tekmar 529 Quick Start

Quick Setup Guide

tekmarNet®2 Thermostat 529

Location1. Remove Mounting Base2.

Interior

Wall

5 feet

1.5 m

Exterior

Wall

Install Mounting Base3. Wiring4.

Zoning

Q 529

12/11

Replaces: 01/11

Plate 007

Thermostat

Base

Switch Settings5.

Switch

1

2

3

4

Adaptor

Thermostat

Base

OR

Switch

Box

Position

ON

OFF OFF No setback schedule response.

ON

OFF OFF No scene response.

ON

OFF

ON Not used

OFF Not used

Action

SETBACK Allow thermostat to respond to

available schedule. Requires Timer 033.

SCENE Allow thermostat to respond to
scenes. Requires User Switch 479.

LOCK Locked to ‘User’ access level. Set
to Lock when installation completed.
UNLOCK Unlock to access all settings.
Set to Unlock during installation.

Wall

Two Stage Method 2

W R

Heating Equipment

Two Stage Method 1

tN2

tN2

Zone 1

Zone 1

Stage 1 Stage 2

tN2tN2

Zone 2

Close Thermostat6.

pivot

tab

6

W2

5

Rh

For instructions see brochure
Use at least 65°C conductors

No Power

tN21tN2

Sensor

2

34

529

ON

Switch Settings:

1023-03

Scene

Lock

Setback

Unlock

Off

Off

1234

12 34

Not used

Not used

Mmm YYYY

Meets Class B:

Canadian ICES

tNt 529

Two Stage Heat

Relays: 24V (ac) 2A

Switch Setting Location

Slab Sensor 079, or

Outdoor Sensor 070, or

Indoor Sensor 076, 077, 084

Lot # 12345

FCC Part 15

1 of 2 © 2010 Q 529 - 12/11

User Interface7.

Critical Settings8.

The following settings are essential to the successful operation of the system.
Important Note: Set switch setting #3 and tekmarNet® system control to Unlock to change Access level to Installer. Return

to Lock setting once installation has been completed.

Press

• Press and hold down both the and buttons for 2 seconds to change from one step to the next.

• Release both buttons once the step has been reached.

+

• Press the or the button to change the setting, if available.

• Press and hold down both the and buttons for 2 seconds to go to the next step, OR

Toget her

• After 10 seconds of no button activity, the display goes back to normal operation.

Display Range Access Description Set to

ROOM SENSOR

Select whether the built-in air temperature sensor is

On or Off

Default = On

Installer

on or off.
Available when:

A floor sensor or room sensor is installed on the
auxiliary sensor input.

AUXILIARY SENSOR

Off, Room,

Outdoor,

Floor, Floor

dSP

Installer

Select the type of auxiliary sensor.
Floor dSP = Show floor sensor reading in upper

number field.
Available when:
Auxiliary sensor automatically detected.

HEAT 1 SUPPLY PUMP

Select whether the system supply pump should turn

OFF, On

Default = On

Installer

on during a call for first stage heat, or be off to allow a
zone group pump per manifold.
Available when:

A reset control is present on the tekmarNet® system.•

HEAT 1 SUPPLY PUMP DELAY

OFF, On

Default = Off

Installer

Select whether or not the system supply pump should
be delayed by 3 minutes before coming on (for thermal
motor or wax actuator).

HEAT 2 SOURCE

bLr,

M1, M2, or

M3, otH

Default = bLr

Installer

Select whether the second stage heat is on the boiler
bus (bLr), mix 1 (M1), mix 2 (M2), or mix 3 (M3) bus, or
non-hydronic other (otH).
Available when:

•

A reset control is present on the tekmarNet
There is an active room sensor.

•

®

system.

For a full list of settings and operational details, please refer to the thermostat Installation and Operation Manual
(D529) included with this thermostat or download the brochure from www.tekmarcontrols.com

tekmar Control Systems Ltd., Canada, tekmar Control Systems, Inc., U.S.A.

Vernon, B.C. Canada V1B 3K4, 250-545-7749, Fax. [phone] Web Site: www.tekmarcontrols.com

Product design, sof tware and literature are Copyright © 2010 by:
tekmar Control Systems Ltd. and tekmar Control Systems, Inc.

2 of 2

All specifications are subject to change without notice.

Head Offi ce: 5100 Silver Star Road,

Printed in Canada. Q 529 - 12/11.