Loading...
Installation Manual
Additional Digital Cordless Handset
Model No. KX-PRSA10
KX-PRWA10
KX-PRSA10 |
KX-PRWA10 |
Thank you for purchasing a Panasonic product.
This unit is an additional handset compatible with the following series of Panasonic Digital Cordless Phone:
-KX-PRS120 (KX-PRSA10)
-KX-PRW120 (KX-PRWA10)
(The corresponding models are subject to change without notice.)
You must register this handset with your base unit before it can be used. This installation manual describes only the steps needed to register and begin using the handset. Please read the base unit’s operating instructions for further details.
Please read this installation manual before using the unit and save it for future reference.
For assistance, visit our Web site: http://www.panasonic.com/help for customers in the U.S.A. or Puerto Rico.
Printed in China |
PNQX6063ZA TT0913MG0 (E) |
Installation
Accessory information
Supplied accessories
Accessory item/Order number |
Quantity |
|
Charger*1 |
1 |
|
AC adaptor/PNLV233Z |
1 |
|
Rechargeable batteries/HHR-4DPA |
2 |
|
Handset cover*2, *3 |
1 |
|
*1 |
KX-PRSA10: PNLC1047ZW |
|
|
KX-PRWA10: PNLC1046ZW |
|
*2 |
The handset cover comes attached to the handset. |
|
*3 |
KX-PRSA10: PNYNPRSA10WR |
|
|
KX-PRWA10: PNYNPRWA10WR |
|
Note:
RPlease read the base unit’s operating instructions for additional/replacement accessories.
Setting up
Connections
Connect the AC adaptor plug to the unit until you hear a click.
Connect the AC adaptor to the power outlet. KX-PRSA10: Fasten the cord by hooking it.
n KX-PRSA10 |
n KX-PRWA10 |
1
2 1
3
2
2For assistance, please visit http://www.panasonic.com/help
Installation
Note:
RUse only the supplied Panasonic AC adaptor PNLV233.
RThe AC adaptor must remain connected at all times. (It is normal for the adaptor to feel warm during use.)
Battery installation/Battery charging
Important:
RUse the supplied rechargeable batteries. For replacement, we recommend using the Panasonic rechargeable batteries noted on page 2.
RUSE ONLY rechargeable Ni-MH batteries AAA (R03) size (1).
RDo NOT use Alkaline/Manganese/Ni-Cd batteries.
RConfirm correct polarities (
, ).
Charge for about 7 hours.
RConfirm “Charging” is displayed (2).
RWhen the batteries are fully charged, “Fully charged” is displayed.
n KX-PRSA10
2
n KX-PRWA10
2
1
For assistance, please visit http://www.panasonic.com/help |
3 |
Installation
Note:
RIf the batteries are fully charged, but the operating time seems to be shorter,
clean the battery ends (
, 
) and the charge contacts with a dry cloth and charge again.
Registering a handset to a base unit
1Handset:
Lift the handset and press MOFFN.
2Base unit:
Press and hold M
N for about 5 seconds.
R If all registered handsets start ringing, press M
N again to stop, then repeat this step.
n KX-PRSA10 |
n KX-PRWA10 |
|||
{x} |
{x} |
|||
|
|
|||
|
|
|
|
|
|
|
|
|
|
3Handset:
Place the handset on the base unit or charger, then wait until a long beep sounds and 
is displayed.
Note:
RIf an error tone sounds, or if 
is displayed, register the handset according to the base unit’s operating instructions.
Display language
1MMenuN (right soft key) #110
2MbN: Select the desired setting. a MSaveN a MOFFN
For your safety
To prevent severe injury and loss of life/property, read this section carefully before using the product to ensure proper and safe operation of your product.
4For assistance, please visit http://www.panasonic.com/help
Loading...