log and

 

 

 

 

 

 

Spool File Systems

 

 

 

 

 

 

(CSCOh024)

 

 

 

X

Cisco BAMS

 

 

 

 

 

 

platforms—Installing Cisco

 

 

 

 

 

 

BAMS Archive Partition

 

 

 

 

 

 

(CSCOh027)

 

 

 

 

 

 

 

 

X

 

X

 

X

Installing the Sparc-based

Installing the Opteron-based

 

 

 

 

 

Communications and Alarm

Communications Software Package

 

 

 

 

 

Software Package (CSCOh026)

(CSCOh036)

 

 

 

 

 

 

 

X

 

X

 

X

Installing the Verification Test Suite

Installing the Verification Test Suite

 

 

 

 

 

Script Package (CSCOh021)

Script Package (CSCOh021)

 

 

 

 

 

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-72

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

Installing the Sparc-basedSolaris 10 Patches Package (CSCOh022)

To install the Sparc-basedSolaris 10 Operating System Patches package (CSCOh022):

Step 1 If you are using theCD-ROM,load the Cisco Solaris 10 Operating Environment CD into theCD-ROMdrive. Enter the following command

# pkgadd-d /cdrom/cdrom0/CSCOh022.pkg

Text similar to the following is displayed:

The

following

packages are available:

1

CSCOh022

Media Gateway Controller Solaris 10 Patch Cluster

 

 

(sparc) 3.0(6)

Select package(s) you wish to process (or 'all' to process all packages). (default: all) [?,??,q]:

Note You can also download theSparc-basedSolaris 10 operating system patches package (CSCOh022) from Cisco.com. For example, download the CSCOh022 package to the /opt/SW folder on theSparc-basedplatform and use the command, pkgadd-d /opt/SW/CSCOh022.pkg.

Step 2 PressEnter to select the default value. Text similar to the following is displayed:

Processing package instance <CSCOh022> from </var/tmp/CSCOh022.pkg>

Media Gateway Controller Solaris 10 Patch Cluster(sparc) 3.0(6) Cisco Systems, Inc.

## Executing checkinstall script.

CSCOh022 checkinstall log file at /var/tmp/CSCOh022.checkinstall.log Platform is SUNW,Sun-Fire-V210

Using </opt/sun_install> as the package base directory.

##Processing package information.

##Processing system information.

1 package pathname is already properly installed.

##Verifying disk space requirements.

##Checking for conflicts with packages already installed.

The following files are already installed on the system and are being used by another package:

*/opt/sun_install <attribute change only>

*- conflict with a file which does not belong to any package.

Do you want to install these conflicting files [y,n,?,q]

Step 3 Typey and pressEnter to continue. Text similar to the following is displayed:

## Checking for setuid/setgid programs.

This package contains scripts which will be executed with super-userpermission during the process of installing this package.

Do you want to continue with the installation of <CSCOh022> [y,n,?]

Step 4 Typey and pressEnter to continue. Text similar to the following is displayed:

Installing Media Gateway Controller Solaris 10 Patch Cluster as <CSCOh0022>

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-73

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

The system lists the patches that it will install. This list will vary over time. A screen similar to the following is displayed:

….

!!

!!You must now change directories to /opt/sun_install and

!!run the installPatches.sh script as root.

!!

Installation of <CSCOh022> was successful.

Step 5 Change directory to /opt/sun_install and run the installPatches script by entering the following commands:

#cd /opt/sun_install

#./installPatches.sh

Note During the installation of the Solaris 10 patch cluster, some patches might fail with return codes 2, 8, or 35. This is normal and does not indicate a problem with the installation. The following is an explanation of these error codes:

2—Attemptingto apply a patch that is already applied.8—Attemptingto patch a package that is not installed.35—Alater version of the patch has already been installed.

Text similar to the following is displayed:

You are running as root - Good...

*** InstallPatches10 begins Wed Sep 10 01:16:25 EDT 2008 ***

VERSION='3.0(6)'

Platform is SUNW,Sun-Fire-V210

Install Solaris 10 patches from set 1 ...

Changed to /var/tmp directory

Now installing each patch from the patch cluster. There are a large number of these patches, and the install could take an hour or longer to complete. Please be patient. You can follow the progress of the install in the following log: /opt/sun_install/installPatches10.log

At least one patch failed to install. This may or

may

not indicate a problem. Please look

at the log file

after the rest of the patches

are applied

 

 

Install

Solaris 10 patches from set

2 ...

 

 

Changed

to /var/tmp directory

 

 

 

 

*** InstallPatches10 ends Wed

Sep 10 01:34:40 EDT

2008 ***

*************************************************

 

*

It

is necessary to reboot this

machine

*

 

*

for these patches to be

incorporated

*

 

*

the

operating system. Enter the

following

*

 

*

command and press Enter:

reboot ---r

*

 

*************************************************

Step 6 Type the following command and pressEnter to reboot the target machine.

#reboot ---r

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-74

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

Note If you used theCD-ROMdrive to load the Solaris 10 patch cluster, eject the CD prior to rebooting.

This completes the procedures for installing the Solaris 10 patches for Sparc-basedplatforms. Go toTable 2-2 on page 2-72 if you want to continue with the list for package installation. If you have questions or need assistance, see the“Obtaining Documentation and Submitting a Service Request” section on page x.

Installing the Opteron-basedSolaris 10 Patches Package (CSCOh032)

Note If you install CSCOh032 release 3.0(6) on top of release 3.0(5), run the CSCOh032 installation script once and reboot the system. See the following installation procedure.

If you do NOT install CSCOh032 release 3.0(6) on top of release 3.0(5), you need to run the CSCOh032 installation script twice. First run the CSCOh032 installation script, then reboot the system. Then run the CSCOh032 installation script again and reboot the system. After the second reboot is complete, use the uname -acommand to verify the patch level. If the patch level is127128-11,CSCOh032 is successfully installed.

To install the Opteron-basedSolaris 10 Operating System Patches package (CSCOh032):

Step 1 If you are using theCD-ROM,load the Cisco Solaris 10 Operating Environment CD into theCD-ROMdrive. Enter the following command:

# pkgadd-d /cdrom/cdrom0/CSCOh032.pkg

Text similar to the following is displayed:

The

following

packages are available:

1

CSCOh032

Media Gateway

Controller Solaris 10 Patch Cluster

 

 

(i386)

3.0(6)

 

Select package(s) you wish to process (or 'all' to process all packages). (default: all) [?,??,q]:

 

 

Note

You can also download the Opteron-basedSolaris 10 operating system patches package

 

 

 

(CSCOh032) from Cisco.com. For example, download the CSCOh032 package to the /opt/SW

 

 

 

folder on the Opteron-basedplatform and use the command, pkgadd-d

 

 

 

/opt/SW/CSCOh032.pkg.

 

 

 

 

 

Step 2

Press Enter to select the default value. Text similar to the following is displayed:

 

 

Processing package instance <CSCOh032> from </var/tmp/CSCOh032.pkg>

 

 

Media Gateway Controller PGW Specific Solaris 10 packages(i386) 3.0(6)

 

 

Cisco Systems, Inc.

 

 

## Executing checkinstall script.

 

 

CSCOh032 checkinstall log file at /var/tmp/CSCOh032.checkinstall.log

 

 

Platform is i86pc

 

 

This machine is running Solaris 5.10

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

 

OL-18083-01

 

 

 

2-75

 

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

Using </opt/sun_install> as the package base directory.

##Processing package information.

##Processing system information.

10 package pathnames are already properly installed.

##Verifying disk space requirements.

##Checking for conflicts with packages already installed.

##Checking for setuid/setgid programs.

This package contains scripts which will be executed with super-userpermission during the process of installing this package.

Do you want to continue with the installation of <CSCOh032> [y,n,?]

Step 3 Typey and pressEnter to continue. Text similar to the following is displayed:

Installing Media Gateway Controller Solaris 10 Patch Cluster as <CSCOh0032>

The system lists the patches that it will install. This list varies over time. Text similar to the following is displayed:

….

!!

!!You must now change directories to /opt/sun_install and

!!run the installPatches.sh script as root.

!!

Installation of <CSCOh032> was successful.

Step 4 Change directory to /opt/sun_install and run the installPatches script by entering the following commands:

#cd /opt/sun_install

#./installPatches.sh

Note During the installation of the Solaris 10 patch cluster, some patches might fail with return codes 1, 2, 8, and 35. This is normal and does not indicate a problem with the installation. The following is an explanation of these error codes:

1—Thepatch has been installed before.2—Attemptingto apply a patch that is already applied.8—Attemptingto patch a package that is not installed.

35—Alater version of the patch has already been installed.

Text similar to the following is displayed:

You are running as root - Good...

*** InstallPatches10 begins Tue Jul 8 11:14:25 GMT+8 2008 ***

VERSION='3.0(6)'

 

 

 

Platform is i86pc

 

 

 

Install Solaris 10 patches from set 1 ...

 

 

 

Changed to /var/tmp directory

 

 

 

Now installing each patch from the patch cluster. There are a large

 

 

 

number of these patches, and the install could take an hour or longer

 

 

 

to complete. Please be patient. You can follow the progress of the

 

 

 

install in the following log: /opt/sun_install/installPatches10.log

 

 

 

At least one patch failed to install. This may or may

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

2-76

 

OL-18083-01

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

not indicate a problem. Please look

at the log file

after the rest of the patches

are applied

 

Install

Solaris 10 patches from set

2 ...

 

Changed

to /var/tmp directory

 

 

 

*** InstallPatches10 ends Tue

Jul

8 11:14:41 GMT+8 2008 ***

*************************************************

*

It

is necessary to reboot this

machine

*

*

for these patches to be

incorporated

*

*

the

operating system. Enter the

following

*

*

command and press Enter:

reboot ---r

*

*************************************************

Step 5 Type the following command and pressEnter to reboot the target machine.

#reboot ---r

Note If you used theCD-ROMdrive to load the Solaris 10 patch cluster, eject the CD prior to rebooting.

Note If you have installed the Solaris DiskSuite package (CSCOh023) on your system, the messages below are displayed during system boot. They are normal Solaris DiskSuite startup messages and do not indicate any problem with your system.

WARNING force load of misc /md-transfailed

WARNING force load of misc /md-raidfailed

WARNING force load of misc /md-hotsparesfailed

WARNING force load of misc /md-spfailed

This completes the procedures for installing the Solaris 10 patches for Opteron-basedplatforms. Go toTable 2-2 on page 2-72 if you want to continue with the list for package installation. If you have questions or need assistance, see the“Obtaining Documentation and Submitting a Service Request” section on page x.

Installing the Solstice DiskSuite (CSCOh023)

The Sun Solstice DiskSuite program enables you to use the second disk drive as a mirror of the first to increase the availability of the system.You can install the DiskSuite program by running the scripts described below. The machine reboots several times during the installation process. The scripts minimize the possibility of running the scripts in the wrong order. However, you should ensure that the program is properly installed and take reasonable precautions to run the scripts correctly.

Note You must log in asroot to run the following DiskSuite installation script.

Note For Sun Fire X4600 and Sun Netra X4200 M2 platforms, do not change the default hard disk boot order in the BIOS settings. If the primary disk is changed from the default of c3t0d0, the DiskSuite installation fails.

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-77

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

Step 1 Load the Cisco Solaris 10 Operating Environment CD into theCD-ROMdrive. Enter the following command to install the DiskSuite installation scripts:

# pkgadd-d /cdrom/cdrom0/CSCOh023.pkg

Text similar to the following is displayed.

The

following

packages are available:

1

CSCOh023

Media Gateway Controller Solaris 10 DiskSuite

 

 

(sparc,i386) 3.0(6)

Select package(s) you wish to process (or 'all' to process all packages). (default: all) [?,??,q]:

Note You can also download the Solaris 10 DiskSuite package (CSCOh023) from Cisco.com. For example, download the CSCOh023 package to the /opt/SW folder on the platform and use the command, pkgadd-d /opt/SW/CSCOh023.pkg.Make sure you downloads theplatform-specificpackage for your platform(Sparc-basedorOpteron-based).

Step 2 PressEnter to accept the default answerall. Text similar to the following is displayed:

Processing package instance <CSCOh023> from </var/tmp/CSCOh023.pkg>

Media Gateway Controller Solaris 10 DiskSuite(sparc,i386) 3.0(6) Cisco Systems, Inc.

## Executing checkinstall script.

CSCOh023 checkinstall log file at /var/tmp/CSCOh023.checkinstall.log Platform is SUNW,Sun-Fire-V210

This machine is running Solaris 5.10

Using </opt/sun_install> as the package base directory.

##Processing package information.

##Processing system information.

2 package pathnames are already properly installed.

##Verifying disk space requirements.

##Checking for conflicts with packages already installed.

##Checking for setuid/setgid programs.

This package contains scripts which will be executed with super-userpermission during the process of installing this package.

Do you want to continue with the installation of <CSCOh023> [y,n,?]

Step 3 Entery and pressEnter to continue with the installation.

Installing Media Gateway Controller Solaris 10 DiskSuite as <CSCOh023>

## Executing preinstall script.

No PGW software found - this package can be installed ## Installing part 1 of 1. /opt/sun_install/DiskSuite/admin.file /opt/sun_install/DiskSuite/install_disksuite_1.sh /opt/sun_install/DiskSuite/install_disksuite_2.sh /opt/sun_install/DiskSuite/query_2nd_disk.cmd /opt/sun_install/DiskSuite/rm_disksuite_1.sh /opt/sun_install/DiskSuite/rm_disksuite_2.sh

[ verifying class <none> ]

## Executing postinstall script.

!!

!!You must now change directories to

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-78

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

!!/opt/sun_install/DiskSuite and run the

!!install_disksuite_1.sh script as root.

Installation of <CSCOh023> was successful.

Step 4 Change directories. Enter the following command:

cd /opt/sun_install/DiskSuite

Step 5 Run the first script. Enter the following command:

./install_disksuite_1.sh

Text similar to the following is displayed:

You are running as root - Good...

Output will be logged in /opt/sun_install/DiskSuite/DiskSuite_1.log

This script installs Disk Suite on an PGW system.

It assumes that Solaris 10 is installed and the disks are correctly formatted and ready to go.

**** IMPORTANT NOTE ****

In order to install DiskSuite, you MUST HAVE allocated an unassigned, 15-30Mbdisk partition in disk slice 4 of your primary disk. IF THIS PARTITION DOES NOT EXIST YOUR DISKSUITE INSTALLATION WILL FAIL, and IT MAY CORRUPT YOUR DISK!

I will now run a command which will show you the current disk partitions. You can see the number of sectors allocated in the column marked Sector Count

If you do not see a line which shows that partition 4 is allocated DO NOT CONTINUE WITH THIS INSTALLATION!

You can see the number of sectors allocated in the column marked Sector Count. Sectors may vary in size from 512 bytes to 4096 bytes and perhaps even larger Warning: Current Disk has mounted partitions.

/dev/dsk/c1t0d0s0 is currently mounted on /. Please see umount(1M). /dev/dsk/c1t0d0s1 is currently mounted on /var. Please see umount(1M). /dev/dsk/c1t0d0s3 is currently used by swap. Please see swap(1M). /dev/dsk/c1t0d0s5 is currently mounted on /opt. Please see umount(1M).

Using Disk Controller c1

If this is not the correct controller, please exit this script and contact tech support

Here is your current disk partition setup. Look for partition 4

*/dev/dsk/c1t0d0s0 partition map

*Dimensions:

*512 bytes/sector

*424 sectors/track

*24 tracks/cylinder

*10176 sectors/cylinder

*14089 cylinders

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-79

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

*14087 accessible cylinders

*Flags:

*1: unmountable

*10: read-only

*

 

 

 

 

 

 

*

 

 

First

Sector

Last

 

* Partition

Tag

Flags

Sector

Count

Sector

Mount Directory

0

2

00

8201856

4100928

12302783

/

1

7

00

12302784

10247232

22550015

/var

2

5

00

0

143349312

143349311

 

3

3

01

0

8201856

8201855

 

4

0

00

22550016

50880

22600895

 

5

0

00

22600896

116647488

139248383

/opt

6

0

00

139248384

4100928

143349311

 

Do you want to continue? (y/n) [N]

Step 6 Typey and pressEnter to continue the installation. Text similar to the following is displayed:

Searching for disks...done

AVAILABLE DISK SELECTIONS:

0.c1t0d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> /pci@1c,600000/scsi@2/sd@0,0

1.c1t1d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> /pci@1c,600000/scsi@2/sd@1,0

Specify disk (enter its number): selecting c1t0d0 [disk formatted]

Warning: Current Disk has mounted partitions.

/dev/dsk/c1t0d0s0 is

currently mounted on /. Please see umount(1M).

/dev/dsk/c1t0d0s1 is

currently mounted on /var. Please see umount(1M).

/dev/dsk/c1t0d0s3 is

currently used by swap. Please see swap(1M).

/dev/dsk/c1t0d0s5 is

currently mounted on /opt. Please see umount(1M).

FORMAT MENU:

 

 

disk

-

select a disk

type

-

select (define) a disk type

partition

-

select (define) a partition table

current

-

describe the current disk

format

-

format and analyze the disk

repair

-

repair a defective sector

label

-

write label to the disk

analyze

-

surface analysis

defect

-

defect list management

backup

-

search for backup labels

verify

-

read and display labels

save

-

save new disk/partition definitions

inquiry

-

show vendor, product and revision

volname

-

set 8-charactervolume name

!<cmd>

-

execute <cmd>, then return

quit

 

 

format>

 

 

PARTITION MENU:

0- change `0' partition

1- change `1' partition

2- change `2' partition

3- change `3' partition

4- change `4' partition

5- change `5' partition

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-80

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

6- change `6' partition

7- change `7' partition select - select a predefined table

modify - modify a predefined partition table

name

- name the current table

print

- display the current table

label

- write partition map and label to the disk

!<cmd> - execute <cmd>, then return

quit

 

 

 

partition> Enter table name

(remember quotes):

partition>

 

 

 

FORMAT MENU:

 

 

 

disk

 

- select

a disk

type

 

- select

(define) a disk type

partition

- select

(define) a partition table

current

 

- describe the current disk

format

 

- format

and analyze the disk

fdisk

 

- run the fdisk program

repair

 

- repair

a defective sector

label

 

- write label to the disk

analyze

 

- surface analysis

defect

 

- defect

list management

backup

 

- search

for backup labels

verify

 

- read and display labels

save

 

- save new disk/partition definitions

inquiry

 

- show vendor, product and revision

volname

 

- set 8-charactervolume name

!<cmd>

 

- execute <cmd>, then return

quit

 

 

 

format> Saving new

disk and

partition definitions

Enter file name["./format.dat"]: format> Searching for disks...done

AVAILABLE DISK SELECTIONS:

0.c1t0d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> /pci@1c,600000/scsi@2/sd@0,0

1.c1t1d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424>

/pci@1c,600000/scsi@2/sd@1,0

Specify disk (enter its number): selecting c1t1d0 [disk formatted]

 

FORMAT MENU:

 

 

 

 

 

 

disk

- select a disk

 

type

- select (define) a disk type

 

partition

- select (define) a partition table

 

current

- describe the current disk

 

format

- format and analyze the disk

 

fdisk

- run the fdisk program

 

repair

- repair a defective sector

 

label

- write label to the disk

 

analyze

- surface analysis

 

defect

- defect list management

 

backup

- search for backup labels

 

verify

- read and display labels

 

save

- save new disk/partition definitions

 

inquiry

- show vendor, product and revision

 

volname

- set 8-charactervolume name

 

!<cmd>

- execute <cmd>, then return

 

quit

 

 

 

 

 

 

format>

 

 

 

 

 

 

PARTITION MENU:

 

 

 

 

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-81

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

 

 

 

 

0

- change `0' partition

 

 

 

 

 

 

 

 

1

- change `1' partition

 

 

 

 

 

 

 

 

2

- change `2' partition

 

 

 

 

 

 

 

 

3

- change `3' partition

 

 

 

 

 

 

 

 

4

- change `4' partition

 

 

 

 

 

 

 

 

5

- change `5' partition

 

 

 

 

 

 

 

 

6

- change `6' partition

 

 

 

 

 

 

 

 

7

- change `7' partition

 

 

 

 

 

 

 

 

select - select a predefined table

 

 

 

 

 

 

 

 

modify

- modify a predefined partition table

 

 

 

 

 

 

 

name

- name the current table

 

 

 

 

 

 

 

 

print

- display the current table

 

 

 

 

 

 

 

 

label

- write partition map and label to the disk

 

 

 

 

 

 

!<cmd> - execute <cmd>, then return

 

 

 

 

 

 

 

 

quit

 

 

 

 

 

 

 

 

 

 

 

partition>

 

0. CISCO

 

 

 

 

 

 

 

 

 

1. original

 

 

 

 

 

 

 

 

 

Specify

table (enter

its number)[1]:

 

 

 

 

 

 

 

partition> Current

partition table (CISCO):

 

 

 

 

 

 

 

Total disk cylinders

available: 14087 + 2 (reserved cylinders)

 

 

 

 

 

Part

Tag

Flag

Cylinders

Size

Blocks

 

 

0

root

 

wm

806 -

1208

1.96GB

(403/0/0)

4100928

 

1

var

 

wm

1209 -

2215

4.89GB

(1007/0/0)

10247232

 

2

backup

 

wm

0 - 14086

68.35GB

(14087/0/0) 143349312

 

3

swap

 

wu

0 -

805

3.91GB

(806/0/0)

8201856

 

 

 

 

4 unassigned

 

wm

2216 -

2220

24.84MB

(5/0/0)

50880

 

 

 

 

5 unassigned

 

wm

2221 - 13683

55.62GB

(11463/0/0) 116647488

 

 

 

 

6 unassigned

 

wm

13684 - 14086

1.96GB

(403/0/0)

4100928

 

 

 

 

7 unassigned

 

wm

0

 

0

(0/0/0)

0

 

 

 

 

partition> Ready to label disk, continue?

 

 

 

 

 

 

 

partition>

 

 

 

 

 

 

 

 

 

 

 

FORMAT MENU:

 

 

 

 

 

 

 

 

 

 

 

 

disk

 

-

select a disk

 

 

 

 

 

 

 

 

type

 

-

select (define) a disk type

 

 

 

 

 

 

 

partition

-

select (define) a partition table

 

 

 

 

 

 

 

current

 

-

describe the current disk

 

 

 

 

 

 

 

format

 

-

format and analyze the disk

 

 

 

 

 

 

 

fdisk

 

-

run the fdisk program

 

 

 

 

 

 

 

 

repair

 

-

repair a defective sector

 

 

 

 

 

 

 

label

 

-

write label to the disk

 

 

 

 

 

 

 

analyze

 

-

surface analysis

 

 

 

 

 

 

 

 

defect

 

-

defect list management

 

 

 

 

 

 

 

 

backup

 

-

search for backup labels

 

 

 

 

 

 

 

verify

 

-

read and display labels

 

 

 

 

 

 

 

save

 

-

save new disk/partition definitions

 

 

 

 

 

 

inquiry

 

-

show vendor, product and revision

 

 

 

 

 

 

 

volname

 

-

set 8-charactervolume name

 

 

 

 

 

 

 

!<cmd>

 

-

execute <cmd>, then return

 

 

 

 

 

 

 

quit

 

 

 

 

 

 

 

 

 

 

 

format>

Finished disk partitioning...

 

 

 

 

 

 

 

metadb: waiting on

/etc/lvm/lock

 

 

 

 

 

 

 

 

d1: Concat/Stripe is

setup

 

 

 

 

 

 

 

 

d2: Concat/Stripe is

setup

 

 

 

 

 

 

 

 

d4: Concat/Stripe is

setup

 

 

 

 

 

 

 

 

d5: Concat/Stripe is

setup

 

 

 

 

 

 

 

 

d7: Concat/Stripe is

setup

 

 

 

 

 

 

 

 

d8: Concat/Stripe is

setup

 

 

 

 

 

 

 

 

d10: Concat/Stripe

is setup

 

 

 

 

 

 

 

 

d11: Concat/Stripe

is setup

 

 

 

 

 

 

 

 

d13: Concat/Stripe

is setup

 

 

 

 

 

 

 

 

d14: Concat/Stripe

is setup

 

 

 

 

 

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

 

 

 

 

2-82

 

 

 

 

 

 

 

 

 

OL-18083-01

 

 

 

 

 

 

 

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

d3: Mirror is setup d6: Mirror is setup d9: Mirror is setup d12: Mirror is setup d15: Mirror is setup

The machine will now reboot.

Wait for the system to come up. Then log in as root, cd /opt/sun_install/DiskSuite and continue by executing the script install_disksuite_2.sh

Press the ENTER key to continue:

Step 7 PressEnter to reboot your system.

Step 8 Once the system has completed its reboot, log in asroot and change directories to /opt/sun_install/DiskSuite. Enter the following command:

cd /opt/sun_install/DiskSuite

Step 9 Run the second script. Enter the following command:

./install_disksuite_2.sh

Text similar to the following is displayed:

You are running as root - Good...

Output will be logged in /opt/sun_install/DiskSuite/DiskSuite_2.log

This is part 2 of the script that installs

Disk Suite on an PGW system.

It assumes that Solaris 10 is installed

You should have already run install_disksuite_1.sh which installs and configures the disks

This script attaches the second disk and starts the disk replication process

Do you want to continue? (y/n) [N] y

Step 10 Typey and pressEnter to continue the installation. Text similar to the following is displayed:

/dev/dsk/c1t0d0s0 is part of SVM volume stripe:d1. Please see metaclear(1M). /dev/dsk/c1t0d0s1 is part of SVM volume stripe:d4. Please see metaclear(1M). /dev/dsk/c1t0d0s3 is part of SVM volume stripe:d7. Please see metaclear(1M). /dev/dsk/c1t0d0s4 contains an SVM mdb. Please see metadb(1M).

/dev/dsk/c1t0d0s5 is part of SVM volume stripe:d10. Please see metaclear(1M). /dev/dsk/c1t0d0s6 is part of SVM volume stripe:d13. Please see metaclear(1M). /dev/dsk/c1t1d0s0 is part of SVM volume stripe:d2. Please see metaclear(1M).

/dev/dsk/c1t1d0s1 is part of SVM volume stripe:d5. Please see metaclear(1M). /dev/dsk/c1t1d0s3 is part of SVM volume stripe:d8. Please see metaclear(1M). /dev/dsk/c1t1d0s4 contains an SVM mdb. Please see metadb(1M).

/dev/dsk/c1t1d0s5 is part of SVM volume stripe:d11. Please see metaclear(1M). /dev/dsk/c1t1d0s6 is part of SVM volume stripe:d14. Please see metaclear(1M). d3: submirror d2 is attached

 

d6: submirror

d5

is attached

 

d9: submirror

d8

is attached

 

d12: submirror d11

is attached

 

d15: submirror d14

is attached

 

Disk Suite is

now configured and will start to

 

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

 

 

OL-18083-01

 

 

 

 

2-83

 

 

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

mirror to the second disk. It will take some time for the disk to be completely mirrored. Depending on the size of the disk, it may take up to several hours

The system will repeatedly execute the command: /usr/sbin/metastat |grep done

When there is no output from this command, the replication will be complete and this script will terminate

At that time, it will

be safe to reboot the machine

 

 

Resync

in progress: 0

% done

Resync

in progress: 0

% done Resync in progress: 0

% done

Resync in progress: 0

% done

Resync in progress: 0

% done

Resync

in progress: 0

% done

Resync

in progress: 0

% done

Resync in progress: 0

% done

Resync in progress: 2

% done

Resync in progress: 0

% done

Resync

in progress: 0

% done

Resync

in progress: 1

% done

Resync in progress: 1

% done

Resync in progress: 4

% done

Resync in progress: 1

% done

Note The system continues to issue thesere-synchronizationmessages until the replication is complete. Once the replication is complete, the system returns a prompt.

Note This portion of the installation istime-intensive.The amount of time required to complete the replication is dependent upon the size of the disk drives in your host. It may take several hours.

Resync in progress: 94 % done

Resync in progress: 96 % done

Resync in progress: 98 % done

The Disk Suite installation is now complete

Press the ENTER key to continue:

Step 11 PressEnter to continue the installation. Text similar to the following is displayed:

The following procedure should be used to add an alias in the boot rom so you can boot off of the secondary disk if necessary

Get the information from the system on the second disk

# prtconf -vp|grep pci |grep disk1

NOTE: disk1 is a system maintained standard for the system's second hard disk. If the prtconf command returns this information, it can be used to boot the second disk

without any additional changes

To create an alias name other than disk1 for the second boot disk in the NVRAM, use the information from the prtconf command (above)

# eeprom nvramrc='devalias backup_root /pci@1f,0/pci@1/scsi@8/disk@1,0'

Check the alias

eeprom |grep nvramrc #use-nvramrc?=true

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-84

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

nvramrc=devalias backup_root /pci@1f,0/pci@1/scsi@8/disk@1,0

Then bring the machine down to the boot prompt

# /usr/sbin/shutdown -g0-y-i0

.... system shuts down....

ok boot backup_root

The machine should reboot from the second disk. The following text will be found in the boot output. This ensures that the machine was working from the second drive:

a)Executing last command: boot backup_root

b)Boot device: /pci@1f,0/pci@1/scsi@8/disk@1,0 File and args:

The boot device listed should match the output from the nvramrc= output from above

Step 12 If you want to set up your system to be able to reboot from the second disk, proceed to the“Rebooting from the Mirrored (Secondary) Disk on Sparc-based Platforms” section on page 2-85 or the“Rebooting from the Mirrored (Secondary) Disk on Opteron-based Platforms” section on page 2-87.Otherwise, proceed to Step 15.

Step 13 Type the following command and pressEnter to reboot your system.

#/usr/sbin/shutdown -g0-y-i6

The DiskSuite installation is now complete. If you want to configure your system to reboot from the mirrored disk, go to the “Rebooting from the Mirrored (Secondary) Disk on Sparc-based Platforms” section on page 2-85 or the“Rebooting from the Mirrored (Secondary) Disk on Opteron-based Platforms” section on page 2-87.If you want to return to the list for package installation, go toTable 2-2 on page 2-72.

Rebooting from the Mirrored (Secondary) Disk on Sparc-basedPlatforms

Caution Rebooting from the mirrored (secondary) disk is normally done only after a catastrophic failure of the primary disk.

Perform the following procedure to add an alias in the boot ROM so you can boot from the secondary disk, if necessary.

Step 1 Get the information from the system on the second disk that you will boot from. Type the following command and pressEnter:

# prtconf -vp| grep pci | grep disk1

Text similar to the following is displayed:

disk1: ‘/pci@1f,0/pc1@1/scsi@8/disk1,0’

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-85

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

Note Disk1 is asystem-maintainedstandard for the system's second hard disk.

a.If the prtconf command returns the above information, you can use it to boot the second disk without any additional changes. Proceed toStep 4.

b.If you do not wish to use the above default information, create an alias name other than disk1 for the second boot disk in the NVRAM by using the information from the prtconf command (above).

# eeprom nvramrc='devalias backup_root /pci@1f,0/pci@1/scsi@8/disk@1,0'

Step 2 Check the alias you created by typing the following commands and pressingEnter:

eeprom |grep nvramrc

Text similar to the following is displayed:

use-nvramrc?=true

nvramrc=devalias backup_root /pci@1f,0/pci@1/scsi@8/disk@1,0

Note In the steps that follow, wherever you see “disk1” replace it with the alias you configured above.

Step 3 Before shutting down the system, check the progress of the mirroring to make sure that replication is complete.Type the following the command to check the progress of the mirroring. An Okay response means that disk mirroring is complete.

/usr/sbin/metastat

Warning DO NOT REBOOT until the replication is complete and the mirrors are in theOkay state.

Step 4 When the replication is complete, bring the machine down to the boot prompt. Type the following command and pressEnter:

# /usr/sbin/shutdown -g0-y-i0

Text similar to the following is displayed:

The system is coming down. Please wait. System services are now being stopped.

.

.

.

The system is down.

.

.

.

Program terminated ok

Step 5 In OK mode, enter the following command and press Enter:

ok boot disk1

Text similar to the following is displayed:

Res

LOM event: +0h5m53s host resetting

.

.

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-86

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

.

Executing last command: boot disk1

Boot device: /pci@1f,0/pci@1/scsi@8/disk@1,0 File and args: SunOS Release 5.10 Version Generic_108528-1364-bit

Copyright 1983-2004Sun Microsystems, Inc. All rights reserved.

The machine should reboot from the second disk.

Step 6 Verify that the following text is displayed in the boot output (see the output inStep 4, above). This ensures that the machine was working from the second drive:

Executing last command: boot disk1

Boot device: /pci@1f,0/pci@1/scsi@8/disk@1,0 File and args:

Note If you have installed the Solaris DiskSuite package (CSCOh023) on your system, the messages below are displayed during system boot. They are normal Solaris DiskSuite startup messages and do not indicate any problem with your system.

WARNING force load of misc /md-transfailed

WARNING force load of misc /md-raidfailed

WARNING force load of misc /md-hotsparesfailed

WARNING force load of misc /md-spfailed

Step 7 The boot device listed should match the output from the "nvramrc=" line inStep 2.

This completes the procedures for rebooting from the mirrored (secondary) disk on Sparc-basedplatforms. If you want to return to the list for package installation, go toTable 2-2 on page 2-72.

Rebooting from the Mirrored (Secondary) Disk on Opteron-basedPlatforms

Caution Rebooting from the mirrored (secondary) disk is normally done only after a catastrophic failure of the primary disk.

Perform the following procedure to reboot from the mirrored (secondary) disk on Opteron-basedplatforms.

Step 1 Check the file /boot/grub/menu.lst to make sure that the section foralternate boot exists in the file.

That section is similar to the following:

title alternate boot root (hd1,0,a)

kernel /platform/i86pc/multiboot module /platform/i86pc/boot_archive

Step 2 Before shutting down the system, check the progress of the mirroring to make sure that replication is complete.Type the following the command to check the progress of the mirroring. An Okay response means that disk mirroring is complete. At the end of the system output, you see two devices whose Reloc are shown as Yes.

/usr/sbin/metastat

Text similar to the following is displayed:

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-87

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

d12: Mirror Submirror 0: d10

State: Okay

Submirror 1: d11

State: Okay Pass: 1

Read option: roundrobin (default) Write option: parallel (default) Size: 116599770 blocks (55 GB)

...

 

 

 

 

 

 

 

d14: Submirror of d15

 

 

 

 

 

State: Okay

 

 

 

 

 

 

Size: 4096575 blocks (2.0 GB)

 

 

 

 

Stripe 0:

 

 

 

 

 

 

 

Device

Start Block

Dbase

State Reloc Hot Spare

 

 

 

c3t3d0s6

0

No

Okay

Yes

Device Relocation Information:

 

 

 

Device

Reloc

Device ID

 

 

 

c3t3d0

Yes

id1,sd@n500000e01861aae0

 

 

c3t2d0

Yes

id1,sd@n500000e01860a690

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Warning DO NOT REBOOT until the replication is complete and the mirrors are in theOkay state.

Step 3 When the replication is complete, bring the machine down to the boot prompt. Type the following command and pressEnter:

# /usr/sbin/shutdown -g0-y-i6

Text similar to the following is displayed:

Shutdown started. Thu Aug 14 12:18:21 CDT 2008

Changing to init state 6 - please wait

Broadcast Message from root (pts/1) on sh-agroveThu Aug 14 12:18:21...

THE SYSTEM sh-agroveIS BEING SHUT DOWN NOW ! ! !

Log off now or risk your files being damaged

Step 4 Choosealternate boot in the GRUB menu and pressEnter.

This completes the procedures for rebooting from the mirrored (secondary) disk on Opteron-basedplatforms. If you want to return to the list for package installation, go toTable 2-2 on page 2-72.

Removing the Solstice DiskSuite

Note This section applies to the Cisco PGW 2200 Softswitch Host running either the

Cisco PGW 2200 Softswitch or HSI software. You must remove Cisco PGW 2200 Softswitch, HSI, or BAMS software before you remove the DiskSuite. The following procedure works only from platforms that have been mirrored by use of the procedure provided in the“Installing the Solstice DiskSuite (CSCOh023)” section on page 2-77.

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-88

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

This procedure un-mirrorsthe disk partitions and removes the DiskSuite application from the platform. Use this procedure if a system has DiskSuite installed and you no longer wish to use CSCOh024 to configure the second disk for the log and spool directories.

If the platform is configured with customer-specificinformation,be sure to back up this information before the partitions are un-mirrored and DiskSuite is removed. Consult the appropriate document, depending on the software installed.

Step 1 Log in asroot. Use themetastat command to verify that the state of all the mirrors isOkay.

Step 2 Type the following commands to run the script and pressEnter:

cd /opt/sun_install/DiskSuite

./rm_disksuite_1.sh

The ./rm_disksuite_1.sh command detaches the mirrored disks and restores the original disk partition file in /etc/vfstab. The machine reboots after detaching the mirrored disks and restoring the original disk partition file.

Step 3 Log in asroot and change directory to/opt/sun_install/DiskSuite. Enter the following command:

cd /opt/sun_install/DiskSuite

Step 4 Run the script ./rm_disksuite_2.sh:

./rm_disksuite_2.sh

This script clears the disk mirrors and removes the DiskSuite software packages from the system.

Step 5 Enter the following command and pressEnter to remove the package, CSCOh023:

pkgrm CSCOh023

Text similar to the following is displayed:

The following package is currently installed:

CSCOh023 Media Gateway Controller Solaris 10 DiskSuite (sparc,i386) 3.0(6)

Do you want to remove this package? [y,n,?,q] y

...

Removal of <CSCOh023> was successful.

This completes the DiskSuite removal.

Installing the Log and Spool File Systems (CSCOh024)

Note This section applies to a Cisco PGW 2200 Softswitch host with18-GBdisk drives running the Cisco PGW 2200 Softswitch software.

Note If the DiskSuite software is installed and configured, you must first follow the procedure in the“Removing the Solstice DiskSuite” section on page 2-88 to remove the DiskSuite software before configuring the second disk to be used for the log and spool file systems.

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-89

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

To determine whether DiskSuite is installed and configured, run the /usr/sbin/metastat command. If the command is found and it displays the status of mirrors, it indicates that DiskSuite is installed and configured.

Note For the device names for each platform type, see Table 2-1 on page 2-3 (Device Names on Supported Host Platforms).

This procedure enables you to move the log and spool file system to the second disk drive to increase the capacity for log, alarm, measurement, and CDR files. This improves the performance of the host. If CSCOh024 is not installed, your system continues to store log and spool files on the first disk drive. The second disk is defined into two partitions:

The first partition is the log partition and uses about 30 percent of the disk.

The second partition is the spool partition that uses 50percent of the disk.

Table 2-3 andTable 2-4 shows sample partition tables for disks 1 and 2 for a Netra t 1400 with18-GBdisk drives.

Table 2-318-GBDisk 1 Partition Table (Cisco PGW 2200 Softswitch with Log and Spool Package)

 

Cisco PGW 2200 Softswitch Host

 

Slice No.

 

 

Slice Name

Slice Size (GB)

 

 

 

0

/

1.00

 

 

 

1

/var

1.40

 

 

 

2

 

0.00

 

 

 

3

 

0.00

 

 

 

4

 

0.00

 

 

 

5

/opt

12.00

 

 

 

6

swap

2.00

 

 

 

7

 

0.00

 

 

 

Note On disk drives larger than 18 GB, the swap space is 4 GB.

Table 2-418-GBDisk 2 Partition Table (Cisco PGW 2200 Softswitch with Log and Spool Package)

 

 

 

 

 

Cisco PGW 2200 Softswitch Host

 

 

 

 

 

 

 

Slice No.

 

 

 

 

 

 

 

Slice Name

Slice Size (GB)

 

 

 

 

 

 

0

/

1.00

 

 

 

 

 

 

 

 

1

swap

2.00

 

 

 

 

 

 

 

 

2

 

0.00

 

 

 

 

 

 

 

 

3

/opt/CiscoMGC/var/log

5.70

 

 

 

 

 

 

 

 

4

/opt/CiscoMGC/var/spool

9.00

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

 

 

 

 

2-90

 

 

 

 

 

OL-18083-01

 

 

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

Table 2-4

18-GBDisk 2 Partition Table (Cisco PGW 2200 Softswitch with Log and Spool

 

Package) (continued)

 

 

 

 

5

 

0.00

 

 

 

 

 

6

 

0.00

 

 

 

 

 

7

 

0.00

 

 

 

 

 

Step 1 Load the Cisco Solaris 10 Operating Environment CD into theCD-ROMdrive. From the /var/tmp directory of the target machine, install the Log And Spool Software by entering the following command:

#cd /var/tmp

#pkgadd -d /cdrom/cdrom0/CSCOh024.pkg

Text similar to the following is displayed:

The

following

packages are available:

1

CSCOh024

Media Gateway Controller Log and Spool package

 

 

(sparc) 3.0(6)

Select package(s) you wish to process (or 'all' to process all packages). (default: all) [?,??,q]:

Note You can also download theSparc-basedlog and spool package (CSCOh024) from Cisco.com. For example, download the CSCOh024 package to the /opt/SW folder on theSparc-basedplatform and use the command, pkgadd-d /opt/SW/CSCOh024.pkg.

Step 2 PressEnter to accept the default answerall. Text similar to the following is displayed:

Processing package instance <CSCOh024 from </var/tmp/CSCOh024.pkg

Media Gateway Controller Log and Spool package(sparc) 3.0(6) Cisco Systems, Inc.

## Executing checkinstall script.

CSCOh024 checkinstall log file at /var/tmp/CSCOh024.checkinstall.log Platform is SUNW,Ultra-80

This machine is running Solaris 5.10

The selected base directory </opt/sun_install> must exist before installation is attempted.

Do you want this directory created now [y,n,?,q] y

Step 3 Answery and pressEnter to create the directory. Text similar to the following is displayed:

Using </opt/sun_install> as the package base directory.

##Processing package information.

##Processing system information.

1 package pathname is already properly installed.

##Verifying disk space requirements.

##Checking for conflicts with packages already installed.

The following files are already installed on the system and are being used by another package:

*/opt/sun_install <attribute change only>

*- conflict with a file which does not belong to any package.

Do you want to install these conflicting files [y,n,?,q]

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-91

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

Step 4 Answery and pressEnter to install the files. Text similar to the following is displayed:

## Checking for setuid/setgid programs.

This package contains scripts which will be executed with super-userpermission during the process of installing this package.

Do you want to continue with the installation of <CSCOh024> [y,n,?]

Step 5 Typey and pressEnter to continue. Text similar to the following is displayed:

Installing Media Gateway Controller Log and Spool package as <CSCOh024>

## Executing preinstall script. Platform is SUNW,Ultra-80

This is a known platform

NOTICE: Architecture checks passed

## Installing part 1 of 1. /opt/sun_install/format_log_spool_start.cmd /opt/sun_install/install_log_spool /opt/sun_install/query_2nd_disk.cmd

[ verifying class <none> ]

## Executing postinstall script.

!!

!!You must now change directories to /opt/sun_install/Log_Spool and

!!run the ./install_log_spool script as root.

!!

Step 6 Change directory to /opt/sun_install/Log_Spool and run the install_log_spool script.

Note You must first shut down the Cisco PGW 2200 Softswitch before running the install_log_spool script.

#cd /opt/sun_install/Log_Spool

#./install_log_spool

Text similar to the following is displayed:

Platform is SUNW,Ultra-80

Searching for disks...done

 

 

 

FORMAT MENU:

 

 

 

 

 

disk

- select a disk

 

 

 

type

- select (define) a disk type

 

 

 

partition

- select (define) a partition table

 

 

 

current

- describe the current disk

 

 

 

format

- format and analyze the disk

 

 

 

repair

- repair a defective sector

 

 

 

label

- write label to the disk

 

 

 

analyze

- surface analysis

 

 

 

defect

- defect list management

 

 

 

backup

- search for backup labels

 

 

 

verify

- read and display labels

 

 

 

save

- save new disk/partition definitions

 

 

 

volname

- set 8-charactervolume name

 

 

 

!<cmd>

- execute <cmd>, then return

 

 

 

quit

 

 

 

 

 

format> disk

 

 

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

2-92

 

 

OL-18083-01

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

AVAILABLE DISK SELECTIONS:

0.c0t0d0 <SUN36G cyl 24620 alt 2 hd 27 sec 107> /pci@1f,4000/scsi@3/sd@0,0

1.c0t1d0 <SUN36G cyl 24620 alt 2 hd 27 sec 107> /pci@1f,4000/scsi@3/sd@1,0

Specify disk (enter its number): 1 selecting c0t1d0

[disk formatted] format> current Current Disk = c0t1d0

<SUN36G cyl 24620 alt 2 hd 27 sec 107> /pci@1f,4000/scsi@3/sd@1,0

format> q

 

2nd Disk device is:

c0t1d0

Disk type is:

SUN36G

Number of Cylinders :

24620

Enter absolute path of the desired mount point for the log directory or press enter to accept

the default [/opt/CiscoMGC/var/log]:

Step 7 PressEnter to accept the default mount point for the log directory or change it if you plan on installing the Cisco PGW 2200 Softswitch software in a different location.

A screen similar to the following is displayed:

Log directory mount point is /opt/CiscoMGC/var/log

Enter absolute path of the desired mount point for the spool directory or press enter to accept

the default [/opt/CiscoMGC/var/spool]:

Step 8 PressEnter to accept the default mount point for the spool directory or change it if you plan on installing the Cisco PGW 2200 Softswitch software in a different location.

A screen similar to the following is displayed:

Spool directory mount point is /opt/CiscoMGC/var/spool

Number of cylinders for log partition: 9848

Start: 0

Start: 9847

Number of cylinders for spool partition: 14772

Start: 9848

Start: 24619

Build partition table for c0t1d0 ...

Searching for disks...done selecting c0t1d0

[disk formatted]

 

FORMAT MENU:

 

 

 

 

 

 

disk

- select a disk

 

type

- select (define) a disk type

 

partition

- select (define) a partition table

 

current

- describe the current disk

 

format

- format and analyze the disk

 

repair

- repair a defective sector

 

label

- write label to the disk

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-93

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

analyze

- surface analysis

defect

- defect list management

backup

- search for backup labels

verify

- read and display labels

save

- save new disk/partition definitions

inquiry

- show vendor, product and revision

volname

- set 8-charactervolume name

!<cmd>

- execute <cmd>, then return

quit

 

format> p

 

PARTITION MENU:

 

 

 

 

0

- change `0' partition

 

 

 

 

 

 

 

 

1

- change `1' partition

 

 

 

 

 

 

 

 

2

- change `2' partition

 

 

 

 

 

 

 

 

3

- change `3' partition

 

 

 

 

 

 

 

 

4

- change `4' partition

 

 

 

 

 

 

 

 

5

- change `5' partition

 

 

 

 

 

 

 

 

6

- change `6' partition

 

 

 

 

 

 

 

 

7

- change `7' partition

 

 

 

 

 

 

 

 

select - select a predefined table

 

 

 

 

 

 

 

 

modify

- modify a predefined partition table

 

 

 

 

 

 

 

name

- name the current table

 

 

 

 

 

 

 

 

print

- display the current table

 

 

 

 

 

 

 

 

label

- write partition map and label to the disk

 

 

 

 

 

 

!<cmd> - execute <cmd>, then return

 

 

 

 

 

 

 

 

quit

 

 

 

 

 

 

 

 

 

 

partition> 0

 

 

 

 

 

 

 

 

 

 

Part

Tag

Flag

Cylinders

Size

Blocks

 

 

0

root

wm

0 -

725

1.00GB

(726/0/0)

2097414

 

 

 

 

Enter partition id tag[root]: unassigned

 

 

 

 

 

 

 

Enter partition permission flags[wm]: wm

 

 

 

 

 

 

 

Enter new starting cyl[0]: 0

 

 

 

 

 

 

 

 

Enter partition size[2097414b, 726c, 1024.13mb, 1.00gb]: 0c

 

 

 

 

 

partition> 1

 

 

 

 

 

 

 

 

 

 

Part

Tag

Flag

Cylinders

Size

Blocks

 

 

1

swap

wu

726 -

3629

4.00GB

(2904/0/0)

8389656

 

 

 

 

Enter partition id tag[swap]: unassigned

 

 

 

 

 

 

 

Enter partition permission flags[wu]: wm

 

 

 

 

 

 

 

Enter new starting cyl[726]: 0

 

 

 

 

 

 

 

 

Enter partition size[8389656b, 2904c, 4096.51mb, 4.00gb]: 0c

 

 

 

 

 

partition> 3

 

 

 

 

 

 

 

 

 

 

Part

Tag

Flag

Cylinders

Size

Blocks

 

 

 

 

 

3 unassigned

wm

0

 

0

(0/0/0)

0

 

 

 

 

Enter partition id tag[unassigned]: unassigned

 

 

 

 

 

 

Enter partition permission flags[wm]: wm

 

 

 

 

 

 

 

Enter new starting cyl[0]: 0

 

 

 

 

 

 

 

 

Enter partition size[0b, 0c, 0.00mb, 0.00gb]: 0c

 

 

 

 

 

 

partition> 4

 

 

 

 

 

 

 

 

 

 

Part

Tag

Flag

Cylinders

Size

Blocks

 

 

 

 

 

4 unassigned

wm

3630 - 23156

26.90GB

(19527/0/0) 56413503

 

 

 

 

Enter partition id tag[unassigned]: unassigned

 

 

 

 

 

 

Enter partition permission flags[wm]: wm

 

 

 

 

 

 

 

Enter new starting cyl[3630]: 0

 

 

 

 

 

 

 

 

Enter partition size[56413503b, 19527c, 27545.66mb, 26.90gb]: 0c

 

 

 

 

 

partition> 5

 

 

 

 

 

 

 

 

 

 

Part

Tag

Flag

Cylinders

Size

Blocks

 

 

5

var

wm

23157 - 23882

1.00GB

(726/0/0)

2097414

 

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

 

 

 

 

2-94

 

 

 

 

 

 

 

 

OL-18083-01

 

 

 

 

 

 

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

Enter partition id tag[var]: unassigned

 

 

 

Enter partition permission

flags[wm]: wm

 

 

 

Enter new starting cyl[23157]: 0

 

 

 

Enter partition size[2097414b, 726c, 1024.13mb, 1.00gb]: 0c

 

partition> 6

 

 

 

 

 

 

 

Part

Tag

Flag

 

Cylinders

Size

Blocks

 

6

usr

wm

23883

- 24608

1.00GB

(726/0/0)

2097414

Enter partition id tag[usr]: unassigned

 

 

 

Enter partition permission

flags[wm]: wm

 

 

 

Enter new starting cyl[23883]: 0

 

 

 

Enter partition size[2097414b, 726c, 1024.13mb, 1.00gb]: 0c

 

partition> 7

 

 

 

 

 

 

 

Part

Tag

Flag

 

Cylinders

Size

Blocks

 

7

unassigned

wm

24609

- 24619

15.52MB

(11/0/0)

31779

Enter partition id tag[unassigned]: unassigned

 

 

Enter partition permission

flags[wm]: wm

 

 

 

Enter new starting cyl[24609]: 0

 

 

 

Enter partition size[31779b,

11c, 15.52mb, 0.02gb]: 0c

 

 

partition> 2

 

 

 

 

 

 

 

Part

Tag

Flag

 

Cylinders

Size

Blocks

 

2

backup

wm

 

0

- 24619

33.92GB

(24620/0/0) 71127180

Enter partition id tag[backup]: unassigned

 

 

 

Enter partition permission

flags[wm]: wm

 

 

 

Enter new starting cyl[0]:

0

 

 

 

 

Enter partition size[71127180b, 24620c, 34730.07mb, 33.92gb]: 24620c

partition> 3

 

 

 

 

 

 

 

Part

Tag

Flag

 

Cylinders

Size

Blocks

 

3

unassigned

wm

 

0

 

0

(0/0/0)

0

Enter partition id tag[unassigned]: unassigned

 

 

Enter partition permission

flags[wm]: wm

 

 

 

Enter new starting cyl[0]:

0

 

 

 

 

Enter partition size[0b, 0c,

0.00mb, 0.00gb]: 9848c

 

 

partition> 4

 

 

 

 

 

 

 

Part

Tag

Flag

 

Cylinders

Size

Blocks

 

4

unassigned

wm

 

0

 

0

(0/0/0)

0

Enter partition id tag[unassigned]: unassigned

 

 

Enter partition permission

flags[wm]: wm

 

 

 

Enter new starting cyl[0]:

9848

 

 

 

Enter partition size[0b, 0c,

0.00mb, 0.00gb]: 14772c

 

 

partition> p

 

 

 

 

 

 

 

Current partition table (unnamed):

 

 

 

Total disk cylinders available: 24620 + 2 (reserved cylinders)

 

Part

Tag

Flag

 

Cylinders

Size

Blocks

 

0

unassigned

wm

 

0

 

0

(0/0/0)

0

1

unassigned

wm

 

0

 

0

(0/0/0)

0

2

unassigned

wm

 

0

- 24619

33.92GB

(24620/0/0)

71127180

3

unassigned

wm

 

0

- 9847

13.57GB

(9848/0/0)

28450872

4

unassigned

wm

9848

- 24619

20.35GB

(14772/0/0) 42676308

5

unassigned

wm

 

0

 

0

(0/0/0)

0

6

unassigned

wm

 

0

 

0

(0/0/0)

0

7

unassigned

wm

 

0

 

0

(0/0/0)

0

partition> l

partition> q

FORMAT MENU:

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-95

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

 

 

disk

 

-

select a disk

 

 

 

 

 

 

 

type

 

-

select (define) a disk type

 

 

 

 

 

partition

-

select (define) a partition table

 

 

 

 

current

-

describe the current disk

 

 

 

 

 

format

-

format and analyze the disk

 

 

 

 

 

repair

-

repair a defective sector

 

 

 

 

 

label

-

write label to the disk

 

 

 

 

 

 

analyze

-

surface analysis

 

 

 

 

 

 

defect

-

defect list management

 

 

 

 

 

 

backup

-

search for backup labels

 

 

 

 

 

verify

-

read and display labels

 

 

 

 

 

 

save

 

-

save new disk/partition definitions

 

 

 

 

inquiry

-

show vendor, product and revision

 

 

 

 

volname

-

set 8-charactervolume name

 

 

 

 

 

!<cmd>

-

execute <cmd>, then return

 

 

 

 

 

quit

 

 

 

 

 

 

 

 

 

format>

q

 

 

 

 

 

 

 

 

 

unknown

disk type,

assuming the speed is 10000 rpm

 

 

 

Build log filesystem

at /dev/rdsk/c0t1d0s3 ...

 

 

 

mkfs -F

ufs /dev/rdsk/c0t1d0s3 28450872 107 27 8192 1024 251 1 166 8192 t 0 -18 107

Cylinder groups must

have a multiple of 16 cylinders with the given parameters

Rounded

cgsize up to

256

 

 

 

 

 

 

/dev/rdsk/c0t1d0s3:

 

28450872 sectors in 9848 cylinders of 27 tracks, 107 sectors

 

 

13892.0MB in

308 cyl groups (32 c/g, 45.14MB/g, 5632 i/g)

 

super-blockbackups (for fsck-Fufs-ob=#) at:

 

 

 

32,

92592,

185152,

 

277712,

370272,

462832,

555392,

647952,

740512,

833072,

.

 

 

 

 

 

 

 

 

 

 

 

.

 

 

 

 

 

 

 

 

 

 

 

.

 

 

 

 

 

 

 

 

 

 

 

Build spool filesystem at /dev/rdsk/c0t1d0s4 ...

 

 

 

mkfs -F

ufs /dev/rdsk/c0t1d0s4 42676308 107 27 8192 1024 251 1 166 8192 t 0 -18 107

Cylinder groups must

have a multiple of 16 cylinders with the given parameters

Rounded

cgsize up to

256

 

 

 

 

 

 

/dev/rdsk/c0t1d0s4:

 

42676308 sectors in 14772 cylinders of 27 tracks, 107 sectors

 

 

20838.0MB in

462 cyl groups (32 c/g, 45.14MB/g, 5632 i/g)

 

super-blockbackups (for fsck-Fufs-ob=#) at:

 

 

 

32,

92592,

185152,

 

277712,

370272,

462832,

555392,

647952,

740512,

833072,

.

 

 

 

 

 

 

 

 

 

 

 

.

 

 

 

 

 

 

 

 

 

 

 

.

 

 

 

 

 

 

 

 

 

 

 

Remove any existing entry in /etc/vfstab for c0t1d0s3 or c0t1d0s4

Adding entries to /etc/vfstab

Mounting /opt/CiscoMGC/var/log

Mounting /opt/CiscoMGC/var/spool

Success!!!

This completes the installation of the Log and Spool File system. Go to Table 2-2 on page 2-72 if you want to continue with the list for package installation.

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-96

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

Uninstalling the Log and Spool File System

Use the following procedure if you need to remove the Log and Spool File system from the second disk. Contact Cisco TAC if you need assistance (see the “Obtaining Documentation and Submitting a Service Request” section in thePreface).

Note You must be logged in asroot to uninstall CSCOh024.

Step 1 Type the following command at the# prompt and pressEnter:

cd /opt/sun_install/Log_Spool/

./uninstall_log_spool

Text similar to the following is displayed:

You are running as root - Good...

***WARNING! LOG FILES WILL NOT BE SAVED ***

Uninstalling this package typically means that the log & spool directories will be on the same disk as the rest of the software so there is less space available for those files. We will not save any existing log or spool files.

***WARNING! LOG FILES WILL NOT BE SAVED ***

However, they are not being deleted - the log files will still exist on the second (unmounted) disk drive

It is possible to manually mount that disk and recover log files if necessary.

 

If you want to save log files before running this

 

script, then exit and do so now

 

Do you want to continue? (y/n) [N] y

Step 2

Type y and pressEnter to remove CSCOh024. Text similar to the following is displayed:

 

Unmount /opt/CiscoMGC/var/log

 

Unmount /opt/CiscoMGC/var/spool

 

Update /etc/vfstab

 

Remove old files...

 

The Log/Spool software has been removed from the system

 

Now you can remove the package with the command:

 

pkgrm CSCOh024

 

Done!

Step 3

Type the following command and press Enter to continue the removal of CSCOh024.

 

pkgrm CSCOh024

Step 4

Reboot your machine with the -r option. Type the following command and pressEnter:

 

# reboot--–r

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-97

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

Note If you have installed the Solaris DiskSuite package (CSCOh023) on your system, the messages below are displayed during system boot. They are normal Solaris DiskSuite startup messages and do not indicate any problem with your system.

WARNING force load of misc /md-transfailed

WARNING force load of misc /md-raidfailed

WARNING force load of misc /md-hotsparesfailed

WARNING force load of misc /md-spfailed

This completes the removal of the Log and Spool File system from the second disk.

Installing Cisco BAMS Archive Partition (CSCOh027)

The Cisco BAMS application cannot use the Solstice DiskSuite to configure the local disk drives. Use the procedure below to create an archive partition on the disk drives for Cisco BAMS systems.

Note You must log in asroot to run the following installation script.

Step 1 Load the Cisco Solaris 10 Operating Environment CD into theCD-ROMdrive. Enter the following command to install the Cisco BAMS disk configuration scripts:

pkgadd -d /cdrom/cdrom0/CSCOh027.pkg

Text similar to the following is displayed.

The

following

packages are available:

1

CSCOh027

Media Gateway Controller BAMS Archive Partition Package

 

 

(sparc) 3.0(6)

Select package(s) you wish to process (or 'all' to process all packages). (default: all) [?,??,q]:

 

 

 

 

Note

You can also download the Sparc-basedCisco BAMS archive partition package (CSCOh027)

 

 

 

 

 

from Cisco.com. For example, download the CSCOh027 package to the /opt/SW folder on the

 

 

 

 

 

Sparc-basedplatform and use the command, pkgadd-d /opt/SW/CSCOh027.pkg.

 

 

 

 

 

 

 

 

 

Step 2

Press Enter to accept the default answerall.

 

 

 

 

Text similar to the following is displayed:

 

 

 

 

Processing package instance <CSCOh027> from </var/tmp/CSCOh027.pkg>

 

 

 

 

Media Gateway Controller BAMS Archive Partition Package(sparc) 3.0(6)

 

 

 

 

Cisco Systems, Inc.

 

 

 

 

## Executing checkinstall script.

 

 

 

 

CSCOh027 checkinstall log file at /var/tmp/CSCOh027.checkinstall.log

 

 

 

 

Platform is SUNW,Sun-Fire-V210

 

 

 

 

This machine is running Solaris 5.10

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

2-98

 

 

 

OL-18083-01

 

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

The selected base directory </opt/sun_install> must exist before installation is attempted.

Do you want this directory created now [y,n,?,q]

Step 3 Answery and pressEnter to create the directory.

Text similar to the following is displayed:

Using </opt/sun_install> as the package base directory.

##Processing package information.

##Processing system information.

1 package pathname is already properly installed.

##Verifying disk space requirements.

##Checking for conflicts with packages already installed.

The following files are already installed on the system and are being used by another package:

*/opt/sun_install <attribute change only>

*- conflict with a file which does not belong to any package.

Do you want to install these conflicting files [y,n,?,q] y

Step 4 Answery and pressEnter to install the files.

Text similar to the following is displayed:

## Checking for setuid/setgid programs.

This package contains scripts which will be executed with super-userpermission during the process of installing this package.

Do you want to continue with the installation of <CSCOh027> [y,n,?]

Step 5 Typey and pressEnter to continue the installation.

Text similar to the following is displayed:

Installing Media Gateway Controller BAMS Archive Partition Package as <CSCOh027>

##Installing part 1 of 1. [ verifying class <none> ]

##Executing postinstall script.

!!

!!You must now change directories to

!!/opt/sun_install/BAMS_archive and run the

!!./install_BAMS_archive script as root.

!!

Installation of <CSCOh027> was successful.

Step 6 Change directories. Enter the following command:

cd /opt/sun_install/BAMS_archive

Step 7 Run the first script. Enter the following command:

./install_BAMS_archive.sh

Text similar to the following is displayed:

Output will be logged in /opt/sun_install/BAMS_archive/install_BAMS_archive.log

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-99

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

The second hard drive will be reformatted by this script, all data on this drive will be lost

Do you want to continue with formatting? (y or n)

Installation started on Wed Jul 9 20:54:33 EDT 2008

Platform is SUNW,Sun-Fire-V210

Searching for disks...done

FORMAT MENU:

 

disk

- select a disk

type

- select (define) a disk type

partition

- select (define) a partition table

current

- describe the current disk

format

- format and analyze the disk

fdisk

- run the fdisk program

repair

- repair a defective sector

label

- write label to the disk

analyze

- surface analysis

defect

- defect list management

backup

- search for backup labels

verify

- read and display labels

volname

- set 8-charactervolume name

!<cmd>

- execute <cmd>, then return

quit

 

format> disk

 

AVAILABLE DISK SELECTIONS:

0.c1t0d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> /pci@1c,600000/scsi@2/sd@0,0

1.c1t1d0 <SUN72G cyl 14087 alt 2 hd 24 sec 424> /pci@1c,600000/scsi@2/sd@1,0

Specify disk (enter its number): 1 selecting c1t1d0

[disk formatted] format> current Current Disk = c1t1d0

<SUN72G cyl 14087 alt 2 hd 24 sec 424> /pci@1c,600000/scsi@2/sd@1,0

format> q

 

2nd Disk device is:

c1t1d0

Disk type is:

SUN72G

Number of Cylinders :

14087

ARCHIVE directory mount point is /opt/CiscoBAMS/CDR/archive

Number of cylinders for archive partition:

14087

Building format log temp files...

Build partition table for c1t1d0 ...

Searching for disks...done

selecting c1t1d0

[disk formatted]

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-100

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

FORMAT MENU:

 

disk

- select a disk

type

- select (define) a disk type

partition

- select (define) a partition table

current

- describe the current disk

format

- format and analyze the disk

repair

- repair a defective sector

label

- write label to the disk

analyze

- surface analysis

defect

- defect list management

backup

- search for backup labels

verify

- read and display labels

save

- save new disk/partition definitions

inquiry

- show vendor, product and revision

volname

- set 8-charactervolume name

!<cmd>

- execute <cmd>, then return

quit

 

format> p

 

PARTITION MENU:

 

0

- change

`0' partition

 

 

 

 

1

- change

`1' partition

 

 

 

 

2

- change

`2' partition

 

 

 

 

3

- change

`3' partition

 

 

 

 

4

- change

`4' partition

 

 

 

 

5

- change

`5' partition

 

 

 

 

6

- change

`6' partition

 

 

 

 

7

- change

`7' partition

 

 

 

 

select - select

a predefined table

 

 

 

 

modify

- modify

a predefined partition table

 

 

 

name

- name the current table

 

 

 

 

print

- display the current table

 

 

 

 

label

- write partition map and label to the disk

 

 

!<cmd> - execute <cmd>, then return

 

 

 

 

quit

 

 

 

 

 

 

partition> 0

 

 

 

 

 

 

Part

Tag

Flag

Cylinders

Size

Blocks

 

0

root

wm

806 -

1208

1.96GB

(403/0/0)

4100928

Enter partition id tag[root]: unassigned

 

 

 

Enter partition permission flags[wm]: wm

 

 

 

Enter new starting cyl[806]: 0

 

 

 

 

Enter partition size[4100928b, 403c, 402e, 2002.41mb, 1.96gb]: 0c

 

partition> 1

 

 

 

 

 

 

Part

Tag

Flag

Cylinders

Size

Blocks

 

1

var

wm

1209 -

2215

4.89GB

(1007/0/0)

10247232

 

Enter partition id tag[var]: unassigned

 

 

 

 

 

 

 

 

Enter partition permission flags[wm]: wm

 

 

 

 

 

 

 

 

Enter new starting cyl[1209]: 0

 

 

 

 

 

 

 

 

 

Enter partition size[10247232b, 1007c, 1006e, 5003.53mb, 4.89gb]: 0c

 

 

 

 

 

 

partition> 3

 

 

 

 

 

 

 

 

 

 

 

Part

Tag

Flag

Cylinders

Size

Blocks

 

 

 

 

 

3

swap

wu

0 -

805

3.91GB

(806/0/0)

8201856

 

 

 

 

 

Enter partition id tag[swap]: unassigned

 

 

 

 

 

 

 

 

Enter partition permission flags[wu]: wm

 

 

 

 

 

 

 

 

Enter new starting cyl[0]: 0

 

 

 

 

 

 

 

 

 

Enter partition size[8201856b, 806c, 805e, 4004.81mb, 3.91gb]: 0c

 

 

 

 

 

 

partition> 4

 

 

 

 

 

 

 

 

 

 

 

Part

Tag

Flag

Cylinders

Size

Blocks

 

 

 

 

 

 

4 unassigned

wm

2216 -

2220

24.84MB

(5/0/0)

50880

 

 

 

 

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

 

OL-18083-01

 

 

 

 

 

 

 

 

2-101

 

 

 

 

 

 

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

Enter partition id tag[unassigned]: unassigned

 

Enter partition permission flags[wm]: wm

 

 

Enter new starting cyl[2216]: 0

 

 

Enter partition size[50880b, 5c, 4e, 24.84mb, 0.02gb]: 0c

partition> 5

 

 

 

 

Part

Tag

Flag

Cylinders

Size

Blocks

5 unassigned

wm

2221 - 13683

55.62GB

(11463/0/0) 116647488

Enter partition id tag[unassigned]: unassigned Enter partition permission flags[wm]: wm

Enter new starting cyl[2221]: 0

Enter partition size[116647488b, 11463c, 11462e, 56956.78mb, 55.62gb]: 0c partition> 6

Part

Tag

Flag

Cylinders

Size

Blocks

 

6 unassigned

wm

13684 - 14086

1.96GB

(403/0/0)

4100928

Enter partition id tag[unassigned]: unassigned

 

 

Enter partition permission flags[wm]: wm

 

 

 

Enter new starting cyl[13684]: 0

 

 

 

Enter partition size[4100928b, 403c, 402e, 2002.41mb, 1.96gb]: 0c

 

partition> 7

 

 

 

 

 

Part

Tag

Flag

Cylinders

Size

Blocks

 

7 unassigned

wm

0

0

(0/0/0)

0

Enter partition id tag[unassigned]: unassigned

 

 

Enter partition permission flags[wm]: wm

 

 

 

Enter new starting cyl[0]: 0

 

 

 

Enter partition size[0b, 0c, 0e, 0.00mb, 0.00gb]: 0c

 

 

partition> 2

 

 

 

 

 

Part

Tag

Flag

Cylinders

Size

Blocks

 

2

backup

wm

0 - 14086

68.35GB

(14087/0/0) 143349312

Enter partition id tag[backup]: backup Enter partition permission flags[wm]: wm Enter new starting cyl[0]:

Enter partition size[143349312b, 14087c, 14086e, 69994.78mb, 68.35gb]: 14087c partition> 0

Part

Tag

Flag

Cylinders

Size

Blocks

 

0

unassigned

wm

0

 

0

(0/0/0)

0

Enter partition id tag[unassigned]: unassigned

 

 

Enter partition permission

flags[wm]: wm

 

 

 

Enter new starting cyl[0]:

 

 

 

 

 

Enter partition size[0b, 0c,

0e, 0.00mb, 0.00gb]: 14087c

 

partition> p

 

 

 

 

 

 

Current partition

table (unnamed):

 

 

 

Total disk cylinders available: 14087 + 2 (reserved cylinders)

 

Part

Tag

Flag

Cylinders

Size

Blocks

 

0

unassigned

wm

0

- 14086

68.35GB

(14087/0/0) 143349312

1

unassigned

wm

0

 

0

(0/0/0)

0

2

backup

wm

0

- 14086

68.35GB

(14087/0/0) 143349312

3

unassigned

wm

0

 

0

(0/0/0)

0

4

unassigned

wm

0

 

0

(0/0/0)

0

5

unassigned

wm

0

 

0

(0/0/0)

0

6

unassigned

wm

0

 

0

(0/0/0)

0

7

unassigned

wm

0

 

0

(0/0/0)

0

partition> l

partition> q

FORMAT MENU:

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-102

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

disk

- select a disk

type

- select (define) a disk type

partition

- select (define) a partition table

current

- describe the current disk

format

- format and analyze the disk

repair

- repair a defective sector

label

- write label to the disk

analyze

- surface analysis

defect

- defect list management

backup

- search for backup labels

verify

- read and display labels

save

- save new disk/partition definitions

inquiry

- show vendor, product and revision

volname

- set 8-charactervolume name

!<cmd>

- execute <cmd>, then return

quit

 

format> q

 

Build archive filesystem at /dev/rdsk/c1t1d0s0 ...

Remove any existing entry in /etc/vfstab for c1t1d0

Adding entries to /etc/vfstab

Mounting /opt/CiscoBAMS/CDR/archive

Success!!!

The Cisco BAMS archive partition installation is now complete. If you want to return to the list for package installation, go to Table 2-2 on page 2-72.

Installing the Sparc-basedCommunications and Alarm Software Package (CSCOh026)

This package installs xterm, ntp, and ftp communications software on your host. It also installs the Lights Out Management (LOM) alarm software package if you are installing Solaris 10 on one of the following platforms:

Sun Fire V120

Netra 120

Netra t 1120/1125

Netra t 1400/1405

Netra 20

If you are installing Solaris 10 on a Sun Fire V210, Netra 210, Netra 240 or Netra 440 platform, there are no separate alarm software packages to install because the alarm software is installed automatically. This software, ALOM, is integrated within the Solaris 10 operating system. Therefore, previous SUN LOM alarm packages like SUNWlomm (on Sun Fire V120) and SUNWtsalm (on Netra 112X) do not exist on these platforms. For additional information regarding lights-outalarms on the Sun Fire V210, Netra 210, Netra 240 and Netra 440, see theSUN ALOM Guide at http://www.sun.com/servers/alom.html.

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-103

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

Note The installation of this package does not automatically enable ftp communications on your host. If you are installing this software on a Cisco BAMS system or if your host requires that the ftp communications be enabled, you can find instructions for enabling ftp in Step 5 of this procedure.

To install the communications and alarm software on your hosts, perform the following steps:

Step 1 Load the Cisco Solaris 10 Operating Environment CD into theCD-ROMdrive. Install this package by entering the following command at the # prompt:

#pkgadd -d /cdrom/cdrom0/CSCOh026.pkg

Text similar to the following is displayed along with copyright and trademark information:

The

following

packages are available:

1

CSCOh026

Media Gateway Controller PGW Specific Solaris 10 packages

 

 

(sparc) 3.0(6)

Select package(s) you wish to process (or 'all' to process all packages). (default: all) [?,??,q]:

Note You can also download theSparc-basedcommunications and alarm software package (CSCOh026) from Cisco.com. For example, download the CSCOh026 package to the /opt/SW folder on theSparc-basedplatform and use the command, pkgadd-d /opt/SW/CSCOh026.pkg.

Step 2 PressEnter to accept the default answer ofall and install all the packages. Text similar to the following is displayed:

Processing package instance <CSCOh026> from </var/tmp/CSCOh026.pkg>

Media Gateway Controller PGW Specific Solaris 10 packages(sparc) 3.0(6) Cisco Systems, Inc.

## Executing checkinstall script.

CSCOh026 checkinstall log file at /var/tmp/CSCOh026.checkinstall.log Platform is SUNW,Sun-Fire-V210

This machine is running Solaris 5.10

Using </opt/sun_install> as the package base directory.

##Processing package information.

##Processing system information.

2 package pathnames are already properly installed.

##Verifying disk space requirements.

##Checking for conflicts with packages already installed.

##Checking for setuid/setgid programs.

This package contains scripts which will be executed with super-userpermission during the process of installing this package.

Do you want to continue with the installation of <CSCOh026> [y,n,?]

Step 3 Typey and pressEnter to continue the installation. Text similar to the following is displayed:

Installing Media Gateway Controller PGW Specific Solaris 10 packages as <CSCOh026>

## Installing part 1 of 1. /opt/sun_install/SolPkg/137324-01.zip /opt/sun_install/SolPkg<implied directory> /opt/sun_install/SolPkg/LOM20.tar.gz /opt/sun_install/SolPkg/SUNWftpr.tar.gz /opt/sun_install/SolPkg/SUNWftpu.tar.gz

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-104

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

/opt/sun_install/SolPkg/SUNWnfsckr.tar.gz /opt/sun_install/SolPkg/SUNWnfscr.tar.gz /opt/sun_install/SolPkg/SUNWnfscu.tar.gz /opt/sun_install/SolPkg/SUNWnfsskr.tar.gz /opt/sun_install/SolPkg/SUNWnfssr.tar.gz /opt/sun_install/SolPkg/SUNWnfssu.tar.gz /opt/sun_install/SolPkg/SUNWtftp.tar.gz /opt/sun_install/SolPkg/SUNWtftpr.tar.gz /opt/sun_install/SolPkg/SUNWvts.tar.gz /opt/sun_install/SolPkg/SUNWvtsmn.tar.gz /opt/sun_install/SolPkg/SUNWvtsr.tar.gz /opt/sun_install/SolPkg/SUNWvtsts.tar.gz /opt/sun_install/SolPkg/SUNWxwopt.tar.gz /opt/sun_install/SolPkg/autoinspkg /opt/sun_install/SolPkg/autoremovevts /opt/sun_install/SolPkg/configNtp.sh /opt/sun_install/SolPkg/gunzip /opt/sun_install/SolPkg/install_SolPkg.sh /opt/sun_install/SolPkg/ntp_Sparc.tar.gz /opt/sun_install/SolPkg/uninstall_SolPkg.sh [ verifying class <none> ]

## Executing postinstall script.

!!

!!You must now change directories to

!!/opt/sun_install/SolPkg and run the

!!./install_SolPkg.sh script as root.

Installation of <CSCOh026> was successful.

Step 4 Enter the following commands to change directories and execute the installation script.

cd /opt/sun_install/SolPkg

./install_SolPkg.sh

Text similar to the following is displayed:

Note The following command output is truncated. These lists vary over time.

You are running as root - Good...

x ./SUNWxwopt, 0 bytes, 0 tape blocks

x ./SUNWxwopt/archive, 0 bytes, 0 tape blocks

x ./SUNWxwopt/archive/none.bz2, 625965 bytes, 1223 tape blocks x ./SUNWxwopt/install, 0 bytes, 0 tape blocks

x ./SUNWxwopt/install/copyright, 93 bytes, 1 tape blocks x ./SUNWxwopt/install/depend, 344 bytes, 1 tape blocks

x ./SUNWxwopt/install/i.none, 2245 bytes, 5 tape blocks x ./SUNWxwopt/pkginfo, 473 bytes, 1 tape blocks

x ./SUNWxwopt/pkgmap, 4506 bytes, 9 tape blocks x ./SUNWxwopt/reloc, 0 bytes, 0 tape blocks

 

 

x ./SUNWxwopt/reloc/openwin, 0 bytes, 0 tape blocks

 

 

x ./SUNWxwopt/reloc/openwin/bin, 0 bytes, 0 tape blocks

 

 

x ./SUNWxwopt/reloc/openwin/lib, 0 bytes, 0 tape blocks

 

 

x ./SUNWxwopt/reloc/openwin/lib/app-defaults,0 bytes, 0 tape blocks

 

 

x ./SUNWxwopt/reloc/openwin/lib/X11, 0 bytes, 0 tape blocks

 

 

x ./SUNWxwopt/reloc/openwin/lib/X11/twm, 0 bytes, 0 tape blocks

 

 

x ./SUNWxwopt/reloc/openwin/lib/X11/xdm, 0 bytes, 0 tape blocks

 

 

spawn pkgadd -d .SUNWxwopt

 

 

Processing package instance <SUNWxwopt> from </tmp>

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-105

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

X Window System

Optional Clients(sparc) 6.6.2.7400,REV=0.2004.12.15

Copyright 2005

Sun Microsystems, Inc. All rights reserved.

Use is subject

to license terms.

Using </usr> as

the package base directory.

##Processing package information.

##Processing system information.

6 package pathnames are already properly installed.

##Verifying package dependencies.

##Verifying disk space requirements.

##Checking for conflicts with packages already installed.

##Checking for setuid/setgid programs.

This package contains scripts which will be executed with super-userpermission during the process of installing this package.

Do you want to continue with the installation of <SUNWxwopt> [y,n,?] y

Installing X Window System Optional Clients as <SUNWxwopt>

## Installing part 1 of 1. 3379 blocks

Installation of <SUNWxwopt> was successful.

x ./SUNWftpr, 0 bytes, 0 tape blocks

x ./SUNWftpr/install, 0 bytes, 0 tape blocks

x ./SUNWftpr/install/copyright, 93 bytes, 1 tape blocks x ./SUNWftpr/install/depend, 1036 bytes, 3 tape blocks

x ./SUNWftpr/install/i.ftpaccess, 2849 bytes, 6 tape blocks x ./SUNWftpr/install/i.ftpusers, 1506 bytes, 3 tape blocks x ./SUNWftpr/install/i.manifest, 1503 bytes, 3 tape blocks x ./SUNWftpr/install/i.preserve, 186 bytes, 1 tape blocks x ./SUNWftpr/install/r.manifest, 1044 bytes, 3 tape blocks x ./SUNWftpr/pkginfo, 452 bytes, 1 tape blocks

x ./SUNWftpr/pkgmap, 982 bytes, 2 tape blocks x ./SUNWftpr/reloc, 0 bytes, 0 tape blocks

x ./SUNWftpr/reloc/etc, 0 bytes, 0 tape blocks

x ./SUNWftpr/reloc/etc/ftpd, 0 bytes, 0 tape blocks

x ./SUNWftpr/reloc/etc/ftpd/ftpaccess, 1518 bytes, 3 tape blocks

x ./SUNWftpr/reloc/etc/ftpd/ftpconversions, 946 bytes, 2 tape blocks x ./SUNWftpr/reloc/etc/ftpd/ftpgroups, 104 bytes, 1 tape blocks

x ./SUNWftpr/reloc/etc/ftpd/ftphosts, 108 bytes, 1 tape blocks

x ./SUNWftpr/reloc/etc/ftpd/ftpservers, 114 bytes, 1 tape blocks x ./SUNWftpr/reloc/etc/ftpd/ftpusers, 198 bytes, 1 tape blocks

x ./SUNWftpr/reloc/var, 0 bytes, 0 tape blocks

x ./SUNWftpr/reloc/var/svc, 0 bytes, 0 tape blocks

x ./SUNWftpr/reloc/var/svc/manifest, 0 bytes, 0 tape blocks

x ./SUNWftpr/reloc/var/svc/manifest/network, 0 bytes, 0 tape blocks

x ./SUNWftpr/reloc/var/svc/manifest/network/ftp.xml, 1779 bytes, 4 tape blocks spawn pkgadd -d .SUNWftpr

Processing package instance <SUNWftpr> from </tmp>

FTP Server, (Root)(sparc) 11.10.0,REV=2005.01.21.15.53

Copyright 2005 Sun Microsystems, Inc. All rights reserved.

Use is subject to license terms.

Using </> as the package base directory.

##Processing package information.

##Processing system information.

5 package pathnames are already properly installed.

##Verifying package dependencies.

##Verifying disk space requirements.

##Checking for conflicts with packages already installed.

##Checking for setuid/setgid programs.

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-106

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

This package contains scripts which will be executed with super-userpermission during the process of installing this package.

Do you want to continue with the installation of <SUNWftpr> [y,n,?] y

Installing FTP Server, (Root) as <SUNWftpr>

## Installing part 1 of 1. [ verifying class <none> ]

[ verifying class <preserve> ] [ verifying class <ftpaccess> ] [ verifying class <ftpusers> ] y

[ verifying class <manifest> ]

Installation of <SUNWftpr> was successful.

x ./SUNWftpu, 0 bytes, 0 tape blocks

x ./SUNWftpu/archive, 0 bytes, 0 tape blocks

x ./SUNWftpu/archive/none.bz2, 119958 bytes, 235 tape blocks x ./SUNWftpu/install, 0 bytes, 0 tape blocks

x ./SUNWftpu/install/copyright, 8644 bytes, 17 tape blocks x ./SUNWftpu/install/depend, 1130 bytes, 3 tape blocks

x ./SUNWftpu/install/i.none, 2245 bytes, 5 tape blocks x ./SUNWftpu/pkginfo, 495 bytes, 1 tape blocks

x ./SUNWftpu/pkgmap, 673 bytes, 2 tape blocks x ./SUNWftpu/reloc, 0 bytes, 0 tape blocks

x ./SUNWftpu/reloc/usr, 0 bytes, 0 tape blocks

x ./SUNWftpu/reloc/usr/sbin, 0 bytes, 0 tape blocks spawn pkgadd -d .SUNWftpu

Processing package instance <SUNWftpu> from </tmp>

FTP Server, (Usr)(sparc) 11.10.0,REV=2005.01.21.15.53

Copyright 2001-2003Sun Microsystems, Inc. All rights reserved.

Use is subject to license terms.

Copyright (c) 1999,2000,2001 WU-FTPDDevelopment Group. All rights reserved.

WU-FTPDSOFTWARE LICENSE

Use, modification, or redistribution (including distribution of any modified or derived work) in any form, or on any medium, is permitted only if all the following conditions are met:

1.Redistributions qualify as "freeware" or "Open Source Software" under the following terms:

a.Redistributions are made at no charge beyond the reasonable cost of materials and delivery. Where redistribution of this software is as part of a larger package or combined work, this restriction applies only to the costs of materials and delivery of this

software, not to any other costs associated with the larger package or combined work.

b.Redistributions are accompanied by a copy of the Source Code or by an irrevocable offer to provide a copy of the Source Code for up to three years at the cost of materials and delivery. Such redistributions must allow further use, modification, and redistribution of the Source Code under substantially the same terms as this license. For the purposes of redistribution "Source Code" means all files included in the original distribution,

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-107

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

including all modifications or additions, on a medium and in a form allowing fully working executable programs to be produced.

2.Redistributions of Source Code must retain the copyright notices as they appear in each Source Code file and the COPYRIGHT file, these license terms, and the disclaimer/limitation of liability set forth as paragraph 6 below.

3.Redistributions in binary form must reproduce the Copyright Notice, these license terms, and the disclaimer/limitation of liability set forth as paragraph 6 below, in the documentation and/or other materials provided with the distribution. For the purposes of binary distribution the "Copyright Notice" refers to the following language:

Copyright (c) 1999,2000 WU-FTPDDevelopment Group.

All rights reserved.

Portions Copyright (c) 1980, 1985, 1988, 1989, 1990, 1991, 1993, 1994

The Regents of the University of California.

Portions Copyright (c) 1993, 1994 Washington University in Saint Louis.

Portions Copyright (c) 1996, 1998 Berkeley Software Design, Inc.

Portions Copyright (c) 1983, 1995, 1996, 1997 Eric P. Allman.

Portions Copyright (c) 1998 Sendmail, Inc.

Portions Copyright (c) 1989 Massachusetts Institute of Technology.

Portions Copyright (c) 1997 Stan Barber.

Portions Copyright (c) 1997 Kent Landfield.

Portions Copyright (c) 1991, 1992, 1993, 1994, 1995, 1996, 1997

Free Software Foundation, Inc.

Use and distribution of this software and its source code are governed by the terms and conditions of the WU-FTPDSoftware License ("LICENSE").

If you did not receive a copy of the license, it may be obtained online at http://www.wu-ftpd.org/license.html

4.All advertising materials mentioning features or use of this software must display the following acknowledgement: "This product includes software developed by the WU-FTPDDevelopment Group, the Washington University at Saint Louis, Berkeley Software Design, Inc., and their contributors."

5.Neither the name of the WU-FTPDDevelopment Group, nor the names of any copyright holders, nor the names of any contributors may be used to endorse or promote products derived from this software without specific prior written permission. The names "wuftpd" and"wu-ftpd"are trademarks of theWU-FTPDDevelopment Group and the Washington University at Saint Louis.

6.Disclaimer/Limitation of Liability:

THIS SOFTWARE IS PROVIDED BY THE WU-FTPDDEVELOPMENT GROUP, THE COPYRIGHT HOLDERS, AND CONTRIBUTORS, "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THEWU-FTPDDEVELOPMENT GROUP, THE COPYRIGHT HOLDERS, OR CONTRIBUTORS, BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-108

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

7.USE, MODIFICATION, OR REDISTRIBUTION, OF THIS SOFTWARE IMPLIES ACCEPTANCE OF ALL TERMS AND CONDITIONS OF THIS LICENSE.

$Id: LICENSE,v 1.4 2000/07/01 17:42:15 wuftpd Exp $

Copyright (c) 1993, 1994 Washington University in Saint Louis

All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. All advertising materials mentioning features or use of this software must display the following acknowledgement: This product includes software developed by the Washington University in Saint Louis and its contributors. 4. Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY WASHINGTON UNIVERSITY AND CONTRIBUTORS ``AS IS'' AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL WASHINGTON UNIVERSITY OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;

LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.

Copyright (c) 1980, 1983, 1985, 1988, 1989, 1990 Regents of the University of

California. All rights reserved.

Redistribution and use in source and binary forms, with or without modification, are permitted provided that the following conditions are met:

1.Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer.

2.Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution.

3.All advertising materials mentioning features or use of this software must display the following acknowledgement:

This product includes software developed by the University of California, Berkeley and its contributors.

4.Neither the name of the University nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.

THIS SOFTWARE IS PROVIDED BY THE REGENTS AND CONTRIBUTORS ``AS IS'' AND

ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE

ARE DISCLAIMED. IN NO EVENT SHALL THE REGENTS OR CONTRIBUTORS BE LIABLE

FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL

DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS

OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)

HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

 

 

OL-18083-01

 

 

2-109

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY

OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF

SUCH DAMAGE.

Using </> as the package base directory.

##Processing package information.

##Processing system information.

2 package pathnames are already properly installed.

##Verifying package dependencies.

##Verifying disk space requirements.

##Checking for conflicts with packages already installed.

##Checking for setuid/setgid programs.

This package contains scripts which will be executed with super-userpermission during the process of installing this package.

Do you want to continue with the installation of <SUNWftpu> [y,n,?]

Installing FTP Server, (Usr) as <SUNWftpu>

## Installing part 1 of 1. 577 blocks

Installation of <SUNWftpu> was successful. spawn pkgrm SUNWvtsmn

The following package is currently installed: SUNWvtsmn SunVTS Man Pages

(sparc) 6.4,REV=2007.07.05.12.46

Do you want to remove this package? [y,n,?,q] y

##Removing installed package instance <SUNWvtsmn>

##Verifying package <SUNWvtsmn> dependencies in global zone

##Processing package information.

##Removing pathnames in class <none> /opt/SUNWvts/man/man1m/vtsui.1m /opt/SUNWvts/man/man1m/vtstty.1m /opt/SUNWvts/man/man1m/vtsprobe.1m /opt/SUNWvts/man/man1m/vtsk.1m /opt/SUNWvts/man/man1m/vts_cmd.1m /opt/SUNWvts/man/man1m/sunvts.1m

...

/opt/SUNWvts/lib/locale/C <shared pathname not removed> /opt/SUNWvts/lib/locale <shared pathname not removed> /opt/SUNWvts/lib <shared pathname not removed> /opt/SUNWvts <shared pathname not removed>

## Updating system information.

Removal of <SUNWvtsmn> was successful. spawn pkgrm SUNWvtsr

The following package is currently installed: SUNWvtsr SunVTS Framework (Root)

(sparc) 6.4,REV=2007.07.05.10.00

Do you want to remove this package? [y,n,?,q] y

##Verifying package <SUNWvtsr> dependencies in global zone

##Processing package information.

##Removing pathnames in class <none> /etc/opt/SUNWvts/sunvts.conf.example /etc/opt/SUNWvts

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

2-110

OL-18083-01

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

/etc/opt <shared pathname not removed> /etc <shared pathname not removed>

## Updating system information.

Removal of <SUNWvtsr> was successful. spawn pkgrm SUNWvtsts

The following package is currently installed: SUNWvtsts SunVTS for Tests

(sparc) 6.4,REV=2007.07.05.12.46

Do you want to remove this package? [y,n,?,q] y

##Removing installed package instance <SUNWvtsts>

##Verifying package <SUNWvtsts> dependencies in global zone

##Processing package information.

##Removing pathnames in class <none> /opt/SUNWvts/lib/sparcv9 <shared pathname not removed> /opt/SUNWvts/lib/probe/sunlink_probe.so /opt/SUNWvts/lib/probe/ssptest_probe.so /opt/SUNWvts/lib/probe/sparcv9/xnetlbtest_probe.so /opt/SUNWvts/lib/probe/sparcv9/vmemtest_probe.so

...

/opt/SUNWvts/bin/cmos.bin

/opt/SUNWvts/bin/bios.bin

/opt/SUNWvts/bin <shared pathname not removed> /opt/SUNWvts <shared pathname not removed>

## Updating system information.

Removal of <SUNWvtsts> was successful. spawn pkgrm SUNWvts

The following package is currently installed: SUNWvts SunVTS Framework

(sparc) 6.4,REV=2007.07.05.10.00

Do you want to remove this package? [y,n,?,q] y

##Removing installed package instance <SUNWvts>

##Verifying package <SUNWvts> dependencies in global zone

##Processing package information.

##Removing pathnames in class <none> /opt/SUNWvts/lib/sparcv9/libvtsutil.so.1 /opt/SUNWvts/lib/sparcv9/libvtsutil.so /opt/SUNWvts/lib/sparcv9/libvtsthm.so.1

...

/opt/SUNWvts/bin

/opt/SUNWvts/README

/opt/SUNWvts

## Updating system information.

Removal of <SUNWvts> was successful. x SUNWvts, 0 bytes, 0 tape blocks

x SUNWvts/archive,

0

bytes,

0

tape blocks

x

SUNWvts/archive/none.bz2,

877058

bytes, 1714 tape blocks

x

SUNWvts/install,

0

bytes,

0

tape

blocks

 

x SUNWvts/install/checkinstall,

971 bytes, 2 tape blocks

 

x SUNWvts/install/copyright, 93

bytes, 1 tape blocks

...

 

 

 

 

 

 

Cisco PGW 2200 Softswitch Release 9.8 Software Installation and Configuration Guide

 

 

 

 

OL-18083-01

 

 

2-111

 

 

 

 

 

Chapter 2 Installing the Sun Solaris 10 Operating System

Loading the Sun Solaris 10 Operating Environment

x SUNWvts/reloc/sunwvts/lib/locale/c/LC_MESSAGES, 0 bytes, 0 tape blocks x SUNWvts/reloc/sunwvts/lib/sparcv9, 0 bytes, 0 tape blocks

spawn pkgadd -d .SUNWvts

Processing package instance <SUNWvts> from </tmp>

SunVTS Framework(sparc) 6.4,REV=2007.07.05.10.00

Copyright 2007 Sun Microsystems, Inc. All rights reserved. Use is subject to license terms.

## Executing checkinstall script.

Using </opt> as the package base directory.

##Processing package information.

##Processing system information.

##Verifying package dependencies.

##Verifying disk space requirements.

##Checking for conflicts with packages already installed.

##Checking for setuid/setgid programs.

This package contains scripts which will be executed with super-userpermission during the process of installing this package.

Do you want to continue with the installation of <SUNWvts> [y,n,?] y

Installing SunVTS Framework as <SUNWvts>

## Installing part 1 of 1. 8132 blocks

Installation of <SUNWvts> was successful. x SUNWvtsts, 0 bytes, 0 tape blocks

x SUNWvtsts/archive, 0 bytes, 0 tape blocks

x SUNWvtsts/archive/none.bz2, 9661272 bytes, 18870 tape blocks x SUNWvtsts/install, 0 bytes, 0 tape blocks

x SUNWvtsts/ins