Quick Start Installation of SubliJet IQ® for the
EPSON Stylus® Pro 4880
IMPORTANT:
Do not install Epson Inks provided with the printer. Please call Sawgrass Technical Support
if you need assistance installing the SubliJet IQ inks.
STEPS FOR INSPECTING SUBLIJET IQ CARTRIDGES FOR LOOSE CHIPS:
1. Check the product package to ensure that the chip
remains attached to the cartridge itself and has not
dislodged in the plastic bag.
2. Determine if the chip is securely attached by tapping
the cartridge a few times on a hard surface, watching
to ascertain that the jolt does not dislodge the chip.
3. Once the cartridge is removed from the bag, rub an
eraser over the surface of the chip, to determine if it
remains stationary within it’s mounting slot. Use of
any item other than an eraser is not advised and can
damage the chip. (See photo @ far right.)
Rotate Cartridge
INSTALLING SUBLIJET IQ CARTRIDGES:
If you are replacing existing cartridges because they are empty or low,
please see the following instructions. If not, go directly to step #1.
2.Raise both ink levers. (Located @ the right side
of each ink cartridge compartment.)
Rub chip with an eraser to determine
stability of attachment to cartridge.
Note: Use only a
pencil eraser to rub
chip surface to avoid
damaging chip.
CHIP LOCATION
& ORIENTATION
When a cartridge is empty or extremely low, “INK OUT” will
display on the LCD panel. Raise the ink levers on either side of the
printer. The cartridge position indicator on the LCD panel will flash
on and off, indicating which cartridge is low or empty. Be sure you
have the correct color cartridge replacement for that position.
1 2 3 4 5 6 7 8
Menu
3sec.
Position # 5: Empt y
or Ex tremely Low
4880 Control Panel
NOTE: The LCD Panel will indicate the ink colors of the original
OEM ink configuration and not the SubliJet ink
configuration. (See Figure # 3 to the right.
1.Ensure the printer power is on.
Press the ink compartment cover
to release the latch and open the
cover.
3. Install the ink cartridges into the colorcoded
slots in the order that your system is currently
using, starting from left to right.
Note: Cartridge label must face left as cartridge is inserted into slot.
4. After all eight cartridges are installed, lower
the ink levers.
5. After approximately 1 minute, ink lever messages will appear on
the LCD panel. The LCD will indicate that the printer recognized
“NON-GENUINE” ink cartridges.
NON-GENUI N
3sec.
E
1 2 3 4 5 6 7 8
Menu
INSTALLING SUBLIJET IQ CARTRIDGES (CONTINUED):
6. Press the down key (V) until a message
appears that asks the user whether the
ink cartridges are “NON-GENUINE”.
YES
1 2 3 4 5 6 7 8
Menu
3sec.
7. Press the left key (<) to acknowledge that
the cartridges are “NON-GENUINE”.
YES
1 2 3 4 5 6 7 8
Menu
3sec.
10. Press the left key (<) to accept acknow-
ledgement of the warranty message.
ACPT. D
E-
1 2 3 4 5 6 7 8
3sec.
Menu
11. The following message will appear:
PLEASE W
3sec.
A I T
1 2 3 4 5 6 7 8
Menu
12. Then the following message:
SubliJet IQ® sublimation ink
systems offer a total solution
for delivering sublimation inks.
By choosing the industry’s
highest-quality sublimation
inks, SubliJet IQ users enjoy
PartnerPlus® (a comprehensive
support program) and
PowerDriver® (the award
winning, user-friendly software)
which makes achieving
high-quality digital images a
simple reality. If you are new
8. Press the left key (<) until the following
message appears:
T
H I S MA
Y VO ID
1 2 3 4 5 6 7 8
3sec.
Menu
9.Pressthedownkey(V)untilthe
followingmessageappears:
ACPT. D
E-
1 2 3 4 5 6 7 8
3sec.
Menu
PAUS
E
1 2 3 4 5 6 7 8
3sec.
Menu
13. Press the “PAUSE” key once.
PAUS
E
1 2 3 4 5 6 7 8
3sec.
Menu
14. The following message will appear. The
printer is now ready for use.
READY
1 2 3 4 5 6 7 8
3sec.
Menu
to sublimation or enjoy the
peace of mind that comes with
expert-level support, then think
SubliJet IQ sublimation inks!
EPSON is a registered trademark of Epson Seiko Corporation.
SubliJet, Partner Plus, and Power Driver are all registered
trademarks of Sawgrass Technologies, Inc.
Loading...