Whirlpool ASE 549, ASE 550, ASE 551, ASE 552, ASE 553 INSTRUCTIONS FOR INSTALLING AND USING THE BAIN MARIE UNITS AND HEATED GLASS TOPS

GB

Design Series Traditional Series 800 Traditional Series 700

BAIN-MARIE UNITS AND

HEATED GLASS TOPS

ASE 549	ASE 573	ASE 597	ASE 621	ASE 346	ASE 031
ASE 550	ASE 574	ASE 598	ASE 622	ASE 347	ASE 032
ASE 551	ASE 575	ASE 599	ASE 324	ASE 348	ASE 033
ASE 552	ASE 576	ASE 600	ASE 325	ASE 349	ASE 034
ASE 553	ASE 577	ASE 601	ASE 326	ASE 350	ASE 035
ASE 554	ASE 578	ASE 602	ASE 327	ASE 351	ASE 036
ASE 555	ASE 579	ASE 603	ASE 328	ASE 352	ASE 037
ASE 556	ASE 580	ASE 604	ASE 329	ASE 353	ASE 038
ASE 557	ASE 581	ASE 605	ASE 330	ASE 354	ASE 039
ASE 558	ASE 582	ASE 606	ASE 331	ASE 355	ASE 040
ASE 559	ASE 583	ASE 607	ASE 332	ASE 356	ASE 041
ASE 560	ASE 584	ASE 608	ASE 333	ASE 357	ASE 042
ASE 561	ASE 585	ASE 609	ASE 334	ASE 358	ASE 043
ASE 562	ASE 586	ASE 610	ASE 335	ASE 359	ASE 044
ASE 563	ASE 587	ASE 611	ASE 336	ASE 360	ASE 045
ASE 564	ASE 588	ASE 612	ASE 337	ASE 022	ASE 046
ASE 565	ASE 589	ASE 613	ASE 338	ASE 023	ASE 047
ASE 566	ASE 590	ASE 614	ASE 339	ASE 024	ASE 048
ASE 567	ASE 591	ASE 615	ASE 340	ASE 025	ASE 049
ASE 568	ASE 592	ASE 616	ASE 341	ASE 026
ASE 569	ASE 593	ASE 617	ASE 342	ASE 027
ASE 570	ASE 594	ASE 618	ASE 343	ASE 028
ASE 571	ASE 595	ASE 619	ASE 344	ASE 029
ASE 572	ASE 596	ASE 620	ASE 345	ASE 030

INSTRUCTIONS FOR INSTALLING AND

USING THE BAIN MARIE UNITS AND HEATED GLASS TOPS THESE APPLIANCES CONFORM TO THE FOLLOWING DIRECTIVES:

73/23 EEC: LOW VOLTAGE, ELECTRICAL SAFETY 89/336 EEC: ELECTROMAGNETIC COMPATIBILITY

93/68 EEC: EC MARKING REGULATIONS

Ed: A	Data	Evento modifica	Redatto	Verificato	Approvato
Rev: Ø	01.01.2002	Prima emissione	-	-	-
Rev: 1	30.06.2005	Revisione Lay-Out	RSSC	ULGR	TNPL
Rev: 2

SUMMARY

1.	GENERAL WARNINGS	pg.3
2.	SPECIAL WARNINGS FOR POSITIONING AND WIRING THE APPLIANCE	pg.3
3.	POSITIONING	pg.4
4.	LEGAL PROVISIONS AND DIRECTIVES	pg.4
5.	ELECTRICAL AND EQUIPOTENTIAL WIRING	pg.4
6.	WATER CONNECTIONS	pg.5
7.	GENERAL OPERATING INSTRUCTIONS	pg.5
8.	CLEANING AND CARE	pg.6
9.	CONTROL PANEL	pg.6
10.USE AND FUNCTIONS		pg.7

The manufacturer declines all responsibility for any printing or copying errors in this handbook.

The manufacturer reserves the right to make any changes deemed necessary or useful to its products without altering the basic features.

All rights reserved. No part of this publication may be reproduced or photocopied without prior permission from the manufacturer.

2

1. GENERAL WARNINGS

Only qualified installers and staff authorised by the manufacturer may perform the installation, start-up and maintenance work to the appliance.

Read these instructions carefully beforehand, as they are very important for safety when installing, using and servicing the appliance.

1.The appliance must only be used in the manner it was designed for, i.e. keeping previously cooked dishes hot; any other use does not conform to its design and is therefore strictly forbidden.

2.The ideal working conditions for the appliance are a temperature of 25°C with a humidity level of 60%.

3.After unpacking the appliance, ascertain that no damage has been caused during transport.

4.Before positioning and installing the appliance, check that the output and voltage features given on the data plate correspond to the power supply in the installation site.

The data plate is on the bottom right of the serving side.

5.In the event of problems, immediately turn the machine off and disconnect or close all connections.

2. SPECIAL WARNINGS FOR POSITIONING AND WIRING THE APPLIANCE

As prescribed by law, a multiple-pole switch must be installed between the appliance and the main power supply, with a contact opening of at least 3 mm per pole. The ground wire must not be disconnected. A water cut-off valve must be installed upstream from the bain-marie units; we recommend using only softened water. The appliance may be connected to the hot water line, to reduce the time required to reach the operating temperature.

3